00 / 21 COVER SHEET01 / 21 PARAPET AND BALUSTRADE CAPPING02 / 21 SCUPPER W/ RAINWATER HEAD03 / 21 SOFFIT04 / 21 BUTT WINDOW HEAD05 / 21 BUTT WINDOW SILL06 / 21 BUTT WINDOW JAMB07 / 21 RECESSED WINDOW HEAD08 / 21 RECESSED WINDOW SILL09 / 21 RECESSED WINDOW JAMB10 / 21 METERBOX HEAD11 / 21 METERBOX SILL12 / 21 METERBOX JAMB13 / 21 INTERNAL CORNER14 / 21 EXTERNAL CORNER15 / 21 SOAKER FLASHING16 / 21 CHANGE IN CLADDING17 / 21 CLADDING ABUTMENT18 / 21 BOTTOM OF CLADDING (FLUSH)19 / 21 BOTTOM OF CLADDING (RECESSED)20 / 21 3D WINDOW FLASHINGS21 / 21 3D RAINWATER HEAD

DETAIL LISTCOMMERCIAL VERTICAL CLADDING

Espan 340™ / 470™

CVEP

0800 ROOFNZ (0800 766 369)www.metalcraftgroup.co.nz

Architectural / Specification EnquiriesPh: 09 274 0408

Mobile: 027 603 1096Email: Frances.charles@unitedindustries.co.nz

PRE-FINISHED PARAPET CAPFLASHINGNO FIXINGS ON TOP OF FLASHING

PERMEABLE WALLUNDERLAY, SHOWNDASHED

PRE-FINISHED SELF DRILLING /TAPPING SCREW WITH RUBBERWASHER FOR FIXING TOP OFESPAN™ CLADDING

METALCRAFT ESPAN™ VERTICALCLADDING

METALCRAFT MSS PURLINBY ENGINEER

CONTINUOUS TIMBER PACKING MIN

. 5°

PERMEABLE WALL UNDERLAY TOPROVIDE SEPARATION OF METALCAPPING AND TIMBER, SHOWNDASHED

PRE-FINISHED POP RIVETBEDDED IN SILICONE ORPRE-FINISHED 8g WAFER-TEK SCREW

STOPENDS TO WALL CLADDING

20mm HORIZONTAL CAVITY BATTEN

CLE

ARAN

CE

25m

m M

IN

5mm GAP

MIN

. 5.00 °

ALTERNATIVE OPTION

5mm GAP

5mm GAP

CLE

ARAN

CE

25m

m M

IN.

CLE

A RAN

CE

3mm

MIN

COMPRESSIBLE FOAMSEAL. REFER TO MRM CODEOF PRACTICE VERSION 2.2/2012 FOR REQUIRMENT.

Z

Z

Z

CATEGORY A

1. NORMAL EXPOSURE2. ROOF PITCH >10°

MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH)

MIN. 75mm (VERTICALLY DOWN FACE - PROFILED)

CATEGORY B

1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°

MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH)

MIN. 100mm (VERTICALLY DOWN FACE - PROFILED)

Z

ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE

SITUATION 1

1. LOW, MEDIUM, HIGH WINDZONES, WHERE ROOF PITCH ≥ 10°

MIN. 50mm

SITUATION 2

1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°

MIN. 70mmZ

SITUATION 3

1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES

MIN. 90mm

ACCEPTABLE SOLUTION AS PER E2/ASI

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

PARAPET AND BALUSTRADE CAPPING

01 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

METALCRAFT ESPAN™ VERTICALCLADDING

PERMEABLE WALLUNDERLAY, SHOWNDASHED

20mm HORIZONTALCAVITY BATTEN

WALL FRAMING

CAVITY CLOSER

RETURN MEMBRANE INTORAINWATER HEAD

CONTINUOUS MEMBRANEDRESSED THROUGH BASE ANDUP SIDES OF OPENING WITHUPPER EDGES SEALED AGAINSTCLADDING. RETURN ALONGBACK OF RAINWATERHEAD

