state bank of india administrative office zone … 2 of 15 tender form the, chief manager [gb] state...

of 15

TENDER DOCUMENT

STATE BANK OF INDIA

Administrative Office Zone –I

Bull Temple Road

Bangalore-19

Name of Work: ‘’ PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED S.B.I.RACPC AT

YALAHANKA NEW TOWN AT PRESTIGE TOWER, OUTER RING ROAD YALAHANAKA BANAGLORE ‘’

LAST DATE OF SUBMISSION:

ON OR BEFORE 03.00 PM

LAST DATE OPENING:

23.06.2017 At 03.30 PM

Chief Manager [GB]

of 15

TENDER FORM

The,

Chief Manager [GB]

State Bank of India

Administrative Office, Zone –I

Bangalore-4

Dear Sir,

1. Having examined the tender documents contained thereby relating to the words specified in. The

memorandum herein after set out and having visited the examined the source of works specified in the said

memorandum and having acquired the requisite information relating thereto affecting the tender. I / We

hereby offer to execute the works specified in the said memorandum at the rates mentioned in the bill of

quantities hereto and in accordance with all respects of specifications, and instructions in writing referred to

in the tender notice, General Conditions of contract, Schedule of quantities in all other respects accordance

with such conditions so far as they may be applicable.

MEMORANDUM

2. Date of commencement : within 7 days from the date of work order or

Letter of intent

3. Period of completion : 30 days from the date of issue of work order

4. Defects liability period : 6 months from the date of virtual

Completion & submission/payment

Of final bill

5. Liquidated damages [penalty] : ½% per week subject to max of 5%

6. Supplier before quoting should compulsorily make a site visit and understand the work to be done

7.Should the tender be accepted, I/ we hereby agree to abide and fulfill the terms and provisions of the said

conditions of contract.

of 15

NOTICE INVITING TENDER

1. Sealed item rate tender for ‘’ PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED

S.B.I.RACPC AT YALAHANKA NEW TOWN AT PRESTIGE TOWER , OUTER RING ROAD YALAHANAKA

BANAGLORE ‘’

2. Tenderer is advised to go through all the documents in connection with this contract carefully.

3. Tenderer shall deposit the sealed tender in the Office of The Chief Manger [GB] State Bank Of India

Administrative Office Zone –I Bull Temple Road Bangalore - 4 Tenderer shall deposit the sealed envelopes

separately containing the following

PART ‘B’

1. Schedule of quantities duly filled in figures and words and signed on each page with seal and date

Tenders will be received up to A.M. On and shall be opened on the same day @

At the Office of The Regional Business office –I administrative office Zone -I STATE BANK

OF INDIA, Administrative Office Bangalore-4. Tenders received after fixed time and date due to postal

delay will not be considered.

2. Tenders not properly filled, mutilated with incorrect calculations or generally not complying with

conditions will be rejected.

3. Tenderer should quote their rates both in figures and in words. The Schedule of quantities must be fully

priced with rates quoted for both unit rate specification and the total of each page along with carried

over figures of previous page shall be given in ink and signed by the Tenderer. No blank space shall be

left. Figures in words shall be deemed to be final figures, in case of cuttings or over writings. However, it

is essential that the contractor should ensure that he has signed on all pages of the tender document.

4. PERIOD OF VALIDITY

The tender shall remain valid for acceptance of a period of 90 days from the date of submission of tenders.

If any Tenderer with draw his tender before the said period or make any modifications in the terms and

conditions of the tender, then the employer has the liberty to disqualify the Tenderer

Every Tenderer is expected to inspect the site of the proposed work and acquaint him with site conditions,

approaches, availability of the raw materials, geological and weather conditions etc. before quoting his rates.

He must go through all the specifications, and other tender documents. Any further clarifications in the

documents can be had from this Office at the above mentioned address.

5. QUANTUM OF WORK

of 15

A schedule of probable quantities in respect of each work and specifications accompany these conditions.

The schedule of probable quantities is liable to alterations, omissions or additions at the discretion of the

Bank. The schedule of the probable quantities may vary considerably on the higher or lower side.

6. ALL INCLUSIVE RATES

Quoted Rate shall include the cost of transportation of material to the site, all taxes such as sales tax, excise

duty, octroi, works contract and any other statutory levy, etc. and fixing or placing in position for which the

item of work is intended to be operated. The rates quoted by the contractor shall be firm throughout the

contract period and there shall be no upward revision of the rates. It should be clearly understood that any

claims for extra sales tax, excise duty, octroi, works contract and any other statutory levy, etc shall not be

entertained in any case whatsoever once tenders are opened.

