stainless steel systems - grinnell.hu

24
STAINLESS STEEL SYSTEMS 139

Upload: others

Post on 14-May-2022

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: STAINLESS STEEL SYSTEMS - Grinnell.hu

STAINLESS

STEEL SYSTEMS

139

Page 2: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.140

Stainless Steel Systems Table of Contents

General notes: Additional information is included in our data sheets and is available upon request. It is the Designer’s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation constructions. Never remove any piping components nor correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified with the gasket recommendation listing for the specific application.

Figure 472

Stainless Steel Rigid Couplings

Page 142

Figure SS-7X

Stainless Steel Rigid Couplings (Large Diameter)

Page 143

Figure 405

Stainless Steel Flexible Couplings

Page 144

SS-8X

Stainless Steel Heavy Duty Flexible Coupling

Page 145

SS-1200

Stainless Steel High Pressure Flexible Couplings

Page 146

Figure 705R

Rilsan Coated Flexible Coupling

Page 147

SS-28

Stainless Steel Hinged Lever Coupling

Page 148

Figure SS-41

Flange Adapters (ANSI Class 150#)

Page 154

Figure 443 & 444

Flange Adapters (PN16/PN10 BS 4504)

Page 155

Figure 410

Stainless Steel 90° Elbows

Page 149

Figure 401

Stainless Steel 45° Elbows

Page 149

Figure 419

Stainless Steel Tees

Page 150

Figure 460

Stainless Steel End Caps

Page 151

Figure 421

Stainless Steel Reducing Tees

Page 152

Figure 450

Stainless Steel Concentric Reducers

Page 153

Figure SJ-400

Butterfly Valve

Pages 156 - 157

Figure SJ-600L

Ball Valve

Page 158

Figure SJ-600W

Ball Valve

Page 159

Figure SJ-630

Three Port Ball Valve

Page 160

Figure SJ-726

Y Strainer

Page 161

Figure SS-723

Mechanical Tee

Page 162

Page 3: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

141

MATERIAL SPECIFICATIONSStainless Steel Housing Specifications

specification for castings, iron-chromium,

for general application Grade CR-8M.

(70,000 psi)

(30,000 psi)

(2") minimum 30%

Bolt/Nut Specifications

conforming to ASTM A 193M Class 2, Type 316 Grade B8M

conforming to ASTM A 194M, Type 316, Grade 8M

Gasket Specifications

gaskets have a Green colour code stripe identification and conform to ASTM D 2000 for service temperatures from -34°C to 110°C (-30°F to 230°F). They are recommended for hot water not to exceed 110°C (230°F) plus a variety of dilute acids, oil free air, and many chemical services. They are not recommended for petroleum services.

gaskets have a Yellow and Green colour code stripe identification and are NSF-61 approved for cold and hot portable water up to 82°C (180°F).

gaskets have an Orange colour code stripe identification and conform to ASTM D 2000 for service temperatures from -29°C to 82°C (-20°F to 180°F). They are recommended for petroleum products, vegetable oils, mineral oils, and air with oil vapors.

gaskets are Red colour code stripe and conform to ASTM D 2000 for service temperatures from -34°C to 177°C ( -30°F to 350°F). They are recommended for air without hydrocarbons, or dry heat.

gaskets have a Blue colour code stripe and conform to ASTM D 2000. They are recommended for oxidizing acids, petroleum products, hydraulic fluids, lubricants, and halogenated hydrocarbons.

Fitting SpecificationsTech Data Sheet: G570

Coupling Specifications

MATERIAL SPECIFICATIONS

ASTM A 312, Schedule 10 and Schedule 40

ASTM A 403 WPW or A 403 CR

steel fittings are"

4.0mm (0.16") for 250 to 300mm (10" and 12"). Fittings are fabricated from SS316Ti / 1.4571

Fittings are available in full-flow and fabricated versions in 304 and 316L S.S. Fabricated fittings are available with Schedule 10 or Schedule 40 wall thickness.

For pressure ratings of fittings, refer to data sheet G570.

For local country potable water approvals, contact a GRINNELL Sales Representative.

For detailed Listing / Approval

information contact

GRINNELL Mechanical Products

* Shurjoint product specifications can be found at www.shurjoint.com

Page 4: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.142

Figure 472 Stainless Steel Rigid CouplingsTech Data Sheet: G560

The GRINNELL Figure 472 Rigid Coupling is made of cast 316L stainless steel and is capable of pressure up to 41.4 Bar (600 psi).

The GRINNELL Figure 472 Patented Coupling universal tongue-and-groove design allows the housing to grip along the full 360° of circumference of the pipe. Sizes 32mm – 100mm (1 1⁄4" – 4") have gripping teeth to prevent rotation during installation.

BC

A

Part Number

Pipe SizeMax.†

PressuresBarpsi

Max.†End Load

kNLbs.

Max.*‡ End Gap Inches mmInches

DimensionsCoupling Bolts

Size** mmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

472MD0042432 42.4 41.4 5.78 1.5 69.9 111.3 46.0 M10 x 57 0.9� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD0048440 48.3 41.4 7.57 2.0 76.2 117.3 46.0 M10 x 57 1.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD0060450 60.3 41.4 11.82 3.3 86.6 130.0 47.8 M10 x 57 0.9� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD0073465 73.0 41.4 17.32 3.3 99.3 143.0 47.8 M10 x 57 1.5� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD0076465 76.1 41.4 18.86 3.3 106.4 145.3 50.8 M10 x 57 1.6� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD0089480 88.9 41.4 25.68 3.3 117.6 158.8 47.8 M12 x 89 1.6 � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD01144100 114.3 41.4 42.44 4.8 147.6 190.5 50.0 M12 x 89 2.5� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD01394125 139.7 41.4 63.40 4.8 178.3 246.9 52.3 M16 x 83 3.9� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD01414125 141.3 41.4 64.87 4.8 180.1 246.6 51.8 M16 x 83 3.9 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD01684150 168.3 41.4 92.00 4.8 205.5 267.5 54.1 M16 x 83 4.3� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD02194200 219.1 41.4 155.92 4.8 268.2 344.4 66.5 M20 x 121 8.8 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD02734250 273.0 41.4 242.22 3.3 326.1 416.8 66.5 – 14.5� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

472MD03244300 323.9 41.4 340.73 3.3 391.4 478.5 66.5 – 19.5� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Figure 472 Rigid Couplings have an Anti-Rotation Feature of “gripping teeth” along the coupling keys in sizes 1 1 ⁄4" - 4" (32mm - 100mm ), making the Figure 472 perfectly suited for installations where the likelihood of rotation is greatest.

* Maximum available gap between pipe ends. Minimum gap = 0.

† Maximum Pressure and End Load are total from all loads based on standard weight stainless steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details.

‡ Max end gap is for cut grooved standard weight stainless steel pipe. Values for roll grooved pipe will be half that of cut grooved.** Contact a GRINNELL Sales Representative for availability of inch bolt sizes vs. metric bolt sizes.

