design of triple effect evaporator for glycerol

8/13/2019 Design of Triple Effect Evaporator for Glycerol

1/37

DESIGN OF A TRIPPLE EFFECT FORWARD FEED EVAPORATOR FOR THE

CONCENTRATION OF GLYCEROL SOLUTION:

Design: Glycerol solution is to be concentrated from 7Wt% to a final concentration of 80Wt% The

feed is available at 50993 Kg/Hr and 27C. Steam is supplied at 103.66Kpa (Abs.) to the first effect

and a vacuum of 74.2(Abs.) mm of Hg is maintained in the last effect. Heat losses by radiation and

by entertainment are neglected. Condensate are assumed to enter each effect at its saturation

temperature.

Glycerol in feed = 50993 0.07

= 3569.51 Kg/Hr

Feed rate WF= 50993/3600

= 14.16 Kg/Sec

Bottom outlet from third effect = 3569.51/(0.83600)

= 1.24 Kg/Sec

Total evaporation =14.16 1.24

=12.9 Kg/Sec

Assuming equal evaporation in all the three effects.

W1 Evaporation rate in first effect

W2- Evaporation rate in second effect

W3 Evaporation rate in the third effectW1= W2 = W3 = (12.9/3) = 4.3 Kg/sec

Outlet from first effect = WF- W1

= 14.16 4.3

= 9.86 Kg/sec

Outlet from second effect = WF W1- W2

= 14.16 4.3 4.3

= 5.56 Kg/sec

Outlet from third effect = WF W1 W2 W3

= 14.16 4.3 4.3 4.3

= 1.26 Kg/sec

Concentration of glycerol in outlet from first effect = (14.16 0.07 )/ 9.86

= 10 wt%


2/37

Concentration of glycerol in outlet from second effect = (14.16.07)/5.56

= 0.178

= 17.8 wt%

Concentration of glycerol in outlet from third effect = (14.16.07)/1.26

= 0.79

= 79 wt%

Saturation temperature of inlet steam TS= 100C

Boiling point of water in the third effect = 12C

Temperature difference =100 12

= 88C

BOILING POINT RISE FOR GLYCEROL SOULTION

1) BPR for the third effect at 79 Wt% glycerol = 10.4C

2) BPR for the second effect at 17.8 Wt% glycerol = 1.5C

3) BPR for the first effect at 10 Wt% glycerol = 0.5C

Sum of the BPR of the glycerol solution = 10.4 + 1.5 + 0.5

= 12.4C

Effective temperature difference = 88 12.4

= 75.6C

Now we assume that the amount of heat transfer from steam to the solution is the same in all the

three effects i.e. Q (heat transfer in the first effect) = Q (heat transfer in the second effect) = Q

(heat transfer in the third effect)

OVERALL HEAT TRANSFER COEFFICIENT

Since it is a vertical effect evaporator, the overall heat transfer coefficient can safely be assumed as

follows:

In the first effect U1= 2325 W/mC

In the second effect U2= 1275 W/mC

In the third effect U3= 1031 W/mC

Now as we have assumed heat transfer rates to be equal , we have

Q1= Q2= Q3

(U1A1t1 ) = (U2A2 t2 ) = (U3A3t3)


3/37

We design the triple effect evaporator such that the heating area in all the three effect

is the same

A1= A2= A3

U1t1 = U2 t 2= U3t3

t2/ t1= U1/ U2

= 2352 / 1275

= 1.8

t3/ t 2= U2/ U3

=1275 / 1031

= 0.6

t1+ t2+ t3= 75.6C

0.6 t2+ t2+ 0.6 t2= 75.6C

t2= 32.3C

t1= 21.54C

t3= 21.64C

ACTUAL BOILING POINTS IN EACH EFFECT

First effect:

T1= TS - t1

= 100 - 21.54

= 78.54C

Second effect:

T2= T1- (BPR)1- t2

= 78.5 - 0.5 - 32.3

= 45.7C

Third effect:

T3= T2- (BPR)2- t3

= 45.7 - 1.5 - 21.64

= 22.56C


4/37

Effect 1 ( C ) Effect 2 ( C ) Effect 3 ( C ) Condenser ( C )

TS = 100 T1 = 78 T2 = 44.2 T3 = 12.16

T1= 78.5 T2 = 45.7 T3 =22.56

HEAT BALANCE

FIRST EFFECT:

WSS+ WFHF = W1H1+ ( WF - W1) h1

latent heat of steam S= 2257.86 KJ/ kg

HFEnthalpy of feed at inlet temperature ( 27C) = Cpf ( Tf - 0)

= ( 0.576 4.18) 27

= 65 KJ / Kg

H1- Enthalpy of vapor leaving the first effect = H2S+ (Cp)steam (BPR1)superhea

= 2640 + (1.884 0.5)

= 2487 KJ/ Kg

H2s- Enthalpy of steam at 78C = 2640 KJ / Kg

(Cp)steamat 78C = 1.884 KJ/ Kg

h1- enthalpy of outlet from first effect at 78.5C = Cp1( t10 )

= 0.65 4.18 78.5

= 213.28 KJ/Kg

WS (2257.86) + (14.16 65) = ( W1 2487 ) + ( 14.16 W1) 213.28

WS(2257.86) = 2273.7 W1 + 2099.6

WS= W1 + 0.93 ------------------------(1)


5/37

SECOND EFFECT:

W11+ ( WFW1) h1 = W2H2 + ( WFW1W2) h2

Latent heat of steam at 78C 1= H1- h2S

= 2487 - 325

= 2162 KJ /Kg

H3S Enthalpy of steam vapor at 44.2C = 2580 KJ /Kg

H2 - Enthalpy of vapor leaving the second effect = H3S+ ( Cp)steam (BPR2)supreheat

= 2580 + ( 1.884 1.5 )

= 2583 KJ/Kg

h2-Enthalpy of outlet from the second effect at 45.7C = Cp2( t2 - 0 )

= 0.6 4.18 45.7

= 114.62 KJ /Kg

W1 2162 + ( 14.16 W1) 213.28 = (W22583 ) + ( 14.16 W1W2)114.62

2063.34 W1 = 1397 + 2468.38 W2

W1 + 0.667 = 1.196 W2-------------------(2)

THIRD EFFECT:

W22+ (WFW1W2) h2 = W3H3 + (WFW1 - W2 - W3) h3

Latent heat of steam at 44.2C 2 = H2 - h3S

= 2583 - 190

= 2393 KJ / Kg

H4S-Enthalpy of steam vapor at 12 .16C = 2523 KJ/Kg

H3-Enthalpy of vapor leaving the third effect = H4S+ (Cp)steam (BPR3)ssuperheat

= 2523 + (1.884 10.4 )

= 2543 KJ/ Kg

h3Enthalpy of outlet from third effect at 22.56C = Cp3( t3 - 0)


6/37

= 0.57 4.18 22.56

= 53.75 KJ /Kg

W2 2393 + (14.16 W1W2) 114.62 = W3 2543 + ( 14.16 W1W2W3) 53.75

2332.13 W2- 60.87 = 2489.25 W3 + 861.92

W2+ 0.370 = 1.067 W3 + 0.026 W1--------------------(3)

W1+ W2+ W3 = 12.9 Kg/ Sec -------------------------(4)

Solving equations' (1),(2),(3) and (4), we get:

WS= 5.153 Kg/sec

W1= 4.223 Kg/sec

W2= 4.089 Kg/sec

W4= 4.588 Kg/sec

Now, Q1= WSS

=11634.75 KJ/sec

But Q1=U1A1t1

Therefore A1= (11634.75103)/(21.542325)

= 232.32 m2

Q2= W11

= 9130.13 KJ/sec

But Q2 = U2A2t2

Therefore A2 = (9130.13103)/(32.31275)

= 228 m2

Q3= W22

= 9784.98 KJ/sec

But Q3 = U3A3t3

Therefore A3= (9784.98103

)/(21.641031)

= 235 m2

Thus the obtained areas are within the acceptable range of 5% difference

Therefore the average area per effect of the evaporator is 232 m2.


7/37

Tube details:

Most generally used diameters today ranges from 1.25 to 2.00 in. outer diameter and most generally

used lengths of tubes ranges from 4 to 15 ft.

Let us choose 5/4-in. nominal diameter, 80 schedule, brass tubes of 10-ft length.

Therefore Outer diameter do= 42.164 mm

Inner diameter di= 32.46 mm

Length L = 10 ft

= 3.048 m

Tube pitch ()PT= 1.25 do

= 1.25 42.164

= 52.705 mm

Surface area of each tube a = doL

= 52.70510-33.048

= 0.4037 m2

Number of tubes required Nt= A /a

= 619

Area occupied by tubes = Nt(1/2) PT PTsin

= 619 0.5 (52.705 10-3)20.866

= 0.7445 m2

Where = 60o

But actual area is more than this. Hence this area is to be divided by factor which varies from 0.8 to

1.0.

Let us choose this factor as 0.9.

Therefore actual area required = 0.7445/ 0.9

= 0.827 m2

The central downcomer area is taken as 40 to 70% of the total cross sectional area of tubes. Let us

take it as 50%.

Therefore Downcomer area = 0.5 [Nt(/4) do2]

= 0.5 [619 (/4) (0.04216)2]

= 0.432 m2

Downcomer diameter = (4 0.432) /


8/37

= 0.742 m

Total area of tube sheet in evaporator = downcomer area + area occupied by tubes

= 0.432+ 0.827

= 1.259 m2

Thus tube sheet diameter = (4 7.1025)/

= 1.27 m


9/37

MECHANICAL DESIGN OF EVAPORATOR:

Take standard vertical short tube evaporator (calendria type)

Data:

Evaporator drum operating under vacuum at 0.4163 bar

Amount of water to be evaporated = 15480 kg/hr

Heating surface required A = 232 m2

Steam is available to first effect at pressure of 1.03 bar.

Density of liquid (10 wt% glycerol) = 1019 kg/m3

Density of water vapour = PM/RT

= (0.4163 10518) / (8314 351)

= 0.258 kg/m3

Design pressure = 5% extra of maximum working pressure

= 1.05 1.03

= 1.082 bar

= 1.103 kgf/cm2

Material:

Evaporator low carbon steel

Tubes brass

Permissible stress for low carbon steel = 980 kg/cm2

Modulus of elasticity for low carbon steel = 19 105kg/cm2

Modulus of elasticity for brass = 9.5 105 kg/cm2

Conical head at bottom

Cone angle 120o

Conical head at top

Cone angle 120o

1) Calendria sheet thickness:

The thickness is given by

ts= (PDo) /(2fJ + P)

= (1.1031270) /[(2 980 0.85) +1.103]

= 0.84 mm

The actual thickness must be much more so as to allow for corrosion and give rigidity to the shell.