11. INTERPRETING SPECIFICATIONS

In interpreting specifications, the following order of decreasing importance shall be followed:

1. Schedule of quantities with detail specifications

2. Unit rate specifications and technical specifications

3. General Specifications

Matters not covered by the specifications given in the contract, as a whole shall be covered by the relevant

Indian standard codes. If such a Codes on a particular subject have not been framed, the decision of the Bank

Engineer shall be final.

12. The acceptance of the tender shall rest with the authorized representative of the employer, who does not

bind himself to accept the lowest tender and reserves to himself the authority to reject any or all the tenders

received without assigning any reasons, whatsoever.

13. The work shall be carried out under the direction and supervision of the Bank Engineer or their

representative at site. On acceptance of the tender, the contractor shall intimate the name of his accredited

representative who would be supervising the work and would be responsible for taking instructions for carrying

out the work.

14. Bank Engineer decision with regard to the quality of material and workmanship will be final and binding,

any material rejected by the Bank Engineer shall be immediately removed from the site by the

Contractor.

of 15

15. SUB-LETTING

No part of the contract shall be sublet without the written permission of the employer nor shall transfers be

made by the power of attorney authorizing others to carry out the work or receive payment on behalf of the

renderer.

16. DEFECTS LIABILITY PERIOD

Any defect developed within the defect liability period of 6 months will have to be rectified by the agency at

their own cost and in case and the defects are not rectified by the contractor, employer or their

representative shall get the work done at the risk and cost of the contractor.

17. CERTIFICATE OF VIRTUAL COMPLETION

The work shall not be considered as completed until the Bank has issued in writing “certificate of virtual

completion” stating that the work has been completed and defects liability period shall commence from such

certified date of virtual completion.

18. DELAYS IN COMMENCEMENT

The contractor shall not be entitled to any compensation for any loss suffered by him on account of delays in

commencing or executing the work, whatever the cause for such delays may be including delays in procuring

government controlled or other materials.

19. The contractor should inspect the source of material, their quality, quantity, and availability. The

material must strictly comply with the relevant specifications attached.

20. PERIOD OF COMPLETION

Time is deemed to be the essence of the contract; the completion period shall be twenty days. The contractor

shall draw a detailed schedule of program in the form of BAR/PERT CHART of whole work, within two weeks of

the award of the work and submit to the Bank for its approval.

21. CONTRACTORS STORE

of 15

Suitable area near the site of work shall be allowed to the contractor free of cost for storing his tools and

plants, materials and for his site office. The contractor shall remove all temporary constructions constructed

by him at site for the purpose of completing the work after the work is over

22. MEASUREMENT AND BILLING

Whenever mode of measurement is specified, measurement will be taken at site as per the latest IS code of

practice for measurement.

The contractor or his representative shall accompany the employer or their representative in taking/checking

Measurements. All necessary tapes and shall be supplied by the Contractor. The Contractor shall then

present his bill based on the agreed and recorded measurements and if the contractor fails to accompany the

employer for measurement, then he shall be bound by the Measurement s taken by the Bank Engineer

Contractor shall raise first and final bill or for minimum payment of a Running Bill

Payment towards all interim bills will be made by the employer within the time limit specified in the summary,

form of the tender

Period of final measurement shall be 30 days from the date of completion of the project.

23. WATER AND ELECTRICITY

The employer will make water supply and electricity to the site at one convenient point available. The

contractor should make his own arrangements in case of supplementary supply points are required for both

water and electricity. The consumption charges shall be borne by the contractor.

24. INSURANCE

The successful contractor shall take out the contractor’s all risk insurance policy, jointly in the name of the

employer and the contractor and the original policy shall be deposited with the employer. The insurance policy

shall be obtained within 14 days of date of commencement of the work

25. STATUTORY REGULATION

The whole work is to be complied with as per the requirements and by laws of relevant statutory authorities,

including contract labor (Regulation and Abolition) act 1970.

I/ We hereby declare that I/We read and understood the above instructions and the terms and conditions

mentioned above are binding on me/us.

