wap200e_v10_ug_c_web

8/8/2019 WAP200E_V10_UG_C_web

http://slidepdf.com/reader/full/wap200ev10ugcweb 1/46

USER GUIDE

BUSINESS SERIE

Wireless-G Exterior

Access Point with

Power Over Ethernet

Model: WAP200E

8/8/2019 WAP200E_V10_UG_C_web


i

About This Guide

Wireless-G Exterior Access Point with Power Over Ethernet

About This Guide

Icon Descriptions

While reading through the User Guide you may encountervarious icons designed to call attention to a speciic item.Below is a description o these icons:

NOTE: This check mark indicates that there isa note o interest and is something that youshould pay special attention to while using theproduct.

WARNING: This exclamation point indicatesthat there is a caution or warning and it is

something that could damage your property orproduct.

WEB: This globe icon indicates a noteworthywebsite address or e-mail address.

Online Resources

Most web browsers allow you to enter the web addresswithout adding the http:// in ront o the address. ThisUser Guide will reer to websites without including http://in ront o the address. Some older web browsers mayrequire you to add it.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Copyright and Trademarks

Speciications are subject to change without notice.Linksys, Cisco and the Cisco Logo are registered trademarksor trademarks o Cisco Systems, Inc. and/or its ailiates inthe U.S. and certain other countries. Copyright © 2008Cisco Systems, Inc. All rights reserved. Other brands andproduct names are trademarks or registered trademarkso their respective holders.

8/8/2019 WAP200E_V10_UG_C_web


ii

Table of Contents


Chapter 1: Introduction 1

Chapter 2: Planning Your Wireless Network 2

Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Network Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Example o a Simple Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 3: Product Overview 3

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

The Antenna Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 4: Installation 6

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Personal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

External Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 5: Quick Confguration Overview 8

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Accessing the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Navigating the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 6: Advanced Confguration 10

Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Setup > Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > Wireless Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

8/8/2019 WAP200E_V10_UG_C_web


iii

Table of Contents


Wireless Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Connection Control List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Wireless > VLAN & QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Administration > Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

AP Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Web Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Administration > Factory Deault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Factory Deault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Administration > Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Administration > Cong Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Cong Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Inormation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Status > System Perormance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

System Perormance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Appendix A: Troubleshooting 25

Appendix B: Wireless Security Checklist 28

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Appendix C: Glossary 29

Appendix D: Specifcations 33

Appendix E: Warranty and Regulatory Inormation 35

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

8/8/2019 WAP200E_V10_UG_C_web


iv

Table of Contents


FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Saety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Industry Canada Radiation Exposure Statement:. . . . . . . . . . . . . . . . . . . . . . .36

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Avis d’Industrie Canada concernant l’exposition aux radioréquences :. . . . . . . . .36

User Inormation or Consumer Products Covered by EU Directive 2002/96/EC on WasteElectric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Appendix F: Contact Inormation 41

8/8/2019 WAP200E_V10_UG_C_web


1

Introduction


Chapter 1

Chapter 1:Introduction

Thank you or choosing the Wireless-G Exterior AccessPoint with Power Over Ethernet.

The Linksys Wireless-G Exterior Access Point with PowerOver Ethernet lets you connect Wireless-G (802.11g) orWireless-B (802.11b) devices to your wired network so youcan add PCs to the network with no cabling hassle. Thisweather-proo Access Point creates a “wireless bubble” inexterior spaces, like patios, pool areas, and outdoor caés.Power over Ethernet support makes it easy to install, andyou can create multiple SSIDs that connect to individualVLANs to keep your traic separated.

It’s also perect or use as a bridge, a kind o “cable-less

cable” to connect remote areas together. Maybe yourwarehouse is in a separate building rom your oices. Ormaybe you need to connect the separate buildings o acollege campus. With one Wireless-G Exterior Access Pointon each building, you’re connected with no cable to run.The exterior-rated case protects the access point, andcontains an internal antenna.

To protect your data and privacy, the Wireless-G ExteriorAccess Point with Power Over Ethernet supports bothWired Equivalent Privacy (WEP) and the industrial-strengthwireless security o Wi-Fi Protected Access™ (WPA),encoding all your wireless transmissions with powerul

encryption. The MAC Address ilter lets you decide exactlywho has access to your wireless network, and advancedlogging keeps you appraised. Coniguration is a snap withthe web browser-based coniguration utility.

The Linksys Wireless-G Exterior Access Point with PowerOver Ethernet is the best way to add wireless access to theoutdoor areas o your home or business.

8/8/2019 WAP200E_V10_UG_C_web


2

Planning Your Wireless Network


Chapter 2

Chapter 2:Planning Your Wireless

Network Network Topology

A wireless network is a group o computers, each equippedwith one or more wireless adapters. Computers in awireless network must be conigured to share the sameradio channel to talk to each other. Several PCs equippedwith wireless cards or adapters can communicate witheach other to orm an ad-hoc network without the use o an access point.

Linksys wireless adapters also provide access to a wired

network when using an access point or wireless router.An integrated wireless and wired network is called aninrastructure network. Each wireless PC in an inrastructurenetwork can talk to any computer in a wired or wirelessnetwork via the access point or wireless router.

An inrastructure coniguration extends the accessibilityo a wireless PC to a wired network, and may double theeective wireless transmission range or two wirelessadapter PCs. Since an access point is able to orward datawithin a network, the eective transmission range in aninrastructure network may be doubled (depending onantenna characteristics).

Roaming

Inrastructure mode also supports roaming capabilitiesor mobile users. Roaming means that you can move yourwireless PC within your network and the access pointswill pick up the wireless PC’s signal, providing that theyboth share the same wireless channel, SSID, and wirelesssecurity settings.

Beore you consider roaming, choose a easible radiochannel and optimum access point position. Proper accesspoint positioning combined with a clear radio signal willgreatly enhance perormance.

NOTE: Spanning Tree Protocol should bedisabled on the switches connecting to the APsto allow roaming to work without disruption.

Network Layout

The Access Point has been designed or use with 802.11gand 802.11b products, such as the Notebook Adaptersor your laptop computers, PCI Adapters or your desktopPCs, and USB Adapters.

These wireless products can also communicate with a802.11g or 802.11b Wireless PrintServer.

To link your wired network with your wireless network,connect the Access Point’s Ethernet network port to any

switch or router with Power over Ethernet (PoE)—or a PoEinjector, such as the Linksys WAPPOE or WAPPOE12.

NOTE: 12 VDC on WAPPOE12 is or the splitteroutput. Both PoE Injectors provide 48 VDCpower output.

Go to the Linksys website at www.linksys.com or moreinormation about wireless products.

Example o a Simple Wireless Network

Example o Simple Wireless Network

The above diagram shows a typical inrastructurewireless network setup. The Wireless Access Points areconnecting to a Linksys switch that provides power tothe Access Points. Each Access Point can connect multiplewireless devices to the network. This network will provideconnectivity among wireless network devices and PCsthat have a wired connection to the switch.

The switch then can connect to a router that can connectto an ISP or Internet access.

8/8/2019 WAP200E_V10_UG_C_web


3

Product Overview


Chapter 3

Chapter 3:Product Overview

Front PanelThe Access Point’s LEDs, where inormation about network activity is displayed, are located on the ront panel.

Front Panel

Power (Green) The Power LED lights up whenthe Access Point is powered on.

Wired (Green) The Wired LED lights up whenthe Access Point is successully connected to adevice through the Ethernet network port. I the

Wired LED is lashing, the Access Point is activelysending to or receiving data rom one o thedevices over the Ethernet network port.

Wireless (Green) The Wireless LED lights upwhen the wireless module is active on the AccessPoint. I the Wireless LED is lashing, the AccessPoint is actively sending to or receiving data roma wireless device.

Bottom Panel

The Ethernet network port is located on the bottom panelo the Access Point.

Bottom Panel

Ethernet network port The Ethernet network port connects to Ethernet network devices, suchas a switch or router. The Access Point is poweredusing Power Over Ethernet. I the switch or routerdoesn’t support Power Over Ethernet, then aPower Over Ethernet Injector must be installed.

Top Panel

The antenna port is located on the top panel o the AccessPoint.

Top Panel

Antenna Port The Access Point has built-in,1x2 MIMO 9dBi directional antennas. It also hasa reverse polarity emale N-type antenna portor an optional, high-gain external antennasuch as the HGA9N. One o the two internalantennas will be disabled automatically whenan external antenna is connected.

8/8/2019 WAP200E_V10_UG_C_web


4

Product Overview


Chapter 3

Back Panel

The Access Point’s Reset button and ground are locatedon the back panel.

Reset button

Ground

Back Panel

Reset Button There are two ways to Reset the AccessPoint’s actory deaults. Either press the Reset button, orapproximately ten seconds, or restore the deaults usingthe Access Point’s web-based utility.

IMPORTANT: Resetting the Access Point willerase all o your settings (including wirelesssecurity, IP address, and power output) andreplace them with the actory deaults. Do notreset the Access Point i you want to retain thesesettings.

Ground Beore you mount the Access Point, you mustground the Access Point (to a large piece o metal) as aprecaution against electric shock.

The Antenna Pattern

The Wireless-G Exterior Access Point uses 1X2 MIMO (1Tx,2Rx) so it has two built-in antennas. The right antenna isthe main antenna or Tx traic. When an external antenna

is attached, the right antenna is disabled and the externalantenna is used or Tx traic. Currently, only the HGA9N(9dBi omni-directional antenna) is compatible with theWireless-G Exterior Access Point.

Right Antenna Pattern

3dB BW: 50 degree, peak gain: 6.3 dBi

Let Antenna Pattern

3dB BW: 63 degree, peak gain: 4.9 dBi

8/8/2019 WAP200E_V10_UG_C_web


5

Product Overview


Chapter 3

Radio Coverage o the Access Point to Client Devices

When using the Access Point to connect client devices,adjust it so the client devices are on the same horizontalplane as the Access Point and within a 3dB angle o 50 degrees. This will ensure the strongest signal and

maximum reach.

I the Access Point is used inside a building, put it in acorner o the building or maximum coverage.

Access Point to Access Point (bridging) Radio Coverage

I the Access Point is used as a bridge or repeater, adjustthe Access Points so they ace each other, this will ensure

the strongest signal and maximum reach.

Make sure that the orientation o the two DirectionalAntennas is the same. The radio wave is polarized so a 90degree rotation will result in no received power.

Due to its directional characteristics, the internal antennais ideal or point-to-point bridge mode or the spokeside o point-to-multipoint bridge mode. An externalomni-directional antenna (e.g. HGA9N) is recommendedor repeater mode applications.

8/8/2019 WAP200E_V10_UG_C_web


6

Installation


Chapter 4

Chapter 4:Installation

OverviewThis chapter explains how to mount and connect theAccess Point.

Depending on your application, you might want to setup the IP address o the device irst beore mountingthe device. Reer to “Chapter 5: Quick ConigurationOverview”.

Personal Installation

This product should be installed by a qualiied installationproessional with RF and related rule knowledge. Generalusers should not attempt to install this product or modiythe settings.

Installation Location

The product should be installed in a location where theradiating antenna is at least 20 cm rom anyone undernormal operating conditions. This is required to meetregulatory RF exposure requirements.

External Antenna

Use only antennas approved by Linksys. Antennas that have

not been approved by Linksys may produce unwantedspurious or excessive RF transmitting power, this may leadto violation o FCC limitations and is prohibited.

Installation Procedure

Follow the Hardware Installation instructions or detailson installing this product.

WARNING: Please careully select theinstallation position and make sure that theinal output power does not exceed the limitdeined in US Rule CFR 47 Part 15, section

15.247 and 15.407. Violation o the rule couldlead to serious ederal penalties.

Hardware InstallationLocate an optimum location on a wall or the Access1.Point. Reer to the antenna pattern in “Chapter 3:Product Overview” to adjust the angle o the AccessPoint or your application.

Using the mounting plate as a template, mark the2.locations o the two wall-mount slots that are on thebottom o the mounting plate. Then, install a screwinto each location.

Mark the Locations o the Two Wall-Mount Slots

Use our screws (included with the Access Point) to3.attach the mounting plate to the back panel o theAccess Point.

Attach the Mounting Plate

Connect the included Category 5e Ethernet network 4.cable to the Ethernet network port o the Access Point.

