assembly and operating manual svh
Post on 04-Oct-2021
12 Views
Preview:
TRANSCRIPT
Translation of Original Operating Manual
Assembly and Operating ManualSVHServo-electric 5-Finger Gripping Hand
Imprint
202.00 | SVH | Assembly and Operating Manual | en | 389734
ImprintCopyright:This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rightsreserved. Any reproduction, processing, distribution (making available to third parties),translation or other usage - even excerpts - of the manual is especially prohibited andrequires our written approval.
Technical changes:We reserve the right to make alterations for the purpose of technical improvement.
Document number: 389734
Version: 02.00 | 06/05/2019 | en
© SCHUNK GmbH & Co. KGAll rights reserved.
Dear Customer,thank you for trusting our products and our family-owned company, the leadingtechnology supplier of robots and production machines.Our team is always available to answer any questions on this product and other solutions.Ask us questions and challenge us. We will find a solution!Best regards,Your SCHUNK team
SCHUNK GmbH & Co. KGSpann- und GreiftechnikBahnhofstr. 106 – 134D-74348 Lauffen/NeckarTel. +49-7133-103-0Fax +49-7133-103-2399info@de.schunk.comschunk.com
Table of contents
02.00 | SVH | Assembly and Operating Manual | en | 389734
3
Table of contents1 General.................................................................................................................... 5
1.1 About this manual ................................................................................................ 51.1.1 Presentation of Warning Labels ............................................................... 51.1.2 Applicable documents .............................................................................. 61.1.3 Variants..................................................................................................... 6
1.2 Warranty .............................................................................................................. 61.3 Scope of delivery .................................................................................................. 6
2 Basic safety notes ................................................................................................... 82.1 Intended use......................................................................................................... 82.2 Consequences of inappropriate use..................................................................... 82.3 Ambient conditions and operating conditions ..................................................... 92.4 Product safety ...................................................................................................... 9
2.4.1 Protective equipment............................................................................... 92.4.2 Structural changes, attachments and modifications ................................ 9
2.5 Personnel qualification....................................................................................... 102.6 Personal protective equipment.......................................................................... 102.7 Notes on particular risks..................................................................................... 112.8 Notes for integrators .......................................................................................... 13
3 Technical data......................................................................................................... 143.1 Outer dimensions ............................................................................................... 143.2 Basic data ........................................................................................................... 143.3 Electrical operating data..................................................................................... 143.4 Data assembly board .......................................................................................... 153.5 Name plate ......................................................................................................... 15
4 Design and description............................................................................................ 164.1 5‐Finger Gripping Hand ...................................................................................... 164.2 Assembly board .................................................................................................. 18
5 Assembly and installation ....................................................................................... 195.1 Assembly and installation on an assembly board............................................... 215.2 Starting SCHUNK GUI Diagnostics....................................................................... 235.3 Extended use on assembly board....................................................................... 235.4 Mounting to a robot or moving unit................................................................... 245.5 System requirements for commissioning .......................................................... 26
6 Operation ............................................................................................................... 276.1 Homing ............................................................................................................... 276.2 Operation ........................................................................................................... 29
Table of contents
402.00 | SVH | Assembly and Operating Manual | en | 389734
7 Troubleshooting ..................................................................................................... 307.1 Communication via USB interrupted.................................................................. 307.2 Communication via Ethernet interrupted .......................................................... 307.3 Fingers are colliding............................................................................................ 307.4 SVH is not reacting, not moving or stops suddenly ............................................ 307.5 Unusual noise during operation ......................................................................... 31
8 Maintenance .......................................................................................................... 32
General
02.00 | SVH | Assembly and Operating Manual | en | 389734
5
1 General1.1 About this manual
This manual contains important information for a safe andappropriate use of the product.This manual is an integral part of the product and must be keptaccessible for the personnel at all times.Before starting work, the personnel must have read andunderstood this operating manual. Prerequisite for safe working isthe observance of all safety instructions in this manual.Illustrations in this manual are provided for basic understandingand may differ from the actual product design.In addition to these instructions, the documents listed underApplicable documents [} 6] are applicable.
