2016 - carfitrepair.com · steel, aluminum, galvanized steel, fiberglass *. substrates to be...

CAR REFINISH CONSUMABLES

GB

catalogue2016

Dear valued client,

Thank you very much for your interest in our high quality C.A.R.FIT product range. Our well thought through and efficient solutions have made C.A.R.FIT a well-known and respected brand in the international painting industry. We thank our clients for their trust in our products and we invite all those interested in our range of products to test and find out on the many advantages of C.A.R.FIT. Our team of product specialists will be there for you with ample expe-rience and helpful advice.

With this catalogue you will again find a new selection of innovative products that help to improve the work of the painter in terms of quality and quantity. Our new quick drying clearcoat are prominent examples for our permanent strive to always providing you with an optimum in cost whilst never compromising on our German Quality Thinking.

Open up new markets with a maximum in quality and experience the many advantages that our “Black Label” premium range holds for your clients’ business as well as your own.

Stay in touch with C.A.R.FIT and visit our website at www.carfitrepair.com. You will find up to date information on product innovations and events. We look forward to your visit!

Kind regards from Berlin, Germany

C.A.R.FIT

3catalogue

4catalogue

Suitable substrates Airless application

Cleaning Number of coats / Material thickness

Application viscosity Air drying / Flash-off

Use of measuring stick Low baking

Mixing ratio by volume: 2 components Infrared drying (short wave)

Addition of hardener/catalyst Orbital sander

Pot life of liquid materials Flat-bed sander

Application with putty knife / Pot life of the putty

Dry sandind by hand

Shake can Wet sandind by hand

Material application Application subsequent material

Spray can application Polishing

Cartridge gun application Keep frost protected

UB Suction gun application Keep out of direct sunlight

Paint roller application Attention / Note

Brush application See TDS

5catalogue

Contents

Premium Black Label Series 6

Putties 20

Paintworks materials 25

Thinners, Cleaners 36

Polishing materials 38

Protective coatings 40

Adhesives & sealants 42

Masking 45

Cloths 48

Accessories 50

6catalogue

Glass Putty

Articles Description Pcs. / pack

22701000 1 kg, w/hardener 8

VOC: < 250 g/LEU limit value: 2004/42/IIB(b)(250)

NEW GENERATION

Description Light 2K polyester filling putty reinforced with fiberglass for filling cracks, small holes and areas damaged by corrosion. This putty with innovative formula ideally suits for surface repair when maximum mechanical resistance and adhesion to a substrate are required. Due to the special formula the putty is much more soft and flexible than analogical products from other manufacturers; this gives substantial advantage during application. Another principal advantage of this material is the minimum pore formation that makes it possible to reduce a number of surface treatment operations in contrast with fiberglass putties from other manufacturers. Better surface quality, easier sanding and reduction of time expenditure gives to the new material the unprecedented superiority.

ApplicationFilling cracks, small holes and areas damaged by corrosion during cars and commercial vehicles repair.

Characteristics• Lightweight putty• Soft and flexible• High mechanical resistance combine with good adhesion to substrates• Low pore formation• Better surface quality• Can be wet sanded

SubstratesSteel, aluminum, galvanized steel, fiberglass*.

Substrates to be treated must be cleaned, dried, degreased with Silicone Remover and sanded with P80-P150 abrasives. Then the substrate must be cleaned again as described above.

3 % of BPO hardener

• To provide maximum corrosion protection it is recommended to apply the putty on an epoxy primer; • Do not apply the putty on thermoplastic materials and wash primers; • Follow the hardener mixing ratio; mix thoroughly.

Pot life 5.5 min at 20°CTmin = 5°C

15 min at 30°C20 min at 20°C30 min at 10°C

5 min / 80 cm Object temperature ≤ 80°C

Keep away from direct sunlight

Substrate pretreatment

Application

Further treatment

Technical data

Storage

Color greenish blue colorDensity 1170 g/L

Abrasives P100–180

P100 (initial sanding): orbit 5–7 mmP180 (finish sanding): orbit 3–5 mm

BLACK LABEL SERIES

*Do not apply on one component (etch and anticorrosive) primers and thermoplastics. Application on paintworks is not recommended.

7catalogue

Soft Uni Putty


22301000 1 L, w/hardener 8


DescriptionExtra light 2K polyester filling putty for car repair. The product has outstanding sanding properties and ability to absorb the vibration due to its high flexibility and therefore is very effective for large surface repair.

Application Eliminating car and commercial vehicle body imperfections.

Characteristics• Extra lightweight putty• High flexibility• Fine sanding properties• Can be wet sanded

SubstratesSteel, aluminum, galvanized steel, fiberglass *.

Substrates to be treated must be cleaned, dried, degreased with Silicone Remover and sanded with P80-P150 abrasives. Then the substrate must be cleaned again as described above.

3 % of BPO hardener

• To provide maximum corrosion protection it is recommended to apply the putty on an epoxy primer; • Do not apply the putty on thermoplastic materials and wash primers; • Follow the hardener mixing ratio; mix thoroughly.

Pot life 5.5 min at 20°CTmin = 5°C

15 min at 30°C25 min at 20°C30 min at 10°C

5 min / 80 cm Object temperature ≤ 80°C



Application

Further treatment

Technical data

Storage

Color light blue colorDensity 840 g/L

Abrasives P120–220

P120 (initial sanding): orbit 5 – 7 mmP220 (finish sanding): orbit 3 – 5 mm

NEW GENERATION

BLACK LABEL SERIES


8catalogue

Fill&Fine Putty anticorrosion protection

Description Two component basic universal filling putty for eliminating major and medium mechanical damages.First ever polyester putty with anticorrosive properties.

Application Universal filling putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free

surface, thus enabling the refinisher to use one product at all stages of repair (no need to use finishing putty)

• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid paintwork defects (deep sanding marks)

• Easy to apply in thin and thick coats• Does not clog the sandpaper• Anticorrosive properties.

SubstratesAll kinds of steel, flexible aluminium, OEM substrates*.



2-110-1000 1 kg, w/hardener 12

BLACK LABEL SERIES

Substrates to be treated must be cleaned, dried, degreased with C.A.R.FIT Silicone Remover and sanded

Add 2–3% BPO Hardener by weight

Pot life: 3–5 min at 20°C

16–30 min depending on ambient temperature

With P80–180

First with P150, then with P240


Color redDensity 1900 g/L


Application*

Further treatment

Storage

Standard sanding method

Recommended sanding method

With P80–320 (intermediate sanding step of 100 grit should be observed)

Technical data

ANTICORROSION


9catalogue


Light&Soft Putty

Description Two component polyester filling putty with a glass microsphere.

Application Basic/filling putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly

speeds up sanding and helps avoid paintwork defects (deep sanding marks)• Specific formula of the putty with hollow glass microspheres significantly reduces its density,

improves its filling power and leaves light gloss on the surface until cure is complete, allowing for better control of the repair zone

• Excellent sandability even a few days after application• Recommended for use on large body parts: roof, doors, trunk lid, bonnet, etc.

SubstratesAll kinds of steel, fiberglass plastics, OEM substrates*.


2-130-1300 1.3 kg, w/hardener 10

BLACK LABEL SERIES





With P80–180



Color beigeDensity 1260 g/L


Application*

Further treatment

Storage




Technical data

LOW DENSITy


10catalogue

BLACK LABEL SERIES

Glas&Soft Putty


2-170-1000 1 kg, w/hardener 12


Description Two component fiberglass-filled polyester putty.Perfect choice for the repair of body parts with significant mechanical damages, loss of carrier function and through holes. When applied, it produces a coat of significant thickness which cures in a uniform manner. Due to its homogeneous structure and a minimum number of pinholes, makes application of finishing putties unnecessary.

Application Fiberglass putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly

speeds up sanding and helps avoid deep sanding marks• Restores the carrier function of damaged parts• Easy application and uniform cure in thick coats• No sandpaper clogging• No need in additional processing with a finishing putty• Very good adhesion to steel, galvanized steel, flexible aluminium and fiberglass plastics.

SubstratesAll kinds of steel, flexible aluminium, fiberglass plastics, OEM substrates*.






Color blue/greenDensity 1750 g/L


Application*

Further treatment

Storage

With P80–180





Technical data


11catalogue






Color metallicDensity 1780 g/L


Application*

Further treatment

Technical data

Storage

Alu&Soft Putty


2-180-1000 1 kg, w/hardener 12


Description Two component aluminium-filled polyester putty.It is used as a basic filling putty, particularly, in the repair of metal surfaces exposed to high temperature and mechanical abuse.

Application For repairs on metal surfaces of cars and commercial vehicles.

