ts controls signal & lighting controls controls signal & lighting controls email:...

TS CONTROLS Signal & Lighting Controls www.tscontrolsonline.com Email: [email protected]

RS10/RS12 of 27 Release Date - 160131

Thank you for purchasing a RS / TS series traffic light control. By design, all controls are built for ease of use and years of trouble free operation and enjoyment. Manufactured in the USA, all controls are inspected and tested prior to shipment for reliability. Please refer to the following information on your RS / TS series control. What’s included: (Control Only) 1x - RS / TS Series Control 4x - Adhesive Mounting Posts Components included as a “Kit”: (Optional) 1x - Power Cord^ - (May vary slightly by color and/or length) 1x - Hook-up Wire w/ Fork Ends* * RS12 / TS12 Series Include 2x - Hook-up Wire w/ Fork Ends. ^ Power Cord Included with TS14 Series.

TABLE OF CONTENTS Page

1. General Specifications………………………………...............................................................2 2. Installation & Safety Tips…………………….…………........................................................3-6 3. RS10 Control Switch Settings…........…………………........................................................7-9 4. RS10 - Single Signal Applications……………………………..………...............................10-14 5. RS12 Control Switch Settings………....…………………..………………………...............15-18 6. RS12 - Multi-Signal Applications……….………..……….........................…....…..............19-26 7. Warranty Information & Return Form….…………………………….......................................27



GENERAL SPECIFICATIONS (**)

Dimensions: Circuit Board Size RS10 Series - 2.75" x 3.25" (2.25" x 2.75" screw mounting) RS12 Series - 2.75" x 4.75" (2.25" x 4.25" screw mounting) AC Power: 120VAC - Fused (220VAC Optional - available by request) Fuse: RS10/12 Series - 5x20mm 250V/3A Nominal (5A Maximum) Wire Size: 16 - 22 AWG - Recommended. Output Power: RS10/RS12 - 120VAC / 150W Nominal - Each Channel (^) Time Delay: See control switch settings. Time Adjustment:* Counter-Clockwise = Slow Clockwise = Fast *Note: Time adjustment is single turn, similar to radio volume knob. Do not force beyond stopping points, as this will cause permanent damage. ^Note: Output power is compatible with both L.E.D. and incandescent lighting. **Note: General specifications are subject to change without notice.



INSTALLATION & SAFETY TIPS 1. Warning! - Never handle control unit while powered on. 2. Not intended for damp, or wet environments. 3. Only replace fuse with equivalent size and rating. 4. Remove power for bulb replacement and/or servicing of any type. 5. Do not overload outputs beyond maximum rated specification. 6. When connecting more than one incandescent bulb to a single output, divide the desired bulb wattage by 150 Watts. The result will be the number of bulbs of the desired wattage that can be used on a single output. Example: How many 40 Watt bulbs can I connect to a single output rated at 150 Watts? 150 Watts / 40 Watts = 3.75 ~ 3x - 40 Watt bulbs The number of 40 Watt bulbs that can be connected to a single output without overload is 3. 7. For AC power connection, follow the wiring diagram below.

Caution!: If you need assistance, please consult a qualified electrician.



8. If your signal is equipped with a screw-terminal block, you may reference the following diagram.


9. If your signal is not equipped with a screw-terminal block, you may reference the following diagram(s).



CONTROL MOUNTING

1. Before mounting, be sure mounting surface area is smooth, clean, dry, & oil free. 2. Be sure mounting location allows enough clearance area around the control unit, where metal components will not come into contact with the bottom, or components on the top side of the control unit. 3. Do not route wiring underneath control unit.

RIGHT / CORRECT !!!


WRONG / INCORRECT !!!



RS10 CONTROL SWITCH SETTINGS

Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON.

TIME DELAY

R/C Y/B G/A

(RED) (YEL) (GRN)

Time delay range: (approximate) RED - 10 seconds - 5 minutes YEL - 3 seconds - 30 seconds GRN - 10 seconds - 5 minutes

Pushbutton Input Connection:

S3 / -C and/or S4 / -C

WARNING! DO NOT USE, OR CONNECT (+AX) TERMINAL UNLESS SPECIFIED. IMPROPER CONNECTIONS MAY DAMAGE CONTROL UNIT.

Mode 1: Standard Traffic Light Sequence

(Default)

Mode 2: Vintage Light

Sequence Old Timey

Mode 3: British Traffic Light

Sequence Plessey Tin Lantern

Mode 4: Green-Yellow-Red

W.S. Darley C-811

OR


W.S. Darley D-480

Note: Reduced bulb wattage may be required when using “Overlap” functions / settings.



RS10 CONTROL SWITCH SETTINGS (Continued)


Mode 6 - 8: Optional Crosswalk Push button Input

Normally Open (N.O.) - Dry contact pushbutton input (S4) cycle to "Walk" during Red / Don't Walk cycle.

Mode 6 - 8: Adjustments &

Settings

TIME DELAY Adjustment for flash count (fixed value):

Minimum - 10X Flash Count Mid Point - 20X Flash Count

R/C G/C Maximum - 30X Flash Count (DWK) (WLK)

Mode 6: Pedestrian / Crosswalk

Don't Walk-Flash

Mode 7: Pedestrian / Crosswalk Walk-Flash

Mode 8: Pedestrian / Crosswalk w/o Flash

OR

Mode 9: Flashing Red

(1/2 second - Fixed)

Mode 10: Flashing Yellow

(1/2 second - Fixed)






Mode 11: Wig-Wag

Red / Yellow (1/2 second - Fixed)

Mode 12: Chasing

Sequence

Time delay range: (approximate) RED - .25 seconds - 10 seconds YEL - .25 seconds - 10 seconds GRN - .25 seconds - 10 seconds

Mode 13: Chasing

Sequence

Time delay range: (approximate) RED - 2.5 seconds - 1 minute : 30 seconds YEL - 2.5 seconds - 1 minute : 30 seconds GRN - 2.5 seconds - 1 minute : 30 seconds

Mode 14: Chasing

Sequence

Time delay range: (approximate) RED - 5 seconds - 8 minutes YEL - 5 seconds - 8 minutes GRN - 5 seconds - 8 minutes

Mode 15: Chasing

Sequence

Time delay range: (approximate) RED - 10 seconds - 16 minutes YEL - 10 seconds - 16 minutes GRN - 10 seconds - 16 minutes

Mode 16: Red / Yellow

Flashing RxR / Caution /

School Zone

For signal applications shown.

