Operating Instructions & Parts Manual EN

16” and 18” Scroll Saws

Models 38UK50 and 38UK51

9639009.01

PLEASE READ AND SAVE THESE INSTRUCTIONS.

READ CAREFULLY BEFORE ATTEMPTING

TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE

PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL

SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS

COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

PLEASE REFER TO BACK COVER FOR INFORMATION REGARDING

DAYTON’S WARRANTY AND OTHER IMPORTANT

INFORMATION.

Model #: ___________________

Serial #: ___________________

Purch. Date: _______________

© 2016 Dayton Electric Manufacturing Co.All Rights Reserved

3

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

GETTING STARTED

Structural requirements

Make sure all supporting structures and load attaching devices are strong enough to hold your intended loads. If in doubt, consult a qualified structural engineer.

Electrical requirements

The power supply to the Scroll Saw needs to be 120 volt/1.2 amp, single phase, 60 Hz. The standard allowable voltage variation is a plus or minus 10%.

Tools needed:

Standard mechanic’s hand tool set.

UNPACKINGCarton should be handled with care to avoid damage from dropping, bumping, etc. Store and unpack carton with correct side up. After unpacking Scroll Saw, inspect carefully for any damage that may have occurred during transit. Check for loose, missing or damaged parts. If any damage or loss has occurred, claim must be filed with the carrier immediately. Check for completeness. Immediately report missing parts to dealer.

The Scroll Saw comes assembled as one unit. Additional parts which need to be fastened to the Scroll Saw should be located and accounted for before assembling.

IMPORTANT: The tool has been coated with a protective coating. In order to ensure proper fit and operation, the coating must be removed. Remove coating with mild solvents such as mineral spirits and a soft cloth. Nonflammable solvents are recommended. After cleaning, cover all exposed metal surfaces with a light coating of oil.

Never use highly volatile solvents. Avoid getting cleaning solution on paint as it may tend to

deteriorate these finishes. Use soap and water on painted components.

Contents:

• Scroll Saw (1)

• Wrenches (4)

• Blade (1)

• Pinless blade holder (2)

• Operating Instructions and Parts Manual (1)

Unpack

• Open carton and carefully remove Scroll Saw from packaging material. Do not discard packing materials

until after machine has been inspected for damage and completeness. Locate loose parts and set aside.

Inspect:

• After unpacking the unit, carefully inspect for any damage that may have occurred during transit. Check for loose, missing or damaged parts. Shipping damage claims must be filed with the carrier.

• All tools should be visually inspected before use, in addition to regular periodic maintenance inspections.

• Be sure that the voltage labeled on the unit matches your power supply.

• See General Safety Instructions, Cautions and Warnings as shown.

SAFETY RULESFor your own safety, read all of the instructions and precautions before operating tool.

PROPOSITION 65 WARNING: Some dust created by using power tools contain chemicals known to the state of California to cause cancer, birth defects or other

reproductive harm.

Some Examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.

Always follow proper operating procedures as defined in this manual even

if you are familiar with the use of this or similar tools. Remember that being careless for even a fraction of a second can result in severe personal injury.

Be prepared for the job

• Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught up in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear safety glasses complying with United States ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are not safety glasses.

• Wear face mask or dust mask if operation is dusty.

• Be alert and think clearly. Never operate power tools when tired, intoxicated or when taking medications that cause drowsiness.

Prepare work area for job

• Keep work area clean. Cluttered work areas invite accidents.

MA

INTE

NA

NC

E / R

EPA

IRTR

OU

BLE

SHO

OTI

NG

OPE

RAT

ION

ASS

EMB

LY /

INST

ALL

ATIO

NSA

FETY

/ SP

ECIF

ICAT

ION

SG

ETTI

NG

STA

RTE

D

4

SAFETY RULES (CONTINUED)• Do not use power tools in dangerous environments. Do not

use power tools in damp or wet locations. Do not expose power tools to rain.

