skills for employment investment program (seip) · 2019. 7. 25. · cblm – plumbing (student...
TRANSCRIPT
Skills for Employment
Investment Program (SEIP)
COMPETENCY-BASED LEARNING
MATERIAL
(STUDENT GUIDE)
FOR
PLUMBING
(CONSTRUCTION SECTOR)
Finance Division, Ministry of Finance
Government of the People’s Republic of Bangladesh
CBLM – Plumbing (Student Guide) v.1 Oct 2018 2
Skills for Employment Investment Programme (SEIP)
Table of Contents
Copyright 4
How to Use this Competency-based Learning Material 5
List of Icons 6
Modules 7
Module 1: Perform pipe threading operation 7
Learning Outcome 1.1 - Gather and check tools, equipment and materials 8
Learning Outcome 1.2 - Carry out steel pipe cutting operation 16
Learning Outcome 1.3 - Carry out thread cutting operation 22
Learning Outcome 1.4 - Assemble pipe run 26
Learning Outcome 1.5 - Clean/maintain the work area 29
Answer Key 33
Module 2: Perform access cutting and encroachment works 35
Learning Outcome 2.1 - Interpret drawings and plumbing plans 36
Learning Outcome 2.2 - Inspect encroachment work area 39
Learning Outcome 2.3 - Gather tools, equipment and materials 41
Learning Outcome 2.4 - Cut and make access through walls and floors 45
Learning Outcome 2.5 - Clean/maintain the work area 47
Answer Key 48
Module 3: Carry out water supply line installation using G.I, PPR/HDP pipes 49
Learning Outcome 3.1 - Gather and inspect tools, equipment and materials 50
Learning Outcome 3.2 - Perform pipe cutting operation 56
Learning Outcome 3.3 - Perform pipe threading operation 62
Learning Outcome 3.4 - Assemble pipe runs 65
Learning Outcome 3.5 - Clean/maintain the work area 68
Answer Key 69
Module 4: Carry out water supply line installation using PVC/UPVC pipes 70
Learning Outcome 4.1 - Gather and inspect tools, equipment and materials 71
Learning Outcome 4.2 - Perform PVC/UPVC pipe run operation 75
Learning Outcome 4.3 - Perform PVC/UPVC pipe run assembly 81
Learning Outcome 4.4 - Clean/maintain the work area 85
Answer Key 86
Module 5: Carry out sewer pipe line installation 87
Learning Outcome 5.1 - Plan out foe sewer pipe line installation 88
Learning Outcome 5.2 - Gather tools, equipment and materials 90
Learning Outcome 5.3 - Carry out trenching and bedding works 95
Learning Outcome 5.4 - Lay sewer pipe and finish final pipe run 98
Learning Outcome 5.5 - Finish final pipe run 101
CBLM – Plumbing (Student Guide) v.1 Oct 2018 3
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.6 - Clean/maintain the work area 104
Answer Key 105
Module 6: Carry out plumbing fixtures installation 106
Learning Outcome 6.1 - Prepare for plumbing fixture installation 107
Learning Outcome 6.2 - Gather tools, equipment and materials 111
Learning Outcome 6.3 - Install a new toilet bowl (commode) 112
Learning Outcome 6.4 - Install other plumbing fixtures 118
Learning Outcome 6.5 - Clean/maintain the work area 127
Answer Key 128
Module 7: Perform pressure testing of piping system 129
Learning Outcome 7.1 - Prepare for pressure testing 130
Learning Outcome 7.2 - Gather tools, equipment and materials 133
Learning Outcome 7.3 - Carry out pressure testing 136
Learning Outcome 7.4 - Clean/maintain the work area 139
Answer Key 140
CBLM – Plumbing (Student Guide) v.1 Oct 2018 4
Skills for Employment Investment Programme (SEIP)
Copyright
The Competency-based Learning Material (Student Guide) for Plumbing is a document, aligned to its
applicable competency standard, for providing training consistent with the requirements of industry in order
for individuals who graduated through the established standard via competency-based assessment to be
suitably qualified for a relevant job.
