SECTION 260100 - BASIC ELECTRICAL SCOPE OF WORK REQUIREMENTS:A. ALL WORK SHALL BE IN COMPLIANCE WITH THE LATEST APPLICABLE CODES, LAWS AND ORDINANCES AND THE

NATIONAL ELECTRICAL CODE. PROVIDE AND FURNISH ALL LABOR, MATERIALS, PERMITS AND INCIDENTALS REQUIREDTO COMPLETE ALL WORK AS SHOWN ON CONTRACT DOCUMENTS.

B. DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL SCOPE AND ARRANGEMENT OF THE ELECTRICALINSTALLATION AND ARE NOT INTENDED TO SHOW EVERY CONNECTION, CONDUIT OR EXACT LOCATION AND EXTENTOF WORK. CONTRACTOR SHALL INSTALL THE WORK COMPLETE, INCLUDING DETAILS AND EQUIPMENT NECESSARY TOPERFORM THE FUNCTION INDICATED ON THE DRAWINGS. SUBMIT SHOP DRAWINGS FOR ALL ELECTRICAL EQUIPMENT

ASSOCIATED WITH THE PROJECT UNDER ONE SUBMITTAL. SEPARATE SUBMITTALS MAY BE REJECTED. SUBMITDIMENSIONED ELECTRICAL ROOM LAYOUTS TO 1/4” SCALE WITH MANUFACTURES EQUIPMENT LOCATIONS SHOWNTHEREIN.

C. ALL MATERIALS SHALL BE NEW AND FREE OF DEFECTS, AND SHALL BE U.L. LISTED OR BE LISTED WITH AN APPROVED,NATIONALLY RECOGNIZED ELECTRICAL TESTING AGENCY.

D. CONTRACTOR SHALL INSPECT ALL NEW MATERIAL AND EQUIPMENT PRIOR TO INSTALLATIONS FOR DAMAGES, ANDSHALL VERIFY EQUIPMENT OPERATES SATISFACTORILY.

E. CONTRACTOR SHALL WARRANT ALL MATERIAL AND EQUIPMENT FURNISHED TO COMPLETE ALL WORK FOR ONE YEARAFTER FINAL ACCEPTANCE OF COMPLETION. MATERIALS AND EQUIPMENT DEFECTS OF FAILURES DUE TO ABUSE, ORWORKMANSHIP NEGLECT SHALL BE MADE GOOD BY THE CONTRACTOR WITHOUT COST TO THE OWNER.

F. PROVIDE ONLY NEW, STANDARD UNDERWRITER'S LABORATORY INC. LISTED FIRST-GRADE MATERIALS THROUGHOUT,AND SHALL BE MARKED WITH UNDERWRITER'S LABORATORY INC. LISTED AND WITH MANUFACTURER'S BRAND ORTRADEMARK. ALL MATERIALS SHALL BE OF ONE MANUFACTURER.

G. CONTRACTOR SHALL BE EXPERIENCED IN THEIR TRADE. CONTRACTOR'S WORK SHALL PRESENT A NEAT APPEARANCEUPON COMPLETION. MATERIALS AND EQUIPMENT INSTALLED SHALL BE PLUMB, STRAIGHT, AND LEVEL.

H. CONTRACTOR SHALL COORDINATE WITH THE ARCHITECT AND OWNER ON EXACT LOCATION OF WIRING DEVICES ANDRACEWAYS FOR OWNER-FURNISHED EQUIPMENT PRIOR TO ROUGH-IN. COORDINATE ELECTRICAL EQUIPMENT ANDMATERIALS INSTALLATION WITH OTHER BUILDING COMPONENTS AND TRADES. REVIEW AND COORDINATE BETWEENALL CONSTRUCTION DOCUMENTS AND PROJECT SPECIFICATIONS.

I. COORDINATE THE INSTALLATION OF REQUIRED SUPPORTING DEVICES AND SLEEVES TO BE SET IN POURED IN PLACECONCRETE AND OTHER STRUCTURAL COMPONENTS, AS THEY ARE CONSTRUCTED. COORDINATE THE CUTTING ANDPATCHING OF BUILDING COMPONENTS TO ACCOMMODATE THE INSTALLATION OF ELECTRICAL EQUIPMENT ANDMATERIALS IN RENOVATION PROJECTS.

J. COORDINATE CONNECTION OF ELECTRICAL SYSTEMS AND EQUIPMENT REQUIREMENTS WITH LOCAL UTILITYSERVICES TO PROVIDE AND COMPLY WITH THE REQUIREMENTS FOR EACH SERVICE.