PLACE:

DATE: SIGNATURE WITH SEAL

of 15

SATE BANK OF INDIA

ADMINISTARTIVE OFFICE-ZONE –I

BANGALORE

NAME OF WORK: PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED S.B.I RACPC BRANCH AT

YALAHANKA NEW TOWN, BENGALURU

TENDER SHEDULE :

Sl no Items of work Unit Qty Rate Amount

1 HIGH LEVEL PARTITION:

Providing and fabricating High level partition up to the

ceiling height by using well seasoned

Sal/Honne/Mathi/ Nandi wood of section 40 mm x 60

mm /Plain Aluminum section of size 38 mmx 63 mmx

1.5 mm spacing at 600 mm center to center vertically

and horizontally at floor, sill and at top one member

touching up to ceiling. The framework shall be

assembling with proper wooden joineries required

fevicol nails zigzag clamps at junctions. Over the

frame work 6 mm ply of approved make Regal / Uniply

/ Archid ply / Amul / Well ply shall be fixed with

headless Niles and required fevicol and required

opening shall be left to fix the Door, Glass, and shall

be fixed with glass of 8 mm thick glass with required

etched glass design, beach wood / 12 mm ply shall be

used to fix the glass and shall be laminated with 1 mm

thick, if wood beading shall be directed shall be

polished with color polish to match the laminate all

round lipping with 4 mm ply. Over the frame work 6mm

ply of grade BWP/BWR Regal / Uniply / Archid ply /

Amul / Well ply approved make shall be fixed with

required fevicol head less nails, lastly over the ply

1mm thick laminate of approved make shall be fixed

with required fevicol finished neatly etc complete.

This rate Includes cost of all materials, labor, and

taxes, lead and lift, to the place of work.

Sqmt

40.00

Rupees in words

2 LOW HEIGHT PARTITION:

Providing and fabricating low level partition up to 1.50

mt height by using well seasoned

sal/honne/mathi/champa wood of section 40 mm x 60

mm/Plain Aluminum section of size 38 mmx 63 mmx 1.5

mm at 600 mm center to center vertically and

horizontally at floor, sill and at top one member

touching up to1.5 mt ht. The framework shall be

assembling with proper wooden joineries required

fevicol nails zigzag clamps at junctions. Over the

frame work6 mm ply of approved make Regal / Uniply /

Archid ply / Amul / Well ply shall be fixed with

headless Niles and required fevicol and required

opening shall be left to fix the glass of 10 mm thick

(Cost of the shall be paid separately), the glass shall

of 15

be fixed with required Beach wood beading with 4 mm

ply all round lipping before fixing the glass / Shall be

fixed with 12 mm ply later laminated with 1 mm thick

laminate. Over the skeleton frame work 6mm ply of

approved BWP/BWR ply Regal / Uniply / Archid ply /

Amul / Well ply and make shall be fixed with required

fevicol head less nails, over the ply 1 mm thick

laminate of approved make and shade matt /suede

shall be fixed with required fevicol finished neatly etc

complete. This rate includes cost of all materials,

labor, and taxes, lead and lift, to the place of work.

Sqmt

150.00

Rupees in words

3 FLOOR PEDESTAL UNIT:

Providing and fabricating floor pedestal unit of size

0.40 mt x 0.50 mt x 0.76 mt size by using approved

make Regal / Uniply / Archid ply / Amul / Well ply

BWP/BWR block board / Ply the draw box unit will

have three no of drawer unit of size 400 x 500 x 150

mm which shall be fabricated by using full paneled

drawer sliding unit of make Ebco with 19mm block

board for the front and 12 mm thick for the bottom

draw unit. At bottom one shutter shall be fixed with

Ebco make flap/Box hinges either if one drawer

cancelled. At the bottom all cut edges of the block

board shall be fixed with beach wood beading lipping

finished neatly with color less polish front exposed

surface of unit shall be fixed with 1mm thick

lamination of approved make and shade with required

fevicol finished neatly .all hardware materials are of

standard type like stainless Steel handles of approved

make, multi lock is of Laxmi / Godrej. Inner surface of

the unit shall be painted with Enamel paint followed by

pop putty Etc complete This rate includes cost of all

materials, labor, taxes, lead and lift, to the place of

work.