For information on alternative sizes, contact a GRINNELL Sales Representative.

See page 141 for stainless steel coupling specifications and pages 234 - 245 for gasket information.

Refer to pressure ratings for Schedule 5, 10, and 40 pipe on pages 262 - 265, or contact a GRINNELL Sales Representative.

Note: The Fig. 472 Stainless Steel Heavy Duty Rigid Coupling does not provide compensation for pipe system expansion and/or contraction associated with pipe system temperature changes.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 5: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

143

Shurjoint Figure SS-7X Stainless Steel Rigid Couplings (Large Diameter)

Shurjoint Tech Data Sheet: K-02

The Shurjoint Model SS-7X is a tongue and groove rigid coupling designed to provide a rigid joint for stainless steel pipe in sizes 250 to 600mm (10” to 24”). The SS-7X is supplied standard in CF8 (304) and CF8M (316) with 304 and 316 bolts and nuts. The bolts must be fastened to the required torque for proper installation.

Pressure-Temperature Rating

NominalSizemmInches

PipeO. D.mmInches

Pipe EndSeparation

mmInches

Dimensions - mm Inches Bolt Approx.WeightkgLbs.

A B C No.Sizein

250 273.0 0-3.2 318 406 652 � � � � � � 10.5� � � � � � � � � � � � � � � � � � � � � � � � �

300 323.9 0-3.2 374 452 652 � � � � � � 11.5� � � � � � � � � � � � � � � � � � � � � � � � � �

350 355.6 0-3.2 397 500 752 � � � � � � 15.0� � � � � � � � � � � � � � � � � � � � � � � � � �

400 406.4 0-3.2 461 536 756 � � � � � 19.4� � � � � � � � � � � � � � � � � � � � � � � � � � � �

450 457.2 0-3.2 514 587 756 � � � � � 25.0� � � � � � � � � � � � � � � � � � � � � � � � �

500 508.0 0-3.2 571 669 798

� � � � � � 33.1� � � � � � � � � � � � � � � � � � � � � � � � � � � 550 558.8 0-3.2 622 720 79

8� � � � � � 33.0� � � � � � � � � � � � � � � � � � � � � � � � � � �

600 609.6 0-3.2 673 771 798

� � � � � � 34.7� � � � � � � � � � � � � � � � � � � � � � � � � � Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint

Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

See page 141 for stainless steel coupling specifications.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Nom. RatingWorking Pressure

(S40S, Roll-grooved)Max. ServiceTemperature

Class 15020 Bar @38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �

Nitrile: 82°C" � # $ � % & ! � � � �* The working pressure shown is based on roll-grooved Sch. 10S pipe. For

other pipe schedules and cut-grooved pipe, see page 76 Performance Data Sheet.

* Proof test pressure: 1.5 times the working pressure, non-shock cold water.

* Burst pressure is engineered minimum 2 times the working pressure.' () ' () ' ()250 – 350mm (10" – 14" ) 400 – 450mm (16" – 18" ) 500 – 600mm (20" – 24" )

Page 6: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.144

The GRINNELL Figure 405 Flexible Coupling is made of 316L stainless steel and is capable of pressures up to 51.7 Bar (750 psi), depending on pipe size and wall thickness.

B C

A

Figure 405 Stainless Steel Flexible CouplingsTech Data Sheet: G565

Part Number

Pipe SizeMax.†

PressuresBarpsi

Max.†

End LoadkNLbs.

Max.*‡ End GapmmInches

Deflection ‡ DimensionsCoupling

Bolts Size** (Qty. 2)mmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

Degreesper

coupling

mm/mIn/Ft

AmmInches

B mmInches

CmmInches

405MD0034425 33.7 51.7 4.53 3.3

5° 26'95.1 56.0 97.0 46.0 M10 x 57 0.6� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0042432 42.4 51.7 7.22 3.3

4° 19'75.0 65.0 106.4 46.0 M10 x 57 0.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0048440 48.3 51.7 9.46 3.3

3° 46'65.8 69.9 112.8 46.0 M10 x 57 0.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0060450 60.3 34.5 9.85 3.3

3° 1'52.5 82.6 124.0 47.8 M10 x 57 0.8� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0073465 73.0 34.5 14.44 3.3

2° 29'43.3 93.7 139.7 47.8 M10 x 57 0.9� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0076465 76.1 34.5 15.72 3.3

2° 23'41.7 101.6 146.10 47.8 M12 x 89 1.4� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD0089480 88.9 34.5 21.40 3.3

2° 3'35.8 111.3 165.1 47.8 M12 x 89 1.4 � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD01144100 114.3 22.4 22.99 6.4

3° 11'55.8 144.5 196.9 52.3 M12 x 89 1.8� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD01394125 139.7 13.8 21.13 6.4

2° 36'45.5 173.0 247.7 52.3 M16 x 83 3.3� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD01414125 141.3 13.8 21.62 6.4

2° 35'45.0 174.8 247.7 52.3 M16 x 83 3.2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD01684150 168.3 13.8 30.67 6.4

2° 10'37.5 201.7 271.5 52.3 M16 x 83 3.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

405MD02194200 219.1 13.8 51.97 6.4

1° 40'29.2 258.8 344.4 63.5 M20 x 121 6.6 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Values for roll grooved pipe will be half that of cut grooved.

* Maximum available gap between pipe ends. Minimum gap = 0.

† Maximum Pressure and end load are total from all loads based on standard weight stainless steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details.

‡ Max End Gap and Deflection is for cut grooved standard weight stainless steel pipe.

** Contact a GRINNELL Sales Representative for availability of inch bolt sizes vs. metric bolt sizes.

For information on alternative sizes, contact a GRINNELL Sales Representative.

See page 141 for stainless steel coupling specifications and pages 234 - 245 for gasket information.

For fire protection equipment listing and approval pressure ratings contact Tyco FPP.

Refer to pressure ratings for Schedule 5, 10, and 40 pipe on pages 262 - 265, or contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 7: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

145

The Shurjoint Model SS-8X is designed for high pressure applications including reverse osmosis and desalination systems. The SS-8X is available in Duplex CD3MN (2205), Super Duplex CE8MN, CE3MN (2507) and 6-Moly stainless steel CK3MCuN (254SMO*). The SS-8X features 316 bolts, washers and Silicon Bronze nuts to help prevent galling during repetitive use.

The SS-8X is also available in CF8M (316) with 316 bolts and nuts. contact GRINNELL for details.

* 254SMO is a registered trademark of AvestaPolarit AB.

NominalSizemmInches

PipeO. D.mmInches

Pipe EndSeparation

mmInches

DimensionsDeflectionDegree( ° )

BoltSizeInches

Approx.WeightkgLbs.

