gra eli 8x12 thru 8x24 april 15...

G R E E N H O U S E S GRANDIO

®

GREENHOUSE USER MANUAL© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved

April 15, 2016 Manual Edition Extendable Greenhouses

GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KIT MANUALINCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION

Grandio Elite 8x24 Shown In Image

STOPThis manual is for

8x12, 8x16, 8x20 & 8x24.

If building an 8x8 with no extensions refer to

that manual.


®

Before you begin, take time to complete this check list.

Take inventory of all parts using the parts list at the back of this manual on pages 68-78. The base kit parts list is at the front on page 12 and 13. The back door transformation kit parts list is on page 78.

Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and white film side faces inside green-house. Panels may scratch easily so be careful what you clean them with.

Plan out when and where you are going to place the greenhouse, we recom-mend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible

It will take at least (2) people to put the greenhouse together.

Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.

Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.

Call your local utilities companies before digging.

Do not attempt to begin construction on a windy day, plan to complete assembly in one day. Damage caused by incomplete assembly is not covered by warranty.

Your greenhouse should be built on a flat level surface allowing for drainage.

Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!

Save this owner’s manual for future reference and if you need our help.

CONTACT OUR CUSTOMER SERVICE DEPARTMENT at: 1-866-448-8231

Hours: 8:30a.m.-5:00p.m. Monday through Friday (Mountain Standard Time)

Backyard Living Source9543 W. Emerald St., Suite 101

Boise, ID 83704www.grandiogreenhouses.com

IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY

Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choos-ing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come.

Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.

Cheers!Grandio Greenhouses

1

IMPORTANT! SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instruc-tions and identify all parts using the hardware identifier and parts list on pages 68-78. Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.

CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective �lm adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners.

• Each of the polycarbonate panels have a clear �lm side that should always face the sun, and a white �lm side which faces inside. The clear side has a UV coating and we recommend marking a small “x” on a corner of each panel to determine which side has the UV Coating as you cannot visually determine with your eye in the case of future disassembly.

• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.

• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.

• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.

• If using a ladder during assembly, use extreme caution.

• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a �rm and level base. If not properly installed warranty may be void.

NEEDED FOR ASSEMBLY • Tape Measure • 2 Step Ladders • Safety Glasses• Level • Work Gloves • Drill • Carpenter Square • Permanent Marker • Folding Utility Table• At Least 2 Adults • Masking Tape • Silicone Caulk

GRANDIO

T I PWhen you see this icon

pay special attention to

the helpful tips we have provided that will

make installation more e�cient.

2


®

ASSEMBLY INSTRUCTION STEPS

PREPARE FOR ASSEMBLY

STEP ONE: BASE ASSEMBLY

STEP TWO: FRONT ASSEMBLY

STEP THREE: BACK ASSEMBLY

STEP FOUR: MIDDLE ASSEMBLY

STEP FIVE: EXTENSION ASSEMBLY

STEP SIX: DOOR ASSEMBLY

STEP SEVEN: INTERIOR ROOF SUPPORTS

3

Introduction.............................................................................1Safety Instructions.................................................................2Prepare For Assembly...........................................................4 Box Con�gurations ...............................................................5Diagrams of Assembled Grandio Elite Sizes 8x8, 8x12, 8x16, 8x20, 8x24.........................6-10 Base Kit Assembly Information.......................................11Base Kit Parts Lists........................................................12-138x12 Base Kit........................................................................148x16 Base Kit........................................................................158x20 Base Kit........................................................................168x24 Base Kit........................................................................17Base Kit Assembly and Installation........................18-20Front Wall Assembly....................................................21-26Back Wall Assembly.....................................................27-32Middle Assembly.........................................................33-38Extension Assembly...................................................39-458x20 and 8x24 Extension Assembly.....................46-50Extension Assembly Continued.............................51-60Door Assembly.............................................................61-66Interior Roof Supports.....................................................67GRA-ELI-8A Parts List.................................................68-70GRA-ELI-8P Parts List........................................................71GRA-ELI-4X Parts List.................................................72-74GRA-ELI-8XA Parts List..............................................75-76GRA-ELI-8XP Parts List....................................................77GRA-ELI-BD Parts List......................................................78Warranty..............................................................................79

PREPARE FOR GREENHOUSE ASSEMBLY

4

8X12 GRANDIO ELITE BARN STYLE GREENHOUSE DIMENSIONS

143 3/4”3652 mm

8X12

LEFT SIDE

*SEE BASE KIT ASSEMBLY SECTION FOR ALL GREENHOUSE BASE DIMENSIONS ON PAGES 14-17.


Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchor-ing options are acceptable, based on wind and ground conditions in your area.

Pre-read pages 11-20 for base kit assembly informa-tion.

Go to www.grandiogreenhouses.com for founda-tion ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together.

Transparent Clear Film

Opal White Film

Polycarbonate Panels

Sun

The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.

IMPORTANT: POLYCARBONATE PANELS

IMPORTANT: BASE KIT ASSEMBLY & GREENHOUSE PLACEMENT

97 7/16”2475 mm

44”1117.6 mm

RO

OF

PE

AK

HE

IGH

T

95 5/16”2421 mm

BASE 3 1/4”82.6 mm

1 3/4” 44.4mmGUTTERS

61”1549.4 mm

EA

VE

HE

IGH

T

DO

OR

HE

IGH

T

74”1879.6 mm

EXTENSION KIT BOX CONFIGURATIONS

GRA-ELI-8P

Elite 8’x8’

GRA-ELI-8A

+

Aluminum Extrusions, Hardware Bag, Front,

Back and Doors.

8x8 Base Kit

GRA-BAS-8


Base kit & hardware

+

Elite 8’x8’

GRA-ELI-8AAluminum Extrusions, Hardware Bag, Front,

Back and Doors.

GRA-ELI-8PPolycarbonate Panels

8x8 Base Kit

GRA-BAS-8Base kit & hardware

Elite 8’ Extension

GRA-ELI-8XA

Aluminum Extrusions, Hardware Bag, 8’ Base

Extension, 2 Roof Vents, 2 Snow Load Extension Supports.

GRANDIO ELITE 8X16

GRA-ELI-8XPPolycarbonate Panels For The 8’ Extension

+

Elite 8’x8’


Back and Doors.


8x8 Base Kit



GRA-ELI-8XA



GRANDIO ELITE 8X20



GRA-ELI-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-

ate Panels for 4’ Extension.

+ +

Elite 8’x8’


Back and Doors.


8x8 Base Kit



GRA-ELI-8XA



GRANDIO ELITE 8X24

GRA-ELI-8PPolycarbonate Panels For The 8’ Extension

+


GRA-ELI-8XA





GRA-ELI-4XAluminum Extrusions, Hardware Bag, 4’ Base Extension, 1 Roof Vent, 2 Snow Load Extension Supports, Polycarbon-

ate Panels for 4’ Extension.

Fron

t

Back

Fron

t

Back

Fron

t

Back

Fron

t

Back

5

We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site.*See the reference diagrams on pages 6-10 for more information about how the parts will go together and what makes up each section for the assembly. If building a back door you will follow the instructions in the manual, the parts for the transformation are in box GRA-ELI-BD.

GRANDIO ELITE 8X12

BACK

FRONT

620

LEFT SIDE RIGHT SIDE

6

603C

L08D

603D

601B

601B

620 604-R601A-FL 601A-FR

601B

601B

619

L08D

603C

603E

602C

602D 602D

601B

601B 601B

601B

L08B-X

601A-B

L08B

603C603C

601A-B

L08B-X

622 622

604-L

602A

602A

602A

602A

602A

602A

602B

602B

602B

602B

602B602B

609609 609

609

607

L21

610610

630 630

610610

630630

601A-B601A-B

601A-FL 601A-FR

L08A-X L08A-X

L08C-X

L08C-X

609 609610 630 609 609

610630

L08A

622-L 622-R

603C 603C

L08C-X

603C/616618

603C/616618

L08C-X

623B623B

623A 623A

606-WS606-WS Y7

Y7

Y7

Y7

Y7

Y7

Y7

Y7

Y8

Y8

Y8

Y11Y9 Y10 Y10 Y9

Y8

Y8

Y8

Y11

Y11

Y11

Y11

Y11

Y11

Y11

Y3-1 Y3-2

Y2-2Y2-1

Y6 Y6

Y6 Y6Y1 Y1

Y1 Y1Y1 Y1

Y4-1Y4-2Y5-1Y5-2

Outside View

DIAGRAM SHOWS THE ASSEMBLED(8’x8’ BASIC CONFIGURATION)

(GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8) 8x8 ELITE KIT INCLUDES, FRONT,

BACK, BASE AND SIDES.