No

26.00

Rupees in words

4 STORAGE CABINET HIGH LEVEL UPTO 1.52 MT HT

Providing and fabricating full height floor Storage

cabinet as per the design by using 19 mm BWP / BWR

block board / Ply of approved make. The cabinet

fabricated all round block board of 0.45/0.40 -mt

widths to form a box at rear side shall be Fixed with 9

mm thick ply. Front shall be fixed with two half

shutters according to the size of cabinet. The cabinet

will also have equal partition shelves inside. Inside and

front lipping shall be done by 6 mm ply to form the

grove .All cut edges of the block boar shall be fixed

with beach wood beading shall be polished finished

with color less polish finished neatly .All exterior

surface of the block board shall be fixed with 1mm

thick lamination with required fevicol finished neatly,

all interior surface of the block board shall be

finished with two coats of enamel paint followed by

of 15

pop putty and primer. Lastly the cabinet will get fitted

with H/D type s.s handles of size 15 cm, multi lock,

hinges, laminated Etc complete This rate includes cost

of all materials, labor, and taxes, lead and lift, to the

place of work.

Sqmt

5.00

Rupees in words

5 STORAGE CABINET LOW LEVEL UPTO 0.90 MT HT

Providing and fabricating full height floor Storage

cabinet as per the design by using 19 mm BWP / BWR

block board / Ply of approved make. The cabinet

fabricated all round block board of 0.45/0.40 -mt

widths to form a box at rear side shall be Fixed with 9

mm thick ply. Front shall be fixed with two half

shutters according to the size of cabinet. The cabinet

will also have equal partition shelves inside. Inside and

front lipping shall be done by 6 mm ply to form the

grove .All cut edges of the block boar shall be fixed

with beach wood beading shall be polished finished

with color less polish finished neatly .All exterior

surface of the block board shall be fixed with 1mm

thick lamination with required fevicol finished neatly,

all interior surface of the block board shall be

finished with two coats of enamel paint followed by

pop putty and primer. Lastly the cabinet will get fitted

with H/D type s.s handles of size 15 cm, multi lock,

hinges, laminated Etc complete This rate includes cost


place of work.

Sqmt

22.00

Rupees in words

6 SIDE CREDENZA UNIT:

Providing fabricating side credenza unit of size 1.82

mt x 0.40 mt x 0.76-mt sizes for specified areas.

The cabinet shall be fabricate by using 19 mm thick

block board /Ply , 12 mm ply, 6 mm ply, of approved

make BWP/BWR grade .The drawer unit get fitted

with full paneled metal drawer Sliding unit of make

Ebco S.S handles, multi locks. The, exterior surface of

the unit shall be fixed with 1 mm thick lamination of

approved make Mat/Suede finish with required fevicol

finished neatly, the interior surface of the unit shall

painted with two coats of enamel paint followed by

p.o.p putty and primer Etc complete This rate includes

cost of all materials, labor, and taxes, lead and lift, to

the place of work.

No

15.00

Rupees in words

7 SIDE CREDENZA UNIT:

Providing fabricating side credenza unit of size 1.40

mt x 0.40 mt x 0.76-mt sizes for specified areas.

The cabinet shall be fabricate by using 19 mm thick

block board /Ply , 12 mm ply, 6 mm ply, of approved

make BWP/BWR grade .The drawer unit get fitted

of 15

with full paneled metal drawer Sliding unit of make

Ebco S.S handles, multi locks. The, exterior surface of

the unit shall be fixed with 1 mm thick lamination of

approved make Mat/Suede finish with required fevicol

finished neatly, the interior surface of the unit shall

painted with two coats of enamel paint followed by

p.o.p putty and primer Etc complete This rate includes


the place of work.

No

15.00

Rupees in words

8 WORK STATION:

Providing and fabricating workstation of size 2.20

mtx0.76 mt x 0.76 mt deep with one side draw box

unit of size 450 mm width x500 mm deep x750mm

height comprising three no of drawer unit. The whole

unit shall be fabricated by using 19 mm thick block

board /Ply of approved make Regal / Uniply / Archid

ply / Amul / Well ply BWP/BWR grade as per the

design and drawing, exterior surface of the unit shall

be fixed with 1mm thick lamination of approved make

with required fevicol .The draw box unit get fixed

with full panel drawer sliding unit of make Ebco/Zip

co, multilocks, H/D type stainless steel handles .The

inner surface of the unit shall be painted with two

coat of primer & Enamel paint by pop putty, all cut

edges of block board shall be fixed with flat beach

wood beading finished with color less polish finished

neatly Etc complete This rate includes cost of all

materials, labor, and taxes, lead and lift, to the place

of work.

No

1.00

Rupees in words

9 WORK STATION:

Providing and fabricating workstation of size 1.82


















of work.