RAINWATER HEAD

RETURN MEMBRANEAT END OF LIP

MEMBRANE ON ROOFSUBSTRATE

8g WAFER-TEK SCREW

TRUE ROOF LINE BEHIND

PRE FINISHED SCREWWITH RUBBER WASHER

25RAINWATER HEADOVERFLOW BELOWOPEINING LEVEL,1.5 xCROSS-SECTIONDOWNPIPE DIAMETER

50 mm

SEPARATE BATTEN ANDCLADDING ASREQUIRED WITH EPDM

ALTERNATIVE OPTION

METALCRAFT ESPAN™ CLIP SYSTEMWITH 12G x 16mm WAFERTEK

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

SCUPPER W/ RAINWATER HEAD

02 / 212018

METALCRAFT MSS PURLINBY ENGINEER

INTERNAL WALL LINING

METALCRAFT MSS PURLIN BY ENGINEER

20mm HORIZONTAL CAVITYBATTEN

SEPARATE BATTEN ANDCLADDING WITH DPC ASREQUIRED

BARGE BOARD

SOFFIT LINING

METALCRAFTMSS PURLIN BYENGINEER

PRE-FINISHED SELFDRILLING/TAPPING SCREWWITH RUBBER WASHER FORFIXING TOP OF ESPAN™CLADDING

INTERNAL CEILING LINING

COMPRESSIBLE FOAM SEAL. REFER TO MRM CODEOF PRACTICE VERSION 2.2 /2012 FOR REQUIRMENT.

PRE-FINISHEDSOFFIT FLASHING

PRE-FINISHED FLAT HEAD WAFER-TEK SCREWFOR FLASHING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

METALCRAFT ESPAN™ VERTICALCLADDING

PRE-FINISHED POP RIVETBEDDED IN SILICONE OR PRE-FINISHED 8g WAFER-TEKSCREW

STOPENDS TO WALL CLADDING

5mm GAP50mm MIN

100m

m M

IN

MIN. 50mm

100m

m M

IN

5mm GAP

ALTERNATIVE OPTION

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

SOFFIT

03 / 212018

BUILDING PAPER DRESSED INTOOPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA PERMEABLE WALL UNDERLAYOVER WINDOW HEAD FLASHING, SHOWNDASHED

INTERNAL WALL LINING

METALCRAFT ESPAN™ VERTICALCLADDING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

DOUBLE GLAZING WINDOW JOINERY

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

WINDOW HEAD LINER

LINE OF WINDOW JAMBLINER BEHIND

STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

METALCRAFT MSS PURLINS BYENGINEER

METALCRAFT ESPAN™ CLIPSYSTEM WITH 12G x 16mm WAFER-TEK

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

CAVITY CLOSER AS REQUIRED TONZBC

5mm

GAP

MIN

. 10m

m C

OVE

R

SUG

GES

T M

IN. 5

0mm

DIM

ENSI

ON

TO

SU

ITDR

IP E

DG

E TO

CLA

DD

ING

MIN

.15m

m G

AP

MIN

.75m

m W

ITH

OU

T H

EM E

DG

E

MIN

.50m

m C

OVE

R

20mm HORIZONTAL CAVITY BATTEN

5mm

GAP

MIN

. 10m

m C

OVE

R

SUG

GES

T M

IN. 5

0mm

DIM

ENSI

ON

S TO

SU

ITDR

IP E

DG

E TO

CLA

DD

I NG

MIN

. 15m

m

MIN

. 75m

m W

I TH

OU

T H

EM E

DG

E

MIN

. 50m

m C

OVE

R

ALTERNATIVE OPTION

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

BUTT WINDOW HEAD

04 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

PRE-FINISHED WINDOW SILL FLASHING

LINE OF WINDOW JAMBLINER BEHIND

WINDOW SILL LINER

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

INTERNAL WALL LINING

STOPENDS TO SILL FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER FORFIXING TOP OF ESPAN™ CLADDING

20mm HORIZONTAL CAVITY BATTEN

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FORFULL WIDTH/DEPTH SILL

DOUBLE GLAZING WINDOW JOINERY

METALCRAFT MSS PURLIN BYENGINEER

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

SEPARATE BATTEN AND CLADDINGWITH DPC AS REQUIRED

WINDOW SILL SUPPORT BAR

5mm GAP

CO

VER

CLA

DD

ING

60m

m

5mm

GAP

MIN

. 8m

m C

OVE

R

ALTERNATIVE OPTION

5mm GAP

CO

VER

CLA

DD

ING

60m

m

5mm

GAP

MIN

. 8m

m C

OVE

R

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet

- DEPENDING ON ACTUAL SITUATION, A SECONDARY FLASHINGMAY BE REQUIRED. REFER METALCRAFT ROOFING FOR MOREINFORMATION.

