voice over internet protocol (voip)

Journal of Information Engineering and Applications www.iiste.org

ISSN 2224-5782 (print) ISSN 2225-0506 (online)

Vol.3, No.4, 2013

18

Voice over Internet Protocol (VOIP): Overview,

Direction And Challenges 1 U. R. ALO and

2 NWEKE HENRY FIRDAY

Department of Computer Science

Ebonyi State University Abakaliki, Nigeria 1Email:- [email protected] 2Email: [email protected]

ABSTRACT

Voice will remain a fundamental communication media that cuts across people of all walks of life. It is therefore

important to make it cheap and affordable. To be reliable and affordable over the common Public Switched

Telephone Network, change is therefore inevitable to keep abreast with the global technological change. It is on this

basis that this paper tends to critically review this new technology VoIP, x-raying the different types. It further more

discusses in detail the VoIP system, VoIP protocols, and a comparison of different VoIP protocols. The compression

algorithm used to save network bandwidth in VoIP, advantages of VoIP and problems associated with VoIP

implementation were also critically examined. It equally discussed the trend in VoIP security and Quality of Service

challenges. It concludes by reiterating the need for a cheap, reliable and affordable means of communication that

would not only maximize cost but keep abreast with the global technological change.

Keywords: Voice over Internet Protocol (VoIP), Public Switched Telephone Network (PSTN), Session Initiation

Protocol (SIP), multipoint control unit

1. Introduction

Voice over Internet Protocol (VoIP) is a technology that makes it possible for users to make telephone calls over the

internet or intranet networks. The technology does not use the traditional Public Switched Telephone Network

(PSTN); instead calls are made over an internet protocol data network. VoIP has great benefits of increased saving,

high quality voice and video streaming and several other added value services. Examples of VoIP software are:

Skype, Google talks and windows live messenger (Di Wu, 2002).

2. Overview of VoIP

VoIP stand for Voice over Internet Protocol. VoIP enables us to compress and convert voice signal to digital signal

and transmit it through Internet Protocol (IP)-enabled network like Internet, Ethernet and Wireless LAN. VoIP uses

Internet protocol to manage voice packet over Internet protocol (IP) network.

Types of VoIP Service

There are different types of VoIP based on the infrastructures employed by the owner of the network. Listed are

some popular services used in VoIP.

Computer to Computer

Computer to Computer service provides Internet telephony free using the same softphone software such as Skype,

Instant Messaging, AOL etc. It is a software-based VoIP service and both the caller and the receiver must be using

their computer in order to place calls. The following requirement must be met to use computer to computer VoIP

service: softphone software, a sound card and good Internet service. With computer to computer VoIP service, the

user may not be able to call either landline or mobile phones, and also the recipient must be online in order to call

him/her.

Computer to phone and vice versa

This is a software-based and hardware-based service. Softphone software is used to route the call to an Internet

protocol and hands off to a conventional telephone network . To use the service, one needs to subscribe and be

charged at a low rate. Examples include Skype, MSN and Google Talk that provides the service to enable their

customers to call landline from their computer. Computer to phone requirements are Internet-enabled phone and

computer, VoIP service subscription, modem and Analog Terminal Adapter to convert the call signal to digital signal

and also back to analog signal. Computer to phone does not allow emergency call users and needs to have a

computer connected to the internet.

Phone to Phone



Vol.3, No.4, 2013

19

This is a hardware-based service that allows the caller and receiver to call each other using the Internet. Many

telephone companies use this to handle long distance calls. VoIP convert the audio sound into data packets and

transfer these packets over the Internet. It allows emergence calls and does not need PSTN for initiation and

termination of calls.

