antenna (radio).pdf
TRANSCRIPT
-
8/13/2019 Antenna (radio).pdf
1/23
-
8/13/2019 Antenna (radio).pdf
2/23
Antenna (radio) 2
Terminology
Electronic symbol
for an antenna
The words antenna (plural: antennas[2]
in US English, although both "antennas" and
"antennae" are used in International English[3]
) and aerial are used interchangeably.
Occasionally a rigid metallic structure is called an "antenna" while the wire form is called an
"aerial". However, note the important international technical journal, the IEEE Transactions
on Antennas and Propagation.[4] In the United Kingdom and other areas where British English
is used, the term aerial is sometimes used although 'antenna' has been universal in professional
use for many years.
The origin of the word antenna relative to wireless apparatus is attributed to Italian radio
pioneer Guglielmo Marconi. In 1895, while testing early radio apparatus in the Swiss Alps at
Salvan, Switzerland in the Mont Blanc region, Marconi experimented with long wire "aerials".
He used a 2.5 meter vertical pole, with a wire attached to the top running down to the
transmitter, as a radiating and receiving aerial element. In Italian a tent pole is known as
l'antenna centrale, and the pole with the wire was simply called l'antenna. Until then wireless
radiating transmitting and receiving elements were known simply as aerials or terminals.Because of his prominence, Marconi's use of the word antenna (Italian forpole) spread among
wireless researchers, and later to the general public.[5]
In common usage, the word antenna may refer broadly to an entire assembly including support
structure, enclosure (if any), etc. in addition to the actual functional components. Especially at microwave
frequencies, a receiving antenna may include not only the actual electrical antenna but an integrated preamplifier or
mixer.
Overview
Antennas of the Atacama Large Millimeter
submillimeter Array.
Antennas are required by any radio receiver or transmitter to couple its
electrical connection to the electromagnetic field. Radio waves are
electromagnetic waves which carry signals through the air (or through
space) at the speed of light with almost no transmission loss. Radio
transmitters and receivers are used to convey signals (information) in
systems including broadcast (audio) radio, television, mobile
telephones, wi-fi (WLAN) data networks, trunk lines and
point-to-point communications links (telephone, data networks),
satellite links, many remote controlled devices such as garage door
openers, and wireless remote sensors, among many others. Radio
waves are also used directly for measurements in technologies
including RADAR, GPS, and radio astronomy. In each and every case, the transmitters and receivers involved
require antennas, although these are sometimes hidden (such as the antenna inside an AM radio or inside a laptop
computer equipped with wi-fi).
http://en.wikipedia.org/w/index.php?title=Radio_astronomyhttp://en.wikipedia.org/w/index.php?title=GPShttp://en.wikipedia.org/w/index.php?title=RADARhttp://en.wikipedia.org/w/index.php?title=Garage_door_openerhttp://en.wikipedia.org/w/index.php?title=Garage_door_openerhttp://en.wikipedia.org/w/index.php?title=Remote_controlledhttp://en.wikipedia.org/w/index.php?title=Trunkinghttp://en.wikipedia.org/w/index.php?title=WLANhttp://en.wikipedia.org/w/index.php?title=Wi-fihttp://en.wikipedia.org/w/index.php?title=Mobile_telephoneshttp://en.wikipedia.org/w/index.php?title=Mobile_telephoneshttp://en.wikipedia.org/w/index.php?title=Televisionhttp://en.wikipedia.org/w/index.php?title=Absorption_%28electromagnetic_radiation%29http://en.wikipedia.org/w/index.php?title=Speed_of_lighthttp://en.wikipedia.org/w/index.php?title=Electromagnetic_waveshttp://en.wikipedia.org/w/index.php?title=Radiohttp://en.wikipedia.org/w/index.php?title=File%3AThe_Atacama_Large_Millimeter_submillimeter_Array_%28ALMA%29_by_night_under_the_Magellanic_Clouds.jpghttp://en.wikipedia.org/w/index.php?title=Atacama_Large_Millimeter_Arrayhttp://en.wikipedia.org/w/index.php?title=Atacama_Large_Millimeter_Arrayhttp://en.wikipedia.org/w/index.php?title=Frequency_mixerhttp://en.wikipedia.org/w/index.php?title=Italian_languagehttp://en.wikipedia.org/w/index.php?title=Mont_Blanchttp://en.wikipedia.org/w/index.php?title=Salvan%2C_Switzerlandhttp://en.wikipedia.org/w/index.php?title=Swiss_Alpshttp://en.wikipedia.org/w/index.php?title=Guglielmo_Marconihttp://en.wikipedia.org/w/index.php?title=British_Englishhttp://en.wikipedia.org/w/index.php?title=United_Kingdomhttp://en.wikipedia.org/w/index.php?title=IEEE_Transactions_on_Antennas_and_Propagationhttp://en.wikipedia.org/w/index.php?title=IEEE_Transactions_on_Antennas_and_Propagationhttp://en.wikipedia.org/w/index.php?title=Scientific_journalhttp://en.wikipedia.org/w/index.php?title=File%3AAntennaSymbol.png -
8/13/2019 Antenna (radio).pdf
3/23
Antenna (radio) 3
Whip antenna on car, common example
of an omnidirectional antenna
According to their applications and technology available, antennas generally
fall in one of two categories:
1. Omnidirectional or only weakly directional antennas which receive or
radiate more or less in all directions. These are employed when the relative
position of the other station is unknown or arbitrary. They are also used at
lower frequencies where a directional antenna would be too large, orsimply to cut costs in applications where a directional antenna isn't
required.
2. Directional or beam antennas which are intended to preferentially radiate
or receive in a particular direction or directional pattern.
In common usage "omnidirectional" usually refers to all horizontal directions,
typically with reduced performance in the direction of the sky or the ground
(a truly isotropic radiator is not even possible). A "directional" antenna
usually is intended to maximize its coupling to the electromagnetic field in
the direction of the other station, or sometimes to cover a particular sector
such as a 120 horizontal fan pattern in the case of a panel antenna at a cell site.
One example of omnidirectional antennas is the very common vertical antenna or whip antenna consisting of a metal
rod (often, but not always, a quarter of a wavelength long). A dipole antenna is similar but consists of two such
conductors extending in opposite directions, with a total length that is often, but not always, a half of a wavelength
long. Dipoles are typically oriented horizontally in which case they are weakly directional: signals are reasonably
well radiated toward or received from all directions with the exception of the direction along the conductor itself;
this region is called the antenna blind cone or null.
Half-wave dipole antenna
Both the vertical and dipole antennas are simple in construction and relatively
inexpensive. The dipole antenna, which is the basis for most antenna designs,
is a balanced component, with equal but opposite voltages and currents
applied at its two terminals through a balanced transmission line (or to a
coaxial transmission line through a so-called balun). The vertical antenna, on
the other hand, is a monopole antenna. It is typically connected to the inner
conductor of a coaxial transmission line (or a matching network); the shield
of the transmission line is connected to ground. In this way, the ground (or
any large conductive surface) plays the role of the second conductor of a
dipole, thereby forming a complete circuit. Since monopole antennas rely on a conductive ground, a so-called
grounding structure may be employed to provide a better ground contact to the earth or which itself acts as a ground
plane to perform that function regardless of (or in absence of) an actual contact with the earth.
http://en.wikipedia.org/w/index.php?title=Ground_planehttp://en.wikipedia.org/w/index.php?title=Ground_planehttp://en.wikipedia.org/w/index.php?title=Ground_%28electricity%29http://en.wikipedia.org/w/index.php?title=Circuit_theory%23Open_circuit_vs._closed_circuithttp://en.wikipedia.org/w/index.php?title=Ground_%28electricity%29http://en.wikipedia.org/w/index.php?title=Coaxial_cablehttp://en.wikipedia.org/w/index.php?title=Balunhttp://en.wikipedia.org/w/index.php?title=Balanced_linehttp://en.wikipedia.org/w/index.php?title=Balancedhttp://en.wikipedia.org/w/index.php?title=File%3AHalf_%E2%80%93_Wave_Dipole.jpghttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Whip_antennahttp://en.wikipedia.org/w/index.php?title=Cell_sitehttp://en.wikipedia.org/w/index.php?title=Isotropichttp://en.wikipedia.org/w/index.php?title=Directional_antennahttp://en.wikipedia.org/w/index.php?title=Omnidirectional_antennahttp://en.wikipedia.org/w/index.php?title=File%3ACar_radio_antenna_extended_portrait.jpeghttp://en.wikipedia.org/w/index.php?title=Whip_antenna -
8/13/2019 Antenna (radio).pdf
4/23
Antenna (radio) 4
Diagram of the electric fields (blue) and
magnetic fields (red) radiated by a dipole
antenna (black rods) during transmission.
Antennas more complex than the dipole or vertical designs are usually
intended to increase the directivity and consequently the gain of the antenna.
This can be accomplished in many different ways leading to a plethora of
antenna designs. The vast majority of designs are fed with a balanced line
(unlike a monopole antenna) and are based on the dipole antenna with
additional components (or elements) which increase its directionality.Antenna "gain" in this instance describes the concentration of radiated power
into a particular solid angle of space, as opposed to the spherically uniform
radiation of the ideal radiator. The increased power in the desired direction is
at the expense of that in the undesired directions. Power is conserved, and
there is no net power increase over that delivered from the power source (the
transmitter.)