BA-S2BA-S2

BA-S1

BA-S1

606-WS

606-WS

606-WS

606-WS

606-WS

606-WS

606-WS 606-WS

606-WS 606-WS606-WS 606-WS

7

BA-S

2

BA

CK

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

FRO

NT

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

620

LEF

T S

IDE

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ELI

-8A

and

GR

A-E

LI-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

603CL0

8D

603D

601B

601B

620

604-

R

601A

-FL

601A

-FR

601B

601B

L08D

603C

603E60

2C

602D

602D

601B

601B

601B

601B

L08B

-X

601A

-B

L08B

603C

603C

601A

-B

L08B

-X

622

622

604-

L

602A

602A

602A

602A

602A

602A

602B

602B

602B

602B

602B

602B

609

609

609

609

L21

610

610

630

630

610

610

630

630

L08M

-X

L08C

-X

609

609

610

630

609

609

610

630

622-

L62

2-R

603C

603C

L08C

-X

603C

/616

618

603C

/616

618

L08M

-X

623B

623B62

3A62

3A

606-

WS

606-

WS

Y7 Y7 Y7 Y7

Y7 Y7 Y7 Y7

Y8

Y8

Y8

Y11

Y9Y1

0Y1

0Y9

Y8 Y8

Y8

Y11Y1

1

Y11

Y11

Y11

Y11 Y1

1

Y3-1

Y3-2

Y2-2

Y2-1

Y6Y6

Y6Y6

Y1Y1

Y1Y1

Y1Y1 Y4-1

Y4-2

Y5-1

Y5-2

8x8 Elite Side

Outside View

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11Y1

1

602A

602A

602B 60

2B

Y7Y7

Y11Y1

1

Y8Y8

4X Elite Side

BA-S

2

607

607

BA-S

5

602B 602B

602B

602B

602B

602B

602B

602B60

2B

602B

609

630

609

610

609

609

610

630

(4’ Extension Side) (GRA-ELI-4X)Elite 4’ Side Extension

Includes Base

L08C

-XL0

8C-X

AZ1

AZ1

L08E

-X

L08D

-X

L08E

-XL0

8D-X

L08E

-XL0

8D-X

L08D

-XL0

8E-X

L08D

-XL0

8E-XL08E

-XL0

8D-X

L08A

BA-S

1

619

BA-S

1

(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8) 8x8 Elite Includes Front, Back, Base, and Sides

DIAGRAM SHOWS THE ASSEMBLED 8X12 GRANDIO ELITE

THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS A 4 FOOT EXTENSION KIT

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

L08A

-XL0

8A-X

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

BA-S

2

606-

WS

620

603CL0

8D

603D

601B

601B

620

604-

R60

1A-F

L60

1A-F

R

601B

601B

619

L08D

603C

603E60

2C

602D

602D

601B

601B

601B

601B

601A

-B

L08B

603C

603C

601A

-B

622

622

604-

L

602A

602A

602A

602A

602A

602A

602B

602B

602B

602B

602B

602B

609

609

609

609

L21

610

610

630

630

610

610

630

630

L08M

-X

L08C

-X

609

609

610

630

609

609

610

630

L08A

622-

L62

2-R

603C

603C

L08C

-X

603C

/616

618

603C

/616

618

L08M

-X

623B

623B62

3A62

3A

Y7 Y7 Y7 Y7

Y7 Y7 Y7 Y7

Y8

Y8

Y8

Y11

Y9Y1

0Y1

0Y9

Y8 Y8

Y8

Y11

Y11 Y1

1

Y11

Y11

Y11 Y1

1

Y3-1

Y3-2

Y2-2

Y2-1

Y6Y6

Y6Y6

Y1Y1

Y1Y1

Y1Y1 Y4-1

Y4-2

Y5-1

Y5-2

8x8 Elite Side(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BAS-8)

8x8 Elite Includes Front, Back, Base, and Sides

Outside View

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11

Y11

602A

602A

602B 60

2B

Y7Y7

Y11

Y11

Y8Y8

(8’ Extension Side) 8X Elite Side

BA-S

260

7

607

BA-S

3

BA-S

4

602B

602B

602B

602B

602B

602B

602B602B

609

630

609

610

609

609

610

630

(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP) Elite 8’ Side Extension includes Base

L08C

-XL0

8C-X

AZ1

AZ1

L08E

-X

L08D

-X

L08E

-XL0

8D-X

L08E

-XL0

8D-X

L08D

-XL0

8E-X

L08D

-XL0

8E-XL08E

-XL0

8D-X

602B

602B

602A

602B

602A

602B

Y8Y7

Y8

Y7

Y11

Y11

602B

602B

602B

602A

602A

Y11

Y11

603C

/616

618 Y1

0Y9

602B

Y7Y7

BA-S

1

BA-S

1

BA

CK

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

FRO

NT

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ELI

-8A

and

GR

A-E

LI-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.


THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT EXTENSION KIT

8

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

L08B

-XL0

8B-X

606-

WS

606-

WS

606-

WS

606-

WS

L08A

-XL0

8A-X

606-

WS

606-

WS

610

BA-S

262

0

603CL0

8D

603D

601B

601B

620

604-

R60

1A-F

L60

1A-F

R

601B

601B

619

L08D

603C

603E60

2C

602D

602D

601B

601B

601B

601B

L08B

-X60

1A-B

L08B

603C

603C

601A

-BL0

8B-X

622

622

604-

L

602A

602A

602A

602A

602A

602A

602B

602B

602B

602B

602B

602B

609

609

609

609

L21

610

610

630

630

610

610

630

630

L08A

-XL0

8A-X

L08M

-X

L08C

-X

609

609

610

630

609

609

610

630

L08A

622-

L62

2-R

603C

603C

L08C

-X

603C

/616

618

603C

/616

618

L08M

-X

623B

623B62

3A62

3A

Y7 Y7 Y7 Y7

Y7 Y7 Y7 Y7

Y8

Y8

Y8

Y11

Y9Y1

0Y1

0Y9

Y8 Y8

Y8

Y11

Y11 Y1

1

Y11

Y11

Y11 Y1

1

Y3-1

Y3-2

Y2-2

Y2-1

Y6Y6

Y6Y6

Y1Y1

Y1Y1

Y1Y1 Y4-1

Y4-2

Y5-1

Y5-2



Outside View

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11

Y11

602A

602A

602B 60

2B

Y7Y7

Y11

Y11

Y8Y8


BA-S

2

607

607

BA-S

3

BA-S

4

602B

602B

602B

602B

602B

602B

602B60

2B

609

630

609

610

609

609

610

630


L08M

-XL0

8M-X

AZ1

AZ1

L08E

-X

L08D

-X

L08E

-XL0

8D-X

L08E

-XL0

8D-X

L08D

-XL0

8E-X

L08D

-XL0

8E-XL08E

-XL0

8D-X

602B

602B

602A

602B

602A

602B

Y8Y7

Y8

Y7

Y11

Y11

602B

602B

602B

602A

602A

Y11

Y11

603C

/616

618 Y1

0Y9

602B

Y7Y7

BA-S

1

BA-S

1

BA

CK

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

FRO

NT

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ELI

-8A

and

GR

A-E

LI-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

607


THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11Y1

1

602A

602A

602B 60

2B

Y7Y7

Y11Y1

1

Y8Y8

(4’ Extensions Side) 4X Elite Side

BA-S

5

BA-S

660

2B 602B

602B

602B

609

630

609

610

609

609

610

630

(4’ Extension Side) (GRA-ELI-4X)Elite 4’ Side Extension

Includes Base

L08C

-XL0

8C-X

AZ1

AZ1

L08E

-XL0

8D-X

L08D

-XL0

8E-X

9

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

BA-S

262

0

603CL0

8D

603D

601B

601B

620

604-

R60

1A-F

L60

1A-F

R

601B

601B

619

L08D

603C

603E60

2C

602D

602D

601B

601B

601B

601B

L08B

-X60

1A-B

L08B

603C

603C

601A

-B

L08B

-X

622

622

604-

L

602A

602A

602A

602A

602A

602A

602B

602B

602B

602B

602B

602B

609

609

609

609

L21

610

610

630

630

610

610

630

630

L08A

-XL0

8A-X

L08M

-X

L08C

-X

609

609

610

630

609

609

610

630

L08A

622-

L62

2-R

603C

603C

L08C

-X

603C

/616

618

603C

/616

618

L08M

-X

623B

623B62

3A62

3A

Y7 Y7 Y7 Y7

Y7 Y7 Y7 Y7

Y8

Y8

Y8

Y11

Y9Y1

0Y1

0Y9

Y8 Y8

Y8

Y11

Y11 Y1

1

Y11

Y11

Y11 Y1

1

Y3-1

Y3-2

Y2-2

Y2-1

Y6Y6

Y6Y6

Y1Y1

Y1Y1

Y1Y1 Y4-1

Y4-2

Y5-1

Y5-2



Outside View

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11

Y11

602A

602A

602B 60

2B

Y7Y7

Y11

Y11

Y8Y8


BA-S

2

607

607

BA-S

3

BA-S

4

602B

602B

602B

602B

602B

602B

602B602B

609

630

609

610

609

609

610

630


L08M

-XL0

8M-X

AZ1

AZ1

L08E

-X

L08D

-X

L08E

-XL0

8D-X

L08E

-XL0

8D-X

L08D

-XL0

8E-X

L08D

-XL0

8E-XL08E

-XL0

8D-X

602B

602B

602A

602B

602A

602B

Y8Y7

Y8

Y7

Y11

Y11

602B

602B

602B

602A

602A

Y11

Y11

603C

/616

618 Y1

0Y9

602B

Y7Y7

BA-S

1

BA-S

1

BA

CK

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

FRO

NT

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

LEF

T S

IDE

In b

oxes

GR

A-E

LI-8

A a

nd G

RA

-ELI

-8P,

th

e b

ase

for

8x8

is a

ll in

GR

A-B

AS

-8.

RIG

HT

SID

EIn

box

es G

RA

-ELI

-8A

and

GR

A-E

LI-8

P,

the

bas

e fo

r 8x

8 is

all

in G

RA

-BA

S-8

.

602A

602A

602B

602B

603C

/616

618

Y7Y7

Y9Y1

0

Y8

Y11

Y11

602A

602A

602B 60

2B

Y7Y7

Y11

Y11

Y8Y8


BA-S

3

BA-S

4

602B

602B

609

630

609

610

609

609

610

630


L08C

-XL0

8C-X

AZ1

AZ1

L08E

-XL0

8D-X

L08D

-XL0

8E-X

602B

602B

602A

602B

602A

602B

Y8Y7

Y8

Y7

Y11

Y11

602B

602B

602B

602A

602A

Y11

Y11

603C

/616

618 Y1

0Y9

602B

Y7Y7

607


THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS (2) 8 FOOT EXTENSION KITS

10

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

606-

WS

BASE KIT ASSEMBLY INSTRUCTIONS

11

Pre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure.

Be sure the orientation will allow for proper drainage in and around your greenhouse.

It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.

The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all.

Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your greenhouse in keeping the temperature up inside.

Extreme Wind Conditions: If you live in a windy location there is no way to build a 100% storm safe greenhouse, but there are a number of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condi-tion areas where wind is constant and extreme.

See our website GrandioGreenhouses.com for Extreme Weather Anchoring Kits and Moisture Control Kits to aid in protecting your green-house in the event of harsh weather conditions prior to beginning installation.

It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants and keeping the temperature and air circulation to the max e�ciency.

You will need to choose an anchoring system prior to installation, see our website for options: www.GrandioGreenhouses.com

For Cement Base Installation: We recommend you use wedge style concrete anchoring bolts to secure your structure.

