BHEL PAPER - 11 FEB 2007 - NEW DELHI

1. The ratio of two specific heats of air is equal to. = 1.41

2. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

3. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)

6. The unit of entropy is = J/kg 0K

7. Indicated power of a 4-stroke engine is equal to = pLAN/2

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)

9. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)

10. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine

12. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

13. Air fuel ratio in a jet engine is = 60:1

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)

16. Which refrigerants has the highest critical point temperature. = Freon-11

17. Wet bulb temperature is. = indication of amount of moisture in air

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. Surface tension has the units. = newtons/m

20. The line of action of the buoyant force acts through the. = centroid of the displaced volume of fluid

21. A pressure of 25m of head of water is equal to. =245kN/m2

22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.

23. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH

24. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6

25. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.

26. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m

27. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.

28. 10m of water column is equal to = 100kN/m2

29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2

30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450

31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.

32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21

33. A car is moving with a velocity of 60km/hr and possesses energy of 5x105 joules. The mass of the car will be. =3000kg.

34. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR

35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8.

36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2

37. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B

38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.

40. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

41. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.

42. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.

44. Brittle coating technique is used for: = experimental stress analysis.

45. Factor of safety is the ratio of: = yield stress/working stress.

46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.

47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel

48. The product of Cupola is called: = cast iron

49. Brinell tester uses a hardness steel ball of size: = 10mm

50. Sintered and tungsten carbides can be machined by: = EDM

51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.

52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.

53. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.

54. PERT is: = event oriented technique

55. Bar charts are suitable for: = minor works.

56. ? on a PERT/CPM chart represents: = a significant event representing some mile-stone

57. Electron volt is the unit of : = Energy.

58. Seamless tubes are made by?

59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.

60. Why DC current is not used in transformer?

61. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.

62. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

63. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?

BHEL TRICHY

They conducted for four brances in Engineering: Comp sci, ECE, EEE and Mech. In Mechanical stream there were a total of 240 questions.

120- Technical questions in Mechanical Engineering120- General Apptitude questions. (Quantitative Aptitude, Reasoning Ability, Logical thinking, English usage)

The questions were mainly asked inThermodynamicsEngineering MechanicsTheory of machinesProduction techIf you have strong fundas, u can really do well in this session...

Following are the questions asked: (I will try to give you as many questions as i remember)[One Mark for correct answer, 1/5th for wrong answer. Five choices were given]

1)Unit of Entropy (J/kg K or kJ/kg K)

2)A mass of 100kg is falling from a height of 1 m and penetrates the sand into for 1 m. What is the resistance force given by sand.

3)Ratio of specific heats of air. (1.41)

4)A body weighs 3 kg in air. If it is submerged in a liquid, it weighs 2.5 kg. What is the specific gravity of the liquid.

5)Two cars travell in same direction at 40 km/hr at a regular distance. A car comes in a opposite direction in 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between them?

6)A simple problem involing in hoops stress. For sphere: M= [3/2]*p*V*[density of pressure vessel material/Maximum working stress it can tolerate] For Thin walled pressure walls: Hoops stress or stress in the radial direction =p*r/2t

7)A problem in force calculation in a body moving in a inclined surface.

8)Composition of bronze. (Copper+zinc)

9)Compostion of stainless steel.(iron+chromium+nickel+carbon)

10)CI is manifactured in which process. (cupola process)

11)What percentage of carbon is preset in pig iron. (4.5 to 6%)

12)Water is available at 10m height. What is the pressure available? (pressure=density*g*height; p=1000*9.81*10; p=98100N/m2)

13)What will happen if the speed of the centrifugal pump doubles.

14)The unit eV is widely used in ? (Nuclear and atomic physics)

15)What will happen to the resistance, when the diameter of the conductor is doubled?

16)The power comsumed by a electrical device is 1000W at 250V, What is the resistance in the device?(Power= Voltage*current; Current=Power/Voltage, Current,I=1000/250=4amps. V=IR, Therefore R=250/4=62.5 ohms)

17)Why DC current is not used in transformer.

18)On what principle the sonar/ radar works?

19)Bending moment diagram for the UDL is in what shape?

20)Function of the distributor in petrol vehicles? (Spark timing)

21)Which is not present in CI engines? (carburrettor)

22)What will happen if one cylinder recieves more amount of fuel spray from injectors than other injectors?