For instance, a phased array consists of two or more simple antennas which are connected together through an
electrical network. This often involves a number of parallel dipole antennas with a certain spacing. Depending on the
relative phase introduced by the network, the same combination of dipole antennas can operate as a "broadside
array" (directional normal to a line connecting the elements) or as an "end-fire array" (directional along the line
connecting the elements). Antenna arrays may employ any basic (omnidirectional or weakly directional) antenna
type, such as dipole, loop or slot antennas. These elements are often identical.
Rooftop television Yagi-Uda antennas
like these six are widely used at VHF and
UHF frequencies.
However a log-periodic dipole array consists of a number of dipole elements
of different lengths in order to obtain a somewhat directional antenna having
an extremely wide bandwidth: these are frequently used for television
reception in fringe areas. The dipole antennas composing it are all considered
"active elements" since they are all electrically connected together (and to the
transmission line). On the other hand, a superficially similar dipole array, the
Yagi-Uda Antenna (or simply "Yagi"), has only one dipole element with anelectrical connection; the other so-called parasitic elements interact with the
electromagnetic field in order to realize a fairly directional antenna but one
which is limited to a rather narrow bandwidth. The Yagi antenna has similar
looking parasitic dipole elements but which act differently due to their
somewhat different lengths. There may be a number of so-called "directors"
in front of the active element in the direction of propagation, and usually a
single (but possibly more) "reflector" on the opposite side of the active
element.
Greater directionality can be obtained using beam-forming techniques such as
a parabolic reflector or a horn. Since the size of a directional antenna depends on it being large compared to the
wavelength, very directional antennas of this sort are mainly feasible at UHF and microwave frequencies. On the
other hand, at low frequencies (such as AM broadcast) where a practical antenna must be much smaller than a
wavelength, significant directionality isn't even possible. A vertical antenna or loop antenna small compared to the
wavelength is typically used, with the main design challenge being that of impedance matching. With a vertical
antenna a loading coil at the base of the antenna may be employed to cancel the reactive component of impedance;
small loop antennas are tuned with parallel capacitors for this purpose.
An antenna lead-in is the transmission line (orfeed line) which connects the antenna to a transmitter or receiver. The
antenna feed may refer to all components connecting the antenna to the transmitter or receiver, such as an impedance
matching network in addition to the transmission line. In a so-called aperture antenna, such as a horn or parabolicdish, the "feed" may also refer to a basic antenna inside the entire system (normally at the focus of the parabolic dish
http://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Antenna_feedhttp://en.wikipedia.org/w/index.php?title=Feed_linehttp://en.wikipedia.org/w/index.php?title=Transmission_linehttp://en.wikipedia.org/w/index.php?title=Loop_antenna%23Small_loopshttp://en.wikipedia.org/w/index.php?title=Electrical_reactancehttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Loop_antenna%23Small_loopshttp://en.wikipedia.org/w/index.php?title=Parabolic_reflectorhttp://en.wikipedia.org/w/index.php?title=Passive_radiatorhttp://en.wikipedia.org/w/index.php?title=Yagi-Uda_Antennahttp://en.wikipedia.org/w/index.php?title=Log-periodic_antennahttp://en.wikipedia.org/w/index.php?title=File%3AAntenna.jpghttp://en.wikipedia.org/w/index.php?title=Ultrahigh_frequencyhttp://en.wikipedia.org/w/index.php?title=Very_High_Frequencyhttp://en.wikipedia.org/w/index.php?title=Yagi-Uda_antennahttp://en.wikipedia.org/w/index.php?title=Phase_%28waves%29http://en.wikipedia.org/w/index.php?title=Phased_arrayhttp://en.wikipedia.org/w/index.php?title=File%3AFelder_um_Dipol.jpghttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Magnetic_fieldhttp://en.wikipedia.org/w/index.php?title=Electric_field -
8/13/2019 Antenna (radio).pdf
5/23
Antenna (radio) 5
or at the throat of a horn) which could be considered the one active element in that antenna system. A microwave
antenna may also be fed directly from a waveguide in lieu of a (conductive) transmission line.
Cell phone base station antennas
An antenna counterpoise or ground plane is a structure of conductive material
which improves or substitutes for the ground. It may be connected to or
insulated from the natural ground. In a monopole antenna, this aids in the
function of the natural ground, particularly where variations (or limitations)of the characteristics of the natural ground interfere with its proper function.
Such a structure is normally connected to the return connection of an
unbalanced transmission line such as the shield of a coaxial cable.
An electromagnetic wave refractor in some aperture antennas is a component
which due to its shape and position functions to selectively delay or advance
portions of the electromagnetic wavefront passing through it. The refractor
alters the spatial characteristics of the wave on one side relative to the other
side. It can, for instance, bring the wave to a focus or alter the wave front in
other ways, generally in order to maximize the directivity of the antenna
system. This is the radio equivalent of an optical lens.
An antenna coupling network is a passive network (generally a combination
of inductive and capacitive circuit elements) used for impedance matching in between the antenna and the
transmitter or receiver. This may be used to improve the standing wave ratio in order to minimize losses in the
transmission line and to present the transmitter or receiver with a standard resistive impedance that it expects to see
for optimum operation.
Reciprocity
It is a fundamental property of antennas that the electrical characteristics o f an antennadescribed in the next section,
such as gain, radiation pattern, impedance, bandwidth, resonant frequency and polarization, are the same whether the
antenna is transmitting or receiving. For example, the "receiving pattern" (sensitivity as a function of direction) of an
antenna when used for reception is identical to the radiation pattern of the antenna when it is driven and functions as
a radiator. This is a consequence of the reciprocity theorem of electromagnetics. Therefore in discussions of antenna
properties no distinction is usually made between receiving and transmitting terminology, and the antenna can be
viewed as either transmitting or receiving, whichever is more convenient.
A necessary condition for the aforementioned reciprocity property is that the materials in the antenna and
transmission medium are linear and reciprocal. Reciprocal (or bilateral) means that the material has the same
response to an electric current or magnetic field in one direction, as it has to the field or current in the opposite
direction. Most materials used in antennas meet these conditions, but some microwave antennas use high-techcomponents such as isolators and circulators, made of nonreciprocal materials such as ferrite. These can be used to
give the antenna a different behavior on receiving than it has on transmitting, which can be useful in applications like
radar.
Parameters
Antennas are characterized by a number of performance measures which a user would be concerned with in selecting
or designing an antenna for a particular application. Chief among these relate to the directional characteristics (as
depicted in the antenna's radiation pattern) and the resulting gain. Even in omnidirectional (or weakly directional)
antennas, the gain can often be increased by concentrating more of its power in the horizontal directions, sacrificing
power radiated toward the sky and ground. The antenna's power gain (or simply "gain") also takes into account the
antenna's efficiency, and is often the primary figure of merit.
http://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Radiation_patternhttp://en.wikipedia.org/w/index.php?title=Radarhttp://en.wikipedia.org/w/index.php?title=Ferrite_%28iron%29http://en.wikipedia.org/w/index.php?title=Circulatorhttp://en.wikipedia.org/w/index.php?title=Isolator_%28microwave%29http://en.wikipedia.org/w/index.php?title=Linear_functionhttp://en.wikipedia.org/w/index.php?title=Reciprocity_%28electromagnetism%29http://en.wikipedia.org/w/index.php?title=Radiation_patternhttp://en.wikipedia.org/w/index.php?title=Radio_receiverhttp://en.wikipedia.org/w/index.php?title=Transmitterhttp://en.wikipedia.org/w/index.php?title=Polarization_%28waves%29http://en.wikipedia.org/w/index.php?title=Resonant_frequencyhttp://en.wikipedia.org/w/index.php?title=Bandwidth_%28signal_processing%29http://en.wikipedia.org/w/index.php?title=Electrical_impedancehttp://en.wikipedia.org/w/index.php?title=Radiation_patternhttp://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Optical_lenshttp://en.wikipedia.org/w/index.php?title=Coaxial_cablehttp://en.wikipedia.org/w/index.php?title=Ground_planehttp://en.wikipedia.org/w/index.php?title=Counterpoise_%28ground_system%29http://en.wikipedia.org/w/index.php?title=File%3A6_sector_site_in_CDMA.jpghttp://en.wikipedia.org/w/index.php?title=Cellular_base_stationhttp://en.wikipedia.org/w/index.php?title=Cell_phonehttp://en.wikipedia.org/w/index.php?title=Transmission_linehttp://en.wikipedia.org/w/index.php?title=Waveguide -
8/13/2019 Antenna (radio).pdf
6/23
Antenna (radio) 6
Resonant antennas are expected to be used around a particular resonant frequency; an antenna must therefore be built
or ordered to match the frequency range of the intended application. A particular antenna design will present a
particular feedpoint impedance. While this may affect the choice of an antenna, an antenna's impedance can also be
adapted to the desired impedance level of a system using a matching network while maintaining the other
characteristics (except for a possible loss of efficiency).
Although these parameters can be measured in principle, such measurements are difficult and require veryspecialized equipment. Beyond tuning a transmitting antenna using an SWR meter, the typical user will depend on
theoretical predictions based on the antenna design or on claims of a vendor.
An antenna transmits and receives radio waves with a particular polarization which can be reoriented by tilting the
axis of the antenna in many (but not all) cases. The physical size of an antenna is often a practical issue, particularly
at lower frequencies (longer wavelengths). Highly directional antennas need to be significantly larger than the
wavelength. Resonant antennas use a conductor, or a pair of conductors, each of which is about one quarter of the
wavelength in length. Antennas that are required to be very small compared to the wavelength sacrifice efficiency
and cannot be very directional. Fortunately at higher frequencies (UHF, microwaves) trading off performance to
obtain a smaller physical size is usually not required.
