G R E E N H O U S E S GRANDIO
®
GREENHOUSE USER MANUAL© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved
April 15, 2016 Manual Edition Extendable Greenhouses
GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KIT MANUALINCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION
Grandio Elite 8x24 Shown In Image
STOPThis manual is for
8x12, 8x16, 8x20 & 8x24.
If building an 8x8 with no extensions refer to
that manual.
G R E E N H O U S E S GRANDIO
®
Before you begin, take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual on pages 68-78. The base kit parts list is at the front on page 12 and 13. The back door transformation kit parts list is on page 78.
Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and white film side faces inside green-house. Panels may scratch easily so be careful what you clean them with.
Plan out when and where you are going to place the greenhouse, we recom-mend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.
Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day, plan to complete assembly in one day. Damage caused by incomplete assembly is not covered by warranty.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!
Save this owner’s manual for future reference and if you need our help.
CONTACT OUR CUSTOMER SERVICE DEPARTMENT at: 1-866-448-8231
Hours: 8:30a.m.-5:00p.m. Monday through Friday (Mountain Standard Time)
Backyard Living Source9543 W. Emerald St., Suite 101
Boise, ID 83704www.grandiogreenhouses.com
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY
Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choos-ing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come.
Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.
Cheers!Grandio Greenhouses
1
IMPORTANT! SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instruc-tions and identify all parts using the hardware identifier and parts list on pages 68-78. Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.
CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective �lm adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners.
• Each of the polycarbonate panels have a clear �lm side that should always face the sun, and a white �lm side which faces inside. The clear side has a UV coating and we recommend marking a small “x” on a corner of each panel to determine which side has the UV Coating as you cannot visually determine with your eye in the case of future disassembly.
• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.
• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.
• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.
• If using a ladder during assembly, use extreme caution.
• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a �rm and level base. If not properly installed warranty may be void.
NEEDED FOR ASSEMBLY • Tape Measure • 2 Step Ladders • Safety Glasses• Level • Work Gloves • Drill • Carpenter Square • Permanent Marker • Folding Utility Table• At Least 2 Adults • Masking Tape • Silicone Caulk
GRANDIO
T I PWhen you see this icon
pay special attention to
the helpful tips we have provided that will
make installation more e�cient.
2
G R E E N H O U S E S GRANDIO
®
ASSEMBLY INSTRUCTION STEPS
PREPARE FOR ASSEMBLY
STEP ONE: BASE ASSEMBLY
STEP TWO: FRONT ASSEMBLY
STEP THREE: BACK ASSEMBLY
STEP FOUR: MIDDLE ASSEMBLY
STEP FIVE: EXTENSION ASSEMBLY
STEP SIX: DOOR ASSEMBLY
STEP SEVEN: INTERIOR ROOF SUPPORTS
3
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Elite Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Wall Assembly....................................................21-26Back Wall Assembly.....................................................27-32Middle Assembly.........................................................33-38Extension Assembly...................................................39-458x20 and 8x24 Extension Assembly.....................46-50Extension Assembly Continued.............................51-60Door Assembly.............................................................61-66Interior Roof Supports.....................................................67GRA-ELI-8A Parts List.................................................68-70GRA-ELI-8P Parts List........................................................71GRA-ELI-4X Parts List.................................................72-74GRA-ELI-8XA Parts List..............................................75-76GRA-ELI-8XP Parts List....................................................77GRA-ELI-BD Parts List......................................................78Warranty..............................................................................79
PREPARE FOR GREENHOUSE ASSEMBLY
4
8X12 GRANDIO ELITE BARN STYLE GREENHOUSE DIMENSIONS
143 3/4”3652 mm
8X12
LEFT SIDE
*SEE BASE KIT ASSEMBLY SECTION FOR ALL GREENHOUSE BASE DIMENSIONS ON PAGES 14-17.
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Elite Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Wall Assembly....................................................21-26Back Wall Assembly.....................................................27-32Middle Assembly.........................................................33-38Extension Assembly...................................................39-458x20 and 8x24 Extension Assembly.....................46-50Extension Assembly Continued.............................51-60Door Assembly.............................................................61-66Interior Roof Supports.....................................................67GRA-ELI-8A Parts List.................................................68-70GRA-ELI-8P Parts List........................................................71GRA-ELI-4X Parts List.................................................72-74GRA-ELI-8XA Parts List..............................................75-76GRA-ELI-8XP Parts List....................................................77GRA-ELI-BD Parts List......................................................78Warranty..............................................................................79
Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchor-ing options are acceptable, based on wind and ground conditions in your area.
Pre-read pages 11-20 for base kit assembly informa-tion.
Go to www.grandiogreenhouses.com for founda-tion ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together.
Transparent Clear Film
Opal White Film
Polycarbonate Panels
Sun
The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.
IMPORTANT: POLYCARBONATE PANELS
IMPORTANT: BASE KIT ASSEMBLY & GREENHOUSE PLACEMENT
97 7/16”2475 mm
44”1117.6 mm
RO
OF
PE
AK
HE
IGH
T
95 5/16”2421 mm
BASE 3 1/4”82.6 mm
1 3/4” 44.4mmGUTTERS
61”1549.4 mm
EA
VE
HE
IGH
T
DO
OR
HE
IGH
T
74”1879.6 mm
EXTENSION KIT BOX CONFIGURATIONS
GRA-ELI-8P
Elite 8’x8’
GRA-ELI-8A
+
Aluminum Extrusions, Hardware Bag, Front,
Back and Doors.
8x8 Base Kit
GRA-BAS-8
Polycarbonate Panels
Base kit & hardware
+
Elite 8’x8’
GRA-ELI-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ELI-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Elite 8’ Extension
GRA-ELI-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ELITE 8X16
GRA-ELI-8XPPolycarbonate Panels For The 8’ Extension
+
Elite 8’x8’
GRA-ELI-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ELI-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Elite 8’ Extension
GRA-ELI-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ELITE 8X20
GRA-ELI-8XPPolycarbonate Panels For The 8’ Extension
Elite 4’ Extension
GRA-ELI-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-
ate Panels for 4’ Extension.
+ +
Elite 8’x8’
GRA-ELI-8AAluminum Extrusions, Hardware Bag, Front,
Back and Doors.
GRA-ELI-8PPolycarbonate Panels
8x8 Base Kit
GRA-BAS-8Base kit & hardware
Elite 8’ Extension
GRA-ELI-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRANDIO ELITE 8X24
GRA-ELI-8PPolycarbonate Panels For The 8’ Extension
+
Elite 8’ Extension
GRA-ELI-8XA
Aluminum Extrusions, Hardware Bag, 8’ Base
Extension, 2 Roof Vents, 2 Snow Load Extension Supports.
GRA-ELI-8XPPolycarbonate Panels For The 8’ Extension
Elite 4’ Extension
GRA-ELI-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-
ate Panels for 4’ Extension.
Fron
t
Back
Fron
t
Back
Fron
t
Back
Fron
t
Back
5
We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site.*See the reference diagrams on pages 6-10 for more information about how the parts will go together and what makes up each section for the assembly. If building a back door you will follow the instructions in the manual, the parts for the transformation are in box GRA-ELI-BD.
GRANDIO ELITE 8X12
BACK
FRONT
620
LEFT SIDE RIGHT SIDE
6
603C
L08D
603D
601B
601B
620 604-R601A-FL 601A-FR
601B
601B
619
L08D
603C
603E
602C
602D 602D
601B
601B 601B
601B
L08B-X
601A-B
L08B
603C603C
601A-B
L08B-X
622 622
604-L
602A
602A
602A
602A
602A
602A
602B
602B
602B
602B
602B602B
609609 609
609
607
L21
610610
630 630
610610
630630
601A-B601A-B
601A-FL 601A-FR
L08A-X L08A-X
L08C-X
L08C-X
609 609610 630 609 609
610630
L08A
622-L 622-R
603C 603C
L08C-X
603C/616618
603C/616618
L08C-X
623B623B
623A 623A
606-WS606-WS Y7
Y7
Y7
Y7
Y7
Y7
Y7
Y7
Y8
Y8
Y8
Y11Y9 Y10 Y10 Y9
Y8
Y8
Y8
Y11
Y11
Y11
Y11
Y11
Y11
Y11
Y3-1 Y3-2
Y2-2Y2-1
Y6 Y6
Y6 Y6Y1 Y1
Y1 Y1Y1 Y1
Y4-1Y4-2Y5-1Y5-2
Outside View
DIAGRAM SHOWS THE ASSEMBLED(8’x8’ BASIC CONFIGURATION)
(GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8) 8x8 ELITE KIT INCLUDES, FRONT,
BACK, BASE AND SIDES.