2.1 VoIP system

Voice over Internet Protocol (VoIP) system is made up of End User Equipments, Network component, call

processor, Gateway and Server. The End User Equipment is the part mainly used to access the VoIP system and

communicates with other End point (Greg Tucker , 2004). End User equipments initiate and maintain the signals

needed to establish calls over the IP network. It also helps to convert voice to data packet, voice and video

communication, monitoring and network surveillance capability. They are connected to the network with cable and

maybe wireless devices. Examples of end user equipment are IP-enabled phones, multimedia computers and VoIP

enabled workstations installed with softphone . The Network Component includes routers, switches, cables, firewalls

and wireless access point. There are many existing institution’s Internet Protocol networks that will enable the

installation of our VoIP system. The network must be strong enough to support the VoIP system because the impact

of IP network is higher than the data network. Gateway is an optional component of VoIP network that helps to route

calls, handle call connection, and manage terminal and Multipoint control unit (MCU) (Mona & Nirmala, 2002). It is

responsible for providing address translation, bandwidth control, and access control and helps to improve the quality

of service and security of VoIP network. Gateway serves as an interface between public switched telephone networks

(PSTN) and VoIP network. Gateway is made up of Signalling Gateway (GS), Media Gateway (MG), Media

Controller and multipoint control unit (MCU). Signalling Gateway helps to manage signal traffic while the media

gateway manages media signal. The media gateway controller manages traffic between signalling gateway and

media gateway while multipoint control unit is the part that establishes conference calls between three or more

people for converged voice, video and data conference. It provides audio or combination of audio, video and data

conference depending on the strength of participating endpoint (Greg, 2004).

Call processor is software running on end user equipment operating system that helps in call set up, call

monitoring, user authorisation, signal coordination and bandwidth control. It translates a phone number to IP address.

Figure 1 shows the components of VoIP system.

Figure 1 Typical topology of VoIP network



Vol.3, No.4, 2013

20

The server enables the establishment of call and support for other features in the system. The Session initiation server

allows the user to forward calls to different location in the VoIP network.

2.2 VoIP Protocols and Standard

There are many protocols and standards for VoIP network (H.323, SIP, MGCP, RTSP, RSVP, SDP etc) but only the

most commonly used ones are discussed.

H.323 protocol

H.323 protocol was developed by International Telecommunication Union and Telephony (ITU-T) in 1997 based on

Real-time Transport Control protocol (RTCP) for sending voice, video and data over IP-based network (Rakesh,

2000). H.323 provides multimedia conferencing on Local Area Network (LAN) and brings together point to point

communication and multipoint conferences. It was widely adopted because it is reliable and easy to maintain. The

components include terminals, Gateway, Gatekeeper and Multipoint control unit (MCU). Terminal is the end point

that provides real-time communication for the VoIP network. Gateway is the interface between IP network and the

PSTN to another H.323 gateway. It provides Internet translation between the different terminals. Gatekeeper is the

most vital component of the H.323 protocol. It acts as the central point for all calls and provides services for end

point registrations. The functions of Gatekeeper are:

• Translate alias address to transport address

• Deny or grant access based on call authorisation, source and destination address.

• Call signalling with end point terminals

• Control the number of terminals permitted at a time in H.323 protocol (bandwidth management)

• Maintain the list of ongoing call H.323 calls to determine the busy terminals for bandwidth management.

• Rejection of call from terminal due to authorisation failure in the use of H.225 signalling (Call

authorisation).

Another important component of H.323 protocol is the multipoint control unit (MCU). It acts as a bridge that enables

two or more terminals and Gateway to participate in a multipoint conferencing. MCU is made up of Multipoint

controller (MC) and Multipoint processor. Multipoint controller determines the capabilities of the network terminal

using H.245 protocol stack but does not perform multiplexing of audio, video and data. Multipoint processor is

responsible for multiplexing of media stream . H.323 consists of a number of protocol suites. The protocol suites and

functions are listed:

• H.245 provides capabilities for channel usage, advertisement, establishment and conference control.

• H.255 for call control

• Q.931 for all signalling, call control and setup.

• Registration Admission status (RAS) is used for communicating with H.323, endpoint and gatekeeper. It

provides interaction between H.323 and the gatekeeper.