K. UPON COMPLETION OF WORK, THE CONTRACTOR SHALL TEST ALL WIRING AND EQUIPMENT INSTALLATION, AND SHALLBE IN PERFECT WORKING CONDITION IN ACCORDANCE WITH THE INTENT OF THE CONTRACT DOCUMENTS. MARKDRAWINGS TO INDICATE ACTUAL FIELD CONDITIONS.

L. THE WORD “PROVIDE” MEANS FOR THE CONTRACTOR TO FURNISH AND INSTALL.

260519 CONDUCTORS AND CABLES:A. WIRING GENERAL: CONDUCTORS SHALL BE COPPER AND HAVE CURRENT CARRYING CAPACITIES AS PER N.E.C., WITH

600 VOLT INSULATION, AND COMPLY WITH NEMA WC 70. ALUMINUM CONDUCTORS ARE NOT APPROVED.CONDUCTORS SHALL BE #12 MINIMUM, EXCEPT FOR CONTROLS AND FIXTURE WIRE. SOLID FOR #10 AND SMALLERCONDUCTORS, STRANDED FOR #8 AND LARGER.

B. FEEDERS, BRANCH CIRCUITS, CLASS 1 AND CLASS 2 CIRCUITS SHALL BE INSULATION TYPE XHHW OR THWN.C. MAINTAIN STANDARD COLOR CODING OF BLACK, RED, AND BLUE FOR 120/208 VOLT 3-PHASE WIRING AND BROWN,

ORANGE AND YELLOW FOR 277/480 VOLT 3-PHASE WIRING. COLOR CODING SHALL MATCH EXISTING FACILITIES WHERETHE COLOR CODING IS NOT STANDARD. WHITE NEUTRAL AND GREEN GROUND.

D. CONCEAL CABLES IN FINISHED WALLS, CEILINGS, AND FLOORS, UNLESS OTHERWISE INDICATED. INSTALL EXPOSEDCABLES PARALLEL AND PERPENDICULAR TO SURFACES OF EXPOSED STRUCTURAL MEMBERS, AND FOLLOW SURFACECONTOURS WHERE POSSIBLE.

E. MAKE SPLICES AND TAPS THAT ARE COMPATIBLE WITH CONDUCTOR MATERIAL AND THAT POSSESS EQUIVALENT ORBETTER MECHANICAL STRENGTH AND INSULATION RATINGS THAN UNSPLICED CONDUCTORS. SERVICE ENTRANCEAND PANEL FEEDERS SHALL NOT BE SPLICED. TIGHTEN ELECTRICAL CONNECTORS AND TERMINALS ACCORDING TOMANUFACTURER'S PUBLISHED TORQUE-TIGHTENING VALUES. IF MANUFACTURER'S TORQUE VALUES ARE NOT

INDICATED, USE THOSE SPECIFIED IN UL 486A AND UL 486B.F. WIRING AT OUTLETS: INSTALL CONDUCTOR AT EACH OUTLET, WITH AT LEAST 12 INCHES OF SLACK. WIRING IN LIGHT

POLES HANDHOLES: PROVIDE AT LEAST 18” OF SLACK AT HANDHOLE.

260526 GROUNDING AND BONDING:A. GROUNDING SHALL BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND LOCAL CODES AND

REQUIREMENTS.B. FEEDERS AND BRANCH CIRCUITS SHALL HAVE INSTALLED IN THE SAME RACEWAY AS THE CIRCUIT CONDUCTORS, AN

INSULATED COPPER GROUNDING CONDUCTOR SIZED IN ACCORDANCE WITH NEC.C. DESCRIPTION OF SYSTEM: IN GENERAL, ALL ELECTRICAL EQUIPMENT (METALLIC CONDUIT, MOTOR FRAMES, PANEL

BOARDS, ETC.) SHALL BE BONDED TOGETHER WITH A GREEN INSULATED OR BARE COPPER SYSTEM GROUNDINGCONDUCTOR IN ACCORDANCE WITH SPECIFIC RULES OF ARTICLE 250 OF THE N.E.C. EQUIPMENT GROUNDINGCONDUCTORS THROUGH THE RACEWAY SYSTEM SHALL BE CONTINUOUS FROM MAIN SWITCH GROUND BUS TOPANEL GROUND BAR OF EACH PANEL BOARD, AND FROM PANEL GROUNDING BAR OF EACH PANEL BOARD TO BRANCH