1.1.1 Presentation of Warning Labels
To make risks clear, the following signal words and symbols areused for safety notes.
DANGERDanger for persons!Non-observance will inevitably cause irreversible injury or death.
WARNINGDangers for persons!Non-observance can lead to irreversible injury and even death.
CAUTIONDangers for persons!Non-observance can cause minor injuries.
NOTICEMaterial damage!Information about avoiding material damage.
General
602.00 | SVH | Assembly and Operating Manual | en | 389734
1.1.2 Applicable documents
• General terms of business*• Mecovis protocol description/interface description• Instructions for GUI diagnostics• SVH_Protocoll_Specification_v0 4The documents marked with an asterisk (*) can be downloaded onour homepage schunk.comAdditional information is available on the enclosed CD.
1.1.3 Variants
This operating manual applies to the following variations:• SVH right• SVH left
1.2 WarrantyIf the product is used as intended, the warranty is valid for 12 months from the ex-works delivery date under the following conditions:• Observe the specified maintenance intervals, Maintenance [} 32]• Observe the ambient conditions and operating conditions,
Ambient conditions and operating conditions [} 9]Parts touching the workpiece and wear parts are not included inthe warranty.After the warranty period has expired, SCHUNK can no longerguarantee safety features without first performing a maintenanceservice.
1.3 Scope of deliveryThe scope of delivery includes• Servo-electric 5-Finger Gripping Hand SVH in the version
ordered• Operating manual• Mecovis parameter set• Assembly board (integrated: BananaPI, USB Isolator, Brainbox,
FWK-ISO 115, var. cables)• Power supply unit and cable• Zarges boxes (packaging material)• CD (software)
General
02.00 | SVH | Assembly and Operating Manual | en | 389734
7
The enclosed CD contains:
Directory ContentsBrainbox • Manufacturer documents (software and
documentation) for Brainbox (RS485/USBinterface converter)
Mecovis software • Installation files for the Mecovis softwareSVH_Manuals • BananaPI user interface
• Instructions for Interactive Diagnosis andControl GUI for SCHUNK SVH
• Protocol specification for SCHUNK FiveFinger Hand
• Mecovis S5FH-controller user's guide• DOF Diagram/range of movement/joint
torque• Schunk Readme
CD content may change in line with technological developments.
Basic safety notes
802.00 | SVH | Assembly and Operating Manual | en | 389734
2 Basic safety notes2.1 Intended use
The product features a multi-functional design intended forgripping objects ranging from 1-850 g. It is important to ensure that no fragile, sharp or sharp-edgedobjects, or objects with an edge length of over 50 cm are handled.• Gripping objects of a higher weight is only permitted after
consultation with the manufacturer.• The product is intended for installation in a machine. The
requirements of the applicable guidelines and standards mustbe observed and complied with. If applicable, it may be requiredto provide proof of safety for the machine to be used. Thesafety features of this product were established/certified onlyfor use as described in this operating manual.
• The safety-related information contained in the "Electricalequipment of machines" standard (DIN EN 60204) must beobserved. Commissioning is only permitted in compliance withEMC directives (2014/30/EU).
• The product may be used only in the context of its definedapplication parameters Technical data [} 14].
• The product may only be used within the scope of its technicaldata, Technical data [} 14].
• The product is intended for industrial and industry-oriented use.• For appropriate use of this unit, it is essential to observe the
technical data and assembly and operation notes in this manualand to comply with the maintenance intervals.
2.2 Consequences of inappropriate useThe safety of the product cannot be guaranteed in the event ofinappropriate use (i.e. actions carried out in a manner that is notcompliant with this operating manual). It is possible for the safetyof this product to be permanently impaired/damaged as the resultof one single inappropriate use.Examples of inappropriate use include the product being used as apress tool, being overloaded, or being used in an environment thatis not low-dust/dry.