Resonant antennas
While there are broadband designs for antennas, the vast majority of antennas are based on the half-wave dipole
which has a particular resonant frequency. At its resonant frequency, the wavelength (figured by dividing the speed
of light by the resonant frequency) is slightly over twice the length of the half-wave dipole (thus the name). The
quarter-wave vertical antenna consists of one arm of a half-wave dipole, with the other arm replaced by a connection
to ground or an equivalent ground plane (or counterpoise). A Yagi-Uda array consists of a number of resonant dipole
elements, only one of which is directly connected to the transmission line. The quarter-wave elements of a dipole or
vertical antenna imitate a series-resonant electrical element, since if they are driven at the resonant frequency a
standing wave is created with the peak current at the feed-point and the peak voltage at the far end.
A common misconception is that the ability of a resonant antenna to transmit (or receive) fails at frequencies far
from the resonant frequency. The reason a dipole antenna needs to be used at the resonant frequency has to do with
the impedance match between the antenna and the transmitter or receiver (and its transmission line). For instance, a
dipole using a fairly thin conductor[6]
will have a purely resistive feedpoint impedance of about 63 ohms at its design
frequency. Feeding that antenna with a current of 1 ampere will require 63 volts of RF, and the antenna will radiate
63 watts (ignoring losses) of radio frequency power. If that antenna is driven with 1 ampere at a frequency 20%
higher, it will still radiate as efficiently but in order to do that about 200 volts would be required due to the change in
the antenna's impedance which is now largely reactive (voltage out of phase with the current). A typical transmitter
would not find that impedance acceptable and would deliver much less than 63 watts to it; the transmission line
would be operating at a high (poor) standing wave ratio. But using an appropriate matching network, that largereactive impedance could be converted to a resistive impedance satisfying the transmitter and accepting the available
power of the transmitter.
This principle is used to construct vertical antennas substantially shorter than the 1/4 wavelength at which the
antenna is resonant. By adding an inductance in series with the vertical antenna (a so-called loading coil) the
capacitive reactance of this antenna can be cancelled leaving a pure resistance which can then be matched to the
transmission line. Sometimes the resulting resonant frequency of such a system (antenna plus matching network) is
described using the construct of "electrical length" and the use of a shorter antenna at a lower frequency than its
resonant frequency is termed "electrical lengthening". For example, at 30 MHz (wavelength = 10 meters) a true
resonant monopole would be almost 2.5 meters (1/4 wavelength) long, and using an antenna only 1.5 meters tall
would require the addition of a loading coil. Then it may be said that the coil has "lengthened" the antenna to achievean "electrical length" of 2.5 meters, that is, 1/4 wavelength at 30 MHz where the combined system now resonates.
http://en.wikipedia.org/w/index.php?title=Electrical_lengtheninghttp://en.wikipedia.org/w/index.php?title=Electrical_lengtheninghttp://en.wikipedia.org/w/index.php?title=Electrical_lengtheninghttp://en.wikipedia.org/w/index.php?title=Loading_coil%23Radio_antennahttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Impedance_matchhttp://en.wikipedia.org/w/index.php?title=Standing_wavehttp://en.wikipedia.org/w/index.php?title=Yagi-Udahttp://en.wikipedia.org/w/index.php?title=Counterpoisehttp://en.wikipedia.org/w/index.php?title=Ground_planehttp://en.wikipedia.org/w/index.php?title=Ground_%28electricity%29http://en.wikipedia.org/w/index.php?title=Speed_of_lighthttp://en.wikipedia.org/w/index.php?title=Speed_of_lighthttp://en.wikipedia.org/w/index.php?title=Wavelengthhttp://en.wikipedia.org/w/index.php?title=Resonant_frequencyhttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Log_periodic_antennahttp://en.wikipedia.org/w/index.php?title=Polarization_%28waves%29http://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Antenna_measurementhttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Electrical_impedancehttp://en.wikipedia.org/w/index.php?title=Resonance -
8/13/2019 Antenna (radio).pdf
7/23
Antenna (radio) 7
However, the resulting resistive impedance achieved will be quite a bit lower than the impedance of a resonant
monopole, likely requiring further impedance matching. In addition to a lower radiation resistance, the reactance
becomes higher as the antenna size is reduced, and the resonant circuit formed by the antenna and the tuning coil has
a Q factor that rises and eventually causes the bandwidth of the antenna to be inadequate for the signal being
transmitted. This is the major factor that sets the size of antennas at 1 MHz and lower frequencies.
Current and voltage distribution
The antenna conductors have the lowest feed-point impedance at the resonant frequency where they are just under
1/4 wavelength long; two such conductors in line fed differentially thus realizes the familiar "half-wave dipole".
When fed with an RF current at the resonant frequency, the quarter wave element contains a standing wave with the
voltage and current largely (but not exactly) in phase quadrature, as would be obtained using a quarter wave stub of
transmission line. The current reaches a minimum at the end of the element (where it has nowhere to go!) and is
maximum at the feed-point. The voltage, on the other hand, is the greatest at the end of the conductor and reaches a
minimum (but not zero) at the feedpoint. Making the conductor shorter or longer than 1/4 wavelength means that the
voltage pattern reaches its minimum somewhere beyond the feed-point, so that the feed-point has a higher voltage
and thus sees a higher impedance, as we have noted. Since that voltage pattern is almost in phase quadrature with thecurrent, the impedance seen at the feed-point is not only much higher but mainly reactive.
It can be seen that if such an element is resonant at f0
to produce such a standing wave pattern, then feeding that
element with 3f0
(whose wavelength is 1/3 that of f0) will lead to a standing wave pattern in which the voltage is
likewise a minimum at the feed-point (and the current at a maximum there). Thus, an antenna element is also
resonant when its length is 3/4 of a wavelength (3/2 wavelength for a complete dipole). This is true for all odd
multiples of 1/4 wavelength, where the feed-point impedance is purely resistive, though larger than the resistive
impedance of the 1/4 wave element. Although such an antenna is resonant and works perfectly well at the higher
frequency, the antenna radiation pattern is also altered compared to the half-wave dipole.
The use of a monopole or dipole at odd multiples of the fundamental resonant frequency, however, does not extend
to even multiples (thus a 1/2 wavelength monopole or 1 wavelength dipole). Now the voltage standing wave is at its
peak at the feed-point, while that of the current (which must be zero at the end of the conductor) is at a minimum
(but not exactly zero). The antenna is anti-resonant at this frequency. Although the reactance at the feedpoint can be
cancelled using such an element length, the feed-point impedance is very high, and is highly dependent on the
diameter of the conductor (which makes only a small difference at the actual resonant frequency). Such an antenna
does not match the much lower characteristic impedance of available transmission lines, and is generally not used.
However some equipment where transmission lines are not involved which desire a high driving point impedance
may take advantage of this anti-resonance.
Bandwidth
Although a resonant antenna has a purely resistive feed-point impedance at a particular frequency, many (if not
most) applications require using an antenna over a range of frequencies. An antenna's bandwidth specifies the range
of frequencies over which its performance does not suffer due to a poor impedance match. Also in the case of a
Yagi-Uda array, the use of the antenna very far away from its design frequency reduces the antenna's directivity, thus
reducing the usable bandwidth regardless of impedance matching.
Except for the latter concern, the resonant frequency of a resonant antenna can always be altered by adjusting a
suitable matching network. To do this efficiently one would require remotely adjusting a matching network at the
site of the antenna, since simply adjusting a matching network at the transmitter (or receiver) would leave the
transmission line with a poor standing wave ratio.
Instead, it is often desired to have an antenna whose impedance does not vary so greatly over a certain bandwidth. Itturns out that the amount of reactance seen at the terminals of a resonant antenna when the frequency is shifted, say,
http://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Yagi-Udahttp://en.wikipedia.org/w/index.php?title=Bandwidth_%28signal_processing%29http://en.wikipedia.org/w/index.php?title=Standing_wavehttp://en.wikipedia.org/w/index.php?title=Q_factor -
8/13/2019 Antenna (radio).pdf
8/23
Antenna (radio) 8
by 5%, depends very much on the diameter of the conductor used. A long thin wire used as a half-wave dipole (or
quarter wave monopole) will have a reactance significantly greater than the resistive impedance it has at resonance,
leading to a poor match and generally unacceptable performance. Making the element using a tube of a diameter
perhaps 1/50 of its length, however, results in a reactance at this altered frequency which is not so great, and a much
less serious mismatch which will only modestly damage the antenna's net performance. Thus rather thick tubes are
typically used for the solid elements of such antennas, including Yagi-Uda arrays.
Rather than just usinga thick tube, there are similar techniques used to the same effect such as replacing thin wire
elements with cages to simulate a thicker element. This widens the bandwidth of the resonance. On the other hand,
amateur radio antennas need to operate over several bands which are widely separated from each other. This can
often be accomplished simply by connecting resonant elements for the different bands in parallel. Most of the
transmitter's power will flow into the resonant element while the others present a high (reactive) impedance and draw
little current from the same voltage. A popular solution uses so-called traps consisting of parallel resonant circuits
which are strategically placed in breaks along each antenna element. When used at one particular frequency band the
trap presents a very high impedance (parallel resonance) effectively truncating the element at that length, making it a
proper resonant antenna. At a lower frequency the trap allows the full length of the element to be employed, albeit
with a shifted resonant frequency due to the inclusion of the trap's net reactance at that lower frequency.
