planet.com.ru · user’s manual . 3 . table of contents . 1. introduction

User’s Manual

1

User’s Manual

2

Trademarks Copyright © PLANET Technology Corp. 2018. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred. Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to this User's Manual and/or to the products described in this User's Manual, at any time without notice. If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Energy Saving Note of the Device This power required device does not support Standby mode operation. For energy saving, please remove the power cable to disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power consumption, it is strongly suggested to remove the power connection for the device if this device is not intended to be active.

WEEE Warning

To avoid the potential effects on t he environment and human health as a r esult of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision PLANET WGS-5225 Series User's Manual

Model: WGS-5225-8P2S/WGS-5225-8P2SV/WGS-5225-8T2SV

Revision: 1.0 (March, 2018)

Part No: EM-WGS-5225 series _v1.0

User’s Manual

3

TABLE OF CONTENTS

1. INTRODUCTION .................................................................................................................. 10

1.1 Packet Contents ......................................................................................................................................... 10

1.2 Product Description ................................................................................................................................... 11

1.3 How to Use This Manual ............................................................................................................................ 18

1.4 Product Features ........................................................................................................................................ 19

1.5 Product Specifications .............................................................................................................................. 22

2. INSTALLATION ................................................................................................................... 26

2.1 Hardware Description ................................................................................................................................ 26 2.1.1 Physical Dimensions ........................................................................................................................................... 26

2.1.2 LED Indications ................................................................................................................................................... 29 2.1.3 Wiring Power Input .............................................................................................................................................. 31

2.2 Installing the Wall-mount Managed Switch ............................................................................................. 32 2.2.1 Wall-mount Installation ........................................................................................................................................ 32 2.2.2 Magnet Installation .............................................................................................................................................. 33 2.2.3 DIN-rail Installation .............................................................................................................................................. 33 2.2.4 Installing the SFP Transceiver ............................................................................................................................. 35

3. SWITCH MANAGEMENT .................................................................................................... 39

3.1 Requirements ............................................................................................................................................. 39

3.2 Management Access Overview ................................................................................................................. 40

3.3 Remote Telnet Management ...................................................................................................................... 41

3.4 Web Management and LCD Touch Screen .............................................................................................. 41

3.5 SNMP-based Network Management ......................................................................................................... 44

3.6 PLANET Smart Discovery Utility .............................................................................................................. 45

4. WEB CONFIGURATION ...................................................................................................... 47

4.1 Main Web Page ........................................................................................................................................... 50

4.2 System ......................................................................................................................................................... 52 4.2.1 System Information .............................................................................................................................................. 53

User’s Manual

4

4.2.2 IP Configuration ................................................................................................................................................... 54 4.2.3 IP Status .............................................................................................................................................................. 56 4.2.4 Users Configuration ............................................................................................................................................. 57 4.2.5 Privilege Levels ................................................................................................................................................... 60 4.2.6 NTP Configuration ............................................................................................................................................... 61 4.2.7 Time Configuration .............................................................................................................................................. 62 4.2.8 UPnP ................................................................................................................................................................... 64 4.2.9 DHCP Relay ........................................................................................................................................................ 66 4.2.10 DHCP Relay Statistics ....................................................................................................................................... 67 4.2.11 CPU Load .......................................................................................................................................................... 69 4.2.12 System Log ........................................................................................................................................................ 70 4.2.13 Detailed Log ...................................................................................................................................................... 71 4.2.14 Remote Syslog .................................................................................................................................................. 72 4.2.15 SMTP Configuration .......................................................................................................................................... 73 4.2.16 Fault Alarm ........................................................................................................................................................ 74 4.2.17 Web Firmware Upgrade ..................................................................................................................................... 75 4.2.18 TFTP Firmware Upgrade ................................................................................................................................... 76 4.2.19 Save Startup Config .......................................................................................................................................... 77 4.2.20 Configuration Download .................................................................................................................................... 77 4.2.21 Configuration Upload ......................................................................................................................................... 78 4.2.22 Configuration Activate ........................................................................................................................................ 78 4.2.23 Configuration Delete .......................................................................................................................................... 79 4.2.24 Image Select ...................................................................................................................................................... 79 4.2.25 Factory Default .................................................................................................................................................. 80 4.2.26 System Reboot .................................................................................................................................................. 81

4.3 Simple Network Management Protocol .................................................................................................... 82 4.3.1 SNMP Overview .................................................................................................................................................. 82 4.3.2 SNMP System Configuration ............................................................................................................................... 83 4.3.3 SNMP Trap Configuration .................................................................................................................................... 85 4.3.4 SNMP System Information .................................................................................................................................. 87 4.3.5 SNMPv3 Configuration ........................................................................................................................................ 88

4.3.5.1 SNMPv3 Communities .............................................................................................................................. 88 4.3.5.2 SNMPv3 Users .......................................................................................................................................... 89 4.3.5.3 SNMPv3 Groups ....................................................................................................................................... 90 4.3.5.4 SNMPv3 Views .......................................................................................................................................... 91 4.3.5.5 SNMPv3 Access ........................................................................................................................................ 92

4.4 Port Management ....................................................................................................................................... 94 4.4.1 Port Configuration ................................................................................................................................................ 94 4.4.2 Port Statistics Overview ....................................................................................................................................... 96 4.4.3 Port Statistics Detail ............................................................................................................................................ 96

User’s Manual

5

4.4.4 SFP Module Information ...................................................................................................................................... 98 4.4.5 Port Mirror.......................................................................................................................................................... 101

4.5 Link Aggregation ...................................................................................................................................... 103 4.5.1 Static Aggregation ............................................................................................................................................. 105 4.5.2 LACP Configuration ........................................................................................................................................... 106 4.5.3 LACP System Status ......................................................................................................................................... 109 4.5.4 LACP Port Status .............................................................................................................................................. 110 4.5.5 LACP Port Statistics .......................................................................................................................................... 111

4.6 VLAN .......................................................................................................................................................... 112 4.6.1 VLAN Overview ................................................................................................................................................. 112 4.6.2 IEEE 802.1Q VLAN ........................................................................................................................................... 113 4.6.3 VLAN Port Configuration ................................................................................................................................... 116 4.6.4 VLAN Membership Status ................................................................................................................................. 122 4.6.5 VLAN Port Status .............................................................................................................................................. 124 4.6.6 Private VLAN ..................................................................................................................................................... 125 4.6.7 Port Isolation ...................................................................................................................................................... 127 4.6.8 VLAN setting example: ...................................................................................................................................... 129