No

6.00

Rupees in words

of 15

10 WORK STATION:

Providing and fabricating workstation of size 1..52


















of work.

No

2.00

Rupees in words

11 L-TYPE TABLE :

Providing and fabricating and fixing the L-Type works

station of size 1.50 mt x 0.60 mt at one side and 1.50

mt x 0.60 mt at another side to form L shape as per

the design and drawing all edge shall be fixed with the

flat beading and shall be polished with color less polish

the work station shall be laminated with 1 mm thick of

approved make and under Neath shall be primered

painted with red oxide and fixed in to the cubical as

shown in the drawing Etc complete This rate includes


the place of work.

No

23

Rupees in words

12 CONTINUOUS TABLE:

Providing and fabricating by using 19 mm thick Block

Board /Ply of Regal / Uniply / Archid ply / Amul / Well

ply BWP /BWR wall to wall continues table, tabletop of

width 0.60-mt width. The table top shall be cut in

between the floor pedestal units to insert the cord,

the table top edge (front) shall be of 50 mm thick

shall be fixed over the pre fabricated floor pedestal

unit (shall be paid separately) at 1.22 mt distance the

table top shall be fixed with 1mm thick lamination of

approved make and color with required fevicol fixed

neatly. All cut edges of the block Board Ply shall be

fixed with flat beach wood beading finished neatly

with color less polish etc complete. This rate includes


the place of work.

Rmt

7.00

Rupees in words

13 TUFFENED GLASS PARTITION :

of 15

Providing and fixing 12 mm thick float toughened Glass

of approved make Saint Gobin/Asahi/Modi float,

neatly buffed edges polishing as per Design and fixing

the Glass with required ozone /patch fitting over the

ground and to the top portions finished neatly, Etc

complete This rate includes cost of all materials,


Sqmt

6.00

Rupees in words

14 TUFFENED GLASS DOOR :

Providing and fixing 12 mm thick float toughened Glass

Door of approved make Saint Gobin/Asahi/Modi float,

neatly buffed edges polishing as per Design and fixing

the Glass with required ozone / dorma medium

capacity auto door closure fixing in the floor with

cutting redoing the floor with required pivot fittings

and fixing Etc complete This rate includes cost of all


of work.

Sqmt

2.00

Rupees in words

15

DOOR FRAME :

Providing and fabricating and fixing the door frame of

beach wood of section 63 mm x 50 mm saw mill finish

with necessary grove to fix the door shutter fixing

the frame to the existing partition or wall opening

with required screw, hold fast melamine polishing

finishing neatly etc complete This rate includes cost


place of work.

Rmt

15.00

Rupees in words

16 FLUSH DOOR SHUTTER:

Providing and fabricating Flush Door shutter of

approved make of thick 32mm BWP/BWR Grade. All

cut edges of the block Board shall be fixed with Beach

wood Beading over the prefixed 4 mm thick ply (lipped

ply) to form groove all round the periphery, over the

shutter 1mm thick lamination of approved make and

color mat/ suede finished shall be fixed on both the

sides with required fevicol finished neatly all beading

surface shall be polished with color less polish finished

neatly. The shutter will also get fitted with 6 MM

Glass made slit at left /right hand side 150 mm x 1500

mm fixed with flat beading finished neatly and hard

ware materials like Godrej night latch/Auto

Lock/Barrel Lock, stainless steel handles of size 200

mm cm Etc complete This rate includes cost of all


of work.

Sqmt

2.00

Rupees in words

17 COMPUTER KEY BOARD UNIT:

Providing and fabricating and fixing the computer Key

of 15

Board of size 0.60 mt x 0.46 mt by using 19 thick ply

of approved make of BWP/BWR grade neatly cut and

fixed with all round flat beading and laminate of 1 mm

thick approved make and color and fixing the board

by telescopic sliding unit which should have ball roller

or readymade EBCO make computer Keyboard with

mouse pad . Etc complete This rate includes cost of

all materials, labor, and taxes, lead and lift, to the

place of work

No

35.00

Rupees in words

18 VERTICAL BLINDS:

Providing and fixing fabric VERTICAL blinds of

approved make and color with its all accessories in

good condition. Etc complete This rate includes cost of

all materials, labor, and taxes, lead and lift, to the

place of work.