The bandwidth characteristics of a resonant antenna element can be characterized according to its Q, just as one uses
to characterize the sharpness of an L-C resonant circuit. However it is often assumed that there is an advantage in an
antenna havinga highQ. After all, Q is short for "quality factor" and a low Q typically signifies excessive loss (due
to unwanted resistance) in a resonant L-C circuit. However this understanding does not apply to resonant antennas
where the resistance involved is the radiation resistance, a desired quantity which removes energy from the resonant
element in order to radiate it (the purpose of an antenna, after all!). The Q is a measure of the ratio of reactance to
resistance, so with a fixed radiation resistance (an element's radiation resistance is almost independent of its
diameter) a greater reactance off-resonance corresponds to the poorer bandwidth of a very thin conductor. The Q of
such a narrowband antenna can be as high as 15. On the other hand a thick element presents less reactance at an
off-resonant frequency, and consequently a Q as low as 5. These two antennas will perform equivalently at the
resonant frequency, but the second antenna will perform over a bandwidth 3 times as wide as the "hi-Q" antenna
consisting of a thin conductor.
Gain
Gain is a parameter which measures the degree of directivity of the antenna's radiation pattern. A high-gain antenna
will preferentially radiate in a particular direction. Specifically, the antenna gain, or power gain of an antenna is
defined as the ratio of the intensity (power per unit surface) radiated by the antenna in the direction of its maximum
output, at an arbitrary distance, divided by the intensity radiated at the same distance by a hypothetical isotropic
antenna.
The gain of an antenna is a passive phenomenon - power is not added by the antenna, but simply redistributed to
provide more radiated power in a certain direction than would be transmitted by an isotropic antenna. An antenna
designer must take into account the application for the antenna when determining the gain. High-gain antennas have
the advantage of longer range and better signal quality, but must be aimed carefully in a particular direction.
Low-gain antennas have shorter range, but the orientation of the antenna is relatively inconsequential. For example, a
dish antenna on a spacecraft is a high-gain device that must be pointed at the planet to be effective, whereas a typical
Wi-Fi antenna in a laptop computer is low-gain, and as long as the base station is within range, the antenna can be in
any orientation in space. It makes sense to improve horizontal range at the expense of reception above or below the
antenna.
In practice, the half-wave dipole is taken as a reference instead of the isotropic radiator. The gain is then given indBd (decibels over dipole):
http://en.wikipedia.org/w/index.php?title=Wi-Fihttp://en.wikipedia.org/w/index.php?title=Wi-Fihttp://en.wikipedia.org/w/index.php?title=Wi-Fihttp://en.wikipedia.org/w/index.php?title=Isotropic_radiatorhttp://en.wikipedia.org/w/index.php?title=Isotropic_radiatorhttp://en.wikipedia.org/w/index.php?title=Intensity_%28physics%29http://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Radiation_resistancehttp://en.wikipedia.org/w/index.php?title=Radiation_resistancehttp://en.wikipedia.org/w/index.php?title=LC_circuithttp://en.wikipedia.org/w/index.php?title=Q_factorhttp://en.wikipedia.org/w/index.php?title=LC_circuithttp://en.wikipedia.org/w/index.php?title=Q_factor -
8/13/2019 Antenna (radio).pdf
9/23
Antenna (radio) 9
NOTE: 0 dBd = 2.15 dBi. It is vital in expressing gain values that the reference point be included.
Failure to do so can lead to confusion and error.
Effective area or aperture
The effective area or effective aperture of a receiving antenna expresses the portion of the power of a passing
electromagnetic wave which it delivers to its terminals, expressed in terms of an equivalent area. For instance, if aradio wave passing a given location has a flux of 1 pW / m
2(10
12watts per square meter) and an antenna has an
effective area of 12 m2, then the antenna would deliver 12 pW of RF power to the receiver (30 microvolts rms at 75
ohms). Since the receiving antenna is not equally sensitive to signals received from all directions, the effective area
is a function of the direction to the source.
Due to reciprocity (discussed above) the gain of an antenna used for transmitting must be proportional to its effective
area when used for receiving. Consider an antenna with no loss, that is, one whose electrical efficiency is 100%. It
can be shown that its effective area averaged over all directions must be equal to 2/4, the wavelength squared
divided by 4. Gain is defined such that the average gain over all directions for an antenna with 100% electrical
efficiency is equal to 1. Therefore the effective area Aeff
in terms of the gain G in a given direction is given by:
For an antenna with an efficiency of less than 100%, both the effective area and gain are reduced by that same
amount. Therefore the above relationship between gain and effective area still holds. These are thus two different
ways of expressing the same quantity. Aeff
is especially convenient when computing the power that would be
received by an antenna of a specified gain, as illustrated by the above example.
Radiation pattern
Polar plots of the horizontal cross sections of a
(virtual) Yagi-Uda-antenna. Outline connects
points with 3db field power compared to an ISO
emitter.
The radiation pattern of an antenna is a plot of the relative field
strength of the radio waves emitted by the antenna at different angles.It is typically represented by a three dimensional graph, or polar plots
of the horizontal and vertical cross sections. The pattern of an ideal
isotropic antenna, which radiates equally in all directions, would look
like a sphere. Many nondirectional antennas, such as monopoles and
dipoles, emit equal power in all horizontal directions, with the power
dropping off at higher and lower angles; this is called an
omnidirectional pattern and when plotted looks like a torus or donut.
The radiation of many antennas shows a pattern of maxima or "lobes"
at various angles, separated by "nulls", angles where the radiation falls
to zero. This is because the radio waves emitted by different parts of
the antenna typically interfere, causing maxima at angles where the
radio waves arrive at distant points in phase, and zero radiation at other
angles where the radio waves arrive out of phase. In a directional
antenna designed to project radio waves in a particular direction, the lobe in that direction is designed larger than the
others and is called the "main lobe". The other lobes usually represent unwanted radiation and are called "sidelobes".
The axis through the main lobe is called the "principal axis" or "boresight axis".
http://en.wikipedia.org/w/index.php?title=Antenna_boresighthttp://en.wikipedia.org/w/index.php?title=Sidelobehttp://en.wikipedia.org/w/index.php?title=Directional_antennahttp://en.wikipedia.org/w/index.php?title=Directional_antennahttp://en.wikipedia.org/w/index.php?title=Out_of_phasehttp://en.wikipedia.org/w/index.php?title=In_phasehttp://en.wikipedia.org/w/index.php?title=Interference_%28wave_propagation%29http://en.wikipedia.org/w/index.php?title=Null_%28radio%29http://en.wikipedia.org/w/index.php?title=Torushttp://en.wikipedia.org/w/index.php?title=Omnidirectional_antennahttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Monopole_antennahttp://en.wikipedia.org/w/index.php?title=Spherehttp://en.wikipedia.org/w/index.php?title=Isotropic_radiatorhttp://en.wikipedia.org/w/index.php?title=Radiation_patternhttp://en.wikipedia.org/w/index.php?title=File%3ASidelobes_en.svghttp://en.wikipedia.org/w/index.php?title=Antenna_efficiencyhttp://en.wikipedia.org/w/index.php?title=Antenna_efficiencyhttp://en.wikipedia.org/w/index.php?title=Antenna_efficiencyhttp://en.wikipedia.org/w/index.php?title=Antenna_efficiencyhttp://en.wikipedia.org/w/index.php?title=Copper_losshttp://en.wikipedia.org/w/index.php?title=Reciprocity_%28electromagnetism%29http://en.wikipedia.org/w/index.php?title=Root_mean_squarehttp://en.wikipedia.org/w/index.php?title=Radio_frequencyhttp://en.wikipedia.org/w/index.php?title=Antenna_effective_area -
8/13/2019 Antenna (radio).pdf
10/23
Antenna (radio) 10
Field regions
The space surrounding an antenna can be divided into three concentric regions: the reactive near-field, the radiating
near-field (Fresnell region) and the far-field (Fraunhofer) regions. These regions are useful to identify the field
structure in each, although there are no precise boundaries.
In the far-field region, we are far enough from the antenna to neglect its size and shape. We can assume that the
electromagnetic wave is purely a radiating plane wave (electric and magnetic fields are in phase and perpendicular to
each other and to the direction of propagation). This simplifies the mathematical analysis of the radiated field.
Impedance
As an electro-magnetic wave travels through the different parts of the antenna system (radio, feed line, antenna, free
space) it may encounter differences in impedance (E/H, V/I, etc.). At each interface, depending on the impedance
match, some fraction of the wave's energy will reflect back to the source,[7]
forming a standing wave in the feed line.
The ratio of maximum power to minimum power in the wave can be measured and is called the standing wave ratio
(SWR). A SWR of 1:1 is ideal. A SWR of 1.5:1 is considered to be marginally acceptable in low power applications
where power loss is more critical, although an SWR as high as 6:1 may still be usable with the right equipment.
Minimizing impedance differences at each interface (impedance matching) will reduce SWR and maximize power
transfer through each part of the antenna system.
Complex impedance of an antenna is related to the electrical length of the antenna at the wavelength in use. The
impedance of an antenna can be matched to the feed line and radio by adjusting the impedance of the feed line, using
the feed line as an impedance transformer. More commonly, the impedance is adjusted at the load (see below) with
an antenna tuner, a balun, a matching transformer, matching networks composed of inductors and capacitors, or
matching sections such as the gamma match.
