technical manual of intel 1037u cpu + intel nm70 chipset ... · technical manual of intel 1037u cpu...
TRANSCRIPT
TECHNICAL MANUAL
Of
Intel 1037U CPU + Intel NM70 Chipset
Based Mini-ITX M/B
NO. G03-NC9T-F
Revision: 1.0
Release date: October 15, 2013
Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
i
Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.
ii
ENVIRONMENTAL SAFETY INSTRUCTION........................................................................... iii USER’S NOTICE ....................................................................................................................... iv MANUAL REVISION INFORMATION....................................................................................... iv ITEM CHECKLIST ..................................................................................................................... iv CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD................................................................................1 1-2 SPECIFICATION .........................................................................................................2 1-3 LAYOUT DIAGRAM....................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION 2-1 JUMPER SETTING .....................................................................................................8 2-2 CONNECTORS AND HEADERS................................................................................16
2-2-1 CONNECTORS .............................................................................................16 2-2-2 HEADERS .....................................................................................................20
CHAPTER 3 INTRODUCING BIOS 3-1 ENTERING SETUP .....................................................................................................26 3-2 BIOS MENU SCREEN ................................................................................................27 3-3 FUNCTION KEYS .......................................................................................................27 3-4 GETTING HELP ..........................................................................................................28 3-5 MEMU BARS...............................................................................................................28 3-6 MAIN MENU ................................................................................................................29 3-7 ADVANCED MENU.....................................................................................................30 3-8 CHIPSET MENU..........................................................................................................37 3-9 BOOT MENU...............................................................................................................41 3-10 SECURITY MENU .......................................................................................................43 3-11 SAVE & EXIT MENU...................................................................................................44
TABLE OF CONTENT
iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet.
0 to 60 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
Generally speaking, dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots’ that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
iv
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.
Manual Revision Information Reversion Revision History Date 1.0 First Edition October 15, 2013
Item Checklist Motherboard DVD for motherboard utilities User’s Manual Cable(s) I/O Back panel shield
1
Chapter 1 Introduction of the Motherboard
1-1 Feature of Motherboard Intel® 1037 dual-core CPU+ Intel® NM70 express chipset Support 1 * DDRIII SO-DIMM 1066/1333/1600 MHz up to 8GB Support Mini-PCIE connector Support m-SATA connector Integrated with 24-bit dual channel LVDS header Support 1 * Serial ATAII (3Gb/s) & 1 * Serial ATAIII (6Gb/s) Devices Support HDMI and VGA Video Outputs Supports ACPI S3 Function Support CPU Smart FAN Support Watchdog Timer Technology Support Windows8 OS Compliance with EuP Standard
2
1-2 Specification Spec Description Design Mini-ITX form factor;
PCB size: 17.0 x 17.0 cm Embedded CPU Intel® 1037U Dual Core CPU (1.8GHz)
Chipset Intel® NM70 Express Chipset
Memory Slot 1* DDRIII SO-DIMM slot Support DDRIII 1333/1600 MHz DDRIII SO-DIMM
expandable to 8GB
Expansion Slot 1 * PCI Express x1 slot 1 * halt-size Mini-PCIE slot
Storage 1* SATA III 6G/s connector 1* SATA II 3G/s connector 1 * full-size M-SATA/ Mini-PCIE selectable slot
Dual LAN Chip
Integrated with dual Realtek RTL8111G PCI-E Gigabit LAN chip
Support Fast Ethernet LAN function of providing 10/100/1000Mbps Ethernet data transfer rate
Audio Chip Realtek ALC662 2-CH HD Audio Codec integrated Audio driver and utility included
BIOS 32M DIP Flash ROM
Multi I/O
Rear Panel I/O: 1* 12V DC in power connector 1* RJ-11port 1* PS/2 keyboard & mouse combo port 1 * VGA port 1* HDMI port 1* serial port (COM1) 1* parallel port 4* USB 2.0/1.1 port 2* RJ-45 port
3
1* Line-out connector 1* MIC connector
Internal I/O Connectors& Headers: 1 *2-pin ATX12V internal power connector 1 *4-pin SATA power connector 3* fan connector 1* speaker connector 1* LVDS inverter connector 1 * Front panel audio header 1* speaker header 1* PWRLED connector 1 * Front panel header 1 * 9-Pin USB 2.0/1.1 header for two USB 2.0/1.1 ports 1 *24-bit dual channel LVDS header 5 * serial port header 1 *GPIO header 2* LAN activity LED header
1-3 Layout Diagram Rear IO Diagram
DC 12V Power-in
Connector
VGA Port Parallel Port
HDMI Port Serial Port 1RJ-11 Port USB 2.0 Ports
RJ-45 LAN Ports
Line-Out
MIC-In
PS/2 KB & MS Combo Port
4
Motherboard Internal Diagram
*Rear IO: Please refer to Page3 (Rear IO Diagram).
