preparation and characterisation of potassium ammonium ... · used mainly in formulating ammonium...
Post on 17-Dec-2018
221 Views
Preview:
TRANSCRIPT
Michael K. OPOKU and Bogdan Z. DLUGOGORSKI*
Priority Research Centre for Energy
Faculty of Engineering and Built Environment
The University of Newcastle
Callaghan, NSW 2308, Australia
*Corresponding author. Email: Bogdan.Dlugogorski@newcastle.edu.au
Preparation and characterisation of potassium ammonium
nitrates (Kx(NH4)1-xNO3)
The use of ammonium nitrate as an ingredient in explosives has increased significantly
around the world due to demand for minerals and raw materials. Ammonium nitrate is a
feedstock for making emulsion explosives as well as ammonium nitrate and fuel oil explosives,
both commonly applied in open-cut mining operations. Decomposition of ammonium nitrate
may release red clouds of nitrogen oxides, especially under wet-rock blasting conditions.
Doping NH4NO3 with potassium may decrease the amount of emitted NOx. In this
contribution, we report the preparation and characterisation of co-recrystallised ammonium and
potassium nitrates, for future investigations on emissions of NOx from decomposition of these
materials. The results indicate the existence of solid solutions of potassium and ammonium
nitrates below 1 mol % K and between 5 and 25 mol % K.
1. INTRODUCTION
Ammonium nitrate (AN) constitutes a major component in industrial explosives,
used mainly in formulating ammonium nitrate and fuel oil (ANFO) explosives, as well
as emulsion explosives. Under adverse conditions of rock type and presence of
ground water, blasting of ANFO, or blends of ANFO and emulsion explosives may
release substantial amounts of nitrogen oxides, especially under lean fuel oil
conditions (Sapko et al. 2002). In recent years in Australia, the emissions of NOx
during blasting in mining operations have come under intense scrutiny of regulatory
bodies and concerned citizens, as such emissions pose environmental and health risks;
in particular, when orange clouds, characteristic of high levels of NO2 and NO, do not
dissipate rapidly and drift into populated areas surrounding the mines. Thus, there is a
great interest in industry for gaining improved understanding of the formation of NOx
during blasting, and finding practical solutions to remedy the problem (Rowland et al.
2001; Sapko et al. 2002).
Decomposition chemistry of ammonium nitrate has been studied extensively and
several modes of decomposition reaction mechanisms have been proposed, as function
of pressure, temperature, confinement, heating rate, samples sizes, and presence of
alkali and alkali earth nitrates (Gunawana and Zhang 2009; Jones et al. 1999;
Langfelderova 1982; Oxley et al. 1992; Turcotte et al. 2003). The initial step in
decomposition of AN in the condensed phase involves an endothermic proton transfer
from the ammonium ion (NH4+) to the nitrate ion (NO3
-) to form nitric acid (HNO3)
and ammonia (NH3), followed by decomposition of nitric acid itself (Eq. 1) (Brill et al.
1993; Brower et al. 1989; Chien et al. 2010; Oxley et al. 1989; Sinditskii et al. 2005;
Vyazovkin et al. 2001; Wu et al. 2007). Although, several reaction pathways for the
proton transfer have been proposed by different research groups, consensus exists that
the overall decomposition process of AN yields mostly H2O and N2O (Eq. 2), (Brill et
al. 1993; Brower et al. 1989; Chien et al. 2010; Oxley et al. 1989; Sinditskii et al.
2005; Vyazovkin et al. 2001; Wu et al. 2007).
NH4NO3 → NH3(g) + HNO3(g) (1)
NH4NO3 → N2O + 2H2O (2)
It is also well appreciated that fast decomposition of ammonium nitrate between 200
to 230 oC results in release of NO gas (Eq. 3) (Oommen and Jain 1999).
2 NH4NO3 → N2 + 2 NO + 4 H2O (3)
Oommen and Jain (1999) reported that AN deflagration engenders a different reaction
mechanism that yields both NO and NO2 (Eq. 4), while AN detonation follows yet
another reaction pathway (Eq. 5) that produces N2 and NO2. The presence of NO and
NO2 in decomposition gases of AN was also observed by other researchers (Brill et al.
1993).