Basic safety notes
02.00 | SVH | Assembly and Operating Manual | en | 389734
9
2.3 Ambient conditions and operating conditionsRequired ambient conditions and operating conditionsIncorrect ambient and operating conditions can make the productunsafe, leading to the risk of serious injuries, considerable materialdamage and/or a significant reduction to the product's life span.• Make sure that the product is used only in the context of its
defined application parameters, Technical data [} 14].• Make sure that the product is a sufficient size for the
application.• Make sure that the environment is free from splash water and
vapors as well as from abrasion or processing dust. Exceptionsare products that are designed especially for contaminatedenvironments.
2.4 Product safetyDangers arise from the product, if:• the product is not used in accordance with its intended
purpose.• the product is not installed or maintained properly.• the safety and installation notes are not observed.Avoid any manner of working that may interfere with the functionand operational safety of the product.Wear protective equipment.
NOTEMore information is contained in the relevant chapters.
NOTEThe availability of the safety functions is ensured only after a fullsystem start.
2.4.1 Protective equipment
Provide protective equipment per EC Machinery Directive.
2.4.2 Structural changes, attachments and modifications
Implementation of structural changesBy conversions, changes, and reworking, e.g. additional threads,holes, or safety devices can impair the functioning or safety of theproduct or damage it.• Structural changes should only be made with the written
approval of SCHUNK.
Basic safety notes
1002.00 | SVH | Assembly and Operating Manual | en | 389734
2.5 Personnel qualificationInadequate qualifications of the personnelIf the personnel working with the product is not sufficientlyqualified, the result may be serious injuries and significantproperty damage.• All work may only be performed by qualified personnel.• Before working with the product, the personnel must have read
and understood the complete assembly and operating manual.• Observe the national safety regulations and rules and general
safety instructions.The following personal qualifications are necessary for the variousactivities related to the product:
Trained electrician Due to their technical training, knowledge and experience, trainedelectricians are able to work on electrical systems, recognize andavoid possible dangers and know the relevant standards andregulations.
Qualified personnel Due to its technical training, knowledge and experience, qualifiedpersonnel is able to perform the delegated tasks, recognize andavoid possible dangers and knows the relevant standards andregulations.
Instructed person Instructed persons were instructed by the operator about thedelegated tasks and possible dangers due to improper behaviour.
Service personnel ofthe manufacturer
Due to its technical training, knowledge and experience, servicepersonnel of the manufacturer is able to perform the delegatedtasks and to recognize and avoid possible dangers.
2.6 Personal protective equipmentUse of personal protective equipmentPersonal protective equipment serves to protect staff againstdanger which may interfere with their health or safety at work.• When working on and with the product, observe the
occupational health and safety regulations and wear therequired personal protective equipment.
• Observe the valid safety and accident prevention regulations.• Wear protective gloves to guard against sharp edges and
corners or rough surfaces.• Wear heat-resistant protective gloves when handling hot
surfaces.• Wear protective gloves and safety goggles when handling
hazardous substances.• Wear close-fitting protective clothing and also wear long hair in
a hairnet when dealing with moving components.
Basic safety notes
02.00 | SVH | Assembly and Operating Manual | en | 389734
11
2.7 Notes on particular risksGenerally valid:• Remove the energy supplies before installation, modification,
maintenance, or adjustment work.• Make sure that no residual energy remains in the system.• Do not move parts by hand when the energy supply is
connected.• Do not reach into the open mechanism or the movement area
of the unit.• Perform maintenance, modifications, and additions outside the
danger zone.• Secure the product during all operations against uncontrolled
activation.• Take a precautionary approach by maintenance and
disassembly.• Only specially trained staff should disassemble the product.• Ensure that the operating personnel are fit for use.
WARNINGRisk of injury from unexpected movements of the machine/system!
WARNINGRisk of injury due to hot surfaces.In high ambient temperatures, it is possible for the product to beexposed to excessive heat, causing the surfaces to become hot.• Wear protective gloves.• Allow the product to cool to at least 40°C before touching it.
WARNINGRisk of injury due to sudden movements in case of EMCmalfunctions!If the EMC directive is not observed when connecting theproduct, malfunctions in the control units and drives can causeunexpected machine movements.• Observe the EMC directive when connecting the product.