For Deck Base Installation: We recommend you use anchoring bolts to secure your structure.

For Earth Installation: We recommend you use the BA-A1 / L-BOLT anchoring system, and bury corner posts into the ground and seal into place with quickrete.

12

PAR

TS

LIST

FO

R B

ASE

KIT


BA-S5

BA-S6

BA-C4

BA-S10

BA-S03

ML01

46 3/4 in / 1187 mm

46 3/4 in / 1187 mm

8 7/16 in / 214 mm

1/2 x 3/4

M6*14

NUT

GRAPHIC PART NAME SIZE/LOCATION QUANTITY

1

1

2

2

16

16

BA-S1

BA-S2

BA-C3

BA-S03

ML01

W05

97 3/8 in / 2474 mm

94/4 in / 2394 mm

5 7/16 in 138 mm

M6*14

NUT

CLIPS

8X8 BASE KIT PARTS WILL BE FOUND IN (GRA-BAS-8) BOX


2

2

4

28

28

9

BASE KIT PARTS LIST PARTS WILL BE FOUND IN (GRA-ELI-4X) BOX

FOR THE 4’ EXTENSION BASE KIT

BASE KIT PARTS LIST

13

PAR

TS LIST

FOR

BA

SE K

IT


BA-S3

BA-S4

BA-C4

BA-S10

BA-S03

ML01

93 7/16 in / 2374 mm

93 7/16 in / 2374 mm

8 7/16 in /214 mm

1/2 X 3/4

M6*14

NUT

PARTS WILL BE FOUND IN (GRA-ELI-8XA) BOXFOR THE 8’ EXTENSION BASE KIT


1

1

2

2

16

16

BA-S1

BA-S2

BA-S1

BA-S2

BA-C3

BA-C3

BA-C3

1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.2 Attach the BA-S2 to the BA-S5 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S6 and the BA-S2. Go to page 18 for the next step.

BA-S5BA-S6

BA-C3

8x12 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-4X)

BA-C4

BA-C4

GRANDIO

T I PNote that the holes for screws on the base kit

sides have about a 2 foot gap between each, so be sure base kit extensions are assembled properly. See .

BA-C4

BA-S5 BA-S2

BA-S03ML01

14

STE

P O

NE

BA-S10

BA-S10143 3/4” / 3652 mm

97 7/16” / 2475 mm

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

BA-S2

BA-S1

BA-S2

BA-C3

BA-C3

BA-C4

BA-S3

BA-S4

BA-C3

BA-C4

1.3 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1 See diagram . 1.4 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01. See . Repeat for other side connecting the BA-S4 and the BA-S2. Go to page 18 for the next step.

8x16 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA)

BA-C3

15

STE

P O

NE

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-S10

BA-S10

GRANDIO



190 15/16” / 4849 mm

97 7/16” /

2475 mm

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S2BA-S2

BA-C3

BA-C3

BA-S3

BA-S4

BA-C3

BA-C4

BA-C3

BA-C4

BA-S5

BA-S6

1.5 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, See diagram . 1.6 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03. See . Repeat for other side connecting the BA-S4 and the BA-S2, then BA-S3 to BA-S5 and BA-S4 to BA-S6. Go to page 18 for the next step.

8x20 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA) AND (GRA-ELI-4X)

HOLE FOR ANCHOR

16

STE

P O

NE

BA-C4

BA-S5 BA-S2

BA-S03BA-M03

BA-C4BA-S10

BA-S10

BA-C4BA-S10

BA-S10

GRANDIO



237 5/8” / 6036 mm

97 7/16”

/ 2475 m

m

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

BA-S1

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

BA-S1

BA-S2

BA-S1

BA-S2

BA-C3

BA-C3

BA-S3BA-S4

BA-C3

BA-C4

BA-C3

BA-S4 BA-S3

8x24 BASE KIT ASSEMBLY INSTRUCTIONS(GRA-BAS-8) AND (GRA-ELI-8XA) AND (GRA-ELI-8XA)

1.7 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front and BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1. The BA-S3 will attach to the other BA-S3 and BA-S4 will attach to the other BA-S4 See diagram . 1.8 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and ML01.See . Repeat for other side connecting the BA-S4 and the BA-S2, and then the BA-S3 to the BA-S3, and then the BA-S4 to the BA-S4. Go to page 18 for the next step.

17

STE

P O

NE

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-C4BA-S10

BA-S10

BA-C4BA-S10

BA-S10

GRANDIO



BA-C4 284 3/8”/ 7223 mm

97 7/16”

/ 2475 m

m

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

HOLE FOR ANCHOR

18

STE

P O

NE

1.9 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 Bolt and ML01 Collard Nut combo, tighten the collard nut on the inside of the base kit using the 10mm wrench. Repeat this process on all corners. See and . Note: BA-S1 will be the front and back, while the BA-S2’ s will be the sides of your greenhouse base.

1.10 For Ground Installation only Insert the BA-S03 and the BA-A1 into the holes at the bottom side of the corners of the base, the nut will be tightened on the inside of base, see and . Locate the anchoring devices for your installation needs and follow the directions for that anchoring system. If you have not purchased an anchoring system please go to www.GrandioGreenhouses.com for anchoring kit options.

BASE KIT ASSEMBLY INSTRUCTIONS

BA-S1

BA-S2

FRONT

SIDE

BA-C3

BA-S03ML01

BA-C3

BA-S1

BA-S2

BA-S03

ML01 Collared Nut

BA-S03

ML01 Collared Nut

BA-S03

BA-C4

BA-S3 BA-S2

BA-S03ML01

BA-S10

HOLE FOR ANCHOR

HOLE FOR ANCHOR

OutdoorGround

Assembly

1.11 If using an L-Bolt / BA-A1 anchoring kit the BA-A1 must be buried in ground. See .Dig holes to bury the BA-A1’s, you determine size and depth for your location. We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package.See www.GrandioGreenhouses.com for anchoring kit options.

BASE KIT GROUND INSTALLATION

BA-S2

BA-A1

BA-S1

BA-S03 BA-A1 * Must be inserted into the ground, and secured with concrete.

GRANDIO

T I PMake sure base is squared and level before setting

anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides.

**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY

19

STE

P O

NE

20

STE

P O

NE

1.12 Holes are present in base kit for anchoring bolts see and . You determine and acquire proper fastener prior to installation for your surface. Discard the BA-S10 for deck or concrete slab installation.See www.GrandioGreenhouses.com for anchoring kit options.

Use lag boltor concrete anchors

to attach base. (Fasteners not included).

B

Deck or Patio

Assembly

Use an appropriate fastener to attach to your surface through these access holes.

BA-C4

BA-S6 BA-S2

BA-S03ML01

BA-S1

BA-C3

BA-S2

HOLE FOR ANCHORBOLT OR SCREW.

BASE KIT DECK INSTALLATION**BASE MUST BE LEVEL & SQUARE,

FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY

GRANDIO

T I PMake sure base is squared and level before setting

anchors. Use a measuring tape to ensure all corners are the same. Use level on all four sides.

If surface is uneven you may wantto purchase large washers that will fit under the base and allow fasteners to go through to use as a shim for leveling the base kit.

FRONT FRAME ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE FRONT HORIZONTAL

This picture shows the inside view of front section fully assembled.All parts for front assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.

We recommend that you assemble the front on a tarp.* If you purchased the Back Door Transformation kit you will repeat this section for your

back wall using parts found in GRA-ELI-BD , GRA-ELI-8A and GRA-ELI-8P boxes.If you want to purchase the Back Door Transformation kit call 1-866-448-8231.

GRANDIO

T I PLay �at on ground to assemble the front frame of

your greenhouse. If possible try to �nd a shady area protected from the wind. Panels can burn grass and plants if in direct light.

GRANDIO

T I PWe recommend watching our how to assembly videos

with tricks and tips for easier assembly and installation of your Grandio Greenhouse at: www.grandiogreenhouses.com

603C

L08D

603D

601B

601B

604-L601A-FR 601A-FL

601B

601B

619

L08D

603C

603E

604-R

Y3-1Y3-2

Y1 Y1

Y2-2 Y2-1

L08A-X L08A-XGRANDIO

T I PBOLT INSTALLATION TIP: Locate all nuts and bolts, pre

thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.

606-WS 606-WS

21

STE

P T

WO

Inside View

WG02 WG02

WG02WG02

22

STE

P T

WO

2.1 Prethread all S05 screws into the WG01 and WG02’s for ease of installation, see only turn S05 a few turns. Leave the mid hole open, as this is for the end cap attachment.

2.2 Use WG01 bracket to attach the (2) 601B’s together with the 603E, secure parts with the S05 screws provided see . The WG01 will slide into the groove of the 601B’s, and also slide into the groove of the 603E, screw head will remain outside chan-nel.

2.3 Install WG02’s into (2) 601B’s then tighten S05 screws when extrusions are completely tight see . Note: the fat end of the WG02 will always be on the bottom side see .

GRANDIO

T I PPRETHREAD SCREWS TIP: Locate all WG01, WG02,

and S05 screws, pre thread these to make installation easier. Note that the fat end on the WG02 will always face downward.

Inside View

601B

601B 601B

601B

603E

WG01

WG01601B601B

S05

WG02

601B

603E

WG01

FAT END

FAT END

IMPORTANT: Use only S05 Screws, other screws may damage frame.

FRONT FRAME ASSEMBLY CONTINUEDALWAYS ASSEMBLE FRONT HORIZONTAL

WG02 WG02

WG02 WG02

2.4 Insert polycarbonate panels Y3-2 and Y3-1 into place as shown in .

2.5 Attach 603E and 603D with W04 and S04/ML01 fasteners as shown in . 2.6 Attach the 603D to the 601B’s using the W04-1’s with the S04/ML01 fasteners on both sides as shown in .

Y3-1Y3-2

601B

601B 601B

601B

603E

WG01

WG02WG02

603D W04W04-1 W04-1

S04ML01W04 603E

603DW04-1 603D

601B

GRANDIO

T I PBOLT INSTALLATION TIP: Locate ML01/S04 nuts and

screws, loosely pre thread into the W04 and W04-1’s and place in the groove of the extrusion to make installation easier.

