nvironental ipact o lectric oad stes1445414/... · 2020-06-23 · nvironental ipact o lectric oad...
Post on 15-Jul-2020
12 Views
Preview:
TRANSCRIPT
Environmental Impact of Electric Road Systems
A Compilation of the literature review of Work Package 2 in the FOI-platform
for Electrified Roads
Foto
: Fot
ogra
f Sat
u AB
, VTI
VTI rapport 1053APublished 2020
vti.se/publications
Lina NordinFredrik Hellman
Anders GenellMats Gustafsson Yvonne
Andersson-Sköld
VTI rapport 1053A
Environmental Impact
of Electric Road Systems
A Compilation of the literature review of Work
Package 2 in the FOI-platform for Electrified Roads
Lina Nordin
Fredrik Hellman
Anders Genell
Mats Gustafsson Yvonne
Andersson-Sköld
Author: Lina Nordin (VTI), Fredrik Hellman (VTI), Anders Genell (VTI), Mats Gustafsson
(VTI), Yvonne Andersson-Sköld, (VTI)
Reg. No., VTI: 2016/0505
Publication: VTI rapport 1053A
Published by VTI, 2020
VTI rapport 1053A
Abstract
The Swedish Government decided in 2017 to investigate different possibilities and challenges with
implementing electrified roads in Sweden and since then, the Swedish Transport Administration has a
program for investigations and research regarding electric road systems (ERS). The Research and
Innovation Platform for Electrified Roads is part of this program and the present report is a
compilation of the results derived regarding environmental impact of ERS from the work in work
package two of this platform.
The general concept of ERS is to deliver energy for charging and propulsion of vehicles while driving.
The environmental aspects that are covered in this report are mainly focusing on particles, noise and
electromagnetic field emissions. The information is attained from literature reviews and discussions
with project leaders of demonstration projects for electrified roads in Sweden. Comparisons were
made with similar existing techniques or concepts. The overall results indicate that more research is
needed on environmental impact of ERS, mainly regarding particles from the wear of conductive ERS
as well as on emissions of electromagnetic fields. It is for instance important to consider emissions
from electromagnetic fields as early on in the development phase as possible as well as looking into
the standards that regulates or need to regulate these technologies in order for them to work properly
together with other electrical devices on or close to the roads. Screening of electromagnetic fields is an
alternative, which could become a costly solution if considered later on in the process.
Title: Environmental Impact of Electric Road Systems. A Compilation of the
literature review of Work Package 2 in the FOI-platform for
Electrified Roads
Author:
Publisher:
Publication No.:
Published:
Reg. No., VTI:
ISSN:
Project:
Lina Nordin (VTI, http://orcid.org/0000-0001-9313-6238)
Fredrik Hellman (VTI, http://orcid.org/0000-0001-6122-8496)
Anders Genell (VTI)
Mats Gustafsson (VTI, http://orcid.org/0000-0001-6600-3122)
Yvonne Andersson-Sköld (VTI, http://
orcid.org/0000-0003-3075-0809)
Swedish National Road and Transport Research Institute (VTI)
www.vti.se
VTI rapport 1053A
2020
2016/0505-8.1
0347–6030
FFI Research and Innovation Platform for Electrified Roads
Commissioned by: FFI Vinnova and Swedish Transport Administration
Keywords: Electrified roads, ERS, Electric Road System, Dynamic charging,
environmental impact, noise, PM10, EMF, EMC, electrical
hypersensitivity, conductive energy transfer, inductive energy transfer,
catenary
Language: English
No. of pages: 44
VTI rapport 1053A
Referat
Sedan den svenska regeringen år 2017 beslutade att undersöka möjligheter och utmaningar med att
införa elvägar i Sverige, har Trafikverket startat ett program för utredning och forskning kring elvägar.
Resultaten som diskuteras i denna rapport kommer från det arbete som gjorts i arbetspaketet för
miljöeffekter av elvägar som bedrivits inom Forsknings- och innovationsplattformen för elvägar som
är en del av Trafikverkets elvägsprogram.
Det grundläggande konceptet med elväg är att leverera el för framdrift och laddning av fordon medan
de är i rörelse längs med vägen. De miljöeffekter som studerats via litteraturstudier har främst handlat
om partiklar, buller och elektromagnetiska fält. Jämförelser har gjorts med befintliga tekniker och
koncept som kan liknas med olika varianter av elvägar. Det sammantagna resultatet är att det behövs
mer forskning kring de miljöeffekter som elvägar kan föra med sig, främst gällande partiklar från
slitage hos de konduktiva elvägsteknikerna och elektromagnetiska fält för olika delar och komponenter
av elvägen. Det är exempelvis viktigt att tidigt se över emissioner av elektromagnetiska fält och de
standarder som antingen finns eller behövs för att kunna reglera hur dessa tekniker ska kunna fungera i
miljöer tillsammans med andra elektriska apparater. Skärmning av elektromagnetiska fält är alternativ
för att begränsa sådana emissioner men skärmning brukar bli en kostsam lösning.
Titel: Miljöeffekter av elvägar. En sammanställning av den litteraturstudie
som gjorts inom ramen för arbetspaket 2 i FOI-plattformen för elvägar
Författare:
Utgivare:
Serie och nr:
Utgivningsår:
VTI:s diarienr:
ISSN:
Projektnamn:
Uppdragsgivare:
Nyckelord:
Språk:
Antal sidor:
Lina Nordin (VTI, http://orcid.org/0000-0001-9313-6238)
Fredrik Hellman (VTI, http://orcid.org/0000-0001-6122-8496)
Anders Genell (VTI)
Mats Gustafsson (VTI, http://orcid.org/0000-0001-6600-3122)
Yvonne Andersson-Sköld (VTI, http://
orcid.org/0000-0003-3075-0809)
VTI, Statens väg- och transportforskningsinstitut
www.vti.se
VTI rapport 1053A
2020
2016/0505-8.1
0347–6030
FFI FOI Plattform för elvägar
FFI-Vinnova och Trafikverket
Elvägar, dynamisk laddning, miljöeffekter, buller PM10, EMF, EMC,
Elöverkänslighet, konduktiv energiöverföring, luftledningar, elskenor,
induktiv energiöverföring
Engelska
44
VTI rapport 1053A
Preface
This report is the result of the work package on Environmental effects of electric roads, within the
Research and Innovation Platform for Electric Roads, financed by FFI / Vinnova and the Swedish
Transport Administration. The platform is divided into several different work packages, where work
packag two was about the environmental effects that a possible roll-out of electric roads could have,
mainly in terms of particles, noise and electromagnetic fields. The report is divided into a section
about particles compiled by Fredrik Hellman with the help of Mats Gustafsson. The section on noise is
written by Anders Genell and Lina Nordin has compiled the other parts, with support from other
collegues. Yvonne Andersson Sköld has contributed with background material, discussions and expert
knowledge as well as reading and valuable comments on the content. Discussions have been
conducted within the platform for electric roads, through the reference group meetings and review
seminars conducted where external reviewer Linda Olofsson reviewed the material on which this
report is based. Discussions on electromagnetic fields have been conducted with Andreas Käck at VTI
who also reviewed the sections dealing with electromagnetic fields following comments from the
review seminar that was held on 5 December, 2019. We also want to thank Mikael Carlson at the
Swedish Electricity Safety Agency who contributed with valuable advice and comments during the
project, not least with comments regarding electromagnetic fields, in connection with the review
seminar.
Göteborg, June 2020
Lina Nordin
Arbetspaketsledare för Miljöeffekter
Arne Nåbo
Projektledare för FOI – Elvägar
VTI rapport 1053A
Quality review
An external peer review was conducted on 20 March 2020 by Stefan Grudemo, Trafikverket. Lina
Nordin has made adjustments to the final manuscript of the report. Research Director Leif Sjögren has
thereafter reviewed and approved the report for publication on 9 June 2020. The conclusions and
recommendations expressed are the authors’ and do not necessarily reflect VTI’s opinion as an
authority.
Kvalitetsgranskning
Extern peer review har genomförts den 20 mars, 2020, av Stefan Grudemo, Trafikverket. Lina Nordin
har genomfört justeringar av slutligt rapportmanus. Forskningschef Leif Sjögren har därefter granskat
och godkänt publikationen för publicering 9 juni 2020. De slutsatser och rekommendationer som
uttrycks är författarnas egna och speglar inte nödvändigtvis myndigheten VTI:s uppfattning.
VTI rapport 1053A
Contents
Summary .................................................................................................................................................9
Sammanfattning ...................................................................................................................................11
1. Introduction .....................................................................................................................................13
2. Concepts of ERS ..............................................................................................................................14
2.1. The overhead conductive technology .........................................................................................14 2.2. The in-road conductive rail technology .....................................................................................14 2.3. The on-road conductive rail technology ....................................................................................14 2.4. Inductive technologies ...............................................................................................................14
3. Environmental impact ....................................................................................................................16
3.1. Material use ................................................................................................................................16 3.2. Inhalable wear particle emissions from electric roads and vehicles ..........................................17
3.2.1. Airborne particles - a background .........................................................................................17 3.2.2. Possible sources of airborne particles related to electric road systems and vehicles ............18
3.3. Electric roads and noise .............................................................................................................20 3.3.1. Standard requirements regarding noise from electric vehicles .............................................21 3.3.2. Work environment sound ......................................................................................................23
3.4. Electromagnetic fields ................................................................................................................24 3.4.1. Electromagnetic effect on animals ........................................................................................24 3.4.2. Electromagnetic effects on plants .........................................................................................26 3.4.3. EMF effects on human health ...............................................................................................26 3.4.4. Electromagnetism in electric vehicles...................................................................................28 3.4.5. Electromagnetic fields in ERS ..............................................................................................29 3.4.6. Electromagnetic fields from the demonstration sites in Sweden ..........................................29
3.5. EMC ...........................................................................................................................................30 3.5.1. EMC in ERS .........................................................................................................................30 3.5.2. EMI tests of ERS ..................................................................................................................31
4. ERS and the impact on the landscape and nature .......................................................................32
4.1. How much extra land will be needed? .......................................................................................33
5. Discussion and conclusion ..............................................................................................................35
5.1. Energy and use of resources .......................................................................................................35 5.2. Emissions of air pollutants (PM2,5 and PM10) .........................................................................35 5.3. Noise ..........................................................................................................................................36 5.4. EMF ...........................................................................................................................................36 5.5. Comparison between different ERS technologies ......................................................................37
Referenser .............................................................................................................................................39
VTI rapport 1053A
VTI rapport 1053A 9
Summary
Environmental Impact of Electric Road Systems. A Compilation of the literature review of
Work Package 2 in the FOI-platform for Electrified Roads
by Lina Nordin (VTI), Fredrik Hellman (VTI), Anders Genell (VTI), Mats Gustafsson (VTI) and
Yvonne Andersson Sköld (VTI)
The Swedish Government decided after investigating possibilities of making road transportation fossil
free, to investigate the possibilities and challenges with introducing electrified roads in Sweden, in
2017. The Swedish Transport Administration (STA) has a program for the investigation, research and
deployment of ERS (Electrified Road System) in Sweden and the Research and Innovation Platform
for Electrified roads is part of this program. The results discussed in the present report comes from the
environmental work package within this platform.
The basic concept of ERS is to supply energy to vehicles while they are in motion. There are three
different concepts of ERS in Sweden that are under investigation. The overhead catenary concepts
transfer energy from power cables above the road, while the conductive rail techniques installed in the
road surface provides energy from beneath the vehicle and the inductive technique transfers energy
inductively from beneath the road surface.
An obvious difference from conventional roads and vehicles is that there are no exhaust particles from
the combustion in electric vehicles. The effects on the particle emissions (PM10 and PM 2.5) are
however unclear as the successively improved particle filters used in cars in recent years have reduce
the exhaust related particles from conventional vehicles. Measurements are needed to be able to
compare particles from combustion motor vehicles and electric vehicles in the same road environment.
When comparing environmental impact between different concepts it will be the amount of materials
used as well as how often parts need to be replaced, i.e. the wear and tear of the components of the
system, that will be of importance. The wear of the conductive techniques could also contribute to
emissions of PM10 particles from the contact between the electric current collector and the conductor.
Generally, when discussing noise issues and electrical vehicles the noises are reduced at velocities up
to 30 km/h for light duty vehicles and 50 km/h for heavy duty vehicles. Hence, as ERS will be
implemented on high-speed roads, noise will not be significantly reduced. There could however be
different kinds of added noise from arcing or when the pick-up slides along the current conductor.
It will be important to consider the effects of electromagnetic fields when preparing for implementing
ERS. It could for instance be necessary to investigate the needs for electromagnetic shielding both
regarding electrical devices as well as for people living close to the electric road.
The vehicles themselves should be constructed in such a way that drivers are shielded from EMF. It is
however difficult to shield magnetic fields as they will only diminish with distance from the source.
When the vehicles are not connected to the road there will not be any magnetic fields, hence people
living nearby will only be affected if someone is charging their vehicles from the ERS roads nearby.
To be able to communicate with the vehicles and power systems as well as business models included
in the ERS the need for WIFI or mobile communication will be evident. Migrating animals and
insects, bats, birds and fish are furthermore affected by EMF and special investigations and
precautions are therefore needed to understand and eliminate the risks of EMF from the whole Electric
roads system including WIFI communication.
10 VTI rapport 1053A
VTI rapport 1053A 11
Sammanfattning
Miljöeffekter av elvägar. En sammanställning av den litteraturstudie som gjorts inom ramen för
arbetspaket 2 i FOI-plattformen för elvägar
av Lina Nordin (VTI), Fredrik Hellman (VTI), Anders Genell (VTI), Mats Gustafsson (VTI) och
Yvonne Andersson Sköld (VTI)
Den svenska regeringen beslutade år 2017 att undersöka möjligheter och utmaningar med att införa
elektrifierade vägar i Sverige. Trafikverket har sedan dess startat ett program för utredning och
forskning kring elvägar i Sverige och forsknings- och innovationsplattformen för elvägar är en del av
programmet. Resultaten som diskuteras i denna rapport kommer från det arbetspaket inom plattformen
som handlar om miljö.