1 : 2

BUTT WINDOW SILL

05 / 212018

PRE-FINISHED WINDOW JAMB FLASHING

DOUBLE GLAZING WINDOW JOINERY

LINE OF SILL FLASHING BELOW

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED FIXING BRACKET WITH PRE-FINISHED POP RIVET BEDDED IN SILICONEOR PRE-FINISHED 8g WAFER-TEK SCREW

METALCRAFT ESPAN™VERTICAL CLADDING

MIN.10mm COVER

5mm GAP

INTERNAL WALL LINING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

LINE OF WINDOW SILL LINER BELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

20mm JAMB BATTEN

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FOR FULLWIDTH/DEPTH SILL

METALCRAFT MSS PURLIN BYENGINEER

SUGGEST MIN.50mm

DIMENSION TO SUIT

PRE-FINISHED SECONDARYFLASHING

LINE OF SILL FLASHING BELOW

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

LINE OF HEAD FLASHING ABOVE

LINE OF HEAD FLASHING ABOVE

SEPARATE BATTEN AND FLASHINGWITH DPC AS REQUIRED

5mm

GAP

20mm HORIZONTAL CAVITYBATTEN

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet

- DEPENDING ON ACTUAL SITUATION, A SECONDARY FLASHINGMAY BE REQUIRED. REFER METALCRAFT ROOFING FOR MOREINFORMATION.

1 : 2

BUTT WINDOW JAMB

06 / 212018

PERMEABLE WALL UNDERLAYDRESSED INTO OPENING WITHFLEXIBLE FLASHING TAPE INSTALLEDOVER WRAP TO CORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA PERMEABLE WALL UNDERLAYOVER WINDOW HEAD FLASHING,SHOWN DASHED

INTERNAL WALL LINING

METALCRAFT ESPAN™ VERTICALCLADDING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

DOUBLE GLAZING WINDOW JOINERY

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

WINDOW HEAD LINER

LINE OF WINDOW JAMBLINER BEHIND

STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

MIN

. 10m

m C

OVE

R

METALCRAFT MSS PURLINS BYENGINEER

METALCRAFT ESPAN™ CLIPSYSTEM WITH 12G x 16mm WAFER-TEK

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

MIN

15

mm

GAP

MIN

. 75m

m W

ITH

OU

T H

EM E

DG

E

MIN

50m

m C

OVE

R

SUG

GES

T M

IN. 5

0mm

DIM

ENSI

ON

TO

SU

IT

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

CAVITY CLOSER AS REQUIRED TONZBC

5mm

GAP

20mm HORIZONTAL CAVITY BATTEN

5mm

GAP DR

IP E

DG

E TO

CLA

DD

I NG

MIN

15m

m G

AP

MIN

. 75m

m W

I TH

OU

T H

EM E

DG

E

MIN

. 50m

m C

OVE

R

SUG

GES

T M

IN. 5

0mm

DIM

ENSI

ON

TO

SU

IT

10m

m M

IN C

OVE

R

ALTERNATIVE OPTION

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

RECESSED WINDOW HEAD

07 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

PRE-FINISHED WINDOW SILL FLASHING

LINE OF WINDOW JAMBLINER BEHIND

WINDOW SILL LINER

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

INTERNAL WALL LINING

STOPENDS TO SILL FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER FORFIXING TOP OF ESPAN™ CLADDING

20mm HORIZONTAL CAVITY BATTEN

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FORFULL WIDTH/DEPTH SILL

DOUBLE GLAZING WINDOW JOINERY

METALCRAFT MSS PURLIN BYENGINEER

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

SEPARATE BATTEN AND FLASHINGWITH DPC AS REQUIRED

WINDOW SILL SUPPORT BAR

5mm GAP

CO

VER

CLA

DD

ING

60m

m

5mm

GAP

MIN

. 8m

m C

OVE

R

ALTERNATIVE OPTION

5mm GAP

CO

VER

CLA

DD

ING

60m

m

5mm

GAP

MIN

. 8m

m C

OVE

R

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

RECESSED WINDOW SILL

08 / 212018

PRE-FINISHED WINDOW JAMB FLASHING

DOUBLE GLAZING WINDOW JOINERY

LINE OF SILL FLASHING BELOW

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED FIXING BRACKET WITH PRE-FINISHED POP RIVET BEDDED IN SILICONEOR PRE-FINISHED 8g WAFER-TEK SCREW

METALCRAFT ESPAN™ VERTICALCLADDING

MIN. 10mm COVER

INTERNAL WALL LINING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

LINE OF WINDOW SILL LINER BELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

20mm JAMB BATTEN

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FOR FULLWIDTH/DEPTH SILL

METALCRAFT MSS PURLIN BYENGINEER

PRE-FINISHED SECONDARYFLASHING

LINE OF SILL FLASHING BELOW

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

LINE OF HEAD FLASHING ABOVE

SEPARATE BATTEN AND FLASHINGWITH DPC AS REQUIRED

SUGGEST MIN. 50mm

DIMENSION TO SUIT

5mm GAP

LINE OF HEAD FLASHING ABOVE

20mm HORIZONTAL CAVITYBATTEN

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

RECESSED WINDOW JAMB

09 / 212018

PERMEABLE WALL UNDERLAY DRESSEDINTO OPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA PERMEABLE WALL UNDERLAYOVER WINDOW HEAD FLASHING, SHOWNDASHED

METALCRAFT ESPAN™ VERTICALCLADDING

PRE-FINISHED HEAD FLASHINGWITH 15° FALL

METALCRAFT ESPAN™ CLIP SYSTEMWITH 12G x 16mm WAFER-TEK

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD, SILLAND JAMB

METER BOX STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED 'U' BRACKET FIXED TOMETERBOX BEFORE INSTALLATION

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX.