AmmInches

BmmInches

CmmInches

20 26.9 0 - 1.6 56.0 95.0 46.03° - 23’

� � � � 0.7� � � � � � � � � � � � � � � � � � � � � � � 25 33.7 0 - 1.6 63.0 99.0 46.0

2° - 45’� � � � 0.8� � � � � � � � � � � � � � � � � � � � �

32 42.4 0 - 1.6 72.0 111.0 46.02° - 10’

� � � � 0.9� � � � � � � � � � � � � � � � � � � � � � � � � �40 48.3 0 - 1.6 78.0 123.0 46.0

1° - 54’� � � � 1.0� � � � � � � � � � � � � � � � � � � � � � � � � �

50 60.3 0 - 1.6 88.0 134.0 47.01° - 31’

� � � � 1.2� � � � � � � � � � � � � � � � � � � �65 73.0 0 - 1.6 153.0 103.0 47.0

1° - 15’� � � � 1.3� � � � � � � � � � � � � � � � � � � � � � � � �

80 88.9 0 - 1.6 120.0 171.0 47.01° - 02’

� � � 1.8 � � � � � � � � � � � � � � � � � � � � � �100 114.3 0 - 3.2 152.0 201.0 52.0

1° - 36’� � � 2.4� � � � � � � � � � � � � � � � � � � �

125 141.3 0 - 3.2 181.0 249.0 53.01° - 18’

� � � � � 3.5 � � � � � � � � � � � � � � � � � � � �150 168.3 0 - 3.2 208.0 276.0 53.0

1° - 05’� � � � � 4.0� � � � � � � � � � � � � � � � � � � � �

200 219.1 0 - 3.2 267.0 341.0 62.00° - 50’

� � � � � � 6.8 � � � � � � � � � � � � � � � � � � � � �� � � * + , 216.3 0 - 3.2 264.0 338.0 62.00° - 51’

� � � � � � 6.5 � � � � � � � � � � � � � � � � � � � � � � Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section

VIII Division 1 pressure vessel test methods.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

See page 141 for stainless steel coupling specifications.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

SizeNom. Rating

Working Pressure(S40S, Cut-grooved)

Test Pressure(Hydrostatic)

Max. ServiceTemperature

20 - 100� � - � � - CWP97 Bar @38°C� � � � � � � � � � � � � 145 Bar� � � � � � � EPDM: 110°C� � � ! � � � �

125 - 200 - � - CWP70 Bar @38°C� � � � � � � � � � � � � 103 Bar� � � � � � Nitrile: 82°C" � # $ � % & ! � � � �

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only.

*Burst pressure is engineered minimum 2 times the working pressure.

Pressure-Temperature Rating

Shurjoint SS-8X Stainless Steel Heavy Duty Flexible Coupling

Shurjoint Tech Data Sheet: K-04

. /0

Page 8: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.146

Pressure-Temperature Rating

Fast-Fit Gasket:

Easy installation with a single hand

The Shurjoint Model SS-1200 is designed for high pressure applications including reverse osmosis, desalination and other specialty systems. The SS-1200 is available in strong and anti-corrosive alloys of Duplex CD3MN (2205), Super Duplex CE8MN, CE3MN (2507) and 6-Moly stainless steel CK3MCuN (254SMO*). The SS-1200 features 316 bolts, washers and Silicon Bronze nuts to help prevent galling during repetitive use.

The Fast-Fit gasket has been designed and engineered for easier and faster installations. The pipe-end friendly design eliminates struggling to stretch the gasket over the pipe ends and the Fast-Fit gasket also features Shurjoint’s Gap-Seal technology, which seals the gap between the pipe ends and eliminates stagnant water pockets within the gasket cavity. The Fast-Fit gasket is UL classified in accordance with ANSI/NSF 61 for potable water (Cold Water 30°C (86°F) / and Hot Water 82°C (180°F).

Always use the factory supplied Shurjoint Fast-Fit gasket. Performance standards do not support the use of a standard gasket in the SS-1200 coupling.* 254SMO is a registered trademark of AvestaPolarit AB.

Always use the Fast-fit gasket. Don't use a standard gasket with the SS-1200 coupling.

Pipe Size Pipe EndSeparation

mmInches

Dimensions - mm InchesDeflectionDegree( ° )

CouplingBolt Size(Qty 2) mmInches

ApproxWeightkgLbs.

Nominal mmInches

O.D.mmInches

A B C

20 26.9 0 - 1.6 53 94 463° - 23’

� � � � 0.45� � � � � � � � � � � � � � � � � � � � � � � � � �25 33.7 0 - 1.6 60 101 46

2° - 45’� � � � 0.55� � � � � � � � � � � � � � � � � � � � � �

32 42.4 0 - 1.6 70 111 462° - 10’

� � � � 0.63� � � � � � � � � � � � � � � � � � � � � � � � � � �40 48.3 0 - 1.6 76 117 46

1° - 54’� � � � 0.70� � � � � � � � � � � � � � � � � � � � � � � � � � � �

50 60.3 0 - 1.6 88 137 491° - 31’

� � � 1.04� � � � � � � � � � � � � � � � � � � � �65 73.0 0 - 1.6 102 151 49

1° - 15’� � � 1.38� � � � � � � � � � � � � � � � � � � � � � � �

80 88.9 0 - 1.6 119 168 491° - 02’

� � � 1.55 � � � � � � � � � � � � � � � � � � � � � �100 114.3 0 - 3.2 152 207 52

1° - 36’� � � � � 2.13� � � � � � � � � � � � � � � � � � � � �

Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

See page 141 for stainless steel coupling specifications.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Shurjoint SS-1200 Stainless Steel High Pressure Flexible CouplingsShurjoint Tech Data Sheet: K-17

Nom. Rating

Working Pressure (S40S, Roll-grooved)

Test Pressure(Hydrostatic)

Max. ServiceTemperature

CWP84 Bar @38°C� � � � � � � � � � � � � 126 Bar� � � � � � EPDM: 110°C� � � ! � � � �

Nitrile: 82°C" � # $ � % & ! � � � �*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only.

*Burst pressure is engineered minimum 2 times the working pressure.

1 2 3Housings:

A890 Grade 5A

Grade 4A

Page 9: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

147

Part Number

Pipe Size Max. WkPressure †

BarPsi

Max.End

Load †kNLbs

Max. EndSeparation ‡

mmInches

Deflection Dimensions CouplingBolt Size(Qty 2) mmInches

ApproxWeightkgLbs.