Basic safety notes
1202.00 | SVH | Assembly and Operating Manual | en | 389734
WARNINGIn case of overload, risk of injury due to sudden movements!If the product is overloaded, the integrated brake will no longerfunction properly. This may result in sudden machinemovements.• Operate the product within the specifications defined at all
times.
WARNINGIn case of product malfunction, risk of injury due to suddenmovements!Electrical devices are not generally protected against failure.• Therefore, the user is responsible for ensuring that the
machine is brought into a safe state in case of productmalfunction.
WARNINGRisk of injury due to sudden movements in case of electricalmalfunctions!Electrical malfunctions can lead to sudden movements in themachine.• During transport and handling, do not bend any of the
components or change the insulation clearance.• To avoid damage due to electrostatic charges, do not touch
the electrical components.• Properly execute all grounding, fastening and cabling work in
accordance with applicable regulations.
Basic safety notes
02.00 | SVH | Assembly and Operating Manual | en | 389734
13
2.8 Notes for integrators• The integrator must verify that the safety-related parts of the
control units meet PL "d" with category 3 structure, as long as adifferent classification has not emerged from the risk analysisperformed by the integrator.
• If the gripper is used on a robot with removable devices andcollaborative operation (e.g. wireless emergency stop), therequirements for this must be verified by the integrator.
• The integrator must verify that the static and dynamic forcesthat are produced jointly by the load and the end effectors arewithin the robot's bearing load capacity and dynamicperformance levels.
• The settings for commissioning the robot must be specified/factored in by the integrator.
• The trade association requirements for hazard and injuryprevention in workplaces using collaborative robots must befactored in and verified by the integrator.
• The trade association requirements for the medical fitness andprofessional qualifications of operating personnel forcollaborative robots must be considered and verified by theintegrator.
• The MRK robot is to be checked for correct installation after anydangerous collisions. Dangerous collisions means those that arenot covered under normal conditions of use (e.g. if the useractively collides with or presses against the gripper contrary tothe instructions for use)
• The integrator is to equip the MRK robot system with a category0 emergency stop pursuant to IEC 60204 -1, which also disablesthe gripper.
Technical data
1402.00 | SVH | Assembly and Operating Manual | en | 389734
3 Technical data3.1 Outer dimensions
Dimensions
The right and left hands are laterally inverted. The dimensions areidentical.
3.2 Basic data
Designation SVHRight Left
Ident number 0306456 0306457Overall length [mm] 242.5Hand width [mm] 92Max. finger width [mm] 19.6Weight [kg] 1.3IP rating 20Min. ambient temperature [°C]Max. ambient temperature [°C]
1040
Noise emission [dB(A)] < 60Number of joints 20
3.3 Electrical operating dataDesignation SVHPower supply 24 V DC ±5%Max. current input 3.5 ASensor system -Interfaces • FWA115 flat change system
• RS 485
Technical data
02.00 | SVH | Assembly and Operating Manual | en | 389734
15
3.4 Data assembly boardDesignation ValueIdent number 5524201Dimensions (L x W x H) [mm] 300 x 300 x 85Supply voltage [VDC] 24 ± 5%Max. Current input [A] 3.75Operating elements • Illuminated ON/OFF push
buttons• USB/Ethernet toggle switch
Weight [kg] 2.7Single-board computer BananaPI with SD slotInterfaces • Flat change system
• Socket for external powersupply unit
• USB socket• Ethernet socket
3.5 Name plateThe name plate is placed in the interior on the heat sink.
Design and description
1602.00 | SVH | Assembly and Operating Manual | en | 389734
4 Design and descriptionThe 5‐finger gripping hand SVH comes with an assembly board fordemonstration and testing purposes.