The table 1 lists the use of protocol stacks in audio, video and data packet, and their transport protocols.

Table 1: Protocol stack and transport protocols (Greg , 2004).



Vol.3, No.4, 2013

21

H.323 Call Flow

The stages in audio connection between terminal, gateway and gatekeeper in H.323 protocol are:

• Registration of terminal and Gatekeeper registration (H255-RAS).

• Call routing between the terminal and gatekeeper (H.225-RAS and H.225-Q.931).

• Initial communication and capability exchange

• Establishing audio communication (open logical channel)(H.245)

• Audio transmission (RTP/RTCP).

H.323 follows the following steps to establish connections between clients (Mona &, Nirmala, 2002). The two

endpoints will register with the gatekeeper.

• Terminal A will start Registration admission status message exchanged by initiating call to the gatekeeper.

• The information provided by gatekeeper is used by Terminal A to contact B.

• Terminal A sends a SETUP message to Terminal B

• Call proceeding message is sent by terminal B and request permission from gatekeeper.

• Terminal B sends an Alerting and connect message.

• Determination of master/slave terminal and open logical channels by Terminal A and B using H.245

message exchange.

• Establishment of Real-Time protocol (RTP) paths.

The problems of H.323 protocol are lack of flexibility, high connection setup latencies implementation difficulties.

Figure 2 and 3 shows the architecture of H.323 and the connection procedures.

Figure 2 Typical H.323 Architecture



Vol.3, No.4, 2013

22

Session Initiation Protocol (SIP)

Session Initiation Protocol (SIP) was developed by Internet Engineering Task Force (IETF) designed to initiate and

terminate VoIP session with one or more participant (Rakesh, 2000), (Mona &, Nirmala, 2002). It is an ASCII-based

peer to peer application protocol that initiates, modifies, creates and terminates interactive multimedia

communication session between users. Because of the flexibility of SIP, it is used for audio, video and data packet

transmission and communication. Session Initiation Protocol is similar to hypertext transfer protocol (http) made up

of client-server. The client sends a request to the server and the server process the request and sends back to the

client in a process called transaction. SIP is used in applications such as instant messaging, Apple chart, MSN

messenger. The use of User description protocol (SDP) for carrying out negotiation for codec identification enables

the support for user mobility by proxy and redirect server to the user’s current location.

Components of SIP

SIP consists of User Agent and Network server. User Agent is the endpoint that acts on behalf of the user and maybe

client or server. The client is called the user agent client and helps to initiate SIP request while the server known as

user agent server receives the request, process it and returns the responses on behalf of the user. Network servers

include registration server, proxy server and redirect server. Registration server is used for uploading current location

of user, proxy server receives the request forward it to the next hop while redirect server on receiving request,

determines the next hop and returns the address of the next hop server to the client instead of forwarding the request.

SIP call Flow

The six steps for establishing communication in SIP protocol are:

• User registration, initiation and location.

• Media determination.

• Determining the willingness to accept or reject calls.

• Call setup.

• Call modification and handling.

• Terminating the call (end of call).

SIP Messages

SIP defines several messages for communicating with the client and SIP server (Rakesh, 2000). Some of the

messages are listed

• INVITE- used to initiate a call by inviting user SIP session call.

Figure 3: H.323 connection and call flows (Mona &, Nirmala, 2002)



Vol.3, No.4, 2013

23

• ACK -for reliable exchange of invitation messages.

• CANCEL -to cancel a pending request by client.

• BYE- indicates termination of initiated call.

• REGISTER-provide information about user location to the SIP server.

• OPTION-used to get information about call capabilities.

• INFO-process out-of-bound information.

Figure 4 and 5 shows the architecture of SIP standard and call flow in VoIP systems.