Characteristics• Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free

surface, thus enabling the refinisher to use one product at all stages of repair (no need to use a finishing putty)

• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid deep sanding marks

• Retains its shape in thin coats• Easy to sand with Р150 grit abrasives, providing a smooth transition between the repair and the

undamaged surrounding area• Excellent adhesion.

SubstratesAll kinds of steel, flexible aluminium, OEM substrates*.

BLACK LABEL SERIES

With P80–180






12catalogue



Application*

Further treatment






Carbon Putty


2-135-1300 1.3 kg, w/hardener 10

Description Carbon fiber filled 2К polyester putty for badly damaged surfaces requiring extensive repair. It has been developed for restoring damaged surfaces, increasing the mechanical strength of the repaired element.

Application For repairs on metal surfaces of cars and commercial vehicles.

Characteristics• It can be sanded with comparatively high grit abrasives (P120–P150) • This putty is almost as hard as finishing coating that provide a smooth transition between the repair and the undamaged surrounding area during sanding • It can be applied directly prior to filler • Due to its paste-like consistency, the putty is easy to apply in 2–4 mm coats • Perfectly suitable for sanding by machine or wet sanding by hand • Does not clog abrasives • Easy to work also on surfaces with complicated shapes even when applying thicker layers • Very good adhesion.

SubstratesSteel (incl. galvanized), aluminum, fiberglass plastic, OEM substrates*.


Color blackDensity 1820–1840 g/L

Technical data

Storage

With P80–180





BLACK LABEL SERIES

13catalogue


Application

Further treatment

Substrates to be treated must be cleaned, dried, degreased with CA.R.FIT Silicone Remover and sanded

4:1 by volume with Hardener for 2K Fast Air Filler 4:1

5-30 sec, FORD 4 at +20°C

Pot life: up to 1 hour at 20°C

VOC: max 520 g/LEU limit value: 2004/42/IIB(c)(540)

2K Fast Air Filler 4:1

Art. Nr. Beschreibung VE

4-421-1250 1 L Filler grey + 0.25 L Hardener 12

4-422-1250 1 L Filler white + 0.25 L Hardener 12

4-423-1250 1 L Filler black + 0.25 L Hardener 12

4-421-3600 3.6 L Filler grey 4

4-422-3600 3.6 L Filler white 4

4-423-3600 3.6 L Filler black 4

4-424-0900 0.9 L Hardener 12

Description2К Fast Air Filler 4:1 is fast drying two component filler with high solid content. It has excellent sanding properties preventing clogging of sanding paper.ApplicationParticularly suitable for fast and small repair. Also can be used for other types of repair. Characteristics• Very fast drying• Air drying, low baking, IR drying• Corrosion protection• Very good adhesion• Manual / machine dry sanding. Substrates All kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings.

Color grey white black

Density 1460-1480 g/L 1510-1530 g/L 1420-1440 g/L

Technical data

1.6-2.2 mm / Inlet pressure: see spray gun manufacturer's tips

40 - 60 μm per 1 coat1 – 3 normal coats = 40 – 180 μm

Flash-off between coats: 5 – 7 min

Air drying: 2.5–3 h at 20°C

- Flash-off: 10 min at 20°C- Through drying: 15 – 20 min at 60°C

- Flash-off: 10 min at 20°C- Medium- / short wave infrared drying: 12–15 min

Sand with P360-500

Recoat with both waterborne and solvent-based topcoats

BLACK LABEL SERIES

14catalogue


4-410-3500 3.5 L Filler 2

4-410-1200 1 L Filler + 0.2 L Hardener 12

4-400-0700 0.7 L Hardener 12

VOC: <540 g/LEU limit value: 2004/42/IIB(c)(540)

Description Two component acrylic filler with excellent filling properties. 2K Hi-Build Acryl Filler 5:1 can be used instead of spray putty that provides shorter repair process and less material consumption.

Application For treatment of large areas recoated with polyester materials.

Characteristics• Excellent filling properties• Due to its good flow, the product is easy to sand even when applied in 2–4 coats• Does not drip even when applied with a spray gun with a 2.5 mm nozzle • Sanding by hand or dry-sanding by machine• Overcoatable with both waterborne and solvent-based coatings

SubstratesAll kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings.

2К Hi-Build Acryl Filler 5:1


5:1 by volume with Hardener for Filler Hi-Build 5:1

48–52 sec, FORD 4 mm at 20°С

Pot life: ca. 45 min at 20°C

- Flash-off: 10 min- Through-drying: 45 min at 60°C

Color greyDensity 1500-1550 g/L

- Flash-off: 10 min- Medium wave or short wave infrared drying: 12–15 min


Application

Further treatment

Technical data

1.8–2.2 mm / Inlet pressure:see spray gun manufacturer’s tips

70–80 μm dry film thicknessper one coat 2 - 3 normal layers Flash-off between coats: 7-10 min

Dry sanding: with P360–500


BLACK LABEL SERIES

15catalogue

Application

Further treatment

Technical data

Process conditions: temperature >15°C, relative humidity up to 75%

16-18 sec, FORD 4 mm at 20°C

ca 50 min at 20°C

- Flash-off at 20°C: 10 min- Drying to touch at 60°C: 10 min- Full hardness: 3 days

- Drying to touch at 20°C: 1 – 1.5 h- Full hardness: 4 days

Density ca. 1000 g/L (clear coat)

1.5 layers = 50 – 60 μ. Apply thin closed coat + 1 full wet coat Flash-off between layers: 5 – 7 min


7-450-1500 1 L Clearcoat + 0.5 L hardener 12

7-450-5000 5 L, Clearcoat 4

7-451-2500 2.5 L, Standard Hardener 4

Description Very fast curing 2K acrylic clear coat characterized by rapid early hardness. It is ready for polishing only after 15 minutes of forced drying at 60°C and cooling down.

Application For two-coat paintworks in car refinishing.

Characteristics• Very good flow and leveling properties• High gloss and hardness• Well balanced pot life enables safe application• Outstanding durability due to chemical and weather resistance• High solid content • Conforms with VOC EU limit value.

SubstratesSolvent- / waterborne basecoats, OEM coatings.

2K HS Rapid Clearcoat VOC

VOC: < 420 g/LEU limit value: 2004/42/IIB(d)(420)

2:1 with hardener for 2K HS Rapid Clearcoat VOC

1.3 mm / Inlet pressure: see spray gun manufacturer’s tips

- Drying to polish at 60°C: 15 min- Drying to polish at 20°C: 3.5 - 4 h

BLACK LABEL SERIES

Storage


16catalogue

BLACK LABEL SERIES

VOC: 360 g/LEU limit value: 2004/42/IIB(d)(420)

Rapid Clearcoat 1:1


7-185-0500 500 ml, Clearcoat 12

7-335-0500 500 ml, Hardener 12

Description

А high-gloss two-pack clear coat with very high solid content for fast repair of vehicle refinishing with conventional and waterborne basecoats.

Due to very high solid content the clear coat is notable for its high efficiency while application; therefore it stands out against a background of other analogical clear coats.

Application For two-coat paintworks in car and commercial vehicle refinishing.

Characteristics• Extremely fast drying • Due to slow speed of filming at the first moment after application, the clear coat absorbs the

paint overspray nicely. • Very high-gloss• Very good flow • UV-resistant (does not yellow) and scratch-resistant • Solid film with good chemical and mechanical resistance.

SubstratesWaterborne and solvent born basecoats, OEM coatings.

Application

Further treatment

Technical data

1:1 with Hardener for Rapid Clearcoat


Pot life: up to 30 min at 20°C

- Flash-off at 20°C: 10 min- Drying at 60°C: 15-20 min

- Dust dry at 20°C: 20–25 min- Dry to touch at 20°C: 45-55 min- Polishing at 20°C: after 90 – 120 min- Full curing at 20°C: 5 hours

Density ca. 1010 g/L

1.3–1.5 mm / Inlet pressure: see spray gun manufacturer’s tipsFlash-off between the coats: 5 - 7 min

2 normal coats = 40-50 μm dry film thickness

Storage


17catalogue


7-400-1500 1 L, Clearcoat + 0.5 L hardener 12

7-400-5000 5 L, Clearcoat 4

7-435-2500 2.5 L, Standard Hardener 4

7-436-2500 2.5 L, Slow Hardener 4

7-437-2500 2.5 L, Fast Hardener 4

Description 2К Ultra HS Clearcoat is a two-component high-gloss clear coat for car refinishing with conventional and waterborne paint materials.


Characteristics• Scratch resistance• Very good flow• UV resistance• Optimized for application in spray booths and preparation zones.

SubstratesWaterborne and solventborne basecoats, OEM coatings.