CIRCUIT EQUIPMENT AND DEVICES. CONNECTORS LISTED AND LABELED BY A NATIONALLY RECOGNIZEDTESTING LABORATORY ACCEPTABLE TO AUTHORITIES HAVING JURISDICTION FOR APPLICATIONS IN WHICH USED, ANDFOR SPECIFIC TYPES, SIZES, AND COMBINATIONS OF CONDUCTORS AND OTHER ITEMS CONNECTED. ALL FEEDERMETALLIC CONDUITS AND FLEXIBLE METAL CONDUITS CONNECTIONS TO PANEL CABINETS, EQUIPMENT CABINETS,TRANSFORMER ENCLOSURES, ETC. SHALL BE PROVIDED WITH GROUNDING BUSHINGS.

D. ELECTRICAL ROOM GROUND BUS BARS: NEWTON INSTRUMENT COMPANY INSULATED GROUND BAR, MINIMUM SIZE ¼”X 4” X 10”, COPPER, MANUFACTURER PRE-DRILLED HOLES. ALL GROUND BUS BARS SHALL BE BONDED TO MAINELECTRICAL GROUND BUS BAR WITH MINIMUM 3/0 COPPER GROUND, OR SIZED PER CODE, FOR A CONTINUOUSCOPPER GROUNDING SYSTEM. UTILIZING BUILDING STEEL OR FOOTING IS NOT ACCEPTABLE. TELECOMMUNICATIONS,IDF, DATA, COMPUTER, AND SIMILAR ROOMS: NEWTON INSTRUMENT COMPANY INSULATED GROUND BAR, ¼” X 4” X 20”,COPPER, MANUFACTURER PRE-DRILLED HOLES. BOND GROUND BUS BAR TO MAIN ELECTRICAL GROUND BUS BARWITH MINIMUM 3/0 AWG COPPER.

E. GROUND RODS: COPPER-CLAD STEEL, SECTIONAL TYPE; 3/4 INCH IN DIAMETER, BY 10 FEET. PROVIDE ADDITIONALLENGTHS IN 10' SECTIONS TO ACHIEVE SPECIFIED MINIMUM RESISTANCE TO GROUND, MEASURED IN OHMS, ATBUILDING SERVICES GROUNDING SYSTEMS. EXOTHERMIC CADWELD SHALL BE USED FOR BUILDING GROUNDINGSYSTEM CONNECTION TO DRIVEN GROUND RODS AND CONNECTION TO LIGHTNING PROTECTION DRIVEN GROUNDRODS.

F. GROUNDING AND BONDING FOR PIPING: METAL WATER SERVICE PIPE: INSTALL INSULATED COPPER GROUNDINGCONDUCTORS, IN CONDUIT, FROM BUILDING'S MAIN SERVICE EQUIPMENT, OR GROUNDING BUS, TO MAIN METALWATER SERVICE ENTRANCES TO BUILDING. BOND EACH ABOVE GROUND PORTION OF GAS PIPING SYSTEMDOWNSTREAM FROM EQUIPMENT SHUTOFF VALVE. CONCRETE ENCASED ELECTRODE IN BUILDING FOOTER SHALL BEA BARE CONDUCTOR, SAME SIZE AS THE BUILDING SYSTEMS GROUNDING CONDUCTOR, ROUTED MINIMUM 20' AND TIE

WIRED TO THE REINFORCING BARS.G. PERFORM GROUNDING TEST: PERFORM TESTS BY FALL-OF-POTENTIAL METHOD ACCORDING TO IEEE 81, USING

MEGOHMETER. REPORT MEASURED GROUND RESISTANCES THAT EXCEED 5 OHMS. EXCESSIVE GROUNDRESISTANCE: IF RESISTANCE TO GROUND EXCEEDS 5 OHMS, PROVIDE ADDITIONAL DRIVEN GROUNDING RODS UNTILTHE MEASURED GROUND RESISTANCE DOES NOT EXCEED 5 OHMS.