ATX12V Power connector
DDRIII SODIMM Slot
Intel CPU
Intel NM70 Chipset
PCI Express x1 SlotCPUFAN Header
Front Panel Audio Header
Front Panel Header
*Rear IO
LVDS Inverter
Serial Port Headers(COM6/5/4/3/2)
GPIO Header
SATA Hard Disk Power-Out Connector
SpeakerConnector
USB 2.0 Header
LVDS Header
SATAIII Port (SATA1)
SATAII Port (SATA2)
Full-size Mini-PCIE /M-SATA Selectable slot
(MPE1)
SYSFAN2 Header
SpeakerHeader PWRLED
Header
SYSFAN1 Header
LAN1_LED Header
LAN2_LED Header
Half-size Mini-PCIE slot
(MPE2)
BUZZ
5
Motherboard Jumper Position
JBAT
AT_MODE
JP1
JP7
JP11
JP10
JP12
SYSFAN_DET
COPEN
JP6
JP9
JP2
JP4
JP8
JP5JP3
6
Jumper Jumper Name Description
JBAT CMOS RAM Clear Function Setting 3-pin Block SYSFAN_DET SYSFAN1/ SYSFAN2 R.P.M. Select 3-pin Block JP1 INVERTER Backlight VCC 5V/12V Select 3-pin Block JP7 INVERTER Backlight Mode Select 3-pin Block JP8 LCD VCC 3.3V/5V/12V Select 4-pin Block JP2 Mini-PCIE & MSATA Slot (MPE1)
VCC 3.3V/3VSB Select 3-pin Block
JP12 RJ-11 VCC 12V/24V Select 3-pin Block JP9 COM1Port Pin9 Function Select 4-pin Block JP4 COM2 Header Pin9 Function Select 4-pin Block JP3 COM3 Header Pin9 Function Select 4-pin Block JP5 COM4 Header Pin9 Function Select 4-pin Block JP10 COM5 Header Pin9 Function Select 4-pin Block JP11 COM6 Header Pin9 Function Select 4-pin Block JP6 ME Unlock Select 2-pin Block COPEN Case Open Message Display Function 2-pin Block AT_MODE AT MODE Function Select 2-pin Block
Connectors Connector Name
DCIN DC 12V Power–in Connector RJ-11 RJ-11 Connector PS2 PS/2 keyboard & mouse combo port VGA Video Graphic Attach Connector HDMI High-Definition Multimedia Interface COM1 Serial Port Header LPT Parallel Port Header USB1_LAN1(Middle & Bottom ), USB2_LAN2(Middle & Bottom )
USB 2.0 Port Connector x4
USB1_LAN1(Top),USB2_LAN2(Top) RJ-45 LAN Connector x2
7
AUDIO(Top) Audio Line Out Connector AUDIO(Bottom) Audio MIC Connector ATXPWR 12V Power-in Connector SATAPW SATA Power out Connector SATA1 SATAIII Connector SATA2 SATAII Connector MPE1 Full-size MSATA/Mini-PCIE Connector MPE2 Half-size Mini-PCIE Connector SYSFAN1,SYSFAN2,CPUFAN FAN Connector X3 SPEAK Speaker Connector INVERTER LVDS Inverter Connector
Headers Header Name Description
FP_AUDIO Front Panel Audio Header 9-pin Block FP
Front Panel Header(PWR LED/ HD LED/Power Button /Reset)
9-pin Block
SPEAK1 Speaker Header 4-pin Block PWRLED PWRLED Header 3-pin Block FP_USB USB 2.0 Port Header 9-pin Block LVDS LVDS Header 30-pin BlockCOM2/3/4/5/6 Serial Port Header X5 9-pin Block GPIO GPIO Header 10-pin blockLAN1_LED,LAN2_LED LAN Activity LED Header x2 2-pin Block
8
Chapter 2 Hardware Installation
2-1 Jumper Setting (1) JBAT (3-pin): CMOS RAM Clear Function Setting
CMOS Clear Setting
2-3 Closed：Clear CMOS.