23)Purpose of draft tube in hydraulic turbines? (The purpose of a draft tube is toconvert some of the kinetic energy of the flow from the runner (the rotating part of the turbine) intopressure energy and thereby increase the efficiency ofthe hydro power turbine.)

24)What is the effect or reheater in the gas turbine? (The advantage of reheater is significantly increased thrust; the disadvantage is it has very high fuel consumption and inefficiency)

25)Problems involving with fricition coefficient.

26)Factor of safety = Yeild stress/Working stress.

27)Which is the example of non parallel power transmission (Universal coupling)

28)For perpendicular shafts worm gear is used.

29)A planet gear with 25 teeth is meshed with a sun gear of 100 teeth. Both are connected using a arm. How many rotations are needed for planet gear to complete one rotation around the sun gear?

30)What is equivalent spring constant for spring in parallel?

31) Some questions was asked related to boundry layer and vortex flow.

32) 5 questions were asked in PERT, Process planning, Product planning, Break even analysis.

33)How are tungsten and sintered composite materials are machined? (Electro Discharge Machining, EDM)

General Apptitude:All the sections were very easy. Basic knowledge is sufficient to attend all the questions. But Keep time factor in mind and increase your speed. There are 120 questions like this!!

English:--- Detect the words with wrong spellings (5 questions)--- Fill in the blanks with appropriate words(5 questions)--- Two reading comprehensions were given(10 questions)--- Find the error in the sentence (8 questions)

Reasoning:--- Seating arrangement problems--- Find the relation between them

Quantitative ability:All the questions were very easy.--- 50% of the questions are from basic geometry.--- Remaining were very general and easy. But as there is a total 120 questions you have to be really quick.

BHEL PROFILE

Established in the late 50s, Bharat Heavy Electricals Limited ( BHEL ) is, today, a name to reckon with in the industrial world.It is the largest engineering and manufacturing enterprise of its kind in India, and one of the leading international companies in the power field. BHEL offers over 180 products and provides systems and services to meet the needs of core sectors like:Power,Transmission, Industry, Transportation,Non-Conventional Energy Sources,Oil & Gas Exploration & Telecommunication . With 14 Manufacturing Divisions,a wide spread Regional Services Network , and Project Sites all over India & abroad and with an export presence in more than 50 countries, BHEL is truly Indias Industrial ambassador to the world. All major Manufacturing,Erection and Service units of BHEL have been awarded ISO 9000 certification.

BHELs plant is the companys oldest unit with updated & state-of-the-art manufacturing facilities. The product range at includes Hydro, Steam, Marine & Nuclear Turbines, Hydro & Turbo Generators, Transformers, Switchgears, Controlgears, Transportation Equipments,Capacitors,Bushings, Electrical Motors, Rectifiers,Oil Drilling Rig Equipments, Battery Powered Vehicles and Diesel Generating sets. This unit have been recommended for ISO-14001 certificate for its Environment Management System.

BHEL Bhopal's strength is it's employees. Company invests in Human Resources continuously and is alive to their needs. The plant's well established Township is spread over an area of around 20 sq kms and provides good Health facilities, Sports & Recreational Parks.

Company : BHEL

1. With reference to your application for the post of Probationary Engineer in our Company, you are required to appear for a written test on Sunday, the 4th July 2004 at 10.00 AM (Reporting Time: 9.30 AM ) at the test centre mentioned below:

560029

2. Please note the following: 2.1. Request for the change of venue will not be considered under any circumstances. 2.2. The written test shall be of objective type for 2 Hours 30 minutes and will consist of objective type questions in your discipline and General Aptitude. 2.3. HB pencils/ Ball point pen (Black) should be used for answering the test. 2.4. Late entrants beyond 30 min from the commencement of the test will not be permitted to take the test. 2.5. Cell phones, Gadgets, Calculators will not be allowed inside the test centre Candidates will have to make their own arrangements for safe custody of their belongings. 2.6. This Admission Ticket along with duly signed photograph affixed on it is to be produced at the test centre without which you will not be permitted to take the test. 2.7. Admission ticket will be collected at the examination hall. Candidates may take photo copy of the admission ticket prior to coming to test centre.

