controllogix ethernet/ip bridge...

Installation Instructions

Original Instructions

ControlLogix EtherNet/IP Bridge ModuleCatalog Numbers 1756-ENBT, 1756-ENBTK

The ControlLogix EtherNet/IP bridge establishes communication between Logix 5000 controllers and communicates with various devices on the Ethernet network.

Topic Page

Install the Module 5

Network Connectors and Cable 5

Specifications 6

Additional Resources 6

ControlLogix EtherNet/IP Bridge Module

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

ATENCIN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la seccin Recursos adicionales acerca de la instalacin, configuracin y operacin de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalacin y cableado y con los requisitos de todos los cdigos, leyes y estndares vigentes.El personal debidamente capacitado debe realizar las actividades relacionadas a la instalacin, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el cdigo de prctica aplicable.Si este equipo se usa de una manera no especificada por el fabricante, la proteccin provista por el equipo puede resultar afectada.ATENO: Leia este e os demais documentos sobre instalao, configurao e operao do equipamento que esto na seo Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os usurios devem se familiarizar com as instrues de instalao e fiao alm das especificaes para todos os cdigos, leis e normas aplicveis. necessrio que as atividades, incluindo instalao, ajustes, colocao em servio, utilizao, montagem, desmontagem e manuteno sejam realizadas por pessoal qualificado e especializado, de acordo com o cdigo de prtica aplicvel. Caso este equipamento seja utilizado de maneira no estabelecida pelo fabricante, a proteo fornecida pelo equipamento pode ficar prejudicada.: , , , , . , . , , . , , , , , , , . , . :

ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt Weitere Informationenaufgefhrten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender mssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zustzlich mit den Installations- und Verdrahtungsanweisungen vertraut machen.Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung drfen nur durch ausreichend geschulte Mitarbeiter und in bereinstimmung mit den anwendbaren Ausfhrungsvorschriften vorgenommen werden.Wenn das Gert in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeintrchtigt sein.ATTENTION : Lisez ce document et les documents lists dans la section Ressources complmentaires relatifs linstallation, la configuration et le fonctionnement de cet quipement avant dinstaller, configurer, utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions dinstallation et de cblage en plus des exigences relatives aux codes, lois et normes en vigueur.Les activits relatives linstallation, le rglage, la mise en service, lutilisation, lassemblage, le dmontage et lentretien doivent tre ralises par des personnes formes selon le code de pratique en vigueur.Si cet quipement est utilis dune faon qui na pas t dfinie par le fabricant, la protection fournie par lquipement peut tre compromise. : , , , . , .

, , , , , , .

.ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione Altre risorse, riguardanti linstallazione, la configurazione ed il funzionamento dellapparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici e standard applicabili.Le attivit come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.Qualora lapparecchio venga utilizzato con modalit diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.DKKAT: Bu rnn kurulumu, yaplandrlmas, iletilmesi veya bakm ncesinde bu dokman ve bu ekipmann kurulumu, yaplandrlmas ve iletimi ile ilgili lave Kaynaklar blmnde yer listelenmi dokmanlar okuyun. Kullanclar yrrlkteki tm ynetmelikler, yasalar ve standartlarn gereksinimlerine ek olarak kurulum ve kablolama talimatlarn da renmek zorundadr.Kurulum, ayarlama, hizmete alma, kullanma, paralar birletirme, paralar skme ve bakm gibi aktiviteler sadece uygun eitimleri alm kiiler tarafndan yrrlkteki uygulama ynetmeliklerine uygun ekilde yaplabilir.Bu ekipman retici tarafndan belirlenmi amacn dnda kullanlrsa, ekipman tarafndan salanan koruma bozulabilir.