BA-S2BA-S2
BA-S1
BA-S1
606-WS
606-WS
606-WS
606-WS
606-WS
606-WS
606-WS 606-WS
606-WS 606-WS606-WS 606-WS
7
BA-S
2
BA
CK
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
FRO
NT
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
620
LEF
T S
IDE
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ELI
-8A
and
GR
A-E
LI-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
603CL0
8D
603D
601B
601B
620
604-
R
601A
-FL
601A
-FR
601B
601B
L08D
603C
603E60
2C
602D
602D
601B
601B
601B
601B
L08B
-X
601A
-B
L08B
603C
603C
601A
-B
L08B
-X
622
622
604-
L
602A
602A
602A
602A
602A
602A
602B
602B
602B
602B
602B
602B
609
609
609
609
L21
610
610
630
630
610
610
630
630
L08M
-X
L08C
-X
609
609
610
630
609
609
610
630
622-
L62
2-R
603C
603C
L08C
-X
603C
/616
618
603C
/616
618
L08M
-X
623B
623B62
3A62
3A
606-
WS
606-
WS
Y7 Y7 Y7 Y7
Y7 Y7 Y7 Y7
Y8
Y8
Y8
Y11
Y9Y1
0Y1
0Y9
Y8 Y8
Y8
Y11Y1
1
Y11
Y11
Y11
Y11 Y1
1
Y3-1
Y3-2
Y2-2
Y2-1
Y6Y6
Y6Y6
Y1Y1
Y1Y1
Y1Y1 Y4-1
Y4-2
Y5-1
Y5-2
8x8 Elite Side
Outside View
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11Y1
1
602A
602A
602B 60
2B
Y7Y7
Y11Y1
1
Y8Y8
4X Elite Side
BA-S
2
607
607
BA-S
5
602B 602B
602B
602B
602B
602B
602B
602B60
2B
602B
609
630
609
610
609
609
610
630
(4’ Extension Side) (GRA-ELI-4X)Elite 4’ Side Extension
Includes Base
L08C
-XL0
8C-X
AZ1
AZ1
L08E
-X
L08D
-X
L08E
-XL0
8D-X
L08E
-XL0
8D-X
L08D
-XL0
8E-X
L08D
-XL0
8E-XL08E
-XL0
8D-X
L08A
BA-S
1
619
BA-S
1
(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8) 8x8 Elite Includes Front, Back, Base, and Sides
DIAGRAM SHOWS THE ASSEMBLED 8X12 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS A 4 FOOT EXTENSION KIT
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
L08A
-XL0
8A-X
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
BA-S
2
606-
WS
620
603CL0
8D
603D
601B
601B
620
604-
R60
1A-F
L60
1A-F
R
601B
601B
619
L08D
603C
603E60
2C
602D
602D
601B
601B
601B
601B
601A
-B
L08B
603C
603C
601A
-B
622
622
604-
L
602A
602A
602A
602A
602A
602A
602B
602B
602B
602B
602B
602B
609
609
609
609
L21
610
610
630
630
610
610
630
630
L08M
-X
L08C
-X
609
609
610
630
609
609
610
630
L08A
622-
L62
2-R
603C
603C
L08C
-X
603C
/616
618
603C
/616
618
L08M
-X
623B
623B62
3A62
3A
Y7 Y7 Y7 Y7
Y7 Y7 Y7 Y7
Y8
Y8
Y8
Y11
Y9Y1
0Y1
0Y9
Y8 Y8
Y8
Y11
Y11 Y1
1
Y11
Y11
Y11 Y1
1
Y3-1
Y3-2
Y2-2
Y2-1
Y6Y6
Y6Y6
Y1Y1
Y1Y1
Y1Y1 Y4-1
Y4-2
Y5-1
Y5-2
8x8 Elite Side(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8)
8x8 Elite Includes Front, Back, Base, and Sides
Outside View
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11
Y11
602A
602A
602B 60
2B
Y7Y7
Y11
Y11
Y8Y8
(8’ Extension Side) 8X Elite Side
BA-S
260
7
607
BA-S
3
BA-S
4
602B
602B
602B
602B
602B
602B
602B602B
609
630
609
610
609
609
610
630
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP) Elite 8’ Side Extension includes Base
L08C
-XL0
8C-X
AZ1
AZ1
L08E
-X
L08D
-X
L08E
-XL0
8D-X
L08E
-XL0
8D-X
L08D
-XL0
8E-X
L08D
-XL0
8E-XL08E
-XL0
8D-X
602B
602B
602A
602B
602A
602B
Y8Y7
Y8
Y7
Y11
Y11
602B
602B
602B
602A
602A
Y11
Y11
603C
/616
618 Y1
0Y9
602B
Y7Y7
BA-S
1
BA-S
1
BA
CK
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
FRO
NT
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ELI
-8A
and
GR
A-E
LI-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
DIAGRAM SHOWS THE ASSEMBLED 8X16 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT EXTENSION KIT
8
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
L08B
-XL0
8B-X
606-
WS
606-
WS
606-
WS
606-
WS
L08A
-XL0
8A-X
606-
WS
606-
WS
610
BA-S
262
0
603CL0
8D
603D
601B
601B
620
604-
R60
1A-F
L60
1A-F
R
601B
601B
619
L08D
603C
603E60
2C
602D
602D
601B
601B
601B
601B
L08B
-X60
1A-B
L08B
603C
603C
601A
-BL0
8B-X
622
622
604-
L
602A
602A
602A
602A
602A
602A
602B
602B
602B
602B
602B
602B
609
609
609
609
L21
610
610
630
630
610
610
630
630
L08A
-XL0
8A-X
L08M
-X
L08C
-X
609
609
610
630
609
609
610
630
L08A
622-
L62
2-R
603C
603C
L08C
-X
603C
/616
618
603C
/616
618
L08M
-X
623B
623B62
3A62
3A
Y7 Y7 Y7 Y7
Y7 Y7 Y7 Y7
Y8
Y8
Y8
Y11
Y9Y1
0Y1
0Y9
Y8 Y8
Y8
Y11
Y11 Y1
1
Y11
Y11
Y11 Y1
1
Y3-1
Y3-2
Y2-2
Y2-1
Y6Y6
Y6Y6
Y1Y1
Y1Y1
Y1Y1 Y4-1
Y4-2
Y5-1
Y5-2
8x8 Elite Side(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8)
8x8 Elite Includes Front, Back, Base, and Sides
Outside View
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11
Y11
602A
602A
602B 60
2B
Y7Y7
Y11
Y11
Y8Y8
(8’ Extension Side) 8X Elite Side
BA-S
2
607
607
BA-S
3
BA-S
4
602B
602B
602B
602B
602B
602B
602B60
2B
609
630
609
610
609
609
610
630
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP) Elite 8’ Side Extension includes Base
L08M
-XL0
8M-X
AZ1
AZ1
L08E
-X
L08D
-X
L08E
-XL0
8D-X
L08E
-XL0
8D-X
L08D
-XL0
8E-X
L08D
-XL0
8E-XL08E
-XL0
8D-X
602B
602B
602A
602B
602A
602B
Y8Y7
Y8
Y7
Y11
Y11
602B
602B
602B
602A
602A
Y11
Y11
603C
/616
618 Y1
0Y9
602B
Y7Y7
BA-S
1
BA-S
1
BA
CK
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
FRO
NT
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ELI
-8A
and
GR
A-E
LI-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
607
DIAGRAM SHOWS THE ASSEMBLED 8X20 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11Y1
1
602A
602A
602B 60
2B
Y7Y7
Y11Y1
1
Y8Y8
(4’ Extensions Side) 4X Elite Side
BA-S
5
BA-S
660
2B 602B
602B
602B
609
630
609
610
609
609
610
630
(4’ Extension Side) (GRA-ELI-4X)Elite 4’ Side Extension
Includes Base
L08C
-XL0
8C-X
AZ1
AZ1
L08E
-XL0
8D-X
L08D
-XL0
8E-X
9
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
BA-S
262
0
603CL0
8D
603D
601B
601B
620
604-
R60
1A-F
L60
1A-F
R
601B
601B
619
L08D
603C
603E60
2C
602D
602D
601B
601B
601B
601B
L08B
-X60
1A-B
L08B
603C
603C
601A
-B
L08B
-X
622
622
604-
L
602A
602A
602A
602A
602A
602A
602B
602B
602B
602B
602B
602B
609
609
609
609
L21
610
610
630
630
610
610
630
630
L08A
-XL0
8A-X
L08M
-X
L08C
-X
609
609
610
630
609
609
610
630
L08A
622-
L62
2-R
603C
603C
L08C
-X
603C
/616
618
603C
/616
618
L08M
-X
623B
623B62
3A62
3A
Y7 Y7 Y7 Y7
Y7 Y7 Y7 Y7
Y8
Y8
Y8
Y11
Y9Y1
0Y1
0Y9
Y8 Y8
Y8
Y11
Y11 Y1
1
Y11
Y11
Y11 Y1
1
Y3-1
Y3-2
Y2-2
Y2-1
Y6Y6
Y6Y6
Y1Y1
Y1Y1
Y1Y1 Y4-1
Y4-2
Y5-1
Y5-2
8x8 Elite Side(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8)
8x8 Elite Includes Front, Back, Base, and Sides
Outside View
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11
Y11
602A
602A
602B 60
2B
Y7Y7
Y11
Y11
Y8Y8
(8’ Extension Side) 8X Elite Side
BA-S
2
607
607
BA-S
3
BA-S
4
602B
602B
602B
602B
602B
602B
602B602B
609
630
609
610
609
609
610
630
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP) Elite 8’ Side Extension includes Base
L08M
-XL0
8M-X
AZ1
AZ1
L08E
-X
L08D
-X
L08E
-XL0
8D-X
L08E
-XL0
8D-X
L08D
-XL0
8E-X
L08D
-XL0
8E-XL08E
-XL0
8D-X
602B
602B
602A
602B
602A
602B
Y8Y7
Y8
Y7
Y11
Y11
602B
602B
602B
602A
602A
Y11
Y11
603C
/616
618 Y1
0Y9
602B
Y7Y7
BA-S
1
BA-S
1
BA
CK
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
FRO
NT
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
LEF
T S
IDE
In b
oxes
GR
A-E
LI-8
A a
nd G
RA
-ELI
-8P,
th
e b
ase
for
8x8
is a
ll in
GR
A-B
AS
-8.
RIG
HT
SID
EIn
box
es G
RA
-ELI
-8A
and
GR
A-E
LI-8
P,
the
bas
e fo
r 8x
8 is
all
in G
RA
-BA
S-8
.
602A
602A
602B
602B
603C
/616
618
Y7Y7
Y9Y1
0
Y8
Y11
Y11
602A
602A
602B 60
2B
Y7Y7
Y11
Y11
Y8Y8
(8’ Extension Side) 8X Elite Side
BA-S
3
BA-S
4
602B
602B
609
630
609
610
609
609
610
630
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP) Elite 8’ Side Extension includes Base
L08C
-XL0
8C-X
AZ1
AZ1
L08E
-XL0
8D-X
L08D
-XL0
8E-X
602B
602B
602A
602B
602A
602B
Y8Y7
Y8
Y7
Y11
Y11
602B
602B
602B
602A
602A
Y11
Y11
603C
/616
618 Y1
0Y9
602B
Y7Y7
607
DIAGRAM SHOWS THE ASSEMBLED 8X24 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS (2) 8 FOOT EXTENSION KITS
10
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
606-
WS
BASE KIT ASSEMBLY INSTRUCTIONS
11
Pre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure.
Be sure the orientation will allow for proper drainage in and around your greenhouse.
It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.
The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all.
Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your greenhouse in keeping the temperature up inside.
Extreme Wind Conditions: If you live in a windy location there is no way to build a 100% storm safe greenhouse, but there are a number of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condi-tion areas where wind is constant and extreme.
