bionic fish · 2019-02-07 · your bionic fish is ready. continue with the next steps in the...
TRANSCRIPT
Bionic Fish
Assembly Instructions
Festo AG & Co. KG Festo Didactic SE
2
Equipment and Supplies
Required items from the Bionics Kit and/or Materials Pack:
1. Tail fin (large) assembled and attached to the plastic component (with cutouts) – see ‘Start Here’ for tail fin assembly instructions 2. Tail fin (small) assembled – 2 3. Transparent corpus (body) 4. Small, waterproof servo motor (marked with a sticker) 5. Connecting element 6. Cable ties 7. Sealing rings – 2 8. Tube (clear) 9. Electronic board with microcontroller 10. Material for fish tail and body (plastic poster board)
1 2 3
8
4
7 9
6 5
10
Festo AG & Co. KG Festo Didactic SE
3
Equipment and Supplies, continued
Additionally required:
1. Water basin 2. 4-AA batteries 3. Scissors 4. Items to balance the fish (nuts, bolts, coins, etc.) 5. Phillips head screwdriver
1
2 3 4
5
Festo AG & Co. KG Festo Didactic SE
4
If the tail fins have been previously assembled, please go directly to the Instructions on the next page.
Tail Fin Assembly
From the Bionics Kit, locate the bag containing the tools and 2 screws (used in Step 3). Next, locate the bags containing the small screws and nuts (long and short) and the plastic support pieces (large and small). To assemble the large tail fin, attach the large support pieces to the inside of the fin using the longer screws, nuts, and tools.
Locate the plastic component (with cutouts). Place the opening on the base of the assembled large tail fin over the post on the plastic component. Align the screw holes and connect the pieces together using the 2 screws and a screwdriver.
Assemble the small fins using the small support pieces, the shorter screws, nuts, and tools.
Start Here
1
2
4
3
Festo AG & Co. KG Festo Didactic SE
5
Instructions
Required items: 2 sealing rings, connecting element Place the two sealing rings on each end of the connecting element.
Required items: assembled tail fin (large) Attach the large tail fin to one side of the connecting element. Twist to lock it in place.
1
2
Festo AG & Co. KG Festo Didactic SE
6
Required items: clear tube Attach the clear tube to the opening of the large tail fin. The top of the clear tube should be at approximately the same level as the third support piece from the bottom of the fin. If needed, cut the tube with scissors to the appropriate length.
Required items: small, waterproof servo motor Attach the waterproof servo motor to the holder on the large tail fin, such that the rudder horn of the motor points downwards. Guide the cable of the servo motor through the clear tube.
3
4
Festo AG & Co. KG Festo Didactic SE
7
Required items: 1 cable tie While holding the clear tube against the servo motor, connect it to the large tail fin with a cable tie. Shorten the cable tie, if necessary.
5
Festo AG & Co. KG Festo Didactic SE
8
Required items: 4 cable ties Connect the large tail fin to the rudder horns of the servo motor using 2 cable ties. Pull the cable ties through the two small tabs of the fin and then through the openings of the rudder horn in a crisscross fashion. The two cable ties cross above the fin. Add 2 more cable ties to act as stopper.
Testing Carefully move the rudder horn back and forth with your finger to check the tension of the cable ties. If the fin does not move evenly, the length or the tension of the cable ties may have to be corrected.
6
7
Shorten the cable ties, if necessary.
Festo AG & Co. KG Festo Didactic SE
9
Required items: electronic board with microcontroller, 4 AA batteries Insert the batteries, 2 on each side of the electronic board with microcontroller.
Required items: electronic board with microcontroller, small waterproof servo motor Insert the plug of the servo motor into one of the electronics board’s set of pins.
8
9
Festo AG & Co. KG Festo Didactic SE
10
Required items: transparent corpus (body) Insert the electronics board with microcontroller into the transparent corpus (body) and slide it into the rail located inside. Turn the switch “on”. The small light on the electronics board turns on.
Required items: tail fin (large) Attach the connecting element onto the transparent corpus (body). Twist to lock it into place.
10
11
Festo AG & Co. KG Festo Didactic SE
11
Required items: 2 tail fins (small), 1 cable tie Attach the two small tail fins around the transparent corpus (body) using a long cable tie. Pass the cable tie through the openings located on the tail fins and also on the corpus (body).
The two small tail fins serve as lateral fins. Shorten the cable tie, if necessary
12
Festo AG & Co. KG Festo Didactic SE
12
Required items: material for fin Review some of the basic tail fins shapes found in the Biological Background section on the bionics4education website. Draw your desired fin shape on the material and cut it out. Then make two small holes in the fin so that it can be attached to the large tail fin.
13
Festo AG & Co. KG Festo Didactic SE
13
Required items: 1 cable tie Attach your fin to the small end of the tail fin (large) using a cable tie. Shorten the cable tie, if necessary.
Optional: make a body for your bionic fish Would you like to add a body to your robotic fish? Simply print the body template available in the Downloads section on the bionics4education website and then - trace it, cut it, and attach it!
14
15
Festo AG & Co. KG Festo Didactic SE
14
Congratulations! Your Bionic Fish is ready. Continue with the next steps in the Getting Started section on the bionics4education website to learn how to adjust your fish’s weight and control your bionic fish.