8/8/2019 WAP200E_V10_UG_C_web


7

Installation


Chapter 4

Then, screw the connector cap tightly onto the port, sothe Access Point has a water-resistant seal.

I you want to connect an optional, high-gain external5.antenna, remove the cap that protects the antenna

port, then, connect your antenna cable to this port.Make sure that you properly ground the Access Point.6.

Ground the Access Point

Line up the Access Point’s wall-mount slots with the7.two screws on the wall. Then, slide the Access Pointdown so that the screws it snugly in the slots.

Attach a screw (not included) in each o the two holes8.on the top o the mounting plate so that the AccessPoint is securely mounted to the wall.

Attach the Access Point to the Wall

Connect the other end o the Ethernet network cable9.to a switch, router, or other device that supports Powerover Ethernet. The Access Point will then be connectedto your wired network.

Now that the hardware installation is complete, proceed to“Chapter 5: Quick Coniguration Overview” or directionson how to conigure the Access Point.

8/8/2019 WAP200E_V10_UG_C_web


8

Quick Configuration Overview


Chapter 5

Chapter 5:Quick Coniguration

OverviewOverview

The Access Point has been designed to be unctional rightout o the box with the deault settings. However, i you’dlike to change these settings, the Access Point can beconigured through your web browser with the web-basedutility. This chapter explains how to use the utility.

The utility can be accessed via web browsers, such asMicrosot Internet Explorer or Mozilla Fireox throughthe use o a computer that is networked with the Access

Point.For a basic network setup, most users only have to use theollowing screens o the Utility:

Setup• On the Setup screen, enter your basic network settings (IP address) here.

Management• Click the Administration tab and thenselect the Management screen. The Access Point’sdeault password is admin. To secure the Access Point,change the AP Password rom its deault.

Most users will also customize their wireless settings:

Wireless• On the Wireless screen, change deault SSIDunder the Basic Wireless Settings tab. Select the level o security under the Wireless Security tab.

Accessing the Web-Based Utility

There are two ways to power your Access Point.

48V Power Injector (e.g. Linksys WAPPOE)• Powerup your Access Point irst then connect the cable onyour Injector to your PC.

PoE switch (e.g. Linksys SRW224P)• Connect yourAccess Point and your PC to the same LAN.

To access the web-based utility, perorm the ollowingsteps:

Conigure your PC with a static IP address in the1.same subnet as the Access Point’s deault IP address(192.168.1.245). I there is DHCP server connectedto the switch, conigure it to assign the IP address in192.168.1.0/24 subnet. Your PC will get an IP addressin the subnet through the DHCP.

Launch your web browser, such as Internet Explorer or2.Mozilla Fireox and enter the Access Point’s deault IPaddress, 192.168.1.245, in the Address ield. Press theEnter key.

Enter3. admin in the User Name ield. The irst timeyou open the Web-based Utility, use the deaultpassword, admin. (You can set a new password rom Administration > Management ) Then click the OK button.

Ater setting up the Access Point to use DHCP or manuallyconigure a new IP address, move your Access Point to thedesired network. You will have to use the new IP addressthe next time you access the Web-based Utility.

Navigating the Web-Based Utility

The web-based utility consists o the ollowing ive main

tabs: Setup, Wireless, AP Mode, Administration, andStatus. Additional screens (sub tabs) will be availablerom most o the main tabs.

The ollowing briely describes the main and sub tabs o the Utility.

Setup

Basic Setup Enter the Host Name and IP Address settingson this screen.

Time You can set the time either manually or automaticallyrom a time server i the Access Point can access the public

Internet.

Wireless

You will use the Wireless tabs to enter a variety o wirelesssettings or the Access Point.

Basic Wireless Settings Choose the wireless network mode (e.g. wireless-G), wireless channel, and SSIDconiguration on this screen.

Wireless Security Use this screen to conigure the AccessPoint’s security settings including access authentication,data encryption, and wireless isolation.

Wireless Connection Control Use this screen to populateyour Access List to permit or block certain MAC addressaccess to your wireless network.

Advanced Wireless Settings Use this screen to conigurethe Access Point’s more advanced wireless settings suchas Beacon interval, Output Power, etc.

VLAN & QoS Use this screen to conigure the VLAN andQoS related settings or the Access Point.

8/8/2019 WAP200E_V10_UG_C_web


9

Quick Configuration Overview


Chapter 5

AP Mode

Use this screen to conigure the Access Point operationmode with WDS (Wireless Distribution System).

AdministrationYou will use the Administration tabs to manage the AccessPoint.

Management This screen allows you to customize thepassword and Simple Network Management Protocol(SNMP) settings.

Log Conigure the Log settings or the Access Point onthis screen.

Factory Deault Use this screen to reset the Access Pointto its actory deault settings.

Firmware Upgrade Upgrade the Access Point’s irmwareon this screen.

Reboot Use this screen to reboot the Access Point.

Conig Management You can back up the conigurationile or the Access Point, as well as save the backupconiguration ile to the Access Point.

Status

You will be able to view status inormation or your localnetwork, wireless networks, and network perormance.

Local Network This screen displays system inormation,

including sotware & hardware version, MAC address, andIP address on the LAN side o the Access Point.

Wireless This screen displays wireless network settingsincluding SSID, network mode, and wireless channel.

System Perormance This screen displays the currenttraic statistics o the Access Point’s Wireless and LANports.

8/8/2019 WAP200E_V10_UG_C_web


Chapter 6 Advanced Configuration

10Wireless-G Exterior Access Point with Power Over Ethernet

Chapter 6:Advanced Coniguration

Open your web browser and enter http://192.168.1.245into the Address ield. Press the Enter key and the Password screen will appear.

Address Bar

NOTE: The deault IP address is 192.168.1.245.I the IP address has been changed using DHCPor via the console interace, enter the assignedIP address instead o the deault.

The irst time you open the web-based utility, enteradmin (the deault username) in the User name ield andenter it again in the Password ield. Click the OK button.You can change the Access Point’s password later rom the Administration > Management screen.

Login Screen

Web-Based Utility

The irst screen that appears in the web-based utility is theSetup screen. This allows you to change the Access Point’sgeneral settings. There are ive tabs across the top o the screen: Setup, Wireless, AP Mode, Administration,and Status. Each tab contains screens that will help youconigure and manage the Access Point.

Setup > Basic Setup

Setup > Basic Setup

Enter names or the Access Point. The host name can beused to access the Web Utility through the network i DNShas been set up. The device name is or the beneit o identiying your Access Point ater you log in.

Setup

Host Name This is the host name assigned to the AccessPoint. This host name will be published to your DNS serveri the Access Point is conigured to acquire the IP addressthrough DHCP. In that case, Linksys recommends to ollowthe company policy on the host name assignment. The

deault name is Linksys.Device Name You may assign any device name tothe Access Point. This name is only used by the AccessPoint administrator or identiication purposes. Unique,memorable names are helpul, especially i you areemploying multiple access points on the same network.The deault name is WAP200E.

Network Setup

The selections under this heading allow you to conigurethe Access Point’s IP address setting(s).

IP Settings

Static IP Address Selected by deault, this option is usedto assign a static or ixed IP address to the Access Point.

Local IP Address• The IP address must be unique to yournetwork. The deault IP address is 192.168.1.245.

Subnet Mask • The Subnet Mask must be the same asthat set on the LAN that your Access Point is connectedto. The deault is 255.255.255.0.

Deault Gateway• Enter the Deault Gateway Address,typically this is the IP address o your router.

8/8/2019 WAP200E_V10_UG_C_web




Primary DNS (Required) and Secondary DNS•

(Optional) Your ISP will provide you with at least oneDNS (Domain Name System) Server IP Address.

Automatic Coniguration - DHCP I you have a DHCP

server enabled on the LAN and want it to assign an IPaddress to the Access Point, the select this option.

Change these settings as described here and click SaveSettings to apply your changes, or click Cancel Changes to cancel your changes. Help inormation is available onthe right side o the screen.

Setup > Time

This allows you to change the Access Point’s time settings.The correct time setting can help the administrator tosearch the system log to identiy problems.

Setup > Time

Time

You can set the time either manually or automaticallyrom a time server i the Access Point can access the publicInternet. The deault is to set the time Automatically.

Manually Select this option to set the date and timemanually.

Automatically Select this option and time zone. TheAccess Point will contact the public time server to get thecurrent time.

Automatically adjust clock or daylight saving•

changes Select this option i you are in using theAccess Point in a location that observes daylight savingtime.

User Deined NTP Server• Enable this option i youhave set up local NTP server. Deault is Disabled.

NTP Server IP• Enter the IP address o user deinedNTP Server.

Change these settings as described here and click SaveSettings to apply your changes, or click Cancel Changes

to cancel your changes. Help inormation is available onthe right side o the screen.

Wireless > Basic Wireless Settings

Change the basic wireless network settings on this screen.The Access Point can connect to up to our wirelessnetworks (SSIDs) at the same time, so this screen oerssettings or up to our dierent SSIDs. Each SSID owns itsown MAC address on this Access Point.

Wireless > Basic Wireless Settings

Basic Settings

Conigure the Wireless Network basic attributes or the

entire system and or each SSID.Wireless Network Mode Select one o the ollowingmodes. The deault is Mixed.

Disable• To disable wireless connectivity completely.This might be useul during system maintenance.

B-Only• All the wireless client devices can beconnected to the Access Point at Wireless-B data rateswith maximum speed at 11Mbps.

G-Only• Wireless-G client devices can be connected atWireless-G data rates with maximum speed at 54Mbps.Wireless-B clients cannot be connected in this mode.

Mixed• Both Wireless-B and Wireless-G client devicescan be connected at their respective data rates.Wireless-G devices can be connected at Wireless-Gdata rates.

Wireless Channel Select the appropriate channel to beused among your Access Point and your client devices.When Auto is selected, your Access Point will select thechannel with the lowest amount o wireless intererencewhile the system is powering up. Auto channel selectionwill start when you click Save Settings button, it will takeseveral seconds to scan through all the channels to indthe best channel. The deault setting is Auto.

8/8/2019 WAP200E_V10_UG_C_web




SSID Name The SSID is the unique name shared amongall devices in a wireless network. It is case-sensitive, mustnot exceed 32 alphanumeric characters, and may be anykeyboard character. Make sure this setting is the sameor all devices in your wireless network. The deault SSID

name is linksys-g.

SSID Broadcast This option allows the SSID to bebroadcast on your network. You may want to enablethis unction while coniguring your network, but makesure that you disable it when you are inished. Withthis enabled, someone could easily obtain the SSIDinormation with site survey sotware or Windows XP andgain unauthorized access to your network. Click Enabledto broadcast the SSID to all wireless devices in range.Click Disabled to increase network security and preventthe SSID rom being seen on networked PCs. The deaultis Enabled in order to help users conigure their network

beore use.Change these settings as described here and click SaveSettings to apply your changes, or click Cancel Changes to cancel your changes. Help inormation is available onthe right side o the screen.

Wireless > Wireless Security

Change the Access Point’s wireless security settings onthis screen.

Wireless > Wireless Security

Wireless Security

Select SSID Select any o the SSID names conigured onthe Basic Wireless Settings tab.

Wireless Isolation (between SSID) Wireless Isolationprevents eavesdropping in the network. When it isEnabled, wireless rames received on this Access Point willnot be orwarded to other wireless networks (SSIDs). Forexample, i you have a wireless hotspot, you may want to

keep the wireless network (SSID) isolated rom your otherwireless networks (SSIDs). This is a global option applyingto all SSIDs. The deault is Enabled.

The ollowing options are speciic or each SSID:

Security Mode Select the wireless security mode youwant to use: WPA-Personal, WPA2-Personal, WPA2-PersonalMixed, WPA-Enterprise, WPA2-Enterprise, WPA2-EnterpriseMixed, RADIUS, or WEP. (WPA stands or Wi-Fi ProtectedAccess, which is a security standard stronger than WEPencryption and orward compatible with IEEE 802.11i. WEPstands or Wired Equivalent Privacy, Enterprise modes usea RADIUS server or authentication, while RADIUS stands

or Remote Authentication Dial-In User Service.) Reer tothe appropriate instructions below ater you select theAuthentication Type and SSID Interoperability settings.For detailed instructions on coniguring wireless securityor the Access Point, reer to “Appendix B: Wireless SecurityChecklist”. To disable wireless security completely, selectDisabled. The deault is Disabled.