Figure 4: Typical SIP Architecture



Vol.3, No.4, 2013

24

Figure 5 : SIP call flows (Mona& Nirmala, 2002)

Comparison of H.323 and SIP protocols

SIP and H.323 provides similar functions but exhibit different strength depending on their applications. Both SIP and

H.323 perform such functions as call set up and tear down, call control, waiting, holding and transfer, forwarding,

return, identification, Call Park and capabilities exchange. H.323 is mainly used for multimedia conferencing which

can support voice and video conferencing, white boarding, and data collaboration. Most people who use H.323

protocol claim it is complex and has overhead hence it is inefficient for VoIP system. It also lacks extensibilities and

scalability required of VoIP signalling protocol. But SIP reuses most of its header field, encoding rules, error code

and authentication mechanism of hypertext transfer protocol (HTTP). Table 2 summarises the differences between

SIP and H.323 protocols

SIP H.323

Simple to implement Very complex protocol

Use binary representation for its message Use textual representation

Not very modular Very modular

Not scalable Highly scalable

Need full backward compatibility Does not need backward compatibility

Use complex signalling Use simple signalling

Has a lot of elements Has only 37 elements

Loop detection is difficult Loop detection is easy

Large share of market Backed by IETF

Table 2 Comparison SIP of and H.323



Vol.3, No.4, 2013

25

2.3 VoIP compression Algorithms

Codec (compression –decompression) is used to convert analog signal (video, voice) to digital data or convert digital

data stream to analog signal. This helps to provide compression capability to save network bandwidth. There are

different audio codec available for voice application (Hersent, 2011). They include:

G.711: approved in 1965 and is the simplest way of digitizing analog signal. The algorithm uses Pulse Code

Modulation with less than 1% acceptable packet loss factor. The encoded audio stream of G.711 is 64kbit/s, so is

worst in terms of bandwidth but the best in quality among the entire scheme.

G.722 was approved in 1988 and provides higher quality digital coding at 7 KHz of audio spectrum at only 48, 56, or

64bits. It is mainly used for all professional conversation voice application such as video conference and IP phone

applications

G.722.1 is a wideband coder designed by Picturetel, which operate at 24bit/s or 32bit/s. It encodes a frames of 20ms

with workload of 20ms, 16kbit/s version of G.722.1 supports windows messenger.

G.723.1 was approved in 1995 for use in H.323 communication and UMTS 99 video cell phones. It uses frame

length of 30ms and needs a workload of 7.5ms in 64kbt/s or 5.3kbit/s operation modes. The algorithm is not

designed for music and its difficult to be used in a fax and modem signal transmission. The International

Telecommunication Union and Telephony recommends it for use in narrow band video conferencing and 3G

wireless multimedia devices.

G.726 was approved in 1990 and uses Adaptive differential Code modulation (ADPCM) techniques to encode G.711

bit stream in words of 2, 3, or 4 bits resulting in bit rate of 16, 24, 32 or 64kbits/s .

G.728 uses low delay, codec executed linear prediction (LD CELP) coding techniques with a mean opinion score

(MOS) similar to G.726. The algorithm is used for Fax and modem transmission, and also for H.323 video

conference.

G.729 is conjugate-structure, Algebraic Code Excited Linear Prediction (CS-ACELP) speech compression algorithm

approved by ITU-T for use in voice over frame relay application. It produce 80-bits frame encoding 10ms of speech

at a bit rate of 8kbit/s. The scheme is not designed for music and does not support Dual-Tone Multi-Frequency

(DTMF) signalling tones reliably. Listed in table 3 are properties of common voice codec schemes.