2:1 with Hardener for 2K Ultra HS Clearcoat

15–17 sec, FORD 4 (+20°С)

Pot life: up to 1.5 h at 20°C

Flash-off: 7–10 minShort- / medium wave infrared drying: 10 min

Density ca. 960 g/L

Application

Further treatment

Technical data

1.3 mm / Inlet pressure: see spray gunmanufacturer’s tips

2 full coats = 50–55 μm Flash-off between coats: 5-10 min

2K Ultra HS Clearcoat

BLACK LABEL SERIES

SCRATCH RESISTANT

VOC: 535 g/LEU limit value: 2004/42/IIB(e)(840)

HardenerFlash-off: Drying at 60°C

Dry through at 20°CPolishing at 20°CFull hardness at 20°C

Standard7 - 10 min30 min

6 - 7 h10 - 11 h5 - 7 days

Fast7 - 10 min20 min

4 - 5 h8 - 9 h5 - 7 days

Slow7 - 10 min40 min

8 - 9 h11 - 12 h5 - 7 days

Storage


18catalogue

Silicone Remover “Strawberry”


7-550-1000 1 L 12

7-550-5000 5 L 4

VOC: 750 g/LEU limit value: 2004/42/IIB(a)(850)

Description Strawberry scented cleaning agent based on volatile organic solvents for initial cleaning of old/OEM coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product.

Application Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish.

SubstratesMetal and plastic parts, polyester putties, primers, fillers, fully cured old or fresh coatings.

Technical dataDensity 740–750 g/L

Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings

– Clean the substrate with C.A.R.FIT Silicone Remover “Strawberry”– Apply with a spray gun, a cloth or a sponge


Application

Pigment PastePigment paste for 1К and 2К acrylic fillers based on organic solvents. Addition of the paste has no impact on hardener application process.

Depending on the added amount of paste (1-5% by weight hardener), coatings with different shades of grey can be obtained.

Technical dataColor blackDensity 1100-1200 g/L


4-330-0501 500 ml 12

See TDS of the respective material Add 1–5% pigment paste by weight

Application

– Do not allow to dry on the substrate being treated– Remove any remaining residue with a cleaning cloth

BLACK LABEL SERIES

19catalogue

BLACK LABEL SERIES

Prepare the surface according to main material application instructions

While applying a 2K filler, use the following mixing ratio:- filler 100%vol.- hardener 25%vol.- accelerator max. 18%vol.While applying a 2K clearcoat, use the following mixing ratio:- clearcoat 100%vol.- hardener 50%vol.- accelerator max. 8%vol.

Do not use fast and extra fast hardeners while mixing accelerator with clear coats as it will lead to opacity and coat adhesion decrease.

Apply according to main material application instructions.

See main material application instructions.

Density 900 g/L

Application

Further treatment

Technical data

Accelerator


7-830-1000 1 L 12

Description Special additive for accelerating the drying of two-component (2К) fillers and clear coats. In case of clear coats, the accelerator is to be used with standard and slow hardeners. The product saves approximately 15% of drying time.

SubstratesWaterborne and solvent born basecoats, OEM coatings.

20catalogue



Application*

Further treatment

Technical data

Storage

Color yellowDensity 1830 g/L



Pot life: 3–5 min at 20°С


With P80–180




Multi Putty


2-210-2000 2 kg, w/hardener 6

Description Two component multifunctional fine-grained polyester putty for filling unevenness especially on aluminum and galvanized surfaces.

Application Multifunctional finishing putty for eliminating car and commercial vehicle body imperfections.

Characteristics• It is characterized by easily work in thick and thin layers • It can also be used as finishing putty • After drying it produces a smooth, pin-hole free surface • Does not clog the sandpaper • Intended for manual/machine dry sanding.

SubstratesSteel, galvanized surfaces, aluminum, fiberglass plastics, polyester materials, OEM substrates*.

PUTTIES

21catalogue



Application*

Further treatment

Technical data

Storage

Color yellowDensity 1900 g/L





With P80–180




Soft Putty


2-120-0500 0.5 kg, w/hardener 24

2-120-1000 1 kg, w/hardener 12

2-120-1800 1.8 kg, w/hardener 10

Description Two component polyester putty Soft is extremely easy to apply and adopts any desired shape regardless of the material coat thickness. Perfect solution for eliminating car and commercial vehicle body imperfections.

Application For eliminating car and commercial vehicle body imperfections.

Characteristics• Suitable for dry sanding by machine or by hand• Optimal viscosity/plasticity ratio ensures uniform material application • Fast drying prevents clogging of the sandpaper.

SubstratesAll kinds of steel, fibers plastics, OEM substrates*.

PUTTIES

22catalogue


Glass Putty


2-140-0500 0.5 kg, w/hardener 24

2-140-1000 1 kg, w/hardener 12

2-140-1800 1.8 kg, w/hardener 10

Description Two component fiberglass-filled putty. Once dry fiberglass makes the putty highly durable. The product has an excellent adhesion to sanded metal. The putty is used in car and commercial vehicle repair for filling cracks, small holes and areas damaged by corrosion.

Application Fiberglass putty for eliminating car and commercial vehicle body imperfections.

Characteristics• High stability• Limited sanding.

SubstratesAll kinds of steel, aluminium, fiberglass plastics*.


Add 2 – 3% BPO Hardener by weight

Pot life: 3 – 5 min at 20°С

16 – 30 min depending on ambient temperature

With P80 – 180

With P80 – 320 (intermediate sanding step of 100 grit should be observed)


Color greenDensity 1750 g/L


Application*

Further treatment

Technical data

Storage

PUTTIES


23catalogue

PUTTIES

Plastic Putty


2-160-0500 0.5 kg, w/hardener 12


Description Two component high-plasticity polyester putty for plastic parts repair. Excellent adhesion to plastics, fast drying and easy sanding.

Application For repairs on plastic parts of cars and commercial vehicles.

SubstratesAll kinds of plastic:– ABS (acrylonitrile-butadiene-styrene copolymer)– EP (epoxides/laminates)– PA (polyamide)– PBTP (polybutylene terephtalate)– PC (polycarbonate)– POM (polyoxymethylene)– PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer)– PPO (polypropylene oxide)– PUR (polyurethane) soft and hard – PVC (polyvinyl chloride).

Substrates to be treated must be cleaned, dried, degreased (e. g. with C.A.R.FIT Silicone Remover) and treated with suitable matting materials




With P80–180



Application*

Further treatment


Color greyDensity 1858 g/L

Technical data

Storage

• Substrate to be treated must be thoroughly cleaned, degreased and dried• Prior to putty application, the substrate must be sanded/treated with matting abrasives.

Remove all old materials that have poor adhesion or have not fully dried.• Do not apply this product on thermoplastic coatings or etch/acid primers• Prior to application, mix well with a hardener/catalyst• Apply at a temperature no lower than +10°C.

24catalogue

PUTTIES


• Do not apply on etch primers, epoxy primers and fillers• If necessary, use only waterborne epoxy primers

• Add 3.5% CHP Hardener for Spray Putty• Mix well prior to application

Ready for use

Pot life: 3–5 h at 20°C

- Flash-off at 20°C: 10 -15 min - Full drying at 60°C: 30 min




Application*

Further treatment

Technical data

Storage


Spray Putty


2-250-1200 1.2 kg, w/hardener 12

Description Two component polyester putty for filling surface irregularities, sanding marks and pinholes on car and commercial vehicle body parts as well as on vehicle structural components.Good adhesion to metals, wood, polyester materials and fiberglass plastics.Spray Putty is suitable for leveling small and big surface irregularities. The material dries quickly and creates a smooth pinhole-free surface.In order to achieve a high-quality finishing coating, Spray Putty can be covered with a thin (~ 35 μm) sealing coat of 2К acrylic or 2К epoxy fillers without subsequent sanding.

Application For leveling small and big surface irregularities of car and commercial vehicle bodies.

SubstratesMetal surfaces, polyester putties, fiberglass, wood.

20–30 min at 20°C

2.0–2.5 mm / Inlet pressure: see spray gun manufacturer’s tips

Sand with P120-320

To isolate the substrate and prevent the formation of air bubbles (esp. in high humidity), apply 2К Acrylic Fillers 4:1 / 5:1

25catalogue

2K HS Clearcoat 2:1


7-220-1500 1 L Clearcoat + 0.5 L Standard Hardener 12

7-220-5000 5 L Clearcoat 4

7-320-2500 2.5 L Standard Hardener 4

7-321-2500 2.5 L Slow Hardener 4

7-322-2500 2.5 L Fast Hardener 4


Description Two component High Solid gloss clear coat for partial or complete automotive two-coat paintworks.