POZOR: Ne zanete instalovat, konfigurovat i provozovat tento vrobek nebo provdt jeho drbu, pette si tento dokument a dokumenty uveden v sti Dodaten zdroje ohledn instalace, konfigurace a provozu tohoto zazen. Uivatel se musej vedle poadavk vech relevantnch vyhlek, zkon a norem nutn seznmit tak s pokyny pro instalaci a elektrick zapojen.innosti zahrnujc instalaci, nastaven, uveden do provozu, uvn, mont, demont a drbu mus vykonvat vhodn prokolen personl v souladu s pslunmi provdcmi pedpisy.Pokud se toto zazen pouv zpsobem neodpovdajcm specifikaci vrobce, me bt naruena ochrana, kterou toto zazen poskytuje.UWAGA: Przed instalacj, konfiguracj, uytkowaniem lub konserwacj tego produktu naley przeczyta niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe rda omawiajce instalacj, konfiguracj i procedury uytkowania tego urzdzenia. Uytkownicy maj obowizek zapozna si z instrukcjami dotyczcymi instalacji oraz oprzewodowania, jak rwnie z obowizujcymi kodeksami, prawem i normami.Dziaania obejmujce instalacj, regulacj, przekazanie do uytkowania, uytkowanie, monta, demonta oraz konserwacj musz by wykonywane przez odpowiednio przeszkolony personel zgodnie z obowizujcym kodeksem postpowania.Jeli urzdzenie jest uytkowane w sposb inny ni okrelony przez producenta, zabezpieczenie zapewniane przez urzdzenie moe zosta ograniczone.OBS! Ls detta dokument samt dokumentet, som str listat i avsnittet vriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller brjar anvnda eller utfra underhllsarbete p produkten. Anvndare mste bekanta sig med instruktioner fr installation och kabeldragning, frutom krav enligt gllande koder, lagar och standarder.tgrder som installation, justering, service, anvndning, montering, demontering och underhllsarbete mste utfras av personal med lmplig utbildning enligt lmpligt bruk.Om denna utrustning anvnds p ett stt som inte anges av tillverkaren kan det hnda att utrustningens skyddsanordningar frstts ur funktion.LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert, configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in overeenstemming met de geldende praktijkregels.Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.

2 Rockwell Automation Publication 1756-IN019D-EN-P - September 2017


ATTENTION: Read this document and the documents that are listed in the Additional Resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.

In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the manufacturer for repair. Do not dismantle the module.

If this equipment is used in a manner that is not specified by the manufacturer, the protection that is provided by the equipment may be impaired.

This equipment is certified for use only within the surrounding air temperature range of 060 C (32140 F). The equipment must not be used outside of this range.

Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.

Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments.

This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure must have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5VA or be approved for the application if non-metallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain more information regarding specific enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more installation requirements.

NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.

WARNING: Special Conditions for Safe Use:

This equipment shall be mounted in an ATEX Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54 (in accordance with EN 60079-15) and used in an environment of not more than Pollution Degree 2 (as defined in EN 60664-1) when applied in Zone 2 environments. The enclosure must be accessible only by the use of a tool.

This equipment shall be used within its specified ratings that are defined by Rockwell Automation.

Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 140% of the peak rated voltage when applied in Zone 2 environments.

The instructions in the user manual shall be observed. This equipment must be used only with ATEX certified Rockwell

Automation backplanes. Secure any external connections that mate to this equipment

by using screws, sliding latches, threaded connectors, or other means provided with this product.

Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

IMPORTANT Any illustrations, charts, sample programs, and layout examples that are shown in this publication are intended solely for the purposes of example. Since there are many variables and requirements that are associated with any particular installation, Rockwell Automation does not assume responsibility or liability for actual use based on the examples that are shown in this publication.

Prevent Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when handling this equipment:

Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circuit components inside the equipment. Use a static-safe workstation, if available. Store the equipment in appropriate static-safe packaging when

not in use.

Rockwell Automation Publication 1756-IN019D-EN-P - September 2017 3
http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf


North American Hazardous Location Approval

The following information applies when operating this equipment in hazardous locations.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. When combining products within a system, the most adverse temperature code (lowest "T" number) may be used to help determine the overall temperature code of the system. Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

WARNING:Explosion Hazard Do not disconnect equipment unless power has been removed or the

area is known to be nonhazardous. Do not disconnect connections to this equipment unless power has

been removed or the area is known to be nonhazardous. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.