4.6.8.1 Two Separate 802.1Q VLANs.................................................................................................................. 129 4.6.8.2 VLAN Trunking between two 802.1Q aware switches ............................................................................. 131 4.6.8.3 Port Isolate .............................................................................................................................................. 134

4.6.9 MAC-based VLAN ............................................................................................................................................. 135 4.6.10 MAC-based VLAN Status ................................................................................................................................ 137 4.6.11 IP Subnet-based VLAN .................................................................................................................................... 137 4.6.12 Protocol-based VLAN ...................................................................................................................................... 139 4.6.13 Protocol-based VLAN Membership ................................................................................................................. 141

4.7 Spanning Tree Protocol ........................................................................................................................... 142 4.7.1 Theory ............................................................................................................................................................... 142 4.7.2 STP System Configuration ................................................................................................................................ 148 4.7.3 Bridge Status ..................................................................................................................................................... 150 4.7.4 CIST Port Configuration..................................................................................................................................... 151 4.7.5 MSTI Priorities ................................................................................................................................................... 154 4.7.6 MSTI Configuration ............................................................................................................................................ 155 4.7.7 MSTI Ports Configuration .................................................................................................................................. 156 4.7.8 Port Status ......................................................................................................................................................... 158 4.7.9 Port Statistics ..................................................................................................................................................... 159

4.8 Multicast .................................................................................................................................................... 160 4.8.1 IGMP Snooping ................................................................................................................................................. 160 4.8.2 Profile Table ....................................................................................................................................................... 164 4.8.3 Address Entry .................................................................................................................................................... 165

User’s Manual

6

4.8.4 IGMP Snooping Configuration ........................................................................................................................... 166 4.8.5 IGMP Snooping VLAN Configuration ................................................................................................................. 168 4.8.6 IGMP Snooping Port Group Filtering ................................................................................................................. 170 4.8.7 IGMP Snooping Status ...................................................................................................................................... 171 4.8.8 IGMP Group Information .................................................................................................................................... 174 4.8.9 IGMPv3 Information ........................................................................................................................................... 175 4.8.10 MLD Snooping Configuration........................................................................................................................... 176 4.8.11 MLD Snooping VLAN Configuration ................................................................................................................ 177 4.8.12 MLD Snooping Port Group Filtering ................................................................................................................. 179 4.8.13 MLD Snooping Status ...................................................................................................................................... 180 4.8.14 MLD Group Information ................................................................................................................................... 183 4.8.15 MLDv2 Information .......................................................................................................................................... 184 4.8.16 MVR (Multicaset VLAN Registration) ............................................................................................................... 185 4.8.17 MVR Status ..................................................................................................................................................... 188 4.8.18 MVR Groups Information ................................................................................................................................. 189 4.8.19 MVR SFM Information ..................................................................................................................................... 190

4.9 Quality of Service ..................................................................................................................................... 191 4.9.1 Understanding QoS ........................................................................................................................................... 191 4.9.2 Port Policing ...................................................................................................................................................... 192 4.9.3 Port Classification .............................................................................................................................................. 193 4.9.4 Port Scheduler ................................................................................................................................................... 195 4.9.5 Port Shaping ...................................................................................................................................................... 196

4.9.5.1 QoS Egress Port Schedule and Shapers ................................................................................................ 197 4.9.6 Port Tag Remarking ........................................................................................................................................... 199

4.9.6.1 QoS Egress Port Tag Remarking............................................................................................................. 200 4.9.7 Port DSCP ......................................................................................................................................................... 201 4.9.8 DSCP-based QoS ............................................................................................................................................. 203 4.9.9 DSCP Translation .............................................................................................................................................. 204 4.9.10 DSCP Classification......................................................................................................................................... 205 4.9.11 QoS Control List .............................................................................................................................................. 206

4.9.11.1 QoS Control Entry Configuration ........................................................................................................... 208 4.9.12 QCL Status ...................................................................................................................................................... 210 4.9.13 Storm Control Configuration ............................................................................................................................ 212 4.9.14 QoS Statistics .................................................................................................................................................. 213 4.9.15 Voice VLAN Configuration ............................................................................................................................... 214 4.9.16 Voice VLAN OUI Table..................................................................................................................................... 216

4.10 Access Control List ................................................................................................................................ 217 4.10.1 Access Control List Status ............................................................................................................................... 217 4.10.2 Access Control List Configuration .................................................................................................................... 219 4.10.3 ACE Configuration ........................................................................................................................................... 221

User’s Manual

7

4.10.4 ACL Ports Configuration .................................................................................................................................. 231 4.10.5 ACL Rate Limiter Configuration ....................................................................................................................... 233

4.11 Authentication ......................................................................................................................................... 234 4.11.1 Understanding IEEE 802.1X Port-based Authentication .................................................................................. 235 4.11.2 Authentication Configuration ............................................................................................................................ 238 4.11.3 Network Access Server Configuration.............................................................................................................. 239 4.11.4 Network Access Overview ............................................................................................................................... 250 4.11.5 Network Access Statistics ................................................................................................................................ 251 4.11.6 RADIUS ........................................................................................................................................................... 258 4.11.7 TACACS+ ........................................................................................................................................................ 260 4.11.8 RADIUS Overview ........................................................................................................................................... 261 4.11.9 RADIUS Details ............................................................................................................................................... 263 4.11.10 Windows Platform RADIUS Server Configuration .......................................................................................... 269 4.11.11 802.1X Client Configuration ........................................................................................................................... 274

4.12 Security ................................................................................................................................................... 277 4.12.1 Port Limit Control ............................................................................................................................................. 277 4.12.2 Access Management ....................................................................................................................................... 281 4.12.3 Access Management Statistics ........................................................................................................................ 282 4.12.4 HTTPs ............................................................................................................................................................. 283 4.12.5 SSH ................................................................................................................................................................. 284 4.12.6 Port Security Status ......................................................................................................................................... 285 4.12.7 Port Security Detail .......................................................................................................................................... 287 4.12.8 DHCP Snooping .............................................................................................................................................. 288 4.12.9 Snooping Table ................................................................................................................................................ 290 4.12.10 IP Source Guard Configuration ...................................................................................................................... 290 4.12.11 IP Source Guard Static Table ......................................................................................................................... 292 4.12.12 Dynamic IP Source Guard Table.................................................................................................................... 293 4.12.13 ARP Inspection .............................................................................................................................................. 294 4.12.14 ARP Inspection Static Table ........................................................................................................................... 296 4.12.15 Dynamic ARP Inspection Table ...................................................................................................................... 296

4.13 MAC Address Table ................................................................................................................................ 298 4.13.1 MAC Table Configuration ................................................................................................................................. 298 4.13.2 MAC Address Table Status .............................................................................................................................. 300