Application For two-coat paintworks in car and commercial vehicle refinishing. Suitable for applications in spray booths and preparation areas.

Characteristics• High scratch resistance• Suitable for application on solvent- and waterborne base coats• Good flow • High mechanical durability • UV-resistance / non-yellowing • Good chemical, mechanical and weathering resistance

SubstratesWaterborne and solvent-borne basecoats, OEM coatings.

2:1 with hardener for 2K HS Clearcoat 2:1

15–17 sec, FORD 4 at 20°С

Pot life: up to 1.5 hours at 20°C

1.3 mm / Inlet pressure: see spray gunmanufacturer’s tips

2 normal coats = 50–55 μm dry film thicknessFlash-off between coats: 5 - 10 min


Application

Further treatment

Technical data

Density 960 g/L (clear coat)

PAINTWORKS MATERIALS

SCRATCH RESISTANT




6 - 7 h10 - 11 h5 - 7 days


4 - 5 h8 - 9 h5 - 7 days


8 - 9 h11 - 12 h5 - 7 days


Storage

26catalogue


2K MS Clearcoat 2:1


7-150-1500 1 L Clearcoat + 0.5 L Standard Hardener 12

7-150-5000 5 L Clearcoat 4


7-351-2500 2.5 L Slow Hardener 4


Description Two-component Medium Solid gloss acrylic clear coat for two-coat finishes in partial and complete vehicle refinish.

Application For two-coat industrial paintworks.

Characteristics• Special finish for industrial use • Suitable for application on solvent- and waterborne base coats• Good flow • High mechanical durability • UV-resistance / non-yellowing • Good chemical, mechanical and weathering resistance


2:1 with hardener for 2K MS Clearcoat 2:1


Pot life: up to 1.5 hours at 20°C

1.3 mm / Inlet pressure: see spray gun manufacturer’s tips

2 normal coats = 40–45 μm dry film thicknessFlash-off between coats: 5 min


Application

Further treatment

Technical data

Density 960 g/L (clear coat)


INDUSTRIAL USE




6 - 7 h10 - 11 h5 - 7 days


4 - 5 h8 - 9 h5 - 7 days


8 - 9 h11 - 12 h5 - 7 days


Storage

27catalogue


2K UHS Clearсoat


7-115-1000 1 L Clearcoat 12

7-115-5000 5 L Clearcoat 4

7-315-0500 500 ml Standard Hardener 12


7-317-0500 500 ml Fast Hardener 12


VOC: 420 g/LEU limit value: 2004/42/IIB(d)(420)

Description Two component Ultra High Solid gloss clear coat for partial or complete automotive two-coat paintworks.


Characteristics• Easy application • Excellent flow • Deep gloss • High mechanical durability• Yellowing resistance • Can be polished in 60 minutes after cooling.


Ready for use


• Ready for use products are applied at a temperature higher than 15°C• Too thick layers can have negative influence to drying time and level of gloss


1.5–2 normal coats = 50–60 μm dry film thicknessFlash-off between coats: 10 min

Dry through at 20°C: 14–18 h

2:1 with Hardener for 2K UHS Clearcoat + 0-5% C.A.R.FIT Universal thinner

Application

Further treatment

Technical data

Density ca. 990-1050 g/L (clear coat)


Standard10 min30 min

Fast10 min25 min

Can be polished 60 min after cooling


Storage

28catalogue



Application

Further treatment

Technical data

Thoroughly clean and degrease surfaces with C.A.R.FIT Silicone Remover. Sand old finishing coating wet or dry with P800-P1000 abrasive. Clean and degrease surfaces with C.A.R.FIT Silicone Remover once more.

Apply basecoats according to the technical data sheet

Apply the clear coat within 20 min after application of the base coat

Shake can thoroughly before use at least for 2 minutes

Apply 2-3 normal, even coatsAllow 5-10 minutes flash-off time between coats

Allow 30 minutes before handling

Color colorlessDensity ca. 900 g/L

This is a pressurized container, do not expose to direct sunlight or store above 35°C


1K Acryl Clearcoat Spray


7-210-0500 500 ml 12

Description One component gloss clear coat for spot repair of automotive two-coat paintworks.

Application For spot repair in car refinishing.

Characteristics• Easy application• Fast drying• Very high gloss finish• Excellent UV resistance• Blends easily with existing 2K clear coating• High performance clog-free aerosol can.


Drying time depends on film thickness, air humidity and temperature

Storage

29catalogue

Substrates to be treated must be cleaned, dried, degreased (e. g. with C.A.R.FIT Silicone Remover) and treated with suitable matting materials

12–15 sec at 20°C, RFU


1 coat = 3–5 μm

Ambient conditions:- temperature: no lower than +10°С- relative humidity: no more than 75%

10 min at 20°C


Color colorless, with metallic pigmentDensity 894 g/L


4-350-1000 1 L 12


Description One component transparent primer for almost all kinds of plastic, designed to improve the adhesion of refinishing materials to the substrate.

Application For priming plastic parts prior to application of subsequent materials in car and commercial vehicle refinishing.

CharacteristicsContains a metallic pigment for controlling the process of application.

SubstratesABS (acrylonitrile-butadiene-styrene copolymer), EP (epoxides/laminates), PA (polyamide), PBTP (polybutylene terephtalate), PC (polycarbonate), POM (polyoxymethylene), PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer), PPO (polypropylene oxide), PUR (polyurethane) soft and hard, PVC (polyvinyl chloride), OEM coatings.


Application

Further treatment

Technical data

Storage

Recoat with 2К Filler and finishing coating

1K Plastic Primer


30catalogue


Plastic Primer Spray


7-355-0500 500 ml 12

Description 1K ready for use adhesion promoter in an aerosol can. The plastic primer improves the adhesion of paint, adhesives or sealants to the most of car plastics.


Characteristics• Easy application• Fast drying• May be overpainted with the most of paint systems• High performance clog-free aerosol can.

SubstratesMost of plastics, polyester bodyfiller, sanded G.R.P, old/OEM paintworks


Application

Further treatment

Technical data

Storage


Thoroughly clean and degrease surfaces with C.A.R.FIT Silicone Remover

Shake can thoroughly before use at least for 2 minutes

Apply 2 light coats from a distance of 20-30 cmFlash-off between coats: 5 min

Drying at 20°C: 30 min


Overpaints with proper primer/filler or/and topcoat after drying



Drying at 60°C: 15 min

31catalogue


Hi-Build Filler Spray


4-310-0500 450 ml 6


Description 1K ready for use high build filler in an aerosol can. Used for priming uneven surfaces before top coating. Filler is capable of producing a coating film thickness similar to that of a spray gun applied primer.


Characteristics• Easy application• Fast drying• May be overpainted with the most of paint systems• High performance clog-free aerosol can.

SubstratesMost plastics, polyester bodyfiller, sanded G.R.P, old/OEM paintworks


Application

Further treatment

Technical data

Storage

Color greyDensity ca. 900 g/L

Thoroughly clean and degrease surfaces with C.A.R.FIT Silicone Remover

Shake can thoroughly before use for a minimum of 2 minutes

Apply 2-3 normal even coats from a distance of 20-30 cmFlash-off between coats: 5 min

Drying before sanding and overcoating at 20°C: 60 min


Overcoats with proper primer/filler or/and topcoat after drying


Drying before sanding and overcoating at 60°C: 15 min

Dry sanding: with P320–500Wet sanding: P800–1000

32catalogue

Pot life: 1–2 hours at 20°C

1.5–2.2 mm / Inlet pressure: see spray gunmanufacturer’s tips

1 – 3 normal coats60 - 80 μm per 1 coatFlash-off between coats: 7 - 10 min

Sand with P360-500



4:1 by volume with Hardener for 2К HS Acrylic Filler 4:1


Color grey black whiteDensity 1550 g/L 1480 g/L 1580 g/L

10–20% Universal Thinner

3–5 h at 20°C

- Flash-off: 10 min at 20°C- Through drying: 20–30 min at 60°C

- Flash-off: 10 min at 20°C - Medium- / short wave infrared drying: 12–15 min


Application

Further treatment

Technical data

VOC: 520 g/LEU limit value: 2004/42/IIB(c)(540)

2К HS Acryl Filler 4:1


4-100-0800 0.8 L Filler grey + 0.2 L Hardener 12

4-101-0800 0.8 L Filler black + 0.2 L Hardener 12

4-102-1000 0.8 L Filler white + 0.2 L Hardener 12

4-200-3600 3.6 L Filler grey 4

4-201-3600 3.6 L Filler black 4

4-202-3600 3.6 L Filler white 4

4-210-0900 0.9 L Hardener 12

Description 2К HS Acryl Filler 4:1 is the two component high solid filler with very good filling properties. Application of even 3 thick coats of the filler provides good sanding properties due to its good flow. The filler has resistance to runs even if applied with 1.5 - 2.2 mm nozzle. 2К HS Acryl Filler 4:1 is extremely safe to treat even if thick layers are applied.