Wireless Isolation (within SSID) When disabled, wirelessPCs that are associated to the same network name (SSID),can see and transer iles between each other. By enablingthis eature, Wireless PCs will not be able to see each other.This eature is very useul when setting up a wireless

hotspot location. The deault is Disabled.Following section describes the detailed options or eachSecurity Mode.

WPA-Personal (aka WPA-PSK)

Wireless > Wireless Security > WPA-Personal

Encryption WPA oers you two encryption methods, TKIPand AES or data encryption. Select the type o algorithmyou want to use, TKIP or AES. The deault is TKIP.

Shared Secret Enter a shared secret o 8-63 characters.

8/8/2019 WAP200E_V10_UG_C_web




Key Renewal Timeout Enter a Key Renewal Timeoutperiod, which instructs the Access Point how oten itshould change the encryption keys. The deault is 3600 seconds.

WPA2-Personal

Wireless > Wireless Security > WPA2-Personal

Encryption WPA2 always uses AES or data encryption.



WPA2-Personal Mixed

This security mode supports the transition romWPA-Personal to WPA2-Personal. You can have clientdevices that use either WPA-Personal or WPA2-Personal.The Access Point will automatically choose the encryptionalgorithm used by each client device.

Wireless > Wireless Security > WPA2=Personal Mixed

Encryption Mixed Mode automatically chooses TKIP orAES or data encryption.



WPA-EnterpriseThis option eatures WPA used in coordination with aRADIUS server or client authentication. (This should onlybe used when a RADIUS server is connected to the AccessPoint.)

Wireless > Wireless Security > WPA-Enterprise

RADIUS Server IP Address Enter the RADIUS server’s IPaddress.

RADIUS Server Port Enter the port number used by the

RADIUS server. The deault is 1812.Encryption WPA oers you two encryption methods, TKIPand AES or data encryption. Select the type o algorithmyou want to use, TKIP or AES. The deault is TKIP.

Shared Secret Enter the Shared Secret key used by theAccess Point and RADIUS server.


WPA2-Enterprise

This option eatures WPA2 used in coordination with aRADIUS server or client authentication. (This should onlybe used when a RADIUS server is connected to the AccessPoint.)

8/8/2019 WAP200E_V10_UG_C_web




Wireless > Wireless Security > WPA2-Enterprise


RADIUS Server Port Enter the port number used by theRADIUS server. The deault is 1812.

Encryption WPA2 always uses AES or data encryption.


Key Renewal Timeout Enter a Key Renewal Timeoutperiod, which instructs the Access Point how oten itshould change the encryption keys. The deault is 3600seconds.

WPA2-Enterprise Mixed

This security mode supports the transition rom WPA-Enterprise to WPA2-Enterprise. You can have client devicesthat use either WPA-Enterprise or WPA2-Enterprise. TheAccess Point will automatically choose the encryptionalgorithm used by each client device.

Wireless > Wireless Security > WPA2-Enterprise Mixed



Encryption Mixed Mode automatically chooses TKIP orAES or data encryption.


Key Renewal Timeout Enter a Key Renewal Timeoutperiod, which instructs the Access Point how oten itshould change the encryption keys. The deault is 3600seconds.

RADIUS

This security mode is also known as Dynamic WEP with IEEE802.1X. A RADIUS server is used or client authenticationand WEP is used or data encryption. The WEP key isautomatically generated by the RADIUS server. Manual

WEP key is no longer supported to ensure compatibilitywith Microsot’s Windows implementation.

Wireless > Wireless Security > RADIUS




WEP

This security mode is deined in the original IEEE 802.11.This mode is not recommended now due to its weak security protection. Users are urged to migrate to WPA orWPA2.

8/8/2019 WAP200E_V10_UG_C_web




Wireless > Wireless Security > WEP

Authentication Type Choose the 802.11 authenticationtype as either Open System or Shared Key. The deault isOpen System.

Deault Transmit Key Select the key to be used or dataencryption.

Encryption Select a level o WEP encryption, 64 bits (10hex digits) or 128 bits (26 hex digits).

Passphrase I you want to generate WEP keys using a

Passphrase, then enter the Passphrase in the ield providedand click the Generate key. Those auto-generated keys arenot as strong as manual WEP keys.

Key 1-4 I you want to manually enter WEP keys, thencomplete the ields provided. Each WEP key can consist o the letters “A” through “F” and the numbers “0” through “9”.It should be 10 characters in length or 64-bit encryptionor 26 characters in length or 128-bit encryption.

Change these settings as described here and click SaveSettings to apply your changes, or click Cancel Changesto cancel your changes. Help inormation is available onthe right side o the screen.

Disable

There is no option to be conigured or this mode.

When you have inished making changes to the screen,click the Save Settings button to save the changes, or click the Cancel Changes button to undo your changes. Helpinormation is available on the right side o the screen.

Wireless > Wireless Connection Control

This screen allows you to conigure the Connection ControlList to either permit or block speciic wireless client devicesconnecting to (associating with) the Access Point.

Wireless > Wireless Connection Control

Wireless Connection Control

Select SSID Select the SSID o the wireless network thatyou want to use wireless connection control on.

Enabled/Disabled Enable or disable wireless connectioncontrol. The deault is disabled.

Connection Control

Allow only ollowing MAC addresses to connect towireless network When this option is selected, onlydevices with a MAC address speciied in the ConnectionControl List can connect to the Access Point.

Prevent ollowing MAC addresses rom connecting towireless network When this option is selected, deviceswith a MAC address speciied in the Connection ControlList will not be allowed to connect to the Access Point.

Wireless Client List

Instead o manually entering the MAC addresses o eachclient, the Access Point provides a convenient way toselect a speciic client device rom the client associationtable. Click this button and a window appears to let youselect a MAC address rom the table. The selected MACaddress will be entered into the Connection Control List.

8/8/2019 WAP200E_V10_UG_C_web




Connection Control List

MAC 01-16 Enter the MAC addresses o the wireless clientdevices you want to control.


Wireless > Advanced Wireless Settings

This screen allows you to conigure the advanced settingsor the Access Point. Linksys recommends to let yourAccess Point automatically adjust the parameters ormaximum data throughput.

Wireless > Advanced Wireless Settings

Advanced Settings

CTS Protection Mode CTS (Clear-To-Send) ProtectionMode unction boosts the Access Point’s ability to catchall wireless transmissions, but will severely decreaseperormance. Keep the deault setting, Auto, so the AccessPoint can use this eature as needed, when the Wireless-Gproducts are not able to transmit to the Access Point in anenvironment with heavy 802.11b traic. Select Disabled i you want to permanently disable this eature.

BSSBasicRateSet This setting is a series o rates thatare advertised to other wireless devices as deined inIEEE 802.11 speciications, so they know which data ratesthe Access Point can support. One o the rates is pickedrom the list or transmitting control rames, broadcast/multicast rames, or ACK rames. To support both 802.11b& 802.11g devices, use the Deault (Mixed mode) settingso that rames can be decoded by all devices. To support802.11g devices only, use the All (G-only mode) settingto achieve higher rame rates. For regular data rames,the transmission rate is conigured through the Tx RateLimiting on the Wireless > VLAN & QoS tab.

Power Output You can adjust the output power o theAccess Point to get the appropriate coverage or yourwireless network. Select the level you need or yourenvironment. I you are not sure o which setting tochoose, then keep the deault setting, 100%.

Beacon Interval This value indicates the requencyinterval o the beacon. A beacon is a packet broadcastby the Access Point to keep the network synchronized. Abeacon includes the wireless networks service area, theAccess Point address, the Broadcast destination addresses,a time stamp, Delivery Traic Indicator Maps, and theTraic Indicator Message (TIM). The deault is 100 ms.

DTIM Interval This value indicates how oten the AccessPoint sends out a Delivery Traic Indication Message(DTIM). Lower settings result in more eicient networking,while preventing your PC rom dropping into power-saving sleep mode. Higher settings allow your PC to

enter sleep mode, thus saving power, but intereres withwireless transmissions. The deault is 1 ms.

RTS Threshold This setting determines how large a packetcan be beore the Access Point coordinates transmissionand reception to ensure eicient communication. Thisvalue should remain at its deault setting o 2347. I youencounter inconsistent data low, only minor modiicationsare recommended.

Fragmentation Threshold This speciies the maximumsize a data packet can be beore splitting and creating anew packet. It should remain at its deault setting o 2346.A smaller setting means smaller packets, which will createmore packets or each transmission. I you experiencehigh packet error rates, you can decrease this value, butit will likely decrease overall network perormance. Onlyminor modiications o this value are recommended.


8/8/2019 WAP200E_V10_UG_C_web




Wireless > VLAN & QoS

This screen allows you to conigure the VLAN and QoSrelated settings or the Access Point.

Wireless > VLAN & QoS

VLAN

The ollowing options are global VLAN settings or theAccess Point.

VLAN Select Enabled i you want to pass 802.1q VLANtagged traic between the wired LAN and wireless LAN.Your Access Point will map the VLAN tag (wired side) to

dierent SSIDs (wireless side) according to your speciiedsettings. Select Disabled and your Access Point will drop alltagged traic coming in rom the wired LAN. The deaultis Disabled.

Deault VLAN ID Enter the deault VLAN ID number (1- 4094), the deault value is 1. The deault VLAN numbershould match with your Switch’s settings. For example,the SRW2024 has Trunk port mode which set deault VLAN(PVID) to 1 untagged, while General port mode can setPVID to any VLAN either tagged or untagged.

VLAN Tag Set the tagging option or the deault VLANID. This has to match your Switch’s settings. The deault is

untagged.AP Management VLAN When the VLAN option isenabled, the value entered (VLAN ID) in this ield deinesthe VLAN that connects to the Access Point. The deaultvalue is 1. The VLAN should be accessible rom the wiredside in order to use web-based utility. To access theweb-based utility rom wireless side, the SSID needs tomap to the same VLAN ID. Remember to enable wirelessweb access on the Administration > Management tab.

QoS

The ollowing options are VLAN global settings or theAccess Point.

Deault CoS (Priority) Select Enabled i you want toassign a deault CoS value to each SSID. This option isautomatically enabled when the VLAN option is enabled.The deault is Disabled.

U-APSD (Unscheduled Automatic Power SaveDelivery) This option is only available when WMM isenabled on any o the SSIDs. Select Enabled i you wantclient devices with U-APSD capability to take advantageo the power save mode. The deault is Disabled.

SSID Name Displays the SSIDs deined under the BasicWireless Settings tab. I an SSID has been disabled, theoptions cannot be conigured.

VLAN ID Select a VLAN ID (1 - 4094) or the SSID whereyou want to map the traic to on the wired side. Thewireless traic will not carry VLAN inormation. MultipleSSIDs can map to the same VLAN on the wired side.

Priority You can assign the deault priority (802.1p COSbits) or packets coming in rom each wireless network by selecting a number rom the drop-down menu. Thehigher the number, the higher the priority will be. Thedeault is 0.

Tx Rate Limitation You can limit the maximum datarate used in your network to save bandwidth and powerconsumption on client devices. The actual data rate is

determined by the Auto-Fallback mechanism betweenyour Access Point and a client device. The deault is 54Mbps or Mixed or G-Only wireless mode, 11 Mbps or B-Only mode.

WMM Wi-Fi Multimedia is a QoS eature deined by theWiFi Alliance beore IEEE 802.11e was inalized. Now it ispart o IEEE 802.11e. When this is enabled, it provides ourpriority queues or dierent types o traic. It automaticallymaps the incoming packets to the appropriate queuesbased on QoS settings (in the IP or layer 2 header). WMMprovides the capability to prioritize wireless traic in yourenvironment. The deault is Disabled (unchecked).

8/8/2019 WAP200E_V10_UG_C_web




AP Mode

On this screen you can change the Access Point’s mode o operation. In most cases, you can keep the deault setting- Access Point. You may wish to change the Access Point’s

mode o operation i you want to use the Access Point asa wireless repeater to extend the range o your wirelessnetwork. You may also wish to change the Access Point’smode o operation i you want to use the Access Point asa wireless bridge; or example, you can use two AccessPoints in Wireless Bridge mode to connect two wirednetworks that are in two dierent buildings.