ED STEEL. MOUNTING APPARATUS FOR EXTERIOR APPLICATIONS SHALL BE STAINLESS STEEL. EXTERIOR LOCATEDSUPPORT APPARATUS SHALL CONSIST OF DIRECT BURIAL CONCRETE POSTS, STAINLESS STEEL OR ALUMINUM CHANNEL,

AND STAINLESS STEEL SPRINGS, BOLTS, WASHERS, ETC.H. MULTIPLE RACEWAYS OR CABLES SHALL HAVE L TRAPEZE-TYPE SUPPORTS FABRICATED WITH STEEL SLOTTED OR

OTHER SUPPORT SYSTEM, SIZED SO CAPACITY CAN BE INCREASED BY AT LEAST 25 PERCENT IN FUTURE WITHOUTEXCEEDING SPECIFIED DESIGN LOAD LIMITS. SECURE RACEWAYS AND CABLES TO THESE SUPPORTS WITHTWO-BOLT CONDUIT CLAMPS USING SPRING FRICTION ACTION FOR RETENTION IN SUPPORT CHANNEL. SPRING-STEELCLAMPS DESIGNED FOR SUPPORTING SINGLE CONDUITS WITHOUT BOLTS MAY BE USED FOR 1-1/2-INCH AND SMALLERRACEWAYS SERVING BRANCH CIRCUITS AND COMMUNICATION SYSTEMS ABOVE SUSPENDED CEILINGS.

I. SUPPORTING RACEWAYS VIA OTHER RACEWAYS CABLE TRAYS AND WIREWAYS ARE NOT APPROVED.

260533 RACEWAYS AND BOXES:A. LISTING AND LABELING: METAL CONDUITS AND NONMETALLIC CONDUITS, TUBING, AND FITTINGS SHALL BE LISTED AND

LABELED AS DEFINED IN NFPA 70 AND MARKED FOR INTENDED LOCATION AND APPLICATION.B. CONDUIT GENERAL: RIGID SHALL BE MINIMUM 1", GALVANIZED OUTSIDE AND INSIDE BY HOT DIPPING, E.M.T. SHALL BE

MINIMUM 3/4" AND SHALL BE ELECTRO-GALVANIZED. CONDUITS SHALL BE AS MANUFACTURED BY ALLIED, PITTSBURGHSTANDARD, REPUBLIC, THOMAS & BETTS, TRIANGLE, WHEATLAND OR YOUNGSTOWN.

C. PROVIDE END BUSHINGS ON ALL CONDUITS. PROVIDE PULL STRINGS IN ALL EMPTY RACEWAYS. PULL STRINGS SHALLBE NYLON AND SHALL BE IMPERVIOUS TO MOISTURE. PULL STRINGS SHALL HAVE A TENSILE STRENGTH NOT LESSTHAN 200 LBS. METALLIC RACEWAY MAY BE BONDED TO CABINETS, BOXES AND PANELBOARDS BY DOUBLE LOCKNUTAND BUSHING TO ENSURE THE METALLIC PARTS ARE ALL EFFECTIVELY GROUNDED.

D. CONDUIT ABOVE GRADE OR CONCEALED IN WALLS SHALL BE EMT (INTERIOR ONLY), IMC OR GALVANIZED. CONDUITBELOW GRADE SHALL BE RIGID GALVANIZED (HEAVY WALL), IMC, OR PVC (SCHEDULE 40). CONNECTION TO VIBRATINGEQUIPMENT, (INCLUDING TRANSFORMERS AND HYDRAULIC, PNEUMATIC, ELECTRIC SOLENOID OR MOTOR-DRIVENEQUIPMENT), FMC, EXCEPT USE LFMC IN DAMP OR WET LOCATIONS, MAXIMUM LENGTH 72 INCHES. CONCEALCONDUIT WITHIN FINISHED WALLS, CEILINGS, AND FLOORS, UNLESS OTHERWISE INDICATED.

E. CONDUIT OUTSIDE AND EXPOSED TO PHYSICAL DAMAGE OR IN DAMP OR WET LOCATIONS SHALL BE RIGIDGALVANIZED (HEAVY WALL).

F. SEALANT: PROVIDE A CLOSED CELL SILICONE FOAM SEALANT RATED TO PROVIDE A RATING EQUAL TO THE WALL,CEILING, OR FLOOR ASSEMBLY RATING. PROVIDE SEALS FOR THE EXTERIOR OF CONDUIT PENETRATIONS CONSISTINGOF A CAST-IN-PLACE SLEEVE WITH A COMPRESSIBLE RUBBER GASKET BETWEEN THE CONDUIT AND THE SLEEVE.PROVIDE SEALS FOR THE INTERIOR OF THE CONDUIT PENETRATIONS CONSISTING OF GLAND TYPE SEALING BUSHINGOR CLOSED CELL SILICONE FOAM. PROVIDE DUCT SEAL INSIDE AN APPROPRIATE SEAL-OFF FITTING TO SEAL THEINTERIOR OF THE CONDUIT SYSTEM FROM WATER SEEPAGE OR HAZARDOUS GASES.