Application Suitable for large panels covered with polyesters body putties during vehicle repair

Characteristics• Very good filling properties • Fast drying • Wet and dry sanding • Provides excellent corrosion protection and optimum adhesion

SubstratesAll kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings.



Storage

33catalogue



6:1 by volume with Hardener for 2K Acryl Filler Wet-on-Wet

Pot life: 19 sec, FORD 4 at +20°С

1.2 mm / Inlet pressure: see spray gunmanufacturer’s tips1 normal coat = 30 μm

Recoat after 15–20 min at 20°C

1.6–1.8 mm / Inlet pressure: see spray gunmanufacturer’s tips1–2 normal coats = 60–120 μmFlash-off between coats: 5 - 7 min

- Flash-off at 20°C: 5 - 7 min- Drying through at 60°C: 20 min


Sanding: after 3–4 h at 20°C


Preparation

Further wet-on-wet treatment

Technical data

Further treatment with intermediate sanding

Pot life: ca. 60 min at 20°C

Recoat with both waterborne / solvent-based topcoats

With P360–500


2K Acryl Filler Wet-on-Wet


4-300-1050 0.9 L Filler + 0.15 L Hardener 12

VOC: < 540 g/LEU limit value: 2004/42/IIB(c)(540)

Description Acrylic filler 6:1 is used in the repair of damaged and new body parts. The product is applied wet on wet or as a sandable filler. Once the filler has dried completely, it can be wet or dry sanded manually or by machine. This method is suitable for application of polyester putties to repair small or medium damages. When applied wet on wet, the filler efficiently seals the surface to be painted without intermediate drying and sanding. Application For the repair of damaged and new body parts by application wet on wet or with sanding.Characteristics• Very good sealing properties• Overcoatable with both waterborne and solvent-based topcoats• Very good filling properties• Very fast drying.SubstratesAll kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings.

- Flash-off at 20°C: 5 - 7 min- Medium- / short wave infrared drying: 12–15 min


Storage

34catalogue

Description Two component wash primer with excellent anticorrosion properties for auto refinishing.

Application For two-coat paintworks in car refinishing.

Characteristics • Perfect protection of steel surfaces from corrosion • Easy to mix and apply • Excellent flow • Excellent adhesion to different surfaces: steel, aluminum, galvanized steel, polyether putties,

paintworks

Substrates Steel, aluminum, galvanized steel, polyether putties, old finishing coatings in good condition.

2K Wash Primer 2:1


4-398-0800 0.8 L, Primer 6

4-420-0400 0.4 L, Activator 6


Color beigeDensity 950 g/L

Substrates to be treated must be cleaned, dried, degreased with C.A.R.FIT Silicone Remover and sanded.

Steel surface should be first degreased, dry sanded and degreased again. The aluminum and galvanized steel should be degreased, dulled with the abrasive cloth and degreased again.The old coatings should be degreased, dry sanded and degreased again.

Following sandpaper gradations are recommended:

- by hand (dry or wet): P280÷P320- by machine (dry): P180÷P220

• Do not exceed recommended doses of activator!• The best repair results you can achieve at room temperature. Temperature in body shop and

temperature of a product should be the same.• When working with 2K products, clean the guns and equipment immediately after use.• Do not apply polyester putties and acryl topcoats directly on 2K Wash Primers

2:1 with Activator for 2К Wash Primer 2:1Primer is ready to apply after 10÷15 min from mixing with activator!

18–20 sec at 20°C ca. 48 h at 20°C


1.5 - 2 coatsFlash-off between coats: 5 min

- Flash-off at 20°C: ca. 15 min- Recoat with 2К Acryl Fillers and finishing coatings- Recoat with Stone Chip Protection

Substrate preparation

Application

Storage

Technical data

Further treatment



35catalogue


2K Epoxy Primer 1:1Description High quality two component epoxy primer can be used as an insulation coating. 2K epoxy primer 1:1. It is specially recommended to apply the product wet on wet. Application For two-coat paintworks in car refinishing. Characteristics • Perfect protection of steel surfaces from corrosion due to anticorrosion additives • Easy to mix and apply • Easy to overcoat due to light-grey color • Excellent flow • Excellent adhesion to different surfaces: steel, aluminum, galvanized steel, fiberglass,

polyether and epoxy putties, wash primers, paintworks Substrates Steel, aluminum, galvanized steel, polyether laminates GFK/GRP, polyether / epoxy putties, 2K primers, old finishing coatings in good condition.


4-390-0500 0.5 L, Primer 6

4-415-0500 0.5 L, Hardener 6

Color light greyDensity 1560 g/L

All substrates must be cleaned, dried, degreased with C.A.R.FIT Silicone Remover and sanded.Steel surface should be degreased, dry sanded and degreased again.The aluminum and galvanized steel surfaces should be degreased, sanded and degreased again.The old coatings should be degreased, dry sanded and degreased again.The following abrasives are recommended: - by hand (dry or wet): P280÷P320; - by machine (dry): P180÷P220.

- 1:1 with Hardener for2К Epoxy Primer 1:1- Pot life at 20°C: ca. 3 h

• Do not exceed recommended doses of hardener!• The best repair results you can achieve while working at room temperature. • The temperature in a body shop and the temperature of a product should be the same.• When working with 2K products, clean spray guns and equipment immediately after use.

18-20 sec, FORD 4 at 20°С


5 h at 20°C

2 – 3 layers = 100 – 140 μm Flash-off between layers: 5 – 10 min

Overcoats with 2К acrylic fillers, 2K epoxy fillers or / and refinishing materials.

- Flash-off at 20°C: ca. 10 min - Drying at 60°C: 35 min

- Sanding dry P400-500- Sanding wet P800-1000

- Flash-off at 20°C: ca. 10 min - Short wave IR drying: 15 – 20 min (at 100-140 μm dry coat thickness)

Substrate preparation

Preparation

Technical data

Intermediate sanding application and treatment


1.4–1.7 mm / Inlet pressure: see spray gun manufacturer’s tips1.5 – 2 layers = 20 – 25 μm Flash-off between layers: 5 – 10 min

Flash-off at 20°C: ca. 45 - 60 min depending on dry coat thickness

Storage


Further treatment

Wet-on-wet application and treatment

36catalogue

Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings

– Clean the substrate with C.A.R.FIT Silicone Remover – Apply with a spray gun, a cloth or a sponge

– Do not allow to dry on the substrate being treated– Remove any remaining residue with a cleaning cloth


Application


Application


See TDS of the principal material

Universal Thinner


7-600-1000 1 L 12

7-600-5000 5 L 4

Description Product for thinning all kinds of C.A.R.FIT refinishing materials.

Application Thinning of primers, fillers and clear coats in car and commercial vehicle refinishing.


Technical dataDensity 900 g/L

Silicone Remover


7-500-1000 1 L 12

7-500-5000 5 L 4

VOC: 790 g/LEU limit value: 2004/42/IIB(a)(850)

Description Cleaning compound based on low volatile organic solvents for initial cleaning of old/OEM coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product.

Application Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish.


Technical dataDensity 740–790 g/L

THINNERS, CLEANERS

37catalogue

THINNERS, CLEANERS

Fade Out Spray


7-555-0500 500 ml 6


Description Fade Out Spray is a special thinner for fast, simple, accurate dissolving of edges of 2K Clearcoat repairs.It increases efficiency of the fade out process to give an invisible blend. Using this product in partial coating repair provides a result of a smooth fade out between old and new coatings.

Application For paintwork repair in car refinishing.

Characteristics• Easy application• Fast drying• Ideal for use with both MS and HS Clearcoat• UV stable• High performance clog-free aerosol can.

SubstratesRefinish clear coats, old/original and OEM paintworks.


Application

Further treatment

Technical data

Storage


Apply base coat and then clear coat according to TDS

Shake can thoroughly before use for a minimum of 2 minutes

Once the clear coat has been applied a light mist coat Fade Out Spray is applied over the blend area holding the aerosol 25cm from the panel.

The blending process is best undertaken in two rapid light passes of the aerosol. The blend edge will melt into the original paintwork requiring little or no processing once the clear coat has cured.