10/37

Therefore it may be taken as ts= 10 mm

2) Tube sheet thickness:

To find tube sheet thickness

K = [Ests(Do ts)] / [EtNttt(dott)]

Es= elastic modulus of shell

Et= elastic modulus of tube

Do- outside diameter of shell = 3 m

do- outside diameter of tube = 60.325 mm

ts- shell thickness = 12 mm

tt - tube wall thickness = 5.5 mm

Nt - number of tubes in shell = 2108

Therefore K = [19 10512 (127010)] / [9.5 105619 4.85 (42.164 4.85)]

= 0.027

F = [(2 + K) / (2 + 3 K)]

= [(2 + 0.027) / (2 + 3 0.027)]

= 0.99

The effective tube sheet thickness is given by

tts= FDo[(0.25 P) / f]

= 0.991270[(0.25 1.103) / 980]= 21 mm

with corrosion allowance the thickness may be taken as 25 mm.

4) Check for tube thickness:

The tube thickness is given by

tt = Pdi/ (2fJ P)

The permissible stress for brass = 538 kg/cm2and J = 1

Therefore tt= (1.103 32.46) / [(2 538 1) 1.103]

= 0.033 mm

But provided thickness is 4.85 mm.Therefore chosen tubes have enough strength to withstand within

operating conditions.


11/37

5) Evaporator drum diameter:

The following equations help to determine the drum diameter. The diameter of the drum may be

same as that of the calendria. However it is necessary to check the size from the point of satisfactory

entrainment separation.

Rd= (V/A) / [0.0172 {(l- v) / v}]

Where V volumetric flow rate of vapour in m3/sec

A cross sectional area of drum

For drums having wire mesh as entrainment separator device, Rd may be taken as 1.3.

A = V / [Rd0.0172 {(l - v) / v}]

= [15480 /(3600 0.258)] / [1.3 0.0172 {(1019 0.258)/0.258}]

= 11.87 m2

Therefore drum diameter = {(4 11.87) /3.14}

3.89 m

Which is very large and therefore taking the drum diameter same as that of calendria.i.e 1.27 m

Drum height can be taken as 2 to 5 times of tube sheet diameter.

Thus drum height = 21.27

= 3.81 m

5) Drum thickness:

Drum is operating at 0.4163 bar. Design is therefore based on an external pressure of 1.7856 kg/cm2

(Design pressure).

Assume thickness of 15 mm.

The critical external pressure is given by

Pc = [2.42E (t /Do)2.5] / [(1 - 2)3/4 {(L /Do) 0.45 (t / Do)0.5}]

= [2.42 19 105(10 /1290)2.5] / [(1 0.322)3/4{(3810 /1290) 0.45 (10 /1290)0.5}]

= 8.96 kg/cm2

Pa = Pc / 4= 2.24 kg/cm2

According to IS 2825 (Appendix F)

L /Do =3.81/ 1.27

= 3

Do / t = 1270 /10


12/37

= 85

Therefore factor B = 10878

Pa= B / [14.22 (Do / t)]

= 10878/ [14.22 85]

= 9 kg/cm2

Here Pais greater than design pressure.

Assume thickness as 15 mm.

6) Flange calculation:

Flange material = IS:2004 1962 class 2

Bolting steel = 5% Cr Mo steel

Gasket material = asbestos composition

Outside diameter of calendria = 1290 mm

Calendria sheet thickness = 10 mm

Inside diameter of calendria = 1270 mm

Allowable stress of flange material = 100 MN/m2

Allowable stress for bolting material = 138 MN/m2

Determination of gasket width

do / di = [(y Pm) /{y P(m + 1)}]0.5

Assuming gasket thickness of 3.2 mmTherefore y = 11.0, m = 2, P = 0.11 MN/m2

do / di = [(11 0.11 2) /{11 0.11 (2 + 1)}]0.5

= 1.005

Let di of gasket equals 1300 mm i.e. 10 mm larger than calendria diameter, then

do= 1.3065 m

Minimum gasket width 2b = (1.3065 1.300) /2

= 3.2510-3m

Basic gasket seating width, bo = 12 / 2

= 6.0 mm

Diameter at location of gasket load reaction is, G = di + N

= 1300 + (3.2510-3)

= 1300 mm


13/37

Estimation of bolt loads

Load due to design pressure

H = (/4)G2P

= (/4) (1.3)20.11

= 0.15 MN

Load to keep joint tight under operation

Hp = G(2b)mP

= 1.3(3.2510-3)20.11

= 2.92 103 MN

Total operating load Wo = H + Hp

= 0.15+2.92 103

= 0.153 MN

Load to seat gasket under bolting up condition Wg = Gby

= 3.046 (3.2510-3/2) 11

= 0.17 MN

Here Wgis larger than Woand therefore, controlling load = 0.17 MN

Calculation of minimum bolting area:

Am= Ao= Wg/So= 0.17/138

= 1.23 10-3m2

Consider the bolt size as M 20 2

Therefore root area = 210-4m2

Number of bolts required = (1.23 10-3) / (2 10-4)

= 8

Flange thickness:

An approximate value of flange thickness may be given by

tF= G{P/(kf)}Where,

k = 1/ [0.3 +{(1.5WmhG) /(HG)}]

Wm- total bolt load = 1.2894 MN

hG= (BG) / 2


14/37

Where B is minimum pitch circle diameter.

