dumper cycle study
TRANSCRIPT
![Page 1: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/1.jpg)
PREPARED BY:MOUSOM SINGHA
B.E MINING ENGINEERINGIIEST SHIBPUR
MAY, 2016
Study of Dumper Cycle Time
Katamati Iron Ore Mine
![Page 2: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/2.jpg)
Objective and Targets
Objective: To optimize dumper cycle time
Targets: To observe and collect data sample To analyse current level of dumper efficiency To identify means for improving cycle time
![Page 3: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/3.jpg)
Dumper – Shovel Mining System
Costs 50 – 60% of the total mining costs
![Page 4: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/4.jpg)
Standard Time Definition
![Page 5: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/5.jpg)
Factors affecting Dumper efficiency
Truck-shovel match and allocation;
Shift operating schedules;
Haul road design and ramp gradients ;
Haul road rolling resistance ;
Cycle Time.
![Page 6: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/6.jpg)
Cycle Time Study
The following factors were considered for the study: Waiting at the face Positioning Loading Travel(loaded); from face to dump Waiting at the dump Unloading Travel(empty); from dump to face Waiting at weigh bridge Weighing time
![Page 7: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/7.jpg)
Cycle Time Study
The following data were also collected, though not directly related to dumper cycle: Weight of load in dumper Maximum and minimum speeds of dumpers
![Page 8: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/8.jpg)
Cycle Time Study
It has been observed that two different kinds of ore based on their composition were mined simultaneously at the Katamati mine.
The two different ores were dumped at two different dump sites, namely, the Wet plant facility and the DCMP dump.
Hence, the cycle time study has been conducted separately for the two different dump sites.
![Page 9: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/9.jpg)
For Wet Plant Dump
Average total waiting time: 4.13 minutes
Average positioning time: 1 minute
Average loading time: 5.07 minutes
Travel time (loaded): 8.92 minutes
Travel time(empty): 9.35 minutes
![Page 10: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/10.jpg)
For Wet Plant Dump
Average weighing time: 1.50 minutes
Average unloading time: 1.78 minute
Average observed cycle time: 32.35 minutes
![Page 11: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/11.jpg)
For Wet Plant Dump
Time Breakdown
Waiting at faceWaiting at dumpWaiting at wt. bridgeWeighingPositioningTravel(empty)Travel(loaded)LoadingUnloading
![Page 12: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/12.jpg)
For DCMP Dump
Average total waiting time: 7.35 minutes
Average positioning time: 1 minute
Average loading time: 3.5 minutes
Travel time (loaded): 9.64 minutes
Travel time(empty): 8.85 minutes
![Page 13: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/13.jpg)
For DCMP Dump
Average weighing time: 1 minute
Average unloading time: 0.78 minute
Average observed cycle time: 32.42 minutes
![Page 14: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/14.jpg)
For DCMP Dump
Time Breakdown
Waiting at faceWaiting at dumpWaiting at wt. bridgeWeighingPositioningTravel(empty)Travel(loaded)LoadingUnloading
![Page 15: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/15.jpg)
Other Data
Average travel time from OK line to face at start of shift: 6 minutes
Average lead distance: 5 km
Average weighted maximum speed: 36.21 km/hr
Average load carried: 95.72 T
Average number of swings of shovel: 9
![Page 16: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/16.jpg)
Analysis
It is observable that the cycle time for both the dumps are almost identical; this can be owed to the fact that the distance covered by the dumpers are almost same – an average lead distance of 5kms from face to either of the plants.
Waiting time exceptionally long at DCMP; an average of 6 minutes
The number of operators is the same as that of dumpers; hence an absence of operators translates to a dumper being idle for the whole shift
![Page 17: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/17.jpg)
Analysis
In one shift, shovel servicing was not completed during the preceding 1 hour of break time and 3 dumpers had to wait in queue for 10 minutes for the servicing
Even though the maximum speed allowed is 30 km/hr, the rule is often broken. This behaviour is more pronounced as the shift progresses. This can be attributed to fatigue of operators and consequent disregard of rules.
![Page 18: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/18.jpg)
Analysis
In some cases, there is a dilemma of safety versus pressure of production. In a certain case, a dumper overtook a water-sprinkling truck even though over-taking is banned on the haul roads.
The DCMP breaks down often. In some cases, dumpers wait for a few minutes before they are finally instructed to dump near the DCMP and move along. This wait time can be reduced if DCMP informs the dumpers on time.
![Page 19: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/19.jpg)
Recommendations
More operators should be employed in a shift, even as standby. Often, an absence of a single operator leads to a dumper being idle for the whole shift further resulting loss in production.
Starting time for shifts should be aimed towards a staggered format. This means that shifts for different operators should start at different times so that “bunching” effect is avoided whereby a total of about 1 hour of idle time is experienced at the start and end of the shift. Similarly time is lost during the break time.
![Page 20: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/20.jpg)
Recommendations
Swarm-based truck-shovel dispatch system¹ or efficient Fleet Management Systems(FMS) like TALPAC, CAT FPC etc. should be installed.
¹Bissiri Y., Dunbar S., Hall A., Swarm –Based Truck-Shovel Dispatching System in Open Pit Mine Operations, Department of Mining and Mineral Process Engineering, University of British Columbia, Vancouver, Canada
![Page 21: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/21.jpg)
Recommendations
Both side loading should be aimed. A sample schematic is given for example in the following slides:
![Page 22: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/22.jpg)
![Page 23: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/23.jpg)
![Page 24: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/24.jpg)
Recommendations
All dumpers should be fitted with equipment checking the speed to prevent going above 30 km/hr, instead of only 1 dumper as is the case presently. However, since all observed dumpers cross this limit, further safety studies should be carried out to consider the possibility of raising this limit marginally, if regulations permit.
![Page 25: Dumper Cycle Study](https://reader033.vdocuments.mx/reader033/viewer/2022061602/5873a0321a28ab85438b757f/html5/thumbnails/25.jpg)
Thank you