Nominal mmInches

O.D.mmInches

PerCouplingDegrees

Pipemm/min/ft

AmmInches

BmmInches

CmmInches

705MES042R32 42.4 16.0 2.21 3.3

4° 19'75.0 65 106 46

M10x600.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES048R40 48.3 16.0 2.90 3.3

3° 46'65.8 70 113 46

M10x600.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES060R50 60.3 16.0 4.53 3.3

3° 01'52.5 83 124 48

M10x600.8� � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES076R65 76.1 16.0 7.23 3.3

2° 23'41.7 102 146 48

M12x801.4� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES089R80 88.9 16.0 9.84 3.3

2° 03'35.8 111 165 48

M12x801.4 � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES114R100 114.3 16.0 16.27 6.4

3° 11'55.8 145 197 52

M12x801.8� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES139R125 139.7 16.0 24.31 6.4

2° 36'45.0 173 248 52

M16x903.3� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES141R125 141.3 16.0 24.87 6.4

2° 35'45.0 175 248 52

M16x903.2 � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES165R150 165.1 16.0 33.95 6.4

2° 12'38.3 197 272 52

M16x903.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES168R150 168.3 16.0 35.27 6.4

2° 10'37.5 202 272 52

M16x903.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

705MES219R200 219.1 16.0 59.78 6.4

1° 40'29.2 259 344 64

M20x1206.6 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

†: Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details. For fire protection equipment listing and approval pressure ratings contact a GRINNELL Sales Representative..

‡: Maximum pipe end separation is for cut grooved standard weight pipe. Values for roll grooved will be 1 ⁄ 2 that of cut grooved. Standard Stainless Steel 316 Bolt, Nuts and Washer.

Standard Stainless Steel 316 Bolt, Nuts and Washer.

Always use washers in combination with Fig 705R Rilsan Coated Couplings

Because of the Rilsan coating FM/UL/VDS/LPC approvals do not apply.

Also available with zinc plated bolts and nuts. Part code: 705ME...R (e.g. 705ME114R)

See page 141 for stainless steel coupling specifications.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Figure 705R Rilsan Coated Flexible Coupling

)' (

Page 10: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.148

The Shurjoint Model SS-28 Hinged Grooved Coupling is designed for quick connect and disconnect services. The housing segments are hinged with a lever handle for easy assembly. Use of the split pin can prevent the accidental opening of the coupling. The Model SS-28 can be used in a wide variety of applications with standard roll- or cut- grooved pipe. Housings 40mm - 100mm (1

1⁄2”- 4”) feature a smooth outer surface, housings 125mm - 300mm (5”- 12”) feature a cross-ribbed design for added strength. Standard gasket: Grade “E” EPDM or Grade “T” Nitrile. Available standard in CF8 (304) or CF8M (316).

Pressure-Temperature Rating

Expansion Pipe

Lever handles are factory assembled tight for safety. The use of an expansion pipe will aid the easy opening and closing. Expansion pipes are available upon request.

Pipe Size Max. WorkingPressure

BarPSI

AxialDisplacement

mmInches

Dimensions - mm InchesDeflectionDegree( ° )

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

A B C

40 48.3 20 0 – 1.6 75 118 47 4 � � 5 1.0� � � � � � � � � � � � � � � � � � � � � � � � � � �50 60.3 20 0 – 1.6 86 121 48 4 � � 5 1.1� � � � � � � � � � � � � � � � � � � � � � � �65 73.0 20 0 – 1.6 92 150 48 � 4 � � 5 1.4� � � � � � � � � � � � � � � � � � � � � � � � �65 76.1 20 0 – 1.6 92 150 48 � 4 � � � 5 1.4� � � � � � � � � � � � � � � � � � � � � � � � � � � � �80 88.9 20 0 – 1.6 119 163 48 � 4 � � � 5 1.8 � � � � � � � � � � � � � � � � � � � � � � � � �100 114.3 20 0 – 3.2 165 205 52 4 � � � 5 2.7� � � � � � � � � � � � � � � � � � � � � � �125 139.7 20 0 – 3.2 189 253 52 � 4 � � 5 4.9� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 125 141.3 20 0 – 3.2 189 253 52 � 4 � � 5 4.9 � � � � � � � � � � � � � � � � � � � � � � � 150 165.1 20 0 – 3.2 213 278 52 � 4 � � � 5 5.8� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 150 168.3 20 0 – 3.2 216 281 52 � 4 � � � 5 5.8� � � � � � � � � � � � � � � � � � � � � � � � �

*Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

See page 141 for stainless steel coupling specifications.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Shurjoint SS-28 Stainless Steel Hinged Lever CouplingShurjoint Tech Data Sheet: K-21

Nom. Rating

Working Pressure (STD, Roll-grooved)

Max. ServiceTemperature

Class 150

20 Bar @38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �Nitrile: 82°C" � # $ � % & ! � � � �

*Working pressure is based on cut-grooved Sch. 40S or 80S pipe only.

*Burst pressure is engineered minimum 2 times the working pressure.

' ( 6 7 8 9 :; 9 <6 7 8 9 :; 9 <=Locking Lever Handle:

A 743 Gr. CF8

Toggle Links, Hinge Pin, & Rivet:

Split Pin:

Page 11: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

149

Shurjoint Figure SS-41 Flange Adapters (ANSI Class 150#)

Shurjoint Tech Data Sheet: K-08The Shurjoint Model SS-41 stainless steel flange adapter allows for a direct connection with ANSI Class 125/150 flanges. The SS-41 is investment cast in Gr. CF8 (304) or CF8M (316). Integral closure tabs located on the flange OD help facilitate alignment and assembly.

Pressure-Temperature Rating

Pipe Size Max. WorkingPressure

Barpsi

Max. EndLoadkNLbs.

Dimensions Sealing Surface BoltsWeightkgLbs.

Nominal mmInches

O.D.mmInches

AmmInches

BmmInches

CmmInches

DmmInches

EmmInches

No.Size. in

50 60.3 20 5.71 152 121 21 60 874

5 ⁄ 8 x 3 2.1� � � � � � � � � � � � � � � � � � � � � � � � � �65 73.0 20 8.37 178 140 22 73 102

4 5 ⁄ 8 x 3 2.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

80 88.9 20 12.41 190 152 24 89 1164

5 ⁄ 8 x 3 3.1 � � � � � � � � � � � � � � � � � � � � � � � � � 100 114.3 20 20.51 229 191 24 114 141

8 5 ⁄ 8 x 3 4.5� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

150 168.3 20 44.47 279 241 25 168 1988

3 ⁄4 x 3 1 ⁄ 2 5.8� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �200 219.1 20 75.37 343 298 28 219 254

8 3 ⁄4 x 3 1 ⁄ 2 9.2 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

* Based on Sch. 10S pipe.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

See page 141 for stainless steel coupling specifications.

See pages 44-45 for flange washer Adaptor and page 267 flange drilling specifications

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Nom. RatingWorking Pressure

(S40S, Roll-grooved)Max. ServiceTemperature> % ? � � � � 20 Bar @38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �Nitrile: 82°C" � # $ � % & ! � � � �

pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe.

water.