Fade Out Spray is used when blends or spot repairs operations are being carried out; all these processes result in an interface being created between the existing, curedcoating and the freshly applied clear coat.If the interface is not treated a dry edge will be visible upon cure of the fresh coating

Once applied the clear coat manufacturer’s instructions for flash off and air/force dry should be followed


38catalogue

Rubbing Compound


5-100-0500 500 ml 10

Description Polishing paste without silicone for removing sanding marks left on fresh and old coatings by manual or machine sanding with P1500-2000 grit abrasives.

Application Polishing of car and truck coatings.

CharacteristicsHigh efficiency abrasive based on aluminium oxide.

SubstratesOld/OEM or fully cured fresh refinishing coatings.

The substrate must be thoroughly cleaned of dust using a sponge with water and degreased with degreasing compounds.

1. Fresh and fully cured paintworksUse a woolen polishing pad.Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result.After manual sanding with abrasive paper, especially on dark surfaces, repeated polishing may be necessary.Once almost all the paste has been used up, increase the RPM of the sander for better clean-ing of the surface.For higher shine and deeper color, repeat the operation with a yellow foam polishing pad until complete removal of fine scratches left by the woolen polishing pad.

2. Old paintworksUse a foam polishing pad.Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result.Once almost all the paste has been used up, increase the RPM of the sander for better clean-ing of the surface.

• Apply the product onto the surface, not the polishing pad!• Mask plastic parts in advance to avoid their contamination• Avoid overheating of the surface• A few minutes after polishing, remove the compound residue with a microfiber cloth.


Application

Storage

POLISHING MATERIALS

39catalogue

Woolen Polishing Disc Velcro

Woolen polishing discs with self attachment Velcro system. To be used with Universal Polishing Paste.

Foam Polishing Disc VelcroFoam polishing discs with self attachment Velcro system.


5-100-0150 Diam. 150 mm 1

5-100-0180 Diam. 180 mm 1


5-100-0161 Hard, diam. 150 mm, yellow 1

5-100-0162 Medium-Hard, diam. 150 mm, orange 1

5-100-0163 Soft, diam. 150 mm, black 1

Pad for Polishing Disc Velcro

Velcro foam polishing pad for finish polishing jobs.


5-100-0001 For disc diam. 180 mm, M14 1

5-100-0002 For disc diam. 150 mm, M14 1

POLISHING MATERIALS

40catalogue

Stone Chip Protection


5-600-1000 1 kg bottle, black 12

5-601-1000 1 kg bottle, grey 12

Description Synthetic resin-based stone chip protection of vehicle underbody and lower body. The coating can be primed or overpainted in any color within 30-40 minutes after drying. The coating has high durability and excellent resistance to abrasive wear. It also has sound deadening and vibration absorbing properties. Application For treatment of car and commercial vehicle bodies.

Characteristics• Supplied in a bottle–always ready for use • Recoatable• Produces a durable coating that is resistant to abrasive wear and aggressive chemicals • Sound deadening and vibration absorbing properties.

SubstratesVarious metal surfaces, primed metal parts, old/OEM coatings.

Clean carefully the substrate from rust. Degrease with C.A.R.FIT Silicone Remover

Do not apply on engine, brake system and exhaust pipe

1 – 2 layers150 – 200 μm per one layerFlash-off between layers: 5 – 10 min

- Recoat at 20oC: 30-40 min - Tack free at 20oC: 1.5 h


Application

Technical data

Color black / grey / whiteDensity 1450 ± 50 g/L


PROTECTINE COATINGS

Shake well before use for about 3 min

Ready for use

Avoid any mechanical solicitation to the treated parts before 24 hours (for example: car wash with high pressure hot water)

Apply with a pneumatic sprayer at a spray pressure of 3–4 bar

Further treatment

Do not expose to direct sunlight or store above 35°C

Storage

41catalogue

PROTECTINE COATINGS

Do not apply on walls that have already been exposed to overspray and other materials

Viscosity as supplied = application viscosity (RFU)

1.5 - 1.8 mm/ Inlet pressure: see spray gunmanufacturer’s tips

1–2 coats = 75–95 μm(pneumatic spraying)Flash-off between layers: 5 - 10 min

Apply a uniform thin coat with a brush

Color colorlessDensity 1024 g/LCoverage 8–10 m2/L

Remove with a sponge and water


Application

Further treatment

Technical data

Storage

Apply a uniform thin coat with a roller

Refer for consultation of airless spray equipment manufacturer

Depends on the coat thickness of the material being applied. For best results, we recommend to apply the material in 1-2 coats with a 20 min flash-off between the coats. Two coats ensure durable protection with no risk of the coating being washed away.

All tools used for the application of the coating must be thoroughly washed with water.If the temperature inside the spray booth is 70–90°C, the coating should be renewed more often: at least once a month. This will prevent the protective film from drying up.If necessary, several new layers can be applied on the old film.In case of a long operation life of the spray booth, it is recommended that the old protective film should be removed prior to application of a new one.

Tack Coating for Spray Booth


3-400-0010 10 L 1

Description Booth mask safely binds paint, dust and overspray particles that tend to settle on spray booth walls and ceiling panels, thus preventing contamination of the surface being refinished. The compound stays transparent and water-soluble. Thin and sticky protective film never dries out on the wall, ensuring safe dust and overspray binding. Once the film loses its particle-binding capacity, it can be easily washed off with water and a sponge and then reapplied.

Application For overspray and dust protection of spray booth walls.

Characteristics• Provides dust protection of the object being refinished• Protects spray booth surfaces from paint, dust and overspray• Specially designed to protect glass and lights without impacting light permeability and reflection capacity• Easy to apply and remove • Very cost-effective. Depending on the level of contamination, the coating should be replenished once in

a few weeks• 100% environmentally-friendly.

SubstratesAluminium, steel and galvanized walls of spray booth cabins; fully cured and clean paintworks.

Removal

TACKy COAT

42catalogue


Application

Technical data

Storage

Clean and degrease surfaces with solvent like acetone. Oxidized metal surfaces and concrete must be first sanded and then cleaned. Degrease PVC, aluminum and glass with a non greasy solvent, like acetone.

• The temperature of the substrate must be within +5…+40°C• In case of application by cold weather, store the cartridges at 20°C before use• Prior to application, carry out a test on adhesion efficiency and compatibility with each of the materials

upon which the sealant will be applied

Puncture the cartridge and section the nozzle according to the extrusion diameter required, remove the metal base and the dehydrating salts and extrude from cartridge with a manual or pneumatic gun.

Film thickness depends on the characteristics of the materials being bonded.The joint should be overlapped on the previous section; the end-to-end jointis prohibited to avoid the leakage of water.The process of bonding must take no more than 10 minutes.PU sealant has a relatively high viscosity. Therefore, it is advisable to use special clamps for locking the parts being bonded until the sealant dries completely.

Tack free time at 23°C and 50% r.h.: 25-30 min

Store in cool dry place and at temperature < 25°C, avoid sunlight

VOC (grey and black): 125.5 g/LEU limit value: 2004/42/IIB(e)(840)

PU Adhesive and Sealant


5-113-0310 310 ml tube, grey 12

5-115-0310 310 ml tube, black 12

Description PU Adhesive and Sealant is a one-component polyurethane sealant. By reaction with air humidity, the product cures into a strong but flexible rubber, with excellent adhesion to many substrates. It will not sag even when applied in thick layers. The product is resistant to ageing, weather and is impermeable to water.

Application PU Adhesive and Sealant is suitable for sealing all kinds of joints: overlaps, flanges, linear-weldings, spotweldings etc. It is also used to seal drains, lamp housings, reversible roofs and other car body parts.

Characteristics• Excellent adhesion to most rough and treated metal sheet• Once fully cured* the sealer can be recoated with any two component paint materials.

*preliminary tests are recommended prior to application of resin-based paints.

SubstratesVarious metal surfaces, e. g. aluminium, wood, primed substrates, thermoreactive plastic, old/OEM coatings.

ADHESIVES & SEALANTS

Color grey black

Density at 23°C and 50% r.h. 1270 g/L 1240 g/L

Curing through volume (1 day at 23°C and 50% r.h.)

≥ 4 mm ≥ 4 mm

Shore A at 23°C and 50% r.h; DIN 53505 52 52

Tensile strength (ISO 37 DIN 53504) ≥ 2.0 N/mm² ≥ 2.0 N/mm²

Elongation (ISO 37 DIN 53504) ≥ 250% ≥ 250%

Application temperature +5°C...+40°C +5°C...+40°C

Temperature Resistance -40°C...+90°C, briefly at 120°C

-40°C...+90°C, briefly at 120°C

43catalogue


Clean and degrease surfaces with solvent like acetone. Let dry after degreasing.

• The substrates to be bonded must be dry, oil-free, grease-free, dust-free and free of any contaminating agents that could harm bonding.