G. COUPLINGS: ALL COUPLINGS AND CONNECTORS FOR EMT SHALL BE OF COMPRESSION TYPE.H. OUTLET SHALL BE STANDARD TYPE, WITH KNOCKOUTS, MADE OF HOT DIPPED GALVANIZED STEEL AS MANUFACTURED

BY STEEL CITY, RACO OR APPLETON. BOX EXTENSIONS USED TO ACCOMMODATE NEW BUILDING FINISHES SHALL BEOF SAME MATERIAL AS RECESSED BOX.

I. CEILING OUTLET BOXES SHALL BE 4-INCH OCTAGON 1-1/2 INCH DEEP OR LARGER WHEN REQUIRED DUE FOR NUMBEROF CONDUCTORS OR CONDUIT ENTRY. LUMINAIRE OUTLET BOXES: NON-ADJUSTABLE, DESIGNED FOR ATTACHMENTOF LUMINAIRE WEIGHING 50 LB. OUTLET BOXES DESIGNED FOR ATTACHMENT OF LUMINAIRES WEIGHING MORE THAN50 LB SHALL BE LISTED AND MARKED FOR THE MAXIMUM ALLOWABLE WEIGHT.

J. OUTLET BOXES SHALL BE PROVIDED WITH APPROVED 3/8 INCH FIXTURE STUDS WHERE REQUIRED. PROVIDEJUNCTION OR PULL BOXES WHERE SHOWN ON THE DRAWINGS AS REQUIRED TO FACILITATE INSTALLINGCONDUCTORS. BOXES SHALL BE SIZED IN ACCORDANCE WITH THE NEC. ALL JUNCTION BOXES SHALL BEACCESSIBLE. HORIZONTALLY SEPARATE BOXES MOUNTED ON OPPOSITE SIDES OF WALLS SO THEY ARE NOT IN THESAME VERTICAL CHANNEL AND TO MAINTAIN WALL FIRE RATING.

K. METAL FLOOR BOXES: CAST METAL FOR SLAB ON SLAB ON GRADE OR SHEET METAL, FULLY ADJUSTABLE,RECTANGULAR. METAL FLOOR BOXES SHALL BE LISTED AND LABELED AS DEFINED IN NFPA 70, BY A QUALIFIEDTESTING AGENCY AND MARKED FOR INTENDED LOCATION AND APPLICATION.

260544 SLEEVES AND SEALS FOR ELECTRICAL RACEWAYS AND CABLING:A. COORDINATE SLEEVE SELECTION AND APPLICATION FOR RACEWAYS AND CABLES THROUGH FIRE RATED

PENETRATIONS WITH “THROUGH-PENETRATION FIRESTOP SYSTEMS” SPECIFIED IN ARCHITECTURAL DRAWINGS ANDSPECIFICATIONS. FOR FIRE-RATED-ASSEMBLY PENETRATIONS, MAINTAIN INDICATED FIRE RATING OF WALLS,PARTITIONS, CEILINGS AND FLOORS AT CABLE PENETRATIONS. INSTALL SLEEVES AND SEAL WITH FIRESTOPMATERIALS ACCORDING TO LISTING.

B. SLEEVE INSTALLATION FOR NON-FIRE-RATED ELECTRICAL PENETRATIONS: WALL SLEEVES, GALVANIZED-STEEL SHEET;0.0239-INCH MINIMUM THICKNESS; ROUND TUBE CLOSED WITH TABS FOR SCREW-FASTENING THE SLEEVE TO THEBOARD. SLEEVES FOR RECTANGULAR OPENINGS: FOR SLEEVE CROSS-SECTION RECTANGLE PERIMETER LESS THAN50 INCHES AND WITH NO SIDE LARGER THAN 16 INCHES, THICKNESS SHALL BE 0.052 INCH. FOR SLEEVECROSS-SECTION RECTANGLE PERIMETER 50 INCHES OR MORE AND ONE OR MORE SIDES LARGER THAN 16 INCHES,THICKNESS SHALL BE 0.138 INCH. CUT SLEEVES TO LENGTH FOR MOUNTING FLUSH WITH BOTH WALL SURFACES.EXTEND SLEEVES INSTALLED IN FLOORS 2 INCHES ABOVE FINISHED FLOOR LEVEL. SIZE PIPE SLEEVES TO PROVIDE1/4-INCH ANNULAR CLEAR SPACE BETWEEN SLEEVE AND CABLE UNLESS SLEEVE SEAL IS TO BE INSTALLED. SEALSPACE OUTSIDE OF SLEEVES WITH GROUT FOR PENETRATIONS OF CONCRETE AND MASONRY AND WITH APPROVED