3. Out station SC/ST/PHP candidates appearing for written test will be reimbursed second class to and fro train fare by the shortest route from the railway station nearest to their correspondence address to the place of test centre, subject to the production of : 3.1. Railway ticket/ Receipt,

3.2. Attested copy of Degree or Relevant Marks Card (5th & 6th semesters / 3rd year in case of those who have appeared for final semester/Year), 3.3. Caste/Tribe / Disability Certificate, as applicable, 3.4. Those already completed the course should produce mark sheet of last year / last 2 semesters. Those having more than 55% (SC/ST) and 60% in case of General-PHP & OBC-PHP only will be allowed. Without which no reimbursement shall be made. It may also be noted that if the actual discipline/degree of the candidate is found to be different from those advertised for, he/she will not be eligible for reimbursement. Therefore all SC/ST/PHP candidates are advised not to appear for the test if the disciplines/degree certificate does not tally with disciplines/degree advertised for. The to and fro fare thus paid shall be full and final. Clarification in this regard will not be entertained in the test centre.

4. Candidates short-listed for the interview will be intimated by e-mail/letter.

5. If at any stage the information furnished by you is found incorrect, you will be disqualified from attending the test. The decision of the centre supervisor regarding admission of a candidate for the test is final.

BHEL 2006 Placement paper

Consider the following expressions indicating the step or impulse response of an initially relaxed control system-1. (5 4e-2+) u(t)2. (e-2t +5) (u(t))3 .V(t) + 8e-2t u(t)4 . V(t) + 4e-2t 4(t)

Those which correspond to the step and impulse response of the same system include-1&3

Which is the following relate to rational transfer function of a system-1. Ratio of Fourier transform of output to input with zero initial conditions.2. Ratio of transform of output to input with zero initial conditions.3. transform of system impulse response.

4. transform of system unit step response select the correct answer using the codes given below.Codesa.) 1 and 4b.) 2 and 3c.) 1 and 3d.) 2 and 4For the signal g (t) 10 cos (50 pt) cos2 (150at)

The Nyquist sampling state in t seconds isa.) 150 samples per secondb.) 200 samples per secondc.) 300 samples per secondd.) 350 samples per second

In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must lie between MHz.a.) 34 and 106b.) 52. And 88 c.) 106 and 142d.) 34 and 142

Radar used to eliminate clutter in navigational application is a.) Pulse radarb.) Tracking radarc.) MTI radard.) Mono pulse radar

The 1.55 mm windows is not yet in use with fiber optic systems because a.) The attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mmc.) Suitable laser devices have not yet been developedd.) It does not lend itself to wavelength multiplexing

Pre-emphasis in FM systems involves-a.) Compression of the modulating signalb.) Expansion of the modulating signal c.) Amplification of lower frequency components of the modulating signal. d.) Amplification of higher frequency components of the modulating signal.

In a terrestrial microwave system transmission of signals is achieved through-a.) reflection from the ionosphereb.) line of sight mode c) reflection from the ground d.) diffraction from the stratosphere.

Casse grain feed is used with a parabolic reflector toa.) increase the gain of the systemb). increase the bandwidth of the system c.) reduce the size of the main reflector d.) allow the feed to be placed at a convenient point.

In most microwave communication link rain drop attenuation is caused due to-a.) scattering of microwaves by water drops of specific size.b) scattering of microwaves by a collection of droplets acing as a single body.c.) absorption of microwaves by water and consequent heating of the liquidd.) absorption of the microwaves by water vapor in the atmosphere.

When a (75 j40)W load is connected to a coaxial line of Z0 = 75 W at 6MHz then the load matching on the line can be accomplished by connecting-a.) A short circuited stub at the loadb.)An inductance at the loadc. )A short circuited stub at a specific distance from the loadd.)none of the aboveAs compared to analog multimeters, digital multimeters are a.) less accurateb.) more accuratec.) equally accurated.) none.

