supporting information for - royal society of …s1 supporting information for intense ultraviolet...
TRANSCRIPT
S1
Supporting Information for
Intense Ultraviolet Upconversion Emissions in Water-Dispersed
Colloidal YF3:Yb3+/Tm3+ Rhombic Nanodisks
Hailong Qiu,adf Guanying Chen*af, Rongwei Fan,b Liming Yang,c Cheng Liu,c Shuwei
Hao,a Michael J. Sailor, d Hans Ǻgren,e Chunhui Yang*a and Paras N. Prasad*f
aSchool of Chemical Engineering and Technology, Harbin Institute of Technology,
150001 Harbin, People’s Republic of China.
E-mails: [email protected], [email protected] bNational Key Laboratory of Tunable Lasers, Institute of Optical Electronics, Harbin
Institute of Technology, 150001 Harbin, People’s Republic of China cDepartment of Pathophysiology, Harbin Medical University, 150001 Harbin,
People’s Republic of China dDepartment of Chemistry and Biochemistry, The University of California, San Diego,
9500 Gilman Drive, La Jolla, California 92093-0358, United States eDepartment of Theoretical Chemistry, Royal Institute of Technology, S-10691
Stockholm, Sweden fInstitute for Lasers, Photonics, and Biophotonics, The State University of New York at
Buffalo, Buffalo, New York 14260, United States. E-mail: [email protected]. gDepartment of Chemistry, Korea University, Seoul 136-701, Korea
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S2
Materials All reagents were of analytical grade and used without further purification. Y2O3,
Yb2O3, and Tm2O3 (purity ≥ 99.99 %) were supplied by Beijing Founde Star Science
and Technology Co., Ltd China. Oleic acid (OA, 90%) and octadecene (ODE, 90%)
of technical grade were obtained from Sigma-Aldrich. Poly(acrylic acid) (PAA)
(Mw=1800) and diethylene glycol (DEG) were purchased from Sigma-Aldrich.
Ethanol, chloroform, cyclohexane, sodium hydroxide, perchloric acid, nitric acid, and
trifluoroacetic acid (99%) were supplied by Tianjin Chemical Reagent Company.
Deionized water was used throughout the synthesis procedure.
Synthesis of YF3:Yb3+/Tm3+ Rhombic Nanodisks. YF3:Yb3+/Tm3+ rhombic
nanodisks codoped with 2 mol% Tm3+ and 10, 30, 50, 70, 90 and 98 mol% Yb3+ were
synthesized using a thermolysis method adapted from our recent work. In a typical
procedure, 1 mmol lanthanide oxides (Tm2O3, Yb2O3, and Y2O3) were dissolved in
50% concentrated trifluoroacetic acid at 95 °C in a three-necked 100 mL flask. The
molar ratios of the cationic ions of precursors were [Tm/(Tm+Yb+Y)] =0.02, and
[Yb/(Tm+Yb+Y)]=0.10, 0.30, 0.50, 0.70, 0.90 and 0.98, for nanodisks of YF3 doped
with 2 mol% Tm3+ and 10, 30, 50, 70, 90 and 98 mol% Yb3+, respectively. Then, the
solutions were evaporated to dryness under N2 gas purge. Next, 10 mL of OA and 10
mL ODE were added into the three-necked flask. The resulting solution was heated at
140 °C for 45 min, and then to 320 °C at a rate of about 18 °C/min. The reaction was
kept at this temperature for about 1 h per min under N2 gas protection. A needle was
used to let the N2 gas out during the synthesis. After cooling down to room
temperature, the resulting products were precipitated by ethanol and collected by
centrifugation at 5000 rpm for 5 min. The precipitate was then purified with ethanol
three times, and finally dispersed in cyclohexane or chloroform for further uses.