Elvägskonceptet handlar i princip om att väginfrastrukturen ska kunna tillhandahålla el för både
laddning och framdrift medan fordonen kör, så kallad dynamisk överföring av energi. Det finns i
nuläget (2019/2020) tre olika begrepp gällande elvägar som undersöks i Sverige. Luftledningar
överför energi via en pantograf monterad på lastbilstaket, medan konduktiva skenor installerade i
vägytan tillhandahåller energi via strömavtagare som monterats under fordonet och den induktiva
tekniken överför energi induktivt via spolar installerade under vägytan, till en mottagare som finns i
fordonet.
Elvägen skulle vid en implementering möjliggöra för en stor del elfordon på vägarna. Elfordon ger till
skillnad från fordon med förbränningsmotor inga avgaspartiklar vid framdrivning, vilket är en stor
fördel i fråga om luftkvalitet. Effekten av elfordonsanvändning på minskat partikelutsläpp (PM10 och
PM2.5) är emellertid oklar eftersom de partikelfilter som används i moderna bilar på senare år har
förbättrats vilket markant minskat avgasrelaterade partiklar från förbränningsmotordrivna fordon.
Mätningar behövs för att kunna jämföra partiklar från förbränningsmotorer och elektriska fordon i
samma vägmiljö.
Det kommer att vara mängden material och slitaget av olika delar av elvägen och elvägskomponenter
som blir viktig i fråga om miljöeffekter vid jämförelser mellan olika elvägstekniker. Slitaget av
konduktiva tekniker kan också bidra till utsläpp av PM10-partiklar från kontakten mellan ström-
avtagaren och ledaren.
För elfordon gäller generellt att ljudet är lägre än för förbränningsmotorer i hastigheter upp till 30
km/h för lätta fordon och 50 km/h för tunga fordon, vilket gör att tänkta elvägsinstallationer inte
kommer att bidra till minskat buller eftersom elvägar planeras på höghastighetsvägar. Däremot kan
olika typer av tillkommande brus från exempelvis ljusbågar eller från när strömupptagaren glider längs
den konduktiva skenan, komma att påverka ljudbilden kring elvägen.
Det är också viktigt att överväga effekterna av elektromagnetiska fält från de olika elvägskoncepten.
Emissioner från elektromagnetiska fält (EMF) och olika typer av standarder för att dessa tekniker ska
kunna fungera i miljöer tillsammans med andra elektriska apparater och radiovågor. Skärmning av
elektromagnetiska fält är alternativ för att begränsa sådana emissioner men skärmning brukar bli en
kostsam lösning och gränsvärden för denna typ av utsläpp är därför viktig att komma fram till för
respektive koncept innan en storskalig utrullning sker.
Vidare behöver fordonen byggas på ett sådant sätt att förarna är skyddade från EMF. Det är dock svårt
att skydda från magnetfält eftersom dessa i princip, endast minskar med avståndet från källan.
För att kunna kommunicera med fordon, kraftsystem och de betalsystem som ingår i elvägssystemet
kommer det också att vara viktigt med fungerande wifi eller mobilkommunikation. Migrerande djur
och insekter, fladdermöss, fåglar och fiskar påverkas vidare av EMF och särskilda undersökningar och
12 VTI rapport 1053A
försiktighetsåtgärder behövs därför för att förstå och eliminera riskerna för EMF från hela det
elektriska vägsystemet inklusive wifi-kommunikation.
VTI rapport 1053A 13
1. Introduction
The Swedish government decided after investigating possibilities of making road transportation fossil
free, to investigate the possibilities and challenges with introducing electrified roads in Sweden, in
2017 (Regeringskansliet, 2017). A lot has happened in the fields since then both globally and in
Sweden. There are now two demonstration sites up and running on regular conventional roads (eRoad
Arlanda, eHighways) and two more are in the initialization phase (EVolution Road and Smart road
Gotland). The Swedish Transport Administration (STA) is, alongside of this, also planning on a full-
scale deployment of a pilot. The STA has a program for the investigation, research and deployment of
ERS (Electrified Road System) in Sweden and the Research and Innovation Platform for Electrified
roads is part of this program. The results discussed in the present report comes from the environmental
work package within this platform.
The environmental work package is investigating and analysing possible environmental effects on
humans, animals and nature in terms of health and social impact, using literature reviews as well as
input from experts in the field.
Even though the term ERS is rather new, the concept of electric vehicles and electric transportation
goes back to the first electric vehicles, trolley buses and trains. Literature discussing ERS or different
technologies to electrify vehicles, either as stationary or dynamic transfer of energy is vast (Bi et al.,
2016; Chen, 2016; Gil and Taiber, 2014; Schulte and Ny, 2018; Tongur, 2018).
The concept with ERS is to load the electric vehicle while driving. In Sweden the focus is mainly on
three different concepts; the overhead catenary technology, much like trolleybuses, the conductive in
or on road rails technologies and the inductive technology where coils are embedded within the road
construction and energy is transferred wirelessly to the vehicle. A lot of studies regarding wireless
power transfer exists as well as the effects that Electromagnetic fields (EMF) may have on humans.
The environmental aspects that normally are considered regarding regular road and road transportation
are noise, emissions of greenhouse gases and particles. In Sweden there are also other aspects that are
investigated when it comes to road effects such as the effect that roads have on the nearby landscape,
nature and cultural heritage sites. However, when discussing ERS, effects from electricity and EMF
also needs to be included.
This investigation aims at discussing what kind of environmental changes an implementation of ERS
could have on a regular road. The concept of ERS deployment in Sweden is to use already existing
roads, hence analyses are made regarding the differences that various technologies have compared to
existing roads, in terms of noise, particle emissions, electromagnetic fields and the landscape.
Greenhouse gases are excluded from the study since there will be no tailpipe emissions from ERS
vehicles. One large difference is the power transfer which will be incorporated into the roads with
ERS.
All electric devices emit electromagnetic fields of various sizes. Since this is something that differs
from regular roads it is important to consider such effects.
14 VTI rapport 1053A
2. Concepts of ERS
There are different kinds of ERS concepts considered in this report. However new concepts and
technologies are tested, and the market and development are constantly increasing. ERS is basically
the possibility of charging your electrical vehicles from the road while driving. The different concepts
investigated in Sweden are the overhead or catenary technology, the conductive in or on-road
technologies and an inductive technology.
2.1. The overhead conductive technology
The conductive catenary system e-Highway was developed by Siemens. This system has been used at
the E16 demonstration site, close to Gävle, Sweden, and consists of overhead power lines at the height
of 5 m above the road surface (Region Gävleborg, 2015). Every 50 m, in the road side verge, there is a
support mast with a cantilever that holds the power lines. The concept is intended for trucks, and a
pantograph is mounted on the roof of the truck to connect to the overhead power cables.
This technique builds on the same concept as railways, it is a robust and proven technique and will not
have a direct impact on the road structure. There is, however, a need for a lot of infrastructure, such as
the support masts made of steel with concrete foundation. Extra longitudinal safety barriers along the
roads are also required.
2.2. The in-road conductive rail technology
The conductive in-road electric rail that Elways has developed is installed within the road structure
and transfers energy via a pick-up beneath the vehicle. The rail consists of conductive metal and
isolating plastic with a top-cover of steel. The rail is 148 mm high and 144 mm wide and will be 3-5
mm underneath the driving lane (Asplund, 2017). The rails need to be placed within reach of each
power distribution box which are located within 1500 m of each other (Asplund, 2017; NCC, 2014).
2.3. The on-road conductive rail technology
This concept consists of a rail that is attached to steel plates which are glued on to the road surface
every 1.5 m. The rail ends in a ramp that is glued to or bolted to the road surface. Since the rail is quite
heavy, 10 m of the rail weigh 350 kg it is rather fixed to the surface. The rail is designed with 5 mm
high rubber feet to allow water to flow under the rail.
The rails used in this technology are mainly made of aluminium, isolators and copper. The rails have a
life span of ten years (Zethraeus, 2017) and can resist unevenness, roughness, and up to 4-5 cm deep
potholes (Zethraeus, 2017).
This concept is being tested in a new demonstration site in Lund in Sweden with start in 2020.
2.4. Inductive technologies
There are two types of wireless power transfer used for electric vehicle solutions. Inductive power
transfer, IPT and Capacitive power transfer, CPT. The inductive technology transfers energy
magnetically between two coils. The sending coil is oscillating at high frequency which creates the
power transfer. The oscillation is also the reason for the creation of electromagnetic fields. The CPT
uses the electric fields to transfer power between metal plates. The CPT technique has low cost, is
light and has less eddy-current loss than IPT (Lu et al., 2017). It is, however, best suited to transfer
energy on shorter distances and has not yet been efficient enough for transferring energy to vehicles
while in motion.
The wireless power transfer technology that is tested in the new demonstration site in Visby, Sweden
is of the inductive type. Coils are installed within the road construction, underneath of a surface layer
VTI rapport 1053A 15
of asphalt. An electric current is induced between the copper coils in the road and a receiving coil in
the vehicle.
16 VTI rapport 1053A
3. Environmental impact
The environmental impact of ERS depends on different aspects such as materials used, the robustness
of the technique, how much and how fast the materials will wear down. The obvious improvement an
ERS would have when comparing to conventional roads with combustion driven vehicles, is the local
reduction of greenhouse gas emissions. With no combustion engines there will be no emissions of
greenhouse gases or particles from the combustion of fossil fuel. With a large-scale implementation of
electrified roads this will have a global impact as well. But how about other environmental impacts?
This section of the report will describe material usage and particles, noise emissions and
electromagnetic fields.
3.1. Material use
Each of the ERS technologies considered in Sweden are under development, and to understand how
much material that in the end will be needed, is difficult. Manufacturers are still developing their
respective technology hence the amount of materials used will shift from time to time. For this project
questions where sent to both the eHighway and eRoad Arlanda demonstration sites in Sweden,
regarding materials used, eRoad Arlanda was the only one to answer but they also mentioned to keep
in mind that the technology is under constant development.
Their rail is made from steel with the dimensions of about 0.148m x 0.144m, and apart from that,
drainpipes are used as well as different sizes of aggregates and asphalt mixtures. The pick-up consists
of plastic, and metals, such as copper, steel and aluminium.
When it comes to eHighway the answers come from reports written during the start-up phase of the
demonstration site and can of course have been altered since then. The overhead cable carrier was
made of bronze; copper and magnesium, the contact wire also seems to be made from copper and
magnesium, while the pantograph is made from steel and fiberglass plastics. The poles are made of
galvanized steel and have foundations of concrete. The poles are 12,5 meters high with a cantilever
reaching out eight to ten meters, over the road. The diameter of the poles used in the Swedish test site
are 0.57 m. One pole is used every 50 – 60 meters. Depending on where the ERS is to be installed,
there could be needs for extra safety barriers to protect road users from running into the poles in case
of an accident.
The materials used in the different ERS technologies are mainly the same and if comparing between
two or more different concepts, it is the amount of materials used that will be of greatest importance.
Here follows a simplified estimation to illustrate the importance of considering the amount of
materials used in each of the technologies.
Say for instance, for the sake of simplicity, that the electrical wiring such as in-ground cables of the
ERS that are installed in the road such as rails or inductive technologies will equal out the overhead
electrical cables of the catenary solution. Then there are still the carrier cables of the catenary solution
as well as the foundation of the support masts, the masts themselves and the pantograph.
The design of the different kinds of rail solutions are slimmer, but they need to cover the whole stretch
of the road, while the masts of the catenary solution are only needed every 50 – 60 meters. To be able
to know which one uses the least amount of material, it is crucial to know how much material that is
used in each type of technique.
Baliue (2019) compared between three different ERS concepts where the material use of the overhead
catenary concepts includes 4,8 tonnes of copper cables and 7,8 tonnes steel poles for each kilometre of
ERS. In their study the rail concept used 5 tonnes of steel for the rail. They furthermore compared the
different concepts in terms of CO2 emissions during production and found that the catenary concept
would emit about 5 times more than the rail concept.
VTI rapport 1053A 17
3.2. Inhalable wear particle emissions from electric roads and vehicles
Electric road systems where the vehicles are operated, or charged, through direct transmission of
electricity via conductive transmission through physical contact with wires or through wireless
induction, will contribute differently to particle emissions depending on type of ERS concept. As the
conductive transmission is a well-established technology for trains and tramways, knowledge of
particle emissions from rail and tramway combined with road traffic knowledge can be applied for
estimating the impact of particle emissions from ERS roads.
3.2.1. Airborne particles - a background
In principle, all human activity creates air pollution of various kinds. During the last century, the
concentrations of harmful air pollutants increased dramatically in comparison to pre-industrial
concentrations. By reducing emissions of hazardous substances such as NOx, NMVOCs, and SO2, the
air quality has generally improved in Europe during the last decades, and also in comparison to the
2010 levels (European Environment Agency 2017). Nevertheless, as the transportation and especially
road transportation is still increasing the decreases of particles are not yet at a desirable level. The
trend of reduced emissions does, however, not apply to inhalable particles which instead in general
increase, and today are considered a major health problem (European Environment Agency, 2017,
Thompson, 2018, Ostro m. fl., 2011, Brunekreef, 2007, Pope och Dockery, 2006, Brunekreef och
Forsberg, 2005, Wjst m. fl., 1993). High concentrations of small particles are often found in many
large urban areas along busy roads but also in metros and train stations (Gustafsson, 2009), where the
concentrations are particularly high in enclosed spaces such as tunnels. The particles consist of
exhaust particles and non-exhaust particles from brakes, road surfaces, tires and dust from large urban
areas.