8 NH4NO3 → 5 N2 + 4 NO + 2 NO2 + 16 H2O (4)
4 NH4NO3 → 3 N2 + 2 NO2 + 8 H2O (5)
In mining, the formation of nitrogen oxides (mainly N2O, NO, and NO2) during
thermal decomposition, deflagration or detonation of ammonium nitrate poses risks to
both people and the environment. It has been reported that addition of alkali and
alkali earth salts to AN can lower the emissions of nitrogen oxides during AN
decomposition (Kaljuvee et al. 2009; Klimova et al. 2011; Oxley et al. 2002; Rudjak
et al. 2010; Sapko et al. 2002).
Oxley et al. (Oxley et al. 2002) observed that thermal stability of AN doped with
alkali and alkali earth nitrates is related to the N2O/N2 ratio in gaseous products.
These authors ground different weight percentages of calcium, potassium, and sodium
nitrate salts together with AN, and studied the thermal decomposition of the mixtures.
The results indicated that the more stabilising the additives, the lower the N2O/N2
ratio. Unfortunately, Oxley et al. reported no measurements of concentrations of NO
and NO2. Two further observations of Oxley et al. are important. Firstly, when
calcium, potassium, and sodium nitrates were added to AN, there was almost no
change in the decomposition temperatures of the mixtures compared with the
decomposition of pure AN. Secondly, a mixture containing 10 mol % potassium
nitrate exhibited a lower N2O/N2 ratio compared with that of pure AN. Likewise,
other researchers have demonstrated increased stability of AN doped with K as a
consequence of the transformation of AN from crystalline phase IV to crystalline
phase III (Li et al. 2009; Oommen and Jain 1999; Vargeese et al. 2010; Wu et al.
2008). However, the mode of decomposition of mixed nitrate crystals of AN doped
with K remains unknown, prompting the present study.
In this contribution, we investigate the effect of the presence of potassium nitrate
on the crystal structure of mixed salts for potential application in industrial explosives,
to minimise the formation of nitrogen oxides. In the first phase of the study, reported
in this contribution, we attempt to crystallise solid solutions of potassium and
ammonium nitrates, and characterise them by powder XRD (X-ray diffraction), SEM-
EDS (scanning electron microscopy – energy dispersive spectroscopy) and ICP-OES
(inductively coupled plasma – optical emission spectroscopy). We also report the
formation of two crystalline phases at low (2-4 mol %) and high (>20 mol %)
concentrations of potassium in the crystallisation solution; mol % is based only on K+
and NH4+ and does not include the solution water. The thermal and explosive
decomposition of the mixed salts will be reported in a subsequent publication.
2. EXPERIMENTAL
2.1. Materials
Pure ammonium nitrate and potassium nitrate salts were used as precursors in the
preparation of mixed salts. AN (crystalline 99.9 wt % pure (dry basis)) was supplied
by Dyno Nobel Asia Pacific Pty Ltd. Potassium nitrate salt (UNIVAR reagent 99.5
%) was purchased from Ajax Chemicals.
2.2. Crystallisation
A total of 4.0 g of AN and KNO3 salts were dissolved in 1 mL of de-ionised water
to form a supersaturated solution. The concentration of KNO3 in the mixture was
varied from 1 to 25 mol %. The supersaturated solution was placed in hot water bath
at 80 oC while the solution was agitated every 15 min intermittently for complete
dissolution. After heating the solutions for 1 h at 80 oC, the solutions were quenched
in ice-cold water bath at 1 oC to effect nucleation, growth, and precipitation of mixed
nitrate salts. Precipitated salts were filtered immediately. All precipitated samples
were stored in a desiccator for at least 48 h before characterisation.
2.3. Structural analysis
Structural characterisation of NH4NO3, KNO3, and NH4NO3/KNO3 mixtures were
analysed by Philips X’pert-MPD X-ray Diffraction system using Cu Kα1. XRD
characterisations of samples were conducted under conditions of room temperature
and atmospheric pressure. Samples were scanned from 10 o to 70
o for a total duration
of 20 min with a step size of 0.008 o at 40 kV and 40 mA operating power.