AP Mode

The Access Point oers three modes o operation: AccessPoint, Wireless Repeater, and Wireless Bridge. For theRepeater and Bridge modes, make sure the SSID, channel,and security settings are the same or the other wirelessaccess points/devices.

MAC Address

The MAC address o the Access Point is displayed here.

Access Point The Mode is set to Access Point by deault.This connects your wireless PCs to a wired network. Inmost cases, no change is necessary.

Allow wireless signal to be repeated by a•

repeater Select this option i you want to use anotherwireless device to repeat the signal o this Access Point.You will need to enter the MAC address(es) o therepeating device(s). Up to 3 repeaters can be used.

Wireless Repeater When set to Wireless Repeater mode,the Wireless Repeater is able to talk to up a remote accesspoint within its range and retransmit its signal. Click SiteSurvey to select the access point that will have its signalrepeated by this Access Point or enter the MAC address o

the access point manually.

Access Point- WirelessRepeater

Mode

Access Point

Desktop

Desktop

Laptop

Laptop

Internet

Modem

Switch

Wired LAN

Wireless Repeater Mode

8/8/2019 WAP200E_V10_UG_C_web




Wireless Bridge This mode connects physically separatedwired networks using multiple access points. Wirelessclients will not be able to connect to the access point inthis mode. Enter the MAC address(es) o the access point(s)that will bridge to this access point.

Switch Switch

SwitchSwitch

Access Point

- WirelessBridge Mode

Access Point


Access Point- Wireless

Bridge Mode

Access Point


Access Point


Wired LANWired LAN

Wired LANWired LAN

Wireless Bridge Mode

Administration > Management

On this screen you can conigure the password, WebAccess, and SNMP settings.

Administration > Management

AP Password

You should change the username/password that controlsaccess to the Access Point’s web-based utility.

Local AP PasswordUser Name Modiy the administrator username. Thedeault is admin.

AP Password Modiy the administrator password or theAccess Point’s web-based utility. The deault is admin.

Re-enter to conirm To conirm the new Password, enterit again in this ield.

Web Access

To increase the security on accessing web-based utility.You can enable HTTPS. Once enabled, users need to use

https:// when accessing the web-based utility.Web HTTPS Access Use secured HTTP session to accessWeb based Utility. The deault is Disabled.

Wireless Web Access Allow or deny wireless clients toaccess Web based Utility. The deault is Enabled.

SNMP

SNMP is a popular network monitoring and managementprotocol. It provides network administrators with theability to monitor the status o the Access Point and

8/8/2019 WAP200E_V10_UG_C_web




receive notiication o any critical events as they occur onthe Access Point.

To enable the SNMP support eature, select Enabled.Otherwise, select Disabled. The deault is Disabled.

Identification

Contact Enter the name o the contact person, such as anetwork administrator, or the Access Point.

Device Name Enter the name you wish to give to theAccess Point.

Location Enter the location o the Access Point.

Get Community Enter the password that allows read-only access to the Access Point’s SNMP inormation.

Set Community Enter the password that allows read/write access to the Access Point’s SNMP inormation.

SNMP Trap-Community Enter the password required bythe remote host computer that will receive trap messagesor notices sent by the Access Point.

SNMP Trusted Host You can restrict access to the AccessPoint’s SNMP inormation by IP address. Enter the IPaddress in the ield provided. I this ield is let blank, thenaccess is permitted rom any IP address.

SNMP Trap-Destination Enter the IP address o the remote host computer that will receive the trapmessages.

Change these settings as described here and click Save

Settings to apply your changes, or click Cancel Changes to cancel your changes. Help inormation is displayedon the right-hand side o the screen, and click Help oradditional details.

Administration > Log

On this screen you can conigure the log settings andalerts o particular events.

Administration > Log

Log

You can have logs that keep track o the Access Point’sactivities.

Email AlertE-Mail Alert I you want the Access Point to send e-mailalerts in the event o certain activities, select Enabled. Thedeault is Disabled.

E-Mail Address or Logs Enter the e-mail address thatwill receive logs.

Notification Queue Length

Log Queue Length You can designate the length o thelog that will be e-mailed to you. The deault is 20 entries.

Log Time Threshold You can designate how oten the

log will be emailed to you. The deault is 600 seconds (10minutes).

Syslog Notification

Syslog is a standard protocol used to capture inormationabout network activity. The Access Point supports thisprotocol and sends its activity logs to an external server. Toenable Syslog, select Enabled. The deault is Disabled.

Syslog Server IP Address Enter the IP address o theSyslog server. In addition to the standard event log, theAccess Point can send a detailed log to an external Syslogserver. The Access Point’s Syslog captures all log activities

and includes this inormation about all data transmissions:every connection source and destination IP address, IPserver, and number o bytes transerred.

Log

Select the events that you want the Access Point to keepa log.

Unauthorized Login Attempt I you want to receivealert logs about any unauthorized login attempts, click the checkbox.

Authorized Login I you want to log authorized logins,

click the checkbox.System Error Messages I you want to log system errormessages, click the checkbox.

Coniguration Changes I you want to log anyconiguration changes, click the checkbox.


8/8/2019 WAP200E_V10_UG_C_web




Administration > Factory Deault

On this screen you can restore the Access Point’s actorydeault settings.

Administration > Factory Deault

Factory Deault

Note any custom settings beore you restore the actorydeaults. Once the Access Point is reset, you will have tore-enter all o your coniguration settings.

Restore Factory Deaults To restore the Access Point’sactory deault settings, click the Yes radio button. Then,click Save Settings. Your Access Point will reboot and

come back up with the actory deault settings in a ewseconds.

Click Save Settings to apply your change, or click CancelChanges to cancel your change. Help inormation isavailable on the right side o the screen.

Administration > Firmware Upgrade

On this screen you can upgrade the Access Point’s irmware.Do not upgrade the irmware unless you are experiencingproblems with the Access Point or the new irmware has aeature you want to use.

Administration > Firmware Upgrade

Firmware Upgrade

Beore you upgrade the Access Point’s irmware, note all o your custom settings. Ater you upgrade its irmware, youmay have to re-enter all o your coniguration settings. Toupgrade the Access Point’s irmware:

Download the irmware upgrade ile rom the Linksys1.website, www.linksys.com.

Extract the irmware upgrade ile on your computer.2.

On the Firmware Upgrade screen, enter the location o 3.the irmware upgrade ile in the ield provided, or click the Browse button to ind the ile.

Click the4. Upgrade button, and ollow the on-screen

instructions.

Help inormation is available on the right side o thescreen.

8/8/2019 WAP200E_V10_UG_C_web




Administration > Reboot

On this screen you can reboot the Access Point.

Administration > Reboot

Reboot

This eature is useul when you need to remotely rebootthe Access Point.

Device Reboot To reboot the Access Point, click the Yesoption.

Click Save Settings to apply your change and the AccessPoint will reboot itsel, or click Cancel Changes to cancelyour change. Help inormation is available on the right

side o the screen.

Administration > Conig Management

On this screen you can create a backup coniguration ileor save a coniguration ile to the Access Point.

Administration > Conig Management

Conig Management

Use this screen to upload or download coniguration ilesor the Access Point.

Save Coniguration To save a backup coniguration ileon a computer, click the Save Coniguration to File buttonand ollow the on-screen instructions.

Restore Coniguration To upload a coniguration ile tothe Access Point, enter the location o the conigurationile in the ield provided, or click the Browse button to indthe ile. Then click the Load button.

Help inormation is available on the right side o thescreen.

Status > Local Network

The Local Network screen displays the Access Point’scurrent status inormation or the local network.

Inormation

Hardware Version This is the version o the Access Point’scurrent hardware.

Sotware Version This is the version o the Access Point’scurrent sotware.

Local MAC Address The MAC address o the AccessPoint’s Local Area Network (LAN) interace is displayedhere.

System Up Time This is the length o time the AccessPoint has been running.

Local Network

IP Address This shows the Access Point’s IP Address, as itappears on your local network.

8/8/2019 WAP200E_V10_UG_C_web




Subnet Mask This shows the Access Point’s SubnetMask.

To update the status inormation, click the Reresh button. Help inormation is available on the right side o

the screen.

Status > Wireless

The Wireless screen displays the Access Point’s currentstatus inormation or the wireless network(s).

Status > Wireless

Wireless Network

Mode The Access Point’s wireless network mode isdisplayed here.

SSID 1-4 MAC Address The MAC Addresses o the AccessPoint’s wireless interaces are displayed here.

SSID 1-4 The Access Point’s SSIDs that have beenconigured are displayed here.

Channel The Access Point’s Channel setting or the SSIDis shown here.

VLAN Trunk The VLAN Trunk Status is displayed here.

Priority Setting The priority setting status is displayedhere.

To update the status inormation, click the Reresh button. Help inormation is available on the right side o the screen.

Status > System Perormance

The System Perormance screen displays the AccessPoint’s status inormation or its current settings and datatransmissions.

Status > System Perormance

System PerormanceWired

Name This indicates that the statistics are or the wirednetwork, the LAN.

IP Address The Access Point’s local IP address is displayedhere.

MAC Address This shows the MAC Address o the AccessPoint’s wired interace.

Connection This shows the status o the Access Point’sconnection or the wired network.

Packets Received This shows the number o packetsreceived.

Packets Sent This shows the number o packets sent.

Bytes Received This shows the number o bytesreceived.

Bytes Sent This shows the number o bytes sent.

Error Packets Received This shows the number o errorpackets received.

Drop Received Packets This shows the number o packets being dropped ater they were received.

8/8/2019 WAP200E_V10_UG_C_web




Wireless

Name This indicates the wireless network/SSID to whichthe statistics reer.

IP Address The Access Point’s local IP address is displayed

here.

MAC Address This shows the MAC Address o the AccessPoint’s wireless interace.

Connection This shows the status o the Access Point’swireless networks.

Packets Received This shows the number o packetsreceived or each wireless network.

Packets Sent This shows the number o packets sent oreach wireless network.

Bytes Received This shows the number o bytes received

or each wireless network.Bytes Sent This shows the number o bytes sent or eachwireless network.

Error Packets Received This shows the number o errorpackets received or each wireless network.

Drop Received Packets This shows the number o packets being dropped ater they were received.

Reset Counter Press this button to reset packet statisticcounters to zeros.

To update the status inormation, click the Reresh button. Help inormation is available on the right side o the screen.

8/8/2019 WAP200E_V10_UG_C_web


25

Introduction


Appendix A

Appendix A:Troubleshooting

This appendix provides solutions to problems thatmay occur during the installation and operation o theWireless-G Exterior Access Point with Power Over Ethernet.Read the description below to solve your problems. I youcan’t ind an answer here, check the Linksys website atwww.linksys.com.

Can the Access Point act as my DHCP Server?

No. The Access Point is nothing more than a wirelesshub, and as such cannot be conigured to handle DHCPcapabilities.

Can I run an application rom a remote computer over the wireless network?

This will depend on whether or not the applicationis designed to be used over a network. Consult theapplication’s documentation to determine i it supportsoperation over a network.

Can I play multiplayer games with other users o the

wireless network?

Yes, as long as the game supports multiple playersover a LAN (local area network). Reer to the game’sdocumentation or more inormation.

What is the IEEE 802.11b standard?

It is one o the IEEE standards or wireless networks. The802.11b standard allows wireless networking hardwarerom dierent manuacturers to communicate, providedthat the hardware complies with the 802.11b standard.

The 802.11b standard states a maximum data transer rateo 11Mbps and an operating requency o 2.4GHz.

What is the IEEE 802.11g standard?

It is one o the IEEE standards or wireless networks. The

802.11g standard allows wireless networking hardwarerom dierent manuacturers to communicate, providedthat the hardware complies with the 802.11g standard.

The 802.11g standard states a maximum data transer rateo 54Mbps and an operating requency o 2.4GHz.

What IEEE 802.11b eatures are supported?

The product supports the ollowing IEEE 802.11unctions:

CSMA/CA plus Acknowledge protocol•

Multi-Channel Roaming•

Automatic Rate Selection•

RTS/CTS eature•

Fragmentation•

Power Management•

What IEEE 802.11g eatures are supported?

The product supports the ollowing IEEE 802.11gunctions:

CSMA/CA plus Acknowledge protocol•

OFDM protocol•

Multi-Channel Roaming•

Automatic Rate Selection•

RTS/CTS eature•

Fragmentation•

Power Management•

What is Ad-hoc?