This document is owned by the Finance Division of the Ministry of Finance of the People’s Republic of
Bangladesh, developed under the Skills for Employment Investment Program (SEIP).
Public and private institutions may use the information contained in this competency-based learning
material for activities benefitting Bangladesh.
Other interested parties must obtain permission from the owner of this document for reproduction of
information in any manner, in whole or in part, of this Competency-based Learning Material, in English or
other language.
This document is available from:
Skills for Employment Investment Program (SEIP) Project
Finance Division
Ministry of Finance
Probashi Kallyan Bhaban (Level – 16)
71-72 Old Elephant Road
Eskaton Garden, Dhaka 1000
Telephone: +8802 551 38598-9 (PABX), +8802 551 38753-5
Facsimile: +8802 551 38752
Website: www.seip-fd.gov.bd
CBLM – Plumbing (Student Guide) v.1 Oct 2018 5
Skills for Employment Investment Programme (SEIP)
How to Use this Competency-based Learning Material
Welcome to the competency-based learning material for Plumbing for use in construction works. These
modules contain training materials and learning activities for you to complete in order to become competent
and qualified as a skilled worker.
There are seven (7) modules that make up this course which comprises the skills, knowledge and attitudes
required to become a skilled worker including:
1. Perform pipe threading operation
2. Perform access cutting and encroachment works
3. Carry out water supply line installation using G.I, PPR/HDP pipes
4. Carry out water supply line installation using PVC/UPVC pipes
5. Carry out sewer pipe line installation
6. Carry out plumbing fixtures installation
7. Perform pressure testing of piping system
As a learner, you will be required to complete a series of activities in order to achieve each learning
outcome of the module. These activities may be completed as part of structured classroom activities or
simulated workplace demonstrations.
These activities will also require you to complete associated learning and practice activities in order to gain
the skills and knowledge needed to achieve the learning outcomes. You should refer to Learning Activity
pages of each module to know the sequence of learning tasks and the appropriate resources to use for
each task.
This page will serve as the road map towards the achievement of competence. If you read the Information
Sheets, these will give you an understanding of the work, and why things are done the way they are. Once
you have finished reading the Information Sheets, you will then be required to complete the Self-Check
Quizzes.
The self-check quizzes follow the Information Sheets in this learning guide. Completing the self-check
quizzes will help you know how you are progressing. To check your knowledge after completion of the
Self-Check Quizzes, you can review the Answer Key at the end of each module.
You are required to complete all activities as directed in the Learning Activity and Information Sheet.
This is where you will apply your newly acquired knowledge while developing new skills. When working,
high emphasis should be laid on safety requirements. You will be encouraged to raise relevant queries or
ask the facilitator for assistance as required.
When you have completed all the tasks required in this learning guide, formal assessment will be scheduled
to officially evaluate if you have achieved competency of the specified learning outcomes and are ready for
the next task.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 6
Skills for Employment Investment Programme (SEIP)
List of Icons
Icon Name Icon
Module content
Learning outcomes
Performance criteria
Contents
Assessment criteria
Resources required
Information sheet
Self-check Quiz
Answer key
Activity
Video reference
Learner job sheet
Assessment plan
Review of competency
CBLM – Plumbing (Student Guide) v.1 Oct 2018 7
Skills for Employment Investment Programme (SEIP)
Module 1: Perform pipe threading operation
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to perform pipe threading
operation for plumbing works in construction which includes gathering and
checking tools, equipment and materials, carrying out steel pipe cutting
operation, carrying out thread cutting operation, assembling pipe run, and
cleaning and maintaining the work area. It also includes information sheets,
activity sheets, job sheets, self-check quizzes and answer keys.