2.4. Morphological analysis
Recrystallised nitrate salts were imaged using Philips XL30 SEM coupled with
Oxford ISIS EDS for elemental analyses. Nitrate salts were carbon coated using SPI
Carbon Coating Unit prior to imaging. SEM images and EDS spectra of the nitrate
salts were obtained by scanning samples at 15 kV.
2.5. ICP analysis
The concentration of metal cations in potassium nitrate and mixed nitrate salts
were quantified using Varian 715-ES ICP Optical Emission Spectrometer. Amounts
of 250 mg of nitrate salts were dissolved in 500 ml of de-ionised water. Sample
solutions were transferred via Varian SPS 3 sample preparation system for analyses in
ICP-OES. High-Purity Standards ICP multi element standard solution containing
eight metal cations in 2.0 % HNO3 was used for calibration.
3. RESULTS AND DISCUSSION
X-ray powder diffraction (XRD) pattern of recrystallised AN is shown in Fig. 1.
At 2θ of 28.9 o, the 100 % peak, which corresponds to (111) surface and d-spacing
3.085 Å, matched very well with crystalline AN phase IV salt as can be seen in Fig. 1.
It was also observed that all other peaks characteristic of AN phase IV also matched
with those displayed by this sample. AN phase IV has orthorhombic structure that is
stable between -18 and 55 oC when dry or between -18 and 32
oC in the presence of
moisture (Dellien 1981; Oommen and Jain 1999).
Addition of 1 mol % KNO3 to AN during co-recrystallisation shows no visible
modification of the XRD pattern compared with pure AN phase IV. This amount of
KNO3 is probably at the detection limit of the XRD analysis. However, it stands to
reason to suggest that the crystal lattice of AN could accommodate 1 mol % content of
K+ ions as the ionic radius of K
+ (0.133 nm) is only slightly smaller than that NH4
+
(0.143 nm). Hence, NH4+ could undergo substitution by minor amount of K
+ in the
crystal structure without much distortion. Usually small inclusions in pure phase
cause peak broadening in XRD pattern of the main component due to stress in the
crystal structure which is observed as a small shift in the d-spacing. This is because a
number of parallel planes of small inclusions may prevent diffraction to occur at
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
10000
20000
30000
40000 ANF
Figure 1. XRD patterns of recrystallised AN salt.
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
20000
40000
KA1F
Figure 2. XRD patterns of recrystallised AN containing 1 mol % KNO3.
precise angles. However, there was no visible shift of the XRD peaks of this sample
compared with pure AN phase IV. Further analysis of a co-recrystallised sample
containing 1 mol % KNO3 and 99 mol % AN by EDS indicated the presence of K in
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
20000
40000
KA1F
Figure 27: XRD patterns of 1 mol% KNO3-AN.
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
20000
40000
KA1F
the sample. In addition, ICP-OES measurements of this sample confirmed the
presence of K. This led us to a conclusion that co-recrystallisation of 1 mol % KNO3
and 99 mol % AN probably resulted in a complete solid solution of potassium
ammonium nitrate without much distortion of the AN phase IV crystal structure.
Figure 3 shows an XRD spectrum of a co-recrystallised sample containing 2 mol
% KNO3 in balance of AN. The spectrum illustrates two crystalline phases of AN;
that is, AN phase IV with a small trace of AN phase III. AN phase III has an
orthorhombic structure which is stable between 32–84 oC but is less dense, by about
3.84 %, than AN phase IV (Oommen and Jain 1999). Co-recrystallisation of 2 mol %
KNO3 and 98 mol % AN commences to change the crystal structure of AN from phase
IV to III in order to accommodate the increased modal concentration of K+
ions. This
is evident in the XRD pattern at 2θ of 22.7 o (60 % peak), and 27.7
o (100 % peak)
which correspond to (111) and (021) planes of AN phase III as shown magnified in
the inset to Fig. 3.
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
10000
20000
30000
40000
KA2F
Figure 3. XRD patterns of co-recrystallised AN containing 2 mol % KNO3 showing phase III
(red) and phase IV (blue).
