03-hlr9820 sau hardware & local office data issue2.2

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved

www.huawei.com

Internal

OWF001202 HLR9820 SAU Hardware & Local

office Data

ISSUE 2.2

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

Introduction

Hardware data configuration is the first step of SAU data

configuration.

After this course, trainees will understand HLR9820 hardware

in-depth.


Upon completion of this course, you

will be able to:

Master the hardware& local office

data configuration.

Master all the logical NO. principle.


Chapter 1 Basic conceptsChapter 1 Basic concepts

Chapter 2 Data configurationChapter 2 Data configuration

Chapter 3 Relative maintenance commandChapter 3 Relative maintenance command

Chapter 4 Configuration exampleChapter 4 Configuration example


HLR9820 data works for: SAU (Signaling Processing)

HDU (MAP Services Processing)

The data is configured in: LMT (For SAU)

Hardware Data

Local Office Information

Signaling Data

SMU Client (For HDU)

Global Data

Where is the data configured?



1.1 Elements and position1.1 Elements and position

1.2 Module1.2 Module

1.3 Preparations1.3 Preparations

1.4 Data config. sequence1.4 Data config. sequence


Elements and position

Module structure

HLR9820

Cabinet Cabinet

Frame Frame

Board Board

…

…

…



Cabinet

HLR9820 has 1 or 2 cabinets.



Frame and board

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

W B S G

W C C U

W C C U

W B S G

W I F M

P S M

W C S U

W C S U

W S M U

W H S C

W E P I

W E P I

W S I U

W C K I

W C K I

W B F I

W B F I

W S I U

W S I U

Front

Back

W I F M

W S M U

P S M

P S M

P S M

SAU has two kinds of frames:

basic frame and expansion frame.

There are 1 basic and two

expansion frames in full

configuration.

Only IBM solution has expansion

frame. It depends on numbers of

subscriber.

Front board and back board



Type and function of the boards

Front board Back boardWSMU System Management Board WSIU System Interface Board

WCCU Call Control Board - -

WEAM E1 ATM forward WEPI ATM Interface Board

WCSU Call Control and Signaling Processing Board

WEPI E1 Interface Board

WBSG Broadband Signaling Processing Board

- -

WIFM IP Transferring Module Board WBFI Back Far End Interface Board

WALU Alarm Board

PSM Power Supply Board PSM Power Supply Board

- - WHSC Hot-swap Control Board

- - WCKI Clock Interface Board



Number of devices

To help in recognizing all categories of module components, it is necessary to number those of the same category uniformly.

Shelf number To recognize individual shelves easily, each shelf is given a number, called shelf number. The shelf with the basic frame is numbered as Shelf 0.



Number of devices

Frame number

The system can support ten frames at most, numbering from 0 to 9. The basic frame in the integrated configuration shelf is numbered as Frame 0.


The 8-bit Dual Inline Package (DIP) S3 of SIU is provided for setting frame numbers. The corresponding setting table is shown in follow


DIP

Frame No.

8 7 6 5 4 3 2 1

0 on on on on on on on on

1 on on on on on on on off

2 on on on on on on off on

3 on on on on on on off off

4 on on on on on off on on

5 on on on on on off on off

6 on on on on on off off on

7 on on on on on off off off

8 on on on on off on on on

9 on on on on off on on off


Slot number

Slot number is used to identify the slot of a specific

board that is inserted into a frame.

Each frame contains 21 slots at most (No. from 0 to

20)



Module

Module number

Module number is set according to the type of the board

and is numbered from 2.

Modules of the same board are numbered uniquely. Here

are the numbering rules:

WSMU Module number: 2~21

WCCU/WCSU Module number: 22~101

WEAM/WIFM/WBSG Module number: 132~211


Preparations

Before the data configuration, you should know

The networking and configuration conditions

The requirements put forward during engineering design

stage

The local office information (SPC/HLR No./CC etc.)


Common MML commands

Command Function

ADD Add database data

MOD Modify database data

RMV Delete database data

LST Query database data

DSPQuery status of related equipment and resource

SET Set data or status

LOF Start offline mode

LON Start online mode


Offline

Command or step Function

LOF Start the offline mode

SET CWSON: SWT=OFFSet the alarm output switch of the current workstation to OFF

SET FMT: STS=OFF Set format status to OFF

If it is the initial data configuration for the deployment:


Online

Command or step Function

LON Start the online mode

SET CWSON: SWT=ON Set the alarm output switch of the current workstation to ON

SET FMT: STS=ON Set format status to ON

FMT Format all data of all modules

Loading data in power-down statusRemove two Wireless System Management Units (WSMUs) to simulate equipment power-down and then load data.