W04 W04-1

Inside View

23

STE

P T

WO

Transparent Clear Film

Opal White Film


Sun

The UV-Protected side is covered with clear �lm and must face toward the sun. The side covered in white �lm will always face the interior of the greenhouse. We suggest you peel all �lm o� completely prior to assem-bly and use a permanent marker to place a small “X” on the lower right corner of each panel on the clear side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The “X” is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp.

IMPORTANT: POLYCARBONATE PANELS


*IF USING THE MOISTURE CONTROL KIT YOU WILL USE IT NOW

2.7 View diagrams and attach the (2) 604’s and (2) 601A’s to the 619. Note the orientation of the 604’s, there are 4 di�erent 601A’s (2) for the front and (2) for the back with di�erent hole placements. The large holes should be at the top and facing forward on the front frame assembly. See diagram on this page. The 601-FR and the 601-FL will have a hole at the top side and will face forward.

shows where the corner pieces attach to 619. shows where the door frame attaches to the 619.

*If assemblling the back door you will need to drill 1/4” holes in 601A-B’s to match the front wall, these holes should face the ground during assembly.

GRANDIO

T I PMake sure the hole on the 601A-FL and 601A-FR

face to the front of greenhouse for future install of the L21 and L28 bracket that holds the door header in place.

GRANDIO



601A-FL601A-FR

604-R 604-L

619

INSIDE

OUTSIDE

INSIDE OUTSIDE

INSIDE

OUTSIDEOUTSIDE

INSIDE

Inside View

24

STE

P T

WO


TIP: If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track.

S04

ML01

604-R

619INSIDE DOOR FRAME

A

S04

601A-FR

ML01619

INSIDE Inside View

Polycarbonate panel

606-WS619

GRANDIO

T I P Transparent Clear FilmOutside Greenhouse

Opal White FilmInside Greenhouse

Polycarbonate Panel

Sun

Inside View

Y1 Y1

604-L604-R

619 606-WS

606-WS

601A-FL601A-FR

OUTSIDE

2.8 Attach 606-WS to 619, this will hold the polycarbonate panels in place. If it seems too tight slide �ngers or nut driver along edges, gently stretching the 606-WS to allow room for panels to �t .

2.9 Insert Y1 polycarbonate panels into place, make sure Y1’s slide completely into 606-WS as shown in .

2.10 Set (2) 603C’s atop the Y1 panels, then attach (2) L08D’s to the 603C’s, 601A’s and 604’s using S04/ML01 fasteners, make sure it is snug with the tops of the Y1 panels, then tighten fasteners. See .

2.11 Insert the Y2-2 and Y2-1 polycarbonate panels as shown in .

S04/ML01

603CL08D

601A604 603C

L08D

604-L 601A-FL601A-FR

L08D

603C

604-RY1 Y1

Y2-2 Y2-1

601A-FR 604-R603C

L08D

25

STE

P T

WO


2.12 Move roof and front section together and align the WG02’s into the 601A’s, and the W04-2’s into the 604’s. Insure a snug �t between the WG02’s, 601B’s and 601A’s and then tighten the S05 screws as shown in . Tighten the W04-2’s with the S04 /ML01 nut and bolt as shown in .

2.13 Attach the L08A-X to L08D and 604 to square front section loosen S04/ML01 attached to the bottom of the (2) 604’s, square the frame with carpenter square or use a measuring tape to make sure corner mea-surements are the same, also check distance across from the top of 601A’s, and also to the bottom of the 601A’s across, make sure distance is the same. Tighten L08A-X’s to hold squareness as shown in . 603C

L08D

604-R

601A-FL601A-FR

619

603C

604-L

Y1 Y1

Y2-2 Y2-1L08D

Y3-1Y3-2

601B 601B

Inside View

W04-2W04-2WG02 WG02

S05

L08A-X L08A-X

W04-2

604

603D

S04ML01

WG02

Fat EndUP

Profile View

L08A-X

601A-FLS04ML01

603D

603C L08D

WG02 601B

S05 601A-FR

S05

26

STE

P T

WO


WG02WG02

This image shows the inside view of the back wall assembly.All parts for back assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.

We recommend that you assemble the back wall on a tarp.* If you are using the Back Door Transformation Kit you will skip this section.

BACK ASSEMBLY INSTRUCTIONSALWAYS ASSEMBLE BACK HORIZONTAL

GRANDIO



Inside View

GRANDIO

T I PMake sure the UV coated side of the panel faces

outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.

GRANDIO



Polycarbonate Panel

SunWG01

L08B

603C603C

602C602D 602D

603C 603C

601A601A

L08B-X L08B-X

L08A

601B601B

601B

601B

601B

WG02 WG02

606-WS

Y1 Y1Y1 Y1

Y4-1Y5-1Y5-2

Y4-2

WG02

606-WS

27

STE

P T

HR

EE

WG02

28

STE

P T

HR

EE

3.1 Prethread all S05 screws into the WG01 and WG02, see . Leave mid hole open it is for endcap attachment.

3.2 Use the WG01 bracket to attach the (2) 601B’s together, secure parts by sliding the WG01 into the 601B’s as shown in diagram .

3.3 Install WG02’s to connect (2) 601B’s when �rmly placed between the extru-sions tighten the S05 screws, see .

Inside View601B

601B 601B

601BWG01

GRANDIO

T I PPRETHREAD SCREWS TIP: Locate all WG01, WG02,

and S05 screws, loosely pre thread these to make installation easier. Note that the fat end on the WG02 will always face down.

WG01601B601B

S05

WG02WG01

FAT END

FAT END

BACK CONTINUEDALWAYS ASSEMBLE BACK HORIZONTAL

IMPORTANT: Be careful moving or you may bend bracket.

WG02

28

STE

P T

HR

EE601B

601B

WG02

WG02 WG02

Y1Y1Y1Y1

601A-B601A-B

L08A

602C602D 602D

3.4 Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram .

Attach (2) 602D’s to L08A using S04/ML01 fasteners as shown in diagram .

Attach 602C to L08A using S04/ML01 fastener as shown in diagram .

3.5 Attach the (4) 606-WS’s to the L08A as shown in .

3.6 Insert the Y1 polycarbonate panels into the grooves of 601A, 602D and 602C. Make sure Y1 panels are inserted into 606-WS as shown in . You may need to use a screwdriver to gently open the 606-WS to �t the polycarbonate panels into the groove of 606-WS.

606-WS606-WS 606-WS606-WS

29

STE

P T

HR

EE


ML01

601A

L08A

S04 INSIDE

602D

L08AINSIDE

ML01

S04

602C

L08A

Polycarbonate Panel

606-WSL08A

Y1Y1Y1Y1

601A-B601A-B602C

602D 602D

Y4-1Y5-1Y5-2

Y4-2

3.7 Set (4) 603C’s atop each Y-1 panel, then align the pre threaded S04-ML01 fasteners in each 603C to the L08B and to each 601A-B, 602D and the 602C. When aligned tighten the middle �rst and work your way outward. See diagrams , , .

3.8 Insert the Y5-1 and Y5-2 polycarbonate panels into place. Then insert the Y4-1 and Y4-2 into place as shown in the diagram.

603CL08B

602DS04

ML01

L08B

601A-B

Inside View

L08B 603C603C603C603C

603C 603C

L08B602C

603C

602D

L08B

30

STE

P T

HR

EE


Inside View

3.9 Pre thread the S05 screws on WG01, WG02’s and the S04/ML01 on W04-2’s brackets and place into appropriate extrusion see , and . Align WG02’s into 601A’s, the W04-2’s into 602D’s, and the WG01 into the 602C. When all members are snug tighten all fasteners to lock into place.

Y1Y1Y1Y1

601A-B601A-B

602C

602D 602D

Y4-1Y5-1Y5-2

Y4-2

601B601B

601B

601B

601B

W04-2 W04-2

WG02

WG01

GRANDIO



31

STE

P T

HR

EE


601A-B

601B

WG02

WG02

WG02WG02

3.10 A. Attach (2) L08B-X’s to (2) 602D’s and L08A with S04/ML01 as shown in .

B. Attach (2) L08B-X’s to the (2) 601A-B’s with fasteners as shown in .

GRANDIO

T I PSquare by loosening bolts attached to the tops of the

L08B-X, use measuring tape to make sure corner to corner measures the same.

ML01 S04

602D

L08B-X L08A

Inside View

602C602D 602D

601A-B601A-B

L08B-X L08B-X

601A-B

S04/ML01

L08B-X

32

STE

P T

HR

EE


1

MIDDLE ASSEMBLY INSTRUCTIONS

4.1 We recommend pre threading all (9) W05 clips with the nut and bolt combos now. See , note the bolt head will always slide into the extru-sion, W05 clips will be used in step 4.5.

4.2 With no less than 2 people place the pre assembled front section on top of the base kit front. Have person (1) hold the front vertically while the other attaches the front section 601A’s to the base using S04/ML01 fasteners as shown in .Person (1) must continue to hold up the front wall!

GRANDIO

T I PYou will need a minimum of (2) people to complete the

middle assembly of your greenhouse. The more people the merrier at this stage of assembly.

Warning: The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.

33

STE

P F

OU

R

BA-S1

BA-S2

BA-S1

601A

601A604

BA-S5

BA-S6

BA-S2

601A

ML01S04

Inside ViewFront Right side

BA-S1F

2

**This Base shows a 8x12, your greenhouse may be longer and configured of more base kit pieces.

If building a greenhouse with a front and back door you will repeat steps 4.1-4.5 for attaching both front and back walls of the greenhouse. ML01/

NUT

S04 BOLTW05CLIP

34

STE

P F

OU

R

MIDDLE ASSEMBLY CONTINUED

601A

601B

L08A-X

L08C-X L08D

L08C-X

Base

4.3 Attach L08C-X to 601A and the BA-S2 with S04/ML01 on both sides as shown in and with the nut and bolt combos.4.4 Attach the front section 619 to the base using (3) S10/ML02 fasteners as shown in , then attach the threshold support 619-BAR to the inside of the 619 with (5) S19 self tapping screws included in the package, see .