4.1 5‐Finger Gripping HandThe 5‐finger gripping hand SVH is a servo-electric gripping modulewith integrated control and regulation electronics that is largely arecreation of the human hand.The 5‐finger gripping hand was designed SVH to be attached to astandard LWA 4P or LWA 4D lightweight arm.The defined mechanical and electrical interface also makes itpossible to attach it to other commercially available industrial andlightweight robots.In this case, the 5‐finger gripping hand SVH must always beoperated within its technical specifications, Technical data [} 14].The 5‐finger gripping hand SVH is available in two designs,corresponding to the right and left human hands. The dimensionsand operating data are identical for both designs.
Overall View of the 5-Finger Hand SVH
1 Fingers 3 Wrist2 Thumbs 4 Flat change system
The 5‐finger gripping hand SVH is suitable for mobile applicationsthanks to its design and low power consumption; also withaccumulator power supply.Possible movements include:• Bending and extending the fingers• Spreading out the hand• Pivoting and bending the thumb
Design and description
02.00 | SVH | Assembly and Operating Manual | en | 389734
17
A slip-resistant, elastic gripping surface on the fingers and thumbsallow objects to be gripped securely.A total of 9 drive motors control the movements of the 5-fingergripping hand's fingers and thumb. SVH.The control, regulation and power electronics are integrated intothe wrist of the 5‐finger gripping hand SVH .Attaching it to a lightweight arm or to another application ispossible via the SCHUNK flat change system.The power supply and control lines for the 5‐finger gripping handSVH are connected to the flat exchange system's adapter boardswith spring contacts.The 5‐finger gripping hand SVH can either operate on the assemblyboard included or on another piece of equipment (connection via theFWK115-ISO flat change system), Assembly and installation [} 19].
Design and description
1802.00 | SVH | Assembly and Operating Manual | en | 389734
4.2 Assembly boardFor initial commissioning, demonstrations, test runs or softwaredevelopment, the 5‐finger gripping hand SVH can be mounted andoperated on the assembly board included.A toggle switch switches between the USB and Ethernet interfaces.Firstly, the 5-finger gripping can be controlled via the USBinterface. In this case, the Mecovis company software provided isused. This software is only intended for demonstration purposes,not for use with products in continuous operation.The software is not supported by SCHUNK.When controlling the 5-finger gripping hand via the Ethernetinterface, the SCHUNK diagnostics and control GUI is used.
Assembly board with operating and control panels
1 FWK-ISO 115 flat changesystem
4 Ethernet connection
2 Connection for the"Power IN 24 VDC"network device
5 USB/Ethernet toggleswitch
3 Illuminated ON/OFF pushbuttons
6 USB connection
The assembly board is basically comprised of:• the operating and control panels• BananaPI (single-board computer)• RS485/USB interface converter• USB Isolator• FWK115‐ISO flat change system
Assembly and installation
02.00 | SVH | Assembly and Operating Manual | en | 389734
19
5 Assembly and installation
WARNINGRisk of injury when the machine/system moves unexpectedly!Switch off power supply.
NOTEDepending on the application, it can be useful to perform basicconfiguration steps before the mechanical installation.
Recommended tool: hexagon socket wrench, size 5
NOTICERisk of damage when using screws that are too long!• Observe the maximum depth of engagement permitted for
the mounting screws.
NOTICERisk of damage when using unsuitable connecting elements!• SCHUNK recommends using SCHUNK connecting elements.
Check the flatness of the bolting surfaceThe values refer to the entire bolting surface.
NOTICERisk of operational malfunction due to torn or pinched lines!If electrical lines are too short or installed incorrectly, they maybecome pinched or torn by the movement of the module.• Factor in operating movements when connecting the module.
NOTICERisk of operational malfunction due to short circuit or incorrectconnections!• Before connecting, ensure that the electrical lines are de-
energized.• Be sure to distribute the clamps correctly.
Assembly and installation
2002.00 | SVH | Assembly and Operating Manual | en | 389734
NOTICEPermanent damage to the electronics possible!• If the power supply is separated, carry out potential
equalization between the two supply voltages (join thegrounds).
• Only the positive pole may be switched off; the GND motorcable must always remain connected.
NOTEIn order to supply the hand with energy, a power supply unit mustbe used that is able to supply sufficient power for the hand. Makesure the dimensions of the cable cross-section are adequate whencabling.