• Work area should be properly lighted.

• Proper electrical receptacle should be available for tool. Three-prong plug should be plugged directly into properly grounded three-prong receptacle.

• Extension cords should have a grounding prong and the three wires of the extension cord should be of the proper gauge.

• Keep visitors at a safe distance from work area.

• Keep children out of workplace. Make workshop childproof. Use padlocks, master switches or remove switch keys to prevent any unintentional use of power tools.

Tool should be maintained

• Always unplug tool prior to inspection.

• Consult manual for specific maintaining and adjusting procedures.

• Keep tool lubricated and clean for safest operation.

• Keep all parts in working order. Check to determine that the guard and other parts perform their intended function.

• Check for damages parts. Check for alignment of moving parts, binding, breakage, mounting and any other condition that may affect a tool’s operation.

• A guard or other part that is damaged should be properly repaired or replaced. Do not perform makeshift repairs. (Use parts list provided to order repair parts.)

Know how to use tool

• Use the right tool for job. Do not force tool or attachment to do a job for which it was not designed.

• Disconnect tool from power when changing accessories such as blades, flexible shaft and the like.

• Avoid accidental start-up. Make sure that the power switch is in the OFF position before plugging in.

• Remove adjusting tools. Form habit of checking to see that the adjusting tools are removed before switching machine on.

• Do not force tool. It will work most efficiently at the rate for which it was designed.

• Turn tool off if it jams and unplug power cord before removing jam.

• Keep hands away from moving parts and cutting surfaces.

• Never leave a tool running unattended. Turn the power off and do not leave tool until is comes to a complete stop.

• Do not overreach. Keep proper footing and balance.

• Never stand on tool. Serious injury could occur if tool is tipped over.

• Know your tool. Learn the tool’s operation, application and specific limitations.

• Use recommended accessories. Understand and obey all safety instructions supplied with accessories. The use of improper accessories may cause risk of injury to persons.

• Always use guards and eyeshields.The operation of any power tool can result in foreign object being thrown into the

eyes, which can result in severe eye damage. Always wear safety goggles complying with United States ANSI Z87.1. (shown on package) before commencing power tool operation.

Think safety! Safety is a combination of operator common sense and alertness at

all times when tool is being used.

SPECIFICATIONSModel 38UK50 16” Scroll Saw

Dimensions L x W x H (in) 24-3/4 x11-7/16 x 12- 13/16Table size (in) 10-1/16 x 16-5/16Saw blade length (in) 5”Motor Specifications 1/6 HP / 120V 60 Hz /

1.2 AmpsCutting height max (in) 2”Throat depth (in) 16”Stroke (in) 19/32”Stroke speed per minute (variable)

550-1650

Table tilting (left) 0 – 45Weight Net (lbs) 25.4 lbsDust port diameter (in) 1-3/8Sound level at max. speed during idle running

79 dB (A)

Model 38UK51 18” Scroll Saw

Dimensions L x W x H (in) 27-15/16 x 12-7/16 x 13- 9/16Table size (in) 9-13/16 x 18-9/16Saw blade length (in) 5”Motor Specifications 1/5 HP / 120V 60 Hz /

1.2 AmpsCutting height max (in) 2”Throat depth (in) 18”Stroke mm (in) 3/4”Stroke speed per minute (variable)

550 - 1600

Table tilting (left) -8 – 45Weight Net (lbs) 36.4 lbsDust port diameter (in) 1-3/8“Sound level at max. speed during idle running

79 dB (A)

5

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

SPECIFICATIONS (CONTINUED)Blade Specifications

Teeth/Inch

Width Thickness Speed spm

Material

10 .110” .020” 1200-1600 Hard and soft material 3/16” up to 2”

15 .110” .020” 800-1200 Extremely thin cuts on material 3/32” to 1/2” thick

18 .095” .010” 500-800 For tight radius work in thin materials 3/32” to 1/8” thick

INSTALLATIONAll electrical connections must be performed by a qualified electrician.