In Fig. 4, the XRD spectrum of recrystallised samples confirms that increasing
KNO3 concentration to 3 mol % in balance of AN elevates the content of phase III in
the multi-phase AN. When modal composition of KNO3 increases to 5 mol %, the
XRD peak at 2θ of 27.7 o matches well the (210) surface that corresponds to 100 %
peak of K0.05(NH4)0.95NO3. K0.05(NH4)0.95NO3 displays orthorhombic structure similar
to phase III of AN. Further increment in KNO3 concentration from 5 to 20 mol %,
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
10000
20000
30000
40000
KA2F
during preparation, reveals single phase Kx(NH4)1-xNO3 with no separate phase of
potassium nitrate, according to the XRD results as presented in Fig. 5 and Table 1.
From the overlaid spectra of Fig. 5, the largest peak at 2θ of 34.2 o corresponds to d-
spacing of 2.617 Å in samples containing 10, 15 and 20 mol % K. However, crystals
obtained from the solution of 25 mol % KNO3 and 75 mol % AN reveal the presence
of pure KNO3 phase, as indicated by the peak at 2θ of 26.9 o in the XRD
measurement. This demonstrates that 25 mol % substitution of NH4+ by K
+ exceeds
the solid solubility limit of AN crystal structure, causing the precipitation of pure
KNO3, when co-recrystallised with AN.
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
5000
10000
15000
KA3F
Figure 4. XRD patterns of co-recrystallised AN containing 3 mol % KNO3 showing phase III
(red) and phase IV (blue).
Recrystallisation of pure AN from hot saturated solution by direct quenching in
ice-cold water bath at 1 oC resulted in plate and needle-like shapes, consistently with
the results of other researchers (Vargeese et al. 2009). SEM images could not be
taken at magnification higher than 10,000×. The samples seemed to evaporate at
higher magnification even if the voltage was set as low as 5 kV. The SEM images of
recrystallised pure AN displayed sheet-like surfaces with a few embedded needle-like
crystals, as shown in Fig. 6. However, the morphology of samples of AN containing
KNO3 exhibited fused crystals with numerous cracks along the crystals boundaries, as
illustrated in Figs. 6-8. It appears that increasing concentration of K in solid solutions
induces the formation of more distinct crystals with micro tree-like cracks in addition
to crystal boundaries. This demonstrates the effect of rising stress on the crystal
structure at increasing concentration of K, leading to separation of the material into
two phases, once modal content of K reaches 25 mol %.
Position [°2Theta] (Copper (Cu))
20 30 40 50 60
Counts
0
5000
10000
15000
KA3F
EDS analyses of single crystals of nitrate salts were not possible, but bulk
qualitative EDS of recrystallised nitrate salts indicated the presence of potassium in all
the potassium ammonium nitrate salts. Figures 9-11 illustrate the characteristic peaks
Kα1 and Kβ1 of potassium, which appear at 3.314 and 3.590 keV respectively. As
expected, the intensities of the characteristics potassium peaks of Kα1 and Kβ1 increase
with increasing concentration of KNO3 in the co-recrystallised salts.
Table 1. Summary of powder XRD results of co-recrystallisation of KNO3 and AN salts.
mol % KNO3* mol % KNO3** Phase(s) Present XRD Comments
0.00 1.06 ± 0.01 AN phase IV Single phase
1.00 1.91 ± 0.03 AN phase IV Single phase
2.00 2.57 ± 0.01 AN phase III and IV Multi-phase of AN
3.00 3.43 ± 0.03 AN phase III and IV Multi-phase of AN
4.00 4.24 ± 0.05 AN phase III and IV Multi-phase of AN
5.00 11.77 ± 0.09 K0.05(NH4)0.95NO3 Single phase
10.00 17.06 ± 0.18 Kx (NH4)1-xNO3 Single phase
15.00 23.58 ± 0.23 Kx (NH4)1-xNO3 Single phase
20.00 27.74 ± 0.21 Kx (NH4)1-xNO3 Single phase
25.00 97.57 ± 1.66 Kx(NH4)1-xNO3 and
KNO3
Multi-phase of KNO3
and AN
* refers to mol % KNO3 in AN in crystallising solution, on water free basis
** refers to mol % KNO3 in mixed crystals as measured by ICP OES
15 20 25 30 35 40 45 50 55 60 652Theta (°)
20000
40000
60000
80000
Inte
nsity (
counts
)
Figure 5. XRD patterns of co-recrystallised AN containing 5-25 mol % KNO3.