4.14 LLDP ........................................................................................................................................................ 302 4.14.1 Link Layer Discovery Protocol ......................................................................................................................... 302 4.14.2 LLDP Configuration ......................................................................................................................................... 302 4.14.3 LLDP MED Configuration ................................................................................................................................ 305 4.14.4 LLDP-MED Neighbor ....................................................................................................................................... 311 4.14.5 Neighbor .......................................................................................................................................................... 315

User’s Manual

8

4.14.6 Port Statistics ................................................................................................................................................... 316

4.15 Network Diagnostics .............................................................................................................................. 319 4.15.1 Ping ................................................................................................................................................................. 320 4.15.2 IPv6 Ping ......................................................................................................................................................... 321 4.15.3 Remote IP Ping Test ........................................................................................................................................ 322 4.15.4 Cable Diagnostics ............................................................................................................................................ 323

4.16 Power over Ethernet .............................................................................................................................. 325 4.16.1 Power over Ethernet Powered Device ............................................................................................................. 325 4.16.2 System Configuration ...................................................................................................................................... 327 4.16.3 Power Over Ethernet Configuration ................................................................................................................. 328 4.16.4 Port Sequential ................................................................................................................................................ 330 4.16.5 Port Configuration ............................................................................................................................................ 331 4.16.6 PoE Status....................................................................................................................................................... 333 4.16.7 PoE Schedule .................................................................................................................................................. 334 4.16.8 LLDP PoE Neighbours..................................................................................................................................... 337 4.16.10 PoE Alive Check Configuration ...................................................................................................................... 338

4.17 Loop Protection ...................................................................................................................................... 340 4.17.1 Configuration ................................................................................................................................................... 340 4.17.2 Loop Protection Status .................................................................................................................................... 342

4.18 RMON....................................................................................................................................................... 343 4.18.1 RMON Alarm Configuration ............................................................................................................................. 343 4.18.2 RMON Alarm Status ........................................................................................................................................ 345 4.18.3 RMON Event Configuration ............................................................................................................................. 346 4.18.4 RMON Event Status ........................................................................................................................................ 347 4.18.5 RMON History Configuration ........................................................................................................................... 348 4.18.6 RMON History Status ...................................................................................................................................... 349 4.18.7 RMON Statistics Configuration ........................................................................................................................ 350 4.18.8 RMON Statistics Status ................................................................................................................................... 351

4.19 PTP ........................................................................................................................................................... 353 4.19.1 PTP Configuration ........................................................................................................................................... 353 4.19.2 PTP Status ...................................................................................................................................................... 357

4.20 Ring.......................................................................................................................................................... 358 4.20.1 MEP Configuration .......................................................................................................................................... 359 4.20.2 Detailed MEP Configuration ............................................................................................................................ 360 4.20.3 Ethernet Ring Protocol Switch ......................................................................................................................... 363 4.20.4 Ethernet Ring Protocol Switch Configuration ................................................................................................... 365 4.20.5 Ring Wizard ..................................................................................................................................................... 368 4.20.6 Ring Wizard Example: ..................................................................................................................................... 369

User’s Manual

9

4.21.1 LCD Management ........................................................................................................................................... 371

4.22 ONVIF....................................................................................................................................................... 373 4.22.1 ONVIF Device Search ..................................................................................................................................... 373 4.22.2 ONVIF Device List ........................................................................................................................................... 374 4.22.3 Map Upload / Edit ............................................................................................................................................ 376 4.22.4 Floor Map ........................................................................................................................................................ 377

5. SWITCH OPERATION ....................................................................................................... 378

5.1 Address Table ........................................................................................................................................... 378

5.2 Learning .................................................................................................................................................... 378

5.3 Forwarding & Filtering ............................................................................................................................. 378

5.4 Store-and-Forward ................................................................................................................................... 378

5.5 Auto-Negotiation ...................................................................................................................................... 379

6. TROUBLESHOOTING ....................................................................................................... 380

APPENDIX A: Networking Connection ............................................................................... 381

A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T ....................................................... 381

A.2 10/100Mbps, 10/100BASE-TX ................................................................................................................. 381

APPENDIX B : GLOSSARY .................................................................................................. 383

User’s Manual

10

1. INTRODUCTION

The descriptions of PLANET L2+ Industrial Wall-mount Managed Switch series, such as WGS-5225-8P2S, WGS-5225-8P2SV, and WGS-5225-8T2SV are as follows:

WGS-5225-8P2S Industrial L2+ 8-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Wall-mount Managed Switch

WGS-5225-8P2SV Industrial L2+ 8-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Wall-mount Managed Switch

with LCD Touch Screen

WGS-5225-8T2SV Industrial L2+ 8-Port 10/100/1000T + 2-Port 100/1000X SFP Wall-mount Managed Switch with LCD

Touch Screen

“Wall-mount Managed Switch” is used as an alternative name for the above models in this user’s manual.

Model Name 10/100/1000T Copper Ports

802.3at PoE Ports

100/1000X SFP Ports 2.4’’ LCD

WGS-5225-8T2SV 8 - 2 ■ WGS-5225-8P2SV 8 8 2 ■ WGS-5225-8P2S 8 8 2 -

1.1 Packet Contents Open the box of the Wall-mount Managed Switch and carefully unpack it. The box should contain the following items:

Model Name

Item

WGS-5225-8P2S WGS-5225-8P2SV,

WGS-5225-8T2SV

The Wall-mount Managed Switch ■ ■ ■

Quick Installation Guide ■ ■ ■

DIN-rail Kit ■ ■ ■

Wall-mounted Kit ■ ■ ■

Magnet Kit ■ ■ ■

SFP Dust Caps 2 2 2

RJ45 Dust Caps 8 8 8

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

User’s Manual

11

1.2 Product Description

Wall-mount PoE Managed Switch with Advanced L2+/L4 Switching and Security

PLANET WGS-5225 Series is an Industrial Wall-mount Managed Switch with LCD Touch Screen featuring PoE or

non-PoE models to improve the availability of industrial applications. It provides IPv6/IPv4 dual stack management and

built-in L2+/L4 Gigabit switching engine along with eight 10/100/1000BASE-T ports and two additional

1000BASE-X SFP ports. The PoE model features 36-watt PoE and a total power budget of up to 240 watts for different

kinds of PoE applications. With operating temperature ranging from -20 to 70 degrees C in a compact but rugged IP30 metal

housing, the WGS-5225 Series is an ideal solution to meet the demand for the following network applications:

Building/Home automation network

Internet of things (IoT)

IP surveillance

User’s Manual

12

Intuitive LCD Control (WGS-5225-8P2SV/ WGS-5225-8T2SV) The WGS-5225 Series comes with an intuitive touch panel on its front panel that facilitates the Ethernet or PoE PD

management that greatly promotes management efficiency in large-scale networks, such as enterprises, hotels, shopping malls,

government buildings, and other public areas. It also features the following special management and status functions:

■ IP address, VLAN and QoS configuration

■ PoE management and status

■ Port management and status, and SFP information

■ Troubleshooting: cable diagnostic and remote IP ping

■ Maintenance: reboot, factory default and save configuration

Redundant Ring, Fast Recovery for Critical Network Applications The WGS-5225 Series supports redundant ring technology and features strong, rapid self-recovery capability to prevent

interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection

Switching) technology, Spanning Tree Protocol (802.1s MSTP), and dual power input system into customer’s industrial

automation network to enhance system reliability and uptime in harsh factory environments. In a certain simple ring network, the

recovery time of data link can be as fast as 20ms.