The assembly and installation of the SVH 5‐finger gripping handare different for the configurations listed below.
Operating on the assembly board• Demonstration mode with SCHUNK Diagnostics and Control GUI• Extended use on assembly board• Free programming using the Mecovis software, for further
information see enclosed CD.
Operating on an external robot arm• Mounting with the FWK11‐ISO flat change system• Free programming• The operator is responsible for the mechanical connection,
electrical connection and software used.
Assembly and installation
02.00 | SVH | Assembly and Operating Manual | en | 389734
21
5.1 Assembly and installation on an assembly boardCommissioning via a network connection and the SCHUNKDiagnostics and Control GUI is described below.
Flat change system on an assembly board
1 Clamping ring withclamping screws
3 Adapter board
2 Centering pin
Connection to the 5-finger gripping hand SVH
1 Flange with seal formechanical mounting
3 Bore hole for centeringpin
2 Adapter board
Assembly and installation
2202.00 | SVH | Assembly and Operating Manual | en | 389734
Ø Disconnect the connection plug of the external network device.Ø Open the clamping ring on the flat changing system on the
assembly board.Ø Place the wrist of the 5‐finger gripping hand in the flat changing
system so that the centering pin aligns with the bore hole.Ø Tighten the clamping screws on the clamping ring.Ø Plug the network cable of the external computer into the
Ethernet interface on the assembly board.Ø Switch the toggle switch on the assembly board to the
"Ethernet" position.Ø Plug the external network device into the connection on the
assembly board.Ø Make sure that the 5‐finger gripping hand can move freely.Ø Switch the illuminated ON/OFF push button to "ON".✓ The single-board computer in the assembly board starts up.
The 5‐finger gripping hand performs a reset cycle to detectthe end stops for the fingers.
Powering downØ Switch the illuminated ON/OFF push button to "OFF".
Assembly and installation
02.00 | SVH | Assembly and Operating Manual | en | 389734
23
5.2 Starting SCHUNK GUI DiagnosticsSCHUNK GUI Diagnostics is implemented as a website independentof any operating system and can be used with the browser of yourchoice.
NOTEThe software has been tested by SCHUNK with Firefox (Mozilla)and Chrome (Google). For additional information, see the file "Instructions_for_GUI-Diagnostics.pdf" on the CD enclosed.
5.3 Extended use on assembly boardØ Switch the illuminated ON/OFF push button to "OFF".Ø Plug the USB cable of the external computer into the USB
interface on the assembly board.Ø Switch the toggle switch on the assembly board to the "USB"
position.Ø Make sure that the 5‐finger gripping had can move freely.Ø Switch the illuminated ON/OFF push button to "ON".This bypasses the single-board computer in the assembly board.The 5-finger hand can be controlled with an external software viathe USB interface.Further information about the SCHUNK ROS driver at http://wiki.ros.org/schunk_svh_driver.
Assembly and installation
2402.00 | SVH | Assembly and Operating Manual | en | 389734
5.4 Mounting to a robot or moving unit
CAUTIONRisk of injury due to the workpiece falling!In the event of a power failure or incorrect gripping process, thegripped workpiece may fall.• Ensure that the gripping process is performed correctly with a
suitable gripping force.• Keep distance.• Wear safety boots.
CAUTIONRisk of injury if the 5-finger gripping hand is torn from the robotarm or moving unit!If the mounting process has not been performed properly, the 5‐finger gripping hand may come loose from the robot arm.• Mount the flat change system properly.• Tighten the lateral cylindrical screw to the clamping ring with a
spanner wrench.
Using the flat change system, the gripping hand can be mountedon an external robot arm.
Connection to the flat change system
1 Supply voltage 24VDC onsoldering surfaces
3 RS485/USB interfaceconverter ("Brainbox")
2 Flat change system 4 USB isolatorJST JST plug connector
Assembly and installation
02.00 | SVH | Assembly and Operating Manual | en | 389734
25
The FWK115‐ISO flat change system is comprised of the followingcomponents:• Clamping ring• Flange• Adapter board• Centering pin• Seal• Screws
NOTEM3 mounting screw and O-ring are attached to the flat changesystem.