After that, how to load the data to switch?


HLR9820 Data Configuration Sequence

Start

End

Configure local office information

Configure signaling data

Configure hardware data

Start

End

Configure local office information

Configure signaling data

Configure hardware data


Questions

What’s the numbering principle of shelf, fr

ame, board?

Which board has module number?

Can boards in same module exist in differ

ent frames?

What’s the difference of online and offline

mode?



2.1 Configuration Flow2.1 Configuration Flow

2.2 Data configuration2.2 Data configuration


Configuration Flow

Add ShelfAdd Shelf

Add FramesAdd Frames

Add BoardsAdd Boards

Add WCSUAdd WCSU Add WCKIAdd WCKI

Add WIFMAdd WIFM

Add WEPIAdd WEPI

Conf. E1Conf. E1

Conf. clock ModeConf. clock Mode

Conf. FEConf. FEConf. CPCConf. CPC

Conf. MEMConf. MEM

Clock Refer.Clock Refer.

Add WCCUAdd WCCU

Set Local OfficeInformation



Configuration Flow for ATM

Add ShelfAdd Shelf

Add FramesAdd Frames

Add BoardsAdd Boards

Add WEAMAdd WEAM Add WCKIAdd WCKI

Add WEPIAdd WEPI

Conf. IMA/UNIConf. IMA/UNI

Conf. clock ModeConf. clock Mode

Conf. MEMConf. MEM

Clock Refer.Clock Refer. Conf. PVCConf. PVC

Add WCCUAdd WCCU

Conf. E1Conf. E1





2.1 Configuration Flow2.1 Configuration Flow

2.2 Data configuration2.2 Data configuration


Commands

Adding Shelf

Adding Frame

Adding Board

Adding E1

Setting Clock Mode

Adding Board Clock Reference Source

Adding FE Configuration

Adding MEM Configuration

Adding IMA group

Adding IMA link

Adding UNI link

Adding PVC link

Set Local Office Information


Shelf/Frames/Boards

Relationship

[Shelf Number][Location Title][Position Number][RoW Number][Column Number]

ADD SHF

[Frame Number][Shelf Number][Position Number]

ADD FRM

[Frame Number][Slot Number][Location]

ADD BRD


Shelf/Frames/Boards

Add Shelf

For HLR9820 SAU, there is only one shelf. The number always is 0.


Shelf/Frames/Boards

Add Frames

• For SUN solution, there is only one frame. The frame number is always 0.• For IBM Solution, there are three frames at maximum configuration. The frame number are from 0 to 2.


Shelf/Frames/Boards

Add Boards

Before adding the boards, the frame and shelf to which the

boards belong must have already been added.

WSMU/WALU/PSM will be added automatically after the

frame has been added.

If parameters need to be modified, please delete the board

at first then add it again.

Two pieces of CPC will be added automatically after the

WCSU has been added.


Add E1

Configure the WEPI if the module needs to process the SS7.


Set Clock Mode

Only for TDM/ATM networking

SET CKICFG: CL=LEVEL2, WM=MANUAL, MCS=LCK1;


Board Clock Reference Source

Only for TDM/ATM networking

After configuring clock mode

Parameter indicate the physical position:• Frame No.• Slot No.• E1 No.


Add FE configuration

Function:

WIFM/WBFI is the interface between SAU and IP network.

They process MAC and IP protocol.

WIFM deliver IP package to WBSG.

We need setup FE (Fast Ethernet) interface for signaling

traffic.


Add MEM configuration

Function:

Setup the connection between SAU and HDU


WCSU/WCCU

WHSC0

WHSC1

HDU1#

HDU2#

LAN

SWITCH

LAN

SWITCH

WCSU/WCCU

MODULE

Hardware Connection


Command

ADD MEMCFG

Module: Module No. of WCCU/WCSU.

Local IP address: IP of WCSU. it is defined by this command.

Remote IP address: IP of HDU. Come from HDU.

Remote Port: IP port of HDU, always be 16500.

MEM Configuration


Command

ADD IMAGRP

WEAM Module: Module No. of .WEAM

IMA Group No.: Number of IMA group, ranging from 0 to 7.