Nominal Duration: 40 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
1.1 Gather and check tools, equipment and materials
1.2 Carry out steel pipe cutting operation
1.3 Carry out thread cutting operation
1.4 Assemble pipe run
1.5 Clean/maintain the work area
Performance Criteria:
1. Required pipe size and dimensions are identified in accordance to plumbing plan/design
2. Pipes are selected and gathered in accordance to specification
3. Personal protective equipment (PPE) is selected and used
4. Tools, equipment and materials are selected, gathered and checked for usability
5. Pipes are measured and marked in accordance to plumbing plan/drawing specification
6. Steel pipes are clamped and fixed using appropriate clamping device
7. Pipe run length is measured and cut using appropriate cutting tool
8. Pipes are cut in accordance with plumbing plan/drawing and the type of attachment fittings
9. Pipe run length is measured within the specified tolerance
10. Newly cut pipe is de burred/removed of burr using appropriate de burring tool
11. Diestocks are adjusted and initiated into the pipe end squarely
12. Thread cutting is carried out on pipes in accordance to workplace procedure
13. Coolant is used during thread cutting operation
14. Pipes are laid down in accordance with the planned/designed pipe run
15. Pipes and pipe fittings are assembled and fixed in accordance with planned/designed pipe run
16. Pipes, fittings and pipe runs are checked for damage/quality of work
17. Plumbing tools/equipment are cleaned and checked for operability
18. Work area is cleaned, and waste materials are disposed of in accordance with workplace requirements
CBLM – Plumbing (Student Guide) v.1 Oct 2018 8
Skills for Employment Investment Programme (SEIP)
Learning Outcome 1.1 - Gather and Check Tools, Equipment and Materials
Contents:
▪ Names of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask and ear plug
▪ List of main tools, equipment and materials uses
Assessment criteria:
1. Required pipe size and dimensions are identified in accordance to plumbing plan/design. 2. Pipes are selected and gathered in accordance to specification. 3. Appropriate personal protective equipment (PPE) is selected and used. 4. Necessary tools and equipment are selected, gathered and checked for usability.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape and plumbing plan/drawing
Learning Activity 1.1.1
Learning Activity Resources/Special Instructions/References
Gather and check tools, equipment and
materials
▪ Information Sheet: 1.1.1 ▪ Self-Check Quiz: 1.1.1 ▪ Answer Key: 1.1.1 ▪ https://www.youtube.com/watch?v=hZbp-s3LJYo
Information Sheet 1.1.1
Learning Objective: to identify and uses of the personal protective equipment in the workplace.
Personal Protective Equipment:
When undertaking plumbing works, the following personal protective equipment (PPE) should be worn:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 9
Skills for Employment Investment Programme (SEIP)
Safety Helmets:
A hard hat is a type of helmet used in workplace
environments to protect the head from injury due
to falling objects.
Eye Protector/Goggles/Safety Glasses:
Goggles are forms of protective eyewear that
usually enclose or protect the eye area.
Ear plugs/ear muffs:
An earplug is used to protect the user's ears from
loud noises or the intrusion of water, foreign
bodies, dust or excessive wind.
Dust Mask:
Dust mask is necessary for dust protection in
workplace.
Safety cloth (overalls)/apron:
Apron has been designed to protect the body
from injury in the workplace.
Safety vest:
This is reflective safety equipment used to
increase visibility of a worker.
Safety belt:
This is used for fall protection of construction
worker and also used for additional tools holding
effective for high-rise building.
Safety harness:
A belt/body harness is designed to catch and
secure a person in case of falling while working
at height level.
Hand gloves:
These are used to protect the hands while
working and safeguarding of hands.
Safety shoes/Footwear/Boots:
Safety shoes are used to protect the legs/feet
from any harms or injuries.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 10
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 1.1.1
Check your understanding by answering the following questions:
Fill in the blanks with the correct answer: 1. ______________ is used to protect eyes from flying particles which may cause injury to the worker.
2. ______________ is reflective and visible used by construction workers.
3. ______________ is used to protect the hands when working.