• In cold weather, store the cartridges or sausages at a temperature of about 20°C before use.• Do not wipe the substrate up and down. If the pad has got dirty, replace it with a new one and continue the

procedure. If the primer peels off, replace the windshield to avoid unpredictable consequences. • If any deviations in the substrate material are detected, it is advisable to carry out an adhesion test prior to

actual bonding. Test bonding of the windshield with any materials is particularly recommended to achieve desirable adhesion.

• Avoid any contact with non-cured MS, hybrid PU or silicone sealants as well as with alcohols or ammonia during curing.


Application

- Apply the glass coated with the sealant on the car body and press, before the skin formation time (i.e. within 30 minutes).- Apply the glue with a glue gun onto the substrate.- Install the glass onto the window frame and use the palm to press softly till the glass is bound flatly. Adjust the space up and down, left and right, and use the press sensitive tape to fix.- Excessive glue can be removed with a scraper or soapy water.- If any glue residue remains on the substrate, quickly remove it with an alcohol-free cleaning agent, e. g. gasoline. If the glue has hardened, use a blade.

Do not apply at a temperature below +5°C

Tack free time: 15 min at 23°C and 50% r.h.

Store in cool dry place and at temperature 10 - 25 °C, avoid sunlight

Technical data

Storage

Windglass Glue


5-132-0310 310 ml tube, black 12

Description Windglass Glue is a one component, thixotropic, moisture curing polyurethane adhesive, primarily used for automotive direct glazing with and without airbag. It cures in a longer time allowing application on big windscreens such as buses and trucks.

Application Windscreen direct glazing.

Characteristics• Drive Away Time - 2 h (for car fitted with both driver and passenger airbags)• Rapid application and curing• Suitable for cold application• Good stability/workability – no sag• Short cut-off string• High shear modulus• High electrical volume resistivity 1 G Ωxcm• Non-conductive: suitable for use with integral aerials• Prevents contact corrosion in aluminium-body vehicles.

SubstratesVarious metal surfaces, incl. glass, aluminum , ceramic coatings, old/OEM coatings.


Color blackCuring through volume (1 day at 23°C and 50% r.h.) ≥ 4 mmShore A at 23°C and 50% r.h; DIN 53505 55Density at 23°C and 50% r.h. 1360 g/LG modulus at 10% ≥ 2.0 N/mm2

Tensile strength (ISO 37 DIN 53504) ≥ 9.0 N/mm2

Elongation (ISO 37 DIN 53504) ≥ 300%Application temperature +5°C...+40°CTemperature Resistance -40°C...+90°C,

briefly at 140°C

44catalogue

Plastic Repair Kit


2-220-0250 250 g resin + BPO catalyst + glass mat 20

Description Repair kit for restoration of damaged steel and glass reinforced plastic parts and stopping up rust through holes in metal parts. The kit contains polyester resin, BPO catalyst and glass mat.

Application The product is ideal for repair of car structural components, tanks, architectural parts and etc.

Characteristics • Excellent adhesion to steel surfaces• Polyester resin is a thixotropic product which can be easily applied• The resin contains an additive reducing the emission of harmful substances during the

application and drying• The resin formulation is selected in a way that after product hardening its surface is not sticky,

it is very important for sanding.

Substrates Steel, metals, glass reinforced plastics, laminated plastics.


Carefully remove remains of old coating from the surface using P40-80 abrasives and degrease with C.A.R.FIT Silicone Remover

• Follow the BPO catalyst mixing ratio!• Carefully mix• Do not apply on acrylic top coats• Temperature increase can reduce the gel time

- Mix with 2-3 g (2-3%) BPO catalyst- Pot life at 20°C: 5 - 10 min- Gel time at 20°C: ca. 10 min

Dust free at 20°C: 20 minTouch free at 20°C: 30 min Sanding dry with P80–120

Apply the mixture on the surface with a brush or a filling knife, and then apply the glass mat in a way that it covers the surface and goes out of the edge of the area for 5 cm. After that apply the mixture on the glass mat till it gets fully saturated, remove the air bubbles by flat-tening the material with a stiff brush. When the temperature of the resin layer will be approxi-mately equal to the room temperature, the surface can be sanded with P80-120 abrasives. All irregularities are to be eliminated by application of the filling / finishing putty.

1.5-2 kg of resin should be used for 1 kg of glass mat. The subsequent resin layer is to be applied not later than 48 hours after the previous layer application, otherwise the surface is to be sanded as there is a risk of subsequent resin layer breakaway

Store in a cool place


Application

Technical data

Further treatment

Storage

Color light brownDensity 1120 g/L (resin)

45catalogue

Masking Film DispenserThe dispenser allows one person to perform complete vehicle masking.


1-205-0001 Steel 1


1-200-4020 4 m х 200 m, thickness 10 μ 1

1-200-0450 4 m х 5 m, thickness 7 μ 40

1-200-0470 4 m х 7 m, thickness 7μ 40

Masking FilmDescription Semi-transparent polyethylene masking film has good adhesion to refinishing coatings due to its electrostatic charge and is highly resistant to weathering.

Application For quick masking of large vehicle surfaces and parts prior to painting.

Characteristics• Made of high density polyethylene (HDPE)• Heat resistance 10…140°С

SubstratesMetal and plastic parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings.

Material HDPE (High Density Polyethylene)

ELECTROSTATIC EFFECT

Pretaped Masking FilmPolyethylene masking film with an adhesive tape for refinishing works. It prevents overspray from getting onto the surface being treated. The masking film is highly-durable and adheres well to the surface.


1-200-0550 550 mm х 33 m, roll 1

1-200-1800 1800 mm х 33 m, roll 1

1-200-2700 2700 mm х 20 m, roll 1

MASKING

46catalogue

Masking PaperMechanically and waterproof high-quality masking paper for overspray protection of vehicle surfaces that are not subject to refinish. Due to special treatment, one of the sides has a smooth, lint-free and pinhole-free surface ensuring high quality repair. Density 40 g/m2.


1-230-1520 150 mm х 200 m, roll 1

1-230-6020 600 mm х 200 m, roll 1

1-230-8520 850 mm х 200 m, roll 1

1-230-1320 1300 mm х 200 m, roll 1WATERPROOF

Mobile Masking Paper DispenserDispenser accommodating 3 separate rolls of masking paper at a time, fitted with masking tape-removing rollers. Perfect solution for fast and cost-saving masking to provide overspray protection to vehicles.


1-225-0001 Steel 1

Masking Tape 80°С


9-100-0019 width 19 mm, thickness 90 ± 15 μm

48


36


24


18

Tensile strength 50 ± 15 N/mm2

Elongation at break 9 ± 2 %

Description Masking tape made of impregnated crepe paper has excellent elongation characteristics and high initial adhesion strength provided by natural rubber. The product is suitable for masking jobs for sanding as well as for application of waterborne or solventborne refinishing materials with subsequent drying in a spray booth. Once the refinishing coating has dried, the masking tape comes off cleanly and leaves no residue.Application Vehicle body protection from overspray during refinishing.SubstratesMetal parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings.

Technical Data

Adhesion 4.5 ± 1 N/25 mm

Tack test < 3 cm

MASKING

47catalogue

Classic Foam Masking Tape Classic foam tape for masking gaps and apertures in the vicinity of doors, bonnet, trunk and gas cap lid. The masking tape helps avoid sharp edges in painting and prevents overspray from getting inside the vehicle. The tape is dust and paint-proof that makes the use of passenger compartment protection unnecessary.


9-109-0500 13 mm х 50 m, roll 1

Protective Film for Steering Wheel

Transparent tape for vehicle steering wheel protection during repair. Supplied in roll, without dispenser.


3-110-0150 150 m, roll 1

3-140-0001 dispenser for steering wheel protective film, length 125 mm

1

Seat Cover

Pre-cut polyethylene seat cover for masking vehicle seats during repair. Supplied in perforated rolls for easy tear-off.


3-120-0500 size: 82 cm x 130 cm x 10 μm 500

MASKING

48catalogue

CLOTHS

Car Clean MultiLint-free cloths (w/o dispenser) with a high resistance to oils and solvents for the removal of spilled oil, paint, ink, etc.

Characteristics• Special impregnation for higher absorption capacity• High absorption capacity enables the cloth to absorb 8 times its own weight in liquid• Suitable for cleaning and wiping of equipment, floors, workpieces, etc.• Durable and soft at the same time• Material density: 75 g/m2


8-801-0500 380 mm х 320 mm, rolls 500

8-801-0050 420 mm х 267 mm 50

Double Layer Cleaning ClothHighly durable double-layer lint-free cleaning cloths made of quality embossed crepe paper. Supplied in perforated rolls. Material density: 2x2.22 g/m2


8-802-1000 380 mm х 370 mm, rolls 1000

Microfibre Cleaning Cloth

Woven microfiber cloth for fast and efficient cleaning of the surface without using cleaning agents.