JOINT COMPOUND FOR GYPSUM BOARD ASSEMBLIES. ROOF-PENETRATION SLEEVES - SEAL PENETRATION OFINDIVIDUAL CABLES WITH FLEXIBLE BOOT-TYPE FLASHING UNITS APPLIED IN COORDINATION WITH ROOFING WORK.ABOVEGROUND EXTERIOR-WALL PENETRATIONS - SEAL PENETRATIONS USING SLEEVES AND MECHANICAL SLEEVESEALS AND SIZE SLEEVES TO ALLOW FOR 1-INCH ANNULAR CLEAR SPACE BETWEEN PIPE AND SLEEVE FORINSTALLING MECHANICAL SLEEVE SEALS. UNDERGROUND EXTERIOR-WALL PENETRATIONS - INSTALL CAST-IRON"WALL PIPES" FOR SLEEVES, SIZE SLEEVES TO ALLOW FOR 1-INCH ANNULAR CLEAR SPACE BETWEEN CABLE ANDSLEEVE FOR INSTALLING MECHANICAL SLEEVE SEALS.

264113 LIGHTNING PROTECTION:A. CERTIFIED LIGHTNING PROTECTION CONTRACTOR SHALL PROVIDE THE LIGHTNING PROTECTION SYSTEM AND

PERFORM THE INSTALLATION. THE LIGHTNING PROTECTION SYSTEM SHALL BE INSTALLED AND LISTED AND LABELEDAS DEFINED IN NFPA 780, UL STANDARD 96 AND CERTIFIED WITH A UL MASTER LABEL.

B. PROVIDE LABOR, MATERIALS AND EQUIPMENT REQUIRED FOR COMPLETION OF A FUNCTIONAL SYSTEM OF AIRTERMINALS, CONDUCTORS, GROUNDS AND OTHER COMPONENTS NECESSARY FOR PROTECTION AGAINST DAMAGE BYLIGHTNING.

C. SYSTEM SHALL BE CONCEALED, WITH ONLY AIR TERMINALS AND ROOF CONDUCTORS VISIBLE. COORDINATEINSTALLATION OF LIGHTNING PROTECTION WITH INSTALLATION OF OTHER BUILDING SYSTEMS AND COMPONENTS,INCLUDING ELECTRICAL WIRING, SUPPORTING STRUCTURES AND BUILDING MATERIALS, METAL BODIES REQUIRINGBONDING TO LIGHTNING PROTECTION COMPONENTS AND BUILDING FINISHES. COORDINATE INSTALLATION OF AIRTERMINALS ATTACHED TO ROOF SYSTEMS WITH ROOFING MANUFACTURER AND INSTALLER. FLASHINGS OFTHROUGH-ROOF ASSEMBLIES SHALL COMPLY WITH ROOFING MANUFACTURERS' SPECIFICATIONS.

D. ROOF-MOUNTED AIR TERMINALS CLASS I, ALUMINUM. MAIN AND BONDING CONDUCTORS TO BE ALUMINUM. GROUNDLOOP CONDUCTOR SHALL BE THE SAME SIZE AND TYPE AS THE MAIN CONDUCTOR EXCEPT TINNED. GROUND RODSTO BE STAINLESS STEEL; 3/4 INCH IN DIAMETER BY 10 FEET LONG. LIGHTNING PROTECTION COMPONENTS TO BESTAINLESS. USE CRIMPED OR BOLTED CONNECTIONS FOR ALL CONDUCTOR SPLICES AND CONNECTIONS BETWEENCONDUCTORS AND OTHER COMPONENTS. USE EXOTHERMIC-WELDED CONNECTIONS IN UNDERGROUND PORTIONSOF THE SYSTEM.

E. METAL BODIES OF INDUCTANCE LOCATED ABOVE THE ROOF, SUCH AS METAL FLASHINGS, GRAVEL STOPS, ROOFDRAINS, PLUMBING VENTS, LOUVERS AND DOOR FRAMES, SHALL BE CONNECTED TO THE LIGHTNING PROTECTIONSYSTEM IF SITUATED WITHIN SIX FEET (6 FT.) OF A LIGHTNING CONDUCTOR OR ANOTHER BONDED METAL BODY.