INTERNAL WALL LINING

METALCRAFT MSS PURLINS BYENGINEER

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

CAVITY CLOSER AS REQUIRED TO NZBC

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

20mm HORIZONTAL CAVITY BATTEN

5mm

GAP

MIN

. 15m

m G

AP

MIN

. 75m

m W

I TH

OU

T H

EM E

DG

E

MIN

. 50m

m C

OVE

R

ALTERNATIVE OPTION

5mm

GAP

MIN

. 15m

m G

AP

MIN

. 75m

m W

I TH

OU

T H

EM E

DG

E

MIN

. 50m

m C

OVE

R

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

METERBOX HEAD

10 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

PERMEABLE WALL UNERLAY,SHOWN DASHED

METER BOX

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD, SILLAND JAMB

METALCRAFT MSS PURLINBY ENGINEER

INTERNAL WALL LINING

LINE OF JAMB FLASHING BEHIND

20mm HORIZONTAL CAVITY BATTEN

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FOR FULLWIDTH/DEPTH SILL

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX. PRE-FINISHED FLASHING FIXED TO

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX.

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

SEPARATE BATTEN AND FLASHINGWITH DPC AS REQUIRED

CO

VER

CLA

DD

NIN

G

60m

m M

IN

STOPENDS TO SILL FLASHING

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

STOPENDS TO WALL CLADDING

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER FORFIXING TOP OF ESPAN™ CLADDING

5mm GAP

5mm gap

ALTERNATIVE OPTION

CO

VER

CLA

DD

ING

60m

m M

IN

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

METERBOX SILL

11 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

PERMEABLE WALL UNDERLAY,SHOWN DASHED

METER BOX

TIMBER PACKER

20mm JAMB BATTEN

LINE OF SILL FLASHING BELOW

FLEXIBLE FLASHING TAPE OVERPERMEABLE WALL UNDERLAY FOR FULLWIDTH/DEPTH SILL

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED JAMB FLASHING FIXEDTO METERBOX BEFORE INSTALLATION

AIRSEAL ON BACKING ROD

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX.

INTERNAL WALL LINING METALCRAFT MSS PURLINBY ENGINEER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

LINE OF HEAD FLASHING ABOVE

LINE OF SILL FLASHING BELOW

20mm HORIZONTAL CAVITYBATTEN

5mm

GAP

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

METERBOX JAMB

12 / 212018

METALCRAFT ESPAN™VERTICAL CLADDING

20mm HORIZONTAL CAVITYBATTEN

PRE-FINISHED INTERNALCORNER FLASHING

INTERNAL WALL LINING

PERMEABLE WALLUNDERLAY, SHOWN DASHED

STRUCTURAL COLUMN BYENGINEER

METALCRAFT MSS PURLINBY ENGINEERPRE-FINISHED FLAT

HEAD WAFER-TEKSCREW WITH EPDMWASHER

PRE-FINISHED SECONDARYFLASHING

SEPERATE BATTEN ANDCLADDING WITH DPC ASREQUIRED

5mm GAP

5mm

GAP

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

INTERNAL CORNER

13 / 212018

METALCRAFT MSS PURLIN BYENGINEER

20mm HORIZONTAL CAVITYBATTEN

PRE-FINISHED EXTERNALCORNER FLASHING

PERMEABLE WALL UNDERLAY, SHOWNDASHED

METALCRAFT ESPAN™ VERTICALCLADDING

STRUCTURAL COLUMN BY ENGINEER

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW WITH EPDM WASHER

SEPERATE BATTEN AND CLADDING WITHDPC AS REQUIRED

5mm

GAP

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

EXTERNAL CORNER

14 / 212018

PERMEABLE WALLUNDERLAY, SHOWN DASHED

METALCRAFT ESPANVERTICAL CLADDING

PRE-FINISHED FLAT HEADWAFER-TEK SCREW WITHEPDM WASHER

INTERNAL WALL LINING

SEPARATE BATTEN ANDFLASHING WITH DPC ASREQUIRED

METALCRAFT MSS PURLINBY ENGINEER

PRE-FINISHED SOAKERFLASHING TO LINE UP WITHWINDOW JAMB ABOVE

20mm HORIZONTAL CAVITYBATTEN

METALCRAFT MSS PURLINBY ENGINEER

SOAKER FLASHING ONLY REQUIRED TOLINE UP WITH WINDOW JAMB ABOVE.REFER TO MRM CODE OF PRACTICEVERSION 2.2 /2012 FOR REQUIRMENT.