The emissions of exhaust particles from vehicles has, as with other vehicle exhaust emissions and in
contrast to the non-exhaust sources, been significantly reduced since the introduction of particulate
filters in diesel cars (Thorpe & Harrison, 2008). One estimate is that non-exhaust related particles
account for more than 90% of the road and traffic related particles of less than 10 µm (Timmers &
Achten, 2016). Other contributors are train and rail bound traffic, other activities such as construction
sites and natural sources e.g. airborne dust from deserts and dry soils. Another important source of
dusting during the winter season in Sweden is the suspension of dust from wear of studded tires and
winter maintenance activities (Gustafsson et al., 2003; Johansson et al., 2008).
The particles are often denoted as PM (particulate matter) and usually mentioned as PM10 and PM2.5.
PM10 consists of solid or liquid particles less than 10 µm and PM2.5 of particles less than 2.5 µm. As
a result of the awareness of the dangers of these particles, the EU has set out directives on accepted
concentration levels (European Council, 2008, 1996). Under these directives, outdoor concentrations
of PM10 may exceed 50 µg/m3 for 35 days in a year and the yearly mean value may not exceed 40
µg/m3. For PM2.5 the yearly mean concentration must be lower than 25 µg/m3.
Airborne particles are identified with several serious health risks. Many epidemic studies show several
different types of adverse health effects such as early death, heart and lung diseases, negative effect on
infant’s lung development, increased asthma as well synchronic obstructive pulmonary disease
(Dockery, 1993, Ciccone, 2000, Atkinson et al., 2001, Kleinman et al. 2007, Gent et al. 2009). The
properties of the particles may vary and depend on source as well as on chemical and physical
processes that interact during the suspension time. The hazardousness of the particles depends not only
on mass concentration in the air but also on their size, chemical composition morphology and surface
properties. Particles from combustion are generally very small (a few 100 nm or less) and consists of
different kind of organic compound whereas non-combustion particles generally are larger and consist
of minerals and metals, their impact on health issues will therefore vary.
18 VTI rapport 1053A
The particles dealt with here are non-combustion in origin. The effect of particles in sizes 2,5-10 µm
have in epidemical studies been shown to have negative effects on humans with airway deceases, but
also increased acute mortality in connection to high pollution levels (Meister et al., 2012, Forsberg et
al., 2005, Lipsett et al., 2006, Ostro et al, 2000). In toxicological studies (e.g. Karlsson et al., 2005) it
has been shown that non-exhaust particles from subway traffic often are dominated by metals, mainly
Fe (iron). In cell studies these particles induce more DNA damage than mineral dominated wear
particles from road pavements. On the other hand, wear particles from road pavements have been
found to induce higher inflammatory responses (Karlsson et al., 2006, 2005; Lindbom et al., 2006).
Studies in the underground metro environment indicates that negative health problems caused by
particles emitted in the metro are not large at the observed concentrations (Larsson, 2008).
Another aspect that is important regarding exposure and consequent health impacts is the nature of the
site. If the source is in a closed room such as a subway, this means that the concentrations may be
higher than in an open space since the existing air volume is more limited. Similarly, buildings,
ceilings and trees can limit the available air volume and dispersion and aggravate the situation near the
source that generates the particles. Also, humidity, rain and wind can affect the amount both
negatively and positively. Dry environment allows the recirculation and dusting of particles to
increase, while moist road paving reduces emissions (Abu-Allaban et al. 2003). The speed and size of
vehicles also affect the amount of particles that recirculate (Abu-Allaban, et al. 2003). The smaller
particles can stay suspended while larger and heavier particles deposit on the ground. An example is
African desert dust that is carried by the wind and provides elevated PM10 values around the
Mediterranean (Artíñano et al. 2004).
Figure 1. An eHighways truck with current collector on pantograph and overhead lines. Photo: Lina
Nordin.
3.2.2. Possible sources of airborne particles related to electric road systems and vehicles
Electric road systems (ERS) can contribute to emissions of PM10 particles. The identified places are
1) the contact between the current collector (pantograph) and the overhead lines (or tracks), 2) brakes
and other moving parts, 3) tires and road surface.
VTI rapport 1053A 19
Vehicles operating on ERS roads are like regular trucks but have engine and powertrain systems more
similar to rail bound electric traffic. The vehicles will be charged either through a current collector on
the roof (pantograph) connected to overhead lines (Figure 1) or a current collector under the vehicle to
take the power from an ERS track in the road (Elways, 2018; eRoadArlanda, 2018).
Current collectors and overhead lines degrade with time because of the physical contact between them
when the vehicle runs. The wear is both mechanical and electrically induced. These are inversely
correlated to the contact pressure to the overhead line (Figure 2). Small particles are emitted when
wear occurs but can be lowered by using optimized contact pressure. ERS systems using a current
collector (pick up) under the vehicle in a track have similar wear of both track and pickup.
Figure 2. Mechanical and electrical wear on current-collectors and overhead lines as a function of
contact pressure (modified from Nylander, 2018).
It is likely that the wear will be faster on a busy ERS road as these systems (fully developed) will have
a higher vehicle density that collect electricity than a corresponding train system with one locomotive
carrying many carts. In practice, the number of particles emitted from overhead lines, ERS tracks and
current collectors will therefore probably be higher. The emitted particles will consist of metals that
are used in the conductor materials. The current collectors (pantographs) are made of graphite (C) and
overhead lines are in copper (Cu) (eHighways, 2018).
When it comes to wear from the electric current collector in the road, it is even more uncertain as these
systems are in the experimental stage. The ERS tracks in the road are made of steel and the current
collector are made of plastic, and metals, such as copper, steel and aluminium (Hörnfeldt, 2018). It is
also uncertain how the dispersion will occur as the particles possibly will be swirled around by the
turbulence from moving vehicles. However, it is a big difference between train traffic and planned
ERS roads for freight traffic. Particle measurements made on train traffic e.g. (Gustafsson, 2009) in
tunnel or station environments are relatively closed spaces with limited air volume, whereas road
freight traffic is planned along the major motorways, preferably in rural areas. Therefore, particle
dispersion will be over a reasonably large area and at lower concentrations. If the systems will be used
20 VTI rapport 1053A
for example by buses in the urban area, there may be greater risks but the number of buses that operate
these routes, will probably be quite limited or at least the same as for regular buses.
Particle emissions from brake pads on train and rail traffic, are an important source of PM10 at station
areas (Gustafsson, 2009, Abbasi et al. 2012). Also, for heavy and light duty vehicles, the brakes are a
major source of particle formation. It has been found that particle emission from braking, stands for
between 16 and 55 % by mass of the non-exhaust PM10 particles and 11-21 % of the total PM10
emissions (Grigoratos & Martini 2015). In urban areas with frequent braking, the contribution can be
as high as 55 % by mass of all PM10 non-combustion particles (Grigoratos & Martini 2015).
However, this proportion is considerably smaller for rural roads and highways with steady speed and
less braking, which is the type of road that primarily, will be used for electric roads. At road exits or
other areas where braking often occurs, the emissions may also be particularly high (Abu-Allaban et
al. 2003). It has been shown that trains using electromagnetic brakes, have lower particle emissions
(Abbasi et al. 2012).
Another source of particles relevant to all road traffic, including electric roads, is the tyre wear.
Emissions of PM10 from tires are estimated to 0.002-0.1 g/vkm for cars (Hann et al., 2018; Panko et
al., 2018). These particles may contribute both to pollution of air and as a source of microplastic (Kole
et al., 2017). It is, however, not known if these emissions are affected by the introduction of electric
roads. Electric vehicles (battery powered) are often heavier which make the emissions of wear
particles higher (Timmers and Achten, 2016). With the introduction of ERS such wear could possibly
be reduced as the batteries will be smaller and less heavy.
Resuspended dust is often identified as the main particle sources to PM10 emissions (Denby et al.,
2018; Gon et al., 2013). The dust consists mainly of wear particles from road surface, tires and brakes
or from sources nearby the road (e.g. dust from building activities, bare soils and gravel roads).
A significant source of wear particles from the road surfaces in Sweden and other northern countries,
comes from materials used in winter road maintenance as well as the wear caused by studded tyres
(Areskoug et al., 2001; Gustafsson et al., 2005; Kupiainen et al., 2016). Heavy vehicles in Sweden
does however not use studded tires. The direct emission from studded tire wear can therefore be
assumed to be the same on an electric road compared to on a normal road unless special surfacing
materials are used with other properties than conventional road materials.
The impact of road dust is affected by dust storage, traffic composition, speed and meteorology, where
the moisture of road surface is primarily an important factor of influence (Denby et al., 2013b, 2013a).
It is unclear whether any different conditions regarding these factors exist for electric roads compared
to other roads. One factor that can affect dust storage and road humidity is how the road is operated. If
the road is cleaned more often, this may cause less dust to be available for suspension.
A main difference between electric vehicles and conventional vehicles is that electric vehicles do not
emit exhaust particles from internal combustion engines and particularly NOx from diesel vehicles.
During the last decades, however, the EURO vehicle emission standards have resulted in successively
improved particle filters which have reduced the exhaust related particle emissions from both light and
heavy-duty vehicles. To be able to provide information on particulate emissions from electrical roads
and its vehicles, measurements must be made. These measurements should then be designed in a way
so that it is possible to compare with combustion motor vehicles in the same road environment.
3.3. Electric roads and noise
Traditional ICE vehicles have essentially three sources of noise: the drive train, the tyre-road contact
and aerodynamic noise. Supplying electricity to the vehicle through the infrastructure may remove the
drive train source, provided the propulsion is fully electric. There are, to our knowledge, no studies
about electric roads and the impact on noise levels or how it affects the experience of noise, but the
vehicles utilizing an electric road is in essence an electric vehicle, and there are a few studies on noise
VTI rapport 1053A 21
and electric cars. Within the European Electromobility+ research framework, one work package of the
COMPetitive Electric Town Transport (COMPETT) project lead by the Danish Road Directorate
included both a literature review (Stahlfest Holck Skov and Iversen, 2015) as well as results from
measurements in urban environments (Iversen and Stahlfest Holck Skov, 2015). The literature review
points out that there may be great opportunities to reduce noise by replacing ordinary internal
combustion engines with electric power, but that there are still considerable uncertainties about the
extent of this potential (Stahlfest Holck Skov and Iversen, 2015). There are major differences in the
outcome between different studies, and the outcome depends on how and where the study was
conducted. This depends, for example, on speed, acceleration and braking, as well as the type of tire
and road surface. Often the conditions of the reported studies were not fully documented regarding the
type of vehicle, tyres or road surface. Common for most studies is, however, that it is mainly at low
speeds that the noise reduction potential can be relatively large (Stahlfest Holck Skov and Iversen,
2015), which was also supported by calculations using the traffic noise prediction calculation model,
Nord 2000. Stahlfest Holck Skov and Iversen also performed their own measurements with four
different vehicles: Citroen Berlingo, conventional, fitted with Michelin Agilis 51 tires (71 dB); Citroen
Berlingo, Electric, with Michelin Energy saver tyres (69 dB); Nissan Leaf, Electric, with Michelin
Energy saver tires (70 dB); and VW Golf conventional, with Michelin Energy saver tires (70 dB). The
measurements were conducted at a parking space with dense graded asphalt concrete with soft binder,
located so that the measurements should not be affected by other traffic noise. In accordance with the
predominant results of the literature review, they found that noise emissions from electric vehicles are
lower than those of conventional vehicles, at low speeds. The conclusion of the study was that at low
speeds, up to about 30 km/h, the sound emission from electric vehicles was significantly lower than
from conventional vehicles. At higher speeds, the road/tire sounds completely dominate (Iversen and
Stahlfest Holck Skov, 2015; Stahlfest Holck Skov and Iversen, 2015). This indicates that the reduction
will only be noticeable in low speed areas such as in cities. It should be noted that the conclusions
from the literature review and the measurements mainly concern passenger vehicles and not heavy
trucks of buses. Ögren et al. (2018) did, however, found that the rolling noise would exceed the
propulsion noise at speeds higher than 30 km/h for light vehicles and at 50 km/h for heavy vehicles.
In general, it can, hence, be assumed from the literature review as well as from the measurements that
the difference in noise level between ICE vehicles and fully electric vehicles is negligible at speeds
above 50 km/h for most prevalent road surface conditions. At higher speeds, the tyre-road interaction
dominates the radiated sound. For an extensive description of tyre-road noise mechanisms, see e.g.
Sandberg and Ejsmont (2002).
3.3.1. Standard requirements regarding noise from electric vehicles
Regarding sound from electric vehicles, the US Pedestrian Safety Enhancement Act of 2010 (2010)
states requirements to manufacturers:
“The standard required under this section shall provide that every motor vehicle be equipped with a
method —
1) to provide blind and other pedestrians with a non-visual alert regarding the location, motion,
speed, and direction of travel of a motor vehicle that provides substantially the same
protection of such pedestrians as that provided by a motor vehicle with an internal
combustion engine; and
2) that will permit a blind or other pedestrian to determine the location, motion, speed, and
direction of travel of a motor vehicle with substantially the same degree of certainty as such
pedestrians are able to determine the location, motion, speed, and direction of travel of a
motor vehicle with an internal combustion engine.“
22 VTI rapport 1053A
Implementation of these requirements have also been adopted by the UN in Regulation No. 138 –
Uniform provisions concerning the approval of Quiet Road Transport Vehicles with regard to their
reduced audibility (2017) and a corresponding ISO standard detailing a measurement method to be
used when determining minimum sound levels, ISO 16254:2016 Acoustics — Measurement of sound
emitted by road vehicles of category M and N at standstill and low speed operation. This has resulted
in the requirement that all electric vehicles are to be equipped with warning sounds that are activated
at speeds up to 20 km/h. Whether this may have an impact on noise from electric roads mainly
depends on the speed at which the electric road is being used, but as most of the technical solutions for
electric roads, aim for higher speeds, it is unlikely that Regulation No. 138 would have an impact.