User’s Manual

13

Convenient and Smart ONVIF Devices with Detection Feature (WGS-5225-8P2S/8P2SV only) PLANET has newly developed an awesome feature -- ONVIF Support -- which is specifically designed for co-operating with

video IP surveillances. From the WGS-5225 Series’ GUI, you just need one click to search and show all of the ONVIF devices

via network application. In addition, you can upload floor images to the switch and can remotely locate where the PDs are.

Moreover, you can get real-time surveillance information and online/offline status; the PoE reboot can be controlled from the

GUI.

Built-in Unique PoE Functions for Powered Devices Management (WGS-5225-8P2S/8P2SV only) As it is the managed PoE switch for surveillance, wireless and VoIP networks, the WGS-5225 Series features the following

special PoE management functions:

PD alive check Scheduled power recycling PoE schedule PoE usage monitoring

Intelligent Powered Device Alive Check (WGS-5225-8P2S/8P2SV only) The WGS-5225 Series can be configured to monitor connected PD status in real time via ping action. Once the PD stops

working and responding, the WGS-5225 Series will resume the PoE port power and bring the PD back to work. It will greatly

enhance the network reliability through the PoE port resetting the PD’s power source and reducing administrator management

burden.

User’s Manual

14

Scheduled Power Recycling (WGS-5225-8P2S/8P2SV only) The WGS-5225 Series allows each of the connected PoE IP cameras or PoE wireless access points to reboot at a specific time

each week. Therefore, it will reduce the chance of IP camera or AP crash resulting from buffer overflow.

PoE Schedule for Energy Saving (WGS-5225-8P2S/8P2SV only) Under the trend of energy saving worldwide and contributing to environmental protection, the WGS-5225 Series can effectively

control the power supply besides its capability of giving high watts power. The “PoE schedule” function helps you to enable or

disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or

enterprises save power and budget. It also increases security by powering off PDs that should not be in use during

non-business hours.

User’s Manual

15

Innovative Wall-mount Installation

The WGS-5225 Series is specially designed to be installed in a narrow environment, such as wall enclosure or electric weak

box. The compact, flat and wall-mounted design fits easily in any space-limited location. It adopts the user-friendly “Front Access” design, making the installing, cable wiring, LED monitoring and maintenance of the WGS-5225 Series placed in an enclosure very convenient for technicians. The WGS-5225 Series can be installed by fixed wall mounting, magnetic wall mounting or DIN-rail mounting, thereby making its usability more flexible.

SMTP/SNMP Trap Event Alert The WGS-5225 Series provides event alert function to help to diagnose the abnormal device owing to whether or not there is a

break of the network connection, or the rebooting response.

Layer 3 IPv4 and IPv6 Software VLAN Routing for Secure and Flexible Management

To help customers stay on top of their businesses, the WGS-5225 Series not only provides ultra high transmission performance

and excellent Layer 2 technologies, but also IPv4/IPv6 software VLAN routing feature which allows to cross over different

VLANs and different IP addresses for the purpose of having a highly-secure, flexible management and simpler networking

application.

User’s Manual

16

Robust Layer 2 Features

The WGS-5225 Series can be programmed for advanced switch management functions such as dynamic port link aggregation,

Q-in-Q VLAN, private VLAN, Rapid Spanning Tree Protocol, Layer 2 to Layer 4 QoS, bandwidth control and IGMP snooping.

The WGS-5225 Series provides 802.1Q tagged VLAN, and the VLAN groups allowed will be maximally up to 255. Via

aggregation of supporting ports, the WGS-5225 Series allows the operation of a high-speed trunk combining multiple ports. It

enables a maximum of up to 2 trunk groups with 2 ports per trunk group, and supports fail-over as well.

Efficient Management

For efficient management, the WGS-5225 Series is equipped with console, Web and SNMP management interfaces. With the

built-in Web-based management interface, the WGS-5225 Series offers an easy-to-use, platform-independent management

and configuration facility. For text-based management, the WGS-5225 Series can be accessed via Telnet and the console port.

Moreover, it also offers secure remote management via any standard-based management software by supporting SNMPv3

connection which encrypts the packet content at each session.

Powerful Security

The WGS-5225 Series offers a comprehensive Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It

can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or

defined typical network applications. Its protection mechanism also comprises 802.1x Port-based and MAC-based user and

device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user

privacy. The network administrators can now construct highly-secure corporate networks with considerably less time and effort

than before.

User’s Manual

17

Modbus TCP Provides Flexible Network Connectivity for Factory Automation

With the supported Modbus TCP/IP protocol, the WGS-5225 Series can easily integrate with SCADA systems, HMI systems

and other data acquisition systems in factory floors. It enables administrators to remotely monitor the industrial Ethernet switch’s

operating information, port information and communication status, thus easily achieving enhanced monitoring and maintenance

of the entire factory.

Flexibility and Extension Solution

The additional four mini-GBIC slots built in the WGS-5225 Series support dual speed, 100BASE-FX and 1000BASE-SX/LX SFP

(Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP

transceiver according to not only the transmission distance but also the transmission speed required. The distance can be

extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited

for applications within the enterprise data centers and distributions.

Intelligent SFP Diagnosis Mechanism

The WGS-5225 Series supports SFP-DDM (Digital Diagnostic Monitor) function that greatly helps network administrator to

easily monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias

current, and transceiver supply voltage.

1588 Time Protocol for Industrial Computing Networks

The WGS-5225 Series is ideal for telecom and Carrier Ethernet applications, supporting MEF service delivery and timing over

packet solutions for IEEE 1588 and synchronous Ethernet.

User’s Manual

18

1.3 How to Use This Manual This User’s Manual is structured as follows:

Section 2, INSTALLATION

The section explains the functions of the Wall-mount Managed Switch and how to physically install the Wall-mount

Managed Switch.