Power source

The motor is designed for operation on the voltage and frequency specified. Normal loads will be handled safely on voltages not more than 10% above or below specified voltage.

Running the unit on voltages which are not within the range may cause over heating and motor burn-out. Heavy loads require that the voltage at the motor terminals be no less than the voltage specified. Power supply to the motor is controlled by a double pole locking rocker switch. Remove the key to prevent unauthorized use.

Electrical connectionsMake sure unit is off and disconnected from power source while motor is being

mounted, connected, reconnected or any time wiring is inspected.

Electrical Safety

1. Double insulated tools are equipped with a polarizing plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.

Do not permit fingers to touch the terminals of plug when installing or

removing from outlet.

2. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate.

3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

4. Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock

5. Do not abuse the cord. Never use the cord to carry the tool or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

Extension cords

• The use of an extension cord will cause some drop in voltage and loss of power.

• Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.

• Use the table to determine the minimum wire size (A.W.G) extension cord.

• Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.

• If the extension cord is worn, cut or damaged in any way, replace it immediately.

Extension length

Wire Size A.W.G.Up to 25 ft 1625 to 100 ft 14

NOTE: Using extension cords over 100 ft long is not recommended.

This machine must be grounded. To avoid electrocution or fire, any repairs to

electrical system should be done only by a qualified electrician, using genuine replacement parts.

MA

INTE

NA

NC

E / R

EPA

IRTR

OU

BLE

SHO

OTI

NG

OPE

RAT

ION

ASS

EMB

LY /

INST

ALL

ATIO

NSA

FETY

/ SP

ECIF

ICAT

ION

SG

ETTI

NG

STA

RTE

D

6

INSTALLATION (CONTINUED)

Mounting the saw on a work bench

A workbench made from solid wood is better than one made from plywood, as interfering vibrations and noise are more noticeable with plywood. The necessary tools and small parts for assembling the saw on a workbench are not supplied with the saw. However, use equipment of at least the following size:

1. Saw body

2. Foam rubber base

3. Work bench

4. Flat seal

5. Washer

6. Hexagonal nut

7. Locking nut

8. Hexagonal bolt

Quantity description

4 Hexagonal bolts ¼-20 x length depends on bench thickness

4 Flat seal 9/32 1.0

4 Washers 9/32 1.0

8 Hexagonal nuts 1/4-20

First of all, drill holes into the seating surface and then insert the screws. A foam rubber base for reduction of noise is not supplied with the saw either. However, we expressly recommend that you use such a base to keep vibration and noise to a minimum. Ideal size 15-3/4” x 9-1/2”.

OPERATION

Always wear safety glasses complying with United States ANSI Z87.1 (shown on

package) before commencing power tool operation. Safety glasses are available through your Grainger catalog.

Scroll saw design features

1. Clamping screw: for removing the saw blade.

2. Shavings blower: keeps the work piece area free from dust.

3. Work piece holder

4. Angle scale: scale shows the tilting angle of the table.

5. On/Off power switch

6. Variable speed switch

7. Blade tension knob

8. Adjustable light

2

1

3

4

56

8

7

7

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

Setting the saw bench and angle scale

Release the angle adjustment knob (1) and bring the saw bench (2) to a right angle in relation to the saw blade. Use a 90˚ angle to measure the right angle between the blade and the bench. The saw blade should be 90˚ to the angle. Tighten the angle adjustment knob again when the distance between the blade and the 90˚ angle is at a minimum. The bench should then be at 90˚ to the saw blade. Release the lock screw and bring the angle indicator to the zero position. Tighten the screw. Please note: the angle scale is a useful piece of supplementary equipment, but should not be used for precise work. Use scrap wood for saw tests, adjust the bench if necessary.

Note: The table should not be on the motor block, this can cause undesirable noise.