Efficiency
Efficiency of a transmitting antenna is the ratio of power actually radiated (in all directions) to the power absorbed bythe antenna terminals. The power supplied to the antenna terminals which is not radiated is converted into heat. This
is usually through loss resistance in the antenna's conductors, but can also be due to dielectric or magnetic core
losses in antennas (or antenna systems) using such components. Such loss effectively robs power from the
transmitter, requiring a stronger transmitter in order to transmit a signal of a given strength.
For instance, if a transmitter delivers 100 W into an antenna having an efficiency of 80%, then the antenna will
radiate 80 W as radio waves and produce 20 W of heat. In order to radiate 100 W of power, one would need to use a
transmitter capable of supplying 125 W to the antenna. Note that antenna efficiency is a separate issue from
impedance matching, which may also reduce the amount of power radiated using a given transmitter. If an SWR
meter reads 150 W of incident power and 50 W of reflected power, that means that 100 W have actually been
absorbed by the antenna (ignoring transmission line losses). How much of that power has actually been radiated
cannot be directly determined through electrical measurements at (or before) the antenna terminals, but would
require (for instance) careful measurement of field strength. Fortunately the loss resistance of antenna conductors
such as aluminum rods can be calculated and the efficiency of an antenna using such materials predicted.
However loss resistance will generally affect the feedpoint impedance, adding to its resistive (real) component. That
resistance will consist of the sum of the radiation resistance Rr
and the loss resistance Rloss
. If an rms current I is
delivered to the terminals of an antenna, then a power of I2R
rwill be radiated and a power of I
2R
losswill be lost as
heat. Therefore the efficiency of an antenna is equal to Rr/ (R
r+ R
loss). Of course only the total resistance R
r+ R
loss
can be directly measured.
According to reciprocity, the efficiency of an antenna used as a receiving antenna is identical to the efficiency asdefined above. The power that an antenna will deliver to a receiver (with a proper impedance match) is reduced by
http://en.wikipedia.org/w/index.php?title=Reciprocity_%28electromagnetism%29http://en.wikipedia.org/w/index.php?title=Impedance_matchhttp://en.wikipedia.org/w/index.php?title=Reciprocity_%28electromagnetism%29http://en.wikipedia.org/w/index.php?title=Impedance_matchhttp://en.wikipedia.org/w/index.php?title=Impedance_matchhttp://en.wikipedia.org/w/index.php?title=Reciprocity_%28electromagnetism%29http://en.wikipedia.org/w/index.php?title=Root_mean_squarehttp://en.wikipedia.org/w/index.php?title=Radiation_resistancehttp://en.wikipedia.org/w/index.php?title=Copper_losshttp://en.wikipedia.org/w/index.php?title=Field_strengthhttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Copper_losshttp://en.wikipedia.org/w/index.php?title=Electrical_efficiencyhttp://en.wikipedia.org/w/index.php?title=Capacitorhttp://en.wikipedia.org/w/index.php?title=Inductorhttp://en.wikipedia.org/w/index.php?title=Balunhttp://en.wikipedia.org/w/index.php?title=Antenna_tunerhttp://en.wikipedia.org/w/index.php?title=Transformerhttp://en.wikipedia.org/w/index.php?title=Electrical_length_%28antenna%29http://en.wikipedia.org/w/index.php?title=Complex_numberhttp://en.wikipedia.org/w/index.php?title=Impedance_matchinghttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratio -
8/13/2019 Antenna (radio).pdf
11/23
Antenna (radio) 11
the same amount. In some receiving applications, the very inefficient antennas may have little impact on
performance. At low frequencies, for example, atmospheric or man-made noise can mask antenna inefficiency. For
example, CCIR Rep. 258-3 indicates man-made noise in a residential setting at 40 MHz is about 28 dB above the
thermal noise floor. Consequently, an antenna with a 20 dB loss (due to inefficiency) would have little impact on
system noise performance. The loss within the antenna will affect the intended signal and the noise/interference
identically, leading to no reduction in signal to noise ratio (SNR).
This is fortunate, since antennas at lower frequencies which are not rather large (a good fraction of a wavelength in
size) are inevitably inefficient (due to the small radiation resistance Rrof small antennas). Most AM broadcast radios
(except for car radios) take advantage of this principle by including a small loop antenna for reception which has an
extremely poor efficiency. Using such an inefficient antenna at this low frequency (5301650 kHz) thus has little
effect on the receiver's net performance, but simply requires greater amplification by the receiver's electronics.
Contrast this tiny component to the massive and very tall towers used at AM broadcast stations for transmitting at the
very same frequency, where every percentage point of reduced antenna efficiency entails a substantial cost.
The definition of antenna gain orpower gain already includes the effect of the antenna's efficiency. Therefore if one
is trying to radiate a signal toward a receiver using a transmitter of a given power, one need only compare the gain of
various antennas rather than considering the efficiency as well. This is likewise true for a receiving antenna at very
high (especially microwave) frequencies, where the point is to receive a signal which is strong compared to the
receiver's noise temperature. However in the case of a directional antenna used for receiving signals with the
intention of rejecting interference from different directions, one is no longer concerned with the antenna efficiency,
as discussed above. In this case, rather than quoting the antenna gain, one would be more concerned with the
directive gain which does not include the effect of antenna (in)efficiency. The directive gain of an antenna can be
computed from the published gain divided by the antenna's efficiency.
Polarization
Thepolarization of an antenna refers to the orientation of the electric field (E-plane) of the radio wave with respect
to the Earth's surface and is determined by the physical structure of the antenna and by its orientation; note that this
designation is totally distinct from the antenna's directionality. Thus, a simple straight wire antenna will have one
polarization when mounted vertically, and a different polarization when mounted horizontally. As a transverse wave,
the magnetic field of a radio wave is at right angles to that of the electric field, but by convention, talk of an
antenna's "polarization" is understood to refer to the direction of the electric field.
Reflections generally affect polarization. For radio waves, one important reflector is the ionosphere which can
change the wave's polarization. Thus for signals received following reflection by the ionosphere (a skywave), a
consistent polarization cannot be expected. For line-of-sight communications or ground wave propagation,
horizontally or vertically polarized transmissions generally remain in the about the same polarization state at the
receiving location. Matching the receiving antenna's polarization to that of the transmitter can make a verysubstantial difference in received signal strength.
Polarization is predictable from an antenna's geometry, although in some cases it is not at all obvious (such as for the
quad antenna). An antenna's linear polarization is generally along the direction (as viewed from the receiving
location) of the antenna's currents when such a direction can be defined. For instance, a vertical whip antenna or
WiFi antenna vertically oriented will transmit and receive in the vertical polarization. Antennas with horizontal
elements, such as most rooftop TV antennas, are horizontally polarized (broadcast TV usually uses horizontal
polarization). Even when the antenna system has a vertical orientation, such as an array of horizontal dipole
antennas, the polarization is in the horizontal direction corresponding to the current flow. The polarization of a
commercial antenna is an essential specification.
Polarization is the sum of the E-plane orientations over time projected onto an imaginary plane perpendicular to the
direction of motion of the radio wave. In the most general case, polarization is elliptical, meaning that the
http://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Ellipsehttp://en.wikipedia.org/w/index.php?title=Antenna_array_%28electromagnetic%29http://en.wikipedia.org/w/index.php?title=WiFihttp://en.wikipedia.org/w/index.php?title=Whip_antennahttp://en.wikipedia.org/w/index.php?title=Quad_antennahttp://en.wikipedia.org/w/index.php?title=Ground_wavehttp://en.wikipedia.org/w/index.php?title=Line-of-sight_propagationhttp://en.wikipedia.org/w/index.php?title=Skywavehttp://en.wikipedia.org/w/index.php?title=Ionospherehttp://en.wikipedia.org/w/index.php?title=Transverse_wavehttp://en.wikipedia.org/w/index.php?title=E-planehttp://en.wikipedia.org/w/index.php?title=Polarization_%28waves%29http://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Antenna_gainhttp://en.wikipedia.org/w/index.php?title=Loop_antenna%23AM_broadcast_receiver_loop_antennas -
8/13/2019 Antenna (radio).pdf
12/23
Antenna (radio) 12
polarization of the radio waves varies over time. Two special cases are linear polarization (the ellipse collapses into a
line) as we have discussed above, and circular polarization (in which the two axes of the ellipse are equal). In linear
polarization the electric field of the radio wave oscillates back and forth along one direction; this can be affected by
the mounting of the antenna but usually the desired direction is either horizontal or vertical polarization. In circular
polarization, the electric field (and magnetic field) of the radio wave rotates at the radio frequency circularly around
the axis of propagation. Circular or elliptically polarized radio waves are designated as right-handed or left-handed
using the "thumb in the direction of the propagation" rule. Note that for circular polarization, optical researchers use
the opposite right hand rule from the one used by radio engineers.
It is best for the receiving antenna to match the polarization of the transmitted wave for optimum reception.
Intermediate matchings will lose some signal strength, but not as much as a complete mismatch. A circularly
polarized antenna can be used to equally well match vertical or horizontal linear polarizations. Transmission from a
circularly polarized antenna received by a linearly polarized antenna (or vice versa) entails a 3dB reduction in
signal-to-noise ratio as the received power has thereby been cut in half.