Section 3, SWITCH MANAGEMENT

The section contains the information about the software function of the Wall-mount Managed Switch.

Section 4, WEB CONFIGURATION

The section explains how to manage the Wall-mount Managed Switch by Web interface.

Section 5, SWITCH OPERATION

The chapter explains how to do the switch operation of the Wall-mount Managed Switch.

Section 6, TROUBLESHOOTING

The chapter explains how to do troubleshooting of the Wall-mount Managed Switch.

Appendix A

The section contains cable information of the Wall-mount Managed Switch.

Appendix B

The section contains glossary information of the Wall-mount Managed Switch.

User’s Manual

19

1.4 Product Features Physical Port (WGS-5225-8P2SV/WGS-5225-8P2S)

8 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ Injector

2 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection

Physical Port (WGS-5225-8T2SV)

8 10/100/1000BASE-T Gigabit Ethernet RJ45 ports

2 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection

Power over Ethernet (WGS-5225-8P2SV/WGS-5225-8P2S)

Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE

Up to 8 IEEE 802.3af/802.3at devices powered

Supports PoE power up to 36 watts for each PoE port

Auto detects powered device (PD)

Circuit protection prevents power interference between ports

Remote power feeding up to 100m

PoE management features − Total PoE power budget control − Per port PoE function enable/disable − PoE admin-mode control − PoE port power feeding priority − Per PoE port power limit − PD classification detection

Intelligent PoE features − Temperature threshold control − PoE usage threshold control − PD alive check − PoE schedule

Layer 2 Features

Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)

High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize

the network bandwidth

Storm Control support

− Broadcast/Multicast/Unicast

Supports VLAN

− IEEE 802.1Q tagged VLAN

− Up to 255 VLANs groups, out of 4094 VLAN IDs

− Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)

− Private VLAN Edge (PVE)

− Protocol-based VLAN

User’s Manual

20

− MAC-based VLAN

− Voice VLAN

Supports Spanning Tree Protocol

− IEEE 802.1D Spanning Tree Protocol (STP)

− IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

− IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN

− BPDU Guard

Supports Link Aggregation

− 802.3ad Link Aggregation Control Protocol (LACP)

− Cisco ether-channel (static trunk)

− Maximum 2 trunk groups with 2 ports per trunk group

− Up to 2Gbps bandwidth (duplex mode)

Provides port mirror (1-to-1)

Port mirroring to monitor the incoming or outgoing traffic on a particular port

Loop protection to avoid broadcast loops

Supports ERPS (Ethernet Ring Protection Switching)

Layer 3 IP Routing Features Supports maximum 32 static routes and route summarization

Quality of Service

Ingress Shaper and Egress Rate Limit per port bandwidth control

8 priority queues on all switch ports

Traffic classification

- IEEE 802.1p CoS

- IP TOS/DSCP/IP precedence

- IP TCP/UDP port number

- Typical network application

Strict priority and Weighted Round Robin (WRR) CoS policies

Supports QoS and In/Out bandwidth control on each port

Traffic-policing on the switch port

DSCP remarking

Multicast

Supports IGMP snooping v1, v2 and v3

Supports MLD snooping v1 and v2

Querier mode support

IGMP snooping port filtering

MLD snooping port filtering

MVR (Multicast VLAN Registration)

User’s Manual

21

Security

IEEE 802.1x Port-based/MAC-based network access authentication

Built-in RADIUS client to cooperate with the RADIUS servers

TACACS+ login users access authentication

RADIUS/TACACS+ users access authentication

IP-based Access Control List (ACL)

MAC-based Access Control List

Source MAC/IP address binding

DHCP snooping to filter distrusted DHCP messages

Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

IP Source Guard prevents IP spoofing attacks

IP address access management to prevent unauthorized intruder

Management

Switch Management Interfaces

- Telnet Command Line Interface

- Web switch management

- SNMP v1 and v2c switch management

- SSH/SSL and SNMP v3 secure access - 2.4-inch color LCD touch screen (WGS-5225-8P2SV/WGS-5225-8T2SV)

Four RMON groups (history, statistics, alarms, and events)

IPv6 IP address/NTP/DNS management

Built-in Trivial File Transfer Protocol (TFTP) client

BOOTP and DHCP for IP address assignment

Firmware upload/download via HTTP/TFTP

DHCP Relay and DHCP Option 82

User Privilege levels control

Network Time Protocol (NTP)

Link Layer Discovery Protocol (LLDP)

SFP-DDM (Digital Diagnostic Monitor)

Cable diagnostic technology provides the mechanism to detect and report potential cabling issues

Reset button for system reboot or reset to factory default PLANET Smart Discovery Utility for deployment management

User’s Manual

22

1.5 Product Specifications

Product WGS-5225-8P2SV WGS-5225-8P2S WGS-5225-8T2SV

Hardware Specifications

Copper Ports 8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports

SFP/mini-GBIC Slots 2 1000BASE-SX/LX/BX SFP interfaces (Port-9 to Port-10) Compatible with 100BASE-FX SFP

PoE Injector Port 8 ports with 802.3at/af PoE injector function with Port-1 to Port-8

－

Switch Architecture Store-and-Forward

Switch Fabric 20Gbps/non-blocking

Throughput (packet per second) 14.88Mpps@ 64 bytes packet

Address Table 8K entries, automatic source address learning and aging

Shared Data Buffer 4Mbits

Flow Control IEEE 802.3x pause frame for full duplex Back pressure for half duplex

Jumbo Frame 9Kbytes

Reset Button < 5 sec: System reboot > 5 sec: Factory default

ESD Protection 6KV DC

Enclosure IP30 aluminum case

Installation DIN rail kit and wall-mount

Connector

Removable 3-pin terminal block for power input

- Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-)

- Pin 3 for earth ground

DC power jack with 2.0mm central pole

LED Indicator

System:

PWR(Green)

Ring (Green)

Ring Owner (Green)

Per 10/100/1000T RJ45 PoE+ Ports:

PoE-in-Use (Orange)

LNK/ACT (Green)

Per SFP Interface:

100 LNK/ACT (Orange)

1000 LNK/ACT (Green)

System:

PWR(Green)

Ring (Green)

Ring Owner (Green)

Per 10/100/1000T RJ45

10/100LNK/ACT (Green)


Per SFP Interface:


1000 LNK/ACT (Green)

Dimensions (W x D x H) 180 x 24.4 x 140 mm

Weight 686g 681g 642g

Power Requirements Dual 48~56V DC (>51V DC for PoE+ output recommended)