Substitution of components may impair suitability for Class I, Division 2.

If this product contains batteries, they must only be changed in an area known to be nonhazardous.

Informations sur lutilisation de cet quipement en environnements dangereux.

Les produits marqus "CL I, DIV 2, GP A, B, C, D" ne conviennent qu' une utilisation en environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livr avec des marquages sur sa plaque d'identification qui indiquent le code de temprature pour les environnements dangereux. Lorsque plusieurs produits sont combins dans un systme, le code de temprature le plus dfavorable (code de temprature le plus faible) peut tre utilis pour dterminer le code de temprature global du systme. Les combinaisons d'quipements dans le systme sont sujettes inspection par les autorits locales qualifies au moment de l'installation.

AVERTISSEMENT:Risque dExplosion Couper le courant ou s'assurer que l'environnement est class non

dangereux avant de dbrancher l'quipement. Couper le courant ou s'assurer que l'environnement est class non

dangereux avant de dbrancher les connecteurs. Fixer tous les connecteurs externes relis cet quipement l'aide de vis, loquets coulissants, connecteurs filets ou autres moyens fournis avec ce produit.

La substitution de composants peut rendre cet quipement inadapt une utilisation en environnement de Classe I, Division 2.

S'assurer que l'environnement est class non dangereux avant de changer les piles.

European Hazardous Location Approval

The following applies to products marked II 3 G. Such modules:

This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 2014/34/EU and has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in Zone 2 potentially explosive atmospheres, given in Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements is achieved by compliance with EN 60079-15 and EN 60079-0.

May have catalog numbers followed by a "K" to indicate a conformal coating option.

Waste Electrical and Electronic Equipment (WEEE)

At the end of its life, this equipment should be collected separately from any unsorted municipal waste.

Removal and Insertion Under Power

WARNING: When you insert or remove the module while backplane power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance that can affect module operation.

ATTENTION: This equipment is not resistant to sunlight or other sources of UV radiation.

WARNING: If you connect or disconnect the communications cable with power applied to this module or any device on the network, an electric arc can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

4 Rockwell Automation Publication 1756-IN019D-EN-P - September 2017


Install the ModuleYou can install or remove a module while chassis power is applied. For equipment with multi-point network communication connections. Follow these steps to install the module.

1. Set the network IP address on a module.

For more information about how to configure an EtherNet/IP network, see the EtherNet/IP Network Configuration User Manual, publication ENET-UM001.

Depending on the 1756 EtherNet/IP communication module, you can use some or all of these tools to set the network Internet Protocol (IP) address:

Rotary switches Bootstrap Protocol (BOOTP)/Dynamic Host

Configuration Protocol (DHCP) server RSLinx Classic software The Studio 5000 environment

The module uses these tools sequentially to set the IP address.

2. Determine module slot location.

3. Install the module.a. Align the circuit board with top and bottom guides in the

chassis.b. Slide the module into the chassis.

Make sure that the module backplane connector properly connects to the chassis backplane. The module is properly installed when it is flush with the power supply or other installed modules.

4. Connect the module to an EtherNet/IP network via an RJ45 connection.

5. The module is properly installed when it is flush with the power supply or other installed modules

6. Download the Add-on Profile from the Product Compatibility and Download website at http://www.ab.com.

7. Connect to the module via the USB port (if the module is equipped with a USB port).

8. Download the firmware from the Product Compatibility and Download website at http://www.ab.com.

9. Apply chassis power and check status indicators.

For more information on the status indicators, see the EtherNet/IP Modules Installation Instructions, publication ENET-IN002.