F. FITTINGS SECURED BY ADHESIVE SHALL BE SET IN PLACE WITH ADHESIVE BEFORE ROOF IS APPLIED.G. INSTALL THE SYSTEM TO BLEND WITH THE APPEARANCE OF THE BUILDING, NEAT AND INCONSPICUOUS.H. SEAL EXPOSED ENDS OF CONDUITS WITH A SEALER TO PREVENT MOISTURE PENETRATION.

ELECTRICAL SPECIFICATIONS

IG

GFI - TYPE DUPLEX RECEPTACLEWP: DENOTES WEATHERPROOF COVER

GFI - TYPE DOUBLE DUPLEX RECEPTACLE

GFI - DUPLEX RECEPTACLEMOUNTED AT 48" UNLESS NOTED OTHERWISE

SPECIAL PURPOSE RECEPTACLE(NEMA RATING AS INDICATED)

QUADRUPLEX RECEPTACLE, TICK MARKSDENOTE EMERGENCY (TYPICAL ALL RECEPTACLES)

DUPLEX RECEPTACLE - HALF SWITCHED

DUPLEX RECEPTACLE - CEILING MOUNTED

DUPLEX RECEPTACLE WITH ISOLATED GROUND

JUNCTION BOX - CEILING MOUNTED

JUNCTION BOX - WALL MOUNTED

GFI - DOUBLE DUPLEX RECEPTACLE MOUNTED AT 48"UNLESS NOTED OTHERWISE

RECEPTACLE LEGENDDESCRIPTIONSYMBOL

PANELBOARD, 480 / 277V

PANELBOARD, 208 / 120V

SURGE PROTECTION DEVICE

ELECTRICAL METER

TRANSFORMER

MOTOR CONNECTION, HP: DENOTES HORSEPOWER RATING

GROUND BUS BAR

3/4" PLYWOOD TELEPHONE BACKBOARD

CONCRETE ENCASED DUCTBANK

EXHAUST FANEF

HP

SPD

TX

MISCELLANEOUSDESCRIPTIONSYMBOL

CONDUIT TURNING UP

DUPLEX RECEPTACLE, 20 AMP, 120V U.O.N.

SINGLE RECEPTACLE, 20 AMP, 120V U.O.N.

QUADRUPLEX RECEPTACLE, 20 AMP, 120V U.O.N.

SCOPE OF WORK

1. #12 AWG NEUTRAL CONDUCTOR ALTHOUGH NOT INDICATED SHALL BE INCLUDEDFOR EACH BRANCH CIRCUIT UNLESS OTHERWISE NOTED.

2. #12 AWG GREEN GROUND CONDUCTOR, ALTHOUGH NOT INDICATED SHALL BEINCLUDED IN EACH RACEWAY UNLESS OTHERWISE NOTED.

3. HOME RUNS TO PANEL BOARDS SHALL HAVE A MAXIMUM OF THREE (3) PHASECONDUCTORS (ONE PER PHASE) PLUS DEDICATED NEUTRAL FOR EACH PHASECONDUCTOR AND GROUND CONDUCTOR IN EACH CONDUIT.

4. ALL SYMBOLS SHOWN MAY NOT BE USED.

ENCLOSED CIRCUIT BREAKER, AS INDICATED

PP

MANHOLEMH

HAND HOLEHH

DUPLEX RECEPTACLE - FLOOR MOUNTED

JUNCTION BOX - FLOOR / GROUND MOUNTEDJ

J

J

HOMERUN TO PANEL INDICATED (CONCEALED)NUMBER OF ARROWS INDICATE NUMBER OF CIRCUITS

MAGNETIC MOTOR STARTER

WIRE IN CONDUIT CONCEALED, #12 AWG SIZE WIRE IN1/2" CONDUIT MINIMUM UNLESS OTHERWISE NOTED

WIRE IN CONDUIT CONCEALED BELOW SLAB OR GRADE

PUSHBUTTON

3P/60ANF 3R

3P/60AF: 50A 3R

3P/60ANEMA X 3R

DISCONNECT SWITCH, NON-FUSIBLE3 POLE, 60 AMP, NF = NON-FUSED, 3R = NEMA 3R ENCLOSURE

DISCONNECT SWITCH, FUSIBLE

COMBINATION STARTER / DISCONNECT SWITCH, FUSIBLE

3 POLE, 60 AMP, FUSED AT 50 AMPS, 3R = NEMA 3R ENCLOSURE

3 POLE, 60 AMP, NEMA X SIZE, 3R = NEMA 3R ENCLOSURE

CONDUIT EXPOSED

FLEXIBLE CONDUIT

CONDUIT TURNING DOWN

CONDUIT STUB

DUPLEX RECEPTACLE, 20 AMP, 120V U.O.N.MOUNTED AT 48" UNLESS NOTED OTHERWISE

WIRE IN CONDUIT CONCEALED, #12 AWG SIZE WIRE IN1/2" CONDUIT MINIMUM UNLESS OTHERWISE NOTED

GENERAL NOTES

NFPA 70: NATIONAL ELECTRICAL CODE (2011)

