the following demo demonstrates features and benefits of the fasfold cnc controller when
DESCRIPTION
The following demo demonstrates features and benefits of the Fasfold CNC controller when retrofitted to a new or used Slitter Folder. It uses a 15 “color touch screen which makes it lightning fast to alter or enter things. It can control from 2 to 4 axis. - PowerPoint PPT PresentationTRANSCRIPT
The following demo demonstrates features and benefits of the Fasfold CNC controller when
retrofitted to a new or used Slitter Folder
It uses a 15 “color touch screen which makes it lightning fast to alter or enter things.
There are 43 slidesUse the left mouse click to go to the next slide.
Use the Backspace key to go to the previous slide.You can also run the actual program from your desktop.
It can control from 2 to 4 axis. It can utilize AC or DC servo control
Whenever you press on any value….
This keypad pops up which allows you to enter data
Finger touch Quickdraw to go to the Quickdraw screen
Touch here to start the profile
Touch here for end of 1st length
Touch here for next bendTouch here to change the grid size
Touch here for next bend
Touch here for last bendLets say we placed it on
the wrong corner. Use the Undo button to erase.
Undo
Undo erased the last bend
Touch here to place the last bend correctly
Use Draw/Edit to make changes
Touch this corner to move it in
Touch this corner to move it in
Touch this corner to move it o
ut again
Use OK to return to The Main Screen
Any values can be altered here to fine tune the profile
Dimensions in the first and Angle in the second column
Use Insert to insert a slit before a bend
Enter the bend number where the slit needs to be inserted
1
This is the Backgauge position For the slit based on the total of all the dimensions of the profileIt can be altered if needed. It is
calculated automatically. Press OK.
This is the total length of the profile above
28.2 plus..
90 plus..
50 plus..
14.2 = 182.4
182.4 for the first slit
The (- blue) for fold 2 & 3 indicates the folds is
done on the bottom side of the material
The ( -) Blue in the first column indicates the fold
needs to be done from the rear of the material
Use sequence to select a specific folding order
other than 1234
Next is 4 then 3 for the next 2 folds
First press 1 for the slit
Lastly press 2 for the last fold
You have now selected a 231 sequence
( if the slit is ignored)
By pressing on any fold number below
Simulate any fold…
This fold needs to be Done from the rear…
So this needs to change to minus 28.2
Now the profile sits on the outside rather than the inside
Use this key to change Between 1 & 2 operators
Use this key to change Between 1 & 2 operators
Use this key to enter a job number
With alphanumeric characters
Use this key to save the job
Enter the password
And press OK
Use this key to open a new job
Press Yes
Touch on the Job you want
Or press UP & Down to scroll to another page
The job opens with all relevant data like which folds is done from the rear or bottom etc
Also the previous fold sequence..Saves a lot of time.
Fold 1 needs to be changed to (-) in the first column
So the material sits outside the folder
Use this to Toggle Between Auto & Manual mode
Use this to Toggle Between Auto & Manual mode
This will take you to the Calibrate& Setup screen
When any input switches or outputs activated, they change between green and red.
It is so quick and powerful to do diagnostics.When you press the footswitch, it changes to green and if the valve operates, it changes
color as well. This minimizes down time.
Valves
Valves
Foot switches
Backgauge motor
Hydrau
lic pump
Encod
er
Top switch
Bottom switch This takes you to the Parameter screen
This is the Backgauge slow speed, fast speed,
Tolerance etc.
This is the Apron slow speed, fast speed,
Tolerance etc.
This takes you to the Calibration
Calibration is as easy as entering the actual measured
values in here.
This takes you backTo the Main screen
This button downloads the job to the PLC on the machine
Jobs can also be downloaded from the office