Network Connectors and Cable

8 ------ NC7 ------ NC6 ------ RD-5 ------ NC4 ------ NC3 ------ RD+2 ------ TD-1 ------ TD+

8

1

RJ45

Modules Ports Requirements

EtherNet/IP Copper Ethernet

Connector/cable: RJ45 connector according to IEC 60603-7, 2 or 4 pair Category 5e minimum cable according to TIA 568 B.1 or Category 5 cable according to ISO/IEC 24702

31276-M

Rockwell Automation Publication 1756-IN019D-EN-P - September 2017 5
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/enet-um001_-en-p.pdfhttp://ab.rockwellautomation.com/http://ab.rockwellautomation.com/http://literature.rockwellautomation.com/idc/groups/literature/documents/in/enet-in002_-en-p.pdf

Specifications

Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Rockwell Automation SupportFor technical support, visit http://www.rockwellautomation.com/support/overview.page.

Attribute 1756-ENBT, 1756-ENBTK

Temperature, operatingIEC 60068-2-1 (Test Ad, Operating Cold),IEC 60068-2-2 (Test Bd, Operating Dry Heat),IEC 60068-2-14 (Test Nb, Operating Thermal Shock)

0 C < Ta < +60 C (+32 F < Ta < +140 F)

Temperature, Surrounding Air, max 60 C (140 F)

All supply voltages or voltage ranges 5.1V DC, 700 mA24V DC, 3 mA

Isolation Voltage 30V (continuous), basic insulation type, Ethernet to backplaneType tested at 707V DC for 60 s

Wire sizeEthernet connections:RJ45 connector according to IEC 60603-7, 2 or 4 pair Category 5e minimum cable according to TIA 568 B.1 or Category 5 cable according to ISO/IEC 24702.

Enclosure type rating None (open-style)

North American temp code T4A

IEC temp code T4

Resource Description

EtherNet/IP Modules Installation Instructions, publication ENET-IN002 Provides details on how to install and configure EtherNet/IP communication modules.

Ethernet Design Considerations Reference Manual, publication ENET-RM002 Provides details about how to use EtherNet/IP communication modules with Logix5000 controllers and communicate with other devices on the EtherNet/IP network.

EtherNet/IP Network Configuration User Manual, publication ENET-UM001 Describes how you can use EtherNet/IP communication modules with your Logix5000 controller and communicate with various devices on the Ethernet network.

EtherNet/IP Embedded Switch Technology Application Guide, publication ENET-AP005Provides details about how to install, configure, and maintain linear and Device Level Ring (DLR) networks by using Rockwell Automation EtherNet/IP devices that are equipped with embedded switch technology.

EtherNet/IP Media Planning and Installation ManualThis manual is available from the Open DeviceNet Vendor Association (ODVA) at http://www.odva.org

Provides details about how to use the required media components and provides information on how to plan for, install, verify, troubleshoot, and certify your EtherNet/IP network.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website,http://www.rockwellautomation.com/global/certification/overview.page Provides declarations of conformity, certificates, and other certification details.