Mount the FWK115‐ISO flat change system on the external robotarm as follows:■ Ensure that the interface is de-energized.Ø Align the flange with the centering pin and place on the
centering pin.Ø Fasten the flange with 6 M3 screws.Ø Place the wrist of the gripping hand in the flat changing system
so that the centering pin aligns with the bore hole.Ø Tighten the clamping screws on the clamping ring.Ø Secure the clamping ring with the lateral cylindrical screw.
WARNINGRisk of injury due to incorrect electrical connection!If the electrical connection is not performed properly, amalfunction or short circuit may occur.• The operator is responsible for executing the electrical
connection correctly.• Provide galvanic isolation of the USB signal (USB isolator).• Ventilate the room adequately in case of a short circuit.
Electrical connection is made at the adapter board of the FWK115-ISO flat change system.Ø Solder on the marked area of the soldering surfaces on the
input side of the 24 V DC and GND power supply lines.Ø Plug the JST connector of the signal lines in the JST adapter
board socket.Ø Connect the JST connector to the D‐Sub connection of the
RS485/USB interface converter ("Brainbox").
Assembly and installation
2602.00 | SVH | Assembly and Operating Manual | en | 389734
Pin allocation for D-Sub to JST plug connection
D-Sub pin Wire color Recommendedcable cross-section[mm²]
JST pin
1 White 0.1 42 Green 0.1 36 Brown 0.1 27 Yellow 0.1 1
Soldering surfaces
Designation Assignment Recommendedcable cross-section[mm²]
Recommended wirecolor
+UM +24 VDC supply 0.5 Red-UM GND supply 0.5 Black
NOTEThe clamps and the two-pronged sockets on the adapter boardare not used.
5.5 System requirements for commissioning• Electrical connection to the RS485/USB interface converter
("Brainbox") and USB isolator• USB cable between the USB isolator and PC• PC (laptop, etc.)• Control softwareCommissioning is dependent on the control software installed. Theoperator is responsible for complying with the technical specificationsof the 5‐finger gripping hand SVH, see Technical data [} 14].
Operation
02.00 | SVH | Assembly and Operating Manual | en | 389734
27
6 OperationThe following considerations generally apply to operations:• When the 5‐finger gripping hand SVH is mounted on an external
device (e.g. external robot arm), the operator is responsible forensuring the operational safety of this equipment.
• The fingers (excluding the thumb) can be carefully movedmanually in the event of a failure of the power supply. This willnot damage the drive. The thumb drives are self-locking in a de-energized state and cannot be manually moved.
• It is possible for the fingers to collide if controlled accordingly.Collisions will not cause damage, but the movement will beinterrupted.
When developing a customized control program for the 5‐fingergripping hand, SVH the following information applies.Note: English is the standard language in the field of softwaredevelopment. For this reason, English-language terms have beenused in the following:
6.1 HomingHoming is required after each startup of the SVH due to therelative angle measurement of the joints.For homing, SCHUNK recommends using a software end stop justbefore the mechanical end stop.The table below contains the following values:• direction of homing• recommended software end stop• total steps of each movement• recommended power limit• recommended movement speed
Operation
2802.00 | SVH | Assembly and Operating Manual | en | 389734
JOINT HOMINGDIRECTION
DISTANCEFROM HARDSTOP [°]
RANGE OFMOVEMENT[°]
HOMINGCURRENT[mA]
HOMINGSPEED
THUMBFLEXION
Stretch 5,000 170,000 50 100 rpm
THUMBOPPOSITION
Stretch 5,000 100,000 100 100 rpm
SPREAD Close 2,000 25,000 500 100 rpmINDEXFINGERPROXI
Stretch 2,000 40,000 200 500 rpm
INDEXFINGERDISTAL
Stretch 2,000 45,000 100 500 rpm
MIDDLEFINGERPROXI
Stretch 2,000 40,000 200 500 rpm
MIDDLEFINGERDISTAL
Stretch 2,000 45,000 100 500 rpm
RING FINGER Stretch 2,000 45,000 100 500 rpmLITTLEFINGER
Stretch 2,000 45,000 100 500 rpm
The following table contains the drive motor data. The maximumvalues specified must not be exceeded when developingcustomizations.