4. ______________ used to protect one’s feet from sharp object to fall.
5. ______________ protects workers to fall and also holds additional tools.
Learning Activity 1.1.2
Learning Activity Resources/Special Instructions/References
Gather and check tools, equipment and
materials
▪ Information Sheet: 1.1.2, 1.1.3, 1.1.4 ▪ Self-Check Quiz: 1.1.2, 1.1.3, 1.1.4 ▪ Answer Key: 1.1.2, 1.1.3, 1.1.4 ▪ https://www.globalindustrial.com/c/plumbing/plumbing-
tools ▪ https://www.plumbingsupply.com/tools.html
Information Sheet 1.1.2
Learning Objective: to identify, gather and check usability of tools and equipment used for distempering
works.
Tools and equipment:
To perform plumbing works, it requires use of the following tools and equipment:
Measuring tape:
This is used to measure items.
Steel rule:
Steel rules are the most widely used measuring
tools. Marking Pencil/Pen/Chalk:
These are used to marking out on the material for a required measurement
CBLM – Plumbing (Student Guide) v.1 Oct 2018 11
Skills for Employment Investment Programme (SEIP)
Pencil
Pen
Chalk
Callipers:
A Vernier/slide callipers/callipers is a handy instrument used to measure diameter of a pipe and can
also be measure the thickness of pipe.
Vernier/slide callipers
Inside calliper
Outside calliper
Adjustable wrench:
An adjustable wrench allows you to work with
many different sizes without having to change
tools.
Pipe wrench:
The pipe wrench is an adjustable wrench used
for turning metal pipes and fittings with a rounded
surface.
Monkey wrench:
Used to loosen and tighten the pipes and bolts
Combination pliers:
Combination pliers or pliers are used to cut wire
etc.
Die stocks:
This Die Stock is designed for threading using
separate "drop heads" for each size required.
Pipe cutter:
Pipe cutter is a manual or hand tool mainly used
for cutting the metal pipes of different diameter.
Scissors type pipe cutter:
A scissors type pipe cutter is mainly used to cut
PPR. Occasionally it is used to cut PVC pipes
too.
Hacksaw:
The tool is mainly used in cutting metals like
plates, pipes, rods, bars, angles with minimal
thickness, width and length. Sometimes this tool
is used for cutting plastic pipes and other
materials that suit to its purpose.
Pipe vice:
A pipe vice is a plumbing tool used to hold pipe or
tube securely so that it can be cut or threaded.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 12
Skills for Employment Investment Programme (SEIP)
Screw drivers:
These are used to loosen and tighten the screws. The type depends on the shape of slot head of the
screws.
Flared
Phillips
Ratchet
Spirit level:
It is used to check for level of horizontal, vertical
and 45 degree angular surfaces.
Pipe reamer:
A reamer is used to remove internal burrs from
the ends of the cut pipe. The reamer is available
as either as a simple hand held tool or to be fitted
into a brace.
Files (flat, half round, round):
Files are cutting tools used to remove/smooth rough and sharp edges from cut metal. They are also
used to file metal to shape or size.
Flat file
Half-round file
Round file
Hammer:
A hammer is a tool or device that delivers a blow to an object. Most hammers are hand tools used to
drive nails, fit parts, forge metal, and break apart objects. Hammers vary in shape, size, and structure,
depending on their purposes.
Ball peen hammer
Claw hammer
Mallet
Sledge hammer
Cold chisel:
A cold chisel is used mainly for chipping away at
old mortar, concrete, cement, and plaster.
Steel wire brush:
A wire brush is a tool consisting of a brush whose
bristles are made of wire, most often steel wire.
Oil can:
An oil can is usually holding motor oil
for lubricating machines. It also be used to fill oil-
based lanterns.