Dual 12~48V DC

Power Consumption Max. 7.2 watts/24.7BTU

(Power on without any

Max. 6.6 watts/22.6BTU




User’s Manual

23

connection)

Max. 251 watts/861.2BTU

(Full loading with PoE

function)

connection)

Max. 250.4

watts/859.1BTU (Full

loading with PoE function)

connection)


(Full loading with Ethernet)

Power Over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE －

PoE Power Supply Type End-span －

PoE Power Output

IEEE 802.3af Standard - Per port 48V~51V DC (depending on the power supply), max. 15.4 watts IEEE 802.3at Standard - Per port 51V~56V DC (depending on the power supply), max. 36 watts

－

Power Pin Assignment 1/2(+), 3/6(-) －

PoE Power Budget 240W maximum (depending on power input) －

Max. Number of Class 2 PDs 8 －



Layer 2 Function

Basic Management Interfaces Console; Telnet; Web browser; SNMP v1, v2c

Secure Management Interfaces SSH, SSL, SNMP v3

Port Configuration

Port disable/enable Auto-negotiation 10/100/1000Mbps full and half duplex mode selection Flow control disable/enable Power saving mode control

Port Status Display each port’s speed duplex mode, link status, flow control status, auto negotiation status, trunk status

Port Mirroring TX/RX/both 1 to 1 monitor

VLAN

802.1Q tag-based VLAN, up to 255 VLAN groups Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN MVR (Multicast VLAN Registration) Up to 255 VLAN groups, out of 4094 VLAN IDs

Link Aggregation IEEE 802.3ad LACP/static trunk Supports 2 trunk groups with 2 ports per trunk group

QoS

Traffic classification based, strict priority and WRR 8-level priority for switching

- Port number - 802.1p priority

- 802.1Q VLAN tag - DSCP/TOS field in IP packet

User’s Manual

24

IGMP Snooping IGMP (v1/v2/v3) snooping, up to 255 multicast groups IGMP querier mode support

MLD Snooping MLD (v1/v2) snooping, up to 255 multicast groups MLD querier mode support

Access Control List IP-based ACL/MAC-based ACL Up to 256 entries

Bandwidth Control Per port bandwidth control

Ingress: 500Kb~1000Mbps Egress: 500Kb~1000Mbps

SNMP MIBs

RFC 1213 MIB-II IF-MIB RFC 1493 Bridge MIB RFC 1643 Ethernet MIB RFC 2863 Interface MIB RFC 2665 Ether-Like MIB RFC 2819 RMON MIB (Groups 1, 2, 3 and 9) RFC 2737 Entity MIB RFC 2618 RADIUS Client MIB RFC 2933 IGMP-STD-MIB RFC 3411 SNMP-Frameworks-MIB IEEE 802.1X PAE LLDP MAU-MIB

Layer 3 Function

IP Interfaces Max. 8 VLAN interfaces

Routing Table Max. 32 routing entries

Routing Protocols IPv4 software static routing IPv6 software static routing

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (free fall)

IEC60068-2-27 (shock)

IEC60068-2-6 (vibration)

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX/100BASE-FX

IEEE 802.3z Gigabit SX/LX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3x flow control and back pressure

IEEE 802.3ad port trunk with LACP

IEEE 802.1D Spanning Tree Protocol

IEEE 802.1w Rapid Spanning Tree Protocol

IEEE 802.1s Multiple Spanning Tree Protocol

IEEE 802.1p Class of Service

IEEE 802.1Q VLAN tagging

IEEE 802.1X Port Authentication Network Control

Standards Compliance

User’s Manual

25

IEEE 802.1ab LLDP

IEEE 802.3af Power over Ethernet (WGS-5225-8P2S and WGS-5225-8P2SV)

IEEE 802.3at Power over Ethernet Plus(WGS-5225-8P2S and WGS-5225-8P2SV)

ITU-T G.8032 Ethernet Ring Protection Switching

RFC 768 UDP

RFC 793 TFTP

RFC 791 IP

RFC 792 ICMP

RFC 2068 HTTP

RFC 1112 IGMP v1

RFC 2236 IGMP v2

Environment

Operating Temperature -20 ~ 70 degrees C -40 ~ 75 degrees C -20 ~ 70 degrees C

Storage Temperature -20 ~ 70 degrees C -40 ~ 85 degrees C -20 ~ 70 degrees C

Humidity 5 ~ 95% (non-condensing)

User’s Manual

26

2. INSTALLATION

2.1 Hardware Description The Wall-mount Managed Switch provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps and automatically distinguishes the speed of incoming connection.

This section describes the hardware features of Wall-mount Managed Switch. For easier management and control of the Wall-mount Managed Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Wall-mount Managed Switch, read this chapter carefully.

2.1.1 The front panel provides a simple interface monitoring the Managed Switch. Figures 2-1-1 to 2-1-3 show the front panels of the

Wall-mount Managed Switches.

WGS-5225-8P2SV

Figure 2-1-1: Front Panel of WGS-5225-8P2SV

User’s Manual

27

WGS-5225-8P2S

Figure 2-1-2: Front Panel of WGS-5225-8P2S

WGS-5225-8T2SV

Figure 2-1-3: Front Panel of WGS-5225-8T2SV

■ 1 Gigabit TP interface

10/100/1000BASE-T Copper, RJ45 twisted-pair: Up to 100 meters.

■ 1 Gigabit SFP slot

1000BASE-SX/LX/BX mini-GBIC slot, SFP+ (Small Factor Pluggable Plus) Transceiver module supports from 300 meters

(multi-mode fiber) up to 10 kilometers (single mode fiber)

User’s Manual

28

■ Reset button

The bottom of the Wall-mount Managed Switch comes with a reset button designed for rebooting the Managed Switch

without turning off and on the power. The following is the summary table of reset button functions:

Reset Button Pressed and Released Function

< 5 sec: System Reboot Reboot the Managed Switch.

> 5 sec: Factory Default

Reset the Managed Switch to Factory Default configuration.

The Wall-mount Managed Switch will then reboot and load

the default settings as shown below: 。 Default Username: admin

。 Default Password: admin

。 Default IP Address: 192.168.0.100

。 Subnet Mask: 255.255.255.0

。 Default Gateway: 192.168.0.254

User’s Manual

29

2.1. LED Indications

WGS-5225-8P2S/WGS-5225-8P2SV

System

LED Color Function

PWR Green Lights to indicate that the Switch has power.

SYS Green Lights to indicate the system is working.

Ring Green Lights to indicate that the ERPS Ring has been created successfully.

R.O. Green Lights to indicate that Switch has enabled Ring Owner.