B=G +12 +(220)

= 1300+12 + 40

= 1352 m

Therefore hG= (1352 1300) / 2

= 26

H = 1.25 MN

= 127421 kg

G = 1300 mm

Therefore k =1 / [0.3 + {(1.5 131437.31 26) / (127421 1300)}]

= 3.02

Hence tf= 1300{1.103/(3.02 1019)}

= 24.61 mm

Therefore use thickness of 30 mm including corrosion allowance.

7) Bracket design:

Data:

Diameter of vessel = 1270 mm

Height of vessel = 3.81 m

Clearance from vessel bottom to foundation = 1000 mm (assumed)Density of carbon steel = 7820 kg/m3

Density of brass = 8450 kg/m3

Wind pressure =128.5 kg/m2

Number of brackets = 4

Diameter of bolt circle = 3.15 m

Height of bracket from foundation = 2.25 m

Permissible stress for structural steel (IS 800)

Tension = 1400 kg/cm2

Compression = 1233 kg/cm2

Bending = 1575 kg/cm2

To find weight of vessel with contents:

Weight of vapour drum = dLt


15/37

= 1.27 3.810.015 7820

W1= 1783 kg

Weight of tubes W2= (/4)Nt(do2di

2) L

= (/4) 619(0.042220.032462) 3.0488450

= 9150 kg

weight of tube sheet W3= 2 (/4)Ds2 t

= (/4) 1.2720.025 7820 2

= 495 kg

Therefore total weight W = W1+ W2+ W3

= 10728 kg

a) Base plate:

Taking suitable base plate size, a = 140 mm, B = 150 mm

Maximum total compressive load is given by

P = [{4Pw(H f)} / (nDb)] + [W / n]

Where Pw - total force acting on vessel due to wind = kPhDo

k = 0.7

P - wind pressure = 128.5 kg/m2

h - height = 3.81 m

Thus Pw= 0.7 128.5 3.81 1.27

= 435.2 kg/m2

H - height of vessel above foundation =1.27 m

f - vessel clearance from foundation = 0

n - number of brackets = 4

Dbdiameter of bolt circle = 1.65 m

Hence compressive load,

P = [{4 435.2(1.270)}/ (4 3.15)] + [10728/ 4]= 2857 kg

Average pressure on the plate:

Pav = P / (a B)

= 2857 / (14 15)

=13.6 Kg/cm2


16/37

But f = 0.7 Pav (B2/ T12) {a4/ (a4+ B4)}

= 0.7 13.6 (152/ T12) {144(144+ 154)}

= 997.2 / T12

Therefore T12= 997.2 / 1575

= 0.63mm

T1= 0.8 mm

Use 6 mm thick plate.

b) Web plate:

Bending moment of each plate = (19532.25 / 2) {(3.15 3) / 2} 100

= 73246 kg cm

Stress at the edge = f = (3 P C) / (T2h2)

= (73246 / 0.707) / (T2 14 14)

1575 = 528.58 / T2

Therefore T2= 0.3356 cm = 3.356 mm

T2may be taken as 4 to 6 mm.

c) Column support:

It is proposed to use a channel section as column.

Size 150 75

Area of cross section = A = 20.88 cm2

Modulus of section = Zyy= 19.4 cm2

Radius of gyration = ryy = 2.21 cm

Weight of section = 16.4 kg/m

Height from foundation = l = 2.25 m

Equivalent length for fixed ends = le = l 2 = 2.25 2 = 1.125 m

Slenderness ratio = le r = (1.125 100) 2.21 = 51.0

Now if the load is acting eccentric on a short column, the maximum combined bending and directstress is given by

f = [W (A n)] + [(W e) (n Z)]

= [71861 (20.88 4)] + [(71861 7.5) (4 19.4)]

= 7805.73 kg/cm2


17/37

The permissible compressive stress is

f = [W (A n)] [1 + a (le r)2] + [(W e) (n Z)]

= [71861 (20.88 4)] [1 + (5127500)] + [(71861 7.5) (4 19.4)]

= 8104.12 kg/cm2

The calculated values are less than the permissible compressive stress and hence the channel selected

is satisfactory.

d) Base plate for column:

The size of column is 150 75. It is assumed that the base plate extends 20 mm on either side of the

channel.

Width = 0.8 75 + 2 20

= 100 mm

Length = 0.95 150 + 2 20

= 182.5 mm

Bearing pressure on each plate Pb= P /(B C)

= 19532.25 / (10 18.25)

= 107.03 kg/cm2

This is less than the permissible bearing pressure for concrete.

Stress in the plate = [(107.03 / 2) (202/102)] / (t2/ 6)

= 12.84 / t2kg/cm2

But f = 1575 kg/cm2

Therefore t2 = (12.84 / 1575) 100 mm2

t = 0.8152 mm

It is usual to select a plate of 4 to 6 mm thickness.

CONDENSER:


18/37

Design:The condenser is a horizontal condenser designed to condense 7652 Kg/Hr of 98% vapour of

glycerine at 1 atm pr. and 190C .The coolant used is water which is supplied in the tube side at an

inlet temperature of 20C and leaves at an outlet temperature of 35C.