An Ad-hoc wireless LAN is a group o computers, each

with a WLAN adapter, connected as an independent

wireless LAN. An Ad-hoc wireless LAN is applicable at adepartmental scale or a branch or SOHO operation.

What is Inrastructure?

An integrated wireless and wired LAN is called anInrastructure coniguration. Inrastructure is applicable toenterprise scale or wireless access to a central database,or wireless application or mobile workers.

What is roaming?

Roaming is the ability o a portable computer userto communicate continuously while moving reelythroughout an area greater than that covered by a singleAccess Point. Beore using the roaming unction, theworkstation must make sure that it is set to the samechannel number as the Access Point o the dedicatedcoverage area.

8/8/2019 WAP200E_V10_UG_C_web


26

Introduction


Appendix A

To achieve true seamless connectivity, the wirelessLAN must incorporate a number o dierent unctions.Each node and Access Point, or example, must alwaysacknowledge receipt o each message. Each node mustmaintain contact with the wireless network even when

not actually transmitting data. Achieving these unctionssimultaneously requires a dynamic RF networkingtechnology that links Access Points and nodes. In sucha system, the user’s end node undertakes a search orthe best possible access to the system. First, it evaluatessuch actors as signal strength and quality, as well as themessage load currently being carried by each AccessPoint and the distance o each Access Point to the wiredbackbone. Based on that inormation, the node nextselects the right Access Point and registers its address.Communications between end node and host computercan then be transmitted up and down the backbone.

As the user moves on, the end node’s RF transmitterregularly checks the system to determine whether itis in touch with the original Access Point or whetherit should seek a new one. When a node no longerreceives acknowledgment rom its original Access Point,it undertakes a new search. Upon inding a new AccessPoint, it then re-registers, and the communication processcontinues.

What is the ISM band?

The FCC and their counterparts outside o the U.S. have setaside bandwidth or unlicensed use in the ISM (Industrial,

Scientiic and Medical) band. Spectrum in the vicinity o 2.4 GHz, in particular, is being made available worldwide.This presents a truly revolutionary opportunity to placeconvenient high speed wireless capabilities in the handso users around the globe.

What is Spread Spectrum?

Spread Spectrum technology is a wideband radiorequency technique developed by the military or usein reliable, secure, mission-critical communicationssystems. It is designed to trade o bandwidth eiciencyor reliability, integrity, and security. In other words, morebandwidth is consumed than in the case o narrowbandtransmission, but the trade-o produces a signal thatis, in eect, louder and thus easier to detect, providedthat the receiver knows the parameters o the spread-spectrum signal being broadcast. I a receiver is not tunedto the right requency, a spread-spectrum signal lookslike background noise. There are two main alternatives,Direct Sequence Spread Spectrum (DSSS) and FrequencyHopping Spread Spectrum (FHSS).

What is DSSS? What is FHSS? And what are their

dierences?

Frequency Hopping Spread Spectrum (FHSS) uses anarrowband carrier that changes requency in a pattern

that is known to both transmitter and receiver. Properlysynchronized, the net eect is to maintain a single logicalchannel. To an unintended receiver, FHSS appears to beshort-duration impulse noise. Direct Sequence SpreadSpectrum (DSSS) generates a redundant bit pattern oreach bit to be transmitted. This bit pattern is called achip (or chipping code). The longer the chip, the greaterthe probability that the original data can be recovered.Even i one or more bits in the chip are damaged duringtransmission, statistical techniques embedded in theradio can recover the original data without the need orretransmission. To an unintended receiver, DSSS appearsas low power wideband noise and is rejected (ignored) by

most narrowband receivers.

Would the inormation be intercepted while transmitting

on air?

WLAN eatures two-old protection in security. On thehardware side, as with Direct Sequence Spread Spectrumtechnology, it has the inherent security eature o scrambling. On the sotware side, the WLAN series oersa variety o wireless security methods to enhance securityand access control. Users can set it up depending upontheir needs.

Can Linksys wireless products support fle and printer sharing?

Linksys wireless products perorm the same unction asLAN products. Thereore, Linksys wireless products canwork with NetWare, Windows NT/2000, or other LANoperating systems to support printer or ile sharing.

What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanismbased on a 40-bit shared-key algorithm, as described inthe IEEE 802.11 standard.

What is a MAC Address?

The Media Access Control (MAC) address is a uniquenumber assigned by the manuacturer to any Ethernetnetworking device, such as a network adapter, that allowsthe network to identiy it at the hardware level. For allpractical purposes, this number is usually permanent.Unlike IP addresses, which can change every time acomputer logs on to the network, the MAC address o adevice stays the same, making it a valuable identiier orthe network.

8/8/2019 WAP200E_V10_UG_C_web


27

Introduction


Appendix A

How do I avoid intererence?

Using multiple Access Points on the same channel and inclose proximity to one another will generate intererence.When employing multiple Access Points, make sure to

operate each one on a dierent channel (requency).

How do I reset the Access Point?

Press the Reset button on the back o the Access Point orabout ten seconds. This will reset the unit to its deaultsettings.

How do I resolve issues with signal loss?

There is no way to know the exact range o your wirelessnetwork without testing. Every obstacle placed betweenan Access Point and wireless PC will create signal loss.Leaded glass, metal, concrete loors, water, and walls will

inhibit the signal and reduce range. Start with your AccessPoint and your wireless PC in the same room and moveit away in small increments to determine the maximumrange in your environment.

You may also try using dierent channels, as this mayeliminate intererence aecting only one channel. Also,open the Access Point’s Web-based Utility. Click theWireless tab and then the Advanced Wireless tab. Makesure the Output Power is set to 100%.

Does the Access Point unction as a frewall?

No. The Access Point is only a bridge rom wired Ethernet

to wireless clients.

I have excellent signal strength, but I cannot see mynetwork.

Wireless security, such as WEP or WPA, is probably enabledon the Access Point, but not on your wireless adapter (orvice versa). Veriy that the same wireless security settingsare being used on all devices in your wireless network.

What is the maximum number o users the Access Point

can handle?

No more than 65, but this depends on the volume o data

and may be ewer i many users create a large amount o network traic.

WEB: I your questions are not addressed here,reer to the Linksys website, www.linksys.com

8/8/2019 WAP200E_V10_UG_C_web


28

Wireless Security Checklist


Appendix B

Appendix B:Wireless Security Checklist

Wireless networks are convenient and easy to install, sohomes with high-speed Internet access are adopting themat a rapid pace. Because wireless networking operates bysending inormation over radio waves, it can be morevulnerable to intruders than a traditional wired network.Like signals rom your cellular or cordless phones, signalsrom your wireless network can also be intercepted. Sinceyou cannot physically prevent someone rom connectingto your wireless network, you need to take some additionalsteps to keep your network secure.

1. Change the deault wireless

network name or SSID

Wireless devices have a deault wireless network nameor Service Set Identiier (SSID) set by the actory. Thisis the name o your wireless network, and can be upto 32 characters in length. Linksys wireless productsuse linksys as the deault wireless network name. Youshould change the wireless network name to somethingunique to distinguish your wireless network rom otherwireless networks that may exist around you, but do notuse personal inormation (such as your Social Securitynumber) because this inormation may be available oranyone to see when browsing or wireless networks.

2. Change the deault password

For wireless products such as access points and routers,you will be asked or a password when you want to changetheir settings. These devices have a deault password setby the actory. The Linksys deault password is admin.Hackers know these deaults and may try to use themto access your wireless device and change your network settings. To thwart any unauthorized changes, customizethe device’s password so it will be hard to guess.

3. Enable MAC address iltering

Linksys routers give you the ability to enable Media AccessControl (MAC) address iltering. The MAC address is aunique series o numbers and letters assigned to everynetworking device. With MAC address iltering enabled,wireless network access is provided solely or wirelessdevices with speciic MAC addresses. For example, you canspeciy the MAC address o each computer in your homeso that only those computers can access your wirelessnetwork.

4. Enable encryption

Encryption protects data transmitted over a wirelessnetwork. Wi-Fi Protected Access (WPA/WPA2) and WiredEquivalency Privacy (WEP) oer dierent levels o securityor wireless communication. Currently, devices that areWi-Fi certiied are required to support WPA2, but are notrequired to support WEP.

A network encrypted with WPA/WPA2 is more securethan a network encrypted with WEP, because WPA/WPA2uses dynamic key encryption. To protect the inormationas it passes over the airwaves, you should enable thehighest level o encryption supported by your network equipment.

WEP is an older encryption standard and may be the

only option available on some older devices that do notsupport WPA.

General Network Security Guidelines

Wireless network security is useless i the underlyingnetwork is not secure.

Password protect all computers on the network and•

individually password protect sensitive iles.

Change passwords on a regular basis.•

Install anti-virus sotware and personal irewall•

sotware.Disable ile sharing (peer-to-peer). Some applications•

may open ile sharing without your consent and/orknowledge.

Additional Security Tips

Keep wireless routers, access points, or gateways away•

rom exterior walls and windows.

Turn wireless routers, access points, or gateways•

o when they are not being used (at night, duringvacations).

Use strong passphrases that are at least eight characters•

in length. Combine letters and numbers to avoid usingstandard words that can be ound in the dictionary.

8/8/2019 WAP200E_V10_UG_C_web


29

Glossary


Appendix C

Appendix C:Glossary

This glossary contains some basic networking terms youmay come across when using this product.

WEB: For additional terms, please visit theglossary at www.linksys.com/glossary

Access Mode Speciies the method by which user accessis granted to the system.

Access Point A device that allows wireless-equippedcomputers and other devices to communicate with awired network. Also used to expand the range o a wireless

network.Access Proiles Allows network managers to deineproiles and rules or accessing the device. Access tomanagement unctions can be limited to user groups,which are deined by the ollowing criteria:

Ingress interaces•

Source IP address and/or Source IP subnets.•

ACE Filters in Access Control Lists (ACL) that determinewhich network traic is orwarded. An ACE is based on theollowing criteria:

Protocol•

Protocol ID•

Source Port•

Destination Port•

Wildcard Mask •

Source IP Address•

Destination IP Address•

ACL (Access Control List) Access Control Lists areused to grant, deny, or limit access devices, eatures, orapplications.

Auto-negotiation Allows 10/100 Mbps or 10/100/1000Mbps Ethernet ports to automatically establish theoptimal duplex mode, low control, and speed.

Back Pressure A mechanism used with Hal Duplex modethat enables a port not to receive a message.

Bandwidth The transmission capacity o a given deviceor network.

Bandwidth Assignments Indicates the amount o bandwidth assigned to a speciic application, user, and/orinterace.

Baud Indicates the number o signaling elementstransmitted each second.

Best Eort Indicates that traic is assigned to the lowestpriority queue, and packet delivery is not guaranteed.

Bit A binary digit.Boot To start a device and cause it to start executinginstructions.

Browser An application program that provides a way tolook at and interact with all the inormation on the WorldWide Web.

Bridge A device that connect two networks. Bridges arehardware speciic, however they are protocol independent.Bridges operate at Layer 1 and Layer 2 levels.

Broadcast Domain Devices sets that receive broadcastrames originating rom any device within a designated

set. Routers bind Broadcast domains, because routers donot orward broadcast rames.

Broadcast Storm An excessive amount o broadcastmessages simultaneously transmitted across a network by a single port. Forwarded message responses areheaped onto the network, overloading network resourcesor causing the network to time out.

Burst A packet transmission at aster than normal rates.Bursts are limited in time and only occur under speciicconditions.

Burst Size Indicates the burst size transmitted at a aster

than normal rate.Byte A unit o data that is usually eight bits long

Cable Modem A device that connects a computer to thecable television network, which in turn connects to theInternet.

CBS (Committed Burst Size) Indicates the maximumnumber o data bits transmitted within a speciic timeinterval.

CIR (Committed Inormation Rate) The data rate isaveraged over a minimum time increment.

Class Maps An aspect o Quality o Service system that is

comprised o an IP ACL and/or a MAC ACL. Class maps areconigured to match packet criteria, and are matched topackets in a irst-it ashion.

Combo Ports A single logical port with two physicalconnections, including an RJ-45 connection and a SFPconnection.

Communities Speciies a group o users which retain thesame system access rights.