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

SOAKER FLASHING

15 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

PRE FINISHED SCREWWITH RUBBERWASHER

20mm HORIZONTAL CAVITYBATTEN FIBRE CEMENT BOARD

BY OTHERS

PRE FINISHEDALUMINIUM FLASHING

PERMEABLE WALLUNDERLAY, SHOWNDASHED

INTERNAL WALL LINING

SEPARATE BATTEN AND FLASHING ASREQUIRED WITH DPC

5mm

GAP

MIN. 50mm

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

CHANGE IN CLADDING

16 / 212018

METALCRAFT ESPAN™ VERTICALCLADDING

WALL FRAMINGPRE FINISHED SCREWWITH RUBBERWASHER

CONCRETE WALL BYOTHERS

CONTINUOUS AIR SEAL ONBACKING ROD

DPC

PRE FINISHED ALUMINIUMFLASHING

20mm HORIZONTALCAVITY BATTENSS

PRE-FINISHED POP RIVETBEDDED IN SILICONE

PERMEABLE WALLUNDERLAY, SHOWNDASHED

SEPARATE BATTEN ANDFLASHING AS REQUIREDWITH EPDM

INTERNAL WALLLINING

PRE-FINISHEDSECONDARY FLASHING

Mastic bead

5mm

GAP

ALTERNATIVE OPTION

Rawlplug

5mm

GAP

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

CLADDING ABUTMENT

17 / 212018

PERMEABLE WALL UNDERLAY, SHOWNDASHED

INTERNAL WALL LININGMETALCRAFT ESPAN™ VERTICALCLADDING

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

CAVITY CLOSER AS REQUIRED TONZBC

PRE-PRIMED SKIRTING

CONCRETE SLAB

METALCRAFT MSS PURLIN BYENGINEER

METALCRAFT ESPAN™ CLIP SYSTEMWITH 12G x 16mm WAFER-TEK 20mm HORIZONTAL CAVITY BATTEN

PRE-FINISHED NON-PERFORATEDCLOSURE FLASHING WITH 10° FALL

3-5m

m V

ENTI

LATI

ON

GAP

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

MIN

. 50m

m L

AP

SEPERATE BATTEN AND FLASHINGAS REQUIRED WITH DPC

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

BOTTOM OF CLADDING (FLUSH)

18 / 212018

PERMEABLE WALL UNDERLAY OVERFLASHING, SHOWN DASHED

METALCRAFT ESPAN™ VERTICALCLADDING

METALCRAFT ESPAN™ CLIP SYSTEMWITH 12G x 16mm WAFER-TEK

PRE-FINISHED NON-PERFORATEDCLOSURE FLASHING WITH 10° FALL

INTERNAL WALL LINING

PRE-PRIMED SKIRTING

CONCRETE SLAB

CAVITY CLOSER AS REQUIRED TONZBC

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

20mm HORIZONTAL CAVITY BATTEN

3-5m

m V

ENTI

LATI

ON

GAP

MIN

. 50m

m L

APM

IN. 7

5mm

CO

VER

ALTERNATIVE OPTION

6mm GAP

SEPERATE BATTEN AND CLADDING ASREQUIRED WITH DPC

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet 1 : 2

BOTTOM OF CLADDING (RECESSED)

19 / 212018

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet

3D WINDOW FLASHINGS

20 / 212018

RECESSED WINDOW FLASHINGS

HEAD FLASHING

JAMB FLASHING

SILL FLASHING

ALUMINIUMWINDOWJOINERY

METALCRAFTESPAN™ VERTICALCLADDING

LIP OF DISCHARGE AT LOWEST POINTOF ROOF

DOWNPIPE

OVERFLOW BELOW OPENING LEVEL, 1.5 xCROSS-SECTION AREA OF DOWNPIPE

METALCRAFT ESPAN™ VERTICALCLADDING

OPENING200mm MIN

EITHER SIDE

50mm MIN

OPE

NIN

G

75m

m M

IN

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDING

CVEP

Espan 340 / 470™

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

ScaleDate Sheet

3D RAINWATER HEAD

21 / 212018