) '@ A (MATERIAL SPECIFICATIONS Fitting Body:

A743 Gr. CF8

Page 12: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.150

Figure 443 & 444 Flange Adapters (PN16/PN10 BS 4504)Tech Data Sheet: G568

Pipe Size Figure 443 - PN16 Figure 444 - PN10 BS 4504

Nominal mmInches

O.D.mmInches

Part Number

E to E mmInches

Mating Flange BoltApprox. WeightkgLbs.

Part Number

E to E mmInches

Mating Flange BoltApprox. WeightkgLbs.

Qty. Size * Qty. Size *

32 42.4443H000424

904

M16 x 65 1.8–

––

– –� � � � � � � � � � � � �40 48.3

443H00048492

4M16 x 65 2.0

––

–– –� � � � � � � � � � � � � �

50 60.3443H000604

954

M16 x 65 2.7–

––

– –� � � � � � � � � �65 76.1

443H00076495

4M16 x 65 3.3

––

–– –� � � � � � � � � � � � � � �

80 88.9443H000894

1008

M16 x 70 4.0–

––

– – � � � � � � � 100 114.3

443H001144102

8M16 x 70 4.6

––

–– –� � � � � � � � � � � � �

125 139.7443H001394

1058

M16 x 75 6.0–

––

– –� � � � � � � � � � � � � � �150 168.3

443H001684105

8M20 x 80 7.2

––

–– –� � � � � � � � � � �

200 219.1–

––

– –444H002194

112.08

M20 x 80 10.2 � � � � � � � � � � 250 273.0

––

–– –

444H002734138.0

12M20 x 90 18.0� � � � � � � � � �

300 323.9–

––

– –444H003244

138.012

M20 x 90 22.4� � � � � � � � � � � � �* = Bolts are not supplied. Bolt lengths shown are standard; it is the responsibility of the purchaser to verify correct lengths

for intended applications

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See pages 44-45 for flange washer Adaptor and page 267 flange drilling specifications

See page 141 for stainless steel specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

A : B A

Page 13: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

151

( : B A C D E F

Figure 410 90° Stainless Steel Elbows

Tech Data Sheet: G570

Figure 401 45° Stainless Steel Elbows

Tech Data Sheet: G570

Part Number

Pipe SizeC to EmmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

410H00034425 33.7 73.0 0.5� � � � � � � � � �

410H00042432 42.4 83.0 0.5� � � � � � � � � � � � � �

410H00048440 48.3 92.0 0.5� � � � � � � � � � � � � �

410H00060450 60.3 111.0 0.9� � � � � � � � � �

410H00076465 76.1 130.0 1.4� � � � � � � � � � � � � � �

410H00089480 88.9 149.0 2.0 � � � � � � � �

410H001144100 114.3 187.0 3.9� � � � � � � � � �

410H001394125 139.7 225.0 6.1� � � � � � � � � � � � � �

410H001684150 168.3 263.0 8.4� � � � � � � � � �

410H002194200 219.1 345.0 16.6 � � � � � � � �

410H002734250 273.0 421.0 27.2� � � � � � � � � � � � � � �

410H003244300 323.9 437.0 30.4� � � � � � � � � � � � � � � �

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Part Number

Pipe SizeC to EmmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

401H00034425 33.7 50.0 0.5� � � � � � � � � � �

401H00042432 42.4 54.0 0.5� � � � � � � � � � � � � �

401H00048440 48.3 58.0 0.5� � � � � � � � � � � � � �

401H00060450 60.3 65.0 0.9� � � � � � � � � �

401H00076465 76.1 73.0 1.4� � � � � � � � � � � � � � �

401H00089480 88.9 80.0 2.0 � � � � � � � �

401H001144100 114.3 95.0 3.9� � � � � � � � � �

401H001394125 139.7 110.0 6.1� � � � � � � � � � � � � �

401H001684150 168.3 125.0 8.4� � � � � � � � � � �

401H002194200 219.1 160.0 16.6 � � � � � � � � �

401H002734250 273.0 190.0 27.2� � � � � � � � � � � � � �

401H003244300 323.9 220.0 30.4� � � � � � � � � � � � � �

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 14: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.152

G H I J G H I J

Figure 419 TeesTech Data Sheet: G570

Part Number

Pipe SizeC to EmmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

419H00034425 33.7 73.0 0.5� � � � � � � � � �

419H00042432 42.4 60.0 0.5� � � � � � � � � � � � � �

419H00048440 48.3 62.0 0.5� � � � � � � � � � � � � � �

419H00060450 60.3 68.0 0.9� � � � � � � � � �

419H00076465 76.1 76.0 1.4� � � � � � � � � � � � � � � �

419H00089480 88.9 86.0 2.0 � � � � � � � �

419H001144100 114.3 105.0 3.9� � � � � � � � � �

419H001394125 139.7 160.0 6.1� � � � � � � � � � � � � � �

419H001684150 168.3 178.0 8.4� � � � � � � � � � �

419H002194200 219.1 218.0 16.6 � � � � � � �

419H002734250 273.0 256.0 27.2� � � � � � � � � � � � � � �

419H003244300 323.9 294.0 30.4� � � � � � � � � � � � � � �

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 15: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

153

K L M K

Figure 460 End CapsTech Data Sheet: G570

Part Number

Pipe Size NominalE to EmmInches

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

460H00034425 33.7 58.0 0.5� � � � � � � � � �

460H00042432 42.4 58.0 0.5� � � � � � � � � � � � � �

460H00048440 48.3 58.0 0.5� � � � � � � � � � � � � �

460H00060450 60.3 58.0 0.9� � � � � � � � � �

460H00076465 76.1 60.0 1.4� � � � � � � � � � � � � � �

460H00089480 88.9 60.0 2.0 � � � � � � � � �

460H001144100 114.3 60.0 3.9� � � � � � � � � �

460H001394125 139.7 60.0 6.1� � � � � � � � � � � � � � �

460H001684150 * 168.3 66.0 8.4� � � � � � � � � � �

460H002194200 * 219.1 81.0 16.6 � � � � � � � � �

460H002734250 * 273.0 81.0 27.2� � � � � � � � � � � � � �

460H003244300 * 323.9 81.0 30.4� � � � � � � � � � � � � �

* Dished Cap

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 16: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.154

Figure 421 Reducing TeesTech Data Sheet: G570

Part Number

Pipe SizeC to EmmInches

C to BmmInches

Approx. WeightkgLbs.