15 20 25 30 35 40 45 50 55 60 652Theta (°)
20000
40000
60000
80000
Inte
nsity
(co
unts
)
Figure 6. SEM images of pure AN (left), and 1 mol % KNO3-AN (right).
Figure 7. SEM images of 2 mol% KNO3 /AN (left), and 4 mol% KNO3 /AN (right).
Figure 8. SEM images of 10 mol % KNO3 /AN (left), and 25 mol % KNO3 /AN (right).
.0 5 10 15 20
Energy (keV)
0
1
2
3
4
5
cps
KK
0 5 10 15 20Energy (keV)
0
1
2
3
4
5
6cps
K
K
Figure 9. EDS spectrums of recrystallized pure AN (left), and 4 mol % KNO3/AN (right).
0 5 10 15 20Energy (keV)
0
2
4
6
8
10
12cps
K
K
0 5 10 15 20Energy (keV)
0
5
10
15
20
cps
K
K
Figure 10. EDS spectrums of 4 mol % KNO3/AN (left), and K0.05(NH4)0.95NO3 (right).
0 5 10 15 20Energy (keV)
0
50
100
cps
K
K
0 5 10 15 20Energy (keV)
0
50
100
150
cps
K
K
Figure 11. EDS spectrums of K0.10(NH4)0.90NO3 (left), and K0.20(NH4)0.80NO3 (right).
4. CONCLUSION
Attempts were made to prepare mixed potassium ammonium nitrate salts for
potential application to minimise the formation of NOx during detonation of AN
explosives. Co-recrystallised mixed nitrate salts were prepared from pure ammonium
and potassium nitrate precursors. Powder XRD, SEM-EDS, and ICP-OES were used
to characterise the co-recrystallised salts. Co-recrystallisation of 1 mol % KNO3 and
AN resulted in a single phase, identified as AN phase IV. Increasing the concentration
of KNO3 to between 2 and 4 mol % resulted in the appearance of an additional AN
phase. Loadings of 5 to 20 mol % KNO3 formed solid solution of the form Kx(NH4)1-
xNO3, which has orthorhombic structure similar to pure AN phase III. Attempts to
increase KNO3 content in AN to 25 % led to the formation of two phases, solid
solution of the form Kx(NH4)1-xNO3 plus small phase precipitation of pure KNO3.
Acknowledgments
The authors are grateful to Professors Eric Kennedy and John Mackie of the
University of Newcastle and Dr Jeff Gore of Dyno Nobel Asia Pacific Pty Ltd for
their time and professional assistance. The first author would like to acknowledge the
financial support from the University of Newcastle Postgraduate Scholarships
(UNIPRS and UNRSC). We would like to thank Mr David Phelan and Ms Jennifer
Zobec of Electron Microscope/X-Ray Unit, The University of Newcastle for their
assistance with characterisation of the salts. This study was funded jointly by the
Australian Research Council and Dyno Nobel Asia Pacific Pty Ltd.
References
1. Brill, T. B., Brush, P. J., Patil, D. G. (1993): Thermal decomposition of energetic materials
58. Chemistry of AN and ADN near the burning surface temperature, Combustion and
Flame, 92, 178-186.
2. Brower, K. R., Oxley, J.C., Tewari, M. (1989): Evidence for homolytic decomposition of
ammonium nitrate at high temperature. J Phys. Chem. 93, 1989, 1029-33.
3. Chien,W., Chandra, D., Lau, K.H., Hildenbrand, D. L., Helmy, A.M. (2010): The
vaporization of NH4NO3, J. Chem. Thermodynamics, 42, 846-851.
4. Dellien, I. (1981): A DSC study of the phase transformations of ammonium nitrate,
Thermochim, Acta, 55, 181-191.
5. Gunawana, R., Zhang, D. (2009): Thermal stability and kinetics of decomposition of
ammonium nitrate in the presence of pyrite, Journal of Hazardous Materials 165, 751-758.
6. Jones, D.E.G., Feng, H., Mintz, K. J., Augsten, R. A. (1999): Parameters affecting the
thermal behaviour of emulsion explosives, Thermochimica Acta 331, 37-44.