Allen-Bradley, ControlLogix, Logix 5000, Rockwell Automation, Rockwell Software, RSLinx, and Studio 5000 are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6 34752 erenky, stanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website athttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 1756-IN019D-EN-P - September 2017 PN-468269Supersedes Publication 1756-IN019C-EN-P - November 2004 Copyright 2017 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.pagehttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://www.rockwellautomation.com/global/certification/overview.pagehttp://www.rockwellautomation.com/global/literature-library/overview.pagehttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/enet-in002_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/rm/enet-rm002_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/enet-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/ap/enet-ap005_-en-p.pdfhttp://www.odva.orgControlLogix EtherNet/IP Bridge Module Installation InstructionsInstall the ModuleNetwork Connectors and CableSpecificationsAdditional ResourcesBack CoverIntroduction_Category TypesThis tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released as JIT (print on demand) or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.Publication Type and Print CategoryPublication TypeOff Set Print Category Spec. (See table below)JIT Spec. (See table below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release OptionADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / InternalAPA3D2Application Solution or Customer Success Story5100Presale / ExternalARNANAArticle/Editorial/BylineNANAPresale / Internal(press releases should not be checked into DocMan or printed)ATB3, B4D5Application techniques5100Presale / ExternalBRA2 Primary, A1NABrochures5100Presale / ExternalCAC2 Primary, C1NACatalogue150Presale / ExternalCGNANACatalogue Guide150Presale / ExternalCLNANACollection550Presale / ExternalCOA5, A6, A9D5Company Confidential InformationNANANA / ConfidentialCPE-onlyE-only, D5Competitive Information550NA / ConfidentialDCE-onlyE-onlyDiscount SchedulesNANAPresale / InternalDIA1, A3NADirect Mail5100Presale / InternalDMNANAProduct Demo550Presale / InternalDSB3D5Dimensions Sheet15Post / ExternalDUB3D5Document Update15Post / ExternalGRB2D6Getting Results15Post / ExternalINB3 Primary, B2D5, D6Installation instructions15Post / ExternalLMNANALaunch Materials550Presale / InternalPCB3D5Packaging ContentsPLE-only primary, B3E-onlyPrice List550Presale / InternalPMB2D6Programming Manual15Post / ExternalPPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / ExternalQRB2 primary, B3, B5D5, D6Quick Reference15Post / ExternalQSB2 primary, B3, B5D5, D6Quick Start15Post / ExternalRMB2D5, D6Reference Manual15Post / ExternalRNB3D5Release Notes15Post / ExternalSGB1 Primary, B4D5, D6Selection Guide Colour550Presale / ExternalSGB2D5, D6Selection Guide B/W550Presale / ExternalSPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / InternalSRB2, B3D5, D6Specification Rating Sheet5100Presale / ExternalTDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / ExternalTGB2, B3D6Troubleshooting Guide15Post / ExternalUMB2 Primary, B4D6User Manual B/W15Post / ExternalWDB3D5Wiring Diagrams / Dwgs15Post / InternalWPB3 Primary, B5D5White Paper550Presale / External** Minimum order quantities on all JIT items are based on the publication length. **Publication lengthMinimum Order Quantity77 or more pages1 (no shrink wrap required)33 to 76 pages253 to 32 pages501 or 2 pages100Pre-sale / MarketingAll paper in this category is White Brightness, 90% or better. Opacity 90% or betterCategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper RequirementsA14 color170 gsm 2pp100# gloss cover, 100# gloss textA24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss textA34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss textA42 color170gsm Silk 120gsm Silk80# gloss cover, 80# gloss textA52 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet textA61 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet textA74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet textA84 color coverCategory being deleted50# matte sheet text, self cover2 color textSelection GuideA92 color100gsm bond50# matte sheet text, self coverSelection GuideGray shading indicates Obsolete Print CatagoriesPost Sale / Technical CommunicationCategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper RequirementsB14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S2 color text50# matte sheet textB21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet textB31 color100gsm bond50# matte sheet text, self coverB42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet textB52 color100gsm bond50# matte sheet text, self coverCatalogsCategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper RequirementsC14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S4 color text45# Coated SheetC24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S2 color