Operation
02.00 | SVH | Assembly and Operating Manual | en | 389734
29
JOINT NOM.CURRENT[mA]
MAX. PEAKCURRENT[mA]
TEMP.CURRENT[mA]
MAX RPM MOTORVOLTAGE [V]
THUMBFLEXION
191 605 500 10000 24
THUMBOPPOSITION
191 605 500 10000 24
SPREAD 169 688 350 13600 24INDEXFINGERPROXI
169 688 350 13600 24
INDEXFINGERDISTAL
176 360 350 11250 12
MIDDLEFINGERPROXI
196 688 350 13600 24
MIDDLEFINGERDISTAL
176 360 350 12500 12
RING FINGER 176 360 350 12500 12LITTLEFINGER
176 360 350 12500 12
6.2 OperationThe 5‐finger gripping hand SVH does not have any operableelements.Operating and running the 5-finger gripping hand SVH isdependent on the software installed.The 5‐finger gripping hand SVH can be operated via the assemblyboard, Assembly and installation on an assembly board [} 21].
Troubleshooting
3002.00 | SVH | Assembly and Operating Manual | en | 389734
7 Troubleshooting7.1 Communication via USB interrupted
Possible cause Corrective actionConnection cable defective Switch the toggle switch to the
"Ethernet" positionSignal path interrupted Check plug connector, cables
and electrical components
7.2 Communication via Ethernet interruptedPossible cause Corrective actionThe toggle switch on theassembly board in the wrongposition
Switch the toggle switch to the"Ethernet" position
Signal path interrupted Check plug connector, cablesand electrical components
Error while configuring networkaddress
Network address of thecomputer connected: 192.168.1.2 --- 192.168.1.255 Subnet mask: 255.255.255.0 URL in browser: 192.168.1.1
7.3 Fingers are collidingPossible cause Corrective actionThe power supply for the driveor the electronic control unit hasmalfunctioned
Check the power supply
Communication has beenconnected incorrectly
Check the signal cableconnection
Supply cable is defective Check supply cables for damage;replace if necessary
7.4 SVH is not reacting, not moving or stops suddenlyPossible cause Corrective actionThe power supply for the driveor the electronic control unit hasmalfunctioned
Check the power supply
Communication has beenconnected incorrectly
Check the signal cableconnection
Supply cable is defective Check supply cables for damage;replace if necessary
Troubleshooting
02.00 | SVH | Assembly and Operating Manual | en | 389734
31
7.5 Unusual noise during operationPossible cause Corrective actionMechanical damage Send the product to SCHUNK for
repair
Maintenance
3202.00 | SVH | Assembly and Operating Manual | en | 389734
8 MaintenanceØ Screw the 5-finger gripping hand to the supplied assembly
board.Ø Start the diagnostic software and compare nominal and actual
currents.Ø For fingers that show a difference in nominal currents: clean the
bearings in the joints and relubricate.
CleanØ Gently clean with clean-room swabs and non-flammable
cleaning agents.Ø Apply a thin layer of oil with new clean-room swabs. Use oil
labeled "Shell AF2".Ø If necessary, clean fingertips with isopropyl.The general rule is:• Only use solvent-free, water-based cleaning agents.• Do not use steam, coolant or high-pressure cleaners.• Do not allow cleaning agents to penetrate into electrical or
mechanical equipment.
Repair
NOTICEThe product may only be disassembled by SCHUNK, otherwisethe mechanics or the internal electronics could becomedamaged!
The components of the 5-finger gripping hand are adapted to eachother. Repairs are only possible at the manufacturer.Ø For repair or replacement, send the product repair order to
SCHUNK with a repair order.
top related