8/8/2019 WAP200E_V10_UG_C_web


30

Glossary


Appendix C

CoS (Class o Service) The 802.1p priority scheme. CoSprovides a method or tagging packets with priorityinormation. A CoS value between 0-7 is added to theLayer II header o packets, where zero is the lowest priorityand seven is the highest.

DDNS (Dynamic Domain Name System) Allows thehosting o a website, FTP server, or e-mail server with aixed domain name (e.g., www.xyz.com) and a dynamic IPaddress.

Deault Gateway A device that orwards Internet traicrom your local area network.

DHCP (Dynamic Host Coniguration Protocol) Anetworking protocol that allows administrators to assigntemporary IP addresses to network computers by “leasing”an IP address to a user or a limited amount o time, insteado assigning permanent IP addresses.

DHCP Clients An Internet host using DHCP to obtainconiguration parameters, such as a network address.

DHCP Server An Internet host that returns conigurationparameters to DHCP clients.

DNS (Domain Name Server) The IP address o your ISP’sserver, which translates the names o websites into IPaddresses.

Domain A speciic name or a network o computers.

Download To receive a ile transmitted over a network.

DSL (Digital Subscriber Line) An always-on broadband

connection over traditional phone lines.DSCP (DiServ Code Point) Provides a method o tagging IP packets with QoS priority inormation.

Dynamic IP Address A temporary IP address assigned bya DHCP server.

EIGRP (Enhanced Interior Gateway RoutingProtocol) Provides ast convergence, support orvariable-length subnet mask, and supports multiplenetwork layer protocols.

Encryption Encoding data transmitted in a network.

Ethernet IEEE standard network protocol that speciies

how data is placed on and retrieved rom a commontransmission medium.

Firmware The programming code that runs a networkingdevice.

Flow Control Enables lower speed devices tocommunicate with higher speed devices. This isimplemented by the higher speed device reraining romsending packets.

FTP (File Transer Protocol) A protocol used to transeriles over a TCP/IP network.

Full Duplex The ability o a networking device to receiveand transmit data simultaneously.

GARP (General Attributes Registration Protocol)Registers client stations into a multicast domain.

Gateway A device that interconnects networks withdierent, incompatible communications protocols.

GBIC (GigaBit Interace Converter) A hardware moduleused to attach network devices to iber-based transmissionsystems. GBIC converts the serial electrical signals to serialoptical signals and vice versa.

GVRP (GARP VLAN Registration Protocol) Registersclient stations into a VLANs.

Hal Duplex Data transmission that can occur in twodirections over a single line, but only one direction at atime.

HTTP (HyperText Transport Protocol) Thecommunications protocol used to connect to servers onthe World Wide Web.

HTTPS (HyperText Transport Protocol Secure) Anextension to the standard HTTP protocol that providesconidentiality by encrypting the traic rom the website.By deault this protocol uses TCP port 443.

ICMP (Internet Control Message Protocol) Allows thegateway or destination host to communicate with thesource host. For example, to report a processing error.

IGMP (Internet Group Management Protocol) Allows

hosts to notiy their local switch or router that they wantto receive transmissions assigned to a speciic multicastgroup.

IP (Internet Protocol) A protocol used to send data overa network.

IP Address The address used to identiy a computer ordevice on a network.

IPCONFIG A Windows 2000 and XP utility that displaysthe IP address or a particular networking device.

IPSec (Internet Protocol Security) A VPN protocol usedto implement secure exchange o packets at the IP layer.

ISP (Internet Service Provider) A company that providesaccess to the Internet.

Jumbo Frames Enable transporting identical data inewer rames. Jumbo Frames reduce overhead, lowerprocessing time, and ensure ewer interrupts.

LAG (Link Aggregated Group) Aggregates ports orVLANs into a single virtual port or VLAN.

LAN The computers and networking products that makeup your local network.

8/8/2019 WAP200E_V10_UG_C_web


31

Glossary


Appendix C

MAC (Media Access Control) Address The uniqueaddress that a manuacturer assigns to each networkingdevice.

Mask A ilter that includes or excludes certain values, or

example parts o an IP address.Mbps (MegaBits Per Second) One million bits persecond; a unit o measurement or data transmission.

MD5 (Message Digest 5) An algorithm that produces a128-bit hash. MD5 is a variation o MD4, and increases MD4security. MD5 veriies the integrity o the communicationand authenticates the origin o the communication.

MDI (Media Dependent Interace) A cable used or endstations.

MDIX (Media Dependent Interace with Crossover) Acable used or hubs and switches.

MIB (Management Inormation Base) MIBs containinormation describing speciic aspects o network components.

Multicast Transmits copies o a single packet to multipleports.

Network A series o computers or devices connected orthe purpose o data sharing, storage, and/or transmissionbetween users.

NMS (Network Management System) An interace thatprovides a method o managing a system.

OID (Object Identiier) Used by SNMP to identiy

managed objects. In the SNMP Manager/Agent network management paradigm, each managed object must havean OID to identiy it.

Packet A unit o data sent over a network.

Ping (Packet INternet Groper) An Internet utility usedto determine whether a particular IP address is online.

Policing Determines i traic levels are within a speciiedproile. Policing manages the maximum traic rate usedto send or receive packets on an interace.

Port The connection point on a computer or networkingdevice used or plugging in cables or adapters.

Port Mirroring Monitors and mirrors network traic byorwarding copies o incoming and outgoing packetsrom one port to a monitoring port.

Power over Ethernet (PoE) A technology enabling anEthernet network cable to deliver both data and power.

QoS (Quality o Service) Provides policies that containsets o ilters (rules). QoS allows network managersto decide how and what network traic is orwardedaccording to priorities, application types, and source anddestination addresses.

RADIUS (Remote Authentication Dial-In UserService) A protocol that uses an authentication server tocontrol network access.

RJ-45 (Registered Jack-45) An Ethernet connector that

holds up to eight wires.RMON (Remote Monitoring) Provides network inormation to be collected rom a single workstation.

Router A networking device that connects multiplenetworks together.

RSTP (Rapid Spanning Tree Protocol) Detects and usesnetwork topologies that allow a aster convergence o thespanning tree, without creating orwarding loops.

Server Any computer whose unction in a network is toprovide user access to iles, printing, communications,and other services.

SMTP (Simple Mail Transer Protocol) The standarde-mail protocol on the Internet.

SNMP (Simple Network Management Protocol) Awidely used network monitoring and control protocol.

SSH Secure Shell. A utility that uses strong authenticationand secure communications to log in to another computerover a network.

SSL (Secure Socket Layer) Encryption technology orthe Internet used to provide secure transactions, such asthe transmission o credit card numbers or e-commerce.

Static IP Address A ixed address assigned to a computer

or device that is connected to a network.

STP (Spanning Tree Protocol) Prevents loops in network traic. The Spanning Tree Protocol (STP) provides treetopography or any arrangement o bridges. STP providesone path between end stations on a network, eliminatingloops.

Subnet (Sub-network) Subnets are portions o anetwork that share a common address component. InTCP/IP networks, devices that share a preix are part o the same subnet. For example, all devices with a preix o 157.100.100.100 are part o the same subnet.

Subnet Mask An address code that determines the sizeo the network.

Switch Filters and orwards packets between LANsegments. Switches support any packet protocol type.

TACACS+ (Terminal Access Controller Access ControlSystem Plus) Proprietary Cisco enhancement to TerminalAccess Controller Access Control System ( TACACS). Providesadditional support or authentication, authorization, andaccounting.

8/8/2019 WAP200E_V10_UG_C_web


32

Glossary


Appendix C

TCP (Transmission Control Protocol) A network protocolor transmitting data that requires acknowledgementrom the recipient o data sent.

TCP/IP (Transmission Control Protocol/Internet

Protocol) A set o instructions PCs use to communicateover a network.

Telnet A user command and TCP/IP protocol used oraccessing remote PCs.

TFTP (Trivial File Transer Protocol) A version o theTCP/IP FTP protocol that has no directory or passwordcapability.

Throughput The amount o data moved successullyrom one node to another in a given time period.

Trunking Link Aggregation. Optimizes port usage bylinking a group o ports together to orm a single trunk

(aggregated groups).TX Rate Transmission Rate.

UDP (User Data Protocol) Communication protocol thattransmits packets but does not guarantee their delivery.

Upgrade To replace existing sotware or irmware with anewer version.

Upload To transmit a ile over a network.

URL (Uniorm Resource Locator) The address o a ilelocated on the Internet.

VLAN (Virtual Local Area Networks) Logical subgroups

that constitute a Local Area Network (LAN). This is done insotware rather than deining a hardware solution.

WAN (Wide Area Network) Networks that cover a largegeographical area.

Wildcard Mask Speciies which IP address bits areused, and which bits are ignored. A wild card mask o 255.255.255.255 indicates that no bit is important.A wildcard o 0.0.0.0 indicates that all the bits areimportant.

For example, i the destination IP address is 149.36.184.198and the wildcard mask is 255.36.184.00, the irst two bitso the IP address are used, while the last two bits are

ignored.

8/8/2019 WAP200E_V10_UG_C_web


33

Specifications


Appendix D

Appendix D:Speciications

SpecifcationsModel WAP200E

Standards IEEE802.11g, IEEE802.11b,IEEE802.3, IEEE802.3u,IEEE802.3a (Power OverEthernet), 802.1p (QoSpriority), 802.1Q (VLAN), 802.1X(Security Authentication),802.11i - Ready (SecurityWPA2), 802.11e - Ready (WMM& U-APSD), 802.11F (WirelessRoaming)

Ports 1 Ethernet, 1 External AntennaButtons Reset

Cabling Type UTP CAT 5

LEDs Power, Ethernet, Wireless

Operating System Linux

Management

SNMP Version 1, 2 and 2c

Operating Modes

Access Point Access Point Mode,point-to-point Bridge Mode,

point-to-multipoint BridgeMode, Repeater Mode

Wireless

Spec/Modulation 802.11b/DSSS, 11g/ODFM

Data Rates 11b: 1, 2, 5.5, 11 Mbps,11g: 6, 9, 11, 12, 18, 24, 36, 48,54 Mbps

Channels 11 North America,13 Europe (ETSI and Japan)Auto-channel selection

# o Internal Ant. 2x 6dBi (directional)

Ant. connector type Reverse Polarity Female N-type

Detachable y/n/na y (sold separately)

RF Pwr (EIRP) in dBm 11.g: Typical - 16.5dBm,11.b: Typical - 17dBm

Antenna Gain in dBi Internal antenna: 6dBi

Adjustable power y

Receiver Sensitivity 11.g: 54Mbps@ -65dBm,11.b: 11Mbps@ -85dBM

SecurityWEP/WPA/WPA2 WEP, WPA-PSK, WPA2-PSK,

WPA-ENT, WPA2-ENT

Connection Control Wireless Connection Control:MAC-Based

SSID Broadcast SSID Broadcast Enable/Disable

802.1X IEEE 802.1X support

Wireless Client Isolation Wireless Client devices canbe isolated rom each othereither within an SSID orbetween two SSIDs.

Both isolation modes can beenabled in the same time.

Web-based UtilityAccess Control HTTP/HTTPS, wireless client

web GUI access control

Wireless Security

WEP bits 64, 128

WPA bits & params 128 - TKIP/AES

WPA2 bits & params 256 - AES

SSID Broadcast on/o Yes

Client Isolation Yes

MAC-based WirelessConnection Control Yes

Wireless Web GUIAccess on/o Yes

Quality o Service

QoS 4 queues

WMM wireless trafcprioritization

General

Wireless roaming based on

IAPP (802.11F)Auto-channel selection

8/8/2019 WAP200E_V10_UG_C_web


34

Specifications


Appendix D

Environmental

Dimensions 6.42" x 8.07" x 2.17"163 x 205 x 55mm

Weight 2.47 lb (1.121 kg)

Mounting options Industrial-strength,weather-proo housing, NEMAIP53 rating, lighting protectionor outdoor enclosure, ceilingor wall mountable

Power 48V DC, 350mA

Max Power Draw 4.8 Watt

PoE In Yes

PoE Out No

Certication FCC, IC, CE

Operating Temp. -4 to 140ºF (-20 to 60ºc)

Storage Temp. -4 to 140ºF (-20 to 60ºc)

Operating Humidity 5 to 95%, noncondensing

Storage Humidity 5 to 95%, noncondensing

8/8/2019 WAP200E_V10_UG_C_web


35

Warranty and Regulatory Information


Appendix E

Appendix E:Warranty and Regulatory

InormationLimited Warranty

Linksys warrants to You that, or a period o three years(the "Warranty Period"), your Linksys Product will besubstantially ree o deects in materials and workmanshipunder normal use. Your exclusive remedy and Linksys’entire liability under this warranty will be or Linksys atits option to repair or replace the Product or reund Yourpurchase price less any rebates. This limited warrantyextends only to the original purchaser.

