ch430-01-02_ima_s223.651.en-02

8/12/2019 CH430-01-02_IMA_S223.651.en-02

1/33

IMA Appendix A Doc. no. S 223.651.en

SANDVIK CH430:01, :02

8/12/2019 CH430-01-02_IMA_S223.651.en-02

2/33

This document is valid for:

Serial no. / Machine no. Sign.

SANDVIK CH430:01, :02

Copyright 2008 Sandvik SRP AB.

All rights reserved. No parts of this document may be reproduced or copied in any form or by

any means without written permission from Sandvik SRP AB. All data and information in this

manual may be changed without further notice. Reservations for misprints.

Document number: S 223.651.en

Original instructions

Issue: 20110511Version: 02

Sandvik

Stationsplan, SE-233 81 Svedala, SwedenTel: +46 (0)40 409000, Fax: +46 (0)40 409260

www.sandvik.com

8/12/2019 CH430-01-02_IMA_S223.651.en-02

3/33

A-3

IM Sandvik CH430:01, :02

Appendix A:

Installation drawings

8/12/2019 CH430-01-02_IMA_S223.651.en-02

4/33

A-4 2008 Sandvik SRP AB

S 223.651.en-01


A.1 General

The following drawings show machine dimensions, connection positions and

dimensions, and access dimensions. All dimensions must be respected.

Dimensions are given in millimeters with inch dimension in brackets.

A.1.1 Mechanical drawings

A.1.2 Electrical drawings

NOTE! The motor can be installed on either side of the crusher.

Drawing name Drawing No. Note

Installation 442.7992

Oil tank installation 442.8326

Oil connection (standard) 442.9820

Oil connection (USA) 442.9819

Air over-pressure (blower/compressed air) 442.8642

Foundation loads 442.9912

Drawing name Drawing No. Note

Piping and instrument diagram, typical installation 194.0434

Connection diagram, oil tank 194.0440

Circuit diagram 194.0441

Instrument list 195.0620

Sensor list 195.0621

Modification of return oil flow switch 194.0190 option

Connection of extra heating elements 194.0191 option

Connection of heating cable 190.3592 option

Connection of heater for Hydroset oil 190.3590 option

8/12/2019 CH430-01-02_IMA_S223.651.en-02

5/33


A-5

2008 Sandvik SRP AB S 223.651.en-01

A.1.3 Foundation loadsDrawing No. 442.9912

The values are applicable for the maximum eccentric throw (36 mm (1.42")).

Forces on foundation at each attachment point.

CH430:01, :02 fixed installation kN lbf

Vertical static load including material* 31 6970

Dynamic load during normal operation f = 6.0 Hz:

Rotating horizontal force (H) 10 2250

Cyclic vertical force (V) 15 3375

* Material volume =1.20 m3(40 ft3)

* Bulk density = 1 800 kg/m3(3 970 lbs)

CH430:01, :02 on rubber dampers kN lbf


Dynamic load during starting and stopping:



Dynamic load during normal operation f = 6.0Hz



* Material volume = 1.20 m3 (40 ft3)

* Bulk density = 1 800 kg/m3 (3970 lbs)

Horizontal displacement: 15 mm in all directions during starting and stopping 5 mm in all directions during operation

CH430:01, :02 with subframe on rubber dampers kN lbf


Dynamic load during starting and stopping:



Dynamic load during normal operation f = 6.0 Hz



* Material volume = 1.20 m3 (40 ft3)

* Bulk density = 1 800 kg/m3 (3970 lbs)

Horizontal displacement: 15 mm in all directions during starting and stopping 5 mm in all directions during operation

8/12/2019 CH430-01-02_IMA_S223.651.en-02

6/33


S 223.651.en-01


A.1.4 Mechanical connections

Drawing No. 442.9820 (standard)

Drawing No. 442.9819 (USA)

The drawings show the points on the crusher and tank unit where

connections are made, and also show the hoses that are supplied.

This overview shows general information about the connections for the cone

crusher and its accessories.