JBAT
1-2 Closed： Normal；
3
1
3
1
(2) SYSFAN_DET (3-pin): SYSFAN1/SYSFAN2 R.P.M. Select
SYSFAN_DET
1-2 Closed： SYSFAN1 R.P.M. Selected;
3
1
3
1
2-3 Closed： SYSFAN2 R.P.M. Selected.
9
(3) JP1 (3-pin): INVERTER Back Light VCC 5V /12V Select
2-3 Closed: Back Light VCC=12V.
JP1→INVERTER Back Light VCC
1-2 Closed: Back Light VCC=5V;
1 3
1 3
(4) JP7 (3-pin): INVERTER Back Light Mode Select
2-3 Closed: Back Light DC Mode Selected.
JP7→INVERTER Back Light Mode
1-2 Closed: Back Light PWM Mode Selected;
1 3
1 3
10
(5) JP8 (4-pin): LCD Back Light VCC 3.3V/5V/12V Select
JP8→LCD Back Light VCC
4-6 Closed: LVDS VCC= 12V.
642
3-4 Closed: LVDS VCC= 5V;
2-4 Closed: LVDS VCC= 3.3V;
31 5 1 3 5
2 4 6
1 3 5
2 4 6
(6) JP2 (3-pin): MINI-PCIE & MSATA Slot (MPE1) VCC3.3V/ 3.3VSB Select
2-3 Closed: MPE1 Slot VCC=3VSB.
JP2→MPE1 Slot VCC
1-2 Closed: MPE1 Slot VCC= 3.3V;
1
3
1
3
11
(7) JP12 (3-pin): RJ-11 VCC 12V/24V Select
2-3 Closed: RJ11 VCC= 24V.
JP12→RJ-11 VCC
1-2 Closed: RJ11 VCC= 12V;
1
3
1
3
(8) JP9 (4-pin): COM1 Port Pin9 Function Select
JP9→COM1 Port
4-6 Closed: RI= 12V.
642
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
31 5 1 3 5
2 4 6
1 3 5
2 4 6
12
(9) JP4 (4-pin): COM2 Header Pin9 Function Select
JP4→COM2 Header
4-6 Closed: RI= 12V.
642
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
31 5 1 3 5
2 4 6
1 3 5
2 4 6
(10) JP3 (4-pin): COM3 Header Pin9 Function Select
JP3→COM3 Header
4-6 Closed: RI= 12V.
642
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
31 5 1 3 5
2 4 6
1 3 5
2 4 6
13
(11) JP5 (4-pin): COM4 Header Pin9 Function Select
JP5→COM4 Header
4-6 Closed: RI= 12V.
642
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
31 5 1 3 5
2 4 6
1 3 5
2 4 6
(12) JP10 (4-pin): COM5 Header Pin9 Function Select
JP10→COM5 Header
4-6 Closed: RI= 12V.
135
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
46
2
6 531
42
531
6 4 2
14
(13) JP11 (4-pin): COM6 Header Pin9 Function Select
JP11→COM6 Header
4-6 Closed: RI= 12V.
135
3-4 Closed: RI= 5V;
2-4 Closed: RI=RS232;
46
2
6 531
42
531
6 4 2
(14)JP6 (2-pin): ME Unlock Select
1-2 Closed: ME Unlocked.
JP6
1 2
1-2 Open: Normal ;
1 2
15
(15)AT_MODE (2-pin): AT Mode Function Select
1-2 Closed: AT Mode Selected.
AT_MODE
1 2
1-2 Open: ATX Mode Selected;
1 2
Pin 1-2 closed: AT_MODE function is enabled. User needs to restart the system for the settings to take effect. In this case your computer will automatically turns on when power supply resumes. (16)COPEN (2-pin): Case Open Message Display Function Select
1-2 Closed : Case Open Function Selected.