Individual Activity:
▪ Identify the tools and equipment used in plumbing works
▪ Check the usability/function ability of the tools and equipment
CBLM – Plumbing (Student Guide) v.1 Oct 2018 13
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 1.1.2
Check your understanding by answering the following questions:
No. Write the name of the tools given
below
Name
1
2
3
4
5
Information Sheet 1.1.3
Learning Objective: to identify, uses and check of tools, equipment and materials in plumbing works.
Tools and equipment:
No. Picture Name and Used for
1
Drill Machine
Drilling holes in masonry, steel and timber surfaces
2
Angle Grinder
Cutting brickwork and steel grinding steel surfaces
3
PPR Welding Device
Fusion welding of PPR pipes and fittings
CBLM – Plumbing (Student Guide) v.1 Oct 2018 14
Skills for Employment Investment Programme (SEIP)
4
Heat Gun
Heat up area to be worked on
5
Breaker Machine
Demolish masonry, concrete areas required
6
Scanner
Scan the surface for any cables or conduit
7
PPR pipe cutter
Used to cut PPR pipes to the required length
Self-Check Quiz 1.1.3
Check your understanding by answering the following questions:
No. Picture Used for
1
2
3
4
5
Information Sheet 1.1.4
Learning Objective: to identify, uses and check of tools, equipment and materials in plumbing works.
Materials:
1
Teflon tape is used to seal the thread of pipes
CBLM – Plumbing (Student Guide) v.1 Oct 2018 15
Skills for Employment Investment Programme (SEIP)
2
Hemp is a fibre that it is the traditional method of aiding the
sealing of heavier gauge pipe work. It must be used in
conjunction with a suitable paste sealant
3
Solvent cement and primer is used to glue cpvc/pvc/ uPVC
joints
Self-Check Quiz 1.1.4
Check your understanding by answering the following questions:
1. Why Teflon tape is used in plumbing works?
2. What is Hemp?
CBLM – Plumbing (Student Guide) v.1 Oct 2018 16
Skills for Employment Investment Programme (SEIP)
Learning Outcome 1.2 - Carryout Steel Pipe Cutting Operation
Contents:
▪ Pipes and their uses: galvanized iron (GI) pipe, PVC pipe, stainless steel (SS) pipe, Boehringer Ingelheim (BI) pipe and cast iron (CI) pipe
▪ Fittings and their uses: elbow 90°, Elbow 45°, tee, coupling, nipple, plug, cap, socket etc. ▪ Steel pipe cutting procedures
Assessment criteria:
1. Pipes are measured and marked in accordance to plumbing plan/drawing specification.
2. Steel pipe is clamped using appropriate clamping device.
3. Pipe run length is measured and cut using appropriate cutting tool.
4. Pipe length is measured and cut in accordance with plumbing plan/drawing and the type of attachment fittings.
5. Pipe run length is measured within the specified tolerance.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape and plumbing plan/drawing ▪ Pipes: GI pipe, PVC pipe, stainless steel pipe, BI pipe and cast iron pipe ▪ Fittings: elbow 90° & 45°, tee, coupling, nipple, plug, cap and socket etc.
Learning Activity 1.2.1
Learning Activity Resources/Special Instructions/References
Carryout steel pipe cutting operation ▪ Information Sheet: 1.2.1, 1.2.2 ▪ Job Sheet 1 ▪ Self-Check Quiz: 1.2.1, 1.2.2 ▪ Answer Key: 1.2.1, 1.2.2 ▪ https://en.wikipedia.org/wiki/Pipe_Cutting
CBLM – Plumbing (Student Guide) v.1 Oct 2018 17
Skills for Employment Investment Programme (SEIP)
Information Sheet 1.2.1
Learning Objective: to identify and uses of different types of pipes in a workplace.
Pipes:
GI (Galvanised Iron) pipes: These pipes are much stronger
and economical, used to transfers water in various
plumbing applications.
Poly Propylene Random (PPR) Pipe: These are the best
pipes used to transfer hot and cold water.