Add IMA group


Command

ADD IMALNK

WEAM Module: Module No. of WEAM

IMA Group No.: Number of IMA group, ranging from 0 to 7.

IMA link port no: Number of the E1 port added to the IMA group

Add IMA link


Command

ADD UNILNK

WEAM Module: Module No. of WEAM

UNI link port no: Number of the E1 port added to the IMA group

Add UNI link


Command

ADD PVCLNK

PVC link number: Number of the global PVC links

VPI: Virtual path identifier (VPI)

VCI: virtual channel identifier (VCI)

Signal distribution module number:

Signal handle module number:

IMA group number:

UNI port number:

Add PVC link


Command

Set OFI

Signaling point code (SPC)

Signaling network where the local office resides (NI)

Network Structure

Whether the local office is a signaling transfer point (STP)

Add OFI

Signaling point code (SPC)

Set Local Office Information


Questions

What’s the sequence for hardware data conf.?

Which board will be added automatically after a

frame has been added?

How to make the data active in switch after we

configure the data offline?

What conditions are needed for E1 configuration?


Answer

1 Add shelf-> Add frame-> Add board->others

2 WSMU ， WALU 和 PSM 。 Use FMT to format data. Use LON to set online. Then lo

ad it.

We need add WCSU and WEPI at first.


3.1 Query Hardware3.1 Query Hardware

3.2 Query clock reference3.2 Query clock reference

3.3 Query E1/CPC configuration3.3 Query E1/CPC configuration

3.4 Query IP link3.4 Query IP link

3.5 Query IMA/UNI link3.5 Query IMA/UNI link

3.6 Query Port Status3.6 Query Port Status

3.7 Query Local Office3.7 Query Local Office

Chapter 3 Chapter 3 Relative maintenance commandRelative maintenance command


Query The Hardware

LST SHF

Example: LST SHF: SN=0;

LST FRM

Example: LST FRM: FN=0, SN=0;

DSP FRM

Example: DSP FRM: FN=0;


Query The Hardware

LST BRD

Example: LST BRD: FN=0, SN=0, LOC=FRONT;

DSP BRD

Example: DSP BRD: FN=0, SN=0, PSN=FB;


Query clock reference

LST CKICFG

Example: LST CKICFG:;

DSP CLKPH

Example: DSP CLKPH: FN=0;

DSP BRD (Query status of clock reference)

Example: DSP BRD: FN=0, SN=13, PSN=BB;


Query E1/CPC configuration

LST EPICFG

Example: LST EPICFG: FN=0, SN=0;

DSP BRD

Example: DSP BRD: FN=0, SN=0, PSN=BB;

Display E1 status

Example: DSP PORT: FN=0, SN=0, PT=E1, E1PN=2;

LST CPCCFG

Example: LST CPCCFG: FM=22, LOC=UPMC;


Query IP link

List FE configuration

Example: LST FECFG: MN=134;

Display FE status

Example: DSP PORT: FN=0, SN=10, PT=FE, FEPN=2;


Query IMA/UNI link

List IMA link configuration

Example: LST IMALNK: MN=132, IGN=1, IPN=0;

Display IMA link status

Example: DSP IMALNK: MN=132, IGN=1, IPN=0;

List UNI link configuration

Example: LST UNILNK: MN=133;

Display UNI link status

Example: LST UNILNK: MN=133;


Query Port Status (MEM FE)

To check connection between SAU and HDU

List MEMFE link configuration

Example: LST MEMCFG: MN=22;

Display MEMFE link status

Example: DSP MEMFE: MN=22;


Query Local Office Information

List local office information

Example: LST OFI;


Questions

What’s the difference between LST and DSP?

Which command is to check current clock reference?


Answer

LST is for query static data; DSP is for query the status of

frame/board etc.

DSP BRD is used to check current clock reference. (Board is

active WCKI)


Summary After hardware data

configuration, please load it to

switch. Then query whether the

status of hardware is normal.