Codec Bit Rate Payload Packets per

Seconds (pps)

Quality bandwidth Sample

period

algorithm

G.711 64kbit/s 160bytes 50pps Excellent 95.2kbps 20ms PCM

G.729 8kbit/s 20bytes 50pps Good 39.2kbps 10ms CS-ACELP

G.723.1 6.3kbit/s 24bytes 34pps Good 27.2kbps 30ms MPC-MLQ

G.723.1 5.3kbit/s 20bytes 34pps Good 26.1kbps 30ms ACEP

2.4 Advantages of VoIP

There are many advantages of deploying VoIP network by companies, individuals and especially educational

institutions. Some of these advantages are:

• To save cost: VoIP system is mostly deployed in existing network thereby reducing the cost of buying

network equipments and wiring. IP network equipments are very cheap, interoperable and can be sourced

from multiple vendors compare to traditional PSTN landline equipments. Another significant reason for

deploying VoIP is because it can reduce the cost of making long distance calls. Softwares such as Skype,

Windows live messenger e.t.c allow free PC to PC calls. Calls to mobile and landline are at reduced price.

• Advanced Multimedia application: VoIP network enables multimedia applications, voice and data such as

voice/video conferencing, white boarding, file transfer to increase productivity and creates a more flexible

Table 3 Different codec scheme



Vol.3, No.4, 2013

26

communication system learning environment.

• VoIP network integrates voice and data: VoIP integrate both Voice, video and data together to save

management and operational manpower and effective use of communication links between network sites.

• Widespread availability of Internet protocol (IP): IP network is readily available all over the world, with

people having access to PC linked to internet. Furthermore, availability of gateways to/from PSTN allows

calls to use VoIP for voice and video calls (Mona & Nirmala, 2002).

• Reduce the cost of Ownership: VoIP integrates data and voice communication traffic into a single network

thereby reducing the cost of infrastructural ownership and maintenance redundancies. It brings different

network elements together such as call server, application server and client server (Bhogal et al, 2004).

• Efficient utilisation of network resource: VoIP network improves the network bandwidth efficiency and

quality of service by eliminating silence during conversation, reduce repetitive pattern in human speech and

increases inefficient data throughput.

• Greater operational flexibility: IP-based network is made up of different layers of separate components

that can be integrated to form a whole system. This allows the system, application, and services to be

dynamically managed resulting in a customised, flexible and extensible system.

2.5 Challenges Associated with VoIP Implementation

There are number of challenges hampering the implementation of VoIP network for everyday use . Because the

Internet was not designed to transfer real time data, network equipment drop most packets leading to queues that

cause jitter in packet transfer. Routing in IP network is time consuming compared to switching network. Delay and

packet loss in network affect quality of service (QoS). Efforts are on the way to reduce these challenges which

include the use of Reservation protocol (RSVP), design of high priority queues for real time traffic and the use of

multiprotocol label switching (MPLS) to speed up packets through routing points. Another problem of the Internet is

that it is not managed by a single centralised operator that can coordinate the flow of calls, but made up of different

networks and service providers which makes it difficult for providing real time traffics.

For efficient and effective real-time communication, network bandwidth is of paramount importance. A network is

made up of individual nodes and links that generate huge amount of traffic. If these nodes send more packets greater

than the network can accommodate, it can lead to network congestion which can cause QoS problems. When a

network congestion occurs, packets need to be queued leading to jitter and latency in the network . The network

should be designed to support data and real-time transmission of voice and video for better service quality.

When discussing problems of VoIP implementation, the issue of power failure and backup system are mentioned.

Traditional telephones operate on internal 48 volt internal power supply. Therefore it can still continue to work even

if there is power outage. So, they need to have backup power system using Uninterruptible power supply (UPS) and

proper power back up assessment done regularly to ensure there is sufficient power for the VoIP system.

The use of softphones software is another challenge of VoIP implementation. These softphones are vulnerable to

worms, virus, Trojan horses and spyware attack and can compromise the security of the network. Computers

connected to the Internet can be attacked if a user visits a compromised website even if he/she did not open the

website. Traditional PSTN telephone can provide emergency calls because it is tied to physical location and

emergency service provider can easily track caller’s location to the emergency dispatch office. But an individual

using VoIP network can be from anywhere around the globe, thereby making emergency call location difficult

because the caller’s location and identity can’t be traced easily. Even if the VoIP service provider can provide for

emergency calls, there is lack of standard in VoIP environment.