Impedance matching
Maximum power transfer requires matching the impedance of an antenna system (as seen looking into the
transmission line) to the complex conjugate of the impedance of the receiver or transmitter. In the case of a
transmitter, however, the desired matching impedance might not correspond to the dynamic output impedance of the
transmitter as analyzed as a source impedance but rather the design value (typically 50 ohms) required for efficient
and safe operation of the transmitting circuitry. The intended impedance is normally resistive but a transmitter (and
some receivers) may have additional adjustments to cancel a certain amount of reactance in order to "tweak" the
match. When a transmission line is used in between the antenna and the transmitter (or receiver) one generally would
like an antenna system whose impedance is resistive and near the characteristic impedance of that transmission line
in order to minimize the standing wave ratio (SWR) and the increase in transmission line losses it entails, in addition
to supplying a good match at the transmitter or receiver itself.
Antenna tuning generally refers to cancellation of any reactance seen at the antenna terminals, leaving only a
resistive impedance which might or might not be exactly the desired impedance (that of the transmission line).
Although an antenna may be designed to have a purely resistive feedpoint impedance (such as a dipole 97% of a half
wavelength long) this might not be exactly true at the frequency that it is eventually used at. In some cases the
physical length of the antenna can be "trimmed" to obtain a pure resistance. On the other hand, the addition of a
series inductance or parallel capacitance can be used to cancel a residual capacitative or inductive reactance,
respectively.
In some cases this is done in a more extreme manner, not simply to cancel a small amount of residual reactance, but
to resonate an antenna whose resonance frequency is quite different than the intended frequency of operation. For
instance, a "whip antenna" can be made significantly shorter than 1/4 wavelength long, for practical reasons, andthen resonated using a so-called loading coil. This physically large inductor at the base of the antenna has an
inductive reactance which is the opposite of the capacitative reactance that such a vertical antenna has at the desired
operating frequency. The result is a pure resistance seen at feedpoint of the loading coil; unfortunately that resistance
is somewhat lower than would be desired to match commercial coax.[citation needed]
So an additional problem beyond canceling the unwanted reactance is of matching the remaining resistive impedance
to the characteristic impedance of the transmission line. In principle this can always be done with a transformer,
however the turns ratio of a transformer is not adjustable. A general matching network with at least two adjustments
can be made to correct both components of impedance. Matching networks using discrete inductors and capacitors
will have losses associated with those components, and will have power restrictions when used for transmitting.
Avoiding these difficulties, commercial antennas are generally designed with fixed matching elements or feedingstrategies to get an approximate match to standard coax, such as 50 or 75 Ohms. Antennas based on the dipole
http://en.wikipedia.org/w/index.php?title=Characteristic_impedancehttp://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/w/index.php?title=Coaxial_cablehttp://en.wikipedia.org/w/index.php?title=Loading_coil%23Radio_antennahttp://en.wikipedia.org/w/index.php?title=Standing_wave_ratiohttp://en.wikipedia.org/w/index.php?title=Characteristic_impedancehttp://en.wikipedia.org/w/index.php?title=Thevenin%27s_theoremhttp://en.wikipedia.org/w/index.php?title=Complex_conjugatehttp://en.wikipedia.org/w/index.php?title=Signal-to-noise_ratiohttp://en.wikipedia.org/w/index.php?title=Right_hand_rulehttp://en.wikipedia.org/w/index.php?title=Circular_polarization%23Left/right_handedness_conventionshttp://en.wikipedia.org/w/index.php?title=Circular_polarizationhttp://en.wikipedia.org/w/index.php?title=Linear_polarization -
8/13/2019 Antenna (radio).pdf
13/23
Antenna (radio) 13
(rather than vertical antennas) should include a balun in between the transmission line and antenna element, which
may be integrated into any such matching network.
Another extreme case of impedance matching occurs when using a small loop antenna (usually, but not always, for
receiving) at a relatively low frequency where it appears almost as a pure inductor. Resonating such an inductor with
a capacitor at the frequency of operation not only cancels the reactance but greatly magnifies the very small radiation
resistance of such a loop.
[citation needed]
This is implemented in most AM broadcast receivers, with a small ferriteloop antenna resonated by a capacitor which is varied along with the receiver tuning in order to maintain resonance
over the AM broadcast band
Basic antenna models
A "Turnstile" type transmitting antenna
(two dipole antennas aligned at right
angles) for a VHF low band television
broadcasting station.
There are many variations of antennas. Below are a few basic models. More
can be found in Category:Radio frequency antenna types.
The isotropic radiator is a purely theoretical antenna that radiates equally
in all directions. It is considered to be a point in space with no dimensions
and no mass. This antenna cannot physically exist, but is useful as atheoretical model for comparison with all other antennas. Most antennas'
gains are measured with reference to an isotropic radiator, and are rated in
dBi (decibels with respect to an isotropic radiator).
The dipole antenna is simply two wires pointed in opposite directions
arranged either horizontally or vertically, with one end of each wire
connected to the radio and the other end hanging free in space. Since this is
the simplest practical antenna, it is also used as a reference model for other
antennas; gain with respect to a dipole is labeled as dBd. Generally, the
dipole is considered to be omnidirectional in the plane perpendicular to the
axis of the antenna, but it has deep nulls in the directions of the axis.
Variations of the dipole include the folded dipole, the half wave antenna,
the ground plane antenna, the whip, and the J-pole.
The Yagi-Uda antenna is a directional variation of the dipole with parasitic
elements added which are functionality similar to adding a reflector and
lenses (directors) to focus a filament light bulb.
The random wire antenna is simply a very long (at least one quarter wavelength[citation needed]
) wire with one end
connected to the radio and the other in free space, arranged in any way most convenient for the space available.
Folding will reduce effectiveness and make theoretical analysis extremely difficult. (The added length helps more
than the folding typically hurts.) Typically, a random wire antenna will also require an antenna tuner, as it might
have a random impedance that varies non-linearly with frequency.
The horn antenna is used where high gain is needed, the wavelength is short (microwave) and space is not an
issue. Horns can be narrow band or wide band, depending on their shape. A horn can be built for any frequency,
but horns for lower frequencies are typically impractical. Horns are also frequently used as reference antennas.
The parabolic antenna consists of an active element at the focus of a parabolic reflector to reflect the waves into a
plane wave. Like the horn it is used for high gain, microwave applications, such as satellite dishes.
The patch antenna consists mainly of a square conductor mounted over a groundplane. Another example of a
planar antenna is the tapered slot antenna (TSA), as the Vivaldi-antenna.
http://en.wikipedia.org/w/index.php?title=Vivaldi-antennahttp://en.wikipedia.org/w/index.php?title=Patch_antennahttp://en.wikipedia.org/w/index.php?title=Satellite_dishhttp://en.wikipedia.org/w/index.php?title=Parabolic_reflectorhttp://en.wikipedia.org/w/index.php?title=Parabolic_antennahttp://en.wikipedia.org/w/index.php?title=Reference_antennahttp://en.wikipedia.org/w/index.php?title=Microwavehttp://en.wikipedia.org/w/index.php?title=Horn_antennahttp://en.wikipedia.org/w/index.php?title=Antenna_tunerhttp://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/w/index.php?title=Random_wire_antennahttp://en.wikipedia.org/w/index.php?title=Passive_radiatorhttp://en.wikipedia.org/w/index.php?title=Passive_radiatorhttp://en.wikipedia.org/w/index.php?title=Yagi-Uda_antennahttp://en.wikipedia.org/w/index.php?title=J-polehttp://en.wikipedia.org/w/index.php?title=Whip_antennahttp://en.wikipedia.org/w/index.php?title=Null_%28radio%29http://en.wikipedia.org/w/index.php?title=Omnidirectional_antennahttp://en.wikipedia.org/w/index.php?title=Reference_antennahttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=Isotropic_radiatorhttp://en.wikipedia.org/w/index.php?title=Category:Radio_frequency_antenna_typeshttp://en.wikipedia.org/w/index.php?title=File%3ASuperturnstile_Tx_Muehlacker.JPGhttp://en.wikipedia.org/w/index.php?title=Turnstile_antennahttp://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/w/index.php?title=Radiation_resistancehttp://en.wikipedia.org/w/index.php?title=Radiation_resistancehttp://en.wikipedia.org/w/index.php?title=Loop_antennahttp://en.wikipedia.org/w/index.php?title=Balun -
8/13/2019 Antenna (radio).pdf
14/23
Antenna (radio) 14
Examples of antenna models
Dipole antenna
("Rabbit ears")
for television
reception
Folded dipole
antenna
A Yagi-Uda beam antenna Rooftop TV
antenna. It is
actually three
Yagi antennas.
The longest
elements are for
the low band,
while the
medium and
short elementsare for the high
and UHF band.
A random wire
antenna
Pyramidal
microwave horn
antenna
Large
parabolic
antenna for
communicating
with spacecraft
A patch antenna and a cutaway
view
Practical antennas
"Rabbit ears" set-top antenna
Although any circuit can radiate if driven with a signal of high
enough frequency, most practical antennas are specially designed
to radiate efficiently at a particular frequency. An example of an
inefficient antenna is the simple Hertzian dipole antenna, which
radiates over a wide range of frequencies and is useful[citation
needed]
for its small size. A more efficient variation of this is thehalf-wave dipole, which radiates with high efficiency when the
signal wavelength is twice the electrical length of the antenna. One
of the goals of antenna design is to minimize the reactance of the
device so that it appears as a resistive load. An "antenna inherent
reactance" includes not only the distributed reactance of the active
antenna but also the natural reactance due to its location and
surroundings (as for example, the capacity relation inherent in the position of the active antenna relative to ground).