Mode 16: Adjustments &

Settings

TIME DELAY Toggle / wig-wag speed (0.25s - 1.5s) G/A (GRN) R/C (RED) / Y/B (YEL) On / Off

R/C Y/B G/A




Application: RS10 - G,Y,R Signal / Chasing sequence





Application: RS10 - PED / Crosswalk Signal





Application: RS10 - School Zone / Caution Signaling





Application: RS10 - RxR Signal *RxR Signal must be compatible or converted with 120VAC lighting





Application: RS10 Simple Racing Tree





RS12 CONTROL SWITCH SETTINGS


Signal #1

Time Delay

Signal #2

Time Delay

Time delay range: 10 seconds - 5 minutes (approximate) Signal #1 - adjusts signal #1 green (signal #2 - red) Signal #2 - adjusts signal #2 green (signal #1 - red)




Mode 1: Standard Traffic Light Sequence

(Default)

Mode 2: Vintage Light

Sequence Old Timey

Mode 3: British Traffic Light

Sequence Plessey Tin Lantern


W.S. Darley C-811


W.S. Darley D-480







w/ Arrows Doghouse

Mode 7: Red / Yellow Flashing

RxR / Caution / School Zone

For signal applications shown.

Mode 7: Adjustments &

Settings

Adjust Adjust toggle / on/off A1 wig-wag speed output. (0.25s - 1.5s).

Mode 8: Chasing

Sequence

Time delay range: 0.25 - 5.0 seconds

Mode 9 - 10: Adjustments &

Settings

Green/Red

(Walk / Don't Walk) Time Delay

Adjustment for flash count (fixed value): Minimum - 10X Flash Count Mid Point - 20X Flash Count Maximum - 30X Flash Count

Mode 9 - 14: Crosswalk

Push button Input Adjustments &

Settings

Normally Open (N.O.) - Dry contact pushbutton input (S4) cycle toward "Walk" during Red / Don't Walk cycle.










+ Crosswalk Walk on Green

Don't Walk-Flash


+ Crosswalk Walk on Green

Walk-Flash


+ Crosswalk Walk on Red

15x Don't Walk-Flash


+ Crosswalk Walk on Red


Mode 13: 2x Crosswalk







Mode 14: 2x Crosswalk





Mode 15: Racing Tree

Sport Sequence (S3 Input)

Sport sequence via S3 input. Normally Open (.N.O.) - Dry contact.


Pro Sequence (S4 Input)

Pro sequence via S4 input. Normally Open (.N.O.) - Dry contact.


Demo

Automatic sequencing of sport, and pro racing tree sequences including a quick light scan, with a pre-stage sequence between each of the three sequences.




Application: RS12 - Dual G,Y,R Signals / 2-Way Signaling, or G,Y,R & Arrow(s)





Application: RS12 - Quad G,Y,R Signals / 4-Way Signaling.





Application: RS12 - School Zone / Caution Signaling





Application: RS12 - RxR Signal *RxR Signal must be compatible or converted with 120VAC lighting





Application: RS12 Single G,Y,R Signal w/ Crosswalk - Walk on Green





Application: RS12 Single G,Y,R Signal w/ Crosswalk - Walk on Red





Application: RS12 Dual PED / Crosswalk Signals, 2/4 Way Signaling.





Application: RS12 Racing Tree





WARRANTY / RETURN FORM

MODEL: ____ RS/TS 10 ____ RS/TS 12 TS14 OTHER PURCHASE DATE: ___________ (Please Specify Model)

1 YEAR - LIMITED WARRANTY

All TS series are warranted against manufacturing/workmanship defects for a period of 1 year from

date of purchase. Any TS series control that is used for other than the purpose intended, resulting in

damage, personal or property, is the rightful owners responsibility. This warranty does not cover, improper

installation /application, modification, misuse, abuse, power surge, brown outs, lightning strikes, and any

other “act of god” resulting in damage, whether personal or property. TS series controls are designed for

indoor and private use only. And, are not intended for industrial / commercial, or municipality use.

Return Policy:

TS Series controls returned for refund, or repair, without proof of purchase will not be honored under

warranty. TS series controls under warranty will be repaired/replaced, at the discretion of the

manufacturer, as necessary. Any TS series control returned for repair after warranty period, “out of

warranty” will be repaired at a flat rate cost of $20, and will be warranted for a period of 30 days.

Mail / Remit to: Brent Anderson

2725 Castleton Ave.

Toledo, OH 43613

Email: [email protected]

Directions: Complete the requested information below.

Name: __________________________________________________________

Address: ________________________________________________________

City-State-Zip: ___________________________________________________

Phone#: (_______)________________________________________________

E-mail (optional): ________________________________________________

(Please Check)

Reason for return / description of failure / problem. Repair / Exchange Refund (See Return Pol icy)

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

ts controls signal & lighting controls controls signal & lighting controls email:...

Documents