See our website GrandioGreenhouses.com for Extreme Weather Anchoring Kits and Moisture Control Kits to aid in protecting your green-house in the event of harsh weather conditions prior to beginning installation.
It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants and keeping the temperature and air circulation to the max e�ciency.
You will need to choose an anchoring system prior to installation, see our website for options: www.GrandioGreenhouses.com
For Cement Base Installation: We recommend you use wedge style concrete anchoring bolts to secure your structure.
For Deck Base Installation: We recommend you use anchoring bolts to secure your structure.
For Earth Installation: We recommend you use the BA-A1 / L-BOLT anchoring system, and bury corner posts into the ground and seal into place with quickrete.
12
PAR
TS
LIST
FO
R B
ASE
KIT
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Elite Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Wall Assembly....................................................21-26Back Wall Assembly.....................................................27-32Middle Assembly.........................................................33-38Extension Assembly...................................................39-458x20 and 8x24 Extension Assembly.....................46-50Extension Assembly Continued.............................51-60Door Assembly.............................................................61-66Interior Roof Supports.....................................................67GRA-ELI-8A Parts List.................................................68-70GRA-ELI-8P Parts List........................................................71GRA-ELI-4X Parts List.................................................72-74GRA-ELI-8XA Parts List..............................................75-76GRA-ELI-8XP Parts List....................................................77GRA-ELI-BD Parts List......................................................78Warranty..............................................................................79
BA-S5
BA-S6
BA-C4
BA-S10
BA-S03
ML01
46 3/4 in / 1187 mm
46 3/4 in / 1187 mm
8 7/16 in / 214 mm
1/2 x 3/4
M6*14
NUT
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
2
2
16
16
BA-S1
BA-S2
BA-C3
BA-S03
ML01
W05
97 3/8 in / 2474 mm
94/4 in / 2394 mm
5 7/16 in 138 mm
M6*14
NUT
CLIPS
8X8 BASE KIT PARTS WILL BE FOUND IN (GRA-BAS-8) BOX
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
2
4
28
28
9
BASE KIT PARTS LIST PARTS WILL BE FOUND IN (GRA-ELI-4X) BOX
FOR THE 4’ EXTENSION BASE KIT
BASE KIT PARTS LIST
13
PAR
TS LIST
FOR
BA
SE K
IT
Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Elite Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Wall Assembly....................................................21-26Back Wall Assembly.....................................................27-32Middle Assembly.........................................................33-38Extension Assembly...................................................39-458x20 and 8x24 Extension Assembly.....................46-50Extension Assembly Continued.............................51-60Door Assembly.............................................................61-66Interior Roof Supports.....................................................67GRA-ELI-8A Parts List.................................................68-70GRA-ELI-8P Parts List........................................................71GRA-ELI-4X Parts List.................................................72-74GRA-ELI-8XA Parts List..............................................75-76GRA-ELI-8XP Parts List....................................................77GRA-ELI-BD Parts List......................................................78Warranty..............................................................................79
BA-S3
BA-S4
BA-C4
BA-S10
BA-S03
ML01
93 7/16 in / 2374 mm
93 7/16 in / 2374 mm
8 7/16 in /214 mm
1/2 X 3/4
M6*14
NUT
PARTS WILL BE FOUND IN (GRA-ELI-8XA) BOXFOR THE 8’ EXTENSION BASE KIT
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
2
2
16
16
BA-S1
BA-S2
BA-S1
BA-S2
BA-C3
BA-C3
BA-C3
1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.2 Attach the BA-S2 to the BA-S5 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S6 and the BA-S2. Go to page 18 for the next step.
BA-S5BA-S6
BA-C3
8x12 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-4X)
BA-C4
BA-C4
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
BA-C4
BA-S5 BA-S2
BA-S03ML01
14
STE
P O
NE
BA-S10
BA-S10143 3/4” / 3652 mm
97 7/16” / 2475 mm
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
BA-S2
BA-S1
BA-S2
BA-C3
BA-C3
BA-C4
BA-S3
BA-S4
BA-C3
BA-C4
1.3 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1 See diagram . 1.4 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2. Go to page 18 for the next step.
8x16 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA)
BA-C3
15
STE
P O
NE
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
190 15/16” / 4849 mm
97 7/16” /
2475 mm
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S2BA-S2
BA-C3
BA-C3
BA-S3
BA-S4
BA-C3
BA-C4
BA-C3
BA-C4
BA-S5
BA-S6
1.5 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.6 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03. See . Repeat for other side connecting the BA-S4 and the BA-S2, then BA-S3 to BA-S5 and BA-S4 to BA-S6. Go to page 18 for the next step.
8x20 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA) AND (GRA-ELI-4X)
HOLE FOR ANCHOR
16
STE
P O
NE
BA-C4
BA-S5 BA-S2
BA-S03BA-M03
BA-C4BA-S10
BA-S10
BA-C4BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
237 5/8” / 6036 mm
97 7/16”
/ 2475 m
m
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
BA-S1
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
BA-S1
BA-S2
BA-S1
BA-S2
BA-C3
BA-C3
BA-S3BA-S4
BA-C3
BA-C4
BA-C3
BA-S4 BA-S3
8x24 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA) AND (GRA-ELI-8XA)
1.7 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1. The BA-S3 will attach to the other BA-S3 and BA-S4 will attach to the other BA-S4 See diagram . 1.8 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01.See . Repeat for other side connecting the BA-S4 and the BA-S2, and then the BA-S3 to the BA-S3, and then the BA-S4 to the BA-S4. Go to page 18 for the next step.
17
STE
P O
NE
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-C4BA-S10
BA-S10
BA-C4BA-S10
BA-S10
GRANDIO
T I PNote that the holes for screws on the base kit
sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .
BA-C4 284 3/8”/ 7223 mm
97 7/16”
/ 2475 m
m
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
HOLE FOR ANCHOR
18
STE
P O
NE
1.9 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 Bolt and ML01 Collard Nut combo, tighten the collard nut on the inside of the base kit using the 10mm wrench. Repeat this process on all corners. See and . Note: BA-S1 will be the front and back, while the BA-S2’ s will be the sides of your greenhouse base.
1.10 For Ground Installation only Insert the BA-S03 and the BA-A1 into the holes at the bottom side of the corners of the base, the nut will be tightened on the inside of base, see and . Locate the anchoring devices for your installation needs and follow the directions for that anchoring system. If you have not purchased an anchoring system please go to www.GrandioGreenhouses.com for anchoring kit options.
BASE KIT ASSEMBLY INSTRUCTIONS
BA-S1
BA-S2
FRONT
SIDE
BA-C3
BA-S03ML01
BA-C3
BA-S1
BA-S2
BA-S03
ML01 Collared Nut
BA-S03
ML01 Collared Nut
BA-S03
BA-C4
BA-S3 BA-S2
BA-S03ML01
BA-S10
HOLE FOR ANCHOR
HOLE FOR ANCHOR
OutdoorGround
Assembly
1.11 If using an L-Bolt / BA-A1 anchoring kit the BA-A1 must be buried in ground. See .Dig holes to bury the BA-A1’s, you determine size and depth for your location. We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package.See www.GrandioGreenhouses.com for anchoring kit options.
BASE KIT GROUND INSTALLATION
BA-S2
BA-A1
BA-S1
BA-S03 BA-A1 * Must be inserted into the ground, and secured with concrete.
GRANDIO
T I PMake sure base is squared and level before setting
anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides.
**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
19
STE
P O
NE
20
STE
P O
NE
1.12 Holes are present in base kit for anchoring bolts see and . You determine and acquire proper fastener prior to installation for your surface. Discard the BA-S10 for deck or concrete slab installation.See www.GrandioGreenhouses.com for anchoring kit options.
Use lag boltor concrete anchors
to attach base. (Fasteners not included).
B
Deck or Patio
Assembly
Use an appropriate fastener to attach to your surface through these access holes.
BA-C4
BA-S6 BA-S2
BA-S03ML01
BA-S1
BA-C3
BA-S2
HOLE FOR ANCHORBOLT OR SCREW.
BASE KIT DECK INSTALLATION**BASE MUST BE LEVEL & SQUARE,
FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
GRANDIO
T I PMake sure base is squared and level before setting
anchors. Use a measuring tape to ensure all corners are the same. Use level on all four sides.
If surface is uneven you may wantto purchase large washers that will fit under the base and allow fasteners to go through to use as a shim for leveling the base kit.
FRONT FRAME ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE FRONT HORIZONTAL
This picture shows the inside view of front section fully assembled.All parts for front assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
We recommend that you assemble the front on a tarp.* If you purchased the Back Door Transformation kit you will repeat this section for your
back wall using parts found in GRA-ELI-BD , GRA-ELI-8A and GRA-ELI-8P boxes.If you want to purchase the Back Door Transformation kit call 1-866-448-8231.
GRANDIO
T I PLay �at on ground to assemble the front frame of
your greenhouse. If possible try to �nd a shady area protected from the wind. Panels can burn grass and plants if in direct light.
GRANDIO
T I PWe recommend watching our how to assembly videos
with tricks and tips for easier assembly and installation of your Grandio Greenhouse at: www.grandiogreenhouses.com
603C
L08D
603D
601B
601B
604-L601A-FR 601A-FL
601B
601B
619
L08D
603C
603E
604-R
Y3-1Y3-2
Y1 Y1
Y2-2 Y2-1
L08A-X L08A-XGRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
606-WS 606-WS
21
STE
P T
WO
Inside View
WG02 WG02
WG02WG02
22
STE
P T
WO
2.1 Prethread all S05 screws into the WG01 and WG02’s for ease of installation, see only turn S05 a few turns. Leave the mid hole open, as this is for the end cap attachment.
2.2 Use WG01 bracket to attach the (2) 601B’s together with the 603E, secure parts with the S05 screws provided see . The WG01 will slide into the groove of the 601B’s, and also slide into the groove of the 603E, screw head will remain outside chan-nel.
2.3 Install WG02’s into (2) 601B’s then tighten S05 screws when extrusions are completely tight see . Note: the fat end of the WG02 will always be on the bottom side see .
GRANDIO
T I PPRETHREAD SCREWS TIP: Locate all WG01, WG02,
and S05 screws, pre thread these to make installation easier. Note that the fat end on the WG02 will always face downward.