For higher speeds there would still be a possibility to reduce noise emissions from electric roads
compared to conventional ICE traffic, by applying low noise road surface materials on the electric
road. This is because the dominating source of noise from traffic at electric roads is tyre-road noise
and the lack of drive train noise makes applying low noise road surface materials particularly efficient.
As for aerodynamic noise, it will mainly occur at higher speeds where turbulent flow starts appearing
around edges of the vehicle body. For electric roads, there is a possibility that equipment such as a
pantograph on a vehicle could cause increased aerodynamic noise. There are no studies for electric
road use, but there are plenty of studies on aerodynamic noise from trains. In a study on potential noise
issues in a future development of high-speed trains in Sweden, a simple model for aerodynamic noise
from the pantograph was presented (Zhang, 2010). In short, the contribution from the pantograph was
mainly valid at speeds above 150 km/h, and this is also corroborated in modern noise prediction
calculation models where aerodynamic noise from trains is disregarded below 200 km/h. Hence, the
contribution of aerodynamic noise is likely to be small for a vehicle on an electric road. Other
technical solutions such as a pickup sliding on a rail in the road to supply electricity is an untested
system but could be more related to the rolling noise of a train and may contribute also at lower
speeds.
All vehicle types within European Union need to be approved according the UN-ECE Regulation No.
51 - Uniform provisions concerning the approval of motor vehicles having at least four wheels with
regard to their sound emissions (2015). The regulation specifies accepted noise levels as well as
conditions for measurements regarding tyres, road surface, vehicle load and driving conditions. The
regulation does not take the existence of electric roads or the associated vehicle mounted equipment
into account. It is very likely that with a wide adoption of electric roads the regulation will take these
issues into account, which points to the need for developing measurement methods and driving
conditions to capture noise from vehicles on electric roads. This is particularly important for heavy
vehicles, as there are very few studies performed on noise from fully electric or hybrid electric heavy
vehicles.
Electric roads will have the potential to contribute to an increase in the share of electric vehicles,
especially trucks, buses and other heavier vehicles, in comparison with today. At lower speeds this can
contribute to a reduced noise level. Using electric roads could also contribute to reducing the vehicle
weights as a result of smaller batteries, compared to electrical vehicles driven entirely on its own
electricity. This may also contribute to lower noise levels arising from road and tires. Depending on
the design of the road, other noise situations may occur.
From the demonstrations sites in Sweden that has been testing different ERS technologies it has been
shown that the in-road technologies will need electricity supply from cables connected transversely to
the rail in the road from the roadside area. This resulted in transverse joints at a regular interval. Even
if such transverse cuts are made small, the irregularity couldcause noises such as small thumping
noises every time a vehicle passes. Which in turn, could cause disturbing noise emissions for nearby
housing. Similar noise disturbances are those propagating from motorway expansion joints as seen at
the Gudenå Bridge in Denmark (Finne and Fryd, 2017). The noise coming from vehicles passing the
joints of the bridge had caused complaints from residents in the area. Noise measurements showed that
VTI rapport 1053A 23
such noise coming from expansions joints are needed to be taken seriously when planning for new
bridges, especially in residential areas. Even though the transverse joints of ERS roads should be less
prominent compared to bride joints, further investigations of noise from different kinds of ERS
concepts should, be relevant to consider before any large-scale implementations.
3.3.2. Work environment sound
As for the interior sound in the vehicle cabin, the greatest concern for the drivers are not any risk for
hearing damage as modern vehicles exhibit relatively low sound levels overall. The response of the
drivers to the interior sound will depend on a number of factors. Professional drivers of heavy trucks
tend to judge the interior sound differently than non-professional drivers, and one explanation can be
what the sound means to the driver. If the sound gives useful information, it is less likely to be
annoying, and a sound that holds a meaning to a driver with experience may be perceived as
meaningless (and annoying) to a driver without experience (Genell and Västfjäll, 2013). Sounds that
give information to the driver about the state of the vehicle and conditions of the road are likely to be
perceived as positive. Sounds that convey the impression of something being wrong are likely to be
stressful, if the impression is that it will affect the performance of the vehicle, and/or annoying for
sounds like rattling or squeaking that imply poor quality or minor faults. Such impressions of quality
also apply to the infrastructure and may also be conveyed via interior sound (Ihs, 2010). Potholes,
cracks, raveling etc. of the road surface will propagate as structure borne or airborne sound to the
interior. In a similar manner as for the inherent vehicle sounds, the sounds emanating from the
tyre/road interaction will be perceived by the driver as stressing or merely annoying depending on the
underlying reason for the sound, and whether it is likely that it will affect the vehicle performance, or
probability of safety or the travel time.
In the context of electric roads, there are several sources that may contribute to the interior sound. In
table 2, such sources are compared between the different types of vehicle concepts, where EV stands
for Electric Vehicle, and ICE V stands for Internal Combustion Engine Vehicle.
Table 1. Impact assessment of various aspects affecting noise emissions.
Reasons for noise emission
Conductive Catenary
Conductive rail on road
Conductive rail in road
Inductive Battery driven EV
ICE V
Noise, Vibration and Harshness from engine
No No No No No Yes
Contact between tyre and road surface
Yes Yes Yes Yes Yes Yes
Studded tyres Yes Yes Yes Yes Yes Yes
Vibrations in vehicle from irregular road surface
Yes Yes Yes Yes Yes Yes
Noise from regenerative braking of electric vehicle
Yes Yes Yes Yes Yes No
Noise from contact between current collector and rail in road
No Yes Yes No No No
Noise from contact between current collector and catenary wire
Yes No No No No No
24 VTI rapport 1053A
Reasons for noise emission
Conductive Catenary
Conductive rail on road
Conductive rail in road
Inductive Battery driven EV
ICE V
Noise from arcing on catenary wire or rail in road.
Yes Yes Yes No No No
Sounds like scraping or whistling from the pickup or pantograph, and thumping sounds from slits in
the road for power supply cables for the on-road charging infrastructure may be perceived as negative
due to the same reasons regarding stress and annoyance as sound in ordinary vehicles and roads.
Also, professional drivers are used to the interior sound environment being dominated by low
frequency sound from the engine and exhaust. When driving in purely electric mode, this dominating
sound source is removed, and all other sounds will be more prominent, further pointing to the
importance of handling potentially annoying sounds from the vehicle or the infrastructure.
3.4. Electromagnetic fields
Electromagnetic fields (EMF) are a common source of interest when it comes to electric devices,
techniques or solutions. The concerns regarding EMF in ERS is of course also of huge interest in a
work package that should consider all environmental aspects of ERS.
EMF consists, as the name imply, of two components the electric fields and the magnetic fields.
Electric fields are induced from electrical voltage and the magnetic fields are basically generated
around electric currents. Electric fields exist whenever there is an electric voltage present even though
there is no electrical current flowing in the cable, while the magnetic fields are only induced when
electrical current is flowing, such as when the lamp is switched on.
EMF has always been present on Earth. The iron core of the planet generates the electromagnetic
fields of the Earth, that are used in compasses as well as by animals, such as migratory birds.
Researchers have also concluded that large groups of birds that seem to be moving simultaneously,
generates electric fields when flying (Warnke and Luttichau, 2009) and can know how to move in
accordance with the rest of the flock by following electromagnetic signals created from their own wing
movements. Other natural EMF comes from the weather. Warnke and Luttichau described how bees
return to their home when a thunderstorm is coming by sensing the different electric charges in the air.
They furthermore described that if the natural signals would be overlapped with artificial oscillations
the rate in returning bees would rapidly decrease. This suggests that disturbing signals of EMF could
affect natural behaviour of insects and animals.
3.4.1. Electromagnetic effect on animals
The EMF limits set by WHO are set to fifty times lower than the limit where disturbances have been
found in animals. This section of the report will hence describe known effects on animals to
enlightening the risks to animals as well as humans.
Electromagnetic fields have been shown to have different kinds of effects on rats and mice. These
kinds of animals are often used in medicinal studies to help in understanding how humans would be
affected. There are for instance, studies of behaviour, stress and anti-depressive processes, memory
retention, effects on muscles as well as on cell-level, that has been conducted on mice and rats, that
indicate effects of EMF within the body.
Studies on why large groups of birds, insect swarms and schools of fish can stay together, and seem to
move simultaneously even though the groups can cover an area of 500 m2 have indicated that the
individuals of the groups are navigating by electromagnetic signals (Warnke and Luttichau, 2009).
VTI rapport 1053A 25
Warnke and Luttichau, also mentioned that signals from transmitter stations can interrupt the
commonly v-shaped formation of migrating birds.
3.4.1.1. Radiofrequency (100 kHz – 300 GHz)
Radio frequencies are found in mobile phones, broadcasting and TV, radio transceivers, radar as well
as Wi-Fi. When discussing ERS it is important to include the payment systems of the energy transfer,
will most likely will be provided via some kind of WIFI transmission.
The concern is not only regarding exposure to specific frequencies but rather the level of emission as
exposure to EMF has become more common and often without our knowledge or consent. Pall (Pall,
2018) reviewed studies on health effects from exposure to Wi-Fi and found that Wi-Fi causes
oxidative stress, sperm or testicular damage, cellular DNA damage as well as calcium overload, to
mention a few.
Favre (Favre, 2017) showed that honeybees was affected by increased amplitudes of radiofrequency
RF-EMF. Favre did sound analysis in beehives with increased EMF and found that after about 45 min
the bees started to produce sounds that were higher in frequency and amplitude than for undisturbed
bees. Other studies of bees have also shown aggressive behaviour as well as abandoning beehives (e.g.
(Warnke and Luttichau, 2009). It is hence important to take this into consideration when planning for
ERS, as the risks of bee-distinction are already a current concern.
Warnke (Warnke and Luttichau, 2009), also mentioned the interference that radiofrequency
electromagnetic fields could have on migratory birds, which was also described by (Wiltschko
Roswitha et al., 2015). Other animals that could be affected from interference in the earth’s magnetic
fields are fish and insects such as termites and ants.
One study with mice showed that mice that was treated with carcinogen and exposed to RF-EMF had
significantly higher number of tumours in lungs and livers than did non exposed mice in the control
group. The levels to which the mice was exposed was well below the exposure limits for the use of
mobile phones (Lerchl et al., 2015).
3.4.1.2. Extremely low frequencies – ELF (0 – 300Hz)
EMF in the ELF band comes from power lines, electric engines in cars, trains and tramways as well as
welding devices.
Bahaodini et al. (Bahaodini et al., 2015) showed that the sperm mobility and testosterone levels were
significantly reduced in rats when exposed to 50 Hz/1 mT. Further studies on mice concluded that
long-time exposure to ELF-EMF causes effects that are similar to physiological stress (Martínez-
Sámano et al., 2018), which was also indicated by Karimi et al (Karimi et al., 2019), whom suggested
that exposure to ELF-EMF could cause anxious state or oxidative stress. They did, however, conclude
that ELF-EMF can improve memory retention. Another study of male rats did, on the other hand, not
show any shifts in behaviour like anxiety or stress, the cognitive and memory abilities were not
affected and there were no shifts in morphology and histology of the brain after the study (Lai et al.,
2016).
Laszlo (Laszlo et al., 2018) found from a study of turkeys, that the functionality of behavioural and
physiological processes in the body of could be affected when exposed to ELF-EMF. Also insects
seem to be affected by ELF-EMF. Wyszkowa et al. (Wyszkowska et al., 2016) showed that insects are
affected by ELF-EMF both in terms of higher stress protein levels as well as in behavioural and
physiological processes. This was also concluded from the studies made by Warnke (Warnke and
Luttichau, 2009).
Besides the known fact that animals use the geomagnetic fields of the earth to navigate during
migration, they can also align their bodies along these fields. Belova and Acosta-Avalos (2015)
26 VTI rapport 1053A
mentioned that such alignment of cattle has been disturbed close to powerlines. They conclude that
variations in the magnetic field may affect the magnetic sensitivity in animals. Which in terms of ERS
e.g. could cause disruption in paths for migratory birds.
3.4.2. Electromagnetic effects on plants
It seems that electromagnetic fields act similarly in plants as in animals according to Pall (Pall, 2016).
The low frequency EMF appear to be activating calcium channels in the plasma membrane of both
plants and animals which in turn leads to diverse biological effects.
Halgamuge (2017), showed that for example maize, pea, tomato, onions and mungbean plants seemed
to be very sensitive to radio frequency EMF. It furthermore seemed as if the plants were more
responsive the frequencies between 800 and 1500 MHz.
Waldmann-Selsam et al. (Waldmann-Selsam et al., 2016) demonstrated that trees were damaged by
electromagnetic radiation from mobile phone masts. It was furthermore shown that such damage
usually starts on the side facing the mast but will extend to the rest of the tree over time. Further
studies on electromagnetic fields effect on plants are found in (Havas and Sheena Symington, 2016).
They showed that the growth of peas was markedly reduced if plants were subjected to WIFI.
Such aspects, as those mentioned above will be crucial to consider in terms of planning for ERS. If
possible, the ERS should not be placed in the vicinity of plant schools or gardens producing
vegetables.
3.4.3. EMF effects on human health
The European Commission have produced a guide for good practice concerning electromagnetic fields
and workplaces, to help implementing the Electromagnetic field directive 2013/35/EU (European
Parliament, 2013). They have differentiated between direct and indirect effects of EMF. The direct
effects mentioned are vertigo and nausea, effects on sense organs, nerves and muscles, heating of
nearby human bodies. Indirect effects are interferences with medical electronic equipment as well as
implanted medical devices or medical devices worn on body such as insulin pumps. They also list risk
for fires, explosions from ignition of flammable or explosive material, electric shock or burns if
someone mistakenly touches a conductive part within an electromagnetic field, as well as risks of
initiation of detonators. The International commission on Non-Ionizing Radiation Protection (ICNIRP)
did also mention such effects on human bodies in their guidelines for occupational and general public
exposure to EMF (Matthes and Bernhardt, 1999).