Example for hardware

IP address of WIFM: 191.169.100.10;

Mask: 255.255.0.0;

Gateway: 191.169.1.2 。

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

W

C

S

U

W

C

S

U

W

C

C

U

W

C

C

U

W

E

A

M

W

E

A

M

W

S

M

U

W

S

M

U

W

I

F

M

W

I

F

M

W

B

S

G

W

B

S

G

W

A

L

U

P

S

M

P

S

M


Item Configuration data

Signaling pointNetwork Identify Network structure SPC

National 24bits EE0

Mobile network

information

Local GT Country code Area code

8613807550000 86 755

MAP information

Support of USSD function value

MAP version 0902620Not support CAMEL phrase 1

Maximum times of Call Forward

True False False 3

Support of Message waiting information

Cancel SCRepetition times of ALERT_SC fail

Forwarded area limitation

True False 3 NORESTRICTION

Number structure limitation

MAP versionAnytime interrogation support

Support of PSI value

NORESTRICTION GSM PHASE2 True True

Support of GPRS short message

True

Example



1 set offline mode

Offline------------------------LOF:;

Turn off alarm switch------------------------SET CWSON: SWT=OFF;

Turn off format switch------------------------

SET FMT: STS=OFF;



2 Add Hardware

Add shelf------------------------ADD SHF: SN=0, LT="HW_TC", PN=0, RN=0, CN=0;

Add frame------------------------ADD FRM: FN=0, SN=0, PN=2, CF=YES;


Add WCSU board------------------------ADD BRD: FN=0, SN=0, LOC=FRONT, BT=WCSU, MN=22, ASS=1;

Add WEAM board------------------------ADD BRD: FN=0, SN=4, LOC=FRONT, BT=WEAM, MN=140, LNKT=LINK_2M;ADD BRD: FN=0, SN=5, LOC=FRONT, BT=WEAM, MN=141, LNKT=LINK_2M;



Add WEPI board

------------------------

ADD BRD: FN=0, SN=0, LOC=BACK, BT=WEPI;




Add WIFM board

------------------------

ADD BRD: FN=0, SN=10, LOC=FRONT, BT=WIFM, MN=132, ASS=11;



Add WCCU board

------------------------

ADD BRD: FN=0, SN=2, LOC=FRONT, BT=WCCU, MN=23, ASS=3;

Add WBSG board

------------------------

ADD BRD: FN=0, SN=12, LOC=FRONT, BT=WBSG, MN=133;

ADD BRD: FN=0, SN=13, LOC=FRONT, BT=WBSG, MN=134;



Add WCKI board

------------------------

ADD BRD: FN=0, SN=13, LOC=BACK, BT=WCKI;

ADD BRD: FN=0, SN=15, LOC=BACK, BT=WCKI;




3 ： Configure E1/CPC/FE/ATM data

Configure E1 info

------------------------

ADD EPICFG: FN=0, SN=0, LC=CLK_8KA, E0=CRC4, E1=DF,

E2=DF, E3=DF, E4=DF, E5=DF, E6=DF, E7=DF, BM=BALANCE;

Configure CPC info

------------------------

MOD CPCCFG: FM=22, LOC=UPMC, LTYPE=LINK_64K;


Configure clock reference------------------------------SET CKICFG: CL=LEVEL2, WM=AUTO, B1P=L1, B2P=L2, L1P=L3, L2P=L4, B1CST=CLK_2M, B2CST=CLK_2M;

Configure clock from E1------------------------------ADD BOSRC: FN=0, SN=0, EN=2;


Configure FE------------------------ADD FECFG: MN=132, IP="191.169.100.10", MSK="255.255.0.0", DGW="191.169.1.2";


Configure IMA link

------------------------

ADD IMAGRP: MN=140, IGN=0, IID=0, IVR=VER1.1;

ADD IMALNK: MN=140, IGN=0, IPN=0;

Configure PVC link

------------------------

ADD PVCLNK: PLN=0, VPI=2, VCI=4, SDMN=140, SHMN=133,

BT=IMA;




4: Set Local Office Data

Online

------------------------

SET OFI: OFN="HLR-TEST", LOT=CMPX, NN=YES, SN1=NAT,

SN2=NAT, SN3=NAT, SN4=NAT, NPC=“EE00", NNS=SP14, STP=NO,

LAC=K‘755, LNC=K‘86, LOCGT=“861380755",

NETTYPE=GSM/PSTN;



5: Format the data, load it

Online------------------------LON:;Turn on alarm switch------------------------SET CWSON: SWT=ON;Turn on format switch------------------------SET FMT: STS=ON;Format the data------------------------FMT:;Load the module one by one


Summary

After finish hardware data, trainees need

master the basic concepts of hardware.

Trainees need understand the steps of

SAU hardware data configuration

www.huawei.com

Thank You

03-hlr9820 sau hardware & local office data issue2.2

Documents