Inside View
601B
601B 601B
601B
603E
WG01
WG01601B601B
S05
WG02
601B
603E
WG01
FAT END
FAT END
IMPORTANT: Use only S05 Screws, other screws may damage frame.
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
WG02 WG02
WG02 WG02
2.4 Insert polycarbonate panels Y3-2 and Y3-1 into place as shown in .
2.5 Attach 603E and 603D with W04 and S04/ML01 fasteners as shown in . 2.6 Attach the 603D to the 601B’s using the W04-1’s with the S04/ML01 fasteners on both sides as shown in .
Y3-1Y3-2
601B
601B 601B
601B
603E
WG01
WG02WG02
603D W04W04-1 W04-1
S04ML01W04 603E
603DW04-1 603D
601B
GRANDIO
T I PBOLT INSTALLATION TIP: Locate ML01/S04 nuts and
screws, loosely pre thread into the W04 and W04-1’s and place in the groove of the extrusion to make installation easier.
W04 W04-1
Inside View
23
STE
P T
WO
Transparent Clear Film
Opal White Film
Polycarbonate Panels
Sun
The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.
IMPORTANT: POLYCARBONATE PANELS
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
*IF USING THE MOISTURE CONTROL KIT YOU WILL USE IT NOW
2.7 View diagrams and attach the (2) 604’s and (2) 601A’s to the 619. Note the orientation of the 604’s, there are 4 di�erent 601A’s (2) for the front and (2) for the back with di�erent hole placements. The large holes should be at the top and facing forward on the front frame assembly. See diagram on this page. The 601-FR and the 601-FL will have a hole at the top side and will face forward.
shows where the corner pieces attach to 619. shows where the door frame attaches to the 619.
*If assemblling the back door you will need to drill 1/4” holes in 601A-B’s to match the front wall, these holes should face the ground during assembly.
GRANDIO
T I PMake sure the hole on the 601A-FL and 601A-FR
face to the front of greenhouse for future install of the L21 and L28 bracket that holds the door header in place.
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
601A-FL601A-FR
604-R 604-L
619
INSIDE
OUTSIDE
INSIDE OUTSIDE
INSIDE
OUTSIDEOUTSIDE
INSIDE
Inside View
24
STE
P T
WO
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
TIP: If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track.
S04
ML01
604-R
619INSIDE DOOR FRAME
A
S04
601A-FR
ML01619
INSIDE Inside View
Polycarbonate panel
606-WS619
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
Inside View
Y1 Y1
604-L604-R
619 606-WS
606-WS
601A-FL601A-FR
OUTSIDE
2.8 Attach 606-WS to 619, this will hold the polycarbonate panels in place. If it seems too tight slide �ngers or nut driver along edges, gently stretching the 606-WS to allow room for panels to �t .
2.9 Insert Y1 polycarbonate panels into place, make sure Y1’s slide completely into 606-WS as shown in .
2.10 Set (2) 603C’s atop the Y1 panels, then attach (2) L08D’s to the 603C’s, 601A’s and 604’s using S04/ML01 fasteners, make sure it is snug with the tops of the Y1 panels, then tighten fasteners. See .
2.11 Insert the Y2-2 and Y2-1 polycarbonate panels as shown in .
S04/ML01
603CL08D
601A604 603C
L08D
604-L 601A-FL601A-FR
L08D
603C
604-RY1 Y1
Y2-2 Y2-1
601A-FR 604-R603C
L08D
25
STE
P T
WO
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
2.12 Move roof and front section together and align the WG02’s into the 601A’s, and the W04-2’s into the 604’s. Insure a snug �t between the WG02’s, 601B’s and 601A’s and then tighten the S05 screws as shown in . Tighten the W04-2’s with the S04 /ML01 nut and bolt as shown in .
2.13 Attach the L08A-X to L08D and 604 to square front section loosen S04/ML01 attached to the bottom of the (2) 604’s, square the frame with carpenter square or use a measuring tape to make sure corner mea-surements are the same, also check distance across from the top of 601A’s, and also to the bottom of the 601A’s across, make sure distance is the same. Tighten L08A-X’s to hold squareness as shown in . 603C
L08D
604-R
601A-FL601A-FR
619
603C
604-L
Y1 Y1
Y2-2 Y2-1L08D
Y3-1Y3-2
601B 601B
Inside View
W04-2W04-2WG02 WG02
S05
L08A-X L08A-X
W04-2
604
603D
S04ML01
WG02
Fat EndUP
Profile View
L08A-X
601A-FLS04ML01
603D
603C L08D
WG02 601B
S05 601A-FR
S05
26
STE
P T
WO
FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL
WG02WG02
This image shows the inside view of the back wall assembly.All parts for back assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
We recommend that you assemble the back wall on a tarp.* If you are using the Back Door Transformation Kit you will skip this section.
BACK ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE BACK HORIZONTAL
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
Inside View
GRANDIO
T I PMake sure the UV coated side of the panel faces
outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
SunWG01
L08B
603C603C
602C602D 602D
603C 603C
601A601A
L08B-X L08B-X
L08A
601B601B
601B
601B
601B
WG02 WG02
606-WS
Y1 Y1Y1 Y1
Y4-1Y5-1Y5-2
Y4-2
WG02
606-WS
27
STE
P T
HR
EE
WG02
28
STE
P T
HR
EE
3.1 Prethread all S05 screws into the WG01 and WG02, see . Leave mid hole open it is for endcap attachment.
3.2 Use the WG01 bracket to attach the (2) 601B’s together, secure parts by sliding the WG01 into the 601B’s as shown in diagram .
3.3 Install WG02’s to connect (2) 601B’s when �rmly placed between the extru-sions tighten the S05 screws, see .
Inside View601B
601B 601B
601BWG01
GRANDIO
T I PPRETHREAD SCREWS TIP: Locate all WG01, WG02,
and S05 screws, loosely pre thread these to make installation easier. Note that the fat end on the WG02 will always face down.
WG01601B601B
S05
WG02WG01
FAT END
FAT END
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
IMPORTANT: Be careful moving or you may bend bracket.
WG02
28
STE
P T
HR
EE601B
601B
WG02
WG02 WG02
Y1Y1Y1Y1
601A-B601A-B
L08A
602C602D 602D
3.4 Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram .
Attach (2) 602D’s to L08A using S04/ML01 fasteners as shown in diagram .
Attach 602C to L08A using S04/ML01 fastener as shown in diagram .
3.5 Attach the (4) 606-WS’s to the L08A as shown in .
3.6 Insert the Y1 polycarbonate panels into the grooves of 601A, 602D and 602C. Make sure Y1 panels are inserted into 606-WS as shown in . You may need to use a screwdriver to gently open the 606-WS to �t the polycarbonate panels into the groove of 606-WS.
606-WS606-WS 606-WS606-WS
29
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
ML01
601A
L08A
S04 INSIDE
602D
L08AINSIDE
ML01
S04
602C
L08A
Polycarbonate Panel
606-WSL08A
Y1Y1Y1Y1
601A-B601A-B602C
602D 602D
Y4-1Y5-1Y5-2
Y4-2
3.7 Set (4) 603C’s atop each Y-1 panel, then align the pre threaded S04-ML01 fasteners in each 603C to the L08B and to each 601A-B, 602D and the 602C. When aligned tighten the middle �rst and work your way outward. See diagrams , , .
3.8 Insert the Y5-1 and Y5-2 polycarbonate panels into place. Then insert the Y4-1 and Y4-2 into place as shown in the diagram.
603CL08B
602DS04
ML01
L08B
601A-B
Inside View
L08B 603C603C603C603C
603C 603C
L08B602C
603C
602D
L08B
30
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
Inside View
3.9 Pre thread the S05 screws on WG01, WG02’s and the S04/ML01 on W04-2’s brackets and place into appropriate extrusion see , and . Align WG02’s into 601A’s, the W04-2’s into 602D’s, and the WG01 into the 602C. When all members are snug tighten all fasteners to lock into place.
Y1Y1Y1Y1
601A-B601A-B
602C
602D 602D
Y4-1Y5-1Y5-2
Y4-2
601B601B
601B
601B
601B
W04-2 W04-2
WG02
WG01
GRANDIO
T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre
thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
31
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
601A-B
601B
WG02
WG02
WG02WG02
3.10 A. Attach (2) L08B-X’s to (2) 602D’s and L08A with S04/ML01 as shown in .
B. Attach (2) L08B-X’s to the (2) 601A-B’s with fasteners as shown in .
GRANDIO
T I PSquare by loosening bolts attached to the tops of the
L08B-X, use measuring tape to make sure corner to corner measures the same.
ML01 S04
602D
L08B-X L08A
Inside View
602C602D 602D
601A-B601A-B
L08B-X L08B-X
601A-B
S04/ML01
L08B-X
32
STE
P T
HR
EE
BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL
1
MIDDLE ASSEMBLY INSTRUCTIONS
4.1 We recommend pre threading all (9) W05 clips with the nut and bolt combos now. See , note the bolt head will always slide into the extru-sion, W05 clips will be used in step 4.5.
4.2 With no less than 2 people place the pre assembled front section on top of the base kit front. Have person (1) hold the front vertically while the other attaches the front section 601A’s to the base using S04/ML01 fasteners as shown in .Person (1) must continue to hold up the front wall!
GRANDIO
T I PYou will need a minimum of (2) people to complete the
middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
Warning: The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.
33
STE
P F
OU
R
BA-S1
BA-S2
BA-S1
601A
601A604
BA-S5
BA-S6
BA-S2
601A
ML01S04
Inside ViewFront Right side
BA-S1F
2
**This Base shows a 8x12, your greenhouse may be longer and configured of more base kit pieces.
If building a greenhouse with a front and back door you will repeat steps 4.1-4.5 for attaching both front and back walls of the greenhouse. ML01/
NUT
S04 BOLTW05CLIP
34
STE
P F
OU
R
MIDDLE ASSEMBLY CONTINUED
601A
601B
L08A-X
L08C-X L08D
L08C-X
Base
4.3 Attach L08C-X to 601A and the BA-S2 with S04/ML01 on both sides as shown in and with the nut and bolt combos.4.4 Attach the front section 619 to the base using (3) S10/ML02 fasteners as shown in , then attach the threshold support 619-BAR to the inside of the 619 with (5) S19 self tapping screws included in the package, see .