In terms of electromagnetic fields generated from powerlines and electric vehicles the frequencies
ranges in the extremely low frequency fields from 0 – 300 Hz. Bi et al. (2016) mentioned several
studies made on the effects on humans from EMF below 100 Hz. Such effects are annoyance, surface
electric-charge effects and stimulation of central and peripheral nervous tissues. Another possible
effect is where electromagnetic fields induces waves that are experienced as a sensation of a flickering
light in the corner the eye. This disorder is called retinal phosphene visualization (Fisher et al., 2014).
The World’s Health Organization (WHO) have initiated an international electromagnetic field (EMF)
project which aims at coordinating all international research regarding EMF and health effects. The
research includes studies on cells, animals and human health (WHO, 2019). 25 000 scientific papers
over a time span of 30 years have been examined and according to WHO there is no evidence that
exposure to low levels of electromagnetic fields are harmful to human health. However, long-term
effects are not satisfactory studied and further research is needed.
The project also aims at facilitating development of international standards for EMF exposure. The
guidelines that are used today differ between different countries and a common view is preferable. The
guidelines set by ICNIRP are according to WHO set in regard to when behavioural disturbances are
detected on tested animals. The limitation values for the general public are set to 50 times lower than
VTI rapport 1053A 27
the limits when the disturbances in animals are detected. It is mentioned that exposure to EMF below
the limits is safe to a scientific knowledge, not meaning that values above are harmful.
This is, however, still not enough according to the International EMF Scientist Appeal, a group of
scientists from 43 different nations engaged in the study of biological and health effects of non-
ionizing electromagnetic fields (EMF). In July 2019 they renewed the appeal they sent to the
Environmental Program of UN, UNEP, in 2015 where they ask for an independent multidisciplinary
committee to further investigate alternatives to current practices with the potential of lower human
exposures to RF (radiofrequency) and ELF fields. They further demand that children and pregnant
women should be protected and that standards and guidelines should be strengthened (EMFscientist,
2019).
They mean that several recent publications show that EMF is affecting living organisms at much lower
levels than what is set in most existing national and international guidelines (Redazione, 2015).
It is interesting to compare between the limits set by different organization. For instance, the ICNIRP
and the Swedish Radiation Safety Authority have set a limit of 61 V/m or 0.20 µT (magnetic flux
density) for mobile phone and WIFI, while the Bioinitiative.org (consisting of a group of 29
researchers from ten different nations, including three former presidents and five full members of the
Bioelectromagnetics Society, BEMS) have set the same limit at 0.033 V/m (3 µW/m2)(Carpenter and
Sage, 2007; Matthes and Bernhardt, 1999; Strandman, 2009).
The Bioinitiative have summarized a comprehensive report on how humans are affected by EMF
(Carpenter and Sage, 2007). They strongly suggest that the limits set by ICNIRP are outdated. Instead
new limits should be developed and implemented. They furthermore suggest that meanwhile setting a
planning limit of 0.1 µT for new or upgraded power lines, such as, for instance, will be used for ERS,
and 0.2 µT for all other new construction.
In the home environment there are other aspects to consider, and people with cardiac implants are for
instance to keep a safe distance from induction furnace ((European Parliament, 2013). This would
further imply safety precautions when it comes to inductive ERS.
3.4.3.1. Electromagnetic hypersensitivity
Electromagnetic hypersensitivity has been reported since the 1980’s and since then several studies
have been performed. Rubin (2005) investigated 31 experiments, including 725 patients with
electromagnetic hypersensitivity. They concluded that even though the patients experienced symptoms
that can be severe and disabling, the studies could not prove that exposure to EMF can trigger these
symptoms under blind conditions. Nevertheless, the symptoms remain and are well perceived by the
patients. Introducing an obvious and visually overwhelming sight of overhead lines will possibly
trigger such symptoms on hypersensitive people.
The Resolution 1815, set by the Parliamentary Assembly of the Council of Europe, European Union
(Parliamentary Assembly, 2011) on “The potential dangers of electromagnetic fields and their effect
on the environment” recommends that the member states should take measures to reduce the exposure
to EMF. This should be done by reconsidering the limits set by ICNIRP, as they consider those limits
having “serious limitations”. The limits should include both thermal and athermic or biological effects
of EM emissions and radiation. The resolution, furthermore, emphasizes to put particular attention to
electrosensitive people. People suffering from such syndromes should get special measures for
protection including wave-free zones where no wireless networks are allowed.
When it comes to planning for electrical power lines, as such that could be expected with the
introduction of ERS, it is important to plan such lines at safe distances from dwellings. The limits for
relay antennae should be reduced and follow the ALARA principles (as low as reasonably achievable)
28 VTI rapport 1053A
and all antennae should be continuously and comprehensively monitored (Parliamentary Assembly,
2011).
3.4.4. Electromagnetism in electric vehicles
3.4.4.1. Electric cars
There are numerous studies including electric cars and the effect on humans (Concha et al., 2016;
Hareuveny et al., 2015; Lin et al., 2018; Tell and Kavet, 2016). More recently Lennerz et al. (2018)
investigated whether electric cars would cause electromagnetic interference (EMI) which, in turn,
would cause dysfunction in cardiac implantable electronic devices (CIED). They found that there was
EMI but that it did not affect the CIED. Their tests did show that there were average fields of
approximately 20 µT in the back seat of 12 models of electric cars. Close to the tires they found
electric fields as high as 97 µT. These were similar to the electromagnetic fields found in trains and
trams.
Ding et al (2015) designed a homogenous adult phantom to simulate effects on human bodies from
wireless charging systems of electric vehicles. They simulated a wireless charging system based on
requirements from the industry, consisting of inductive coils and ferrite shielding. Their results
showed that the magnetic flux density within the body was 0.46 µT and the maximum value for the
electric field was 0.003V/m. These values are well below the general public limitation values set by
ICNIRP. However, as mentioned previously both the European Parliament as well as two research
organizations claims that the levels set by ICNIRP are not low enough (Carpenter and Sage, 2007;
Parliamentary Assembly, 2011; Redazione, 2015).
3.4.4.2. Trains and trams
The WHO mentioned that the electromagnetic fields are higher in trains than in trams or subways. The
electromagnetic fields vary within a train with maximum levels of 50 µT close to the floor. According
to several studies (e.g. (Halgamuge et al., 2010; WHO, 2019)) EMF of subways and trams will not
exceed the set limitations of the ICNIRP guidelines. Alternating magnetic fields will however,
according to (Hamnerius, 2012) be generated from a railway that is loaded with 50 Hz resulting in
exceeded limitations. If the railway or tram was to be powered with direct current (DC) instead it
would yield DC magnetic fields which are less harmful to human health. There is to Hamnerius’s
knowledge no evidence that DC fields would increase the risks for cancer. ERS solutions
demonstrated in Sweden today are powered with DC. The concepts are much like trams as they are
using voltage of 700-800V.
In a study by Ptitzina and Ponzetto (Ptitsyna and Ponzetto, 2012) the electromagnetic fields in electric
and hybrid cars vary during travel according to various sources within the car such as the use of air
condition. The fields are also affected of how the vehicle is driven. Higher fields of EMF were
measured during acceleration and regenerative braking. They furthermore concluded that most of the
generated magnetic fields were in the lowest frequency range of 0.001-10 Hz, hence they only showed
maximum levels of magnetic fields within this frequency range. In this range the MF was 500 μT for
trams, trains were 120 μT and electric cars were 14 μT. Electromagnetic fields of trams, trains and
electric cars were also investigated by (Halgamuge et al., 2010). Instead of looking at the maximum
levels of magnetic field strength within an average frequency range, they focused on the investigating
at which frequency the maximum levels of magnetic fields were emitted. The maximum of about 10
μT were found at 50 Hz for trams and 15.25 - 16.50 Hz for trains, while the maximum of about 5 μT
for electric or hybrid cars was found at 12 Hz.
From the comprehensive review performed by the WHO the maximum magnetic fields in trains were
50 μT, hence well below the maximum of 500 μT in the Ptitzyna and Ponzetto study. From this it
seems that even though values are well below the limits of the guidelines by ICNIRP, there could be
VTI rapport 1053A 29
peaks in different frequency fields that may be close to or above the limits. This also points to the
difficulty of comparing different studies when they did not use the same method to measure. It is
hence recommended to include some sort of standard way of measuring EMF in discussions of
standardization of ERS.
3.4.4.3. Comparing EMF of tramway and ERS
To be able to understand how EMF could affect humans it is appealing to compare the electromagnetic
fields generated in tramways with the ones generated from ERS. The size of the EMF will depend on
the electrical current coming from the electrical cable, the distance to the engine and the grounding
cable. The current will create a circuit from the power supply to the engine and back to the end of the
rail. For tramways the size of this field will be very large as the rails are used for earthing. If only
regarding the tramway the field will pass from the overhead pantograph, through the cart and down to
the earthing rail and back. For the catenary ERS solution the current from the pantograph will go from
the pantograph on top of the truck and down to the engine and back to the earthing cable also on top of
the truck. This field will be much smaller than that of the tramway cart and it will possibly not pass
through the driver cabin. In the ERS with rails this current will enter underneath of the vehicle and go
into the engine and back down again creating an even smaller field.
The expected exposure of EMF to humans will hence also depend on the size of the field and the
distance that people can be kept from it.
3.4.5. Electromagnetic fields in ERS
The EMF to be expected from ERS should be within the extremely low frequency fields, as ERS
includes electric engines as well as components such as overhead lines or rails, such that can be found
in trains or tramways. The installation of a complete ERS system will, however, include payment
solutions where some sort of wireless communication via radiofrequencies most likely will be needed.
The risks of EMF induced health issues from introducing ERS would hence come from RF as well as
ELF EMF.
Depending on type of ERS the EMF could come from either the overhead lines, the rails or the
underground induced EMF. Antennae for communication and payment systems will induce other EMF
and the vehicles themselves will induce additional EMF.
The conclusions from the WHO was that there was no evidence that exposure to low emissions of
EMF was harmful to humans. Introducing ERS is however a long-term solution and truck drivers will
be the foremost users of the ERS, at least in Sweden. The EMF shields inside the vehicles should
therefore be of extra importance.
Apart from impacts of magnetic field emissions on human health a comprehensive study of electrical
roads in England (Highways England, 2015) also mentioned impact of magnetic field emissions on
vehicle safety systems. As a safety precaution they even required suppliers to provide test information
about how their vehicles are protected against intense alternating magnetic fields.
3.4.6. Electromagnetic fields from the demonstration sites in Sweden
The eRoad Arlanda project (Berglund et al., 2018) have performed EMF measurements with
frequencies of 0-500Hz (ELF) and conclude that the measured values were below the Swedish
standard SSMFS 2008:18. The EMF in the upper part of this spectrum is, however, very close to the
set limits. When investigating for EMI (electromagnetic interference) there were also peaks that were
above the limits of EMI, which could cause disturbances in other electric devices.
As for the eHighway project on E16, there are no results from EMF and EMC measurements
available. They do, however, in their report mention that their system follows a set of international
30 VTI rapport 1053A
standards, for instance the EN 50122 and the ISO 6469-3 which considers the safety of people when it
comes to avoiding electric chocks from road and rail vehicles and the standards EN 50293 or DIN EN
50293 regarding electromagnetic compatibility of traffic signs and signalling systems such as
Intelligent transportation systems (ITS). There is nothing regarding EMF and the limits that are set for
human health reasons covered in the Swedish standard SSMFS 2008:18.
As described previously there are organizations that are prompting for stricter regulations for EMF
limits and the same signals seem to come from the EU parliament as well (Carpenter and Sage, 2007;
European Parliament, 2013; Redazione, 2015). Hence, to leave it at keeping EMF levels of the ERS
techniques right below recommended levels, that already seem to be too high, could be a costly matter
in the end.
3.5. EMC
Electromagnetic compatibility, EMC is the concept that makes sure that electronics or electrical
devices can operate in close proximity to each other without interfering. Basically, the EMC makes
sure that the electromagnetic environment is not affected in such a way that it would impact the
functionality of other devices. There are EMC standards and methods to make sure that all electronic
devices are within standard emission limits (Electronics-notes.com, 2019), meaning that they do not
emit more electromagnetic radiation than set limits.
The International Committee on Radio Frequency Interference (CISPR) has set the limits for EMC
standards, hence those limits are foremost set to protect radio frequencies. Other electromagnetic
interferences are however also discussed in the subcommittees of CISPR.
To be able to develop a device or technology that should function in such environment where the
emissions follow standards for radio frequencies it will be necessary to have some sort of inbuilt
immunity within the device to make the radio transmitters less vulnerable to EMC-emissions. Other
means of protection from unwanted electromagnetic signals such as EMI (electromagnetic
interference) is to use EMI-shields often composed from carbon composites (Chung, 2001). It is,
however, important to mention that such shields are often the last way out and often tend to be a very
costly solution. The most cost-efficient way is to consider EMC emissions in the development stage
and thereby produce products with good circuit designs.
3.5.1. EMC in ERS
Each type of ERS technology would of course also need to follow the EMC standards but there could
be unforeseen signals from the use of such a large-scale system, the size of the railway system. When
it comes to standards, it is important to analyze the standard in terms of what it originally was intended
to be used for. Take for instance the example of optimizers for solar panels. They use the generic EMC
standard for CE-marking but since the standard does not include DC (Direct Current) the optimizers
might not fulfill the requirements in the standard. Other examples come from the use of several
devices in a module where each device would reach the requirement on their own but when put
together, the emissions would exceed the limits of the standard requirements.