Per 10/100/1000BASE-T Port

LED Color Function

LNK/ACT Green Lights: To indicate the link through that port is successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

PoE Orange Lights: To indicate the port is providing DC in-line power.

Off: To indicate the connected device is not a PoE Powered Device (PD)

Per SFP Interface

LED Color Function

1000

LNK/ACT Green

Lights: To indicate the link through that port is successfully established at 1000Mbps.


100

LNK/ACT Orange



User’s Manual

30

WGS-5225-8T2SV

System

LED Color Function

PWR Green Lights to indicate that the Switch has power.

SYS Green Lights to indicate the system is working.

Ring Green Lights to indicate that the ERPS Ring has been created successfully.

R.O. Green Lights to indicate that Switch has enabled Ring Owner.

Per 10/100/1000BASE-T Port

LED Color Function

LNK/ACT Green Lights: To indicate the link through that port is successfully established at 10/100Mbps.


1000 LNK/ACT

Orange Lights: To indicate the link through that port is successfully established at 1000Mbps.


Per SFP Interface

LED Color Function

1000

LNK/ACT Green



100

LNK/ACT Orange



User’s Manual

31

2.1. Wiring Power Input The Wall-mount Managed Switch features a strong dual power input system (Terminal block and DC jack) incorporated into

customer’s automation network to enhance system reliability and uptime.

Power Input

Range Model

3-pin Terminal Block DC Jack

WGS-5225-8T2SV 12~48V DC 12~48V DC

WGS-5225-8P2SV 48~56V DC 48~56V DC

WGS-5225-8P2S 48~56V DC 48~56V DC

To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch, simply follow the following steps:

Step 1: Insert positive DC power wire into V+, negative DC power wire into V-, and grounding wire into Ground.

User’s Manual

32

Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug them into the Wall-mount Managed

switch

1. The wire gauge for the terminal block should be in the range of 12 ~ 24 AWG.

2. When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock.

2.2 Installing the Wall-mount Managed Switch This section describes how to install your Wall-mount Managed Switch and make connections. Please read the following topics

and perform the procedures in the order being presented.

2.2.1 Wall-mount Installation

To install the Wall-mount Managed Switch on the wall, simply follow the following steps:

Step 1: There are 4 holes with 8mm diameter on the wall; the distance between the 2 holes is 165mm and the line through them

must be horizontal.

Step 2: Install a conductor pipe inside the board hole and flush the edge of the conductor pipe with the wall surface.

Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch is between bolts and conductor pipe, as shown below.

User’s Manual

33

2.2.2 Magnet Installation

To install the Wall-mount Managed Switch on a magnetic surface, simply follow the following diagram:

2.2.3 DIN-rail Installation

The DIN-rail kit is included in the package. When the wall-mount application for the Wall-mount Managed Switch needs to be replaced with DIN-rail application, please refer to the following figures to screw the DIN-rail on the Wall-mount Managed Switch. To hang up the Wall-mount Managed Switch, follow the steps below:

Step 1: Screw the DIN-rail on the Wall-mount Managed Switch.

User’s Manual

34

Step 2: Lightly insert the button of DIN-rail into the track.

Step 3: Check whether the DIN-rail is tightly on the track.

User’s Manual

35

2.2.4 Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and

hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Managed Switch,

as Figure 2-2-4 shows..

Figure 2-2-4: Plug in the SFP/SFP+ Transceiver

User’s Manual

36

2.2.5 Approved PLANET SFP/SFP+ Transceivers

PLANET Managed Switch supports both single mode and multi-mode SFP transceivers. The following list of approved PLANET

SFP transceivers is correct at the time of publication:

Gigabit Ethernet Transceiver (1000BASE-X SFP)

Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.

MGB-GT 1000 Copper -- 100m -- 0 ~ 60 degrees C

MGB-SX 1000 LC Multi Mode 550m 850nm 0 ~ 60 degrees C

MGB-SX2 1000 LC Multi Mode 2km 1310nm 0 ~ 60 degrees C

MGB-LX 1000 LC Single Mode 10km 1310nm 0 ~ 60 degrees C

MGB-L30 1000 LC Single Mode 30km 1310nm 0 ~ 60 degrees C




MGB-TSX 1000 LC Multi Mode 550m 850nm -40 ~ 75 degrees C

MGB-TLX 1000 LC Single Mode 10km 1310nm -40 ~ 75 degrees C

MGB-TL30 1000 LC Single Mode 30km 1310nm -40 ~ 75 degrees C

MGB-TL70 1000 LC Single Mode 70km 1550nm -40 ~ 75 degrees C

Gigabit Ethernet Transceiver (1000BASE-BX, Single Fiber Bi-directional SFP)

Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (TX/RX) Operating Temp.

MGB-LA10 1000 WDM(LC) Single Mode 10km 1310nm/1550nm 0 ~ 60 degrees C

MGB-LB10 1000 WDM(LC) Single Mode 10km 1550nm/1310nm 0 ~ 60 degrees C







MGB-TLA10 1000 WDM(LC) Single Mode 10km 1310nm/1550nm -40 ~ 75 degrees C

MGB-TLB10 1000 WDM(LC) Single Mode 10km 1550nm/1310nm -40 ~ 75 degrees C







User’s Manual

37

It is recommended to use PLANET SFP on the Wall-mount Managed Switch. If you insert an SFP

transceiver that is not supported, the Wall-mount Managed Switch will not recognize it.

1. Before we connect the Wall-mount Managed Switch to the other network device, we have to make sure both sides of the

SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to

1000BASE-LX.

2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.

To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male

duplex LC connector type.

To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male

duplex LC connector type.

Connect the Fiber Cable

1. Insert the duplex LC connector into the SFP transceiver.

2. Connect the other end of the cable to a device with SFPtransceiver installed.

3. Check the LNK/ACT LED of the SFP slot on the front of the Wall-mount Managed Switch. Ensure that the SFP transceiver

is operating correctly.

4. Check the Link mode of the SFP port if the link fails. To function with some fiber-NICs or Media Converters, user has to set

the port Link mode to “100M Force” or “1000M Force”.

Remove the Transceiver Module

1. Make sure there is no network activity anymore.

2. Remove the Fiber-Optic Cable gently.

3. Lift up the lever of the MGB module and turn it to a horizontal position.

4. Pull out the module gently through the lever.

User’s Manual

38

Figure 2-2-5: How to Pull Out the SFP Transceiver

Never pull out the module without lifting up the lever of the module and turning it to a horizontal

position. Directly pulling out the module could damage the module and the SFP module slot of

the Wall-mount Managed Switch.