2
1
BA-S1
604
601A
601A
619 Attaches to the base kit with S10/ML02
619-BAR will attach with the (5) S19screws
1
4.5 Have person (1) continue to hold the front vertically while the other attaches the font section to the base with W05/S04/ML01 fasteners as shown in , and . The (4) W05 clips will catch the under edge of the front base kit and then slide upward attaching to the bottom of the 601A’s and the 604’s. To do this you will slide the bolt into the extrusion, slide it down to catch the edge of the base kit, then slide up and hold up as high as it will go and then tighten the ML01 nut, note you will have to switch out the combo that was originally used to the W05 Clip. If you are having a tough time using the ML01 �anged nuts in the corners, you may switch out to the ML02 nuts without the �anged edge instead.
If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall.
MIDDLE ASSEMBLY CONTINUED
BA-S1
604
601A
601A
2
BA-S2
BA-S1BA-S5
BA-S6
35
STE
P F
OU
R
BaseBA-S1
W05619
Inside
BA-S2
601AML01S04
Inside View
W05
BA-S1
ML01 S04
L08A-X 619
604-R
W05
MIDDLE ASSEMBLY CONTINUED
4.6 Attach back wall 601A’s with back base corners using S04/ML01 on both sides as shown in .
4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in . Attach the L08C-X to the 601A as shown in , make sure the S04/ML01 combos are tight.
4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A’s meet the corner of the base as shown in , and where 602D’s, and the 602C meet the BA-S1B see . Then use W05 Clip combos to attach the corner 601A’s to the base kit as shown in , you will have to switch out the combo that was originally used to the W05 Clip.
601A
601B
L08B-X
L08C-X L08B
W05
Base
602C, 602D
Outside
Inside
L08C-X
L08C-X
602D 602D
602C
36
STE
P F
OU
R
BA-S2 orBA-S6
601A
ML01S04
Inside ViewBack Left side
L08C-X
Base
Back Wall BA-S1601AML01S04
BA-S2 orBA-S6
Inside View
W05
Back Base
Back Base
If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then skip ahead to step 4.9.
BA-S1
L08C-X
Repeat these steps if you are building an 8x20 or 8x24 with your last extension box, note it is best to connect 8x8, then 8X, then a 4X if assembling an 8x20. Note that the notches shown in should be spaced every 2 feet, none should be right next to each other.
4.9 Attach the 607 to 607 extension with the 607-XS and the (4) S08 screws provided see , . The S08 screws are to be installed on the inside as shown in diagram . Wait to tighten the screws all at one time when both sections are aligned correctly, apply even pressure while tightening.
4.10 Apply a bead of silicone to the seam where the 607’s meet and to the holes where the S06 screws will attach the DP01 to the 607 ridge. See . Immediately align the DP01 apply a small amount of silicone to the holes on the exterior of DP01 then insert the S06 screws.
607
607607-XS
APPLY SILICONE CAULKTO RIDGE AND HOLES
S06
For 8x20 and 8x24 Grandio Elite Assembly
MIDDLE ASSEMBLY CONTINUED
37
STE
P F
OU
R
607-XS
607
607
DP01
FRONT
DP01607
607
FRONT
S06
S08
WARNING
Notches
Notches
MIDDLE ASSEMBLY CONTINUED
607
607
601B 601B
Inside View
Side Angle View
607
601B 601B
Inside View
S04/ML01
4.11 With 2 people, attach the ridge to front and back by sliding into place as shown in and , using S04/ML01 fasteners attach the 607 to the 601B’s. See for how the �nal orientation should be.
607
38
STE
P F
OU
R
601B
601B
EXTENSION ASSEMBLY INSTRUCTIONS
Warning: You will need a minimum of 2 people to complete this section, you will not be able to stop assembly until page 45. Note that if you are assembling an 8x20 or an 8x24 greenhouse you will proceed thru the 2nd extension assembly instruc-tions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier.
GRANDIO
T I PBOLT INSTALLATION TIP: Locate about 30 nuts and
bolts and pre thread for easiest installation.
Warning: This section will take about 30 minutes so be prepared to �nish as there is not a stopping point until page 45 for an 8x12 or 8x16 Greenhouse, or for an 8x20 or 8x24 Greenhouse page 50. Note it may be helpful to have a few more people at this point the more the merrier.
39
STE
P F
IVE
L08M-X
L08M-X
W14 BRACKET5.1 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.
5.2 Attach the 602A to the base with a nut and bolt combo where the extension kits meet on the base kit, with other person holding the 602A in place. Measure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .
5.3 Attach (2) L08D-X’s to the 602A and to the base using the ML01/S04 Combos. See and .
BA-S2BA-S2
L08D-X
Measure 6”
Measure 6”
BASE
L08D-X
602A
6”
W14
602A
L08M-X W14
602A
L08D-XL08M-X
602AL08D-X
607
EXTENSION ASSEMBLY INSTRUCTIONS
40
STE
P F
IVE
Back
IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN
Back
Front
5.4 Attach the 609-XS to 609 with the (2) S09 screws provided see . The S09 screws are to be installed from the outside of the 609, see .
Pay special attention to the orientation of the 609, make sure the correct side faces down, see .
609
Profile View
Groove 609
609-XS
S09
609-XS
FRONT
EXTENSION ASSEMBLY INSTRUCTIONS
41
STE
P F
IVE
FRONT
UP
UP
UP
OUTSIDE VIEW
INSIDE VIEW
5.5 With 2 people proceed to install 609 in this order, note that 609 must be installed with groove side down see .
1. With one person holding the 609 level and in position have the other person loosen the top of the L08C-X and let it fall free, attach the 609 to the 601B using S04/ML01 (nut and bolt). See and .
2. Now move the loosened S04/ML01 (nut and bolt) currently attached to the L08C-X upward to secure the 609, 601A-F and L08C-X together as shown in .
3. Have assistant keep holding at the middle section . Turn to next page for detailed installation.
L08D L08C-X601A
LOOSENML01
Inside View
GRANDIO
T I PYou will need a minimum of (2) people to complete the
middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
1
2
EXTENSION ASSEMBLY INSTRUCTIONS
42
STE
P F
IVE
L08B
L08D
L08C-X601A
601A
601A
601AL08C-X
L08C-X
L08C-X
L08D
601B
601B
601B
UP
601B
609
Profile View
Groove
601A
Note the line on the 609 that shows the exact placement of the 601B’s and the 601A’s when installedcorrectly.
601B
609
S04/ML01
L08C-XL08D
Inside View
601A
43
STE
P F
IVE
609609
602A
NOTE EXACT PLACEMENT OF THE 602A TO THE 609.
EXACTPLACEMENT LINE FOR 602A
4. Note the top of 602A should touch the line on the 609 for exact placement, see . Attach the 609 to the 602A with the S04/ML01 nut and bolt combos see diagram .
5. Repeat steps 1-4 on the other side see .
602A
609609-XS
S04/ML01
602A
FRONT
FRONT
EXTENSION ASSEMBLY INSTRUCTIONS
602A
OUTSIDE VIEW
INSIDE VIEW
44
STE
P F
IVE
5.6 Moving up to the midroof 609, with person 1 holding the 609 in place person 2 will attach the 609 to the front of the greenhouse to the 601B’s, see . Person 1 will continue holding the 609.5.7 Person 2 will attach the 602B to the 609’s see . Attach one more 602B between the 609 and 607, see .Repeat on the other side of greenhouse.
1
2
609
609
602B
607 Roof Line
609
Outside View
Inside View
602B
609
607
EXACT PLACEMENT
602A
FRONT
EXTENSION ASSEMBLY INSTRUCTIONS
Inside View
609
ML01/S04
601B
601B
609
602B
602B
ML01/S04
609-XS
FRONT
FRONT
607 Roof Line
** 8x16 Elite Shown
45
STE
P F
IVE
609
609
602B607
609
602A
BZ-1
AZ-1
1
2
5.8 With two people attach the AZ-1 to W17 and the base and the lower 602A, see . Next attach the upper end to the mid roof line touching the 609 see for exact placement. Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo. 5.9 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s. Note the exact placement of the edge of the BZ-1 should touch the top edge of the 609 see .
601B
601B
AZ-1
S04ML01
BZ-1
S02ML01
609
609-XSIF YOUR GREENHOUSE IS AN 8X12 OR 8X16 SKIP TO PAGE 51. IF YOURS IS AN 8X20 OR 8X24 PROCEED ON TO THE NEXT PAGE.
EXTENSION ASSEMBLY INSTRUCTIONS
AFTER COMPLETING STEP 5.9
** 8x16 Elite Shown
UP Front
602A
AZ-1
S02/ML01
INSIDE VIEW
W17 BRACKET
S02/ML01You will need to switch this bolt out to an S02
FRONT
AZ-1
ML01W17 BracketNote orientationof bracket
S02
(7mm gap edge will fitdown into base bottom)
10mm7mm
1
5.10 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.
5.11 Attach the 602A to the base with a nut and bolt comboMeasure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .
5.12 Attach (2) of the L08D-X supports to the 602A and to the base using the ML01/S04 Combos. See and .
BA-S2L08D-X
BASE
L08D-X
602A
6”
W14
Measure 6”
L08M-X
602A
L08D-X
Measure 6”602A
L08D-X
L08M-XL08M-X
W14 BRACKET
602AL08M-X W14
46
STE
P F
IVE
2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
Back
IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN
Back
Front
5.13 Attach the 609-XS to 609 with the (2) S09 screws provided see . The S09 screws are to be installed from the outside of the 609, see .
Pay special attention to the orientation of the 609, make sure the correct side faces down, see .
609
Profile View
Groove
47
STE
P F
IVE
2nd EXTENSION ASSEMBLY INSTRUCTIONS
OUTSIDE VIEW
INSIDE VIEW
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
609
609-XS
S09
609-XS
FRONT
FRONT
UP
UP
UP
1
1
609-XS
609609-XS
609-XS
2
609-8X-L609
S09609-XS
GAP FOR SCREWS
609-XS
5.14 With 2 people proceed to install 609 extension at the eave or lower mid roof in this order.
1. With one person holding the 609 level and in position have the other person attach the 609 to other end of the 609-XS as shown in .