Most of the Wireless devices in the market today come with Wired Equivalent Privacy security algorithm. WEP has

been found to be very weak and can be cracked with free software available online. With the recent introduction of

Wi-Fi Alliance’s Wi-Fi Protected Access (WPA/WPA2), there is an improvement which can be integrated into VoIP

system. VoIP compression-decompression algorithm (codec) and gateway can be encrypted to provide improved

security to avoid the latency problem of link or network-layer encryption.

2.6 VoIP Quality of Service (QOS)

Quality of service is the ability to control and measure data transmission rate or throughput and error rate and

provides better, predictable result to selected network traffic over different underlying technologies. Voice and video



Vol.3, No.4, 2013

27

packet is intolerant to packet loss, jitter and delay unlike traditional data packet that has minimal delay in delivery of

their packets; there is no need to address Quality of Service (QoS) issues. To convey voice traffic over IP network,

there is need to ensure reliable arrival of the packets. Therefore, quality of service provides dedicated bandwidth,

controlled jitter and latency, and also improved loss characteristics. This section will discuss these Quality of Service

(QoS) parameters as they affect VoIP.

Delay: delay is the amount of time it takes to transmit data packet from source to destination. It is the end to end

delay or time delay incurred in speech by VoIP system. To ensure high quality, delay should be controlled so that

communication delay should be less than 150ms (Di Wu, 2002), (Jeomgoo, Inyong & Suh, 2010). Delay is caused

by three major factors such as codec algorithm, queue algorithm of communicating equipment and variable delay

caused by network condition at the time of transmission. It is important to minimise delay to an acceptable level of

150ms to ensure better quality of service. Codec (compression-decompression) introduces three kinds of delay:

• Processing or algorithmic delay which is the time required for codec to encode one voice frame.

• Look ahead delay, the time required for a codec to examine part of the frame

• Frame delay is the time required for sending system to transmit a single frame.

Compression algorithm affects delay, the higher the level of compression the higher the delay the system.

Packet Loss: Packet Loss is caused by hybrid circuits where it changes from 4-wire to 2-wire. It occurs when there

is packet drop in the network leading to loss. And VoIP packet is very sensitive, packet loss can greatly affect the

Quality of Service (QoS) of VoIP system. The acceptable packet loss in VoIP system is below 1%, and anything

beyond this limit is unacceptable. The major causes of packet drop are congestion in the network and buffer size,

every effort should be made to ensure the network is design to counter network congestion.

Jitter: Jitter is the variation in inter-packet arrival rate which introduce variable transmission delay over the network.

Because VoIP use User Datagram Protocol (UDP), IP network cannot guarantee the delivery time to the packets

leading to inconsistent rate of arrival. Jitter can be removed using jitter buffer, allowing an equal stream to collect a

packet and store them long enough to permit slowest arrival in correct sequence. Jitter buffer adds to the overall

delay. To support VoIP traffic reliability, the network should guarantee the following:

• Packet-forwarding latency that should be within maximum tolerable for VoIP conversation.

• Packet forwarding jitters within tolerable level to sustain a VoIP session.

• And guarantee bandwidth and capacity for VoIP session in case of network congestion.

The network should provide low latency and jitter to maintain high quality. We need to control all the mentioned

parameters to ensure high quality of VoIP service for students and staff. Sometimes we also need to prioritised

network application and limited shared network resources.

2.7 Security of VoIP

The Internet protocol (IP) used to carry traffic over packet-switched data network is vulnerable to different types of

attacks by hackers. A hacker can use sniffer or other publicly available hacking tools to modify, identify, store and

play back voice traffic transmitted over IP network. The hacker can have access to users’ call and determine the

identity of the caller. Another security breach of VoIP is eavesdropping, where a hacker can listen to the

communicating parties. Despite the facts that the end user equipment is deployed on an internal protected network,

the endpoints are not individually protected by the network firewall and maybe threatened.