2

1

BA-S1

604

601A

601A

619 Attaches to the base kit with S10/ML02

619-BAR will attach with the (5) S19screws

1

4.5 Have person (1) continue to hold the front vertically while the other attaches the font section to the base with W05/S04/ML01 fasteners as shown in , and . The (4) W05 clips will catch the under edge of the front base kit and then slide upward attaching to the bottom of the 601A’s and the 604’s. To do this you will slide the bolt into the extrusion, slide it down to catch the edge of the base kit, then slide up and hold up as high as it will go and then tighten the ML01 nut, note you will have to switch out the combo that was originally used to the W05 Clip. If you are having a tough time using the ML01 �anged nuts in the corners, you may switch out to the ML02 nuts without the �anged edge instead.

If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall.


BA-S1

604

601A

601A

2

BA-S2

BA-S1BA-S5

BA-S6

35

STE

P F

OU

R

BaseBA-S1

W05619

Inside

BA-S2

601AML01S04

Inside View

W05

BA-S1

ML01 S04

L08A-X 619

604-R

W05


4.6 Attach back wall 601A’s with back base corners using S04/ML01 on both sides as shown in .

4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in . Attach the L08C-X to the 601A as shown in , make sure the S04/ML01 combos are tight.

4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A’s meet the corner of the base as shown in , and where 602D’s, and the 602C meet the BA-S1B see . Then use W05 Clip combos to attach the corner 601A’s to the base kit as shown in , you will have to switch out the combo that was originally used to the W05 Clip.

601A

601B

L08B-X

L08C-X L08B

W05

Base

602C, 602D

Outside

Inside

L08C-X

L08C-X

602D 602D

602C

36

STE

P F

OU

R

BA-S2 orBA-S6

601A

ML01S04

Inside ViewBack Left side

L08C-X

Base

Back Wall BA-S1601AML01S04

BA-S2 orBA-S6

Inside View

W05

Back Base

Back Base

If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then skip ahead to step 4.9.

BA-S1

L08C-X

Repeat these steps if you are building an 8x20 or 8x24 with your last extension box, note it is best to connect 8x8, then 8X, then a 4X if assembling an 8x20. Note that the notches shown in should be spaced every 2 feet, none should be right next to each other.

4.9 Attach the 607 to 607 extension with the 607-XS and the (4) S08 screws provided see , . The S08 screws are to be installed on the inside as shown in diagram . Wait to tighten the screws all at one time when both sections are aligned correctly, apply even pressure while tightening.

4.10 Apply a bead of silicone to the seam where the 607’s meet and to the holes where the S06 screws will attach the DP01 to the 607 ridge. See . Immediately align the DP01 apply a small amount of silicone to the holes on the exterior of DP01 then insert the S06 screws.

607

607607-XS

APPLY SILICONE CAULKTO RIDGE AND HOLES

S06

For 8x20 and 8x24 Grandio Elite Assembly


37

STE

P F

OU

R

607-XS

607

607

DP01

FRONT

DP01607

607

FRONT

S06

S08

WARNING

Notches

Notches


607

607

601B 601B

Inside View

Side Angle View

607

601B 601B

Inside View

S04/ML01

4.11 With 2 people, attach the ridge to front and back by sliding into place as shown in and , using S04/ML01 fasteners attach the 607 to the 601B’s. See for how the �nal orientation should be.

607

38

STE

P F

OU

R

601B

601B

EXTENSION ASSEMBLY INSTRUCTIONS

Warning: You will need a minimum of 2 people to complete this section, you will not be able to stop assembly until page 45. Note that if you are assembling an 8x20 or an 8x24 greenhouse you will proceed thru the 2nd extension assembly instruc-tions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier.

GRANDIO

T I PBOLT INSTALLATION TIP: Locate about 30 nuts and

bolts and pre thread for easiest installation.

Warning: This section will take about 30 minutes so be prepared to �nish as there is not a stopping point until page 45 for an 8x12 or 8x16 Greenhouse, or for an 8x20 or 8x24 Greenhouse page 50. Note it may be helpful to have a few more people at this point the more the merrier.

39

STE

P F

IVE

L08M-X

L08M-X

W14 BRACKET5.1 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.

5.2 Attach the 602A to the base with a nut and bolt combo where the extension kits meet on the base kit, with other person holding the 602A in place. Measure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .

5.3 Attach (2) L08D-X’s to the 602A and to the base using the ML01/S04 Combos. See and .

BA-S2BA-S2

L08D-X

Measure 6”

Measure 6”

BASE

L08D-X

602A

6”

W14

602A

L08M-X W14

602A

L08D-XL08M-X

602AL08D-X

607


40

STE

P F

IVE

Back

IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN

Back

Front

5.4 Attach the 609-XS to 609 with the (2) S09 screws provided see . The S09 screws are to be installed from the outside of the 609, see .

Pay special attention to the orientation of the 609, make sure the correct side faces down, see .

609

Profile View

Groove 609

609-XS

S09

609-XS

FRONT


41

STE

P F

IVE

FRONT

UP

UP

UP

OUTSIDE VIEW

INSIDE VIEW

5.5 With 2 people proceed to install 609 in this order, note that 609 must be installed with groove side down see .

1. With one person holding the 609 level and in position have the other person loosen the top of the L08C-X and let it fall free, attach the 609 to the 601B using S04/ML01 (nut and bolt). See and .

2. Now move the loosened S04/ML01 (nut and bolt) currently attached to the L08C-X upward to secure the 609, 601A-F and L08C-X together as shown in .

3. Have assistant keep holding at the middle section . Turn to next page for detailed installation.

L08D L08C-X601A

LOOSENML01

Inside View

GRANDIO

T I PYou will need a minimum of (2) people to complete the

middle assembly of your greenhouse. The more people the merrier at this stage of assembly.

1

2


42

STE

P F

IVE

L08B

L08D

L08C-X601A

601A

601A

601AL08C-X

L08C-X

L08C-X

L08D

601B

601B

601B

UP

601B

609

Profile View

Groove

601A

Note the line on the 609 that shows the exact placement of the 601B’s and the 601A’s when installedcorrectly.

601B

609

S04/ML01

L08C-XL08D

Inside View

601A

43

STE

P F

IVE

609609

602A

NOTE EXACT PLACEMENT OF THE 602A TO THE 609.

EXACTPLACEMENT LINE FOR 602A

4. Note the top of 602A should touch the line on the 609 for exact placement, see . Attach the 609 to the 602A with the S04/ML01 nut and bolt combos see diagram .

5. Repeat steps 1-4 on the other side see .

602A

609609-XS

S04/ML01

602A

FRONT

FRONT


602A

OUTSIDE VIEW

INSIDE VIEW

44

STE

P F

IVE

5.6 Moving up to the midroof 609, with person 1 holding the 609 in place person 2 will attach the 609 to the front of the greenhouse to the 601B’s, see . Person 1 will continue holding the 609.5.7 Person 2 will attach the 602B to the 609’s see . Attach one more 602B between the 609 and 607, see .Repeat on the other side of greenhouse.

1

2

609

609

602B

607 Roof Line

609

Outside View

Inside View

602B

609

607

EXACT PLACEMENT

602A

FRONT


Inside View

609

ML01/S04

601B

601B

609

602B

602B

ML01/S04

609-XS

FRONT

FRONT

607 Roof Line

** 8x16 Elite Shown

45

STE

P F

IVE

609

609

602B607

609

602A

BZ-1

AZ-1

1

2

5.8 With two people attach the AZ-1 to W17 and the base and the lower 602A, see . Next attach the upper end to the mid roof line touching the 609 see for exact placement. Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo. 5.9 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s. Note the exact placement of the edge of the BZ-1 should touch the top edge of the 609 see .

601B

601B

AZ-1

S04ML01

BZ-1

S02ML01

609

609-XSIF YOUR GREENHOUSE IS AN 8X12 OR 8X16 SKIP TO PAGE 51. IF YOURS IS AN 8X20 OR 8X24 PROCEED ON TO THE NEXT PAGE.


AFTER COMPLETING STEP 5.9

** 8x16 Elite Shown

UP Front

602A

AZ-1

S02/ML01

INSIDE VIEW

W17 BRACKET

S02/ML01You will need to switch this bolt out to an S02

FRONT

AZ-1

ML01W17 BracketNote orientationof bracket

S02

(7mm gap edge will fitdown into base bottom)

10mm7mm

1

5.10 Connect the (2) braces labeled L08M-X together with the nut and bolt combo S04/ML01 see . The combined L08M-X’s should measure about 94 1/2” when connected together.

5.11 Attach the 602A to the base with a nut and bolt comboMeasure down 6” from the top of the 602A to attach the W14 bracket to the 602A on both sides with the S04/ML01 . See and . Attach the assembled L08M-X’s to the W14 as shown in and .

5.12 Attach (2) of the L08D-X supports to the 602A and to the base using the ML01/S04 Combos. See and .

BA-S2L08D-X

BASE

L08D-X

602A

6”

W14

Measure 6”

L08M-X

602A

L08D-X

Measure 6”602A

L08D-X

L08M-XL08M-X

W14 BRACKET

602AL08M-X W14

46

STE

P F

IVE

2nd EXTENSION ASSEMBLY INSTRUCTIONSCONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19

Back

IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN

Back

Front

5.13 Attach the 609-XS to 609 with the (2) S09 screws provided see . The S09 screws are to be installed from the outside of the 609, see .

Pay special attention to the orientation of the 609, make sure the correct side faces down, see .

609

Profile View

Groove

47

STE

P F

IVE

2nd EXTENSION ASSEMBLY INSTRUCTIONS

OUTSIDE VIEW

INSIDE VIEW

CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19

609

609-XS

S09

609-XS

FRONT

FRONT

UP

UP

UP

1

1

609-XS

609609-XS

609-XS

2

609-8X-L609

S09609-XS

GAP FOR SCREWS

609-XS

5.14 With 2 people proceed to install 609 extension at the eave or lower mid roof in this order.

1. With one person holding the 609 level and in position have the other person attach the 609 to other end of the 609-XS as shown in .