7. Kaljuvee, T., Rudjak, I., Edro, E., Trikkel, A. (2009): Heating rate effect on the thermal
behavior of ammonium nitrate and its blends with limestone and dolomite, J Therm. Anal.
Calorim., 97, 215-221.
8. Klimova, I., Kaljuvee, T., Türn, L., Bender, V., Trikkel, A., Kuusik R. (2011): Interactions
of ammonium nitrate with different additives: Thermodynamic analysis, J Therm. Anal.
Calorim., 105, 13-26.
9. Langfelderova, H. (1982): Study of the influence of experimental conditions on the course
of the DSC curve of ammonium nitrate (20-140 oC), Thermochimicu Acta, 56, 385-389.
10. Li, B., Lue, C., Qiao, J. (2009): Effect of polyacrylic acid potassium salt doped phase-
sincerely ammonium nitrate, Theory and Practice of Energetic Materials, Vol VIII, 42-44.
11. Oommen, C., Jain, S.R. (1999): Ammonium nitrate: a promising rocket propellant
oxidizer, Journal of Hazardous Materials A67, 253-281.
12. Oommen, C., Jain, S. R. (1999): Phase modification of ammonium nitrate by potassium
salts, Journal of Thermal Analysis and Calorimetry, 55 (3), 903-918.
13. Oxley, J. C., Kaushik, S. M., Gilson S. N. (1989): Thermal decomposition of AN-based
composites, Thermochem. Acta 153, 269-286.
14. Oxley, J. C., Kaushik, S. M., Gilson S. N., (1992): Thermal stability and compatibility of
ammonium nitrate explosives on a small and large scale, Thermochimica Acta, 212, 77-85.
15. Oxley, J. C., Smith, J. L., Rogers, E., Ming, Y. (2002): Ammonium nitrate: thermal
stability and explosivity modifiers, Thermochim, Acta, 384, 23-45.
16. Rowland III, J.H., Mainiero, R., Hurd D.A., Jr. (2001): Factors affecting fumes production
of an emulsion and ANFO/emulsion blends, Proceedings of the Annual Conference on
Explosives and Blasting Technique, Volume II, 2001, 133-142.
17. Rudjak ,I., Kaljuvee,T. , Trikkel , A., Mikli, V. (2010): Thermal behaviour of ammonium
nitrate prills coated with limestone and dolomite powder, J Therm. Anal. Calorim., 99,
749-754.
18. Sapko, M., Rowland, J., Mainiero, R., Zlochower, I. (2002): Chemical and physical factors
that influence NOX production during blasting - Exploratory study, proceedings of the
annual conference on explosives and blasting technique ,Volume II, 317-330.
19. Sinditskii, V. P., Egorshev, V. Y., Levshenkov, A. I., Serushkin, V. V. (2005):
Ammonium nitrate: combustion mechanism and the role of additives, Propellants,
Explosives, Pyrotechnics, 30 (4), 269-280.
20. Turcotte, R., Lightfoot, P.D., Fouchard, R., Jones, D.E.G. (2003): Thermal hazard
assessment of AN and AN-based explosives, Journal of Hazardous Materials A101, 1-27.
21. Vargeese, A. A., Joshi, S. S., Krishnamurthy, V. N. (2010): Use of potassium ferrocyanide
as habit modifier in the size reduction and phase modification of ammonium nitrate
crystals in slurries, Journal of Hazardous Materials, 180, 583-589.
22. Vargeese, A. A., Joshi, S. S., Krishnamurthy, V. N. (2009): Effect of method of
crystallization on the IV–III and IV–II polymorphic transitions of ammonium nitrate,
Journal of Hazardous Materials 161, 373-379.
23. Vyazovkin, S., Clawson, J. S., Wight, C. A. (2001): Thermal dissociation kinetics of solid
and liquid ammonium nitrate. Chem. Mater., 13, 960–966.
24. Wu, H. B., Chan, M. N., Chan, C. K. (2007): FTIR Characterization of polymorphic
transformation of ammonium nitrate, Aerosol Science and Technology, 41, 581-588.
25. Wu, H. B., Chan, C. K. (2008): Effects of potassium nitrate on the solid phase transitions
of ammonium nitrate particles, Atmospheric Environment 42, 313-322.
top related