In the railway systems there have been reports of disturbances when trains for some reason have to put
in extra effort, in for instance up a hillslope (Morant et al., 2012), along rails that are damaged etc.
Studies on trains have shown that such interference could cause the signalling system to malfunction
and in worst case cause collision.
In regards of the ERS rail solution these effects might appear and could affect the ERS in such a way
that communication between the vehicle and the road could be malfunctioning, ending up in no
transfer of energy or identification of the vehicle etc.
VTI rapport 1053A 31
Unforeseen signals could occur during arching or possibly in the on or off connection with the
conductive solutions. There is, however, a lack of knowledge in these aspects of the ERS since the
concept of ERS is new and none of the ERS technologies has yet been tested in full scale. Further
research is needed to understand where and how unwanted signals could appear as well as how they
might interfere with other vehicles or equipment along the roads.
According to Morant et al (2012), electromagnetic disturbance stands for about 70% of all failures in
the railway system. There could hence be an increased risk of malfunctioning information systems
also within ERS, hence inventories regarding crucial information services along ERS potential roads
are needed to understand how and what effect EMC emissions could have on the road safety.
3.5.2. EMI tests of ERS
Lindgren (Lindgren, 2015) tested EMI on one conductive ERS technique and found that EMI
emissions would fulfill the requirements of EN 50121-2, but are just on the limits for fulfilling the
CISPR 12. They could not find any alarming EMI levels below 10 MHz.
They also tested ERS short circuit through a tire and found that short circuit would only damage the
tire locally unless it generated a fire inside of the pressurized tire. They, furthermore, suggested that if
the tire was filled with flammable substances from canned tire inflators there could be risks for
hazardous situations. Such effects could not be safely tested in their laboratory but should be further
investigated in terms of large-scale implementations of ERS.
Kanz et al. (Kanz et al., 2004) found that some of the advisory system models of automated external
defibrillators (AED) often found in public places, such as for instance train stations, are vulnerable to
EMI, especially that generated from electric cables with 15 kV and 16 2/3 Hz AC. These advisory
systems are crucial as they give simple audio and visual commands to help the person that uses it. The
interference is however, minimized if the person in need of defibrillator is positioned parallel to the
overhead line, and the electrode cables are perpendicular to the overhead line.
For the case of ERS, the power in the overhead cables will not be more than 800V and use DC rather
than AC, hence the interference might not be a question for concern. It is, however, important to
consider and be aware of the risks. There could be a need for further investigations regarding such
interference with other important electrical devices.
32 VTI rapport 1053A
4. ERS and the impact on the landscape and nature
The landscape is an important part of our perception of our environment and nature. In large
infrastructure projects, the assessment of the landscape may hence be included already in the planning
phase of the project.
The comprehensive method used in Sweden analyses many different aspects and includes background
information studies, map studies, interviews and field visits. The landscape is characterized in terms of
landforms, topography, reliefs, geological direction, rock types, soil types and hydrology. The spatial
context is also considered where the openness of the landscape is included as well as types and density
of vegetation. Additionally, land use parameters are included and current infrastructure, movement
patterns and functional connections. It is important to consider significant landmarks, the history of the
area and to register and contemplate about effects on ecosystems. One important part of this is to
consider people’s connection with the use of the landscape for instance significant ecosystem services
and cultural references such as places known from literature. A comprehensive method description is
found in (Noborn et al., 2018).
Since the ERS are supposed to be implemented on already existing roads the assessment of the
landscape will possibly only be important for the case of the catenary/overhead technology. The large
support masts, that are installed about every 50 meters, and their connected wiring, are posing a huge
impact on the perception of the landscape both at a distance as well as when driving underneath them.
Figure 3. Driving along the E16 close to Sandviken, Sweden. Photo: Lina Nordin.
According the STA document that regulates how streets and roads should be designed and constructed
(STA, 2015) it is important to keep the landscape intact. This means both in terms of visual
fragmentation of the landscape but also regarding hydrological aspects. In the case with the overhead
catenary technology, as the one shown in figure 3, there will be a visual fragmentation especially in
open areas. The cables could also pose risks for bats and birds as described in section 4.4.2.
The catenary solution could also pose a safety risk on particular road stretches, where a curvature of
the road could disturb the free view of the road (Figure 4).
VTI rapport 1053A 33
Figure 4. Potential safety risk as the direct view of the driver could be obstructed. Photo: Lina Nordin.
This is also important to consider during the planning phase of where to install the support masts of
this type of technology.
The implementation of ERS will, regardless of technology, need to claim extra land for service areas,
wiring and drainage, switchyard, transformer stations etc. To understand how much extra land that is
needed, a Geographical information system (GIS) could be used. A preliminary study was done by
two students from the University of Gothenburg (Johnsson and Strömberg, 2019). They made a GIS
model for comparing the suitability of different road stretches in terms of implementing ERS with the
catenary technology as well as with the rail technology. The study was preliminary and further
developments are needed to be able to use the model for the purpose of truly comparing between
different technologies or areas.
Strömberg and Johnsson included a distance calculation to the nearest road from the ERS road.
Parallel roads or adjacent roads could be used for maintenance personnel if the technology for some
reason would need extra service. If the model was to include information about landownership, it
should be possible to estimate how much extra land the STA will have to claim, in order to realize a
full-scale deployment of ERS.
4.1. How much extra land will be needed?
The Swedish national roads are run under the administration of the STA. The STA and their
contractors are responsible and have the right to use the land that includes the road and road area as
well as an additional two meters. In areas with safety zones the additional area can be extended up to
14 meters. In areas where the STA does not have safety zones such extra land will have to be
expropriated according to the law of expropriation with 25% of the market value of the property
(Swedish Transport Administration, 2012).
34 VTI rapport 1053A
The road area is defined as the road, the side verge, both slopes of the adjacent ditch and, if present,
the hard edge on the other side of the ditch. Ducts, pipes and wiring put in the road direction needs to
be placed in the slope foot or the outer slope of the ditch. If placed at the bottom of a ditch, the wiring
needs to be laid at a depth of least 0.55 m (Zetterberg, 2017). Zetterberg also mentions that wiring
cabinets, switchyard and transformer stations should be placed outside of the road area.
It is therefore possible for the STA to use the extra two meters outside of the road area to place such
equipment like wiring cabinets and transformer stations. The question is whether these constructions
are that small. The transformer stations of the ERS project along E16 in Sweden were at least 2,5
meters wide. With the current design of the building it would not fit within the extra two meters of a
regular roadside area. However, if the ERS would be installed along a road with safety zones, which is
most likely, this will possibly not pose any extra expropriation. This is however an important
parameter to considering when planning for placement of ERS road stretches.
The switchboxes (switchyards) and wiring cabinets of the rail solutions will most likely fit into the
additional 2 meters.
VTI rapport 1053A 35
5. Discussion and conclusion
The discussions are divided into the different types of environmental impact or effects analysed with a
summarizing concluding remark at the end of the section.
5.1. Energy and use of resources
The basic concept of ERS is to supply energy to vehicles. In doing so there will be need for good
conductors as well as good isolators and shields. The materials that are used in the various ERS
technologies will hence need to have the same kind of characteristics and will most likely be the same
in each of the ERS concepts. It will instead be the amount of materials used, as well as the wear and
tear of the components of the system, that will be important to consider when comparing between ERS
concepts.
This project set out to investigate environmental aspects of ERS, but the amount and types of materials
used in each separate ERS concept is needed to be able to come to a fair conclusion regarding the
differences between them. It is common to use life cycle assessment (LCA) methods in comparing
between concepts. Such methods are very comprehensive and investigates the environmental impact
that each product or concept will have from the production of the materials used in the concept to the
use and maintenance of the concept and finally the end-of-life phase. There are a few LCA studies
performed on ERS, but since the concepts are so new to the market it is difficult to get a good analysis
regarding energy use of everyday maintenance as well as wear of the materials during a full
deployment of the concept.
It was furthermore difficult to retrieve information from the demonstration projects as both are
continuously developing and improving their respective technologies, hence, the difficulty of getting a
good comparison of the concepts.
5.2. Emissions of air pollutants (PM2,5 and PM10)
Electric road technologies contribute to emissions of PM10 particles in three different ways 1) the
contact between the electric current collector and the conductor, 2) brakes and other moving parts, 3)
tires and road surface.
The pantograph and wire are worn from vehicles using the system and small particles mainly from
iron are emitted. From studies on railway and in subways it is shown that the largest concentrations of
particulate matter are found in closed areas such as in subways or in train stations. This implicates that
the effects might not be substantial in open rural areas where the air is circulated.
Particulate matter coming from the contact between the current collector and the in-road rail is
unknown and measurements are required.
An obvious difference from conventional roads and vehicles is that there are no exhaust particles from
the combustion in electric vehicles. The effects on the particle emissions (PM10 and PM 2.5) are
however unclear as the successively improved particle filters used in cars in recent years have reduced
the exhaust related particles from conventional vehicles. Measurements are needed to be able to
compare particles from combustion motor vehicles and electric vehicles in the same road environment.
Particulate emission from brakes, tyres, and road surfaces of ERS correlates with the weight of the
vehicles and are therefore thought to be similar to conventional combustion vehicles.
Emissions of particles will depend on the characteristics of the materials used. If materials are more
prone to wear and tear more particles could form. It is difficult to compare between different ERS
concepts when there is little information about the materials used. Measurements are needed to fully
understand what type and how much particles are to be expected. This can be done on the test sites
under similar test procedures.
36 VTI rapport 1053A
One important part to consider when comparing different conductive technologies are the distribution
of the particles to the ambient environment. Will particles from the overhead catenary solution be
more widespread due to wind dispersion? Or will turbulence from passing vehicles be the most crucial
part in spreading particles to the environment?
Either way, all emissions from combustion engines, both greenhouse gases and particles will be
reduced with the introduction of ERS. The inductive technology will however not create any airborne
particles other than what comes from the regular wear and tear of tyres and the road.
5.3. Noise
Generally, when discussing noise issues and electrical vehicles the noises are reduced at velocities up
to 50 km/h. At higher speeds, the noise from the interaction between tyres and the road will drown out
the noise of the engine, hence there will be no difference between combustion engines and electrical
engines at speeds over 50 km/h.
For conductive ERS, there will be occasions where arcing appears. Arcing is the lightening sensation
when the contact between the current collector and the power supply cable or rail is interrupted. Such
arcing will make a loud noise, depending on the strength of the electrical charge.
It is difficult to know how often such arcing will occur and hence how often such noise will be
apparent.
Noises from the interaction of the sliding contact between the current collector and the cable or rail is
also difficult to estimate. Some measurements have been made within each demonstration project, but
the methods used are not comparable with each other and should be done by some independent party.
When it comes to the work environment of truck drivers it is also important to consider the noises
within the cabin of their truck. It is however apparent from discussions with the test drivers of
eHighway in Gävle that the noises are reduced within the cabin when the truck is connected to the
ERS. The driver also mentioned that there is an apparent reduction in vibrations when driving on
electricity as compared to when the combustion engine is used.
Again, the noise should be even more reduced if using the inductive concept of ERS since there will
be no sliding of current collectors. It is, however, important to remember that transverse joints from
connecting cables, used for the in-road technologies, could cause thumping noise emissions to the
surrounding environment when vehicles are driving over them.
5.4. EMF
The emissions of EMF will differ between the different concepts depending on how much power that
is put into the system. However, each technology is constantly improving and the differences between
these systems in terms of EMF emissions could in the end be insignificant. The risks of interfering
with other equipment is however increased if there are unexpected emissions of EMF from the system.
Such unexpected emissions could for instance be those from arcing. Arcing will apart from increasing
the wear of the wire and carbon strips, also cause EMF that could reach much higher frequencies than
what is expected during standard operation. Arcing will only occur in conductive technologies, with an
increase in winter during temperatures below zero. Hence the risks of having unexpected EMF
emissions are greater for the conductive technologies.
The distance from the source is furthermore important when discussing EMF. This will be different
between the different concepts. The electrical fields are always present within the electric parts such as
cables etc. Humans can be protected from such fields by shielding materials, such as walls, trees or
soil. Cables that are put in the ground will hence not emit as strong fields as would overhead cables.
VTI rapport 1053A 37
It is, however, unclear as to whether inductive technologies will be different since it depends on
sending electrical charges from beneath the road surface. Further investigations are needed. Preferably
done in the same manner between all different ERS test-sites, to be able to compare between different
concepts.
When preparing for implementing ERS it is hence of importance to consider different kinds of
shielding for people living close to the electric road or to plan for ERS at safe distances from
dwellings. As described by the European Parliamentary Assembly, the present limits for relay
antennae should be reduced and follow the ALARA principles (as low as reasonably achievable) and
all antennae should be continuously and comprehensively monitored (Parliamentary Assembly, 2011).
The vehicles themselves should be constructed in such a way that drivers are shielded from EMF. It is
however difficult to shield magnetic fields as they will only diminish with distance from the source.
When the vehicles are not connected to the road there will not be any magnetic fields, hence people
living nearby will only be affected if someone is charging their vehicles from the ERS.
To be able to communicate with the vehicles and power systems as well as business models included
in the ERS the need for WIFI or mobile communication will be evident. It seems, however, as if plants
are more susceptible to EMF induced from WIFI. Migrating animals and insects, bats, birds and fish
are furthermore affected by EMF and special investigations and precautions are therefore needed to
understand and eliminate the risks of EMF from the whole electric roads system including WIFI
communication.
It will be important to investigate and analyze EMC standards which are to be used in ERS as there are
risks when trying to use existing standards without considering the system, which the standard was
originally intended to be used for.
There is furthermore a lack of standards optimized for the inductive ERS technologies. If standards
that are intended for conductive transfer is used instead, the inductive ERS could uphold the standard
but might not reach the requirements at system level. It is furthermore important to consider such
issues early in the development stage to limit the risks of increased costs if it e.g. later turns out that
EMI shielding would be needed.
