the updated drilled shaft manual - stgec conference stge… · · 2017-01-25the updated drilled...
TRANSCRIPT
![Page 1: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/1.jpg)
The Updated Drilled Shaft Manual:Potential Impacts on AASHTO Specifications
J. Turner & D. Brown
May 24, 2010
AASHTO T-15
Sacramento, CA
![Page 2: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/2.jpg)
2
Drilled Shafts:
Construction Procedures and
LRFD Design Methods
Update and Revision of NHI Manual by O‟Neill and Reese (1999)
Contractor: Parsons Brinckerhoff (PB), New York
FHWA: Silas Nichols, Jeremy DiMaggio
PB Project Manager: Mr. Jeremy Hung
Authors: Dr. Dan Brown, Dan Brown & Associates
Dr. John Turner, University of Wyoming
Mr. Raymond Castelli, PB
![Page 3: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/3.jpg)
3
Objective
Identify issues addressed in the revised manual
that the authors believe should be brought to the
attention of Committee T-15, for making future
updates to the AASHTO LRFD Bridge Design
Specifications.
The list is not exhaustive; rather it highlights
some of the most significant issues
![Page 4: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/4.jpg)
1. Design for Lateral Loading
Article 10.8.3.1 identifies
‘lateral geotechnical resistance of soil and rock
stratum’
as a strength limit state for design of drilled shafts
Article 10.8.3.8 Nominal Horizontal Resistance of
Shaft and Shaft Groups: “The provisions of Article
10.7.3.12 apply” (driven piles)
C10.7.3.12: “The strength limit state for lateral
resistance is only structural”
4
![Page 5: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/5.jpg)
Use of Analytical Method for DesignA Rational Approach:
For a given trial shaft diameter, establish the
depth of embedment at which a strength limit
state occurs by overturning of the shaft (a
pushover analysis).
This is the limit state controlled by the strength
of the supporting soil and rock strata.
5
![Page 6: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/6.jpg)
Use of Analytical Method for DesignApproach Presented in Ch. 12 of the
Revised Manual:
• Model the shaft as linear elastic beam
• Perform p-y analyses to find minimum length for stable solution with (1/φ) x factored loads
• Use φ = 0.67 for Strength I-V Load Cases
• Use φ = 0.8 for Extreme Event Load Cases
6
![Page 7: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/7.jpg)
2. Axial Side Resistance: Cohesionless Soil
'h = K 'v
fSN = 'h tan
side resistance: effective stress analysis
h = horizontal effective stress, which acts as a
normal stress at the soil/foundation interface
= interface angle of friction (soil/concrete) = f' K = coefficient of lateral earth pressure 7
![Page 8: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/8.jpg)
Nominal Unit Side Resistance
Cohesionless Soils
fSN = v K tan f
fSN = b v
8
‘Beta method’
![Page 9: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/9.jpg)
Changes to the ‘Beta method’
9
fSN = b 'v
Currently: Depth-dependent b method
(O’Neill & Reese, 1999)
For sandy soils:
b = 1.5 – 0.135 (z)0.5
for N60 > 15
![Page 10: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/10.jpg)
Rational Method for Nominal Unit Side
Resistance in Cohesionless Soils
fSN = v K tan f
from correlation with
N60 and vvalue at middle of
layer of interest
from correlation with N60, v and f’
10
![Page 11: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/11.jpg)
Comparison: Depth-Dependent versus
Rational Method for b
11
0
10
20
30
40
50
60
70
80
90
100
0 0.5 1 1.5 2 2.5 3 3.5
Beta Coefficient, b
Dep
th (f
t)
N60 = 50
N60 = 15All N 60 > 15
See Appendix C for full
discussion
![Page 12: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/12.jpg)
3. Updated Load-Settlement Model
12
0
50
100
150
200
0 1 2 3 4 5 6 7 8 9 10 11 12
Axial Compressive Force ----------------------------------- (%)
Nominal Resistance
Displacement---------------------------- %
Shaft Diameter
Nominal Resistance
Full mobilization of base resistance, cohesionless
0.4 %
Cohesive Soil
![Page 13: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/13.jpg)
4. Downdrag
• Article 10.8.2.4 „Settlement Due
to Downdrag‟, refers the user to
Article 10.7.2.4 (Piles)
• Article 10.8.3.4 „Downdrag‟, for
strength limit state design, refers
the user to Article 10.7.3.6 (Piles)
• Ditto on commentary (refers the
reader to provisions for driven