2. With one person holding the 609 level and in position have the other person attach the 609 to the 602A using S04/ML01. See .

3. Repeat steps 1. and 2. on other side of the greenhouse.

609609-XS

609-8X-L

609-XS

609

602A

NOTE EXACT PLACEMENT OF THE 602A TO THE 609.

EXACTPLACEMENT LINE FOR 602A

FRONT

FRONT

48

STE

P F

IVE

2nd EXTENSION ASSEMBLY INSTRUCTIONS

2

1

CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19

UP

609-8X-R

1

609-8X-L

1

2

5.15 With person 1 holding the 609 in place person 2 will attach the 609 to the 609-XS with the (2) S09’s screws to the upper mid roof see . Person 1 will continue holding the 609.5.16 Person 2 will attach the 602B to the two 609’s with (2) S04/ML01 (nuts and bolts) see . Attach one more 602B between the 609 and 607 with (2) S04/ML01 (nuts and bolts), see .Repeat both steps on the other side of greenhouse.

Outside View

602B

609

607

EXACT PLACEMENT

2

609-8X-L609

S09609-XS

GAP FOR SCREWS

FRONT

49

STE

P F

IVE

602B


FRONT

Inside View

609

602B

602B

ML01/S04

609-XS

FRONT 607 Roof Line

609-8X-R

2

5.17 With two people attach the AZ-1 to W17 with the base and the lower 602A, see . Then attach the upper end to the mid roof line touching the 609 see for exact placement. Install on both sides of the greenhouse where the extension seams meet using the S02/ML01 combo.

5.18 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the (2) 602B’s. Note the exact placement of the edge of the BZ-1 should touch the top edge of the 609 see .

601B

601B

AZ-1

S04ML01BZ-1

S02ML01

609

609-XS

BZ-1

AZ-1

1

609609

602B

50

STE

P F

IVE


FRONT

602A

AZ-1

S02/ML01

INSIDE VIEW

W17 BRACKET

S02/ML01You will need to switch this bolt out to an S02

FRONT

AZ-1

ML01W17 BracketNote orientationof bracket

S02

(7mm gap edge will fitdown into base bottom)

10mm7mm

2

2

609

607

609

1

602A

609 609-XS

ML01/S04

609-8X-L

5.19 With two people attach the 609 extension to 609-XS with the (2) S09 screws provided see and .

5.20 With person 2 still holding in place have person 1 loosen the L08C-X nut and bolt combo, allow to fall out of place, then align the 609 into place with the 601B and 601A, see . Use a S04/ML01 combo to attach the 609 to the 601B, then slide the nut and bolt combo attached to the L08C-X into place to secure the 609 between the 601A and the L08C-X.

Repeat these steps on other side of the greenhouse, and then mid roof line see .

609-8X-L609

S09 609-XS

609

601BML01/S04

FRONT

FRONT

MIDDLE BACK ASSEMBLY INSTRUCTIONS

51

STE

P F

IVE

601B

601B

601A-B

609-8X-L

OUTSIDE VIEW

INSIDE VIEW

INSIDE VIEW601B

609

S04/ML01

L08C-XL08B

Inside View

601A

* Note Notch Placement: Notches will have about a 23” space between notches, notches will not be right next to each other when attaching the extension 609.

5.21 Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the ML01 (nut) attached to the L08C-X and the base. See diagram . Remove and set aside the L08D-X supports.

1. Once the bottom of one L08C-X is loosened set the 602A onto the bolt of the L08C-X. Be sure the 602A is aligned and sitting �ush on top of the base kit. See for reference.

2. Hold the 602A in place and attach the top of the 602A to the 609 using S04/ML01 (nut and bolt). As shown in .

3. Repeat steps 1. and 2. on all four corners where the L08C-X ‘s meet the base kit.

4. Now attach the bottom of 602A to the Base using a S04/ML01 (nut and bolt) as shown in , and to the 609 with an S04/ML01 combo as is shown in .

5. Repeat step 4. on all places where a 602A should go. You may reference diagrams at front for your exact size.

Note: Where the L08C-X reattaches to the BASE and the 602A be sure to secure them tightly see .

L08C-X

602A

L08C-XS04ML01BASE

Inside View

609

602A

Inside View

BA-S2

602A

Inside View

ML01/S04ML01/S04

L08C-X

52

STE

P F

IVE

MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED

L08D-X

L08D-X

602A

602A602A 602A

602A

Loosen only one L08C-X at a time.

Slide L08C-X

into place

5.22 Install only the upper roof line 602B’s between the 607 and the 609 along the entire upper roof line with S04/ML01 (nut and bolt). See and . Repeat on other side of roof section.

Do Not attach lower roof 602B’s yet, they will get in your way when installing the upper roof panels and roof vents.

ML01S04

609

602B

Outside View

602B

609

607

EXACT PLACEMENT

609

607

53

STE

P F

IVE


TOP

TOP

GRANDIO



Polycarbonate Panel

Sun

602B

Roof Line

5.23 Insert Y11 panels to upper roof section then slide the 630 into the groove of the upper 609 as shown to hold Y11’s in place. See and . Note that you may need to loosen the bottoms of some of the 602B’s to slide the 630’s into place as the �t is very tight. Check that all nut and bolt combos are tightened again after installation of 630’s. Note that there is a 630 in the extension box(s), make sure you install so the screw holes on the 630’s align for the DP03 to attach. Once the 630’s are aligned apply a streak of silicone to the seam of the 630’s, then align the DP03 with the holes and a�x into place with the S06 screws provided. See .

Y11

Y11Y11

Y11Y11 Y11

630

609

630601B

601B609

630601B

601B609

630

609

Left Profile View Right Profile View

607

609

602B


54

STE

P F

IVE

602B602B

602B602B

APPLY SILICONE CAULKTO RIDGE AND HOLES

DP03

S06630-4X-R

Right Side of GreenhouseIs Shown in Image

FRONT BACK

601B

601B

601B

601B

630

630-4X-L

The two profiles should be flush at ends when installed correctly.


SUN

616 615PC sheet

5.24 Assemble the roof window vents as shown below in and , using the Z02 screws attach the 615, 616, and 618’s with the Y10 panel as shown, be careful not to strip the screw heads. Pay attention to the Y10 panel, as the stickers must face the sun.

5.25 Insert assembled window into the end of the ridge of 630 and slide into position. See . Window positions are your discretion however, may not be placed nearest the front or back as you will need a 602B support to keep in window vent in place, and may not be right next to another vent. Place directly across from each other for best cross draft ventilation, see for optional placement.

**It is recommended to apply silicone caulk to the exterior seams on the bottom and sides of each panel, where panels meet the frame for water resistance, or see the Moisture Control Kit on our website to maintain panel clarity. The interior and top of each panel is protected so it is recommended that you leave them un-caulked allowing the panels to breathe.

GRANDIO

T I PPlace roof windows in desired location before

attaching all 602B’s. Note the 8x12 has 3 windows, an 8x16 has 4 windows, an 8x20 has 5 windows and an 8x24 has 6 windows.

Y10

Y10

Y10

SUN

Y10

618

Z02

Z02

Z02

Z02

Z02618

ScrewdriverOutside View

Roof VentPlacement

Inside of window

615

616

618616

Z02

Note Correct Orientation

630

55

STE

P F

IVE

MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED630

Inside

Roof Vent

602B

602B

Y10

Y10

Polycarbonate Panel

606BASE

Outside

5.26 Attach all remaining 602B’s between the 609’s, after all roof vents are positioned see .

5.27 Install plastic strip 606-WS before inserting polycarbonate sheet Y7’s, see .

5.28 After Y7’s are installed on both sides, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust 602A and tighten bolts. Repeat in every corner until the greenhouse is plumb. The top edges of Y7’s will align when greenhouse is level or plumb.

Y11Y11

Y11

Y11

Y11

Y11

606-WS

Outside View

602B

609

607

EXACT PLACEMENT

602A

602A

56

STE

P F

IVE


5.29 To ensure there is no gap in roof vent position 603C as shown in . Connect 603C to middle of 602B’s using W04 bracket as shown in .

5.30 Attach HQC01 to 616 with the Z04 screws see , close roof vent and attach the handle onto HQC02 middle pin (the �rst two holes of the handle to the second and third pins of HQC02). Then attach HQC02 into 603C’s track with S04/ML01 (nuts and bolts), see .

603C

618

616

616

603C

616

Z04

HQC02

Y10

Y10

HQC01Handle

Y10603C

Inside view of 603C603C

602BW04

Note: If you are installing automatic roof vent openers follow those directions for correct installation.SAVE MANUAL HARDWARE FOR WINTER SWITCHOUT.

HQC01Handle

57

STE

P F

IVE


HQC01Handle

603C

HQC02

HQC01Handle

ML01/S04

Inside View

1 2 3

Y10

Y10

Y11Y11

Y11

Y11

Y11

5.31 Remove the L08M-X support combo, take apart and install on the sides of the AZ1 extension brace, as shown in . Save the hardware and W14 bracket for possible future use or hang inside as a plant hanger clip.

5.32 Insert polycarbonate sheets Y8’s and Y9’s into the lower roof of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown in the diagram once the panels are in place.

5.33 Slide 610 Gutters into 609’s groove as shown in diagram . Repeat on both sides. Note the orientation of the gutters, the extension gutters will be at the back and the holes should align with gutter down spout hole see next page.

Y11

L08M-X

L08C-X

L08C-X

L08M-X

601B

601A

610

609

609

610

Gutter

Outside View

Y8Y9

Y8

Y8

Y9

58

STE

P F

IVE


AZ1


TAPE

59

STE

P F

IVE

DP02B

DP02

610-8X-L

610

5.34 Apply a small amount of the silicone caulk to the seam where the 610 gutters meet, then attach the DP02 on the inside of the gutter and the DP02B will slide under the gutter and will rest above the 602A. Apply silicone to the holes where the S07 screws will attach the 610 gutters to the DP02 and DP02B. Note the DP02B has pre-tapped holes to accept the screws and hold tight. See diagram and .

Repeat these steps to assemble the additional set(s) for both sides of your greenhouse.Remove the tape from the panels you may have used to hold in place.