Nominal mmInches

O.D.mmInches

421H02010450 x 50 x 25 60.3 x 60.3 x 33.7 68.0 68.0 1.0� � � � � � � � � � � � � � � � � � � � � � � � �

421H02012450 x 50 x 32 60.3 x 60.3 x 42.4 68.0 68.0 1.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H02015450 x 50 x 40 60.3 x 60.3 x 48.3 68.0 68.0 1.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H02615450 x 50 x 40 76.1 x 76.1 x 48.3 76.0 76.0 1.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H02620450 x 50 x 50 76.1 x 76.1 x 60.3 76.0 76.0 2.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H03020480 x 80 x 50 88.9 x 88.9 x 60.3 83.0 86.0 2.5 � � � � � � � � � � � � � � � � � � � �

421H03026480 x 80 x 65 88.9 x 88.9 x 76.1 83.0 86.0 2.6 � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H042204100 x 100 x 50 114.3 x 114.3 x 60.3 95.0 105.0 4.6� � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H042264100 x 100 x 65 114.3 x 114.3 x 76.1 95.0 105.0 5.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H042304100 x 100 x 80 114.3 x 114.3 x 88.9 95.0 105.0 5.2� � � � � � � � � � � � � � � � � � � � � � � � � �

421H052304125 x 125 x 80 139.7 x 139.7 x 88.9 108.0 124.0 6.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H052424125 x 125 x 100 139.7 x 139.7 x 114.3 108.0 124.0 6.7� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H063204150 x 150 x 50 168.3 x 168.3 x 88.9 122.0 143.0 11.8� � � � � � � � � � � � � � � � � � � � � � � � � � �

421H063264150 x 150 x 65 168.3 x 168.3 x 76.1 122.0 143.0 12.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H063304150 x 150 x 80 168.3 x 168.3 x 60.3 122.0 143.0 12.1� � � � � � � � � � � � � � � � � � � � � � � � � �

421H063424150 x 150 x 100 168.3 x 168.3 x 114.3 122.0 143.0 12.2� � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H063524150 x 150 x 125 168.3 x 168.3 x 139.7 122.0 143.0 12.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H080424200 x 200 x 100 219.1 x 219.1 x 114.1 148.0 178.0 24.2 � � � � � � � � � � � � � � � � � � � � � �

421H080524200 x 200 x 125 219.1 x 219.1 x 139.7 148.0 178.0 24.2 � � � � � � � � � � � � � � � � � � � � � � � � �

421H080634200 x 200 x 150 219.1 x 219.1 x 168.3 148.0 178.0 24.2 � � � � � � � � � � � � � � � � � � � � � �

421H011634250 x 250 x 150 273.0 x 273.0 x 168.3 194.0 216.0 30.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H011804250 x 250 x 200 273.0 x 273.0 x 219.1 204.0 216.0 30.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H013804300 x 300 x 200 323.9 x 323.9 x 219.1 229.0 254.0 35.6� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

421H013114300 x 300 x 250 323.9 x 323.9 x 273.0 242.0 254.0 35.6� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

N O P QN O P R

Page 17: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

155

A : B AFigure 450 Concentric Reducers

Tech Data Sheet: G570

Part Number

Pipe SizeE to EmmInches

Approx. Weight kgLbs.

Nominal mmInches

O.D.mmInches

450H01210432 x 25 42.4 x 33.7 120.0 0.5� � � � � � � � � � � � � � � � � � � � �

450H01510440 x 25 48.3 x 33.7 134.0 0.5� � � � � � � � � � � � � � � � � � �

450H01512440 x 32 48.3 x 42.4 99.0 0.5� � � � � � � � � � � � � � � � � � � � � � � �

450H02015450 x 40 60.3 x 48.3 111.0 1.0� � � � � � � � � � � � � � � � � � � �

450H02615465 x 40 76.1 x 48.3 125.0 1.0� � � � � � � � � � � � � � � � � � � � � � � � � � �

450H02620465 x 50 76.1 x 60.3 125.0 1.1� � � � � � � � � � � � � � � � � � � � � � �

450H03015480 x 40 88.9 x 48.3 125.0 1.1 � � � � � � � � � � � � � � � � � � � �

450H03020480 x 50 88.9 x 60.3 125.0 1.1 � � � � � � � � � � � � � � � �

450H03026480 x 65 88.9 x 76.1 125.0 1.1 � � � � � � � � � � � � � � � � � � � � � �

450H042204100 x 50 114.3 x 60.3 135.0 1.1� � � � � � � � � � � � � � � �

450H042264100 x 65 114.3 x 76.1 135.0 1.3� � � � � � � � � � � � � � � � � � � � � �

450H042304100 x 80 114.3 x 88.9 135.0 1.3� � � � � � � � � � � � � � �

450H052304125 x 80 139.7 x 88.9 162.0 1.3� � � � � � � � � � � � � � � � � � �

450H052424125 x 100 139.7 x 114.3 162.0 1.6� � � � � � � � � � � � � � � � � � �

Part Number

Pipe SizeE to EmmInches

Approx. Weight kgLbs.

Nominal mmInches

O.D.mmInches

450H063424150 x 100 168.3 x 114.3 175.0 1.6� � � � � � � � � � � � � � � �

450H063524150 x 125 168.3 x 139.7 210.0 1.7� � � � � � � � � � � � � � � � � � � � �

450H080424200 x 100 219.1 x 114.3 227.0 1.7 � � � � � � � � � � � � � � �

450H080524200 x 125 219.1 x 139.7 227.0 2.5 � � � � � � � � � � � � � � � � � �

450H080634200 x 150 219.1 x 168.3 227.0 2.5 � � � � � � � � � � � � � �

450H011634250 x 150 273.0 x 168.3 278.0 2.5� � � � � � � � � � � � � � � � � � � �

450H011804250 x 200 273.0 x 219.1 278.0 3.4� � � � � � � � � � � � � � � � � � �

450H013804300 x 200 323.9 x 219.1 300.0 4.7� � � � � � � � � � � � � � � � � � � �

450H013114300 x 250 323.9 x 273.0 300.0 5.2� � � � � � � � � � � � � � � � � � � � � � �

For information on alternative sizes, contact a GRINNELL Sales Representative.

Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative.

See page 141 for stainless steel fitting specifications.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Page 18: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.156

The Shurjoint Model SJ-400 Butterfly Valve is a grooved end stainless steel butterfly valve, supplied with a 10 position lever handle (SJ-400-L) or worm gear operator (SJ-400-W). The body is available in CF8M (type 316) to ASTM A 743 with integral neck and ISO 5211 mounting pad. It features a dual seal disc encapsulated with Gr. E EPDM for cold and hot water services. The end-to-end dimensions conform to MSS SP-67. The SJ-400 is UL classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23°C (73.4°F).

Pressure-Temperature Rating

Shurjoint Figure SJ-400 Butterfly Valve(Page 1 of 2)

Shurjoint Tech Data Sheet: K-16

Nom. Rating

Working Pressure (S40S, Roll-grooved)

Max. ServiceTemperature

Class 150

20 Bar @38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �Nitrile: 82°C" � # $ � % & ! � � � �

pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe.

SJ-400-L50 - 300mm (2" - 12")

SJ-400-W350 - 600mm (14" - 24")

MATERIAL SPECIFICATIONSValve Body:

743, A 351, or A 744 which is UL classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23°C (73.4°F).

Stems:

Disc:

EPDM.

Disc Encapsulation:

: EPDM Rubber is classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23°C (73.4°F)

O-Rings:

Gear Box:

A 351.