Reactance can be eliminated by operating the antenna at its resonant frequency, when its capacitive and inductive
reactances are equal and opposite, resulting in a net zero reactive current. If this is not possible, compensating
inductors or capacitors can instead be added to the antenna to cancel its reactance as far as the source is concerned.
Once the reactance has been eliminated, what remains is a pure resistance, which is the sum of two parts: the ohmic
http://en.wikipedia.org/w/index.php?title=File%3ATelevision_Antenna.jpghttp://en.wikipedia.org/w/index.php?title=Resonant_frequencyhttp://en.wikipedia.org/w/index.php?title=Resistivehttp://en.wikipedia.org/w/index.php?title=Electrical_reactancehttp://en.wikipedia.org/w/index.php?title=Electrical_length_%28antenna%29http://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=File%3AOld_rabbit_ears.jpghttp://en.wikipedia.org/w/index.php?title=File%3APatch_antenna_w_cutaway.gifhttp://en.wikipedia.org/w/index.php?title=File%3ACanberra_Deep_Dish_Communications_Complex_-_GPN-2000-000502.jpghttp://en.wikipedia.org/w/index.php?title=Parabolic_antennahttp://en.wikipedia.org/w/index.php?title=Parabolic_antennahttp://en.wikipedia.org/w/index.php?title=File%3ASchwarzbeck_BBHA_9120_D.jpghttp://en.wikipedia.org/w/index.php?title=File%3ALong-wire-and-balun-0a.jpghttp://en.wikipedia.org/w/index.php?title=File%3ATelevision_Antenna.jpghttp://en.wikipedia.org/w/index.php?title=Yagi_antennahttp://en.wikipedia.org/w/index.php?title=Rooftop_TV_antennahttp://en.wikipedia.org/w/index.php?title=Rooftop_TV_antennahttp://en.wikipedia.org/w/index.php?title=File%3AMontreal-tower-top.thumb2.jpghttp://en.wikipedia.org/w/index.php?title=Yagi_antennahttp://en.wikipedia.org/w/index.php?title=File%3AFolded_dipole.jpghttp://en.wikipedia.org/w/index.php?title=Folded_dipolehttp://en.wikipedia.org/w/index.php?title=File%3ARabbit-ears_dipole_antenna_with_UHF_loop_20090204.jpg -
8/13/2019 Antenna (radio).pdf
15/23
Antenna (radio) 15
resistance of the conductors, and the radiation resistance. Power absorbed by the ohmic resistance becomes waste
heat, and that absorbed by the radiation resistance becomes radiated electromagnetic energy. The greater the ratio of
radiation resistance to ohmic resistance, the more efficient the antenna.
Effect of ground
Antennas are typically used in an environment where other objects are present that may have an effect on their
performance. Height above ground has a very significant effect on the radiation pattern of some antenna types.
At frequencies used in antennas, the ground behaves mainly as a dielectric. The conductivity of ground at these
frequencies is negligible. When an electromagnetic wave arrives at the surface of an object, two waves are created:
one enters the dielectric and the other is reflected. If the object is a conductor, the transmitted wave is negligible and
the reflected wave has almost the same amplitude as the incident one. When the object is a dielectric, the fraction
reflected depends (among other things) on the angle of incidence. When the angle of incidence is small (that is, the
wave arrives almost perpendicularly) most of the energy traverses the surface and very little is reflected. When the
angle of incidence is near 90 (grazing incidence) almost all the wave is reflected.
Most of the electromagnetic waves emitted by an antenna to the ground below the antenna at moderate (say < 60)
angles of incidence enter the earth and are absorbed (lost). But waves emitted to the ground at grazing angles, far
from the antenna, are almost totally reflected. At grazing angles, the ground behaves as a mirror. Quality of
reflection depends on the nature of the surface. When the irregularities of the surface are smaller than the
wavelength, reflection is good.
The wave reflected by earth can be considered as
emitted by the image antenna.
This means that the receptor "sees" the real antenna and, under the
ground, the image of the antenna reflected by the ground. If the ground
has irregularities, the image will appear fuzzy.
If the receiver is placed at some height above the ground, waves
reflected by ground will travel a little longer distance to arrive to the
receiver than direct waves. The distance will be the same only if the
receiver is close to ground.
In the drawing at right, the angle has been drawn far bigger than in
reality. The distance between the antenna and its image is .
The situation is a bit more complex because the reflection of
electromagnetic waves depends on the polarization of the incident wave. As the refractive index of the ground
(average value ) is bigger than the refractive index of the air ( ), the direction of the component of the electric
field parallel to the ground inverses at the reflection. This is equivalent to a phase shift of radians or 180. The
vertical component of the electric field reflects without changing direction. This sign inversion of the parallel
component and the non-inversion of the perpendicular component would also happen if the ground were a goodelectrical conductor.
http://en.wikipedia.org/w/index.php?title=Refractive_indexhttp://en.wikipedia.org/w/index.php?title=Polarization_%28waves%29http://en.wikipedia.org/w/index.php?title=File%3AA6-1EN.jpghttp://en.wikipedia.org/w/index.php?title=Angle_of_incidencehttp://en.wikipedia.org/w/index.php?title=Dielectrichttp://en.wikipedia.org/w/index.php?title=Radiation_resistance -
8/13/2019 Antenna (radio).pdf
16/23
Antenna (radio) 16
The vertical component of the current reflects
without changing sign. The horizontal component
reverses sign at reflection.
This means that a receiving antenna "sees" the image antenna with the
current in the same direction if the antenna is vertical or with the
current inverted if the antenna is horizontal.
For a vertical polarized emission antenna the far electric field of the
electromagnetic wave produced by the direct ray plus the reflected ray
is:
The sign inversion for the parallel field case just changes a cosine to a
sine:
In these two equations:
is the electrical field radiated by the antenna if there were no ground.
is the wave number.
is the wave length. is the distance between antenna and its image (twice the height of the center of the antenna).
Radiation patterns of antennas and their images
reflected by the ground. At left the polarization is
vertical and there is always a maximum for
. If the polarization is horizontal as at right, there
is always a zero for .
For emitting and receiving antennas situated near the ground (in a
building or on a mast) far from each other, distances traveled by direct
and reflected rays are nearly the same. There is no induced phase shift.
If the emission is polarized vertically, the two fields (direct and
reflected) add and there is maximum of received signal. If the emission
is polarized horizontally, the two signals subtract and the received
signal is minimum. This is depicted in the image at right. In the case of
vertical polarization, there is always a maximum at earth level (left
pattern). For horizontal polarization, there is always a minimum at
earth level. Note that in these drawings the ground is considered as a perfect mirror, even for low angles of
incidence. In these drawings, the distance between the antenna and its image is just a few wavelengths. For greater
distances, the number of lobes increases.
Note that the situation is differentand more complexif reflections in the ionosphere occur. This happens over
very long distances (thousands of kilometers). There is not a direct ray but several reflected rays that add with
different phase shifts.
This is the reason why almost all public address radio emissions have vertical polarization. As public users are near
ground, horizontal polarized emissions would be poorly received. Observe household and automobile radio
receivers. They all have vertical antennas or horizontal ferrite antennas for vertical polarized emissions. In caseswhere the receiving antenna must work in any position, as in mobile phones, the emitter and receivers in base
stations use circular polarized electromagnetic waves.
Classical (analog) television emissions are an exception. They are almost always horizontally polarized, because the
presence of buildings makes it unlikely that a good emitter antenna image will appear.[citation needed]
However, these
same buildings reflect the electromagnetic waves and can create ghost images. Using horizontal polarization,
reflections are attenuated because of the low reflection of electromagnetic waves whose magnetic field is parallel to
the dielectric surface near the Brewster's angle. Vertically polarized analog television has been used in some rural
areas. In digital terrestrial television reflections are less obtrusive, due to the inherent robustness of digital signalling
and built-in error correction.
http://en.wikipedia.org/w/index.php?title=Error_detection_and_correctionhttp://en.wikipedia.org/w/index.php?title=Digital_signalhttp://en.wikipedia.org/w/index.php?title=Digital_terrestrial_televisionhttp://en.wikipedia.org/w/index.php?title=Brewster%27s_anglehttp://en.wikipedia.org/w/index.php?title=Ghosting_%28television%29http://en.wikipedia.org/wiki/Citation_neededhttp://en.wikipedia.org/w/index.php?title=Circular_polarizationhttp://en.wikipedia.org/w/index.php?title=Base_stationshttp://en.wikipedia.org/w/index.php?title=Base_stationshttp://en.wikipedia.org/w/index.php?title=Mobile_phonehttp://en.wikipedia.org/w/index.php?title=Ferrite_antennashttp://en.wikipedia.org/w/index.php?title=File%3AA6-4.jpghttp://en.wikipedia.org/w/index.php?title=Wave_lengthhttp://en.wikipedia.org/w/index.php?title=Wave_numberhttp://en.wikipedia.org/w/index.php?title=Polarization_%28waves%29http://en.wikipedia.org/w/index.php?title=File%3AA6-2.jpg -
8/13/2019 Antenna (radio).pdf
17/23
Antenna (radio) 17
Mutual impedance and interaction between antennas
Current circulating in one antenna generally induces a voltage across the feedpoint of nearby antennas or antenna
elements; note that this now is a near field phenomenon which is not properly accounted for using the Friis
transmission equation for instance. It can be described using the concept of mutual impedance between the two
antennas just as the mutual impedance describes the voltage induced in one inductor by a current through a
nearby coil coupled to it through a mutual inductance M. The mutual impedance between two antennas is
defined[8]
as:
where is the current flowing in antenna 1 and is the voltage induced at the open-circuited feedpoint of antenna
2 due only to . This parameter also permits, for instance, the calculation of the current in antenna 2 when its
feedpoint is shorted or otherwise terminated, as we shall now show.