DP01

610

610

602A

602B

60

STE

P F

IVE

JG03A Z03

JG02A

JG01

JG03B

Z03

JG02B

4.25 Attach JG01, JG02A, JG02B, JG03A and JG03B end caps to the ridge, midroof and gutters on both front and back as shown below. Use Z03 screws to attach the JG03A and JG03B endcaps along with the silicone adhesive. Use Z06 screws to fasten end caps through the WG01 and WG02 as shown in images. Note you may want to seal into place with silicone caulk on the inner side and around the edges.


Exterior view of mid roof cap JG01.

Z06

Interior greenhouse view of mid roof cap, where Z06 screw goes through WG01 mid hole into the end cap.

DOOR ASSEMBLY DIAGRAM

Z01622

Y6

Y6

622-R

UP

UP

Catch

620Z01

Z01

Z01

Z01

Z01

623B

623A622Side View

622

J08A

BottomView

623B

620

623A

J08A

J08A

622-R

UP

UP

Side View

622

J08A

BottomView

Inside View

This image shows the inside view of Right Door Assembly.All parts for door assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.

Use the #2 head Phillips Screw Driver for installation.If you are using the Back Door Transformation kit you will repeat steps 6.1-6.11 to install the Back Door,

these parts will be found in box GRA-ELI-BD.

61

STE

P S

IX

623B

623A

622

J08A

BottomView

J08A

We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orienta-tion of what is inside verses outside and how the doors will hang on page 63-67. Make sure window panels face the right direction to the sun and note that the panels may have predrilled holes for the handles to attach later and these need to be aligned with the lock mechanisms, if you do not see any holes you will need to drill the holes out before installing the door handles. Be careful not to strip the phillips heads when assembling. 6.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .6.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .6.3 Insert Y6 windows into position as shown in .

623B

Z01

620Z01

Z01623B

623A

622 620

623A

622

620

Y6

Y6

GRANDIO



Polycarbonate Panel

Sun

622

UP

UP

Side View

Inside View

62

STE

P S

IX

DOOR ASSEMBLY

You may need to gently open the channel with a flat head screwdriver if screws are not going into place with ease.

FLUSHALIGNWITH TOP

J08A

622

J08A

BottomView

Side ViewOf Top

* DoubleBall Catch

on the 622-L

622-L

UP

UP

Side ViewOf Bottom

6.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see .6.5 Attach the 622-L to the 623B, 623A and 620 using the Z01 screws as shown in .6.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball and catch match up so doors will latch closed and slide properly .

Y6

Y6

623B

623A

620

622-R

Catch

Z01

Z01

Z01

622-R

Side ViewOf Top

* Catch on the 622-R

622-R

UP

UP

Side ViewOf Bottom

* Note the orientation of the 622-L and 622-R. Also make sure the right side is facing out on the Y6 polycarbonate panels.

Inside View622

DOOR ASSEMBLY CONTINUED

63

STE

P S

IX

DOOR INSTALLATION

64

STE

P S

IX

S02

L21

603D

6.7 Slide the (2) S02 bolts down the track of the L21 see , align with the holes on the 603D door header. With one person inside the greenhouse line up hanging door track L21 with door header 603D, move bolts on L21 to line up with bolt holes on door header 603D. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will now center on the front of the greenhouse and tighten the S02/ML01 combo.

1

2

Side Profile View of L21 Hanging Track

Inside View

Track

S02SCREW

S04 S04S02

6.8 Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle.

6.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and .**We included some felt dots in your Grandio Welcome Kit, please apply to the inside bottom edge of the 623B as shown in , these felt dots will make your doors �t snug and slide smoothly.

DOOR INSTALLATION

Outside View Inside View

Top

Bottom

Side Profile View of Hanging Track

L21 L21

622-HNDL

622-HNDLNUT/BOLT

622-HNDL

622-HNDLNUT/BOLT

65

STE

P S

IX

623B623B

6.10 Attach L28 to L21 with S04/ML01, and L28 to 601A with WASHER and S02/ML01 as shown below in diagram and . Check that the L21 and L28’s are square. Attach (2) J07 to the ends of L21 see . The L28 should align square to the 601A.

6.11 Check that the door locks are snug, you may adjust them with screwdriver if needed as they can be tightened or loosened.

DOOR INSTALLATION

601A

S02

L28

601A-FR

601A-FL

66

STE

P S

IX

Top Profile View

J07L21

L28

S02

601A

ML01 WASHER

Backside View

603D

L21

L28

S04/ML01

Top LeftProfile View

INTERIOR ROOF SUPPORT ASSEMBLY 7.1 Attach the L08E-X to the upper roof section as shown with S04/ML01 fasteners already in place where the 607 meets the 601B, and the 609 and the 602B meet see , repeat this on the front section of the greenhouse, and where extensions meet at the AZ-1.

7.2 Attach the L08D-X to the rear lower roof section where S04/ML01 fasteners are already in place where the 609 and the 602B meet, and the 609 and the 601B meet see , repeat on the front section, and where the extensions meet the AZ-1. 7.3 Attach the BZ-1’s to the roof line as shown in diagram with the S04/ML01. The edge of the BZ-1 should meet up to the edge of 609 exactly.

7.4 Use CZ-1’s to support the interior wall at the eave using the S04/ML01. See diagram . We suggest that you measure down 9” and mark it with a pencil so the base of the CZ-1 will meet there.

You may remove all stickers now with Goo Gone remover if needed.

L08E-X

L08D-XL08D-XCZ-1 CZ-1

BZ-1

9” 9”

L08D-X

L08E-X

BZ-1

CZ-1602B

607

609Roof Vent

602B

601B

601B

609

609

607

67

STE

P S

EV

EN

601B 601B

Congratulations You Did It!!

68

PAR

TS

LIST

FO

R G

RA

-ELI

-8A

601A-B

601A-FL

601A-FR

601B

602A

602B

602C

602D-R

602D-L

603C

603D

603E

619 PACK619-BAR

S19 SCREWS10 / ML02

604-R

604-L

607

606-WS

609

610

615

616

618

630

L08A

NOTE THESE ARE PACKED TOGETHER

L08B

56 9/16 in / 1437 mm BACK CORNERS

56 9/16 in / 1437 mm FRONT LEFT CORNER

56 9/16 in / 1437 mm FRONT RIGHT CORNER

29 7/16 in / 748 mm CORNER ROOF

56 9/16 in / 1437 mm

29 7/16 in / 748 mm

90 1/2 in / 2299 mm

83 1/4 in / 2115 mm

83 1/4 in / 2115 mm

21 7/8 in / 555 mm

72 3/16 in/ 1833 mm

18 1/4 in / 463 mm

94 1/4 in / 2394 mm44 1/2 / 1130

M4*10M6*16 / ML02

70 3/4 in / 1797 mm FRONT RIGHT

70 3/4 in / 1797 mm FRONT LEFT

94 1/4 in / 2394 mm

21 3/4 in / 553 mm

94 1/4 in / 2394 mm

94 3/8 in / 2397 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 11/16 in / 500 mm