Heat of vapourisation of glycerine = 18170 cal./mole

= 18170 4.18 92 J/Kg

= 6987.46 KJ/Kg

Amount of heat removed from the vapour Q = m

= (7652/3600) 6987.461000

= 14852.23 KJ/sec

AMOUNT OF WATER TO BE CIRCULATED:

(m)WCpt = (m)G

(m)W4.187(35-20) = 14852.23 KW

(m)W= (14852.231000) / (4.18715)

(m)W = 236.48 Kg/Sec

Amount of water required = 236.48 Kg/sec

LOGARITHMIC MEAN TEMPERATURE DIFFERENCE:

LMTD = ((190-20)-(190-35))/(ln ((190-20)/(190-35)))

= (170 - 155 )/ (ln (170/155))

= 162.36C

OVERALL HEAT TRANSFER COEFFICIENT:

Assume U = 600 W/m2k

Total heat transfer area A = Q/(U (t)LMTD)

= 14852.23/(600 162.38)

= 152.45 m2

Choose tubes of 5/4O.D.,16 BWG ,length of 16 ft laid on a 25/16square pitch.

Heat transfer area A = 152.45 m2

Number of tubes Nt = 152.45/(1.25 0.0254 (4.88-0.05))

= 317

From tube count table,

For tube O.D. of 5/4" on 25/16" square pitch


19/37

TEMA P or S

No. of passes = 2

Nearest no. of tubes Nt= 310

I.D. of shell = 889 mm

Corrected heat transfer area = n dL

=310 3.14 0.03175 4.88

= 150 m2

Corrected U = (14852.231000)/(150 162.38)

= 614 W/m2k

SHELL SIDE HEAT TRANSFER COEFFICIENT

CONDENSING VAPOUR SIDE:

Temperature of vapour coming in = 190C

Average temperature of water = (20 + 35 )/2

= 27.5C

Wall temperature = (190 + 27.5 )/2

=108.75C

Film temperature = (190 + 108.75)/2

=149.38C

So the property of water are taken at 149C

viscosity = 1.6103Ns/m2

Thermal conductivity K = 0.670 W/mC

Density =1175 Kg/m3

Specific heat Cp = 3.05 KJ/KgC

Mass flow rate per unit length = W/(Nt2/3 L)

=7652/(36003102/34.88)

=9.568103Kg/m sec

Renolds number Nre= (49.568103)/(1.6103)

= 23.92

Outer film coefficient hc =1.51(K32g /2)2/3(Nre

1/3)

hc=1.51(0.300813806259.81/2.56106)2/3(23.921/3)

= 1808.3 W/m2k


20/37

TUBE SIDE HEAT TRANSFER COEFFICIENT:

Average temperature of water =27.5C

Physical properties of water at 27.5C

Specific heat Cp4.18 KJ/KgC

Viscosity = 0.9103 Ns/m2

Thermal conductivity K = 0.616 W/mC

Prandtl number Pr= (Cp)/K

= 6.41

Mass velocity of water = 236.48 Kg/sec

at= (n0.0284)/(42)

= (3103.140.0284)/8

= 0.0492 m2/pass

Gt = mass velocity/at

= 236.48/0.0492

= 2806.5 Kg /m2sec

Inside diameter of the tube di= 1.12

= 0.0284 m

NRe = (diGt)/

= (0.02844806.5437)/(0.910

3

)= 15192 > 10000

Ditus boltern equation can be used

Nu = 0.023 (NRe)0.8(Pr)

0.3

= 0.023151920.86.410.3

= 561.17

hi = 4518 w/m2k

CALCULATED OVERALL HEAT TRANFER COEFFICIENT:

1/Uo= 1/ho+ 1/hi(do/di) +0.000528

= 1/1808.3 + 1/4518(1.25/1.12) +0.000528

= 0.000553+0.000247+0.000528

=0.001328

Uo= 753 W/m2k


21/37

Which is greater then the corrected U

Therefore this value of U is good enough.

PRESSURE DROP CALCULATIONS:

TUBE SIDE:

Nre= 15192

f = 0.079/(Nre)1/4

= 0.004

PL=(4fLv2/2gdi)g

vt= Gt/

= 4.82m/sec

PL= (40.0044.884.822/20.0284)997

=15.920 Kpa

PC= (2.5/2)vt2

=14.476 Kpa

PT= 2(PL+PC)

= 2(15.920+14.476)

= 60.8Kpa

This is within the permissible limit of a maximum pressure drop of 70Kpa in the tube side

So this pressure drop is acceptable.

SHELL SIDE:

Mass flow rate of glycerin =7652/3600

=2.13 Kg/sec

Saturation temperature of vapour Tvap=190C

Clearance C = pitch O.D.

= 25/16-5/4

= 7.94 mm

Pitch Pt = 25/16

= 0.04 m

as= (I.D)CB/Pt

Here I.D.=B=Ds-diameter of shell = 889 mm

as= 0.8890.8897.94103/0.04


22/37

= 0.157 m2

Equivalent diameter De= 4[Pt2-(do

2)/4]/( do)

= 4[0.042-(3.140.031752)/4]/(3.140.03175)

= 0.0324m

Gs= 2.13/0.157

=13.57 kg/sec m2

At 190C vapor viscosity vap=1.1105Ns/m2

(Nre)vap=GsDe/vap

=13.570.0324105/1.1

= 39970

f =1.87(Nre0.2)

=0.225

Density of vapour vap= 2.42 Kg/m3

Number of baffles Nb+1=L/Ds

=4.88/0.889

=5.5 i.e. 6

Therefore Nb=5

PS=2[(f(Nb+1)DsGs2g)/(gDevap)]0.5

=(0.22560.88913.572

)/(0.03242.42)=3194.4 pa

=3.194 Kpa

This is also within the permissible limit of a maximum pressure drop of 14 Kpa

So this is acceptable.