COPEN 1
2
1-2 Open: Normal;
1
2
16
Pin 1-2 Closed: Case open display function enabled. Use needs to enter BIOS and enable ‘Case Open Detect’ function. In this case if you case is removed, next time when you restart your computer a message will be displayed onscreen to inform you of this. 2-2 Connectors and Headers 2-2-1 Connectors (1) Rear IO Connectors
(2) COM1 (9-pin block): COM1 port can function as RS232/422/485 port. In normal settings this port function as RS232 port. User need to go to BIOS to select COM1 function mode at first, before using specialized cable to connect different pins of this port.
For RS422 Mode
RS422 TX(B) RS422 TX(A) RS422 RX(A) RS422 RX(B)
For RS485 Mode
RS485 D-(B) RS485 D+(A)
DC 12V Power-in
Connector
VGA Port Parallel Port
HDMI Port Serial Port 1 RJ-11 Port USB 2.0 Ports
RJ-45 LAN Ports
Line-Out
MIC-In
PS/2 KB & MS Combo Port
17
(3) ATXPWR (2-pin block): DC12V Power-in Connector
Pin1
Pin No. Definition 1 GND 2 +12V DC_IN
(4) SATAPW (4-pin):SATA Hard Disk Power-out Connector
Pin 1
+12V
GN
D+5V
GN
D
18
(5) SATA1: SATAIII Port connector This connector is a high-speed SATAIII port that supports 6 GB/s transfer rate.
Pin No. Defnition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND
(6) SATA2:SATAII Port connector This connector is a high-speed SATAII port that supports 3 GB/s transfer rate.
Pin No. Defnition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND
19
(7) CPUFAN (4-pin)/SYSFAN1 (4-pin) /SYSFAN2 (4-pin): FAN Connectors
Fan SpeedC
ontrol
+12V Fan Power
Pin1
GN
D
GND+12V Fan Power Fan Speed Control
CPUFAN/SYSFAN2
SYSFAN1
Pin1
(8) SPEAK (4-pin): Speaker Connector
Pin1
SPKL-
SPEAK
SPKL+SPK
R+
SPKR
-
20
(9) INVERTER (8-Pin): LVDS Inverter Connector
INVERTER
Pin 1
Pin No. Definition 1 Backlight Enable 2 Backlight Duty 3 Backlight Power 4 Backlight Power 5 GND 6 GND 7 Backlight+ SW 8 Backlight- SW
2-2-2 Headers (1) FP_AUDIO (9-pin): Line-Out, MIC-In Header This header connects to Front Panel Line-out, MIC-In connector with cable.
MIC2-L
SENSE-FB
GND
LINEOUT2-R
Pin 1
2
MIC2-R
LINEOUT2-L
NC NC
NC
21
(2) SPEAK1 (4-pin): Speaker Header This 4-pin header connects to the case-mounted speaker. See the figure above.
SPEAK1 SPK
+
NC
NC
SPK-
Pin 1
(3) PWR LED (3-pin): Power LED Header The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin header.
PWRLED Pin 1
PWR
LED+
PWRLED
-
PW
RLED-
22
(4) FP (9-pin): Front Panel Header
HDLED
RESET
HDD
LED+
GND
PWR
LED+
PW
RBTN
GND
PW
RLED-
HD
DLED-
RSTSW
VC
C5
PWR
BTN
Pin 1
2
PWR
LED
(5) F_USB (9-pin): USB 2.0 Port Header
VCC
GND
VCC
DATA- DATA-
GNDDATA+
Pin 1
DATA+
NC
23
(6) COM2/3/4/5/6 (9-Pin): Serial Port Headers
Serial Port Header
DC
D Pin1Pin6
Pin5 SIN
SO
UT
DTR
GN
D
DSR
RTS
C
TS
RI
(7) LVDS (30-Pin): 24-bit dual channel LVDS Header
LVDS Header
Pin 1Pin 2
24
Pin NO. Pin Define Pin NO. Pin Define Pin 1 LVDSB_DATAN3 Pin 2 LVDSB_DATAP3 Pin 3 LVDS_CLKBN Pin 4 LVDS_CLKBP Pin 5 LVDSB_DATAN2 Pin 6 LVDSB_DATAP2 Pin 7 LVDSB_DATAN1 Pin 8 LVDSB_DATAP1 Pin 9 LVDSB_DATAN0 Pin 10 LVDSB_DATAP0 Pin 11 LVDS_DDC_DATA Pin 12 LVDS_DDC_CLK Pin 13 NA Pin 14 GND Pin 15 GND Pin 16 GND Pin 17 LVDSA_DATAP3 Pin 18 LVDSA_DATAN3 Pin 19 LVDS_CLKAP Pin 20 LVDS_CLKAN Pin 21 LVDSA_DATAP2 Pin 22 LVDSA_DATAN2 Pin 23 LVDSA_DATAP1 Pin 24 LVDSA_DATAN1 Pin 25 LVDSA_DATAP0 Pin 26 LVDSA_DATAN0 Pin 27 PVDD Pin 28 NA Pin 29 PVDD Pin 30 PVDD Pin 31 GND Pin 32 GND
(8) GPIO1 (10-pin): GPIO Header
GPIO34
GPIO71
GPIO37
GPIO38 GPIO39
GPIO70 GPIO69
Pin 1