Using the above definition, the currents and voltages present at the feedpoints of a set of coupled antennas satisfy:
where:
is the voltage at the terminals of antenna
is the current flowing between the terminals of antenna
is the driving point impedance of antenna
is the mutual impedance between antennas and .
Mutual impedance between parallel dipolesnot staggered. Curves Re and Im are the resistive
and reactive parts of the impedance.
As is the case for mutual inductances,
This is a consequence of Lorentz reciprocity. For an antenna element not connected to anything (open circuited)
one can write . But for an element which is short circuited, a current is generated across that short but no
voltage is allowed, so the corresponding . This is the case, for instance, with the so-called parasitic elements
of a Yagi-Uda antenna where the solid rod can be viewed as a dipole antenna shorted across its feedpoint. Parasitic
elements are unpowered elements that absorb and reradiate RF energy according to the induced current calculated
using such a system of equations.
http://en.wikipedia.org/w/index.php?title=Yagi-Uda_antenna%23Analysishttp://en.wikipedia.org/w/index.php?title=Parasitic_elementhttp://en.wikipedia.org/w/index.php?title=Lorentz_reciprocityhttp://en.wikipedia.org/w/index.php?title=File%3AZij-en.pnghttp://en.wikipedia.org/w/index.php?title=Mutual_inductancehttp://en.wikipedia.org/w/index.php?title=Coupled_inductorshttp://en.wikipedia.org/w/index.php?title=Friis_transmission_equationhttp://en.wikipedia.org/w/index.php?title=Friis_transmission_equationhttp://en.wikipedia.org/w/index.php?title=Near-field_region -
8/13/2019 Antenna (radio).pdf
18/23
Antenna (radio) 18
With a particular geometry, it is possible for the mutual impedance between nearby antennas to be zero. This is the
case, for instance, between the crossed dipoles used in the turnstile antenna.
Antenna gallery
Antennas and antenna arrays
A multi-band rotary directional
antenna for amateur radio use.
A
terrestrial
microwave
radio
antenna
array.
Wire dipole antenna using
open-wire ladder line
feedline for amateur radio
use.
Low cost LF time signal receiver,
antenna (left) and receiver
Rotatable log-periodic array for
VHF and UHF.
Shortwave antennas in Delano,
California.
AM loop antenna
Antennas and supporting structures
A building rooftop supporting
numerous dish and sectored
mobile telecommunications
antennas (Doncaster, Victoria,
Australia).
A water tower in Palmerston,
Northern Territory with radio
broadcasting and
communications antennas.
A three-sector telephone site in
Mexico City.
Telephone site concealed as a
palm tree.
http://en.wikipedia.org/w/index.php?title=File%3APalmCellTower.jpghttp://en.wikipedia.org/w/index.php?title=File%3ABase_station_mexico-city.JPGhttp://en.wikipedia.org/w/index.php?title=File%3APalmerston-water-tank.jpghttp://en.wikipedia.org/w/index.php?title=Northern_Territoryhttp://en.wikipedia.org/w/index.php?title=Palmerston%2C_Northern_Territoryhttp://en.wikipedia.org/w/index.php?title=Water_towerhttp://en.wikipedia.org/w/index.php?title=File%3ADoncastertower.JPGhttp://en.wikipedia.org/w/index.php?title=Australiahttp://en.wikipedia.org/w/index.php?title=Victoria_%28Australia%29http://en.wikipedia.org/w/index.php?title=Doncaster%2C_Victoriahttp://en.wikipedia.org/w/index.php?title=File%3APhilco_am_loop.jpghttp://en.wikipedia.org/w/index.php?title=Loop_antennahttp://en.wikipedia.org/w/index.php?title=File%3ADelano_VOA.jpghttp://en.wikipedia.org/w/index.php?title=Delano%2C_Californiahttp://en.wikipedia.org/w/index.php?title=Delano%2C_Californiahttp://en.wikipedia.org/w/index.php?title=File%3AVHF_UHF_LP-antenna.JPGhttp://en.wikipedia.org/w/index.php?title=File%3ALow_cost_DCF77_receiver.jpghttp://en.wikipedia.org/w/index.php?title=Time_signalhttp://en.wikipedia.org/w/index.php?title=Low_frequencyhttp://en.wikipedia.org/w/index.php?title=File%3ALadderlineW3NP.JPGhttp://en.wikipedia.org/w/index.php?title=Ladder_linehttp://en.wikipedia.org/w/index.php?title=Dipole_antennahttp://en.wikipedia.org/w/index.php?title=File%3ASpace_diversity.gifhttp://en.wikipedia.org/w/index.php?title=File%3AAntenna_d44ac.jpghttp://en.wikipedia.org/w/index.php?title=Turnstile_antenna -
8/13/2019 Antenna (radio).pdf
19/23
Antenna (radio) 19
Diagrams as part of a system
Antennas may be connected through a
multiplexing arrangement in some applications
like this trunked two-way radio example.
Antenna network for an emergency medical services base station.
Notes
[1] http://en.wikipedia.org/w/index. php?title=Template:Antennas&action=edit
[2] In the context of electrical engineering and physics, the plural of antenna is antennas, and it has been this way since about 1950 (or earlier),
when a cornerstone textbook in this field,Antennas, was published by the physicist and electrical engineer John D. Kraus of The Ohio State
University. Besides in the title, Dr. Kraus noted this in a footnote on the first page of his book. Insects may have "antennae", but this form is
not used in the context of electronics or physics.[3] For example http://www.telegraph.co.uk/science/science-news/7810454/British-scientists-launch-major-radio-telescope.html; http://
www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf09377.html; http://www.ska.ac.za/media/meerkat_cad.php
[4] http://ieeexplore.ieee.org/xpl/RecentIssue.jsp?reload=true&punumber=8
[5] "Salvan: Cradle of Wireless, How Marconi Conducted Early Wireless Experiments in the Swiss Alps", Fred Gardiol & Yves Fournier,
Microwave Journal, February 2006, pp. 124-136.
[6][6] This example assumes a length to diameter ratio of 1000.
[7] Impedance is caused by the same physics as refractive index in optics, although impedance effects are typically one dimensional, where
effects of refractive index is three dimensional.
[8][8] Principles of Antenna Theory, Kai Fong Lee, 1984, John Wiley and Sons Ltd., ISBN 0-471-90167-9
References
General references
Antenna Theory (3rd edition), by C. Balanis, Wiley, 2005, ISBN 0-471-66782-X;
Antenna Theory and Design (2nd edition), by W. Stutzman and G. Thiele, Wiley, 1997, ISBN 0-471-02590-9;
Antennas (3rd edition), by J. Kraus and R. Marhefka, McGraw-Hill, 2001, ISBN 0-07-232103-2;
Antennenbuch, by Karl Rothammel, publ. Franck'sche Verlagshandlung Stuttgart, 1991, ISBN 3-440-05853-0;
other editions (http://www.worldcat.org/oclc/65969707?tab=editions) (in German)
Antennas for portable Devices (http://www1.i2r.a-star.edu.sg/~chenzn), Zhi Ning Chen (edited), John Wiley
& Sons in March 2007
Broadband Planar Antennas: Design and Applications, Zhi Ning Chen and M. Y. W. Chia, John Wiley & Sons in
February 2006
The ARRL Antenna Book (15th edition), ARRL, 1988, ISBN 0-87259-206-5
http://www1.i2r.a-star.edu.sg/~chenznhttp://www.worldcat.org/oclc/65969707?tab=editionshttp://en.wikipedia.org/w/index.php?title=Karl_Rothammelhttp://en.wikipedia.org/w/index.php?title=Refractive_indexhttp://ieeexplore.ieee.org/xpl/RecentIssue.jsp?reload=true&punumber=8http://www.ska.ac.za/media/meerkat_cad.phphttp://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf09377.html;http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf09377.html;http://www.telegraph.co.uk/science/science-news/7810454/British-scientists-launch-major-radio-telescope.html;http://en.wikipedia.org/w/index.php?title=Physicshttp://en.wikipedia.org/w/index.php?title=Electronicshttp://en.wikipedia.org/w/index.php?title=Antenna_%28biology%29http://en.wikipedia.org/w/index.php?title=Insecthttp://en.wikipedia.org/w/index.php?title=The_Ohio_State_Universityhttp://en.wikipedia.org/w/index.php?title=The_Ohio_State_Universityhttp://en.wikipedia.org/w/index.php?title=John_D._Kraushttp://en.wikipedia.org/w/index.php?title=Physicshttp://en.wikipedia.org/w/index.php?title=Electrical_engineeringhttp://en.wikipedia.org/w/index.php?title=Template:Antennas&action=edithttp://en.wikipedia.org/w/index.php?title=File%3ABase_station_antenna_network.svghttp://en.wikipedia.org/w/index.php?title=File%3ATrunked_5ch_central_control.svghttp://en.wikipedia.org/w/index.php?title=Two-way_radiohttp://en.wikipedia.org/w/index.php?title=Trunked_radio_systemhttp://e