94 3/8 in / 2397 mm

94 1/4 in / 2394 mm

94 1/4 in / 2394 mm

(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST

GRAPHIC PART NAME SIZE/LOCATION QUANTITY GRAPHIC PART NAME SIZE/LOCATION QUANTITY

2

1

1

8

6

12

1

1

1

8

1

1

1 - 6191 - 619 Bar

5 - S19 Screws3 - S10 / ML02

1

1

1

14

4

2

2

2

4

2

1

1

69

PAR

TS

LIST

FO

R G

RA

-ELI

-8A

L08D

L08A-X

L08B-X

L08C-X

L08D-X

L08E-X

WG01

WG02

W04

W04-1

W04-2

Z01

Z02

24 3/16 in / 614 mm

52 1/4 in / 1327 mm

51 3/16 in / 1300 mm

61 1/32 in / 1550 mm

37 13/16 in / 960 mm

38 11/16 in / 957 mm

FRONT & BACK

FRONT & BACK

ROOF LINE

BACK WALL

CONNECTOR

M4*30SCREWS FOR DOORS

M4.6*16SCREWS FOR ROOF VENTS

AZ-1 / W17S02/ML01

S02/ML01

S04/ML01

S05

Z04, S04/ML01

HQC01

HQC02

L28 / WASHER

W11

W13

W16

BZ-1

CZ-1

86 1/4 in / 2190 mmEXTENSION SUPPORT

M6*25

M6*14

M6*10SCREWS FOR WG01 AND WG02

ROOF VENT HARDWARE

ROOF VENT ARM

ROOF VENT LATCH

19 9/16 in / 497 mm 4mm WASHERS

MULTI-DRIVER

10 MM NUT DRIVER

10 MM WRENCH

56 1/2 in / 1435 mm

23 5/8 in / 600 mm

2

2

2

4

4

4

2

8

5

2

4

13

9

2

6

150

45

4

2

2

2/2

1

1

1

3

6

GRAPHIC PART NAME SIZE/LOCATION QUANTITYGRAPHIC PART NAME SIZE/LOCATION QUANTITY

(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST

70

PAR

TS

LIST

FO

R G

RA

-ELI

-8A

622-HNDL

622-HNDLNUT/BOLT

620

L21

J07

622

622-R

622-L

623A

623B

J08A


4

4

2

1

2

2

1

1

2

2

4

DOOR HANDLES

DOOR HARDWARE

21 7/16 in / 545 mm

95 1/2 in / 2425 mm

L21 END CAP

69 11/16 in / 1770 mm

69 11/16 in / 1770 mm

69 11/16 in / 1770 mm

21 7/16 in / 545 mm

21 7/16 in / 545 mm

DOORS

(GRA-ELI-8A) 8’x8’ GRANDIO ELITE ALUMINUM PACKING LIST

JG01

JG02 A/B

JG03 A/B

Z03

Z06

ML02


2

2/2

2/2

4

10

8

RIDGE END CAP

MID ROOF END CAP

GUTTER END CAP

M3*25

M4*10

NON FLANGED NUTS

71

PAR

TS

LIST

FO

R G

RA

-ELI

-8P

(GRA-ELI-8P) 8’x8’ ELITE PANEL BOX PACKING LIST

Y1

Y2-1

Y2-2

Y3-1

Y3-2

Y4-1

Y4-2

Y5-1

Y5-2

Y6

Y7

Y8

Y9

Y10

Y11

FRONT & BACK PANEL

FRONT PANEL

FRONT PANEL

FRONT PANEL

FRONT PANEL

BACK PANEL

BACK PANEL

BACK PANEL

BACK PANEL

DOOR PANEL

SIDE WALL PANEL

ROOF PANEL

UNDER ROOF VENT

ROOF VENT PANEL

ROOF PANEL

GRAPHIC NAME SIZE/LOCATION WIDTH HEIGHT 1 HEIGHT 2 QTY

6

1

1

1

1

1

1

1

1

4

8

6

2

2

8

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

35 1/2 in / 902 mm

35 1/2 in / 902 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

47 5/16 in / 1202 mm

9 1/16 in / 230 mm

23 in / 585 mm

9 15/16 in / 252 mm

19 1/8 in / 486 mm

9 1/16 in / 230 mm

35 3/16 in / 894 mm

35 7/16 in / 900 mm

42 13/16 in / 1087 mm

34 in / 864 mm

57 in / 1447 mm

30 5/8 in / 778 mm

8 7/8 in / 225 mm

19 1/8 in / 486 mm

30 3/8 in / 772 mm

23 in / 585 mm

9 1/16 in / 230 mm

19 1/8 in / 486 mm

9 15/16 in / 252 mm

35 3/16 in / 894 mm

9 1/16 in / 230 mm

42 13/16 in / 1087 mm

35 7/16 in / 900 mm

602A

602B

603C

L08M-X

L08D-X

L08E-X

607-4X

607-XS

DP01

609-4X-R609-4X-L

609-XS

DP03

606-WS

610-4X-R610-4X-L

DP02

DP02B

630-4X-R630-4X-L

615

616

618

BZ-1

CZ-1

Z02

S04 / ML01

S06

56 9/16 in / 1437 mm

29 7/16 in / 748 mm

21 7/8 in / 555 m

61 in / 1550 mm

37 13/16 in / 960 mm

37 11/16 in / 957 mm

46 3/4 in / 1187 mm

ROOF CONNECTOR

ROOF CONNECTOR

46 3/4 in / 1187 mm

EAVE CONNECTOR

630 CONNECTOR

21 3/4 in / 553 mm

46 3/4 in / 1187 mm

GUTTER BRACKET

GUTTER BRACKET

46 3/4 in / 1187 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 11/16 in / 500 mm

56 1/2 in / 1435 mmROOF SUPPORT

23 5/8 in / 600 mmEAVE SUPPORT

5X12 MMSCREWS FOR ROOF VENT

M6*14

4*10ATTACHES DP01 TO 607


4

8

1

2

2

2

1

1

1

4

4

2

4

2

2

2

2

1

1

2

2

2

5

50

3

72

PAR

TS

LIST

FO

R G

RA

-ELI

-4X

(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST

S07

S08

S09

W04

W14

HQC01

HQC02

Z04, S04/ML01

M5*8SCREW FOR DP02 AND DP02B

M6*16ATTACHES 607-XS TO 607


CONNECTOR FOR 603C

L08M-X BRACKET

ROOF VENT ARM

ROOF VENT LATCH

ROOF VENT HARDWARE


5

5

20

2

2

1

1

4 EACH

73

PAR

TS

LIST

FO

R G

RA

-ELI

-4X

(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST

74

PAR

TS

LIST

FO

R G

RA

-ELI

-4X

(GRA-ELI-4X) ELITE 4’ EXTENSION PANEL BOX PACKING LIST

Y7

Y8

Y9

Y10

Y11

SIDE WALL PANEL

ROOF PANEL

UNDER ROOF VENT

ROOF VENT PANEL

ROOF PANEL


4

3

1

1

4

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

57 in / 1447 mm

30 5/8 in / 778 mm

8 7/8 in / 225 mm

19 1/8 in / 486 mm

30 3/8 in / 772 mm

602A

602B

603C

L08M-X

L08D-X

L08E-X

607-8X

607-XS

DP01

609-8X-R609-8X-L

609-XS

DP03

606-WS

610-8X-R610-8X-L

DP02

DP02B

630-8X-R630-8X-L

615

616

618

AZ-1 / W17S02/ML01

BZ-1

CZ-1

Z02

S04 / ML01

S06

56 9/16 in / 1437 mm

29 7/16 in / 748 mm

21 7/8 in / 555 m

61 in / 1550 mm

37 13/16 in / 960 mm

37 11/16 in / 957 mm

93 7/16 in / 2374 mm

ROOF CONNECTOR

ROOF CONNECTOR

93 7/16 in / 2374 mm

EAVE CONNECTOR

630 CONNECTOR CAP

21 3/4 in / 553 mm

93 7/16 in / 2374 mm

GUTTER BRACKET

GUTTER BRACKET

93 7/16 in / 2374 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

19 11/16 in / 500 mm

86 1/4 in / 2190 mmEXTENSION SUPPORT

56 1/2 in / 1435 mmROOF SUPPORTS

23 5/8 in / 600 mmEAVE SUPPORTS


M6*14

M4*10ATTACHES DP01 TO 607

(GRA-ELI-8XA) ELITE 8’ EXTENSION ALUMINUM PACKING LIST


8

16

2

2

2

2

1

1

1

4

4

2

8

2

2

2

2

2

2

4

2

4

6

9

90

3

75

PAR

TS

LIST

FO

R G

RA

-ELI

-8X

A

S07

S08

S09

W04

W14

HQC01

HQC02

Z04, S04/ML01

M5*8SCREW FOR DP02 AND DP02B



CONNECTOR FOR 603C

L08M-X BRACKET

ROOF VENT ARM

ROOF VENT LATCH

ROOF VENT HARDWARE


5

5

20

4

2

2

2

4

(GRA-ELI-8XA) 8X GRANDIO ELITE ALUMINUM PACKING LIST

76

PAR

TS

LIST

FO

R G

RA

-ELI

-8X

A

77

PAR

TS

LIST

FO

R G

RA

-ELI

-8X

P

(GRA-ELI-8XP) GRANDIO ELITE 8 EXTENSION PANEL BOX PACKING LIST

Y7

Y8

Y9

Y10

Y11

SIDE WALL PANEL

ROOF PANEL

UNDER ROOF VENT

ROOF VENT PANEL

ROOF PANEL


8

6

2

2

8

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

22 3/4 in / 578 mm

57 in / 1447 mm

30 5/8 in / 778 mm

8 7/8 in / 225 mm

19 1/8 in / 486 mm

30 3/8 in / 772 mm

601A-B

601A-FL

601A-FR

601B

602A

602B

602C

602D-R

602D-L

603C

603D

603E

619 PACK619-BAR

S19 SCREWS10 / ML02

2

1

1

8

6

12

1

1

1

8

1

1

1 - 6191 - 619 Bar

5 - S19 Screws3 - S10 / ML02

72 3/16 in / 1833 mm BACK WALL

18 1/4 in / 463 mm BACK WALL

70 3/4 in / 1797 mm FRONT RIGHT DOOR

70 3/4 in / 1797 mm FRONT LEFT DOOR

24 3/16 in / 614 mm

94 1/4 in / 2394 mm44 1/2 in / 1130 mm

M4*10M6*16 / Nut

69 11/16 in / 1770 mm

69 11/16 in / 1770 mm

69 11/16 in / 1770 mm

21 7/16 in / 545 mm

21 7/16 in / 545 mm

21 7/16 in / 545 mm

52 1/4 in / 1327 mmCROSS SUPPORT

DOOR

DOOR HANDLES

(GRA-ELI-BD) GRANDIO ELITE BACKDOOR PACKING LIST

603D

603E

604R

604L

L08D

619619-BAR

S19 ScrewS10 / ML02

622

622-R

622-L

620

623A

623B

L08A-X

J08A

622-DOORHANDLES

Z01

S04/ML01

S02/ML01

L21

J07

L28 / WASHER

W04

W04-1

W04-2

Y3-1

Y3-2

Y2-1

Y2-2

Y6

1/4 DB


1

1

1

1

2

1 - 6191 - 619 Bar

5 - S19 Screws3 - S10 / ML02

2

1

1

2

2

2

2

4

4


13

35

4

1

2

2/2

1

2

2

1

1

1

1

4

1


M6*10

M6*25

95 1/2 in / 2425 mm

L21 ENDCAP

19 9/16 in / 497 mm 4mm WASHERS

CONNECTOR BRACKET

FRAME CONNECTOR

FRAME CONNECTOR

UPPER ROOF PANEL

UPPER ROOF PANEL

BACK WALL SIDE

BACK WALL SIDE

DOOR PANELS

1/4” DRILL BIT

78

PAR

TS

LIST

FO

R G

RA

-ELI

-BD

24 3/16 in / 614 mm

52 1/4 in / 1327 mm

51 3/16 in / 1300 mm

61 1/32 in / 1550 mm

37 13/16 in / 960 mm

38 11/16 in / 957 mm

FRONT & BACK

FRONT & BACK

ROOF LINE

BACK WALL

CONNECTOR



Grandio Greenhouse Limited Lifetime Warranty

1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warranted for life. The word “defects” is de�ned as imperfections that impair the use of the product.

2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installa-tion, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.

3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the greenhouse or its components are not covered under this warranty.

4. This warranty does not cover scratching or scu�ng of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use will void this warranty.

5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.

6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.

7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this product. This warranty gives you speci�c legal rights, and you may also have other rights that vary from state to state.

79

WA

RR

AN

TY

NOTES NOTES


®

GREENHOUSE USER MANUALKEEP IN A SAFE PLACE FOR REFERENCE

CONTACT US IF YOU NEED HELPOR

HAVE MISSING OR DAMAGED PARTS

GRANDIOGREENHOUSES.COM

BACKYARD LIVING SOURCE, INC.9543 W. EMERALD ST., SUITE 101

BOISE, ID 83704

1-866-448-8231

Grandio Elite 8x12, 8x16, 8x20 & 8x24 Models

gra eli 8x12 thru 8x24 april 15...

Documents