MECHANICAL DESIGN OF CONDENSER:

SHELL SIDE:


23/37

Material : Carbon steel

No. of shells : 1

No. of passes : 2

Fluid : 80 % Glycerine vapour

Internal diameter : 889mm

Working pressure : 0.1 N/mm2

design pressure : 0.11 N/mm2

Inlet temperature : 190C

Outlet temperature: 190C

Allowable stress : 950 Kg/Cm2

TUBE SIDE:

Material : Stainless steel (IS grade 10)

No. of tubes : 310

Outside diameter : 31.75 mm

Length : 4.88 m

fluid : water

pitch : 39.69 mm (square)

Allowable stress : 10.06 Kg/m2

working pressure : 1.033 Kg/cm2

Design pressure : 1.55 Kg/cm2

Inlet temperature : 20C

Outlet temperature : 35C

SHELL SIDE:


24/37

SHELL THICKNESS:

ts = (PdDS)/(2fJ-Pd)

= (0.11889)/((2950.85)-0.11)

= 0.61 mm

But minimum thickness of shell is 6 mm

Therefore with corrosion allowance of 2mm

Thickness of shell = 8 mm

NOZZLE DIAMETER

M = Mass velocity/sec

= 7652/3600

= 2.13 Kg/sec

Density =1175 kg/m3

Assume velocity to be 10 m/sec

(dn2v)/4 = M

dn2= (2.134)/(103.141175)

dn=0.015 m

NOZZLE THICKNESS

tn= (Pddn)/(2fJ-P)

= (0.1115)/(2950.85-0.11)= 0.10 mm

Nozzle thickness with corrosion allowance = 5 mm

HEAD THICKNESS:

th= (PdRcW)/(2fJ)

W = (1/4)(3+(Rc/RK)1/2 )

Rc- crown radius 80% of shell I.D. = 711.2 mm

RK- Knuckle radius 10% of shell I.D.= 88.9 mm

W = 1.46

th =0.71 mm

Using same thickness as that of the shell = 8 mm

BAFFLE ARRANGEMENT:


25/37

Tansverse bafffles

Number of baffles =5

Baffle Spacing = Ds= 889 mm

Thickness of baffles = 6 mm

Height of baffle = 0.75 Ds

= 666 mm

TIE RODS AND SPACERS:

For shell diameter Ds= 889 mm

No. of tie rods = 6

Diameter of rods = 13 mm

FLANGE CALCULATION:

Flange material = IS:2004-1962 class 2

Bolting steel =5% Cr Mosteel

Gasket material =asbestos composition

Shell inside diameter =889 mm

Shell thickness ts= 8mm

Shell outside diameter = (2ts)+889

= (28) +889

= 905 mm

Allowable stress of flange material = 100 MN/m2

Allowable stress of bolting material = 138 MN/m2

GASKET WIDTH:

Go/Gi=[(y-Pdm)/(y-pd(m+1))]1/2

m-Gasket factor =2.75

y-Minimum design seating stress =25.5 MN/m2

Go/Gi= [25.5-(0.112.75)/25.5-(0.113.75)]1/2

= 1.0022

Minimum gasket width N =10 mm

Basic gasket seating width bo= N/2

= 5 mm< 6.3 mm

Let,inside diameter of gasket = inside diameter of shell = 889 mm


26/37

Gi= 889 +(28)

= 905 mm

Mean gasket width = Gi+N

= 915 mm

therefore G = 915 mm

Estimation of bolt load:

Load due to design pressure H = (G2Pd)/4

= (0.91520.11)/4

= 0.072 MN

Effective gasket sitting width b = bo= 5 mm since bWo, controlling load =0.367 MN

Minimum bolting area:

Total cross sectional area of bolt under operating condition Am1=Wo/Sb

Sb-nominal bolt stress at design temperature of 190C=138 MN/m2

Therefore Am1= 0.0807/138

= 0.000585 m2

Total cross sectional area of bolt required for gasket seating Am2=Wb/Sa

Sa-nominal bolt stress at ambient temperature (30C)=138 MN/m2

Therefore Am2= 0.367/138

= 0.00266 m2

Since Am2> Am1,Am = Am2= 0.00266 m2

Calculation of optimum bolt size:


27/37

C =2(R+g1)+B

Choosing bolt M-18 2

Total number of bolts = G/(18 2)

= 915/36

= 25

Actual number of bolts = 24

R-radial clearance from bolt circle to point of connection of hub and back of flange = 27 mm

B-inside diameter of flange = outside diameter of shell = 0.905 m

g1=go/0.707,let go= 8 mm

g1= 0.008

C = 2(0.027 + 0.008) + 0.905

= 0.975 m

Therefore bolt circle diameter = 0.975 m

Flange outside diameter:

A = C + bolt diameter + 0.02

= 0.975 + 0.018 + 0.02

= 1.013 m

Check of gasket width:

Ab-root area of bolt (m2)-1.54 10-4m2

Sg-allowable stress for bolting material at atmospheric temperature =138 MN/ m2

Therefore, AbSg/GN = 15.86

Since 15.86 > 2y

Condition is satisfied.