Horizontal saw bench and diagonal cuts

The saw bench can be positions into a 45˚ diagonal position or be left in the horizontal position. You can read off the approximate degree of angle by using the angle scale located under the saw bench. For more exact adjustment, use scrap wood for some saw tests: adjust the bench if necessary.

Changing the saw blade - Flat saw blade (pinless)Switch off the saw and remove the power cord from the power supply before

installing saw blades in order to avoid injuries caused by unintentional activation of the saw.

Use adapters with the flat saw blades. The saw blade is fixed with Allen screws.

Saw blade removal

Extract the saw blade by sliding the table’s inlay up. Then unscrew the tightening screw. Slightly press the upper arm down (1). Remove the saw blade by pulling it forward out of the supports and through the access perforation in the table.

Inserting the saw blade

Put the saw blade with the two adapters into the lower support, the other end into the upper support. Slightly press the upper arm down (1) before hooking it in. Tighten the blade with the blade tension knob (2) by rotating it clockwise. Check the tightness of the blade. Keep on rotating clockwise to tighten the blade even more.

1

2

1

2

3

MA

INTE

NA

NC

E / R

EPA

IRTR

OU

BLE

SHO

OTI

NG

OPE

RAT

ION

ASS

EMB

LY /

INST

ALL

ATIO

NSA

FETY

/ SP

ECIF

ICAT

ION

SG

ETTI

NG

STA

RTE

D

8

OPERATION (CONTINUED)

Changing the saw blade – Saw blade with pinsSwitch off the saw and remove the power cord from the power supply before

installing saw blades in order to avoid injuries caused by unintentional activation of the saw.

Saw blade removal

Extract the saw blade by first unscrewing the tightening screw. Remove the saw blade from the upper and lower support by slightly pressing the saw’s upper arm down.

Inserting the saw blade

Lead one end of the saw blade through the perforation into the table and insert the saw blade pins into the notch. Repeat this procedure at the upper blade support

Before hooking it in, slightly press the saw’s upper arm down (1). Check the position of the blade pins at the supports. Tighten the blade by means of the blade tension knob (2). Check the blade’s tightness. Keep on rotating clockwise in order to tighten the blade even more.

Scroll saw usage

A scroll saw is fundamentally a “curve cutting tool” but which can also carry out straight and angled edge cuts. Familiarize yourself with the following important points prior to commissioning the saw

• The saw does not automatically cut wood. You must feed the wood against the saw blade manually.

• The cutting process occurs while the blade is moving.

• Feed the wood slowly against the saw blade as the blade teeth are small.

• Persons carrying out work with the saw require training. The saw blade may break easily during this training time while the operator is still unfamiliar with the saw.

• The saw is best suited for sheets of wood less than 25 mm (1”) thick.

• Feed the wood especially slowly against the blade and avoid abrupt curves to prevent the saw blade from breaking, if you wish to cut wood sheets thicker than 25 mm (1”).

• Saw blade teeth will dull over time, saw blades must be replaced. Blade wear depends on type of wood and operator.

• Try and make sure that the saw blade follows the grain of the wood in order to obtain a clean cut.

• The saw speed must be reduced to minimum when cutting precious and non-ferrous metals.

Scroll saw usage – inside cutsSwitch off the saw and remove the power cord from the power supply before

installing saw blades in order to avoid injuries caused by unintentional activation of the saw.

This saw is suited also to inside cuts or cuts not starting at the edge of the work piece. Proceed as follows:

• Drill a 6mm (1/4”) hole in the work piece.

• Turn the blade tension knob to release the tension on the blade.

• Place the bore hole over the saw blade slot in the work table.

• Install the saw blade through the hole in the work piece and through the work blade slot, and fasten the blade to the holders.

• When you have completed the inside cut, remove the saw blade and then remove the work piece from the table.

