user guide - sic.co.th app user guide.pdf · figure 13 ndef message ... 4.2 writer transponder...

User Guide

SIC43NT APP User Guide

The information herein is for product information purpose. While the contents in this publication has been carefully

checked; no responsibility, however, is assumed for inaccuracies. Silicon Craft Technology Co., Ltd. reserves the right to

make changes to the products contained in this publication in order to improve design, performance or reliability.

This document descripts how to use SIC43NT Writer Android Application with SIC43NT

IC. This manual consists of how to install, how to read tag and how to write tag.

Revision History

Revision Date Software Version

Description/Change/Updated/Comment Product

Code

1.0 June 2017 1.0.0 1st Release SIC43NT

1.1 July 2017 1.1.0 Adding duplicate function

Rev 1.1– July 2017

Copyright © 2017 Silicon Craft Technology


SIC43NT User Guide

of 22

Contents

1. Introduction............................................................................................................... 5

2. Instruments and Specification .................................................................................... 5

3. Installation ................................................................................................................ 5

3.1 Manual Installation ....................................................................................................... 5

4. Demonstration Application ........................................................................................ 9

4.1 Read Information ........................................................................................................ 10

4.1.1 Configuration .................................................................................................................................. 11

4.1.2 Data Memory .................................................................................................................................. 12

4.1.3 NDEF message ................................................................................................................................ 13

4.1.4 Tamper Status ................................................................................................................................. 13

4.2 Writer Transponder ..................................................................................................... 15

4.2.1 Clear Password................................................................................................................................ 15

4.2.2 Password Setting ............................................................................................................................ 16

4.2.3 RFD Pin ............................................................................................................................................ 17

4.2.4 Rolling Code Mode .......................................................................................................................... 18

4.2.5 NDEF message ................................................................................................................................ 19

4.2.6 Configure State ............................................................................................................................... 21

Rev 1.1– July 2017



SIC43NT User Guide

of 22

List of Figures

Figure 1 SIC folder ................................................................................................................................... 5

Figure 2 SIC43NT Configure 20170515.apk file ...................................................................................... 6

Figure 3 SIC folder in smartphone .......................................................................................................... 6

Figure 4 Click file to install ...................................................................................................................... 7

Figure 5 Unknown Sources pop-up ......................................................................................................... 7

Figure 6 Installing .................................................................................................................................... 8

Figure 7 SIC43NT Application .................................................................................................................. 9

Figure 8 Please Tap a Tag ...................................................................................................................... 10

Figure 9 Tdata and Authentication ....................................................................................................... 11

Figure 10 RF Detect Pin ......................................................................................................................... 11

Figure 11 Dynamic Pointer and Dynamic Data ..................................................................................... 12

Figure 12 Data Memory ........................................................................................................................ 12

Figure 13 NDEF Message....................................................................................................................... 13

Figure 14 Tamper Status ....................................................................................................................... 13

Figure 15 Tamper Status Fail ................................................................................................................. 14

Figure 16 Pop-up for checking protection ............................................................................................ 15

Figure 17 Clear Password ...................................................................................................................... 15

Figure 18 Password Setting ................................................................................................................... 16

Figure 19 RF Detection .......................................................................................................................... 17

Figure 20 Tamper Detection Mode ....................................................................................................... 17

Figure 21 Rolling Code Mode ................................................................................................................ 18

Figure 22 Rolling Code Key and IV ........................................................................................................ 18

Figure 23 NDEF Information ................................................................................................................. 19

Figure 24 Write on SIC43NT tag ............................................................................................................ 21

Figure 25 Setting Respond .................................................................................................................... 21

Rev 1.1– July 2017



SIC43NT User Guide

of 22

List of Tables

Table 4-1 Tamper Status ....................................................................................................................... 11

Table 4-2 RF Detection Mode ............................................................................................................... 17

Table 4-3 Tamper Detection Mode ....................................................................................................... 17

Table 4-4 NDEF Type ............................................................................................................................. 19

Rev 1.1– July 2017



SIC43NT User Guide

of 22

1. Introduction This document descripts about how to install and how to use SIC43NT configure

application on Android.

2. Instruments and Specification To use this application, user has the instruments that have specification below:

1. Smart Phone : Android SPI Level 16(Jelly Bean)

2. SIC43NT Demo : Rev C

3. Installation

3.1 Manual Installation 1. Connect smartphone to computer and enter to SIC folder as show in Figure 1.

Figure 1 SIC folder

Rev 1.1– July 2017



SIC43NT User Guide

of 22

2. Copy .apk file to SIC folder

Figure 2 SIC43NT Configure 20170515.apk file

3. Open SIC folder in the smartphone and find .apk file.

Figure 3 SIC folder in smartphone

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4. Click .apk file to install

Figure 4 Click file to install

Setting notification for unknown sources, please enable “Allow installation of apps from

source other than a Play Store”.