When a signal of 10 mV at 75 MHz is to be measured then which of the following instruments can be used a.) VTVMb.) Cathode ray oscilloscopec.) Moving iron voltmeterd.) Digital multimeter

Amplifier of class B has high theoretical efficiency of 78.5 percent because-a.) It is biased almost to saturationb.)Its quiescent current is lowc.)Its output is an exact replica of its inputd.)It is biased well below cut off

The coupling that produces minimum interference with frequency response is-a.) Direct couplingb.)Impedance couplingc.) R C couplingd.)Transformer coupling

A superconductor is a a.) A material showing perfect conductivity and Meissner effect below a critical temperatureb.) A conductor having zero resistancec.) A perfect conductor with highest di-magnetic susceptibilityd.) A perfect conductor which becomes resistance when the current density through it exceeds a critical value

When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF capacitor then the self capacitance of the inductor would be a) 8.05 pFb) 10.05pFc.) 16.01pFd.) 20.01pF

The Q of a radio coil a.) is independent of frequencyb.) increases monotonically as frequency increasesc.) decreases monotonically as frequency increasesd.) increases upto a certain frequency and then decreases beyond that frequency

When a generator of internal impedance and operating at 1GHz feeds a load via a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed line is a.) 0.5b.) 1.5c.) 2.5d.) 1.75

The coding system typically used in digital telemetry is a.) PPM (pulse position modulation)b.) PAM (pulse amplitude modulation)c.) PCM (pulse code modulation)d.) PDM (pulse duration modulation)

Radiation pyrometers are used for the measurement of temperature in the range of a.) -2000C to 5000Cb.) 00C to 5000Cc.) 5000C to 12000Cd.) 12000C to 25000C

RF amplifier of an A.M. receiver is normally biased in a.) Class 'A'b.) Class 'b'c.) Class 'C'd.) None

The value of gate voltage for the operation of enhancement of only N channel MOSFET has to be a.) High positiveb.) High negativec.) Low positived.) Zero

BHEL 2006 PLACEMENT PAPER

control system- 1. (5 4e-2+) u(t) 2. (e-2t +5) (u(t)) 3 .V(t) + 8e-2t u(t) 4 . V(t) + 4e-2t 4(t)

Those which correspond to the step and impulse response of the same system include- 1&3

Which is the following relate to rational transfer function of a system- 1. Ratio of Fourier transform of output to input with zero initial conditions. 2. Ratio of Laplace transform of output to input with zero initial conditions. 3. Laplace transform of system impulse response.

4. Laplace transform of system unit step response select the correct answer using the codes given below. Codes a.) 1 and 4 b.) 2 and 3 c.) 1 and 3 d.) 2 and 4 For the signal g (t) 10 cos (50 pt) cos2 (150at)

The Nyquist sampling state in t seconds is a.) 150 samples per second b.) 200 samples per second c.) 300 samples per second d.) 350 samples per second

In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must lie between MHz. a.) 34 and 106 b.) 52. And 88 c.) 106 and 142 d.) 34 and 142

Radar used to eliminate clutter in navigational application is a.) Pulse radar b.) Tracking radar c.) MTI radar d.) Mono pulse radar

The 1.55 mm windows is not yet in use with fiber optic systems because a.) The attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mm c.) Suitable laser devices have not yet been developed d.) It does not lend itself to wavelength multiplexing

Pre-emphasis in FM systems involves- a.) Compression of the modulating signal b.) Expansion of the modulating signal c.) Amplification of lower frequency components of the modulating signal. d.) Amplification of higher frequency components of the modulating signal.

In a terrestrial microwave system transmission of signals is achieved through- a.) reflection from the ionosphere b.) line of sight mode c) reflection from the ground d.) diffraction from the stratosphere.

Casse grain feed is used with a parabolic reflector to a.) increase the gain of the system b). increase the bandwidth of the system c.) reduce the size of the main reflector d.) allow the feed to be placed at a convenient point.

In most microwave communication link rain drop attenuation is caused due to- a.) scattering of microwaves by water drops of specific size. b) scattering of microwaves by a collection of droplets acing as a single body. c.) absorption of microwaves by water and consequent heating of the liquid d.) absorption of the microwaves by water vapor in the atmosphere.

When a (75 j40)W load is connected to a coaxial line of Z0 = 75 W at 6MHz then the load matching on the line can be accomplished by connecting- a.) A short circuited stub at the load b.)An inductance at the load c. )A short circuited stub at a specific distance from the load d.)none of the above As compared to analog multimeters, digital multimeters are a.) less accurate b.) more accurate c.) equally accurate d.) none.