Flange moment computations:

Wo= W1+ W2+ W3(under operating condition)

W1= (B2Pd)/4

= (3.140.90520.11)/4

= 0.071 MN

W2= H W1

H =(G2Pd)/4

= (3.140.91520.11)/4


28/37

= 0.0732 MN

W2 = 0.0723 0.071

= 0.0013 MN

W3= WoH

= 0.0807 0.0723

= 0.0084 MN

Total flange moment ,

Mo= W1a1+ W2a2+ W3a3

a1= (C B)/2

= 0.035 m

a3 = (C-G)/2

= 0.03 m

a2= (a1+a2)/2

= 0.0325 m

Mo=0.0710.035 + 0.00130.03 + 0.00840.0325

= 2.78 10-3 MNm

Bolting up condition:

Total flange moment Mg= Wa3

W = (Am

+ Ab)S

g/2

= 0.00472138

= 0.651 MN

a3= 0.03 m

Therefore Mg = 0.01953 MNm

= 19.5 10-3 MNm

Since Mg> Mofor moment under operating condition,Mgis controlling.

Therefore M = Mg= 19.510-3MNm

Flange thickness:

t2= (MCFY)/BST

K =A/B

= Outer diameter of flange/ inner diameter of flange

= 1.013/0.905


29/37

= 1.12

Y =14

Assume CF =1

Therefore thickness 't' = 0.055 m

Actual bolt spacing BS=C/n

= (3.140.975)/24

= 0.128 m

Bolt pitch correction factor CF =[BS/(2d+t)]1/2

=[0.128/(20.018+0.055)]1/2

=1.19

Therefore CF1/2= 1.091

Actual flange thickness = CF1/2t

= 1.0910.055

= 0.06 m

= 60 mm

TUBE SIDE:

TUBE THICKNESS:

tt=Pdo/2fJ+P

J =1 for seamless tubeTherefore tt=(1.5531.75)/(21006+1.55)

= 0.024 mm

No corrosion allowance since the tube is made of stainless steel

Thickness of tube = 1mm

TUBE SHEET:

tS= FG[0.25P/f]1/2

F-The value of F varies according to type of heat exchanger,for most cases it is taken as 1

G =915 mm

Therefore tS=915[(0.251.55)/1006]1/2

= 17.96 mm

CHANNEL AND CHANNEL COVER:


30/37

t = G[KP/f]1/2

K = 0.3 for ring type gasket

Material of construction is carbon steel

So allowable stress f =950 Kg/cm2

Therefore t =915[(0.31.55)/950]1/2

= 20.24 mm

With corrosion allowance t = 25 mm

NOZZLE THICKNESS:

Assume inlet and outlet diameter = 75 mm

Thickness of nozzle th= Pd/2fJ-P

= (1.5575)/(20.85950-1.55)

= 0.0612 mm

With corrosion allowance thickness = 6mm

SADDLE SUPPORT DESIGN:

Material -Low carbon steel

Vessel diameter=905 mm

Length of shell =4.88 m

Torispherical head:

Crown radius =711.2 mm

Knuckle radius =88.9 mm

Working pressure =1Atm

Shell thickness = 8 mm

Head thickness = 8mm

Corrosion allowance = 2mm

permissible stress = 950 Kg/cm2

R-Vessel radius = 425.5

Distance of saddle center line from shell end A = 0.45R

= 203.63 mm < 0.2L

Longitudinal bending moment:


31/37

The bending moment at the support is;

M1=QA[1-{(1-A/L)+(R2-H2/2AL)/(1+4H/3L)}]

A =203.63 mm

Q =W/2[L+4H/3]

W-Weight of fluid and vessel.

Weight of shell material:

W1=[(Do2-Di

2)Lshell material] /4

shell material- 7700 Kg/m3

W1=[3.14(0.9052-0.8892)4.887700] /4

= 847 Kg

Weight of tubes:

W2= n[(Do2-Di2)Ltube material] /4

tube material-7800 Kg/m3

W2 =310[3.14(0.031752-0.02982)4.887800] /4

= 1112 Kg

Weight of tube sheet:

W3= (2D2t)/4

= (23.140.90520.01807800)/4

= 180 Kg

Liquid load in the shell:

W4=(shell volume -tube volume)liquid

=[(Ds2L)/4 - (ndo

2l)/4 ]1175

=[(0.90524.88)/4 - (3100.0317524.88) /4 ]1175

=(3.14 - 1.20)1175

= 2280 Kg

Liquid load in tubes:W5= ndi

2lliquid/4

=(3103.140.029824.88997)/4

= 1052 Kg

Therefore total weight WT= W1+ W2+ W3+ W4+ W5

= 847 + 1112 + 180 + 2280 + 1052


32/37

= 5471 Kg

Hence, Q =5471/2[4.88+(40.257)/3]

= 14287 Kgm

M1=(142870.20363)[1-{(1-0.20363/4.88)+(0.45252-0.2572/20.2034.88)/(1+40.257/34.88)}]

=2909.261[1-{(0.958+0.0698)/1.0702}]

=115.26 Kgm

The bending moment at the center of the span is given by:

M2=(QL/4)[{1+2(R2-H2)/L2}/{1+(4H/3L)}- (4A/L)]

=(142874.88/4)[{1+2(0.45252-0.2572)/4.882}/{1+(40.257/34.88)}- (40.203/4.88)]

= 17430[1.312 - 0.1664]

= 19968 Kgm

Stress in shell at the saddle:

At the top most fiber of the cross-section,

f1=M1/(K1R2t)

For an angle of 120,K1=0.107 m

t-thickness of shell = 8 mm

f1=115.6/(0.1073.140.452520.008)

=20.93 Kg/cm2

At the bottom most fiber of the cross-sectionf2=M1/(K2R

2t)

For an angle of 120,K2 =0.192 m

f2=115.6/(0.1923.140.452520.008)

=11.67 Kg/cm2

Stress in the shell at mid point:

f3=M2/(R2t)

=19968/(3.140.452520.008)

=388 Kg/cm2

Thus the values of stresses are within the limited range

Hence the designed support is acceptable.

