8/10/2019 Technical Datasheet Alfacoat PF4 Bitumenpaint

1/2

10, Bukit Batok Crescent | #04-04 The Spire | Singapore 658079. T +65 63372735 | F +65 63372734. E sales@benzeneinternational.com | E benzene@starhub.net.sg | W www.benzeneinternational.com

Every care has been taken in the preparation of this information. To the extent permitted by applicable law, all warranties and/or representations, express or implied, as to the accuracy of the

information are disclaimed, and no liability is accepted for the accuracy or completeness of the same. 2003 Benzene International Pte Ltd .The Benzene International logotype (and any other

trademarks) are trademarks of Benzene International Pte Ltd or one of its subsi diaries.

TECHNICAL DATA SHEET

ALFA COAT PF4 BITUMEN PAINT

Description

Alfa Coat 4 Bitumen Emulsion is a single-pack, fibrated and stable water-borne emulsion which cures to

form a firm and flexible bitumen waterproofing membrane. Alfa Coat 5 is designed for use on horizontal

and vertical surface. Alfa Coat 5 is suitable for use as waterproof membrane on concrete, asbestos

cement, roofing felt, mastic asphalt, slates, tiles and metal surface.

Technical Data

PROPERTY STANDARD

Type of solvent Petroleum Hydrocarbon

Solid Content >50%Specific Gravity 0.90

Flash Point 36 C

Film Thickness wet : 100 microns; dry : 54 microns

Application Temperature Range 5C to 55C

Drying Time BS3416/6949:1991 About 1 hour, depending

Finish BS3416/6949:1991 Smooth, opaque and free from

sags or runs.

Tap Water immersion resistance BS3416/6949:1991 Passed

Artificial Sea Water Immersion Resistance BS3416/6949:1991 Passed

Blending Resistance BS3416/6949:1991 Passed.

Effect on Portable Water BS3416:1991/BS6920:2000 Passed. Suitable for use

in contact with portable water.

Application

Surface Preparation

All surfaces shall be clean and free from dust, dirt, oil, grease, moss and loose material.

Coating Application

Apply a minimum of two thin coats by brush, roller or conventional spray equipment. Allow first coat to

dry before applying second coat at right angles to the first coat. When used as the primer, apply only

one coat and allow drying.

CoverageCoverage rates will vary depending on the actual surface environment and application. The typical

coverage is about 1.5 litres/m2 for a 2 coats of application.

Packing

Alfa Coat 4 Bitumen Paint- 18 & 200 litres

(Note: Please confirm with Benzene International Pte Ltd, Singapore for productavailability.)

8/10/2019 Technical Datasheet Alfacoat PF4 Bitumenpaint

2/2

10, Bukit Batok Crescent | #04-04 The Spire | Singapore 658079. T +65 63372735 | F +65 63372734. E sales@benzeneinternational.com | E benzene@starhub.net.sg | W www.benzeneinternational.com

Every care has been taken in the preparation of this information. To the extent permitted by applicable law, all warranties and/or representations, express or implied, as to the accuracy of the

information are disclaimed, and no liability is accepted for the accuracy or completeness of the same. 2003 Benzene International Pte Ltd .The Benzene International logotype (and any other

trademarks) are trademarks of Benzene International Pte Ltd or one of its subsi diaries.

Health and safety

Flammability:Flammable. Keep away from sources of ignition including pilot lights and sparks.

Take precautionary measures against static discharge. Do not smoke. Keep containers tightly

closed when not in use. If used in an enclosed space, ensure thorough ventilation of the area(using flame proof mechanical blowers) to avoid any accumulation of vapour until the product

has dried. In case of fire Please use dry powder, carbon dioxide, foam, sand or earth. Never use

water as this may spread the fire.

(Note: Electric motors, light/power switches and steel tools may generate sparks

sufficient to ignite such a material or the vapours given off, resulting in an explosion and/or fire.)

Skin Contact:Contains solvents which cause irritation of the skin and, in extreme circumstances,

dermatitis. Avoid contact by careful working and use of barrier cream or gloves. Remove skin

contamination with a proprietary hand cleaner following by washing

with soap and water.

Eye Contact:Could be harmful. Wear protective eye-shields, especially where there is a danger

of splashing. In the event of accidental contact, irrigate the eyes immediately with clean waterfor 15 minutes and seek medical attention.

Cleaning of Tools

Clean immediately after use with water. Use kerosene or white spirit if the material has dried. During

work, place tools in water when not in use.

Oral Digestion:With proper handling oral digestion should not occur. The possibility can be minimised

by not consuming food in the working area and by washing hands thoroughly before eating, drinking

and smoking.

Spillage:Spilt material should be mopped up immediately with an inert absorbent material such as sand

and disposed of, in accordance with local regulations, by incineration or burial.

Disposal of Containers:Do not leave empty containers on site where any residue could be a hazard to

children or animals. Replace lids and remove all containers to a central disposal point.