Sqmt

150.00

Rupees in words

19

VOTCHER WRITING TABLE:

Providing and fabricating by using 19 mm block Board

/Ply of approved make Voucher writing table of size

1.22 mt x 0.30 mt x 0.80 Mt ht as per design and

Drawing Etc complete This rate includes cost of all


of work

No

2.00

Rupees in words

20 BLOCK BOARD FOOT REST:

Providing and fabricating block board foot rest by

using 19 mm Block Board /Ply Of approved make of

size 1mt x .60 mt tapered at foot end making the box

and keeping in position premiered the surface Etc


labor, and taxes, lead and lift, to the place of work

No

35.00

Rupees in words

21 PIN HEAD BOARD:

Providing and fixing the pin head Board by using Soft

Board, good Quality upholstery wrapped around and

sandwiched at back with 6 mm ply and fixed over the

surface Etc complete, this rate includes cost of all

materials, labor, taxes, lead and lift and other levies

to the place of work

Sqmt

10.00

Rupees in words

22 GYPSUM BOARD FALSE CEILING:

Providing and fixing Gypsum board false ceiling as,

with tier up and tier down box type design, the false

ceiling also should be cut opened where ever as

specified in circular /square shape, of required size to

fix the light fittings. The false ceiling shall be

fabricated and fixed by using companies specified

fixing materials like perimeter channels, G.I

of 15

intermediate channels, ceiling angles, Knurled web etc

shall be fixed to the ceiling with self expanding

screws hanged to the ceiling according to the spirit

level, plumb line below the fixed frame 12.5 mm thick

gypsum board false ceiling shall be fixed with flat star

head screws by mode of screw fasteners .The ceiling

bottom of the false ceiling shall be finished with two

coats of Emulsion paint of Berger make and color

finished with roller brush . Etc complete This rate

includes cost of all materials, labor, and taxes, lead

and lift, to the place of work.

Sqmt

100.00

Rupees in words

23 GRID SYSTEM OF FALSE CEILING :

Providing and fixing USG/ARM STRONG make Grid

Silhouette system of False ceiling by using company

specified wall angle, main runner ,1200 mm cross tee

,600 mm cross tee ,hanging wires 2 mm dia .90 mt

length successive hooks rawl plugs fixing at every

junction of the cross tee . All the fixtures fixed for

fluid level and checked for the level .After the frame

grid formation 12 mm thick approved tile of size 600

mm x 600 mm shall be laid inside the grids and

checked for level and adjusted Etc complete This rate

includes cost of all materials, labor, and taxes, lead

and lift, to the place of work

Sqmt

300.00

Rupees in words

24 WALL PANELLING DESIGN:

Providing fabricating wall paneling as per design and

drawing by using approved BWP/BWR grade

combination of 19 mm block board, 12 mm, and 6 mm

ply 1 mm thick lamination. The paneling shall be fixed

over the specified area in such a way that 19 mm block

board of 80 mm width frame work shall be fixed over

the wall according to the plumb line and length & at

600 mm c/c horizontally vertically, over which 12mm

ply 6 mm ply shall be fixed with necessary head less

nails with fevicol in such a way that even 12 mm ply

may get over lapped to form extra layer. Over the ply

1 mm thick lamination of approved make shall be fixed

the design may vary according to the site condition

and the designed on the spot contractor shall agree to

the sketches as made & fabricated neatly. Etc



Sqmt

60.00

Rupees in words

of 15

25 TEXTURED PAINT:

Providing wall textured paint by using the wall care

putty of approved make and creating textured surface

by using special tools and applying the surface with

the emulsion paint of approved color and make and

finishing neatly Etc complete This rate includes cost


place of work

Sqmt

60.00

Rupees

24 EMULSION PAINT:

Providing wall emulsion paint of approved make &

color with JK wall care putty and finishing neatly with

sponge roller ,brush Etc complete This rate includes


the place of work

Sqmt

.

200.00

Rupees in words

26 DECORATIVE WALL PAPER:

Providing and fixing the decorative wall paper of

approved make and color with recommended adhesive

cleaning the surface with required JK wall putty finish

etc complete This rate includes cost of all materials,

labor, and taxes, lead and lift, to the place of work

Sqmt

25.00

Rupees in words

27 Providing and fixing the 8 mm glass with required stud

bolts over the wall surface where ever as directed

with graphic Branding stickers as per the design and

graphic effects etc complete This rate includes cost


place of work

Sqmt

10.00

Rupees in words

Total

state bank of india administrative office zone … 2 of 15 tender form the, chief manager [gb] state...

Documents