Figure 5 Unknown Sources pop-up

Rev 1.1– July 2017



SIC43NT User Guide

of 22

5. Wait until installation is finished.

Figure 6 Installing

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4. Demonstration Application This part demonstrates about how to use SIC43NT Demo with SIC43NT

Application both of read information and configure transponder. This application is

developed by using Android Studio version 2.3.2.

Figure 7 SIC43NT Application

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.1 Read Information Click “Read” button to read tag information and tab a tag to the phone.

Figure 8 Please Tap a Tag

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.1.1 Configuration Show configured in SIC43NT consists of Tdata, Authentication, RFD Pin configured,

Dynamic, Pointer, Dynamic Data Configured.

Tdata is Tamper Status

Table 4-1 Tamper Status

Ascii data Description

00 Untampered

Others Tampered

Figure 10 RF Detect Pin

Triggering Mode of RFD pin

RFD Pin function

Is data auto program to EEPROM?

Tampering Check Evident

Tamper Bias Current check

Figure 9 Tdata and Authentication

Rev 1.1– July 2017



SIC43NT User Guide

of 22

Figure 11 Dynamic Pointer and Dynamic Data

4.1.2 Data Memory

Show start address of Dynamic NDEF message

Rolling Code Mode

Dynamic NDEF message consists of

UID, Tamper and RLC

Figure 12 Data Memory

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.1.3 NDEF message

Figure 13 NDEF Message

4.1.4 Tamper Status Tampering Status of transponder is shown in Figure 13(a)-(b).

Figure 14 Tamper Status

(a) (b)

NDEF message in transponder

Transponder’s UID

Tamper Status of transponder

“00” is Untampered, others is tampered

Rolling Code in transponder

Rev 1.1– July 2017



SIC43NT User Guide

of 22

If the information isn’t complete, please tap a tag again.

Figure 15 Tamper Status Fail

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2 Writer Transponder Click “Write” button to configure the tag. Figure 16 show warning when you

write the tag must ensure that tag doesn’t have password protection.

Figure 16 Pop-up for checking protection

4.2.1 Clear Password Clear Password by entering current password to the tag and it will be disable

automatically.

Figure 17 Clear Password

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.2 Password Setting Password setting is for protection data in SIC43NT cannot be changed by

other person.

Figure 18 Password Setting

Password 4 Bytes data

Password ACK The respond when SIC43NT receive a matched password

Protected Address Start protected area

Authenticate Limitation Limitation of negative password

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.3 RFD Pin Resonant Frequency Detection Pin can be set in to 2 modes: RF Detection

mode and Tamper Detection mode.

Table 4-2 RF Detection Mode

Figure 19 RF Detection

Table 4-3 Tamper Detection Mode

Figure 20 Tamper Detection Mode

RF Detection Mode RF detection Items Description

Trigger Event No Field Detect No RF field present

1st SOF First Start of Frame

Select Select state

Field Present RF field present

Sleep Mode Disable None sleep

Enable Sleep Enable

Detect Mode Manual Manual Configuration Pin behavior define from Output Type

Auto Auto Detect

Output Type Mode Open Drain Pull low when RF field is detected

Push Pull Logic high when RF field is detected

Tamper Detection Mode TP detection Items Description

Tamper Flag - HEX data for Tamper status

Tamper Bias Current 6.4 uA

Current detect tamper status

3.2 uA

1.6 uA

0.8 uA

Check Tamper Mode Continue Always check tamper pin

Power up Check only power up

Auto Programing Tamper Disable Doesn’t program status to EEPROM

Enable Program status to EEPROM

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.4 Rolling Code Mode Configure rolling code mode to control Dynamic NDEF Message.

Figure 21 Rolling Code Mode

Set the rolling code key and initial vector for time stamp. When the rolling code key of tag is

changed it has to be changed on the server side too.

Figure 22 Rolling Code Key and IV

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.5 NDEF message Configure NDEF

message and select Dynamic

data.

Figure 23 NDEF Information

Table 4-4 NDEF Type

NDEF Type Description

URI/URL Open URL via default browser

Plaintext Record containing UTF-8 text data.

Application Use Package name to Open Application.

Bluetooth connection Pairing device via Bluetooth by using MAC address

Custom record Customize NDEF message

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.6 Other Clone Tags is cloning all data from a tag to the others.

Figure 24 Clone Tags

Firstly, click “CLONE” button and then tab a tag to read all information. Next, tab the target

tag to write all data to tag. It can be cloned many tags by re-tab others.

Figure 25 Steps to clone tag

(1) (2) (3)

Rev 1.1– July 2017



SIC43NT User Guide

of 22

4.2.7 Configure State Click “Configure” to set transponder and then tab a transponder.

Figure 26 Write on SIC43NT tag

After setting transponder, it will show SUCCESS. If it FAILS please tap a transponder again.

Figure 27 Setting Respond

Rev 1.1– July 2017



SIC43NT User Guide

of 22

user guide - sic.co.th app user guide.pdf · figure 13 ndef message ... 4.2 writer transponder...

Documents