text32#-33# Coated SheetJIT / PODAll paper in this category is White Brightness, 82% or better. Opacity 88% or betterCategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper RequirementsD14 color170gsm white silk80# gloss cover, coated 2 sidesD24 color120gsm white silk80# gloss text, coated 2 sides, self coverD34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sidesD41 color160gsm tab90# indexD51 color80gsm bond20# bond, self coverD61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bondD72 color160gsm tab90# indexD82 color80gsm bond20# bond, self coverD92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bondD10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bondGray shading indicates Obsolete Print CatagoriesJust In Time (JIT) or Off Set (OS)?Use these guidelines to determine if your publication should be JIT (just in time/print on demand) or if it would be more economical to print OS (offset/on a press). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the Either category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the JIT category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.Black & White PrintingColor PrintingColor PrintingPrint Spec SheetJIT Printing SpecificationsRA-QR005J-EN-P - 6/14/2013Printing SpecificationYOUR DATA HEREInstructionsNO(required) Publication Number:1756-IN019D-EN-PSample: 2030-SP001B-EN-P11 x 17LOOSE -Loose LeafYESPre-sale / MarketingTOPUse Legacy Number:YES or NO8.5 x 11PERFECT - Perfect BoundA1LEFTLegacy Number if applicable:Sample Legacy Number: 0160-5.338.375 x 10.875SADDLE - Saddle StitchA2RIGHTCORNERPublication Title:ControLogix EtherNet/IP Bridge Module Installation InstructionsSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title8.25 x 11 (RA product profile std)PLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDEUsed in Manufacturing:YESYES or NO - If Yes, must have Part No. listed below8.25 x 10.875STAPLED1 -1 positionA3Part Number:PN-468269If SAP Part Number, be sure to enter PN- before the number7.385 x 9 (RSI Std)STAPLED1B - bottom 1 positionA5(required) CategoryD5Select Print Category A,B,C or D from category list, on "Introduction_Category Types" tab6 x 4STAPLED2 - 2 positionsA6Paper Stock Color:whiteWhite is assumed. For color options contact your vendor5.5 x 8.5 (half-size)THERMAL - Thermal bound (Tape bound)A7Ink Color:blackOne color assumes BLACK / 4 color assume CMYK / Indicate PMS number here4.75 x 7.75THERMALO - Thermal Bound (Tape bound - offline)A8(required) Page Count ofPublication:6Total page count including cover. Enter PAGE count, not SHEET count4.75 x 7 (slightly smaller half-size)A9(required) Finished Trim Size Width:8.5 x 11This is sheet size, before folding4.25" x 5.50"Post Sale / Technical CommunicationFold:Microfold or French Fold - designate no. of folds in Comments - intended for single sheet only to be put in box for manufacturingReview key below. Leave blank if folded for saddle stitching4 x 6B1Finished Fold Size:4.25" x 5.50"This is size after folding is completed3 x 5B2Binding/Stitching:STAPLED1 -1 positionReview key below9 x 12 (Folder)B3NoneStitching Location:CORNERBlank, Corner or SideA4 (8 x 11 ) (210 x 297 mm)B4Half or V or Single FoldDrill Hole (Yes/No):NOAll drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of inch from the inner page border.A5 (5.83 x 8.26) (148 x 210 mm)B5C or Tri-FoldNumber of Tabs Needed:5 tab in stock at RR Donnelley36 x 24 PosterCatalogsDbleParllNumber of Pages per Pad:Average sheets of paper. 25, 50 75,100 Max24 x 36 PosterC1SampleGlue Location on Pad:Glue location on pads18 x 24 PosterC2Short (must specify dimensions between folds in Comments)(required) Business Group:Marketing CommercialAs entered in DocManJIT/PODZ or Accordian Fold(required) Cost Center:19134 - IAIf your Business Unit is Marketing Commercial, add the appropriate division name after 19134 using the chart on the right. All other Business Units: Enter only the number as in DocMan, no description. Example - 1902119134 - Commerc 19134 - OEM 19134 - Compone 19134 - Power C19134 - Global 19134 - Process 19134 - IA 19134 - Service 19134 - IMC 19134 - Safety 19134 - Industr 19134 - Softwar19134 - Mkt Dig 19134 - US MarkeD1Microfold or French Fold - designate no. of folds in Comments - intended for single sheet only to be put in box for manufacturingComments:Fold in quarters (2 folds) so that part number is visible on top.D2Double GateFoldsHalf, V, Single C or TriDble ParllZ or Accordian Microfold or FrenchDouble Gate Short FoldSaddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch -no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words Plastcoil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)D3D4D5D6D7D8D9MBD000B0209.binMBD000B020B.binMBD000B020C.binMBD000B020A.binMBD000B0205.binMBD000B0207.binMBD000B0208.binMBD000B0206.binMBD000B0203.binMBD000B0204.bin
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False /CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

controllogix ethernet/ip bridge...

Documents