Pipe Size Equivalent Length on Sch. 40 Pipe*

MeterFeet

Cv ValuesNominal mmInches

O.D.mmInches

50 60.3 2.48120� � � � � �

65 73 2.48210� � � � � � �

65 76.1 2.48210� � � � � � � � � � � �

80 88.9 2.56380 � � � � �

100 114.3 2.53720� � � � � �

125 139.7 2.991150� � � � � � � � � � �

125 141.3 2.991150 � � � �

150 165.1 2.262250� � � � � � � � � � � � �

150 168.3 2.262250� � � � � � � �

200 219.1 3.353800 � � � � � � �

250 273.0 3.205500� � � � � � � � � �

300 323.9 3.668250� � � � � � � � � � �

350 355.6 7.629500� � � � � � � � � � �

400 406.4 7.9213000� � � � � � � � � � � �

450 457.2 9.7516000� � � � � � � � �

500 508.0 11.3720000� � � � � � � � � �

600 609.6 13.3229000� � � � � � � � � � �

* At 15 feet/sec. (4.6m/s) velocity of water.

Page 19: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

157

SJ-400-L50 - 300mm (2" - 12")

SJ-400-W350 - 600mm (14" - 24")

Shurjoint Figure SJ-400 Butterfly Valve(Page 2 of 2)

Shurjoint Tech Data Sheet: K-16

Pipe Size Dimensions - mm Inches Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

A B C DE

(Gear Operator)

E (Lever)

FmmInches

50 60.3 81 64 63 106 153 192 154 2.3� � � � � � � � � � � � � � � � � � � � � � � � � � � � �65 73 97 79 68 110 153 192 154 3.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � �65 76.1 97 79 68 110 153 192 154 3.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �80 88.9 97 92 76 126 153 192 154 3.5 � � � � � � � � � � � � � � � � � � � � � � � � �100 114.3 116 118 89 135 153 260 154 5.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � �125 139.7 148 145 102 168 153 260 154 7.1� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �125 141.3 148 145 102 168 153 260 154 7.1 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �150 165.1 148 145 102 184 153 260 154 9.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 150 168.3 148 145 102 184 153 260 154 9.2� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 200 219.1 133 222 140 208 200 260 203 12.2 � � � � � � � � � � � � � � � � � � � � � � � � � � �250 273.0 159 276 170 235 200 356 203 28.3� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �300 323.9 165 327 205 260 200 356 203 40.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �350 355.6 178 365 224 276 242 – 305 59.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �400 406.4 178 416 248 302 242 – 305 67.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �450 457.2 203 470 283 350 242 – 305 86.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �500 508.0 216 527 314 383 290 – 412 133.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �600 609.6 254 629 368 453 290 – 412 160.0� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

)A

S T @ T@' ' ( @AUS T @ T )

Page 20: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.158

Shurjoint Figure SJ-600L Ball Valve(Lever)

(Page 1 of 2)

Shurjoint Tech Data Sheet: K-12The Shurjoint Model SJ-600L is a stainless steel, grooved-end, two-piece, full port ball valve designed and tested in conformance with MSS SP-110 and SP-72. The lever handle is equipped with tamper resistant locking holes. The SJ-600L is comprised of a stainless steel body and end cap, virgin TFE seats and stainless steel trim. The valve is supplied standard in CF8M (316).

Pressure-Temperature Rating

40 - 80mm (1 1⁄2" - 3")

100mm (4")

Pipe Size Dimensions - mm Inches

Cv Value

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

L H W d

40 48.3 140 94 193 38270

3.0� � � � � � � � � � � � � � � � � � � � � � �50 60.3 156 105 193 50

5004.0� � � � � � � � � � � � � � � � � � �

65 73.0 180 110 250 65800

7.0� � � � � � � � � � � � � � � � � � � � �65 76.1 180 110 250 65

8007.0� � � � � � � � � � � � � � � � � � � � � � � � �

80 88.9 214 152 250 781200

9.4 � � � � � � � � � � � � � � � � � � � �100 114.3 240 167 290 100

215025.0� � � � � � � � � � � � � � � � � � � � �

* The weight includes the lever handle.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Nom. Rating

Working Pressure (S40S, Roll-grooved)

Shell Test(Hydrostatic)

Max. ServiceTemperature

CWP42 Bar @38°C� � � � � � � � � � � � 63 Bar� � � � � � EPDM: 110°C� � � ! � � � �

Nitrile: 82°C" � # $ � % & ! � � � �*Working pressure is for connection with cut- or roll-grooved

schedule Sch. 40S pipe.

*Seat test: 110% the working pressure.

VW XY

MATERIAL SPECIFICATIONSBody, End Cap, Stem, and Ball:

Seats:

Seals:

Lever Handle:

Flow Data (Cv Values in Dimensions table):

Values for flow of water at 16°C (60°F).Where: Cv = Flow coefficient Q = Flow (GPM) ∆P = Pressure drop (psi)

Page 21: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

159

Shurjoint Figure SJ-600W Ball Valve(Gear)

(Page 2 of 2)

Shurjoint Tech Data Sheet: K-12The Shurjoint Model SJ-600W is supplied with a worm gear operator. The standard gear operator is supplied with a bracket and extension sleeve. The ISO 5211 mounting pad allows for mounting of other power actuators. Sizes available are 50 to 100mm (2" to 4").

Pipe Size Dimensions - mm Inches

Cv Value

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

K H W

50 60.3 152 137 203500

8.10� � � � � � � � � �65 73.0 152 145 203

80011.10� � � � � � � � � � � � � �

65 76.1 152 145 203800

11.10� � � � � � � � � � � � � � � � � �80 88.9 152 182 203

120013.50 � � � � � � � � � � � � �

100 114.3 152 203 2032150

29.0� � � � � � � � � � � �* The weight includes the worm gear operator.

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

XZ V

General Notes:

Maximum Working Pressure (CWP) listed is the maximum cold water pressure for general piping services tested to ASTM F1476 and or AWWA C606 methods. Figures listed are based on roll- or cut-grooved standard wall stainless steel pipe. For other pipe schedules or pipe materials, contact Shurjoint for additional information.

Field Joint Test: For one time only the system may be tested hydrostatically at 1½ times the maximum working pressure listed (AWWA C606 5.2.3).

Warning: Piping systems must always be depressurized and drained before attempting disassembly and or removal of any components.

Shurjoint reserves the right to change specifications, designs and or standard without notice and without incurring any obligations.

Page 22: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.160

Shurjoint Figure SJ-630 Three Port Ball ValveShurjoint Tech Data Sheet: K-25

The Shurjoint Model SJ-630 is a grooved-end three-port ball valve designed to divert media from bottom inlet to either of the two outlets ports. The valve port is a regular port size and the stem is a blowout proof design to MSS SP-72 and API Standard 608. The valve is supplied with a carbon steel lever handle equipped with a tamper resistant locking device.