Ligand Exchange of the Oleic Acid with the Polyacrylic Acid. The ligand exchange
procedure is adapted from a literature work.S1,S2 In a typical procedure, a mixture of
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S3
DEG (8.0 mL) and PAA (0.1 g) was heated to 110 °C with vigorous stirring under N2
flow. Then, 2 mL chloroform solution of YF3:Yb3+/Tm3+ rhombic nanodisks (50
mg/mL) were injected and the system was heated to 240 °C for 5 min. During this
process, the initial milky solution gradually became clear. After cooling to room
temperature, an excess of diluted hydrochloric aqueous solution was added in into the
solution until a white precipitation is seen. The precipitation was collected by
centrifugation, washed three times with pure water, and neutralized with a diluted
solution of sodium hydroxide. Finally, the YF3:Yb3+/Tm3+ nanodisks are dispersed in
deionized water.
Characterization
X-ray Diffraction. The powder X-Ray diffraction (XRD) pattern was carried out on a
Rigaku D/max-γB diffractometer equipped with a rotating anode and a Cu Kα source
(λ=0.15418 nm). The 2θ angle of the XRD spectra was recorded at a scanning rate of
5 °/min from 20° to 90°.
Transmission Electron Microscopy. The morphology and size of the resulting
nanoparticles were investigated by means of transmission electron microscope (TEM,
Tecnai G2 Spirit Twin 12) operating at 80 kV. High resolution transmission electron
microscopic (HRTEM) images were obtained on the microscope of Spirit Twin Tecnai
G2 D339 operating at 300 kV. One drop of diluted colloidal YF3 solution dispersed in
cyclohexane or water was allowed to be dried on the surface of the carbon-coated
copper grid.
Fourier Transform Infrared Spectra. Fourier transform infrared (FT-IR) spectra
were measured on an IRPRESTIGE-21 spectrometer utilizing the potassium bromide
(KBr) pellet technique. To make the KBr pelletes, 1 mg of YF3 nanoparticles were
mixed with approximately 100 mg KBr powder. The FT-IR spectrum was collected in
the spectral range of 400-4000 cm-1.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S4
Upconversion Spectra. Upconversion spectra UC PL spectra were recorded using a
lens-coupled monochromator (Zolix Instruments Co. Ltd., Beijing) with a slit width
defining spectral resolution of 2 nm. The emissions were excited at 980 nm using a
fiber-coupled laser diode (Hi-Tech Optoelectronics Co. Ltd., Beijing). All
measurements were performed at room temperature, preserving the same geometry
for the upconversion luminescence recording. Photographic images of colloidal
nanocrystals YF3:Yb3+/Tm3+ were taken by a digital camera (Canon Power Shot
SX100 IS) without adding any filter.
Inductively Coupled Plasma Atomic Emission Spectra. The composition of the
resulting nanoparticles was determined by an inductively coupled plasma atomic
emission spectroscopy (ICP-AES) (VistaPro, Varian). The samples (200 μL, 5mg/mL)
were firstly dissolved in concentrated perchloric acid (2 mL) at 80 °C for 6 h. Then,
the solutions were diluted with 1% HNO3 to a volume of 10 mL.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S5
0 5 10 15 20 25 30 35 40 45 50
Nano
parti
cles
Cou
nts
Diameter (nm)
YF3 Gauss Fitting
Figure S1. Histogram of the side length of rhombic nanodisks of YF3 codoped with
10 mol% Yb3+ and 2 mol% Tm3+. These data were obtained from the TEM images of
more than 200 nanoparticles. The average side length of rhombic nanodisks was
determined be ~14.3 nm with a standard deviation of 1.0 nm.
500 1000 1500 2000 2500 3000 3500 40000
50
100
150
200
250
300
17333422
1600
1432 1706
Inte
nsity
(a.u
.)
