“do not loose time, choose long life!” · » soil profile is undercut » soil is kept to upper...
TRANSCRIPT
-
“Do not loose time, choose Long Life!”
-
» Significantly higher lifetime than traditional standard parts*
» Consistent working depth and equal quality of work
» Improved penetration, lower traction power requirement due to the permanently sharp cut-ting edges
» No need to adjust working width during the wear-out period
» Time and cost savings due to fewer worn parts
» Longer period of use during a season
» Lower costs per hectar.
» Optimal utilisation of tractor power
» Savings on storage space and transport costs
With new Long Life working tips and wings you will achieve quality, time and cost benefits:
BEDNAR is dedicated to the importance of high quality of the wearable parts. The cost of wearable parts plays an important role throughout the entire life of the soil processing machine.
Higher level of resistency of tips and wings significantly lowers not only the cost of wear on parts but also the time required for exchange of working units (tips, wings…). New tips and wings Long Life significantly increase the lifetime of these parts and thus increase the effectivness of the machines use.
*4–7× higher lifetime based on type of the machine, working depth, width, type of soil, moisture, tractor power, ground speed and position of the tips and wings
Long LifeComparative wear-out of the tips
» Minimal wear in length and reduced wear in thickness
» No readjustment of the working depth
» Consistently good penetration in soil profiles
» Constant high quality of work
» Much higher lifetime
» Much higher machine performance due possibility to use machine effectively
LONG LIFE TIPS
Soil test made in very abrasive soil conditions has proven up to 7 times higher lifetime of long life tips in com-parison with standard tips. Give it a try – it’s worth it!
» Wear in length and thickness of tips affect function of the tips
» Working depth of machine must to be readjusted according the wear of the tips
» Worse penetration in soil profiles in case of worn tips
» Insufficient quality of work
STANDARD TIPS
“Do not loose time, choose Long Life!”
-
NEW STANDARD TIPS WORN STANDARD TIPS
STANDARD WINGS LONG LIFE WINGS
LONG LIFE TIPS
» Minimal wear of tips length
» Optimum loosening of tips
» Optimum mixing of tips
» Problem-free work in depth
» Flat bottom
» Optimum drainage
» Constant quality of penetration
» Much higher machine performance due to machine working effectively
» Wear of tip lenght affects function
» Worse loosening of tips
» Worse mixing of tips
» Worse work in depth
» Formation of uneven bottom
» Worse drainage
» Worse penetration of weared tips
STANDARD TIPS
Comparison of work quality
» Flat working angle
» Soil profile is undercut
» Soil is kept to upper layers
» Low traction resistance for the tractor
» Permanently flat working angle
» Soil is undercut
» Soil is kept in upper layers
» Constant low traction resistance
» Reduction of fuel consumption
» Reduction of strain on the machine (frames, bearing etc.)
» Higher working performance
» Acute working angle
» Soil is pushed (soil is not undercut as by new tips)
» Soil is no longer kept in upper layers
» Higher traction resistance
» Higher fuel consumption
» High level of strain on the machine (frames, bearing etc.)
» Reduction of working speed
THE CHARACTERISTICS OF NEW AND WORN LONG LIFE TIPS
STAY CONSTANT!
LONG LIFE TIPS
» Wear in width affects the function of wings
» Loss of functionality
» Worse undercutting of soil profiles
» Worse mixing
» Worse establishment of seedbed
» Worse weed control
» Minimal wear in width of wings
» Maintenance of functionality
» Excellent undercutting of soil profiles
» Excellent mixing
» Optimum seedbed estabilishment
» Effective weed management
» Much higher machine performance due machine working effectively
Comparison of tips / wings characteristics
COMPARISON OF WINGS
-
New wear resistant Long Life tips and wingsfor versatile cultivators FENIX
New wear resistant Long Life tipsfor chisel ploughs TERRALAND
FENIXVersatile cultivators
TERRALANDChisel ploughs
Wear resistant carbides on the tips
Screw holes for attaching the tips to a tine
Screw holes for attaching the tips to a tine
Reinforcement of bottom part of the tips
ORDER CODES:
KM060334 – Tip Long Life 80 mm (1 pc)KM000854 – Screw (1 pc)KM000858 – Screw (1 pc)KM000855 – Nut (2 pcs)
KM060316 – Wing Long Life L 185 mm (1 pc)KM060317 – Wing Long Life R 185 mm (1 pc)KM000890 – Screw (2 pcs)KM000296 – Nut (2 pcs)
ORDER CODES:
KM060340 – Tip Long Life 40 mm (1 pc)KM000906 – Screw (1 pc)KM000854 – Screw (1 pc)KM000855 – Nut (2 pcs)
Wear resistant carbides on the tips
Reinforcement of bottom part of the tips
Wings with carbides
-
www.bednar-machinery.com
The technical data and illustrations are approximate.Reservations are made for any design changes.
BEDNAR FMT s.r.o.Lohenická 607
190 17 Praha 9 - VinořCzech Republic
T: +420 283 092 529E: [email protected]
W: www.bednar-machinery.comProduct range
INTER-ROW CULTIVATION
Inter-row cultivator ROW-MASTER
Rotary cutters MULCHER
Straw harrows STRIEGEL-PRO Disc cultivators SWIFTERDISC Disc cultivators ATLAS
Seedbed cultivators SWIFTER Versatile cultivators FENIX
Trailed packers CUTTERPACK, PRESSPACK, GALAXY
Chisel ploughs TERRALAND
Fertliser hopper FERTI-BOXSeed drills OMEGA
TILLAGE
TILLAGE
TILLAGE
SOWING AND FERTILISING ROTARY CUTTERS