2. With one person holding the 609 level and in position have the other person attach the 609 to the 602A using S04/ML01. See .
3. Repeat steps 1. and 2. on other side of the greenhouse.
609609-XS
609-8X-L
609-XS
609
602A
NOTE EXACT PLACEMENT OF THE 602A TO THE 609.
EXACTPLACEMENT LINE FOR 602A
FRONT
FRONT
48
STE
P F
IVE
2nd EXTENSION ASSEMBLY INSTRUCTIONS
2
1
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
UP
609-8X-R
1
609-8X-L
1
2
5.15 With person 1 holding the 609 in place person 2 will attach the 609 to the 609-XS with the (2) S09’s screws to the upper mid roof see . Person 1 will continue holding the 609.5.16 Person 2 will attach the 602B to the two 609’s with (2) S04/ML01 (nuts and bolts) see . Attach one more 602B between the 609 and 607 with (2) S04/ML01 (nuts and bolts), see .Repeat both steps on the other side of greenhouse.
Outside View
602B
609
607
EXACT PLACEMENT
2
609-8X-L609
S09609-XS
GAP FOR SCREWS
FRONT
49
STE
P F
IVE
602B
2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
FRONT
Inside View
609
602B
602B
ML01/S04
609-XS
FRONT 607 Roof Line
609-8X-R
2
5.17 With two people attach the AZ-1 to W17 with the base and the lower 602A, see . Then attach the upper end to the mid roof line touching the 609 see for exact placement. Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.
5.18 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s. Note the exact placement of the edge of the BZ-1 should touch the top edge of the 609 see .
601B
601B
AZ-1
S04ML01BZ-1
S02ML01
609
609-XS
BZ-1
AZ-1
1
609609
602B
50
STE
P F
IVE
2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
FRONT
602A
AZ-1
S02/ML01
INSIDE VIEW
W17 BRACKET
S02/ML01You will need to switch this bolt out to an S02
FRONT
AZ-1
ML01W17 BracketNote orientationof bracket
S02
(7mm gap edge will fitdown into base bottom)
10mm7mm
2
2
609
607
609
1
602A
609 609-XS
ML01/S04
609-8X-L
5.19 With two people attach the 609 extension to 609-XS with the (2) S09 screws provided see and .
5.20 With person 2 still holding in place have person 1 loosen the L08C-X nut and bolt combo, allow to fall out of place, then align the 609 into place with the 601B and 601A, see . Use a S04/ML01 combo to attach the 609 to the 601B, then slide the nut and bolt combo attached to the L08C-X into place to secure the 609 between the 601A and the L08C-X.
Repeat these steps on other side of the greenhouse, and then mid roof line see .
609-8X-L609
S09 609-XS
609
601BML01/S04
FRONT
FRONT
MIDDLE BACK ASSEMBLY INSTRUCTIONS
51
STE
P F
IVE
601B
601B
601A-B
609-8X-L
OUTSIDE VIEW
INSIDE VIEW
INSIDE VIEW601B
609
S04/ML01
L08C-XL08B
Inside View
601A
* Note Notch Placement: Notches will have about a 23” space between notches, notches will not be right next to each other when attaching the extension 609.
5.21 Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the ML01 (nut) attached to the L08C-X and the base. See diagram . Remove and set aside the L08D-X supports.
1. Once the bottom of one L08C-X is loosened set the 602A onto the bolt of the L08C-X. Be sure the 602A is aligned and sitting �ush on top of the base kit. See for reference.
2. Hold the 602A in place and attach the top of the 602A to the 609 using S04/ML01 (nut and bolt). As shown in .
3. Repeat steps 1. and 2. on all four corners where the L08C-X ‘s meet the base kit.
4. Now attach the bottom of 602A to the Base using a S04/ML01 (nut and bolt) as shown in , and to the 609 with an S04/ML01 combo as is shown in .
5. Repeat step 4. on all places where a 602A should go. You may reference diagrams at front for your exact size.
Note: Where the L08C-X reattaches to the BASE and the 602A be sure to secure them tightly see .
L08C-X
602A
L08C-XS04ML01BASE
Inside View
609
602A
Inside View
BA-S2
602A
Inside View
ML01/S04ML01/S04
L08C-X
52
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
L08D-X
L08D-X
602A
602A602A 602A
602A
Loosen only one L08C-X at a time.
Slide L08C-X
into place
5.22 Install only the upper roof line 602B’s between the 607 and the 609 along the entire upper roof line with S04/ML01 (nut and bolt). See and . Repeat on other side of roof section.
Do Not attach lower roof 602B’s yet, they will get in your way when installing the upper roof panels and roof vents.
ML01S04
609
602B
Outside View
602B
609
607
EXACT PLACEMENT
609
607
53
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
TOP
TOP
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
602B
Roof Line
5.23 Insert Y11 panels to upper roof section then slide the 630 into the groove of the upper 609 as shown to hold Y11’s in place. See and . Note that you may need to loosen the bottoms of some of the 602B’s to slide the 630’s into place as the �t is very tight. Check that all nut and bolt combos are tightened again after installation of 630’s. Note that there is a 630 in the extension box(s), make sure you install so the screw holes on the 630’s align for the DP03 to attach. Once the 630’s are aligned apply a streak of silicone to the seam of the 630’s, then align the DP03 with the holes and a�x into place with the S06 screws provided. See .
Y11
Y11Y11
Y11Y11 Y11
630
609
630601B
601B609
630601B
601B609
630
609
Left Profile View Right Profile View
607
609
602B
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
54
STE
P F
IVE
602B602B
602B602B
APPLY SILICONE CAULKTO RIDGE AND HOLES
DP03
S06630-4X-R
Right Side of GreenhouseIs Shown in Image
FRONT BACK
601B
601B
601B
601B
630
630-4X-L
The two profiles should be flush at ends when installed correctly.
The two profiles should be flush at ends when installed correctly.
SUN
616 615PC sheet
5.24 Assemble the roof window vents as shown below in and , using the Z02 screws attach the 615, 616, and 618’s with the Y10 panel as shown, be careful not to strip the screw heads. Pay attention to the Y10 panel, as the stickers must face the sun.
5.25 Insert assembled window into the end of the ridge of 630 and slide into position. See . Window positions are your discretion however, may not be placed nearest the front or back as you will need a 602B support to keep in window vent in place, and may not be right next to another vent. Place directly across from each other for best cross draft ventilation, see for optional placement.
**It is recommended to apply silicone caulk to the exterior seams on the bottom and sides of each panel, where panels meet the frame for water resistance, or see the Moisture Control Kit on our website to maintain panel clarity. The interior and top of each panel is protected so it is recommended that you leave them un-caulked allowing the panels to breathe.
GRANDIO
T I PPlace roof windows in desired location before
attaching all 602B’s. Note the 8x12 has 3 windows, an 8x16 has 4 windows, an 8x20 has 5 windows and an 8x24 has 6 windows.
Y10
Y10
Y10
SUN
Y10
618
Z02
Z02
Z02
Z02
Z02618
ScrewdriverOutside View
Roof VentPlacement
Inside of window
615
616
618616
Z02
Note Correct Orientation
630
55
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED630
Inside
Roof Vent
602B
602B
Y10
Y10
Polycarbonate Panel
606BASE
Outside
5.26 Attach all remaining 602B’s between the 609’s, after all roof vents are positioned see .
5.27 Install plastic strip 606-WS before inserting polycarbonate sheet Y7’s, see .
5.28 After Y7’s are installed on both sides, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is plumb. The top edges of Y7’s will align when greenhouse is level or plumb.
Y11Y11
Y11
Y11
Y11
Y11
606-WS
Outside View
602B
609
607
EXACT PLACEMENT
602A
602A
56
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
5.29 To ensure there is no gap in roof vent position 603C as shown in . Connect 603C to middle of 602B’s using W04 bracket as shown in .
5.30 Attach HQC01 to 616 with the Z04 screws see , close roof vent and attach the handle onto HQC02 middle pin (the �rst two holes of the handle to the second and third pins of HQC02). Then attach HQC02 into 603C’s track with S04/ML01 (nuts and bolts), see .
603C
618
616
616
603C
616
Z04
HQC02
Y10
Y10
HQC01Handle
Y10603C
Inside view of 603C603C
602BW04
Note: If you are installing automatic roof vent openers follow those directions for correct installation.SAVE MANUAL HARDWARE FOR WINTER SWITCHOUT.
HQC01Handle
57
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
HQC01Handle
603C
HQC02
HQC01Handle
ML01/S04
Inside View
1 2 3
Y10
Y10
Y11Y11
Y11
Y11
Y11
5.31 Remove the L08M-X support combo, take apart and install on the sides of the AZ1 extension brace, as shown in . Save the hardware and W14 bracket for possible future use or hang inside as a plant hanger clip.
5.32 Insert polycarbonate sheets Y8’s and Y9’s into the lower roof of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown in the diagram once the panels are in place.
5.33 Slide 610 Gutters into 609’s groove as shown in diagram . Repeat on both sides. Note the orientation of the gutters, the extension gutters will be at the back and the holes should align with gutter down spout hole see next page.
Y11
L08M-X
L08C-X
L08C-X
L08M-X
601B
601A
610
609
609
610
Gutter
Outside View
Y8Y9
Y8
Y8
Y9
58
STE
P F
IVE
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
AZ1
The two profiles should be flush at ends when installed correctly.
TAPE
59
STE
P F
IVE
DP02B
DP02
610-8X-L
610
5.34 Apply a small amount of the silicone caulk to the seam where the 610 gutters meet, then attach the DP02 on the inside of the gutter and the DP02B will slide under the gutter and will rest above the 602A. Apply silicone to the holes where the S07 screws will attach the 610 gutters to the DP02 and DP02B. Note the DP02B has pre-tapped holes to accept the screws and hold tight. See diagram and .
Repeat these steps to assemble the additional set(s) for both sides of your greenhouse.Remove the tape from the panels you may have used to hold in place.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
DP01
610
610
602A
602B
60
STE
P F
IVE
JG03A Z03
JG02A
JG01
JG03B
Z03
JG02B
4.25 Attach JG01, JG02A, JG02B, JG03A and JG03B end caps to the ridge, midroof and gutters on both front and back as shown below. Use Z03 screws to attach the JG03A and JG03B endcaps along with the silicone adhesive. Use Z06 screws to fasten end caps through the WG01 and WG02 as shown in images. Note you may want to seal into place with silicone caulk on the inner side and around the edges.