NFPA 72: NATIONAL FIRE ALARM CODE (2010)

NFPA 75: STANDARD FOR THE PROTECTION OF ELECTRONIC COMPUTER / DATAPROCESSING EQUIPMENT (2009)

NFPA 90A: STANDARD FOR THE INSTALLATION OF AIR CONDITIONING AND VENTILATING SYSTEMS (2012)

NFPA 90B: STANDARD FOR THE INSTALLATION OF WARM AIR HEATING AND AIR CONDITIONING SYSTEMS (2012)

NFPA 92: RECOMMENDED PRACTICE FOR SMOKE CONTROL SYSTEMS (2012)

NFPA 101: LIFE SAFETY CODE (2012)

NFPA 110: STANDARD FOR EMERGENCY AND STANDBY POWER SYSTEMS (2010)

2014 EDT: FLORIDA BUILDING CODE

CODES AND STANDARDS

SHEET INDEX

QUADRUPLEX RECEPTACLE, 20 AMP, 120V U.O.N.MOUNTED AT 48" UNLESS NOTED OTHERWISE

POWER POLE

1. PROVIDE AND INSTALL A COMPLETE LIGHTNING PROTECTION SYSTEM.

2. RE-ROUT UNDERNEATH SIDE WALK THE OVERHEAD ELECTRICAL POWER /SIGNAL CONDUITS AND CONDUCTORS SPANNING BETWEEN MECHANICALEQUIPMENT AREA AND MECHANICAL / ELECTRICAL ROOM .

PARTIAL ELECTRICAL RISER

EXISTINGMAIN 800A

SWITCHBOARD

'MDP'

1

SPD2

1. COORDINATE POWER OUTAGE WITH ELECTRICAL POWER COMPANY TO INSTALLSURGE PROTECTION DEVICE. CONNECT SPD TO MAIN BUS WITH SHORTEST LEADPOSSIBLE.

2. PROVIDE SERVICE ENTRANCE RATED SPD WITH INTEGRAL BREAKER. APT MODEL#TE02XAS20E1D OR EQUIVALENT.

GENERAL NOTES

TOLEDO BLADE FACILITYHARDENING

FLORIDA POWER &LIGHT COMPANY

15.29512.00

One Tampa City Center, Suite 1800,Tampa, FL 33602

FL Reg.: AAC001139

t +1 813 229 0300 f +1 813 223 7116

Sheet Number

Original drawing is 42 x 30. Do not scale contents of this drawing.

Sheet Title

Project No:

Drawn by: Reviewed by:

Professional Seals

Key Plan

In Association with

Project

No. Description Date

THORTON TOMASETTI

101 NE Third Avenue, Suite 1170Fort Lauderdale, FL 33301t 954-903-9300 f 954-903-9301

Structural Enginners

Prepared For

Contract No:

Client Location

All reproduction & intellectual property rights reserved © 2016

HOK

VOLTAIR CONSULTING ENGINEERS

220 W 7th Ave #210,Tampa, FL 33602t 888.891.9713

MEPF Engineers

TOLEDO BLADE FACILITYHARDENING2245 MURPHY COURT, NORTH PORT, FLORIDA

FLORIDA POWER &LIGHT COMPANY

15.29512.00

Filen

ame:L

:\201

6-JO

BS\01

.1603

0 - F

PL T

oledo

& B

reva

rd F

acilit

ies\C

AD\S

heets

\E00

0 ELE

CTRI

CAL S

PECI

FICA

TION

S, LE

GEND

& R

ISER

Plot

Date

:5/5/2

016 3

:53 P

M Pl

otted

By:A

aron

Jose

ph

DAVI

D A.

FRE

EMAN

PE #

5488

5DAV I D A . FREEMANL I C E N S E

F L OR I DA

NO. 54885

STATE OF

PROFESS I ONA L ENG I NEE

R

1 BID DOCUMENTS 05.06.16

ELECTRICALSPECIFICATIONS,LEGEND & RISER

E000

DFAJ

Sheet Number Sheet TitleE000 ELECTRICAL SPECIFICATIONS, LEGEND & RISER

E201 LIGHTNING PROTECTION PLAN