GPIO68
VCC GND
2
25
(9) LAN1_LED/LAN2_LED (2-pin): LAN Activity LED Header
LAN1_LED
Pin1
LED+
LED-
LAN2_LED
Pin1 LED+ LED-
26
Chapter 3 Introducing BIOS
Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.
3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <Del> to enter Setup
27
3-2 BIOS Menu Screen The following diagram show a general BIOS menu screen:
BIOS Menu Screen
3-3 Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here:
Press←→ (left, right) to select screen; Press ↑↓ (up, down) to choose, in the main menu, the option you want to confirm
or to modify.
Menu Bar
Menu Items Current Setting Value
Function Keys
General Help Items
28
Press <Enter> to select. Press <+>/<–> keys when you want to modify the BIOS parameters for the active
option. [F1]: General help. [F2]: Previous value. [F3]: Optimized defaults. [F4]: Save & Reset. Press <Esc> to quit the BIOS Setup.
3-4 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the top right corner the screen.
Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>.
3-5 Menu Bars There are seven menu bars on top of BIOS screen: Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Boot To change boot settings Security Password settings Save & Exit Save setting, loading and exit options User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted.
29
3-6 Main Menu Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item.
System Date Set the date. Please use [Tab] to switch between data elements. System Time Set the time. Please use [Tab] to switch between time elements.
30
3-7 Advanced Menu
ERP Support The optional settings: [Enabled]; [Disabled]. Use this item to enable or disable Energy-Related Products function for this board. This item should be set as [Disabled] to activate all wake-up functions.
► ACPI Settings Press [Enter] to make settings for the following sub-items: ACPI Settings ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed. The optional settings are: [Suspend Disabled]; [S3 only (Suspend to RAM)].
31
► Wakeup function Settings Press [Enter] to make settings for the following sub-items: Wake System with Fixed Time Use this item to enable or disable system wake on alarm event. When set as [Enabled], system will wake on the hour/min/sec specified. PS2 KB/MS Wakeup The optional settings: [Enabled]; [Disabled]. Use this function to enable or disable PS/2 keyboard and mouse device to wake up from S3/S4/S5. This function is supported when EUP Function is set as [Disabled]. USB S3/S4 Wakeup The optional settings: [Enabled]; [Disabled]. Use this function to enable or disable USB device to wake up from S3/S4. This function is supported when EUP Function is set as [Disabled].
► CPU Configuration Press [Enter] to view current CPU information and make settings for the following sub-items: Limit CPUID Maximum The optional settings: [Enabled]; [Disabled]. Set as [Disabled] for Windows XP. Execute Disable Bit The optional settings: [Enabled]; [Disabled]. Intel Virtualization Technology The optional settings: [Enabled]; [Disabled]. When set as [Enabled], a VHM can utilize the additional hardware capabilities provided by Vanderpool Technology. Hardware Prefetcher Use this item to turn on/off the middle level cache (L2) streamer prefetcher. The optional settings: [Enabled]; [Disabled]. Adjacent Cache Line Prefetch Use this item to turn on/off prefetching of adjacent cache lines. The optional settings: [Enabled]; [Disabled].