5.5. Comparison between different ERS technologies
To compare the impact on emissions of particulate matter that each respective ERS concept could
have, the occurrence of various aspects is estimated in table 2, where white is no or little impact/risk,
and grey is high impact/risk.
Table 2. Impact assessment of various aspects affecting emissions.
Aspect that could lead to increased emissions
Conductive Catenary
Conductive rail on road
Conductive rail in road
Inductive ICE V Battery EV Heavy duty
Weight of vehicle
Batteries + Pick-up: 1000kg more than Hybrid truck.*
Battery: 600kg+ Pick-up: 70 kg
Battery: 600 kg Pick-up and electric system: 1000 kg**
Battery: 600 kg Pick-up: No information
Engine, transmission, fuel system and exhaust hardware: 3000kg.
100 – 300 kWh Battery: 1250kg – 6100kg***
Contact wear from tyres and road surface Non metal particles
Less than ICE V
Less than ICE V
Less than ICE V
Less than ICE V
Yes Yes - Increased wear from the heavier vehicles.
38 VTI rapport 1053A
Aspect that could lead to increased emissions
Conductive Catenary
Conductive rail on road
Conductive rail in road
Inductive ICE V Battery EV Heavy duty
Contact wear of brakes and other moving parts Metal particles
Lower during engine brakes and regenerative braking
Lower during engine brakes and regenerative braking
Lower during engine brakes and regenerative braking
Lower during engine brakes and regenerative braking dependent on weight
Yes Lower during engine brakes and regenerative braking dependent on weight
Current collector and wire Metal particles
Yes Yes Yes No No No
Particles from combustion and tailpipe
No No No No Yes No
* (Region Gävleborg, 2015) ** (eRoadArlanda, 2017) *** (Earl et al., 2018) + ERS Vehicle Batteries are assumed to weigh 600 kg, same as the truck used in the eRoad Arlanda project, where no other information was found.
VTI rapport 1053A 39
Referenser
Areskoug, H., Alesand, T., Hedberg, E., Johansson, C., 2001. Kartläggning av inandningsbara
partiklar i svenska tätorter och identifikation av de viktigaste källorna 36.
Asplund, G., 2017. Email about installation of electric road eRoadArlanda.
Bahaodini, A., Owjfard, M., Tamadon, A., Jafari, S.M., 2015. Low frequency electromagnetic fields
long-term exposure effects on testicular histology, sperm quality and testosterone levels of
male rats. Asian Pacific Journal of Reproduction 4, 195–200.
https://doi.org/10.1016/j.apjr.2015.06.001
Balieu, R., Chen, F., Kringos, N., 2019. Life cycle sustainability assessment of electrified road
systems. Road Materials and Pavement Design 20, S19–S33.
https://doi.org/10.1080/14680629.2019.1588771
Belova, N.A., Acosta-Avalos, D., 2015. The Effect of Extremely Low Frequency Alternating
Magnetic Field on the Behavior of Animals in the Presence of the Geomagnetic Field. Journal
of Biophysics 2015, 1–8. https://doi.org/10.1155/2015/423838
Berglund, B., Hörnfeldt, S., Granzell, N., Asplund, G., Dahlström, H., Wrede, F., Hellgren, M.,
Honeth, N., 2018. eRoad Arlanda - Sammanfattning av erfarenheter hittills (No. L1.9).
Bi, Z., Kan, T., Mi, C.C., Zhang, Y., Zhao, Z., Keoleian, G.A., 2016. A review of wireless power
transfer for electric vehicles: Prospects to enhance sustainable mobility. Applied Energy 179,
413–425. https://doi.org/10.1016/j.apenergy.2016.07.003
Carpenter, D.O., Sage, C., 2007. Bioinitiative Report 2012, Key Sientific Evidence and Public Health
Policy Recommendations.
Chen, F., 2016. Sustainable Implementation of Electrified Roads : Structural and Material Analyses.
Chung, D.D.L., 2001. Electromagnetic interference shielding effectiveness of carbon materials.
Carbon 39, 279–285. https://doi.org/10.1016/S0008-6223(00)00184-6
Concha, P.M.-T., Velez, P., Lafoz, M., Arribas, J.R., 2016. Passenger Exposure to Magnetic Fields
due to the Batteries of an Electric Vehicle. IEEE Transactions on Vehicular Technology 65,
4564–4571. https://doi.org/10.1109/TVT.2015.2490105
Denby, B.R., Kupiainen, K.J., Gustafsson, M., 2018. Chapter 9 - Review of Road Dust Emissions, in:
Amato, F. (Ed.), Non-Exhaust Emissions. Academic Press, pp. 183–203.
https://doi.org/10.1016/B978-0-12-811770-5.00009-1
Denby, B.R., Sundvor, I., Johansson, C., Pirjola, L., Ketzel, M., Norman, M., Kupiainen, K.,
Gustafsson, M., Blomqvist, G., Kauhaniemi, M., Omstedt, G., 2013a. A coupled road dust and
surface moisture model to predict non-exhaust road traffic induced particle emissions
(NORTRIP). Part 2: Surface moisture and salt impact modelling. Atmospheric Environment
81, 485–503. https://doi.org/10.1016/j.atmosenv.2013.09.003
Denby, B.R., Sundvor, I., Johansson, C., Pirjola, L., Ketzel, M., Norman, M., Kupiainen, K.,
Gustafsson, M., Blomqvist, G., Omstedt, G., 2013b. A coupled road dust and surface moisture
model to predict non-exhaust road traffic induced particle emissions (NORTRIP). Part 1: Road
dust loading and suspension modelling. Atmospheric Environment 77, 283–300.
https://doi.org/10.1016/j.atmosenv.2013.04.069
Ding, P.-P., Pichon, L., Bernard, L., Razek, A., 2015. Electromagnetic fields in body by wireless
inductive system. COMPEL: The International Journal for Computation and Mathematics in
Electrical and Electronic Engineering. https://doi.org/10.1108/COMPEL-08-2014-0211
Earl, T., Mathieu, L., Cornelis, S., Kenny, S., Ambel, C.C., Nix, J., 2018. Analysis of long haul battery
electric trucks in EU 22.
40 VTI rapport 1053A
eHighways, 2018. Elvägar - klimatsmarta och kostnadseffektiva transporter [WWW Document]. URL
https://w3.siemens.se/home/se/sv/Mobility/interurban_mobility/road_solutions/elvagar-
klimatsmarta-och-kostnadseffektiva-transporter/Pages/elvagar-klimatsmarta-och-
kostnadseffektiva-transporter.aspx?istablet=true (accessed 7.9.18).
Electronics-notes.com, 2019. What is EMC | ElectroMagnetic Compatibility | Electronics Notes
[WWW Document]. URL https://www.electronics-notes.com/articles/analogue_circuits/emc-
emi-electromagnetic-interference-compatibility/what-is-emc-basics-tutorial.php (accessed
8.15.19).
Elways, 2018. Välkommen till Elways - Från Sverige till Spanien utan stopp för laddning eller
tankning. [WWW Document]. URL http://elways.se
EMFscientist, 2019. EMFscientist.org - International EMF Scientist Appeal [WWW Document]. URL
https://emfscientist.org/index.php/emf-scientist-appeal (accessed 8.13.19).
eRoadArlanda, 2018. Elvägar – en hållbar transportlösning för framtiden - eRoadArlanda [WWW
Document]. URL https://eroadarlanda.se/.
eRoadArlanda, 2017. Sveriges första eldrivna lastbil för elväg är här. eRoadArlanda. URL
https://eroadarlanda.se/sveriges-forsta-eldrivna-lastbil-for-elvag-ar-har/ (accessed 11.20.19).
European Council, 2008. Directive 2008/50/EC of the European Parliament and of the Council of
21 May 2008 on ambient air quality and cleaner air for Europe, 152.
European Council, 1996. COUNCIL DIRECTIVE 96/62/EC of 27 September 1996 on ambient air
quality assessment and management.
European Parliament, 2013. Directive 2013/35/EU of the European Parliament and of the Council of
26 June 2013 on the minimum health and safety requirements regarding the exposure of
workers to the risks arising from physical agents (electromagnetic fields) (20th individual
Directive within the meaning of Article 16(1) of Directive 89/391/EEC) and repealing
Directive 2004/40/EC, 179.
Favre, D., 2017. Disturbing honeybees’ behavior with electromagnetic waves: a methodology 5.
Finne, P., Fryd, J., 2017. Støjer dilatationsfuger? TRAFIK & VEJE 2017 AUGUST, 62–65.
Fisher, T.M., Farley, K.B., Gao, Y., Bai, H., Tse, Z.T.H., 2014. Electric vehicle wireless charging
technology: a state-of-the-art review of magnetic coupling systems. Wireless Power Transfer
1, 87–96. https://doi.org/10.1017/wpt.2014.8
Genell, A., Västfjäll, D., 2013. Experience and information content affect interior vehicle sound
quality assessments. IJVNV 9, 47. https://doi.org/10.1504/IJVNV.2013.053816
Gil, A., Taiber, J., 2014. A Literature Review in Dynamic Wireless Power Transfer for Electric
Vehicles: Technology and Infrastructure Integration Challenges, in: Wellnitz, J., Subic, A.,
Trufin, R. (Eds.), Sustainable Automotive Technologies 2013, Lecture Notes in Mobility.
Springer International Publishing, pp. 289–298.
Gon, H.A.C.D. van der, Gerlofs-Nijland, M.E., Gehrig, R., Gustafsson, M., Janssen, N., Harrison,
R.M., Hulskotte, J., Johansson, C., Jozwicka, M., Keuken, M., Krijgsheld, K., Ntziachristos,
L., Riediker, M., Cassee, F.R., 2013. The Policy Relevance of Wear Emissions from Road
Transport, Now and in the Future—An International Workshop Report and Consensus
Statement. Journal of the Air & Waste Management Association 63, 136–149.
https://doi.org/10.1080/10962247.2012.741055
Gustafsson, M., Blomqvist, G., Dahl, A., Gudmundsson, A., Ljungman, A., Lindbom, J., Rudell, B.,
Swietlicki, E., 2005. Inandningsbara partiklar från interaktion mellan däck, vägbana och
friktionsmaterial : slutrapport av WearTox-projektet. VTI., VTI rapport 520.
Gustafsson, M., Blomqvist, G., Franzen, L., Rudell, B., 2003. Föroreningsnedfall från järnvägstrafik
(No. VTI meddelande 947). VTI, Linköping.
VTI rapport 1053A 41
Halgamuge, M.N., 2017. Review: Weak radiofrequency radiation exposure from mobile phone
radiation on plants. Electromagn Biol Med 36, 213–235.
https://doi.org/10.1080/15368378.2016.1220389
Halgamuge, M.N., Abeyrathne, C.D., Mendis, P., 2010. Measurement and analysis of electromagnetic
fields from trams, trains and hybrid cars. Radiat Prot Dosimetry 141, 255–268.
https://doi.org/10.1093/rpd/ncq168
Hamnerius, Y., 2012. Elektriska och magnetiska fält från spårvägstrafik (No. 2012:03), Spårvagnar i
Skåne. Spårvagnar i Skåne.
Hann, S., Sherrington, C., Jamieson, O., Hickman, M., Kershaw, P., Bapasola, A., Cole, G., 2018.
Investigating options for reducing releases in the aquatic environment of microplastics emitted
by (but not intentionally added in) products Final Report. Report for DG Environment of the
European Commission 335.
Hareuveny, R., Sudan, M., Halgamuge, M.N., Yaffe, Y., Tzabari, Y., Namir, D., Kheifets, L., 2015.
Characterization of Extremely Low Frequency Magnetic Fields from Diesel, Gasoline and
Hybrid Cars under Controlled Conditions. International Journal of Environmental Research
and Public Health 12, 1651–1666. https://doi.org/10.3390/ijerph120201651
Havas, M., Sheena Symington, M., 2016. Effects of Wi-Fi Radiation on Germination and Growth of
Broccoli, Pea, Red Clover and Garden Cress Seedlings: A Partial Replication Study. CCB 10,
65–73. https://doi.org/10.2174/2212796810666160419161000
Highways England, 2015. Feasibility study: Powering electric vehicles on England’s major roads.
Transport Research Laboratory.
Hörnfeldt, S., 2018. Communication with maintenance coordinator NCC regarding eRoads Arlanda.
Ihs, A., 2010. Trafikanternas krav på vägars tillstånd (No. VTI rapport 702). VTI.
Iversen, L.M., Stahlfest Holck Skov, R., 2015. Measurement of noise from electrical vehicles and
internal combustion engine vehicles under urban driving conditions. Presented at the
EuroNoise, 2015, Maastricht, p. 6.
Jan Nylander, 2018. Project ELVÄG – E16, DELRAPPORT 8P. Region Gävleborg.
Johansson, C., Norman, M., Gustafsson, M., 2008. Genomsnittliga emissionsfaktorer för PM10 i
Stockholmsregionen som funktion av dubbdäcksandel och fordonshastighet (No. SLB-rapport
2:2008).
Johnsson, A., Strömberg, J., 2019. Elektrifiera Sveriges motorvägar? - En GIS-analys över
möjligheten att installera elvägssystem längs med två svenska motorvägar (Bachelor Thesis).
Gothenburg University, Gothenburg.
Kanz, K.-G., Kay, M.V., Biberthaler, P., Russ, W., Wessel, S., Lackner, C.K., Mutschler, W., 2004.
Susceptibility of automated external defibrillators to train overhead lines and metro third rails.
