DynaSpec Smart Touch™

Complete Brush and Spray CARC Touch Up System

NCP® Coatings, Inc. 225 Fort St. Niles, MI 49120

Phone: 269-683-3377 Fax: 269-683-3305

www.ncpcoatings.com Rev. 1/24/13

1

Intended Uses: A multiple component kit designed to offer the end user the option of spraying for on-line application, or brushing

for off-line application CARC coatings for the repair of military vehicles and equipment painted with CARC top

coats. This kit contains two brush in cap applicators, one can of QPD listed QPL approved 1.0 VOC CARC Topcoat,

one can of HAPS Free Exempt Solvent, and one Preval® aerosol spray unit.

DynaSpec Smart Touch™ kits allow for the use of all of the material as any remaining liquid paint can be easily

utilized by plant production in normal day to day spray booths eliminating liquid waste.

Physical Properties

Colors Available:

FED-STD-595 Colors*

34094, 383 Green

33446, 686 Tan

37030, Black

33051, 383 Brown

Substrate Tested:

Previously painted substrates utilizing

QPD listed QPL approved CARC

Coatings or primer systems.

Gloss: 3.5 max @ 85º Recommended Film

Thickness: 1.8-2.2 mils dry

VOC: 1.0 lbs./gallon as packaged or

reduced with T-414. Military Specification

MIL-DTL-53039D Type VII 1.0

VOC Polymeric Flattening Agent

Application Characteristics

Mix Ratio:

Brush Use: The product may be used unreduced or reduced as desired when using the brush.

Simply shake the can of enclosed CARC material prior to use for approximately one minute or until

fully mixed, unscrew the cap and utilize one of the included brushes to apply the coating (if

reduction is desired follow the spray application guidelines for mixing prior to use). When finished

simply re-cap any remaining material with the original cap or the cap and brush combination. Note: an additional brush is included should the first one become hard or unusable for any reason. Spray Application: Start by shaking the enclosed CARC material for approximately one minute

prior to use then simply unscrew the cap from the CARC container and the enclosed solvent

container and simply add the two components to the enclosed Preval® bottle. Add the enclosed cap

and shake the combined material for approximately one minute or until completely blended. Screw

the bottle of mixed material to the Preval® power head and you are ready to spray! NOTE: SPRAY APPLICATION IS ONLY RECOMMENDED IN WELL VENTILATED AREAS SUCH AS

A CONTROLLED SPRAY BOOTH! ALL RECOMMENDED LOCAL PPE REQUIREMENTS SHOULD BE

FOLLOWED! PLEASE REFER TO THE ENCLOSED MSDS SHEETS FOR FURTHER INFORMATION

AS ATOMIZED CARC TOPCOATS CAN BE HARMFUL TO UNPROTECTED INDIVIDUALS.

Reducer: T-414 (Methyl Acetate) included

Cleaning

Solvent: Any Urethane Grade Solvent may be utilized for clean-up. NOTE: ONLY USE THE ENCLOSED T-414 SOLVENT TO REDUCE THE CARC PRODUCT (this will maintain product VOC and HAPS).

Pot Life:

12-months un-opened. Once opened CARC begins to react with the moisture in the air so it is highly

recommend that the product be utilized within an 8 hour period. For brush application the coating

life may be extended by tightly resealing the can of any unused remaining material, however

individual environmental conditions may affect the products long term stability once opened. DynaSpec Smart Touch™ kits allow for the use of all of the material as any remaining liquid paint can be

easily utilized by plant production in normal day to day spray booths eliminating liquid waste.

Dry Times: Touch: 30 minutes Recoat: Anytime Handle: 3 hrs Pack/Ship: 4 hrs

Force Cure: This product can be force cured for approximately 30 minutes at 180o F after a 20-30 minute flash off

time (product mass dependent).

Full Cure: 7 days

Note: Test Performed @ 77°°°° F 50% Relative Humidity

Tech

nica

l Data

Sheet

DynaSpec Smart Touch™

Complete Brush and Spray CARC Touch Up System

NCP® Coatings, Inc. 225 Fort St. Niles, MI 49120

Phone: 269-683-3377 Fax: 269-683-3305

www.ncpcoatings.com Rev. 1/24/13

2

Recommended Primers Substrate Recommended Primer

Aluminum MIL-PRF-23377, MIL-DTL-53022, or MIL-PRF-85582 Epoxy Primers (Consult Contract Requirements).

Aluminum/Galvanized

Steel/Stainless Steel: DOD-P-15328 or MIL-C-8514C Wash Primer (Consult Contract Requirements).

Ductile or Grey Iron Castings: MIL-DTL-53022 or MIL-DTL-53030 Epoxy Primers (Consult Contract Requirements).

Plastics: Due to the wide variety of plastic/fiberglass substrates, the system performance should be

tested and confirmed on actual substrate.

Previously Painted Surfaces:

Surface should be intact and sound. All loose and flaking material removed and bare spots primed with an appropriate primer. An area should be tested with the coating to assure

compatibility.

Steel: MIL-DTL-53022 or MIL-DTL-53030 Epoxy Primers (Consult Contract Requirements).

Wood: Due to the wide variety of wood substrates, the system performance should be tested and

confirmed on actual substrate.

Note: The above parameters are to be used as a guideline only. Customer specific equipment may require a different set-up

Surface Preparation Do not apply if the application surface temperature is below 45°F (7°C) or above 110°F (43°C), or if the surface temperature is

within 5°F of the dew point. It is highly recommended that sound practices as set forth by SSPC or NACE be followed when

preparing a substrate for painting. At a minimum the surface should be clean of all grease, dirt, oil, rust and foreign material that

would be detrimental to proper adhesion and desired performance of the coating system being applied.

Safety Precautions This product is intended for professional use in an industrial environment only! Consult the Material Safety Data Sheet prior to

application for detailed information on the health and safety hazards.

Shelf Life & Storage Conditions Shelf life (un-opened kits protected from atmospheric moisture): 12 months from the date of manufacture. This product must be stored in accordance with local, state, and national regulations. Preferred storage conditions: Keep containers in a dry space with

adequate ventilation.

Comments For additional information contact your NCP Coatings, Inc. Sales Representative, Customer Service Representative, or visit our website: www.ncpcoatings.com

Note The above information is supplied as a guideline to our customers. The user must be aware of the cleaning, pretreatment,

application and testing requirements for their specific job!

MIL-DTL-53039D TYPE VII

DynaSpec Smart Touch Paint

Part Number Part Number Color Paint QPL# Kit QPL#

N-8204ST N-8204 Tan 686 Q 1884 Q2089 N-8205ST N-8205 Brown 383 Q 1885 Q2090

N-8913ST N-8913 Green 383 Q 1941 Q2091

N-8914ST N-8914 Black Q 1942 Q2092

Tech

nica

l Data

Sheet

DynaSpec Smart Touch™

Complete Brush and Spray CARC Touch Up System

NCP® Coatings, Inc. 225 Fort St. Niles, MI 49120

Phone: 269-683-3377 Fax: 269-683-3305

www.ncpcoatings.com Rev. 1/24/13

3

Brush Application:

1. 2. 3.

Spray Application:

1. 2. 3.

4.

Comments For additional information contact your NCP Coatings, Inc. Sales Representative, Customer Service Representative, or visit our

website: www.ncpcoatings.com

Tech

nica

l Data

Sheet