32
► SATA Configuration Press [Enter] to make settings for the following sub-items: SATA Controller(s) Use this item to enable or disable SATA device. The optional settings: [Enabled]; [Disabled]. SATA Mode Selection Use this item to determine how SATA controller(s) operate. The optional settings are: [IDE]; [AHCI]. *When set as [IDE], user can make further settings in ’ IDE Legacy / Native Mode Selection’ IDE Legacy / Native Mode Selection The optional settings are: [Native]; [Legacy]. For SATA device support Legacy OS (Like Dos), Please select [Legacy] for compatible. *When set as [AHCI], user can also make further settings for each available SATA (1/2) port or MINISATA port: Serial ATA Port 1/2/mSATA (Serial ATA Port 1/2/mSATA) Port Support Use this item to enable or disable each SATA port. The optional settings: [Disabled]; [Enabled]. (Serial ATA Port 1/2) Hot Plug Use this item to designate this port as Hot Pluggable. The optional settings: [Disabled]; [Enabled].
► PCH-FW Configuration Press [Enter] to go to ‘Firmware Update Configuration’ to enable or disable ‘ME FW Image Re-Flash ‘function.
► USB Configuration Press [Enter] to make settings for the following sub-items: Legacy USB Support The optional settings are: [Enabled]; [Disabled]; [Auto]. [Enabled]: To enable legacy USB support.
33
[Auto]: To disable legacy support if no USB devices are connected. [Disabled]: to keep USB devices available only for EFI specification, EHCI Hand-off This is workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. The optional settings are: [Disabled]; [Enabled]. USB Mass Storage Driver Support The optional settings are: [Disabled]; [Enabled]. Port 60/64 Emulation Use this item to enable I/O 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USWB aware OSes. The optional settings are: [Disabled]; [Enabled]. USB hardware delays and time-outs: USB transfer time-out Use this item to set the time-out value for control, bulk, and interrupt transfers. The optional settings are: [1 sec]; [5 sec]; [10 sec]; [20 sec]. Device reset time-out Use this item to set USB mass storage device start unit command time-out. The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec]. Device power-up delay Use this item to set maximum time the device will take before it properly reports itself to the host controller. The optional settings are: [Auto]; [Manual]. ‘Auto’ uses default value: for a root port it is 100 ms, for a hub port the delay is taken from hub descriptor. Select [Manual] you can set value for the following sub-item: Device Power-up delay in seconds, the delay range in from 1 to 40 seconds, in one second increments.
► Super I/O Configuration Press [Enter] to make settings for the following sub-items: Super IO Configuration ► Serial Port 1 Configuration Press [Enter] to make settings for the following items: Serial Port
34
Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. Transmission Mode Select The optional settings are: [RS422]; [RS232]; [RS485]. Serial Port FIFO Mode The optional settings are: [16-Byte FIFO]; [32-Byte FIFO]; [64-Byte FIFO]; [128-Byte FIFO]. ► Serial Port 2 Configuration/Serial Port 3 Configuration / Serial Port 4 Configuration/Serial Port 5 Configuration/Serial Port 6 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. Serial Port FIFO Mode The optional settings are: [16-Byte FIFO]; [32-Byte FIFO]; [64-Byte FIFO]; [128-Byte FIFO]. ► Parallel Port Configuration Press [Enter] to make settings for the following items: Parallel Port Configuration Parallel Port Use this item to enable or disable parallel port (LPT/LPTE). Change Settings Use this item to select an optimal setting for super IO device. Device Mode Use this item to change the printer port mode. The optional settings are: [STD Printer Mode]; [SPP Mode]; [EPP 1.9 and SPP Mode]; [EPP 1.7 and SPP Mode]; [ECP Mode]; [ECP and EPP 1.9 Mode]; [ECP and EPP 1.7 Mode]. WatchDog Timer Use this item to enable or disable WatchDog Timer Control. When set as [Enabled], the following sub-items shall appear:
35
WatchDog Timer Value User can set a value in the range of 4 ~255. WatchDog Timer Unit The optional settings are: [Min.]; [Sec.]. ATX Power Emulate AT Power This item will show current AT Mode is enabled or disabled. *Note: User needs to reset the system for the settings to take effect after setting Pin 1-2 of AT_MODE jumper as closed. Case Open Detect Use this item to detect case has already open or not, show message in POST. The optional settings are: [Disabled]; [Enabled].