Resuscitation 62, 189–198. https://doi.org/10.1016/j.resuscitation.2004.02.018
Karimi, S.A., Salehi, I., Shykhi, T., Zare, S., Komaki, A., 2019. Effects of exposure to extremely low-
frequency electromagnetic fields on spatial and passive avoidance learning and memory,
anxiety-like behavior and oxidative stress in male rats. Behavioural Brain Research 359, 630–
638. https://doi.org/10.1016/j.bbr.2018.10.002
Karlsson, H.L., Ljungman, A.G., Lindbom, J., Möller, L., 2006. Comparison of genotoxic and
inflammatory effects of particles generated by wood combustion, a road simulator and
collected from street and subway. Toxicol. Lett. 165, 203–211.
https://doi.org/10.1016/j.toxlet.2006.04.003
Karlsson, H.L., Nilsson, L., Möller, L., 2005. Subway particles are more genotoxic than street
particles and induce oxidative stress in cultured human lung cells. Chem. Res. Toxicol. 18,
19–23. https://doi.org/10.1021/tx049723c
42 VTI rapport 1053A
Kole, P.J., Löhr, A.J., Van Belleghem, F.G.A.J., Ragas, A.M.J., 2017. Wear and Tear of Tyres: A
Stealthy Source of Microplastics in the Environment. International Journal of Environmental
Research and Public Health 14, 1265. https://doi.org/10.3390/ijerph14101265
Kupiainen, K., Ritola, R., Stojiljkovic, A., Pirjola, L., Malinen, A., Niemi, J., 2016. Contribution of
mineral dust sources to street side ambient and suspension PM10 samples. Atmospheric
Environment 147, 178–189. https://doi.org/10.1016/j.atmosenv.2016.09.059
Lai, J., Zhang, Y., Liu, X., Zhang, J., Ruan, G., Chaugai, S., Chen, C., Wang, D.W., 2016. Effects of
extremely low frequency electromagnetic fields (100μT) on behaviors in rats.
NeuroToxicology 52, 104–113. https://doi.org/10.1016/j.neuro.2015.11.010
Larsson, B.M., 2008. Inducerar exponering av friska försökspersoner i tunnelbanemiljö akuta
luftvägseffekter? Presented at the Transportforum 2008, Linköping, Sweden 9-10 januari,
Linköping.
Laszlo, A.M., Ladanyi, M., Boda, K., Csicsman, J., Bari, F., Serester, A., Molnar, Z., Sepp, K., Galfi,
M., Radacs, M., 2018. Effects of extremely low frequency electromagnetic fields on turkeys.
Poultry Science 97, 634–642. https://doi.org/10.3382/ps/pex304
Lennerz, C., O’Connor, M., Horlbeck, L., Michel, J., Weigand, S., Grebmer, C., Blazek, P., Brkic, A.,
Semmler, V., Haller, B., Reents, T., Hessling, G., Deisenhofer, I., Whittaker, P., Lienkamp,
M., Kolb, C., 2018. Electric Cars and Electromagnetic Interference With Cardiac Implantable
Electronic Devices: A Cross-sectional Evaluation. Ann Intern Med 169, 350.
https://doi.org/10.7326/M17-2930
Lerchl, A., Klose, M., Grote, K., Wilhelm, A.F.X., Spathmann, O., Fiedler, T., Streckert, J., Hansen,
V., Clemens, M., 2015. Tumor promotion by exposure to radiofrequency electromagnetic
fields below exposure limits for humans. Biochem. Biophys. Res. Commun. 459, 585–590.
https://doi.org/10.1016/j.bbrc.2015.02.151
Lin, J., Lu, M., Wu, Tong, Yang, L., Wu, Tongning, 2018. EVALUATING EXTREMELY LOW
FREQUENCY MAGNETIC FIELDS IN THE REAR SEATS OF THE ELECTRIC
VEHICLES. Radiat Prot Dosimetry 182, 190–199. https://doi.org/10.1093/rpd/ncy048
Lindbom, J., Gustafsson, M., Blomqvist, G., Dahl, A., Gudmundsson, A., Swietlicki, E., Ljungman,
A.G., 2006. Exposure to Wear Particles Generated from Studded Tires and Pavement Induces
Inflammatory Cytokine Release from Human Macrophages. Chem. Res. Toxicol. 19, 521–
530. https://doi.org/10.1021/tx0503101
Lindgren, L., 2015. EMC and Safety Studies on Electric Road Systems. Swedish Hybrid Vehicle
Centre.
Lu, F., Zhang, H., Mi, C., 2017. A Review on the Recent Development of Capacitive Wireless Power
Transfer Technology. Energies 10, 1752. https://doi.org/10.3390/en10111752
Martínez-Sámano, J., Flores-Poblano, A., Verdugo-Díaz, L., Juárez-Oropeza, M.A., Torres-Durán,
P.V., 2018. Extremely low frequency electromagnetic field exposure and restraint stress
induce changes on the brain lipid profile of Wistar rats. BMC Neurosci 19, 31.
https://doi.org/10.1186/s12868-018-0432-1
Matthes, R., Bernhardt, J.H. (Eds.), 1999. Guidelines on limiting exposure to non-ionizing radiation: a
reference book based on the guidelines on limiting exposure to non-ionizing radiation and
statements on special applications, ICNIRP. International Commission on Non-Ionizing
Radiation Protection, Oberschleißheim.
Morant, A., Wisten, A., Galar, D., Kumar, U., Niska, S., 2012. Railway EMI impact on train operation
and environment, in: International Symposium on Electromagnetic Compatibility - EMC
EUROPE. Presented at the 2012 International Symposium on Electromagnetic Compatibility -
EMC EUROPE, IEEE, Rome, Italy, pp. 1–7.
https://doi.org/10.1109/EMCEurope.2012.6396847
VTI rapport 1053A 43
NCC, 2014. NCC och Elways finslipar på detaljerna. http://se-
old.web04.ncc.episerverhosting.com/om-ncc/ncc-i-sverige/ncc-roads/roads-senaste-nytt/ncc-
och-elways-finslipar-pa-detaljerna/ [WWW Document]. URL http://se-
old.web04.ncc.episerverhosting.com/om-ncc/ncc-i-sverige/ncc-roads/roads-senaste-nytt/ncc-
och-elways-finslipar-pa-detaljerna/ (accessed 7.24.17).
Noborn, T., Schibbye, B., Wade, E., Björckebaum, M., Lanemo, E., Askling, J., Kindvall, O., 2018.
Landscape as an arena - Integrated landscape character assessment - Method description.
Ögren, M., Molnár, P., Barregard, L., 2018. Road traffic noise abatement scenarios in Gothenburg
2015 – 2035. Environmental Research 2018, 516–521.
https://doi.org/10.1016/j.envres.2018.03.011
Pall, M.L., 2018. Wi-Fi is an important threat to human health. Environmental Research 164, 405–
416. https://doi.org/10.1016/j.envres.2018.01.035
Pall, M.L., 2016. Electromagnetic Fields Act Similarly in Plants as in Animals: Probable Activation of
Calcium Channels via Their Voltage Sensor [WWW Document]. Current Chemical Biology.
URL http://www.eurekaselect.com/141390/article (accessed 8.15.19).
Panko, J., Kreider, M., Unice, K., 2018. Chapter 7 - Review of Tire Wear Emissions: A Review of
Tire Emission Measurement Studies: Identification of Gaps and Future Needs, in: Amato, F.
(Ed.), Non-Exhaust Emissions. Academic Press, pp. 147–160. https://doi.org/10.1016/B978-0-
12-811770-5.00007-8
Parliamentary Assembly, 2011. PACE - Resolution 1815 (2011) - The potential dangers of
electromagnetic fields and their effect on the environment.
Ptitsyna, N., Ponzetto, A., 2012. Magnetic fields encountered in electric transport: Rail systems,
trolleybus and cars, in: International Symposium on Electromagnetic Compatibility - EMC
EUROPE. Presented at the 2012 International Symposium on Electromagnetic Compatibility -
EMC EUROPE, IEEE, Rome, Italy, pp. 1–5.
https://doi.org/10.1109/EMCEurope.2012.6396901
Redazione, L., 2015. International Appeal: Scientists call for protection from non-ionizing
electromagnetic field exposure. 1 20, 180–182.
Regeringskansliet, 2017. Uppdrag att utreda förutsättningarna för att elvägar på sikt ska kunna vara en
del av det svenska transportsystemet [WWW Document]. Regeringskansliet.
https://www.regeringen.se/regeringsuppdrag/2017/10/uppdrag-att-utreda-forutsattningarna-
for-att-elvagar-pa-sikt-ska-kunna-vara-en-del-av-det-svenska-transportsystemet/
Region Gävleborg, 2015. Elväg-Gävle, Slutrapport Fas 2 - Bilaga 2-1 Systembeskrivning.
Rubin, G.J., Munshi, J.D., Wessely, S., 2005. Electromagnetic Hypersensitivity: A Systematic Review
of Provocation Studies. Psychosomatic Medicine 67, 224.
https://doi.org/10.1097/01.psy.0000155664.13300.64
Sandberg, U., Ejsmont, J.A., 2002. Tyre/Road Noise Reference Book.
Schulte, J., Ny, H., 2018. Electric Road Systems: Strategic Stepping Stone on the Way towards
Sustainable Freight Transport? Sustainability 10, 1148. https://doi.org/10.3390/su10041148
Sen. Kerry, J.F., 2010. S.841 - Pedestrian Safety Enhancement Act of 2010 [WWW Document]. URL
https://www.congress.gov/bill/111th-congress/senate-bill/841/text/is (accessed 11.15.19).
STA, 2015. Krav för vägars och gators utformning, Publikationsnummer 2015:086.
Stahlfest Holck Skov, R., Iversen, L.M., 2015. Noise from electric vehicles.
Strandman, J., 2009. Strålsäkerhetsmyndighetens allmänna råd om begränsning av allmänhetens
exponering för elektromagnetiska fält. Strålsäkerhetsmyndighetens författningssamling 7.
44 VTI rapport 1053A
Swedish Transport Administration, 2012. Väg eller järnväg på min tomt - Hur får jag ersättning?
Swedish Transport Administration.
Tell, R.A., Kavet, R., 2016. ELECTRIC AND MAGNETIC FIELDS <100 KHZ IN ELECTRIC AND
GASOLINE-POWERED VEHICLES. Radiat Prot Dosimetry 172, 541–546.
https://doi.org/10.1093/rpd/ncv533
Timmers, V.R.J.H., Achten, P.A.J., 2016. Non-exhaust PM emissions from electric vehicles.
Atmospheric Environment 134, 10–17. https://doi.org/10.1016/j.atmosenv.2016.03.017
Tongur, S., 2018. Preparing for takeoff : Analyzing the development of electric road systems from a
business model perspective.
UN, 2017. UN Regulation No. 138 Uniform provisions concerning the approval of Quiet Road
Transport Vehicles with regard to their reduced audibility.
UN-ECE, 2015. UN-ECE Regulation No. 51 Uniform provisions concerning the approval of motor
vehicles having at least four wheels with regard to their sound emissions.
Waldmann-Selsam, C., Balmori-de la Puente, A., Breunig, H., Balmori, A., 2016. Radiofrequency
radiation injures trees around mobile phone base stations. Sci. Total Environ. 572, 554–569.
https://doi.org/10.1016/j.scitotenv.2016.08.045
Warnke, U., Luttichau, M. von, 2009. Bees, birds and mankind: destroying nature by “electrosmog,”
A Brochure Series by the Competence Initiative for the Protection of Humanity, Environment
and Democracy. E. Oppenheimer and Sons., South Africa.
WHO, 2019. WHO | What are electromagnetic fields? [WWW Document]. WHO. URL
http://www.who.int/peh-emf/about/WhatisEMF/en/ (accessed 8.13.19).
Wiltschko Roswitha, Thalau Peter, Gehring Dennis, Nießner Christine, Ritz Thorsten, Wiltschko
Wolfgang, 2015. Magnetoreception in birds: the effect of radio-frequency fields. Journal of
The Royal Society Interface 12, 20141103. https://doi.org/10.1098/rsif.2014.1103
Wyszkowska, J., Shepherd, S., Sharkh, S., Jackson, C.W., Newland, P.L., 2016. Exposure to
extremely low frequency electromagnetic fields alters the behaviour, physiology and stress
protein levels of desert locusts. Sci Rep 6, 36413. https://doi.org/10.1038/srep36413
Zethraeus, D., 2017. Email about installation of electric road, Elonroad.
Zetterberg, K., 2017. Ledningsarbete inom det statliga vägområdet. Swedish Transport
Administration.
Zhang, X., 2010. Prediction of high-speed train noise on Swedish tracks. SP Technical Research
Institute of Sweden 48.
Swedish National Road and Transport Research Institute • www.vti.se • vti@vti.se • +46 (0)13–20 40 00
ABOUT VTI
The Swedish National Road and Transport Research Institute (VTI), is an independent and internationally prominent research institute in the transport sector. Our principal task is to conduct research and develop-
ment related to infrastructure, traffic and transport. We are dedicated to the con-tinuous development of knowledge pertaining to the transport sector, and in this way contribute actively to the attainment of the goals of Swedish transport policy.
Our operations cover all modes of transport, and the subjects of pavement technology, infrastructure maintenance, vehicle technology, traffic safety, traffic analysis, users of the transport system, the environment, the planning and deci-sion making processes, transport economics and transport systems. Knowledge that the institute develops provides a basis for decisions made by stakeholders in the transport sector. In many cases our findings lead to direct applications in both national and international transport policies.
VTI conducts commissioned research in an interdisciplinary organisation. Employ-ees also conduct investigations, provide counseling and perform various services in measurement and testing. The institute has a wide range of advanced research equipment and world-class driving simulators. There are also laboratories for road material testing and crash safety testing.
In Sweden VTI cooperates with universities engaged in related research and education. We also participate continuously in international research projects, networks and alliances.
The Institute is an assignment-based authority under the Ministry of Infrastruc- ture. The Institute holds the quality management systems certificate ISO 9001 and the environmental management systems certificate ISO 14001. Certain test methods used in our labs for crash safety testing and road materials testing are also certified by Swedac.
top related