Characteristics• Captures and binds contaminants in a fast and efficient way • Restores the gloss and color of the paintwork • Does not require cleaning agents–cost saving • Reusable after washing• Material density: 300 g/m2


8-803-0002 400 mm х 400 mm, folded 1

49catalogue

CLOTHS

Tack ClothCotton tack cloth for cleaning dust from all kinds of surfaces, including water-based coatings. Does not wrinkle–no need in smoothing out the fabric. Wax and silicone-free.


6-100-0005 80 cm х 50 cm, folded 5

Tack Cloth “Super Wave”

DescriptionTack cloth “Super Wave” easily adopts palm shape, due to which it fits tightly against the surface upon wiping–no need in supplementary devices. Larger area of the surface and, at the same time, a smaller contact zone allow for secure dust binding inside the cloth, regardless of the size of dust particles. The carrier material lets dust easily enter into the inner layers and provides additional security and the highest possible dust absorption capacity.The impregnation of the cloth does not dry out and is compatible with all kinds of refinishing materials.

ApplicationFor dust binding for dust-free sanding and refinishing.

Characteristics• Wavelike surface is hugely important for removing dust from large and even parts• Easily adapts to the surface being treated• Excellently absorbs dust• Glides easily along the surface• User-friendly• No need in supplementary devices.


6-110-0001 80 cm х 90 cm 1

Substrates Metal parts, rubber, glass, chrome-plated surfaces, putties, primers/fillers, OEM/refinishing coatings.

50catalogue

Nitrile Gloves

Characteristics• Finger or palm textured design• No powder lubricant added• Protection from unwanted and dangerous substances• Beaded cuff ensures easy donning and prevent roll down• Biocompatibility tested or biocompatibility friendly• Superior strength with better puncture resistance• Custom design enhances comfort and fit• Provide an alternative solution for individuals who are allergic to natural rubber latex• Conforms to ASTM D6319 and EN455 Standards• Manufactured under QSR (GMP) and IS0 9001 : 2008 Quality Management System.


3-260-0350 palm textured, size M 100

3-260-0450 palm textured, size L 100

3-260-0550 palm textured, size XL 100

Description100% synthetic nitrile rubber gloves with high resistance to widen range of chemicals as compared to natural rubber latex of the same thickness.The gloves efficiently prevent non-organic and grease contaminants from getting onto the paintwork. The product complies with the standard EN 455-1/2/3.

ApplicationUse for protect the skin during the preparation work, especially at mixing- or preparation of paints, in order to avoid skin irritations.

Paint CoverallLight and comfortable paint overall made of processed cellulose impregnated with polyethylene which makes it more durable and prevents skin exposure to liquid and aerosol materials.The overall is outfitted with a zip fastener and elastic cuffs on sleeves, pant legs and hood for overspray protection.


3-265-0001 size L 1

3-265-0002 size XL 1

ACCESSORIES

51catalogue

SCR Mixing Cup SystemDescriptionSCR System it is a new mixing cup system for painting, refilling and storing of paint material. SCR System is a disposable cup fully complying with the requirements of professional painters and bodyshops.SCR System includes 4 components: cup – lid – sieve – adapter.


3-230-0001 lid for 0.75 L mixing cup 40

3-230-0125 sieve 125 μ 40

3-230-0200 sieve 200 μ 40

Adapters for spray guns:

3-230-1002 SATA jet 2000 / RP / 90 / KLC 1

3-230-1004 SATA jet 2000 / 3000 / 4000 / 5000 with QCC

1

3-230-1009 Iwata W400 / WR400 / AZ3 THE / LPA94 / VXL Primer

1

3-230-1014 Devilbiss GTi Pro / PRi 1

Characteristics• A really simple and quick preparation of paint material• The usual working method and perfect results for paint work• Easy color change• Great solvent savings (up to 86 % possible)• Simply throw away after use• Significantly increased productivity of up to 46 %• SCR System offer widen range adaptors for spray guns of different manufacturers • Clean refilling and safe storing of paint material remainders.

Mixing CupHigh-quality solvent proof plastic cups with lids designed for mixing of paintwork materials with hardeners and thinners in different ratios. The cups are produced on modern industrial equipment. The cups are notable for high quality plastic and molding, for clean surface having no oil residues and for accuracy and durability of the printed graphical information.It has a high quality mixing ratio scale applied, this allows one to mix materials in the following volume ratios 2:1, 3:1, 4:1, 5:1, 6:1, 7:1 and general scale.


3-200-0385 cup 0.385 L 200

3-200-0750 cup 0.750 L 200

3-200-1400 cup 1.4 L 200

3-200-2300 cup 2.3 L 100

3-223-0385 lid for cup 0.385 L 200

3-223-0750 lid for cup 0.750 L 200

3-223-1400 lid for cup 1.4 L 200

3-223-2300 lid for cup 2.3 L 200

ACCESSORIES

52catalogue

Set of dispensersfor mixing cups

Set of metal wall-mounted dispensers for mixing cups with a capacity of 0.385 l, 0.75 l, 1.4 l and 2.3 l. Durable chromium coating of dispensers provides mechanical resistance. The set includes fastening elements.


3-223-0004 Set of 4 dispensers 1

Disposable Paint StrainerPaper filter with an insert made of artificial material for filtering paint and similar materials based on organic solvents. The strainer efficiently removes foreign particles that can get into refinishing materials and cause spray gun clogging.


7-850-0125 125 μm 1000

7-850-0190 190 μm 1000

Metal Test CardMetal test card with size 105x150 mm for testing automobile paints prior to application. Suitable for application of solventborne, and waterborne paints.


7-700-0100 white 100

7-700-0200 grey 100

7-700-0300 dark grey 100

ACCESSORIES

53catalogue

Pump SprayThe sprayer with an air pump is intended for spraying silicone removers and thinners/cleaners. It is made of plastic that is resistant to said materials.


3-255-0001 1 L 1

Touch Up Bottle Customer hand out unbreakable and transparent bottle with a brush for spot repairs, such as stone chip damages.Solvent resistant. Includes mix-ball.


3-115-0001 set in box 100

Tape-off Disс Premium88- mm rubber discs for removing adhesive tapes, glue residues, etc. It is supplied with a screwfor a collet chuck adapter.


3-150-0300 2 discs + 1 adapter 1

ACCESSORIES

54catalogue

Flat Sanding BlockSanding block with a flat working surface for manual sanding of small and inaccessible areas.


5-170-0005 70 x 198 mm 1

Semi-Round Sanding BlockSanding block with a semi-round working surface for manual sanding of small, complex-shaped and inaccessible areas.


5-170-0006 70 x 198 mm 1

Sanding Block for150-mm Abrasive Disc

Manual sanding block for 150-mm abrasive discs.


5-170-0001 Polyurethane, Velcro 1

ACCESSORIES

55catalogue

Rubber Sanding BlockRubber block for sanding works.

Manual Polishing & Sanding PadVelcro back-up pad for polishing and sanding discs.


5-170-0004 Polyurethane, for 150 mm discs 1


5-170-0002 Rubber, 67 х 125 mm 1

Sanding Control Powder


5-200-0100 black powder 1

Description The quick and most cost effective system for highlighting imperfections such as pinholes and scratches in filler and primer and ensures body work is flat and body styling contours are true prior to final coat application.

Application

Use for sanding operation control in car refinishing.

Characteristics • No masking required• Easy to apply• Non-solvent based• Full coverage to repair area• No dry time required• Instant defect detection• No aerosol / spray gun required• No risk of applicator plugging• Perfect for either wet or dry sanding.

Substrates OEM / refinish primers and fillers.

ACCESSORIES

56catalogue

Rotating Paint StandMultipurpose rotating paint stand with spray gun holders and a set of fixtures for extensions. The paint stand provides aid in refinishing car doors, bonnets, trunk lids, etc.


3-100-0001 With 6 extensions 1

Folding Paint Stand PremiumFolding stand for securing the workpiece in a convenient position for the painter. The stand is very stable and accommodates bulky and heavy parts.


3-105-0001 With 2 additional fasteners 1

ACCESSORIES

57catalogue

NOTE

58catalogue

NOTE

August Handel GmbHSeestraße 33 Brandenburg Park14974 Ludwigsfelde (Berlin)

Phone: +49 3378 / 20333-0Fax: +49 3378 / 20333-19E-mail: [email protected] 03/2016

2016 - carfitrepair.com · steel, aluminum, galvanized steel, fiberglass *. substrates to be...

Documents