Softphone software installed on the endpoint may have vulnerabilities in the operating system (OS) it is

running on. The operating system should be installed with an anti-virus software, virus detection host-based firewall

or host-based intrusion detection (Di wu, 2002). The PSTN media gateway is also vulnerable to attacks; IPSec can be

used to prevent interference with user call and to prevent unauthorised call from being set up.

Many security requirements are needed to secure VoIP service and application. There include:

• Protection of privacy of call conversation.

• Authentication of calls and end points protection from insecure of network resources.

• Ensuring of correct billing by the service provider and protection of billing information form authorised

access.

• Protections of caller behaviour or statistical information from authorised access.



Vol.3, No.4, 2013

28

• Protection of network servers and endpoints from well known threat and man in the middle attacks.

3 CONCLUSION

To keep abreast with the global technological change and maximizing cost, a reliable and cheap means of

communication is inevitable. This paper has been given a critical and succinct digest on voice over Internet protocol

(VoIP). It systematically educates one on the VoIP system, its standards, protocols and security challenges. VoIP

however is presented as a sure alternative over the Public Service Telephone Network (PSTN).

REFERENCES

1 Bhogal Amit; Hamza Idrissi; Thai-son Nguyen; Michael Wakahe (2004) “Voice over Internet Protocol”.

Online at www3.sympatico.ca/albert_nguyen/project/VoIP.pdf

2 Di Wu (2002), “ Performance studies of VoIP over Ethernet LANs”, Online at

http://www.autoresearchgateway.ac.uz/bitstream/10292/677/5/Diw/pdf. (Accessed : 28/06/2011)

3 Greg S Tucker (2004) “Voice over Internet Protocol (VoIP) and security”, Online at

www.sans.org/reading_room/whitepapers/voip/voice-internet-protocol-voip-security-1513. (Accessed:

30/08/2011)

4 Hersent Oliver (2011) “IP telephony: deploying VoIP protocol and IMS Infrastructure”, Second Edition, John

Wiley and sons, UK

5 Jeomgoo Kim, Inyong Lee, Suh ron Noh (2010) “VoIP Quality of Service Design of measurement

management process model”, International Conference on information science and applications (ICISA) Pp

1-6.

6 Mona Habib, Nirmala Bulusu (2002), “Improving QOS of VoIP over WLAN (IQ-VW)”. Online at

http://www.cs.iccs.edu (Accessed: 15/05/2011)

7 Rakesh Arora (2000) “Voice over IP: Protocol and Standards”, Online at

http://www.cse.wustl.edu/~jain/cis788-99/ftp/voip_protocols.pdf (Accessed; 29/05/2011)

This academic article was published by The International Institute for Science,

Technology and Education (IISTE). The IISTE is a pioneer in the Open Access

Publishing service based in the U.S. and Europe. The aim of the institute is

Accelerating Global Knowledge Sharing.

More information about the publisher can be found in the IISTE’s homepage:

http://www.iiste.org

CALL FOR PAPERS

The IISTE is currently hosting more than 30 peer-reviewed academic journals and

collaborating with academic institutions around the world. There’s no deadline for

submission. Prospective authors of IISTE journals can find the submission

instruction on the following page: http://www.iiste.org/Journals/

The IISTE editorial team promises to the review and publish all the qualified

submissions in a fast manner. All the journals articles are available online to the

readers all over the world without financial, legal, or technical barriers other than

those inseparable from gaining access to the internet itself. Printed version of the

journals is also available upon request of readers and authors.

IISTE Knowledge Sharing Partners

EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open

Archives Harvester, Bielefeld Academic Search Engine, Elektronische

Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial

Library , NewJour, Google Scholar

http://www.iiste.org/

http://www.iiste.org/Journals/

voice over internet protocol (voip)

Documents

overview of voip voip

internet protocol voip

computer voip service

voip security

advantages of voip

voip implementation

voip system

computer computer