COST ESTIMATION:

Glycerin plant size =100 T/day


33/37

Fixed capital investment for cost index of 130 = Rs 108

Cost index for 2002 = 402

Therefore present fixed capital investment =108(402/130)

=Rs 30,92,30,769

Estimation of total investment cost:

1) Direct cost:

a) Purchased equipment cost:(15 40% of FCI )

Assume 40% of FCI

=Rs 12,36,92,307

b) Installation cost:(35 45% of PC)

Assume 45%

=Rs 13,91,53,846

c) Instrument and control installed:(6 30% of PEC)

Assume 30% of PEC

=Rs 9,27,69,230

d) Piping installation cost:(10 80% of PEC)

Assume 75%

=Rs.23,19,23,076

e) Electrical installation cost:(10 40% of PEC)

Assume 40% of PEC

=Rs 12,36,92,307

f) Building process and auxilliary:(10-70% of PEC)

Assume 65%

=Rs 20,09,99,999

g) Service facilities:(30-80% 0f PEC)

Assume 75%

=Rs 23,19,23,076

h) Yard improvement:(10-15% of PEC)

Assume 15%

=Rs 4,63,84,615

i) Land:(4-8% of PEC)


34/37

Assume 8%

=Rs 2,47,38,461

Therefore direct cost =Rs 1,21,52,76,917

2) Indirect cost:

Expenses which are not directly involved with material and labour of actual installation or complete

facility

a) Engineering and supervision:(5-30% of DC)

Assume 30%

=Rs 36,45,83,075

a) Construction expenses:(10% of DC)

=Rs 12,15,27,691

b) Contractors fee:(2-7% 0f DC)

Assume 7%

=Rs 8,50,69,584

c) Contingency:(8-20% of DC)

Assume 10%

=Rs 12,15,27,691

Therefore total indirect cost =69,27,08,042

3) Fixed capital investment:

Fixed capital investment(FCI) = DC+IC

= Rs 1,90,79,84,959

4) Working capital investment:

10 20% of FCI

Assume 15%

=Rs 28,61,97,743

5) Total capital investment:

= FCI + WC

=Rs 2,19,41,82,703

Estimation of total product cost(TPC):

Fixed charges:


35/37

a) Depreciation:(10% of FCI for machinery)

=Rs 2,19,41,827

b) Local taxes:(3-4% of FCI)

Assume 3%

=Rs 6,58,25,481

c) Insurances:(0.4-1% of FCI)

Assume 1%

=Rs 2,19,41,827

d) Rent:(8-12% of FCI)

Assume 9%

=Rs 4,57,97,372

Therefore total fixed charges =Rs 15,55,06,507

But, Fixed charges = (10-20% of TPC)

Assume 10%

Therefore Total product cost =155506507/0.1

=Rs 1,55,50,65,070

Direct production:

a) Raw material:(10-50% 0f TPC)

Assume 30%

=Rs 46,65,19,521

b) Operating labour(OL):(10-20% of TPC)

Assume 15%

=Rs 23,32,59,760

c) Direct supervisory and electric labour:(10-25% of OL)

Assume 15%

=Rs 3,49,88,964

d) Utilities:(10-20% of TPC)

Assume 15%

=Rs 23,32,59,760

e) Maintainence:(2-10% of FCI)

Assume 6%


36/37

=Rs 9,33,03,904

e) Operating supplies (OS):(10-20% of maintainence)

Assume 15%

=Rs 1,39,95,585

f) Laboratory charges:(10-20% of OL)

Assume 15%

=Rs 3,49,88,964

g) Patent and royalties:(2-6% of TPC)

Assume 4%

=Rs 6,22,02,602

Plant overhead cost:

50-70% of (OL+OS+M)

Assume 60%

=Rs 20,43,35,549

General expenses:

a) Administration cost:(40-60% of OL)

Assume 55%

=Rs 12,82,92,868

b) Distribution and selling price:(2-30% of TPC)

Assume 15%

=Rs 23,32,59,760

c) Research and development cost:(3% of TPC)

=Rs 4,66,51,952

Therefore general expenses(GE) =Rs 40,82,04,580

Therefore manufaacturing cost(MC)= Product cost+fixed charges+Plant overhead expenses

= Rs 1,91,49,07,126

Total production cost:

Total production cost =MC + GE

=Rs 2,32,31,11,706

Gross earnings and rate of return:

The plant is working for say 300 days a year


37/37

Selling price =Rs. 97/kg

Total income =100300100097

=Rs 2,91,00,00,000

Gross income =Total income total product cost(1555065070)

=Rs 1,35,49,34,930

Tax =50%

Net profit =Rs 67,74,67,465

Rate of return = net profit/total capital investment

=30.87%

design of triple effect evaporator for glycerol

Documents