I the Product proves deective during the WarrantyPeriod call Linksys Technical Support in order to obtaina Return Authorization Number, i applicable. BE SURETO HAVE YOUR PROOF OF PURCHASE ON HAND WHENCALLING. I You are requested to return the Product, mark the Return Authorization Number clearly on the outsideo the package and include a copy o your original proo o purchase. RETURN REQUESTS CANNOT BE PROCESSEDWITHOUT PROOF OF PURCHASE. You are responsibleor shipping deective Products to Linksys. Linksys paysor UPS Ground shipping rom Linksys back to You only.Customers located outside o the United States o Americaand Canada are responsible or all shipping and handling

charges.ALL IMPLIED WARRANTIES AND CONDITIONS OFMERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE ARE LIMITED TO THE DURATION OFTHE WARRANTY PERIOD. ALL OTHER EXPRESS ORIMPLIED CONDITIONS, REPRESENTATIONS ANDWARRANTIES, INCLUDING ANY IMPLIED WARRANTY OFNON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictionsdo not allow limitations on how long an implied warrantylasts, so the above limitation may not apply to You. Thiswarranty gives You speciic legal rights, and You may alsohave other rights which vary by jurisdiction.

This warranty does not apply i the Product (a) has beenaltered, except by Linksys, (b) has not been installed,operated, repaired, or maintained in accordance withinstructions supplied by Linksys, or (c) has been subjectedto abnormal physical or electrical stress, misuse,negligence, or accident. In addition, due to the continualdevelopment o new techniques or intruding upon andattacking networks, Linksys does not warrant that theProduct will be ree o vulnerability to intrusion or attack.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENTWILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUEOR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THETHEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING

OUT OF OR RELATED TO THE USE OF OR INABILITY TOUSE THE PRODUCT (INCLUDING ANY SOFTWARE), EVENIF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITYEXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.The oregoing limitations will apply even i any warranty orremedy provided under this Agreement ails o its essentialpurpose. Some jurisdictions do not allow the exclusion orlimitation o incidental or consequential damages, so theabove limitation or exclusion may not apply to You.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,CA 92623.

FCC Statement

This device complies with Part 15 o the FCC Rules.Operation is subject to the ollowing two conditions: (1)This device may not cause harmul intererence, and (2) thisdevice must accept any intererence received, includingintererence that may cause undesired operation.

This product has been tested and complies with thespeciications or a Class B digital device, pursuant to Part15 o the FCC Rules. These limits are designed to providereasonable protection against harmul intererence ina residential installation. This equipment generates,uses, and can radiate radio requency energy and, i notinstalled and used according to the instructions, maycause harmul intererence to radio communications.However, there is no guarantee that intererence will notoccur in a particular installation. I this equipment doescause harmul intererence to radio or television reception,which is ound by turning the equipment o and on, theuser is encouraged to try to correct the intererence byone or more o the ollowing measures:

Reorient or relocate the receiving antenna•

Increase the separation between the equipment or•

devicesConnect the equipment to an outlet other than the•

receiver’s

Consult a dealer or an experienced radio/TV technician•

or assistance

FCC Caution: Any changes or modiications not expresslyapproved by the party responsible or compliance couldvoid the user’s authority to operate this equipment.

8/8/2019 WAP200E_V10_UG_C_web


36



Appendix E

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposurelimits set orth or an uncontrolled environment. Thisequipment should be installed and operated with

minimum distance 20cm between the radiator and yourbody.

This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.

The availability o some speciic channels and/oroperational requency bands are country dependentand are irmware programmed at the actory to matchthe intended destination. The irmware setting is notaccessible by the end user.

Saety Notices

Caution: To reduce the risk o ire, use only No.26 AWG orlarger telecommunication line cord.

Do not use this product near water, or example, in a wetbasement or near a swimming pool.

Avoid using this product during an electrical storm. Theremay be a remote risk o electric shock rom lightning.

WARNING: This product contains lead, knownto the State o Caliornia to cause cancer, andbirth deects or other reproductive harm. Washhands ater handling.

Industry Canada Statement

This device complies with Industry Canada ICES-003 andRSS210 rules.

Operation is subject to the ollowing two conditions:

This device may not cause intererence and1.

This device must accept any intererence, including2.intererence that may cause undesired operation o thedevice. This device has been designed to operate withan antenna having a maximum gain o 9 dBi. Antenna

having a higher gain is strictly prohibited per regulationso Industry Canada. The required antenna impedanceis 50 ohms.

To reduce potential radio intererence to other users,the antenna type and its gain should be so chosenthat the EIRP is not more than required or successulcommunication.

Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limitsset orth or an uncontrolled environment. This equipmentshould be installed and operated with minimum distance

20cm between the radiator & your body.This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.

Avis d’Industrie Canada

Cet appareil est conorme aux normes NMB003 et RSS210d’Industrie Canada.

L’utilisation de ce dispositi est autorisée seulement auxconditions suivantes :

il ne doit pas produire de brouillage et1.

il doit accepter tout brouillage radioélectrique reçu,2. même si ce brouillage est susceptible de compromettrele onctionnement du dispositi. Le dispositi a étéconçu pour onctionner avec une antenne ayant un gainmaximum de 9 dBi. Les règlements d’Industrie Canadainterdisent strictement l’utilisation d’antennes dont legain est supérieur à cette limite. L’impédance requisede l’antenne est de 50 ohms.Ain de réduire le risque d’interérence aux autresutilisateurs, le type d’antenne et son gain doiventêtre choisis de açon à ce que la puissance isotroperayonnée équivalente (p.i.r.e.) ne soit pas supérieureau niveau requis pour obtenir une communication

satisaisante.

Avis d’Industrie Canada concernant l’exposition

aux radioréquences :

Ce matériel est conorme aux limites établies par ICen matière d’exposition aux radioréquences dans unenvironnement non contrôlé. Ce matériel doit être installéet utilisé à une distance d’au moins 20 cm entre l’antenneet le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenneou d’un autre émetteur, ou onctionner avec une autre

antenne ou un autre émetteur.

8/8/2019 WAP200E_V10_UG_C_web


37



Appendix E

User Inormation or Consumer Products

Covered by EU Directive 2002/96/EC on

Waste Electric and Electronic Equipment

(WEEE)This document contains important inormation or userswith regards to the proper disposal and recycling o Linksys products. Consumers are required to comply withthis notice or all electronic products bearing the ollowingsymbol:

English - Environmental Inormation or Customers inthe European Union

European Directive 2002/96/EC requires that the equipmentbearing this symbol on the product and/or its packaging mustnot be disposed o with unsorted municipal waste. The symbolindicates that this product should be disposed o separatelyrom regular household waste streams. It is your responsibility todispose o this and other electric and electronic equipment viadesignated collection acilities appointed by the government orlocal authorities. Correct disposal and recycling will help prevent

potential negative consequences to the environment andhuman health. For more detailed inormation about the disposalo your old equipment, please contact your local authorities,waste disposal service, or the shop where you purchased theproduct.

Български (Bulgarian) - Информация относноопазването на околната среда за потребители вЕвропейския съюз

Европейска директива 2002/96/EC изисква уредите, носещитози символ върху изделието и/или опаковката му, да несе изхвърля т с несортирани битови отпадъци. Символътобозначава, че изделието трябва да се изхвърля отделно от

сметосъбирането на обикновените битови отпадъци. Вашае отговорността този и другите електрически и електронниуреди да се изхвърлят в предварително определени отдържавните или общински органи специализирани пунктовеза събиране. Правилното изхвърляне и рециклиранеще спомогнат да се предотвратят евентуални вредни заоколната среда и здравето на населението последствия. Запо-подробна информация относно изхвърлянето на вашитестари уреди се обърнете към местните власти, службите засметосъбиране или магазина, от който сте закупили уреда.

Ceština (Czech) - Inormace o ochraně životníhoprostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označenétímto symbolem na produktu anebo na obalu bylo likvidovános netříděným komunálním odpadem. Tento symbol udává,

že daný produkt musí být likvidován odděleně od běžnéhokomunálního odpadu. Odpovídáte za likvidaci tohoto produktua dalších elektrických a elektronických zařízení prostřednictvímurčených sběrných míst stanovených vládou nebo místnímiúřady. Správná likvidace a recyklace pomáhá předcházetpotenciálním negativním dopadům na životní prostředí a lidskézdraví. Podrobnější inormace o likvidaci starého vybavení silaskavě vyžádejte od místních úřadů, podniku zabývajícího selikvidací komunálních odpadů nebo obchodu, kde jste produktzakoupili.

Dansk (Danish) - Miljøinormation or kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol

på produktet og/eller emballagen ikke må bortskaes somusorteret kommunalt aald. Symbolet betyder, at dette produktskal bortskaes adskilt ra det almindelige husholdningsaald.Det er dit ansvar at bortskae dette og andet elektrisk ogelektronisk udstyr via bestemte indsamlingssteder udpegeta staten eller de lokale myndigheder. Korrekt bortskaelseog genvinding vil hjælpe med til at undgå mulige skader ormiljøet og menneskers sundhed. Kontakt venligst de lokalemyndigheder, renovationstjenesten eller den butik, hvor duhar købt produktet, angående mere detaljeret inormation ombortskaelse a dit gamle udstyr.

Deutsch (German) - Umweltinormation ür Kundeninnerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technischeAusrüstung, die direkt am Gerät und/oder an der Verpackung mitdiesem Symbol versehen ist , nicht zusammen mit unsortiertemGemeindeaball entsorgt werden dar. Das Symbol weist darau hin, dass das Produkt von regulärem Haushaltmüll getrenntentsorgt werden sollte. Es liegt in Ihrer Verantwortung, diesesGerät und andere elektrische und elektronische Geräte überdie daür zuständigen und von der Regierung oder örtlichenBehörden dazu bestimmten Sammelstellen zu entsorgen.Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,potentielle negative Folgen ür Umwelt und die menschlicheGesundheit zu vermeiden. Wenn Sie weitere Inormationen zurEntsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte andie örtlichen Behörden oder städtischen Entsorgungsdiensteoder an den Händler, bei dem Sie das Produkt erworben haben.

8/8/2019 WAP200E_V10_UG_C_web


38



Appendix E

Eesti (Estonian) - Keskkonnaalane inormatsioonEuroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt onseadmeid, millel on tootel või pakendil käesolev sümbol ,keelatud kõrvaldada koos sorteerimata olmejäätmetega. See

sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistestolmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalikeametiasutuste poolt ette nähtud kogumispunktide kaudu.Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältidavõimalikke negatiivseid tagajärgi keskkonnale ning inimestetervisele. Vanade seadmete kõrvaldamise kohta täpsemainormatsiooni saamiseks võtke palun ühendust kohalikeametiasutustega, jäätmekäitlusirmaga või kauplusega, kust tetoote ostsite.

Español (Spanish) - Inormación medioambiental paraclientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos quelleven este símbolo en el propio aparato y/o en su embalajeno deben eliminarse junto con otros residuos urbanos noseleccionados. El símbolo indica que el producto en cuestióndebe separarse de los residuos domésticos convencionales convistas a su eliminación. Es responsabilidad suya desechar este ycualesquiera otros aparatos eléctricos y electrónicos a través delos puntos de recogida que ponen a su disposición el gobierno ylas autoridades locales. Al desechar y reciclar correctamente estosaparatos estará contribuyendo a evitar posibles consecuenciasnegativas para el medio ambiente y la salud de las personas. Sidesea obtener inormación más detallada sobre la eliminaciónsegura de su aparato usado, consulte a las autoridades locales,al servicio de recogida y eliminación de residuos de su zona o

pregunte en la tienda donde adquirió el producto.