When a signal of 10 mV at 75 MHz is to be measured then which of the following instruments can be used a.) VTVM b.) Cathode ray oscilloscope c.) Moving iron voltmeter d.) Digital multimeter

Amplifier of class B has high theoretical efficiency of 78.5 percent because- a.) It is biased almost to saturation b.)Its quiescent current is low c.)Its output is an exact replica of its input d.)It is biased well below cut off

The coupling that produces minimum interference with frequency response is- a.) Direct coupling b.)Impedance coupling c.) R C coupling d.)Transformer coupling

A superconductor is a a.) A material showing perfect conductivity and Meissner effect below a critical temperature b.) A conductor having zero resistance c.) A perfect conductor with highest di-magnetic susceptibility d.) A perfect conductor which becomes resistance when the current density through it exceeds a critical value

When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF capacitor then the self capacitance of the inductor would be a) 8.05 pF b) 10.05pF c.) 16.01pF d.) 20.01pF

The Q of a radio coil a.) is independent of frequency b.) increases monotonically as frequency increases c.) decreases monotonically as frequency increases d.) increases upto a certain frequency and then decreases beyond that frequency

When a generator of internal impedance and operating at 1GHz feeds a load via a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed line is a.) 0.5 b.) 1.5 c.) 2.5 d.) 1.75

The coding system typically used in digital telemetry is a.) PPM (pulse position modulation) b.) PAM (pulse amplitude modulation) c.) PCM (pulse code modulation) d.) PDM (pulse duration modulation)

Radiation pyrometers are used for the measurement of temperature in the range of a.) -2000C to 5000C b.) 00C to 5000C c.) 5000C to 12000C d.) 12000C to 25000C

RF amplifier of an A.M. receiver is normally biased in a.) Class 'A' b.) Class 'b' c.) Class 'C' d.) None

The value of gate voltage for the operation of enhancement of only N channel MOSFET has to be a.) High positive b.) High negative c.) Low positive d.) Zero

BHEL company Profile

BHEL was founded in 1950s.Bharat Heavy Electricals Limited-BHEL, has today emerged as the largest engineering and manufacturing enterprise of its kind in India and ranks amongst the top ten power generation equipment manufacturers in the world.With a massive network of 14 manufacturing Units located at various important centres all over ,BHEL manufactures almost all critical high technology products required for power sector like Gas Turbines, Steam Turbines, Turbogenerators, Boilers, Pumps and Heat exchangers, Pulverisers and electrical switch gears.

BHEL is one of the largest exporters of engineering products & services from India. BHEL has established its references in around 60 countries of the world, ranging from the United States in the West to New Zealand in the Far East. Its export range include: individual products to complete power stations, turnkey contracts for power plants, EPC contracts, HV/EHV Sub-stations, O&M services for familiar technologies, specialized after-market services like Residual Life Assessment (RLA) studies and retrofitting, refurbishing & overhauling, and supplies to manufacturers & EPC contractors.

BHEL has acquired certifications to Quality Management Systems (ISO 9001), Environmental Management Systems (ISO 14001) and Occupational Health & Safety Management Systems (OHSAS 18001) and is also well on its journey towards Total Quality Management.The company recorded revenues of INR2,160,800 million (approximately $53,674.3 million) in the fiscal year ended March 2007, an increase of 15.3% over 2006. Its net profit was INR281,500 million (approximately $6,992.5 million) in fiscal year 2007, an increase of 16.6% over 2006.

VISIONA World-class Engineering Enterprise Committed to enhancing Stakeholder Value.

MISSIONTo be an Indian Multinational Engineering Enterprise providing Total Business Solutions through Quality Products, Systems and Services in the fields of Energy, Industry, Transportation, Infrastructure and other potential areas.

The greatest strength of BHEL is its highly skilled and committed 43,636 employees. Every employee is given an equal opportunity to develop himself and grow in his career. Continuous training and retraining, career planning, a positive work culture and participative style of management all these have engendered development of a committed and motivated workforce setting new benchmarks in terms of productivity, quality and responsiveness.

HeadquartersDelhi Area, India

IndustryElectrical/Electronic Manufacturing

TypePublic Company

Company Size43636 employees

Turnover: 18739Rupees (In Million)2006-07,21401Rupees (In Million)2007-08

ContactRegistered Office: BHEL House, Siri Fort, New Delhi - 110049, India

For more details please visit www.bhel.comgoogle_ad_section_end

google_ad_section_start

google_ad_section_end

google_ad_section_end

google_ad_section_end