1

2

9

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

Symptom Possible Cause(s) Corrective Action

Saw blades break 1. Tension incorrectly set 1. Set the correct tension

2. Load to great 2. Feed the work piece more slowly

3. Incorrect saw blade variety 3. Use the correct saw blade

4. Work piece not fed straight 4. Avoid exerting side pressure

Motor does not function 1. Power extension cable faulty 1. Change faulty cable

2. Motor faulty 2. Call customer service. Do not attempt to repair the motor yourself as this should be carried out by trained personnel.

Vibration 1. Saw incorrectly installed 1. Refer to instructions in this manualNOTE: the saw vibrates slightly when the motor is running in normal operation.

2. Unsuitable underlay 2. The heavier the work bench is the less vibration. A bench made from plywood always vibrates more than one made from solid wood. Select the work bench best suited to your working conditions.

3. The work bench is not screwed down or is on the motor

3. Tighten the locking lever

4. The motor is not secured 4. Securely screw the motor in place

Saw blade swings out holders not aligned straight

1. Holders not aligned 1. Loosen the screws with which the holders are fastened to the arm. Align the holders so that they are perpendicular to each other and retighten the screws.

TROUBLESHOOTING GUIDE

MAINTENANCEIn the interests of operational safety, always switch off the saw and remove the cord from the

power supply before carrying out maintenance work.

GeneralRe-application of the wax coating on the work table makes feeding the work piece to the blade easier.

Motor

The power cord should be replaced immediately if pulled out, cut or damaged in any other way. Do not lubricate the motor bearings or internal parts.

Swing arm bearings

Lubricate the saw arm bearings every 10 hours. Proceed as follows.

• Turn the saw to the side.

• Apply a generous amount of SAE 20 oil to the shaft and end of the bronze bearings.

• Let the lubricant oil work overnight.

• Repeat the procedure the next day on the other side of the saw.

MA

INTE

NA

NC

E / R

EPA

IRTR

OU

BLE

SHO

OTI

NG

OPE

RAT

ION

ASS

EMB

LY /

INST

ALL

ATIO

NSA

FETY

/ SP

ECIF

ICAT

ION

SG

ETTI

NG

STA

RTE

D

10

Fo

r R

epai

r P

arts

, cal

l 1-8

00-G

rain

ger

24 h

ou

rs a

day

– 3

65 d

ays

a ye

arP

leas

e pr

ovid

e fo

llow

ing

info

rmat

ion:

-Mod

el n

umbe

r-S

eria

l num

ber (

if an

y)-P

art d

escr

iptio

n an

d nu

mbe

r as

show

n in

par

ts li

st

RE

PAIR

PA

RT

S I

LLU

ST

RA

TIO

N F

OR

38U

K50

- 16

” S

CR

OLL

SA

W

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

11

1 PHLP HD SCR M5X8 62 Flat Washer M5 63 Side Cover 9639060.01 14 Hex Nut M6 55 Lock Washer M6 96 Base <> 17 Dust Cap 9639061.01 48 Left Arm Housing 9639062.01 19 Tension Bolt Assy 9639063.01 110 Arm Spring 9639064.01 111 Pressure Plate 9639665.01 212 Lock Washer M4 313 Cap Screw M4X10 214 Lower Arm 9639066.01 115 Upper Arm 9639067.01 116 Oil Sleeve Bearing 9639068.01 417 Air Nozzle 9639069.01 118 Hex Bolt M5X6 119 Right Arm Housing 9639070.01 120 Lock Washer D5 1121 Hex Bolt M5X35 523 Bellows Cap 9639071.01 124 Hex Bolt M5X28 225 Star Knob 9639072.01 126 Switch Cover 9639073.01 127 Power Switch 9630974.01 128 Bellows 9639075.01 129 Mounting Plate 9639076.01 230 Carriage Bolt M6X20 431 Upper Blade Support 9639077.01 132 EXT Tooth Washer M4 233 Cap Screw M4X20 234 Support Spacer 9639078.01 235 Blade 9639079.01 136 Cap Screw M5X25 137 Big Spacer 9639080.01 138 Eccentric Connector 9639081.01 139 Ball Bearing 9639082.01 240 Hex Nut M5 241 Eccentric Connector Plate 9639083.01 142 Tap Screw ST4.2X9.5 543 Small Spacer 9639084.01 144 Cap Screw M5X16 145 Lower Blade Support 9639085.01 146 Star Knob 9639086.01 147 Drop Foot Guide Post 9639087.01 148 PHLP HD SCR M5X30 249 Blade Guard 9639088.01 150 Drop Foot 9639089.01 151 Flat Washer M6 152 PHLP HD SCR M6X10 253 Air Hose 9639090.01 154 Flat Washer M8 2