The valve body and three-port ball are made of austenitic stainless steel conforming to ASTM A351 CF8M(316) and blowout proof stem is stainless steel to ASTM A479 Type 316. The Valve body and trim materials are in compliance with NACE MR-01-75 requirement.

Pressure-Temperature Rating

Pipe Size Dimensions - mm Inches

Cv / Kv Value

Approx. WeightkgLbs.

Nominal mmInches

O.D.mmInches

L H W d A B

50 60.3 167 110 228 38 83 7936 / 31

3.58� � � � � � � � � � � � � � � � � � � � � �Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint

Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

Nom. Rating

Working Pressure (S40S, Roll-grooved)

Max. ServiceTemperature

CWP41 Bar @38°C� � � � � � � � � � � � EPDM: 110°C� � � ! � � � �

Nitrile: 82°C" � # $ � % & ! � � � �* Working pressure is based on connection with roll- or cut-

grooved Sch. 40S stainless steel pipe.

* Seat test: 110% the working pressure.

* Shell test: 1.5 times the working pressure.

V X)WS T @ T Y 'MATERIAL SPECIFICATIONSBody, End Cap & Ball:

Stem:

Seats:

Body Seal:

Stem Hardware:

Lever Handle:

Page 23: STAINLESS STEEL SYSTEMS - Grinnell.hu

Refer to back cover for country-specific contact information

STAINLESS STEEL SYSTEMS

Stainless

Steel

161

Shurjoint Figure SJ-726 Y StrainerShurjoint Tech Data Sheet: K-11

Pressure-Temperature Rating

The Shurjoint Model SS-726 Stainless Steel Grooved-end Y-Strainers are designed to strain debris and foreign matter from piping systems and thus provide inexpensive protection for costly pumps, meters and other components. Cleaning and maintenance of the screen can be accomplished easily by removing the coupling. The Model SS-726 Stainless Steel Y-Strainer is suitable for vertical or horizontal installations.

Nom. Rating

Working Pressure(S40S, Roll-grooved)

Max. ServiceTemperature

Class 150

20 Bar @ 38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �Nitrile: 82°C" � # $ � % & ! � � � �

pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe.

water.

Pipe Size Max. Working Pressure

Bar� � � Dimensions - mm Inches Drain PlugSizemmInches

Cv Valve

Approx.WeightkgLbs.

Nominal mmInches

O.D.mmInches

A B C

65 73.0 20 273 199 122 1592

7.6� � � � � � � � � � � � � � � � � � � � � � �80 88.9 20 299 221 129 15

1628.6 � � � � � � � � � � � � � � � � � � �

100 114.3 20 362 269 168 25284

9.6� � � � � � � � � � � � � � � � � � � � � � � �150 168.3 20 470 357 219 25

77039.0� � � � � � � � � � � � � � � � � � �

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

'( )

MATERIAL SPECIFICATIONSBody, End-Cap, Drain Plug and Coupling Segments:

A 743 Gr. CF8

Bolts & Nuts:

B-8 with heavy duty nuts to ASTM A 194 B8, Molybdenum disulfide (MoS2) coated.

B-8M with heavy duty nuts to ASTM B8M, Molybdenum disulfide (MoS2) coated.

Screen:

Factory’s standard screen perforation is 3.2mm ( 1⁄8"). Other perforations are available upon request.

Flow Data (Cv Values in Dimensions table):

Values for flow of water at 16°C (60°F).Where: Cv = Flow coefficient Q = Flow (GPM) ∆P = Pressure drop (psi)

Page 24: STAINLESS STEEL SYSTEMS - Grinnell.hu

www.grinnell.com

STAINLESS STEEL SYSTEMS

Stainless

Steel

GRINNELL reserves the right to change the contents without notice.162

Shurjoint Figure SS-723 Mechanical TeeShurjoint Tech Data Sheet: K-10

Pressure-Temperature Rating

Nom. Rating

Working Pressure(S40S, Roll-grooved)

Max. ServiceTemperature

Class 150

20 Bar @ 38°C � � � � � � � � � � � EPDM: 110°C� � � ! � � � �Nitrile: 82°C" � # $ � % & ! � � � �

The Shurjoint Model SS-723 stainless steel mechanical tee is the ideal fitting for branch or direct outlet connections to sprinkler heads, drop nipples and or gauges on stainless steel pipe. No need for welding, simply cut or drill a hole at the desired location, position the housing so that the locating collar fits within the hole and secure with the bolts and nuts. The SS-723 is comprised of stainless steel investment cast housings, EPDM gasket and stainless steel track bolts and nuts. The SS-723 is available in grades CF8 (304) and CF8M (316). Additional sizes and or grades are available on request, please contact for Shurjoint for details.

Pipe Size HoleDiameter

mmInches

Dimensions - mm Inches Sealing Surface - mm Inches

Bolt Size. in

Approx.WeightkgLbs.

Nominal mmInches

A B C D T*

32 x 15 30 41 26 87 49 27 5 ⁄ 16 x 1 1 ⁄ 2

0.3� [ � \ � � � � � � � � � � � � � � � � � � � � � � � �32 x 20 30 44 26 87 49 29

5 ⁄ 16 x 1 1 ⁄ 20.3� [ � ] � � � � � � � � � � � � � � � � � � � � � � � �

32 x 25 30 51 26 87 49 34 5 ⁄ 16 x 1 1 ⁄ 2

0.4� [ � � � � � � � � � � � � � � � � � � � � � � � � �40 x 15 30 44 29 90 49 30

5 ⁄ 16 x 1 1 ⁄ 20.3� \ � \ � � � � � � � � � � � � � � � � � � � � �

40 x 20 30 46 29 90 49 31 5 ⁄ 16 x 1 1 ⁄ 2

0.3� \ � ] � � � � � � � � � � � � � � � � � � � � �40 x 25 30 53 29 90 49 36

5 ⁄ 16 x 1 1 ⁄ 20.4� \ � � � � � � � � � � � � � � � � � � � � � � � �

50 x 15 30 51 36 109 51 37 5 ⁄ 16 x 1 1 ⁄ 2

0.5� � \ � � � � � � � � � � � � � � � � � � � � � � � � �50 x 20 30 53 36 109 51 28

5 ⁄ 16 x 1 1 ⁄ 20.5� � ] � � � � � � � � � � � � � � � � � � � � � � � � �

T*: Take-out (Centre of run to end of pipe to be engaged)

Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com.

For information on alternative sizes, contact a GRINNELL Sales Representative.

For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative.

' () @^ _ ` a b c dFor detailed Listing / Approval

information contact

GRINNELL Mechanical Products

MATERIAL SPECIFICATIONSHousing:

Bolts & Nuts:

nuts to ASTM A 194 B8, Molybdenum disulfide (MoS2) coated.

duty nuts to ASTM B8M, Molybdenum disulfide (MoS2) coated.