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
Exterior view of mid roof cap JG01.
Z06
Interior greenhouse view of mid roof cap, where Z06 screw goes through WG01 mid hole into the end cap.
DOOR ASSEMBLY DIAGRAM
Z01622
Y6
Y6
622-R
UP
UP
Catch
620Z01
Z01
Z01
Z01
Z01
623B
623A622Side View
622
J08A
BottomView
623B
620
623A
J08A
J08A
622-R
UP
UP
Side View
622
J08A
BottomView
Inside View
This image shows the inside view of Right Door Assembly.All parts for door assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
Use the #2 head Phillips Screw Driver for installation.If you are using the Back Door Transformation kit you will repeat steps 6.1-6.11 to install the Back Door,
these parts will be found in box GRA-ELI-BD.
61
STE
P S
IX
623B
623A
622
J08A
BottomView
J08A
We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orienta-tion of what is inside verses outside and how the doors will hang on page 63-67. Make sure window panels face the right direction to the sun and note that the panels may have predrilled holes for the handles to attach later and these need to be aligned with the lock mechanisms, if you do not see any holes you will need to drill the holes out before installing the door handles. Be careful not to strip the phillips heads when assembling. 6.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .6.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .6.3 Insert Y6 windows into position as shown in .
623B
Z01
620Z01
Z01623B
623A
622 620
623A
622
620
Y6
Y6
GRANDIO
T I P Transparent Clear FilmOutside Greenhouse
Opal White FilmInside Greenhouse
Polycarbonate Panel
Sun
622
UP
UP
Side View
Inside View
62
STE
P S
IX
DOOR ASSEMBLY
You may need to gently open the channel with a flat head screwdriver if screws are not going into place with ease.
FLUSHALIGNWITH TOP
J08A
622
J08A
BottomView
Side ViewOf Top
* DoubleBall Catch
on the 622-L
622-L
UP
UP
Side ViewOf Bottom
6.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see .6.5 Attach the 622-L to the 623B, 623A and 620 using the Z01 screws as shown in .6.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball and catch match up so doors will latch closed and slide properly .
Y6
Y6
623B
623A
620
622-R
Catch
Z01
Z01
Z01
622-R
Side ViewOf Top
* Catch on the 622-R
622-R
UP
UP
Side ViewOf Bottom
* Note the orientation of the 622-L and 622-R. Also make sure the right side is facing out on the Y6 polycarbonate panels.
Inside View622
DOOR ASSEMBLY CONTINUED
63
STE
P S
IX
DOOR INSTALLATION
64
STE
P S
IX
S02
L21
603D
6.7 Slide the (2) S02 bolts down the track of the L21 see , align with the holes on the 603D door header. With one person inside the greenhouse line up hanging door track L21 with door header 603D, move bolts on L21 to line up with bolt holes on door header 603D. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will now center on the front of the greenhouse and tighten the S02/ML01 combo.
1
2
Side Profile View of L21 Hanging Track
Inside View
Track
S02SCREW
S04 S04S02
6.8 Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle.
6.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and .**We included some felt dots in your Grandio Welcome Kit, please apply to the inside bottom edge of the 623B as shown in , these felt dots will make your doors �t snug and slide smoothly.
DOOR INSTALLATION
Outside View Inside View
Top
Bottom
Side Profile View of Hanging Track
L21 L21
622-HNDL
622-HNDLNUT/BOLT
622-HNDL
622-HNDLNUT/BOLT
65
STE
P S
IX
623B623B
6.10 Attach L28 to L21 with S04/ML01, and L28 to 601A with WASHER and S02/ML01 as shown below in diagram and . Check that the L21 and L28’s are square. Attach (2) J07 to the ends of L21 see . The L28 should align square to the 601A.
6.11 Check that the door locks are snug, you may adjust them with screwdriver if needed as they can be tightened or loosened.
DOOR INSTALLATION
601A
S02
L28
601A-FR
601A-FL
66
STE
P S
IX
Top Profile View
J07L21
L28
S02
601A
ML01 WASHER
Backside View
603D
L21
L28
S04/ML01
Top LeftProfile View
INTERIOR ROOF SUPPORT ASSEMBLY 7.1 Attach the L08E-X to the upper roof section as shown with S04/ML01 fasteners already in place where the 607 meets the 601B, and the 609 and the 602B meet see , repeat this on the front section of the greenhouse, and where extensions meet at the AZ-1.
7.2 Attach the L08D-X to the rear lower roof section where S04/ML01 fasteners are already in place where the 609 and the 602B meet, and the 609 and the 601B meet see , repeat on the front section, and where the extensions meet the AZ-1. 7.3 Attach the BZ-1’s to the roof line as shown in diagram with the S04/ML01. The edge of the BZ-1 should meet up to the edge of 609 exactly.
7.4 Use CZ-1’s to support the interior wall at the eave using the S04/ML01. See diagram . We suggest that you measure down 9” and mark it with a pencil so the base of the CZ-1 will meet there.
You may remove all stickers now with Goo Gone remover if needed.
L08E-X
L08D-XL08D-XCZ-1 CZ-1
BZ-1
9” 9”
L08D-X
L08E-X
BZ-1
CZ-1602B
607
609Roof Vent
602B
601B
601B
609
609
607
67
STE
P S
EV
EN
601B 601B
Congratulations You Did It!!
68
PAR
TS
LIST
FO
R G
RA
-ELI
-8A
601A-B
601A-FL
601A-FR
601B
602A
602B
602C
602D-R
602D-L
603C
603D
603E
619 PACK619-BAR
S19 SCREWS10 / ML02
604-R
604-L
607
606-WS
609
610
615
616
618
630
L08A
NOTE THESE ARE PACKED TOGETHER
L08B
56 9/16 in / 1437 mm BACK CORNERS
56 9/16 in / 1437 mm FRONT LEFT CORNER
56 9/16 in / 1437 mm FRONT RIGHT CORNER
29 7/16 in / 748 mm CORNER ROOF
56 9/16 in / 1437 mm
29 7/16 in / 748 mm
90 1/2 in / 2299 mm
83 1/4 in / 2115 mm
83 1/4 in / 2115 mm
21 7/8 in / 555 mm
72 3/16 in/ 1833 mm
18 1/4 in / 463 mm
94 1/4 in / 2394 mm44 1/2 / 1130
M4*10M6*16 / ML02
70 3/4 in / 1797 mm FRONT RIGHT
70 3/4 in / 1797 mm FRONT LEFT
94 1/4 in / 2394 mm
21 3/4 in / 553 mm
94 1/4 in / 2394 mm
94 3/8 in / 2397 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 11/16 in / 500 mm
94 3/8 in / 2397 mm
94 1/4 in / 2394 mm
94 1/4 in / 2394 mm
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST
GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
1
1
8
6
12
1
1
1
8
1
1
1 - 6191 - 619 Bar
5 - S19 Screws3 - S10 / ML02
1
1
1
14
4
2
2
2
4
2
1
1
69
PAR
TS
LIST
FO
R G
RA
-ELI
-8A
L08D
L08A-X
L08B-X
L08C-X
L08D-X
L08E-X
WG01
WG02
W04
W04-1
W04-2
Z01
Z02
24 3/16 in / 614 mm
52 1/4 in / 1327 mm
51 3/16 in / 1300 mm
61 1/32 in / 1550 mm
37 13/16 in / 960 mm
38 11/16 in / 957 mm
FRONT & BACK
FRONT & BACK
ROOF LINE
BACK WALL
CONNECTOR
M4*30SCREWS FOR DOORS
M4.6*16SCREWS FOR ROOF VENTS
AZ-1 / W17S02/ML01
S02/ML01
S04/ML01
S05
Z04, S04/ML01
HQC01
HQC02
L28 / WASHER
W11
W13
W16
BZ-1
CZ-1
86 1/4 in / 2190 mmEXTENSION SUPPORT
M6*25
M6*14
M6*10SCREWS FOR WG01 AND WG02
ROOF VENT HARDWARE
ROOF VENT ARM
ROOF VENT LATCH
19 9/16 in / 497 mm 4mm WASHERS
MULTI-DRIVER
10 MM NUT DRIVER
10 MM WRENCH
56 1/2 in / 1435 mm
23 5/8 in / 600 mm
2
2
2
4
4
4
2
8
5
2
4
13
9
2
6
150
45
4
2
2
2/2
1
1
1
3
6
GRAPHIC PART NAME SIZE/LOCATION QUANTITYGRAPHIC PART NAME SIZE/LOCATION QUANTITY
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST
70
PAR
TS
LIST
FO
R G
RA
-ELI
-8A
622-HNDL
622-HNDLNUT/BOLT
620
L21
J07
622
622-R
622-L
623A
623B
J08A
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
4
2
1
2
2
1
1
2
2
4
DOOR HANDLES
DOOR HARDWARE
21 7/16 in / 545 mm
95 1/2 in / 2425 mm
L21 END CAP
69 11/16 in / 1770 mm