55 Cap Screw M8X25 256 Hex Bolt M6X20 457 Big Flat Washer M6 458 Compression Spring 9639091.01 159 Cap Screw M6X35 260 Table Mounting Bracket 9639092.01 161 Pointer 9639093.01 162 Scale 9639094.01 163 Table 9639095.01 164 Table Insert 9639096.01 165 Variable Speed Knob 9639097.01 166 Cap Screw M5x6 167 Power Cord 9639098.01 168 PHLP HD SCR M4X8 269 Set Screw M8X12 170 Eccentric Counterweight 9639099.01 171 Motor DC 9639100.01 172 Front Housing 9639101.01 173 Strain Relief 9639102.01 174 PHLP HD SCR M4X10 475 Potentiometer 9639103.01 176 Circuit Board 9639104.01 1

REPAIR PARTS LIST FOR 38UK50 – 16” SCROLL SAW Ref. No. Description Part Number: Qty.

Ref. No. Description Part Number: Qty.

(∆) Not Shown (*) Standard hardware item available locally (N/A) Not available as replacement part

MA

INTE

NA

NC

E / R

EPA

IRTR

OU

BLE

SHO

OTI

NG

OPE

RAT

ION

ASS

EMB

LY /

INST

ALL

ATIO

NSA

FETY

/ SP

ECIF

ICAT

ION

SG

ETTI

NG

STA

RTE

D

12

Fo

r R

epai

r P

arts

, ca

ll 1-

800-

Gra

ing

er24

ho

urs

a d

ay –

365

day

s a

year

Ple

ase

prov

ide

follo

win

g in

form

atio

n:-M

odel

num

ber

-Ser

ial n

umbe

r (if

any)

-Par

t des

crip

tion

and

num

ber a

s sh

own

in p

arts

list

RE

PAIR

PA

RT

S I

LLU

ST

RA

TIO

N F

OR

38U

K51

- 18

” S

CR

OLL

SA

W

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

13

1 Hex bolt M6x20 62 Standard spring washer M6 103 Hex bolt M6x12 44 Pressure plate 9639010.01 105 Philips screw M4x6 107 Base * 18 Soft pipe 9639011.01 19 Oil cushion 9639012.01 410 Hex nut,type’I” M5 311 Left housing set 9639013.01 112 Bearing with oil 9639014.01 413 Hex socket screw M4x20 214 Standard spring washer M4 115 Pressure plate 9639015.01 216 Philips screw M5x8 917 Spring 9639016.01 118 Bolt tension assy 9639017.01 119 Lower rocker assy 9639018.01 120 Uper rocker assy 9639019.01 121 Right housing set 9639020.01 122 Philips screw M5x48 823 Light assy 9639021.01 124 Hex socket screw M5x8 225 Blade adaptor 9639022.01 226 Hex socket screw M4x10 227 Toothed lock washer M4 228 Blade housing set 9639023.01 229 Blade * 130 Hex socket screw M5x30 231 Standard spring washer M5 532 Big spacer 9639024.01 133 Bearing with dustproof cover 9639025.01 234 Small spacer 9639026.01 135 Eccentric connector 9639027.01 136 Hex socket screw M5x16 137 Connector plate 9639028.01 138 Philips screw ST4.2x9.5 539 Philips screw M3x10 240 Bellows base 9639029.01 141 Syphon 2 9639030.01 142 Syphon 1 9639031.01 143 Bellows 9639032.01 144 Tension bolt lock handle 9639033.01 145 Tension bolt 9639034.01 146 Hex socket screw M5x10 247 Air Nozzle 9639035.01 148 Blade protector 9639036.01 149 Flat washer M5 550 Work table pin shaft 9639037.01 151 Saddle spring washer M8 152 Philips screw M4x8 253 Side cover 9639038.01 154 Table stand 9639039.01 1