► PC Health Status Press [Enter] to view current PC health status and make settings for: Shutdown Temperature Use this item to select system shutdown temperature. The optional settings are: [Disabled]; [70C/158F]; [75C/164F] [80C/172F]; [85C/180F]; [90C/188F].
► SmartFAN Configuration Press [Enter] to make settings for SmartFan Configuration: SmartFAN Configuration CPUFAN Type The optional settings are: [4 pin]; [3 pin]. SYSFAN1 Type The optional settings are: [4 pin]; [3 pin]. SYSFAN2 Type SYSFAN2 only support [4 pin] type. *Note: ‘Smart Mode’ is not supported when the [3 pin] type is selected. CPUFAN / SYSFAN1/SYSFAN2 Smart Mode When set as [Enabled], the following sub-items shall appear: CPUFAN / SYSFAN1/SYSFAN2 Full-Speed Temperature Use this item to set CPUFAN/SYSFAN1/SYSFAN2 full speed temperature. Fan will run at full speed when above this temperature.
36
CPUFAN / SYSFAN1/SYSFAN2 Full-Speed Duty Use this item to set CPUFAN/SYSFAN1/SYSFAN2 full speed duty. Fan will run at full speed when above the pre-set duty. CPUFAN / SYSFAN11/SYSFAN2 Idle-Speed Temperature Use this item to set CPUFAN/SYSFAN1/SYSFAN2 idle speed temperature. Fan will run at idle speed when below this temperature. CPUFAN / SYSFAN1/SYSFAN2 Idle-Speed Duty Use this item to set CPUFAN/SYSFAN1/SYSFAN2 idle speed duty. Fan will run at idle speed when below the pre-set duty.
► CPU PPM Configuration Press [Enter] to make settings for CPU PPM Configuration: CPU PPM Configuration: EIST Use this item to enable or disable Intel SpeedStep. CPU C3 Report Use this item to enable or disable CPU C3 (ACPI C2) report to OS. CPU C6 Report Use this item to enable or disable CPU C6 (ACPI C3) report to OS.
37
3-8 Chipset Menu
► PCH-IO Configuration
Press [Enter] to make settings for the following sub-items: ► USB Devices Configuration Press [Enter] to further setting USB device configuration. EHCI1/EHCI2 Use this item to control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. Onboard LAN1 Device/ Onboard LAN2 Device Use this item to enable or disable onboard LAN device. Azalia Use this item to control the detection of the Azalia HD Audio device.
38
The optional settings are: [Disabled]; [Enabled];[Auto]. [Disabled]: Azalia will be unconditionally disabled; [Enabled]: Azalia will be unconditionally enabled; [Auto]: Azalia will be enabled if present, disabled otherwise. Azalia Internal HDMI Codec Use this item to enable or disable internal HDMI codec for Azalia. The optional settings are: [Enabled]; [Disabled]. Restore AC Power Loss Use this item to select AC power state when power is re-applied after a power failure. The optional settings are: [Power Off]; [Power On]; [Last State].
► System Agent (SA) Configuration Press [Enter] to go for further settings: ► Graphics Configuration Press [Enter] to make further settings for Graphics Configuration. Graphics Configuration Primary Display Use this item to select which of the IGFX/PCI-E graphics device should be the primary display. The optional settings are: [Auto]; [IGFX]; [PCI-E]. Internal Graphics The optional settings are: [Auto]; [Disabled]; [Enabled]. GTT Size The optional settings are: [1MB]; [2MB]. Aperture Size The optional settings are: [128MB]; [256MB]; [512MB]. DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used by the internal graphics device. The optional settings are: [32M]; [64M]; [128M]; [256M]; [512M]; [1024M]. DVMT Total Gfx Mem Use this item to select DVMT 5.0 total graphics memory size used by the internal graphics device.