69 11/16 in / 1770 mm
69 11/16 in / 1770 mm
21 7/16 in / 545 mm
21 7/16 in / 545 mm
DOORS
(GRA-ELI-8A) 8’x8’ GRANDIO ELITE ALUMINUM PACKING LIST
JG01
JG02 A/B
JG03 A/B
Z03
Z06
ML02
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
2
2/2
2/2
4
10
8
RIDGE END CAP
MID ROOF END CAP
GUTTER END CAP
M3*25
M4*10
NON FLANGED NUTS
71
PAR
TS
LIST
FO
R G
RA
-ELI
-8P
(GRA-ELI-8P) 8’x8’ ELITE PANEL BOX PACKING LIST
Y1
Y2-1
Y2-2
Y3-1
Y3-2
Y4-1
Y4-2
Y5-1
Y5-2
Y6
Y7
Y8
Y9
Y10
Y11
FRONT & BACK PANEL
FRONT PANEL
FRONT PANEL
FRONT PANEL
FRONT PANEL
BACK PANEL
BACK PANEL
BACK PANEL
BACK PANEL
DOOR PANEL
SIDE WALL PANEL
ROOF PANEL
UNDER ROOF VENT
ROOF VENT PANEL
ROOF PANEL
GRAPHIC NAME SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
6
1
1
1
1
1
1
1
1
4
8
6
2
2
8
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
35 1/2 in / 902 mm
35 1/2 in / 902 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
47 5/16 in / 1202 mm
9 1/16 in / 230 mm
23 in / 585 mm
9 15/16 in / 252 mm
19 1/8 in / 486 mm
9 1/16 in / 230 mm
35 3/16 in / 894 mm
35 7/16 in / 900 mm
42 13/16 in / 1087 mm
34 in / 864 mm
57 in / 1447 mm
30 5/8 in / 778 mm
8 7/8 in / 225 mm
19 1/8 in / 486 mm
30 3/8 in / 772 mm
23 in / 585 mm
9 1/16 in / 230 mm
19 1/8 in / 486 mm
9 15/16 in / 252 mm
35 3/16 in / 894 mm
9 1/16 in / 230 mm
42 13/16 in / 1087 mm
35 7/16 in / 900 mm
602A
602B
603C
L08M-X
L08D-X
L08E-X
607-4X
607-XS
DP01
609-4X-R609-4X-L
609-XS
DP03
606-WS
610-4X-R610-4X-L
DP02
DP02B
630-4X-R630-4X-L
615
616
618
BZ-1
CZ-1
Z02
S04 / ML01
S06
56 9/16 in / 1437 mm
29 7/16 in / 748 mm
21 7/8 in / 555 m
61 in / 1550 mm
37 13/16 in / 960 mm
37 11/16 in / 957 mm
46 3/4 in / 1187 mm
ROOF CONNECTOR
ROOF CONNECTOR
46 3/4 in / 1187 mm
EAVE CONNECTOR
630 CONNECTOR
21 3/4 in / 553 mm
46 3/4 in / 1187 mm
GUTTER BRACKET
GUTTER BRACKET
46 3/4 in / 1187 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 11/16 in / 500 mm
56 1/2 in / 1435 mmROOF SUPPORT
23 5/8 in / 600 mmEAVE SUPPORT
5X12 MMSCREWS FOR ROOF VENT
M6*14
4*10ATTACHES DP01 TO 607
GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY
4
8
1
2
2
2
1
1
1
4
4
2
4
2
2
2
2
1
1
2
2
2
5
50
3
72
PAR
TS
LIST
FO
R G
RA
-ELI
-4X
(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST
S07
S08
S09
W04
W14
HQC01
HQC02
Z04, S04/ML01
M5*8SCREW FOR DP02 AND DP02B
M6*16ATTACHES 607-XS TO 607
M4*6ATTACHES 609-XS TO 609
CONNECTOR FOR 603C
L08M-X BRACKET
ROOF VENT ARM
ROOF VENT LATCH
ROOF VENT HARDWARE
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
5
5
20
2
2
1
1
4 EACH
73
PAR
TS
LIST
FO
R G
RA
-ELI
-4X
(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST
74
PAR
TS
LIST
FO
R G
RA
-ELI
-4X
(GRA-ELI-4X) ELITE 4’ EXTENSION PANEL BOX PACKING LIST
Y7
Y8
Y9
Y10
Y11
SIDE WALL PANEL
ROOF PANEL
UNDER ROOF VENT
ROOF VENT PANEL
ROOF PANEL
GRAPHIC NAME SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
4
3
1
1
4
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
57 in / 1447 mm
30 5/8 in / 778 mm
8 7/8 in / 225 mm
19 1/8 in / 486 mm
30 3/8 in / 772 mm
602A
602B
603C
L08M-X
L08D-X
L08E-X
607-8X
607-XS
DP01
609-8X-R609-8X-L
609-XS
DP03
606-WS
610-8X-R610-8X-L
DP02
DP02B
630-8X-R630-8X-L
615
616
618
AZ-1 / W17S02/ML01
BZ-1
CZ-1
Z02
S04 / ML01
S06
56 9/16 in / 1437 mm
29 7/16 in / 748 mm
21 7/8 in / 555 m
61 in / 1550 mm
37 13/16 in / 960 mm
37 11/16 in / 957 mm
93 7/16 in / 2374 mm
ROOF CONNECTOR
ROOF CONNECTOR
93 7/16 in / 2374 mm
EAVE CONNECTOR
630 CONNECTOR CAP
21 3/4 in / 553 mm
93 7/16 in / 2374 mm
GUTTER BRACKET
GUTTER BRACKET
93 7/16 in / 2374 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
19 11/16 in / 500 mm
86 1/4 in / 2190 mmEXTENSION SUPPORT
56 1/2 in / 1435 mmROOF SUPPORTS
23 5/8 in / 600 mmEAVE SUPPORTS
M4.6*16SCREWS FOR ROOF VENTS
M6*14
M4*10ATTACHES DP01 TO 607
(GRA-ELI-8XA) ELITE 8’ EXTENSION ALUMINUM PACKING LIST
GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY
8
16
2
2
2
2
1
1
1
4
4
2
8
2
2
2
2
2
2
4
2
4
6
9
90
3
75
PAR
TS
LIST
FO
R G
RA
-ELI
-8X
A
S07
S08
S09
W04
W14
HQC01
HQC02
Z04, S04/ML01
M5*8SCREW FOR DP02 AND DP02B
M6*16ATTACHES 607-XS TO 607
M4*6ATTACHES 609-XS TO 609
CONNECTOR FOR 603C
L08M-X BRACKET
ROOF VENT ARM
ROOF VENT LATCH
ROOF VENT HARDWARE
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
5
5
20
4
2
2
2
4
(GRA-ELI-8XA) 8X GRANDIO ELITE ALUMINUM PACKING LIST
76
PAR
TS
LIST
FO
R G
RA
-ELI
-8X
A
77
PAR
TS
LIST
FO
R G
RA
-ELI
-8X
P
(GRA-ELI-8XP) GRANDIO ELITE 8 EXTENSION PANEL BOX PACKING LIST
Y7
Y8
Y9
Y10
Y11
SIDE WALL PANEL
ROOF PANEL
UNDER ROOF VENT
ROOF VENT PANEL
ROOF PANEL
GRAPHIC NAME SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY
8
6
2
2
8
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
22 3/4 in / 578 mm
57 in / 1447 mm
30 5/8 in / 778 mm
8 7/8 in / 225 mm
19 1/8 in / 486 mm
30 3/8 in / 772 mm
601A-B
601A-FL
601A-FR
601B
602A
602B
602C
602D-R
602D-L
603C
603D
603E
619 PACK619-BAR
S19 SCREWS10 / ML02
2
1
1
8
6
12
1
1
1
8
1
1
1 - 6191 - 619 Bar
5 - S19 Screws3 - S10 / ML02
72 3/16 in / 1833 mm BACK WALL
18 1/4 in / 463 mm BACK WALL
70 3/4 in / 1797 mm FRONT RIGHT DOOR
70 3/4 in / 1797 mm FRONT LEFT DOOR
24 3/16 in / 614 mm
94 1/4 in / 2394 mm44 1/2 in / 1130 mm
M4*10M6*16 / Nut
69 11/16 in / 1770 mm
69 11/16 in / 1770 mm
69 11/16 in / 1770 mm
21 7/16 in / 545 mm
21 7/16 in / 545 mm
21 7/16 in / 545 mm
52 1/4 in / 1327 mmCROSS SUPPORT
DOOR
DOOR HANDLES
(GRA-ELI-BD) GRANDIO ELITE BACKDOOR PACKING LIST
603D
603E
604R
604L
L08D
619619-BAR
S19 ScrewS10 / ML02
622
622-R
622-L
620
623A
623B
L08A-X
J08A
622-DOORHANDLES
Z01
S04/ML01
S02/ML01
L21
J07
L28 / WASHER
W04
W04-1
W04-2
Y3-1
Y3-2
Y2-1
Y2-2
Y6
1/4 DB
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
1
1
1
1
2
1 - 6191 - 619 Bar
5 - S19 Screws3 - S10 / ML02
2
1
1
2
2
2
2
4
4
GRAPHIC PART NAME SIZE/LOCATION QUANTITY
13
35
4
1
2
2/2
1
2
2
1
1
1
1
4
1
M4*30SCREWS FOR DOORS
M6*10
M6*25
95 1/2 in / 2425 mm
L21 ENDCAP
19 9/16 in / 497 mm 4mm WASHERS
CONNECTOR BRACKET
FRAME CONNECTOR
FRAME CONNECTOR
UPPER ROOF PANEL
UPPER ROOF PANEL
BACK WALL SIDE
BACK WALL SIDE
DOOR PANELS
1/4” DRILL BIT
78
PAR
TS
LIST
FO
R G
RA
-ELI
-BD
24 3/16 in / 614 mm
52 1/4 in / 1327 mm
51 3/16 in / 1300 mm
61 1/32 in / 1550 mm
37 13/16 in / 960 mm
38 11/16 in / 957 mm
FRONT & BACK
FRONT & BACK
ROOF LINE
BACK WALL
CONNECTOR
M4*30SCREWS FOR DOORS
M4.6*16SCREWS FOR ROOF VENTS
Grandio Greenhouse Limited Lifetime Warranty
1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warranted for life. The word “defects” is de�ned as imperfections that impair the use of the product.
2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installa-tion, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the greenhouse or its components are not covered under this warranty.
4. This warranty does not cover scratching or scu�ng of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use will void this warranty.
5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this product. This warranty gives you speci�c legal rights, and you may also have other rights that vary from state to state.
79
WA
RR
AN
TY
NOTES NOTES
G R E E N H O U S E S GRANDIO
®
GREENHOUSE USER MANUALKEEP IN A SAFE PLACE FOR REFERENCE
CONTACT US IF YOU NEED HELPOR
HAVE MISSING OR DAMAGED PARTS
GRANDIOGREENHOUSES.COM
BACKYARD LIVING SOURCE, INC.9543 W. EMERALD ST., SUITE 101
BOISE, ID 83704
1-866-448-8231
Grandio Elite 8x12, 8x16, 8x20 & 8x24 Models