55 Scale 9639040.01 156 Big flat washer M6 157 Pointer 9639041.01 158 Flat washer M4 159 Philips screw M4x12 560 Table lock handle 9639042.01 161 Table screw 9639043.01 162 Work table 9639044.01 163 Table insert 9639045.01 169 Stand cover 9639046.01 170 Blade guard connect plate 9639047.01 171 Hex nut, type I M4 272 Philips screw M4 273 Hex socket screw M8x12 174 Eccentricity pulley 9639048.01 175 Hex socket screw M5x6 176 Variable speed handle 9639049.01 177 Power switch 9639050.01 178 Junction box cover 9639051.01 179 Circuit board 9639052.01 180 Junction box 9639053.01 181 Philips screw M4X20 482 clip 9639054.01 183 Cord & plug 9639055.01 184 Big flat washer M5 185 Motor assy 9639056.01 1

REPAIR PARTS LIST FOR 38UK51 – 18” SCROLL SAW Ref. No. Description Part Number: Qty.

Ref. No. Description Part Number: Qty.

(∆) Not Shown (*) Standard hardware item available locally (N/A) Not available as replacement part

NOTES

MA

INTE

NA

NC

E / R

EPA

IRO

PER

ATIO

NA

SSEM

BLY

/ IN

STA

LLAT

ION

SAFE

TY /

SPEC

IFIC

ATIO

NS

GET

TIN

G S

TAR

TED

14

TRO

UB

LESH

OO

TIN

G

NOTES

GETTIN

G STA

RTED

SAFETY / SPEC

IFICATIO

NS

ASSEM

BLY / IN

STALLATIO

NO

PERATIO

NTR

OU

BLESH

OO

TING

MA

INTEN

AN

CE / R

EPAIR

15

DAYTON ONE-YEAR LIMITED WARRANTY

DAYTON ONE-YEAR LIMITED WARRANTY. All Dayton® product models covered in this manual are warranted by Dayton Electric Mfg. Co. (“Dayton”) to the original user against defects in workmanship or materials under normal use for one year after date of purchase. If the Dayton product is part of a set, only the portion that is defective is subject to this warranty. Any product or part which is determined to be defective in material or workmanship and returned to an authorized service location, as Dayton or Dayton’s designee designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced with a new or reconditioned product or part of equal utility or a full refund given, at Dayton’s or Dayton’s designee’s option, at no charge. For limited warranty claim procedures, see “Warranty Service” below. This warranty is void if there is evidence of misuse, mis-repair, mis-installation, abuse or alteration. This warranty does not cover normal wear and tear of Dayton products or portions of them, or products or portions of them which are consumable in normal use. This limited warranty gives purchasers specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction.

WARRANTY DISCLAIMERS AND LIMITATIONS OF LIABILITY RELATING TO ALL CUSTOMERS FOR ALL PRODUCTS

LIMITATION OF LIABILITY. TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW, DAYTON’S LIABILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES IS EXPRESSLY DISCLAIMED. DAYTON’S LIABILITY IN ALL EVENTS IS LIMITED TO AND SHALL NOT EXCEED THE PURCHASE PRICE PAID.