Tank unit Dimension Max pressure

A Lubrication oil from crusher Rp 2" internal thread

B Lubrication oil to crusher Rp 1" internal thread

C Hydroset Rp " internal thread

D To oil heat exchanger Rp 1"

E From oil heat exchanger Rp 1"

F, G Over-pressure air Rp " internal thread

Crusher

H Over-pressure air Rp " internal thread

I Lubrication oil to tank R 2"

K Lubrication oil from tank G 1" B

L Hydroset G " B

Water/oil heat exchanger (option)

M Oil inlet G 1" B

N Water outlet G 1" B

O Water inlet Rp 1" B

P Oil outlet G 1" B

Air/oil heat exchanger

Q Oil outlet G 1"

R Oil inlet G 1"

8/12/2019 CH430-01-02_IMA_S223.651.en-02

7/33


A-7

2008 Sandvik SRP AB S 223.651.en-01

Mechanical connections overview

GH

I

K

L

A

F

B

C

M N

O P

R

Q

E

D

8/12/2019 CH430-01-02_IMA_S223.651.en-02

8/33


S 223.651.en-01


A.1.5 Cable overview

This cable overview shows general information about electrical cables not

included in the delivery from Sandvik.

Site specific signal cables are excluded from this table.

NOTE! All cable types and dimensions must meet local legislation.

Cabledesignation

Object Cable path Rating Notes

From To 50 Hz 60 Hz

W1-M1 Crusher main motor Switchgear -M1 75132 kW

W1-M2 Lubrication oil pump Switchgear -L9 1.5 kW 1.7 kW

W1-M3 Cooling fan Switchgear -M3 1.5 kW 1.7 kW Option

W1-M8 Over-pressure fan Switchgear -M8 0.37 kW 0.43 kW Option

W1-E7 Oil tank heating Switchgear -L9 2.58.2 kWdepending on voltage andnumber of heaters

W1-CV Power supply Switchgear -L9 - -

W2-CV Signals from switches -L9 Control systemor similar

- -

8/12/2019 CH430-01-02_IMA_S223.651.en-02

9/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

10/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

11/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

12/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

13/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

14/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

15/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

16/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

17/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

18/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

19/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

20/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

21/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

22/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

23/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

24/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

25/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

26/33

INSTRUMENT LIST

Plant:

Equipment Tag No:

Equipment Name: HYDROCONE CH/CS-420/430

Equipment Supplier: SANDVIK ROCK PROCESSING

IDENTIFICATION INSTRUMENT TYPE APPLICATION INSTRUMENT DETAILS

Plant SRP Model Range Part No.Tag No. Tag No.

-TI1 Thermometer Return oil temperature (main) ICF 60 0-120C 923.0192-00

-PI1 Pressure gauge Hydroset pressure 100M20-2 0-6 MPa 923.0379-00

-PI2 Pressure gauge Oil pressure (main) 2748 D63 0-1.6 MPa 923.0193-00

-LI1 Oil level indicator Oil level in tank (main) H00361-010 High/Low 914.0174-00

-LI2 Oil level indicator Oil level in tank (Hydroset) H00361-007 High/Low 914.0170-00

Sandvik Rock Processing

Rev: 01/New branding

Date: 07-06-15/Jwa

195.0620 Instrument list CH_CS-420_430 Typical installation

1 (1)

8/12/2019 CH430-01-02_IMA_S223.651.en-02

27/33

SENSOR LIST

Plant:

Equipment Tag No:

Equipment Name:

Equipment Supplier:

SENSOR TYPE APPLICATION

Plant SRP Model Range Part No. OTag No. Tag No.

-TG1 Thermostat Return oil temperature RT101 17-5003 923.0095-00 NC

-TG2 Thermostat Oil cooling RT101 17-5003 923.0095-00 NC

-TG3 Thermostat Oil heating RT101 17-5003 923.0095-00 NC

-OG1 Flow indicator Return oil flow HeliFloat PF 984.1008-00 NC

-PG2 Pressure guard Filter diff. pressure (main) PIS3097 2.2 bar 912.0127-00 NO

-B1N Position sensor Mainshaft position (HS-2800) EDS 160 0-160mm 984.0390-00 4-2

-B1N Position sensor Mainshaft position (HS-3800) EDS 250 0-250mm 984.0391-00 4-2

-B2N Press. transmitter Hydroset pressure 3376 0-250bar 923.0507-00 4-2

-B3N Temp. transmitter Return oil temperature FLEXTOP PT-100 0-200C 923.0489-00 4-2

-U1N Power transducer Drive motor power draw P200-054 4-2

SENSOR DETAILS

HYDROCONE CH/CS-420/430

SANDVIK ROCK PROCESSING

IDENTIFICATION

Sandvik Rock Processing

Rev: 01/ New branding

Date: 07-06-05/Jwa

195.0621 Sensor list CH_CS-420_430 Typical installation

1 (1)

8/12/2019 CH430-01-02_IMA_S223.651.en-02

28/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

29/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

30/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

31/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

32/33

8/12/2019 CH430-01-02_IMA_S223.651.en-02

33/33

ch430-01-02_ima_s223.651.en-02

Documents