Wavelength (cm-1)
a
b2927
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S6
Figure S2. Fourier transform infrared (FTIR) spectra of YF3 rhombic nanodisks
before (a) and after (b) ligand exchange with ployacrylic acid (PAA). The bands at
1432 and 1600 cm-1 in Figure S2(a) arise from the ansymmetric and symmetric
vibration modes of the -COOH group, respectively, indicating the adsorption of OA
on the nanodisk surface through a bidentate bond. The intensities of these two bands
become weaker after ligand exchange in Figure S2 (b). The weak stretching mode of
the -COOH group at 1706 cm-1 in Figure S2(a) suggests the presence of trace amount
of free oleic acid on the surface of rhombic nanodisk. However, this band is enhanced
and shifted to 1732 cm-1 after ligand exchange with PAA (Figure S2 (b)), suggesting
an increase in the number of -COOH groups. Additionally, the shoulder at 2927
cm-1, associated with the asymmetrical stretching mode of -CH3 group, became
weaker after ligand exchange, showing that the number of the -CH3 groups is reduced
on the nanodisk surface after ligand exhange. The broad band at 3100-3600 cm-1
arises from the O-H stretching vibration of -COOH group in Figure S2 (a), which
becomes much stronger in Figure S2 (b). Since the PAA ligands have abundant
COOH groups, the increased number of COOH group confirms that PAA have been
introduced onto the nanodisk surface. These observations give a strong evidence of
the successful exchange of OA with PAA.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S7
Figure S3. Energy level diagrams of Yb3+ and Tm3+ ions as well as the proposed
upconversion mechanisms for different emission bands (λex= 980 nm). The Yb3+ ions
firstly absorbs laser photons at ~980 nm, and are excited from the ground state 2F5/2 to
the 2F7/2 state. Then, the Yb3+ ions in their excited states successively transfer the
absorbed energy to the Tm3+ ion, and promote it from the ground sate to the 3H5 (first
step), 3F2,3 (second step), 1G4(third step), 1D2(fourth step), and 3P1(fifth step) states,
respectively. Multi-phonons from the lattice are involved to assist the energy transfer
from Yb3+ to Tm3+ ions. Nonradiative relaxations from the 3F2,3 state can populate
the 3H4 state, from which the near infrared (NIR) emission at 800 is produced. It
should be noted that the cross-relaxation process of 1G4+3F4→3H4+3F2 can contribute
to populate the 3H4 state, thus might leading to slightly larger photon process than 2
for NIR emission at 800 nm. In addition, nonradiative relaxations from the 3P1 state
can populate the 1I6 state, from which ultraviolet (UV) emission at 290 and 345 nm
can be generated by radiative relaxations to the ground state 3H6 and the first excited
state of 3F4, respectively. The upconversion emissions at 360 and 450 nm arise from
radiative relaxations from the 1D2 state to the ground 3H6 and the excited state of 3F4
of Tm3+ ions, respectively. The blue emission at 475 nm stems from radiative
relaxations from the 1G4 state to the ground 3H6 state.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S8
10 20 30 40 50 60 70 800
2000
4000
6000
8000
10000
12000
14000
16000i
h
g
f
e
d
c
b
YF3:98%Yb/2%Tm
YF3:90%Yb/2%Tm
YF3:70%Yb/2%TmYF3:50%Yb/2%Tm
YF3:30%Yb/2%Tm
2θ (degree)
Inte
nsity
(a.u
.)
YF3-70-1935
YbF3-49-1805
YF3:10%Yb/2%Tm
YF3
a
(131)
Figure S4. XRD patterns of (a) standard data of orthorhombic YF3 (JCPDS Card No.
70-1935), (b) standard data of orthorhombic YbF3 (JCPDS Card No. 49-1805), as
well as rhobmbic nanodisks of (c) pure YF3 (without doping), (d) YF3:10
mol%Yb3+/2 mol%Tm3+ (e) YF3:30 mol%Yb3+/2 mol%Tm3+, (f) YF3:50 mol%Yb3+/2
mol%Tm3+ (g) YF3: mol%Yb3+/2 mol%Tm3+ (h) YF3:90 mol%Yb3+/2 mol%Tm3+,
and (i) YF3:98 mol%Yb3+/2 mol%Tm3+.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S9
Figure S5. TEM images of rhobmbic nanodisks of YF3:10 mol%Yb3+/2 mol%Tm3+
(left) before and (right) after ligand exchange.
Figure S6. TEM images of rhobmbic nanodisks of YF3:30 mol%Yb3+/2 mol%Tm3+
(left) before and (right) after ligand exchange.
Figure S7. TEM images of rhobmbic nanodisks of YF3:50 mol%Yb3+/2 mol%Tm3+
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S10
(left) before and (right) after ligand exchange.
Figure S8. . TEM images of rhobmbic nanodisks of YF3:70 mol%Yb3+/2 mol%Tm3+
(left) before and (right) after ligand exchange.