WARRANTY DISCLAIMER. A DILIGENT EFFORT HAS BEEN MADE TO PROVIDE PRODUCT INFORMATION AND ILLUSTRATE THE PRODUCTS IN THIS LITERATURE ACCURATELY; HOWEVER, SUCH INFORMATION AND ILLUSTRATIONS ARE FOR THE SOLE PURPOSE OF IDENTIFICATION, AND DO NOT EXPRESS OR IMPLY A WARRANTY THAT THE PRODUCTS ARE MERCHANTABLE, OR FIT FOR A PARTICULAR PURPOSE, OR THAT THE PRODUCTS WILL NECESSARILY CONFORM TO THE ILLUSTRATIONS OR DESCRIPTIONS. EXCEPT AS PROVIDED BELOW, NO WARRANTY OR AFFIRMATION OF FACT, EXPRESSED OR IMPLIED, OTHER THAN AS STATED IN THE “LIMITED WARRANTY” ABOVE IS MADE OR AUTHORIZED BY DAYTON.

PRODUCT SUITABILITY. MANY JURISDICTIONS HAVE CODES AND REGULATIONS GOVERNING SALES, CONSTRUCTION, INSTALLATION, AND/OR USE OF PRODUCTS FOR CERTAIN PURPOSES, WHICH MAY VARY FROM THOSE IN NEIGHBORING AREAS. WHILE ATTEMPTS ARE MADE TO ASSURE THAT DAYTON PRODUCTS COMPLY WITH SUCH CODES, DAYTON CANNOT GUARANTEE COMPLIANCE, AND CANNOT BE RESPONSIBLE FOR HOW THE PRODUCT IS INSTALLED OR USED. BEFORE PURCHASE AND USE OF A PRODUCT, REVIEW THE SAFETY/SPECIFICATIONS, AND ALL APPLICABLE NATIONAL AND LOCAL CODES AND REGULATIONS, AND BE SURE THAT THE PRODUCT, INSTALLATION, AND USE WILL COMPLY WITH THEM.

CONSUMERS ONLY. CERTAIN ASPECTS OF DISCLAIMERS ARE NOT APPLICABLE TO CONSUMER PRODUCTS SOLD TO CONSUMERS; (A) SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU; (B) ALSO, SOME JURISDICTIONS DO NOT ALLOW A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU; AND (C) BY LAW, DURING THE PERIOD OF THIS LIMITED WARRANTY, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO CONSUMER PRODUCTS PURCHASED BY CONSUMERS, MAY NOT BE EXCLUDED OR OTHERWISE DISCLAIMED.

THIS LIMITED WARRANTY ONLY APPLIES TO UNITED STATES PURCHASERS FOR DELIVERY IN THE UNITED STATES.

WARRANTY SERVICE

To obtain warranty service if you purchased the covered product directly from W.W. Grainger, Inc. (“Grainger”), (i) write or call or visit the local Grainger branch from which the product was purchased or another Grainger branch near you (see www.grainger.com for a listing of Grainger branches); or (ii) contact Grainger by going to www.grainger.com and clicking on the “Contact Us” link at the top of the page, then clicking on the “Email us” link; or (iii) call Customer Care (toll free) at 1-888-361-8649. To obtain warranty service if you purchased the covered product from another distributor or retailer, (i) go to www.grainger.com for Warranty Service; (ii) write or call or visit a Grainger branch near you; or (iii) call Customer Care (toll free) at 1-888-361-8649. In any case, you will need to provide, to the extent available, the purchase date, the original invoice number, the stock number, a description of the defect, and anything else specified in this Dayton One-Year Limited Warranty. You may be required to send the product in for inspection at your cost. You can follow up on the progress of inspections and corrections in the same ways. Title and risk of loss pass to buyer on delivery to common carrier, so if product was damaged in transit to you, file claim with carrier, not retailer, Grainger or Dayton. For warranty information for purchasers and/or delivery outside the United States, please use the following applicable contact information:

Dayton Electric Mfg. Co., 100 Grainger Parkway, Lake Forest, IL 60045 U.S.A. or call +1-888-361-8649