ξλληνικά (Greek) - Στοιχεία περιβαλλοντικήςπροστασίας για πελάτες εντός της ΕυρωπαϊκήςΈνωσης

Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίοςφέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικάαπορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θαπρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακάαπορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντοςκαι άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω τωνκαθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι

οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψηπιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.Για περισσότερες πληροφορίες σχετικά με την απόρριψη τουπαλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικέςαρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίοαγοράσατε το προϊόν.

Français (French) - Inormations environnementalespour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipementsur lequel est apposé ce symbole sur le produit et/ou sonemballage ne soit pas jeté avec les autres ordures ménagères. Ce

symbole indique que le produit doit être éliminé dans un circuitdistinct de celui pour les déchets des ménages. Il est de votreresponsabilité de jeter ce matériel ainsi que tout autre matérielélectrique ou électronique par les moyens de collecte indiquéspar le gouvernement et les pouvoirs publics des collectivitésterritoriales. L’élimination et le recyclage en bonne et due ormeont pour but de lutter contre l’impact néaste potentiel de cetype de produits sur l’environnement et la santé publique. Pourplus d’inormations sur le mode d’élimination de votre ancienéquipement, veuillez prendre contact avec les pouvoirs publicslocaux, le service de traitement des déchets, ou l’endroit où vousavez acheté le produit.

Italiano (Italian) - Inormazioni relative all’ambienteper i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiaturecontrassegnate con questo simbolo sul prodotto e/osull’imballaggio non siano smaltite insieme ai riiuti urbaninon dierenziati. Il simbolo indica che questo prodotto nondeve essere smaltito insieme ai normali riiuti domestici. Èresponsabilità del proprietario smaltire sia questi prodotti siale altre apparecchiature elettriche ed elettroniche mediantele speciiche strutture di raccolta indicate dal governo o daglienti pubblici locali. Il corretto smaltimento ed il riciclaggioaiuteranno a prevenire conseguenze potenzialmente negativeper l’ambiente e per la salute dell’essere umano. Per ricevereinormazioni più dettagliate circa lo smaltimento delle vecchie

apparecchiature in Vostro possesso, Vi invitiamo a contattare glienti pubblici di competenza, il servizio di smaltimento riiuti o ilnegozio nel quale avete acquistato il prodotto.

Latviešu valoda (Latvian) - Ekoloģiska inormācijaklientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienotazīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkstizmest nešķirotā veidā kopā ar komunālajiem atkritumiem(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmēto, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā arparastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šoun citas elektriskas un elektroniskas ierīces izmest atkritumos,

izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, konodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumosun pārstrāde tiek veikta pareizi, tad mazinās iespējamaiskaitējums dabai un cilvēku veselībai. Sīkākas ziņas parnovecojuša aprīkojuma izmešanu atkritumos jūs varat saņemtvietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,kur iegādājāties šo izstrādājumu.

8/8/2019 WAP200E_V10_UG_C_web


39



Appendix E

Lietuvškai (Lithuanian) - Aplinkosaugos inormacija,skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri irkurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),negalima šalinti kartu su nerūšiuotomis komunalinėmis

atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirainuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kadši ir kita elektros ar elektroninė įranga būtų šalinama per tamtikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimosistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengtagalimos žalos aplinkai ir žmonių sveikatai. Daugiau inormacijosapie jūsų senos įrangos šalinimą gali pateikti vietinės valdžiosinstitucijos, atliekų šalinimo tarnybos arba parduotuvės, kurioseįsigijote tą gaminį.

Malti (Maltese) - Inormazzjoni Ambjentali għal Klijentil-Unjoni Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun ih is-

simbolu uq il-prodott u/jew uq l-ippakkjar ma jistax jintremama’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindikali dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmidan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettronikupermezz ta’ aċilitajiet ta’ ġbir appuntati apposta mill-gvern jewmill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent ugħas-saħħa tal-bniedem. Għal aktar inormazzjoni dettaljatadwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattjalill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jewil-ħanut minn ejn xtrajt il-prodott.

Magyar (Hungarian) - Környezetvédelmi inormáció azeurópai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogyazokat a termékeket, amelyeken, és/vagy amelyek csomagolásánaz alábbi címke megjelenik, tilos a többi szelektálatlan lakosságihulladékkal együtt kidobni. A címke azt jelöli, hogy az adotttermék kidobásakor a szokványos háztartási hulladékelszállításirendszerektõl elkülönített eljárást kell alkalmazni. Az Önelelõssége, hogy ezt, és más elektromos és elektronikusberendezéseit a kormányzati vagy a helyi hatóságok általkijelölt gyűjtõredszereken keresztül számolja el. A megelelõhulladékeldolgozás segít a környezetre és az emberi egészségrepotenciálisan ártalmas negatív hatások megelõzésében. Haelavult berendezéseinek elszámolásához további részletes

inormációra van szüksége, kérjük, lépjen kapcsolatba a helyihatóságokkal, a hulladékeldolgozási szolgálattal, vagy azzalüzlettel, ahol a terméket vásárolta.

Nederlands (Dutch) - Milieu-inormatie voor klantenin de Europese Unie

De Europese Richtlijn 2002/96/EC schrijt voor dat apparatuur dieis voorzien van dit symbool op het product o de verpakking,niet mag worden ingezameld met niet-gescheiden huishoudelijk

aval. Dit symbool geet aan dat het product apart moet wordeningezameld. U bent zel verantwoordelijk voor de vernietigingvan deze en andere elektrische en elektronische apparatuur via dedaarvoor door de landelijke o plaatselijke overheid aangewezeninzamelingskanalen. De juiste vernietiging en recycling vandeze apparatuur voorkomt mogelijke negatieve gevolgen voorhet milieu en de gezondheid. Voor meer inormatie over hetvernietigen van uw oude apparatuur neemt u contact op metde plaatselijke autoriteiten o avalverwerkingsdienst, o met dewinkel waar u het product hebt aangeschat.

Norsk (Norwegian) - Miljøinormasjon or kunder i EU

EU-direktiv 2002/96/EF krever at utstyr med ølgende symbol

avbildet på produktet og/eller pakningen, ikke må kastessammen med usortert avall. Symbolet indikerer at detteproduktet skal håndteres atskilt ra ordinær avallsinnsamlingor husholdningsavall. Det er ditt ansvar å kvitte deg meddette produktet og annet elektrisk og elektronisk avall via egneinnsamlingsordninger slik myndighetene eller kommunenebestemmer. Korrekt avallshåndtering og gjenvinning vilvære med på å orhindre mulige negative konsekvenser ormiljø og helse. For nærmere inormasjon om håndtering avdet kasserte utstyret ditt, kan du ta kontakt med kommunen,en innsamlingsstasjon or avall eller butikken der du kjøpteproduktet.

Polski (Polish) - Inormacja dla klientów w UniiEuropejskiej o przepisach dotyczących ochronyśrodowiska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzętoznaczony symbolem znajdującym się na produkcie i/lub jegoopakowaniu nie był wyrzucany razem z innymi niesortowanymiodpadami komunalnymi. Symbol ten wskazuje, że produktnie powinien być usuwany razem ze zwykłymi odpadami zgospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych orazelektronicznych w punktach odbioru wyznaczonych przez władzekrajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposóbi jego recykling pomogą zapobiec potencjalnie negatywnymkonsekwencjom dla środowiska i zdrowia ludzkiego. W celu

uzyskania szczegółowych inormacji o usuwaniu starego sprzętu,prosimy zwrócić się do lokalnych władz, służb oczyszczaniamiasta lub sklepu, w którym produkt został nabyty.

8/8/2019 WAP200E_V10_UG_C_web


40



Appendix E

Português (Portuguese) - Inormação ambiental paraclientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamentoque exibe este símbolo no produto e/ou na sua embalagemnão seja eliminado junto com os resíduos municipais não

separados. O símbolo indica que este produto deve sereliminado separadamente dos resíduos domésticos regulares.É da sua responsabilidade eliminar este e qualquer outroequipamento eléctrico e electrónico através dos instalaçõesde recolha designadas pelas autoridades governamentais oulocais. A eliminação e reciclagem correctas ajudarão a preveniras consequências negativas para o ambiente e para a saúdehumana. Para obter inormações mais detalhadas sobre aorma de eliminar o seu equipamento antigo, contacte asautoridades locais, os serviços de eliminação de resíduos ou oestabelecimento comercial onde adquiriu o produto.

Română (Romanian) - Inormaţii de mediu pentru

clienţii din Uniunea EuropeanăDirectiva europeană 2002/96/CE impune ca echipamentele careprezintă acest simbol pe produs şi/sau pe ambalajul acestuia sănu ie casate împreună cu gunoiul menajer municipal. Simbolulindică aptul că acest produs trebuie să ie casat separat degunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţiacest produs şi alte echipamente electrice şi electronice prinintermediul unităţilor de colectare special desemnate de guvernsau de autorităţile locale. Casarea şi reciclarea corecte vor ajutala prevenirea potenţialelor consecinţe negative asupra sănătăţiimediului şi a oamenilor. Pentru mai multe inormaţii detaliatecu privire la casarea acestui echipament vechi, contactaţiautorităţile locale, serviciul de salubrizare sau magazinul de lacare aţi achiziţionat produsul.

Slovenčina (Slovak) - Inormácie o ochrane životnéhoprostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmtosymbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom.Symbol znamená, že produkt by sa mal likvidovať oddeleneod bežného odpadu z domácností. Je vašou povinnosťoulikvidovať toto i ostatné elektrické a elektronické zariadeniaprostredníctvom špecializovaných zberných zariadení určenýchvládou alebo miestnymi orgánmi. Správna likvidácia a recykláciapomôže zabrániť prípadným negatívnym dopadom na životnéprostredie a zdravie ľudí. Ak máte záujem o podrobnejšie

inormácie o likvidácii starého zariadenia, obráťte sa, prosím, namiestne orgány, organizácie zaoberajúce sa likvidáciou odpadovalebo obchod, v ktorom ste si produkt zakúpili.

Slovenčina (Slovene) - Okoljske inormacije za strankev Evropski uniji

Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,označene s tem simbolom – na izdelku in/ali na embalaži – medobičajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba

izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.Vaša odgovornost je, da to in preostalo električno in elektronskoopremo odnesete na posebna zbirališča, ki jih določijodržavne ustanove ali lokalna uprava. S pravilnim odlaganjemin recikliranjem boste preprečili morebitne škodljive vplive naokolje in zdravje ljudi. Če želite izvedeti več o odlaganju stareopreme, se obrnite na lokalno upravo, odpad ali trgovino, kjerste izdelek kupili.

Suomi (Finnish) - Ympäristöä koskevia tietoja EU-alueen asiakkaille

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämäsymboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa

ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.Symboli merkitsee sitä, että tämä tuote on hävitettävä erillääntavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittäätämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteetviemällä tuote tai tuotteet viranomaisten määräämäänkeräyspisteeseen. Laitteiston oikea hävittäminen estäämahdolliset kielteiset vaikutukset ympäristöön ja ihmistenterveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavastasaa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitämyymälästä, josta ostit tuotteen.

Svenska (Swedish) - Miljöinormation ör kunder iEuropeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning meddenna symbol på produkten och/eller örpackningen inte årkastas med osorterat kommunalt avall. Symbolen visar att dennaprodukt bör kastas eter att den avskiljts rån vanligt hushållsavall.Det aller på ditt ansvar att kasta denna och annan elektrisk ochelektronisk utrustning på astställda insamlingsplatser utseddaav regeringen eller lokala myndigheter. Korrekt kassering ochåtervinning skyddar mot eventuella negativa konsekvenserör miljön och personhälsa. För mer detaljerad inormation omkassering av din gamla utrustning kontaktar du dina lokalamyndigheter, avallshanteringen eller butiken där du köpteprodukten.

WEB: For additional inormation, please visitwww.linksys.com

8/8/2019 WAP200E_V10_UG_C_web


Contact InformationAppendix F

Appendix F:Contact Inormation

Linksys Contact Inormation

Website http://www.linksys.com

E-Mail [email protected]

FTP Site tp.linksys.com

Advice Line 800-546-5797 (LINKSYS)

Support 800-326-7114

RMA (Return Merchandise

Authorization)949-823-3000

Fax 949-823-3002

NOTE: Details on warranty and RMA issuescan be ound in the Warranty and RegulatoryInormation section o this Guide.

wap200e_v10_ug_c_web

Documents