User’s Manual

39

3. SWITCH MANAGEMENT

This chapter explains the methods that you can use to configure management access to the Wall-mount Managed Switch. It

describes the types of management applications and the communication and management protocols that deliver data between

your management device (workstation or personal computer) and the system. It also contains information about port connection

options.

This chapter covers the following topics:

Requirements

Management Access Overview

Remote Telnet Access

Web Management Access

SNMP Access

Standards, Protocols, and Related Reading

3.1 Requirements

Workstation running Windows XP/2003, Vista, Windows 7/8/10, MAC OS X, Linux, Fedora, Ubuntu or other platform is compatible with TCP/IP protocols.

Workstation is installed with Ethernet NIC (Network Interface Card)

Ethernet Port

• Network cables -- Use standard network (UTP) cables with RJ45 connectors.

The above workstation is installed with Web browser and JAVA runtime environment Plug-in

It is recommended to use Internet Explore 8.0 or above to access Wall-mount Managed Switch.

User’s Manual

40

3.2 Management Access Overview The Wall-mount Managed Switch gives you the flexibility to access and manage it using any or all of the following methods:

Remote Telnet Interface

Web browser Interface

An external SNMP-based network management application

The remote Telnet and Web browser interfaces are embedded in the Wall-mount Managed Switch software and are available

for immediate use. Each of these management methods has their own advantages. Table 3-1 compares the three management

methods.

Method Advantages Disadvantages

Remote

Telnet

• Text-based

• Telnet functionality built into Windows

XP/2003, Vista, Windows 7/8/10

operating systems

• Can be accessed from any location

• Security can be compromised (hackers need

only know the IP address)

Web Browser • Ideal for configuring the switch remotely

• Compatible with all popular browsers

• Can be accessed from any location

• Most visually appealing


only know the IP address and subnet mask)

• May encounter lag times on poor connections

SNMP Agent • Communicates with switch functions at

the MIB level

• Based on open standards

• Requires SNMP manager software

• Least visually appealing of all three methods

• Some settings require calculations


only know the community name)

Table 3-1: Management Methods Comparison

User’s Manual

41

3.3 Remote Telnet Management The Wall-mount Managed Switch also supports telnet for remote management. The switch asks for user name and password

for remote login when using telnet; please use “admin” for both username and password.

Default IP address: 192.168.0.100 Username: admin Password: admin

Figure 3-3-1 Wall-mount Managed Switch Telnet Login Screen

3.4 Web Management and LCD Touch Screen The Wall-mount Managed Switch offers management features that allow users to manage the Wall-mount Managed Switch

from anywhere on the network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address

for the Wall-mount Managed Switch, you can access the Wall-mount Managed Switch’s Web interface applications directly

in your Web browser by entering the IP address of the Wall-mount Managed Switch.

Figure 3-4-1: Web Management

You can then use your Web browser to list and manage the Wall-mount Managed Switch configuration parameters from one

central location; the Web Management requires Microsoft Internet Explorer 8.0 or later.

User’s Manual

42

Figure 3-4-2: Web Main Screen of Wall-mount Managed Switch

LCD Touch Screen The WGS-5225-8P2SV and WGS-5225-8T2SV have a 2.4-inch color LCD touch screen with management functions. Tap the

LCD touch screen to wake the LCD touch screen.

Figure 3-4-3: To wake the LCD touch screen

User’s Manual

43

The factory default LCD configurations are shown as follows.

Default LCD: Enable Default Touch Screen: Enable Default Backlight Timeout: Enable Default Backlight Timeout Time: 300 Default Read Only Mode: Disable Default Screen: Main Menu Default Time Interval: 10 Default Color Scheme: Dark Default Pin Number: 1234

You can use the Web management interface and click LCD, and then in the LCD Management, change LCD configuration.

User’s Manual

44

3.5 SNMP-based Network Management You can use an external SNMP-based application to configure and manage the Wall-mount Managed Switch, such as SNMP

Network Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This management method requires

the SNMP agent on the Wall-mount Managed Switch and the SNMP Network Management Station to use the same

community string. This management method, in fact, uses two community strings: the get community string and the set

community string. If the SNMP Network Management Station only knows the set community string, it can read and write to the

MIBs. However, if it only knows the get community string, it can only read MIBs. The default gets and sets community strings for

the Wall-mount Managed Switch are public.

Figure 3-5: SNMP Management

User’s Manual

45

3.6 PLANET Smart Discovery Utility To easily list the Wall-mount Managed Switch in your Ethernet environment, the Planet Smart Discovery Utility from user’s

manual CD-ROM is an ideal solution. The following install instructions guide you to running the Planet Smart Discovery Utility.

1. Open the Planet Smart Discovery Utility in administrator PC.

2. Run this utility and the following screen appears.

Figure 3-6: Planet Smart Discovery Utility Screen

If there are two LAN cards or above in the same administrator PC, choose a different LAN card by using the “Select Adapter” tool.

3. Press “Refresh” button for the currently connected devices in the discovery list as the screen is shown as follows.

Figure 3-7: Planet Smart Discovery Utility Screen

User’s Manual

46

1. This utility shows all the necessary information from the devices, such as MAC Address, Device Name, firmware version

and Device IP Subnet address. A new password, IP Subnet address and description can be assigned to the devices.

2. After setup is completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning of

the 3 buttons above are shown below:

Update Device: use current setting on one single device. Update Multi: use current setting on choose multi-devices. Update All: use current setting on whole devices in the list.

The same functions mentioned above also can be found in “Option” tools bar.

3. To click the “Control Packet Force Broadcast” function, it allows new setting value to be assigned to the Web Smart

Switch under a different IP subnet address.

4. Press “Connect to Device” button and then the Web login screen appears in Figure 3-7.

5. Press “Exit” button to shut down the planet Smart Discovery Utility.

User’s Manual

47

4. WEB CONFIGURATION

This section introduces the configuration and functions of the Web-based management.

About Web-based Management The Wall-mount Managed Switch offers management features that allow users to manage the Wall-mount Managed Switch

from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

The Web-based Management supports Internet Explorer 7.0. It is based on Java Applets with an aim to reducing network

bandwidth consumption, enhancing access speed and presenting an easy viewing screen.

By default, IE7.0 or later version does not allow Java Applets to open sockets. The user has to

explicitly modify the browser setting to enable Java Applets to use network ports.

The Wall-mount Managed Switch can be configured through an Ethernet connection, making sure the manager PC must be set

on same the IP subnet address with the Wall-mount Managed Switch.

For example, the default IP address of the Wall-mount Managed Switch is 192.168.0.100, then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

If you have changed the default IP address of the Wall-mount Managed Switch to 192.168.1.1 wi

planet.com.ru · user’s manual . 3 . table of contents . 1. introduction

Documents