39
The optional settings are: [128M]; [256M]; [MAX]. LCD Control Primary IGFX Boot Display Use this item to select the video device which will be activated during POST. This has no effect if external graphics present. 'Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. The optional settings are: [VBIOS Default]; [CRT]; [HDMI]; [LVDS1]. *When set as [CRT]; [HDMI]; or [LVDS1], the following sub-item shall appear: Secondary IGFX Boot Display The optional settings are: [Disabled]; [CRT]; [HDMI]; [LVDS1]. Active LFP The optional settings are: [Disabled]; [Enabled]. [Disable]: VBIOS does not enable LVDS. [Enable]: VBIOS enable LVDS driver by integrated encoder. LVDS1 Panel Type Use this item to select LVDS panel resolution used by internal graphics device by selecting the appropriate setup item. The optional setting are: [640 x 480]; [800 x 480]; [800x 600]; [1024 x 600]; [1024 x 768]; [1280 x 800]; [1280 x 1024]; [1366 x 768]; [1440 x 900]; [1400 x 1050]; [1600 x 900]; [1600 x 1200]; [1680 x 1050]; [1920 x 1080]; [1920 x 1200]; [2048 x 1536]. Backlight Control The optional settings are: [PWM Inverted]; [PWM Normal]. Panel Color Depth Use this item to select the LVDS Panel Color Depth. The optional settings are: [18 Bit]; [24 Bit].
► Memory Configuration Press [Enter] to view current memory configuration, or make settings for the following sub-items: DIMM profile Use this item to select DIMM timing profile that should be used. The optional settings are: [Default DIMM profile]; [Custom profile].
40
Memory Frequency Limiter Use this item to set maximum memory frequency selection in Mhz. The optional settings are: [Auto]; [1067]; [1333]. *Note: This option is only available for settings when ‘DIMM Profile’ is set as [Default DIMM profile]. ► Custom Profile Control User can press [Enter] to make customized settings for ‘DIMM Profile’. *Note: This option is only available for settings when ‘DIMM Profile’ is set as [Custom profile]. NMode Support The optional settings are: [Auto]; [1N Mode]; [2N Mode]. Memory Remap Use this item to enable or disable memory remap above 4G. The optional settings are: [Enabled]; [Disabled].
41
3-9 Boot Menu
Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. Bootup Numlock State Use this item to select keyboard numlock state. The optional settings are: [On]; [Off]. Quiet Boot The optional settings are: [Enabled]; [Disabled]. Fast Boot The optional settings are: [Enabled]; [Disabled]. When set as [Enabled], user can make settings in the following items that appear:
VGA Support The optional settings are: [Auto]; [EFI Driver].
42
*When set as [Enabled], it will only install Legacy OpROM with Legacy OS and logo will not be shown during POST. EFI driver will still be installed with EFI OS. USB Support The optional settings are: [Disabled]; [Full Initial]; [Partial Initial]. PS2 Device Support The optional settings are: [Disabled]; [Enabled]. The PS2 devices will be skipped if this is set as [Disabled]. Network Stack Driver Support The optional settings are: [Disabled]; [Enabled]. Network Stack Driver will be skipped if this is set as [Disabled].
Boot Option Priorities Boot Option #1/ Boot Option #2/… Use this item to decide system boot order from available options.
► CSM parameters Press [Enter] to make settings for the following sub-items: Boot option filter This option controls what device system can boot to. The optional settings are: [UEFI and Legacy]; [Legacy only]; [UEFI only]. Launch PXE OpROM Policy This option controls the execution of UEFI and Legacy PXE OpROM. The optional settings are: [Do not launch];[UEFI only]; [Legacy only]; [Legacy first];[UEFI first]. Launch Storage OpROM policy This option controls the execution of UEFI and Legacy Storage OpROM. The optional settings are: [Do not launch];[UEFI only]; [Legacy only]; [Legacy first];[UEFI first]. Launch Video OpROM policy This option controls the execution of UEFI and Legacy Video OpROM. The optional settings are: [Do not launch];[UEFI only]; [Legacy only]; [Legacy first];[UEFI first]. Other PCI device ROM priority This item is for PCI devices other than Network, Mass storage or video defines
43
which OpROM to launch. The optional settings are: [UEFI OpROM]; [Legacy OpROM].
3-10 Security Menu
Administrator Password This item allows user to set administrator password. User Password This item allows user to set user password.
44
3-11 Save & Exit Menu
Save Changes and Exit This item allows user to exit the system after saving the changes. Discard Changes and Exit This item allows user to exit the system without saving any changes. Restore Defaults Use this item to restore /load default values for all the setup options. Save as User Defaults Use this item to save the changes done so far as user defaults. Restore User Defaults Use this item to restore defaults to all the setup options.