AnnouncementsFirst Assignment posted:Due in class in one week (Thursday Sept 15th)http://www.physics.udel.edu/~jholder/Phys645/index.htm

Lecture 3 Overview

Loop Analysis with KVL & KCLMesh AnalysisThevenin/Norton equivalent circuits

Circuit analysis method 2a: KVL and KCLKirchoffs Voltage Law: Loop analysisThe sum of the voltages around a closed loop must be zero Draw the current direction in every branch (arbitrary) and label the voltage directions (determined by the defined current direction). Voltage on a voltage source is always from positive to negative end. Define either clockwise or counter-clockwise as positive direction for summing voltages. Once the direction is defined, use the same convention in every loop. Voltage across a resistor is +ve if voltage direction the same as current direction, -ve otherwise Apply KVL

Kirchoffs Voltage Law: MultiloopThe sum of the voltages around a closed loop must be zero Draw the current direction (arbitrary) and label the voltage directions (determined by the defined current direction). Define either clockwise or counter-clockwise as positive voltage direction. Once the direction is defined, use the same convention in every loop. Apply KVL

Say r=1, R1=3, R2=5, R3=10, =3VWhat are the currents?

Kirchoffs Current LawThe sum of the current at a node must be zero: Iin=IoutI=I2+I3 (1)=Ir+IR1+I2R2 (2)I3R3-I2R2 =0 (3)1I- 1I2- 1I3 = 0 (4)4I+5I2+ 0I3= 3 (5)Say r=1, R1=3, R2=5, R3=10, =3V0I- 5I2+10I3= 0 (6)

Last note on KCL KVL analysisIf solutions to currents or voltages are negative, this just means the real direction is opposite to what you originally definedTo deal with current sources: current is known, but assign a voltage across it which has to be solved

Another Sample Problem: Multiple Sources

Method 2b: Mesh AnalysisExample: 2 meshes (Mesh is a loop that does not contain other loops)Step 1: Assign mesh currents clockwise Step 2: Apply KVL to each mesh The self-resistance is the effective resistance of the resistors in series within a mesh. The mutual resistance is the resistance that the mesh has in common with the neighbouring mesh To write the mesh equation, evaluate the self-resistance, then multiply by the mesh current Next, subtract the mutual resistance multiplied by the current in the neighbouring mesh for each neighbour. Equate the above result to the driving voltage: taken to be positive if it tends to push current in the same direction as the assigned mesh currentMesh1: (R1+R2)I1 - R2I2 =1-2Mesh2: -R2I1+ (R2+R3)I2 =2-3Step 3: solve currents

Method 2b: Mesh Analysis

Another mesh analysis exampleFind the currents in each branchStep 1: Replace any combination of resistors in series or parallel with their equivalent resistanceStep 2: Assign mesh currents clockwise Step 3: Write the mesh equations for each mesh Left mesh: 11I1-6I2=9 Right mesh: -6I1+18I2=9Note:suppressed k for each resistor, so answer is in mAStep 4: Solve the equationsSolution: I1=4/3mA =1.33mA I2=17/18mA =0.94mA

Mesh analysis with a current sourceMagnitude of current in branch containing current source is IS , (although if the current flow is opposite to the assigned current direction the value will be negative). This works only if the current source is not shared by any other meshFor a shared current source, label it with an unknown voltage.

Mesh analysis with mixed sources Find Ix Identify mesh currents and label accordingly Write the mesh equationsMesh1: I1 =-2Mesh2:-4I1+8I2 -4I4=12Mesh3: 8I3 =-12Mesh4:-2I1-4I2 +6I4=10

I1= -2.0AI2= 1.5AI3= -1.5AI4= 2.0A

Ix=I2-I3Ix=3.0A

Method 3: Thevenin and Norton Equivalent CircuitsvTH= open circuit voltage at terminal (a.k.a. port)

RTH= Resistance of the network as seen from port(Vms, Ins set to zero)

Any network of sources and resistors will appear to the circuit connected to it as a voltage source and a series resistance

Norton Equivalent CircuitAny network of sources and resistors will appear to the circuit connected to it as a current source and a parallel resistance

Calculation of RT and RNRT=RN ; same calculation (voltage and current sources set to zero)Remove the load.Set all sources to zero (kill the sources)Short voltage sources (replace with a wire)Open current sources (replace with a break)

Calculation of RT and RN continuedCalculate equivalent resistance seen by the load

Calculation of VTRemove the load and calculate the open circuit voltage

Calculation of INShort the load and calculate the short circuit current(R1+R2)i1 - R2iSC = vs-R2i1 + (R2+R3)iSC = 0KCL

Source TransformationSummary: Thevenins TheoremAny two-terminal linear circuit can be replaced with a voltage source and a series resistor which will produce the same effects at the terminalsVTH is the open-circuit voltage VOC between the two terminals of the circuit that the Thevenin generator is replacingRTH is the ratio of VOC to the short-circuit current ISC; In linear circuits this is equivalent to killing the sources and evaluating the resistance between the terminals. Voltage sources are killed by shorting them, current sources are killed by opening them.

Summary: Nortons TheoremAny two-terminal linear circuit can be replaced with a current source and a parallel resistor which will produce the same effects at the terminalsIN is the short-circuit current ISC of the circuit that the Norton generator is replacingAgain, RN is the ratio of VOC to the short-circuit current ISC; In linear circuits this is equivalent to killing the sources and evaluating the resistance between the terminals. Voltage sources are killed by shorting them, current sources are killed by opening them.For a given circuit, RN=RTH

Maximum Power TransferWhy use Thevenin and Norton equivalents?Very easy to calculate load related quantitiesE.g. Maximum power transfer to the loadIt is often important to design circuits that transfer power from a source to a load. There are two basic types of power transferEfficient power transfer (e.g. power utility)Maximum power transfer (e.g. communications circuits)Want to transfer an electrical signal (data, information etc.) from the source to a destination with the most power reaching the destination. There is limited power at the source and power is small so efficiency is not a concern.

Maximum Power Transfer: Impedance matchingso maximum power transfer occurs whenandDifferentiate using quotient rule: Set to zero to find maximum:http://circuitscan.homestead.com/files/ancircp/maxpower1.htm