piles)
NP
Stable Geomaterial
13
![Page 14: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/14.jpg)
Comments on Downdrag
• Section 13.6.5 of the revised manual addresses
downdrag specifically for drilled shafts; stand-alone
AASHTO provisions for drilled shafts should be
considered
• Service limit state (settlement) will control in most
cases
• May be appropriate to consider different load
combinations for evaluation of geotechnical strength
limit states than for structural strength limit states,
when downdrag occurs (e.g., geotechnical strength
limit states should be limited to permanent load only +
downdrag)14
![Page 15: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/15.jpg)
5. Base Grouting
• Not currently addressed in AASHTO
• Research and experience are now sufficiently
advanced for inclusion in transportation practice
• Design equations in Appendix C (Section C.3) of
Manual
• Requires development of resistance factors15
(a) (b) (c) (d)
![Page 16: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/16.jpg)
6. Structural Issue:Tightly Spaced Transverse Reinforcement
• Transverse reinforcement
requirements (Section 5)
• Seismic Zones 2, 3, and 4:
smax = 4.0 inches to depth of
3B below fixity
• Conflicts w/ constructability
smin = larger of 5.0 inches or
5X max aggregate size
16
![Page 17: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/17.jpg)
7. Structural Issue:
Resistance with Permanent Casing
• Article 5.13.4.5 „Cast-In-Place Piles‟ includes both
drilled shafts and piles cast in driven steel shells,
but does not specifically cover design of drilled
shafts with both reinforcing cage and permanent
casing
• Casing provides confinement, increased flexural
stiffness, increased axial and flexural strength
• Recommend adding information to cover this topic
specifically for drilled shafts
17
![Page 18: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/18.jpg)
8. Depth of Borings
Table 10.4.2-1:
“For shafts supported on or extending into rock, a
minimum of 10 ft. of rock core, or a length of rock core
equal to at least three times the shaft diameter for
isolated shafts or two times the maximum shaft group
dimension, whichever is greater, shall be extended below
the anticipated shaft tip elevation to determine the
physical characteristics of rock within the zone of
foundation influence.”
The above may be unrealistic for groups of drilled
shafts18
![Page 19: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/19.jpg)
19
B
3B 3B
7B
14B
Drill to HERE
ROCK
![Page 20: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/20.jpg)
20
• Resistance factors and definition of a „site‟ for static load
testing of drilled shafts is tied to Table 10.5.5.2.3-2.
• Text in Article 10.5.5.2.3 says this table to be used together
with signal matching analysis of dynamic test data
(intended for driven piles)
9. Definition of a Site for
Static Load Test
![Page 21: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/21.jpg)
21
10. Resistance Factors, Group
Redundancy, and Load Testing
• 20 percent increase in resistance factors allowed for groups
of five or more drilled shafts
– Example: j = 1.2 x 0.55 = 0.66
• For static load testing, max resistance factor of 0.70 allowed
• For groups of 5 or more shafts, incentive to conduct static
load testing is thus greatly diminished
• Reconsider the 20 percent increase for groups of 5 or more
shafts; consider allowing a single shaft within a group to
carry a higher load by increasing resistance factor
![Page 22: The Updated Drilled Shaft Manual - STGEC Conference STGE… · · 2017-01-25The Updated Drilled Shaft Manual: ... but does not specifically cover design of drilled shafts with both](https://reader031.vdocuments.mx/reader031/viewer/2022022517/5b04fa807f8b9a2e228ea364/html5/thumbnails/22.jpg)
22
Summary
• Proposed analysis for lateral geotechnical strength fulfills a
need that is not being addressed currently with a rational
approach that can be implemented using existing analytical
tools
• Replacing the depth-dependent b method is a long-overdue
improvement for design of shafts in cohesionless soils
• Additional refinements are identified to address downdrag,
base grouting, structural design, depth of borings, and shaft
redundancy
• Calibrations are needed to establish resistance factors for
newly-proposed design equations and to update existing
methods