Figure S9. . TEM images of rhobmbic nanodisks of YF3:90 mol%Yb3+/2 mol%Tm3+
(left) before and (right) after ligand exchange.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S11
Figure S10. . TEM images of rhobmbic nanodisks of YbF3: 2 mol%Tm3+ (left)
before and (right) after ligand exchange.
Figure S11. Room temperature upconversion emission spectra of (a) YF3: 10
mol%Yb3+/2 mol%Tm3+ core and YF3: 10 mol%Yb3+/2 mol %Tm3+@YF3 core/shell
nanoparticles, and (b) YF3: 10 mol %Yb3+/2 mol%Tm3+@YF3 and YF3: 90
mol %Yb3+/2 mol%Tm3+@YF3 core/shell nanoparticles.
The increase of Yb3+ ions can produce two distinct effects on the upconversion
emissions. (i) Enhancing upconversion emission intensities due to elevated energy
transfers from Yb3+ to Tm3+ ions; (ii) Quenching upconversion emission intensities
due to Yb3+ sublattice-mediated energy transfer of excitation energy to nanoparticle
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S12
surface quenching centers. The quenching mechanism, however, can be eliminated or
effectively suppressed by growing an inert shell layer on the particle surface. Hence,
to confirm our proposed enhancement mechanism for Fig.4, we have prepared
core/shell structure nanoparticles of YF3:10 mol %Yb3+/2 mol %Tm3+@YF3 and YF3:
90 mol%Yb3+/2 mol%Tm3+@YF3, wherein the quenching mechanism induced by
Yb3+ ion has been suppressed. Figure S11 displays upconversion emission spectra of
(a) YF3: 10 mol%Yb3+/2 mol%Tm3+ core and YF3: 10 mol%Yb3+/2 mol%Tm3+@YF3
core/shell nanoparticles, as well as (b) YF3:10 mol%Yb3+/2 mol%Tm3+@YF3 and
YF3:90 mol%Yb3+/2 mol%Tm3+@YF3 core/shell nanoparticles. In comparison to the
emission intensity of core nanoparticles of YF3: 10 mol%Yb3+/2 mol%Tm3+, the
emission intensity in the YF3: 10 mol%Yb3+/2 mol%Tm3+@YF3 core/shell
nanoparticles is significantly increased, indicating the successful growth of an YF3
layer on the surface of core nanoparticles [Figure S11 (a)]. Moreover, in Figure S11
(b), it is shown that UV upconversion emission in YF3:90 mol%Yb3+/2
mol%Tm3+@YF3 core/shell nanoparticles is about 5 times higher than that of the
YF3:10 mol%Yb3+/2 mol%Tm3+@YF3 nanoparticles, clearly substantiating our
proposed mechanism in this work.
Table S1. Compositions of these nanodisks of YF3 codoped with 2 mol% Tm3+ and
10-98 mol% Yb3+. These compostions are determined by inductively coupled plasma
atomic emission spectroscopy (ICP-AES). The measured atomic ratios are in good
agreement with the ratios of precursors that are employed for nanoparticle synthesis.
Sample The mole ration of doped [Ln3+] in NCs (at. %) [Y3+] : [Yb3+] : [Tm3+]
YF3:10%Yb3+/2%Tm3+ 86.45 : 11.43 : 2.12 YF3:30%Yb3+/2%Tm3+ 67.30 : 29.89 : 2.81 YF3:50%Yb3+/2%Tm3+ 48.23 : 50.07 : 1.70 YF3:70%Yb3+/2%Tm3+ 28.93 : 69.09 : 1.98 YF3:90%Yb3+/2%Tm3+ 08.63 : 89.26 : 2.11 YF3:98%Yb3+/2%Tm3+ 00.00 : 97.32 : 2.68
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013
S13
Reference:
S1. T. Zhang, J. Ge, Y. Hu and Y. D. Yin, Nano Lett., 2007, 7, 3203.
S2. H. L. Qiu, G. Y. Chen, L. Sun, G. Han, C. H. Yang, J. Mater. Chem., 2011, 21, 17202.
Electronic Supplementary Material (ESI) for NanoscaleThis journal is © The Royal Society of Chemistry 2013