PVC (polyvinyl chloride) pipe: These are common, strong
but lightweight plastic pipe used in construction, only for
cold water.
uPVC (Un-plasticized polyvinyl chloride) pipe: If no
plasticizers are added, it is known as uPVC (un-plasticized
polyvinyl chloride), rigid PVC.
MS (Mild Steel) pipes: These are heavy duty and costly
pipes used to transfers gas / water in various plumbing
applications.
SS (Stainless Steel) pipes: These are also heavy duty and
costly pipes used to transfers gas / water in various
plumbing applications.
CI (Cast Iron) pipes: These are most suitable and used for
rain water disposal and waste water disposal etc.
Copper pipes: These pipes are used for industrial
purposes for heavy flows.
Concrete pipes: For heavy drainage water disposal,
concrete pipes of large diameters are used. Smaller
diameter pipes are used for small flows.
Asbestos Cement Pipes: These pipes are used as vent
pipes, soil pipes and rain water pipes. They are very cheap
compared to all but they can break easily.
High Density Polyethylene (HDP) pipes: This pipe is used
for water supply, waste water disposal and as electrical
conduit.
1
CBLM – Plumbing (Student Guide) v.1 Oct 2018 18
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 1.2.1
Check your understanding by answering the following questions:
No. Different types of Pipe Name of the pipe
1
2
3
4
5
Information Sheet 1.2.2
Learning Objective: to identify and uses of different types of plumbing fittings in the workplace.
Elbow:
Elbow is used to join two lengths of pipe (equal or un-
equal diameter).
Bend:
Bend is used to join two lengths of pipe (equal or un-
equal diameter).
Tee (T):
Tee is used to connect three lengths of pipe (equal or
un-equal diameter) comes in a number of sizes.
Union:
Union is used to connect two pipe lengths together
comes in a number of sizes. It is used where a pipe line
is opened to replace a damaged section or to cut into an
existing line.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 19
Skills for Employment Investment Programme (SEIP)
Reducer:
Reducer is used to join two different size pipes in a straight way.
Socket:
Socket is used to connect two pipe lengths together comes in a number of sizes.
Nipple:
A nipple is used between two fittings.
Bush:
A bush is used to connect the male end of a pipe to a fitting of larger or smaller diameter pipe.
Adapter (male/female):
An adapter is used to connect the threaded end of a pipe to a fitting.
Plug:
Plug is used to seal off a GI fitting.
Cap:
Cap is used to seal off pipe end.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 20
Skills for Employment Investment Programme (SEIP)
JOB SHEET 1
Qualification: Plumbing
Learning unit: Perform pipe cutting operation:
Cut G I/PVC/uPVC/PPR/CI pipes
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: G I/PVC/uPVC/PPR/CI pipes, lubricant
Tools and equipment: Measuring tape, foot rule, hack saw, hack saw, marker pen, pipe cutter, pipe vice, 3-wheel type pipe cutter, C I chain cutter
Performance criteria: For G. I/PVC/uPVC/PPR pipes: For C.I pipes:
1. Cut the GI / PVC/uPVC/PPR pipe with a hacksaw / pipe cutter
2. Measurement error must be within approximately 2mm
3. Pipes must be cut uniformly one end to another end
1. Cut Cast Iron pipe using a single stroke chain cutter
2. Measurement error must be within approximately 2mm
3. Pipes must be cut uniformly one end to another end
Measurement: Cut GI pipe as per drawing using
hacksaw and 3-wheel type cutters.
Cut PVC/uPVC/PPR pipe as per
drawing using hacksaw.
Cut a C I soil pipe 500mm long from
the flanged fitting using a single
stroke Chain cutter
Procedure: 1. Identify the type pipe required 2. Measure, cut using a hacksaw as
per measurement on drawing 2 x 450 mm lengths of 20mm ɸ GI pipe.
3. Measure, cut using a 3-wheel type pipe cutter 1 x 250mm length 20mm ɸ PVC pipe.
4. 1 x 450 mm lengths of 20mm ɸ PVC pipe.
5. All pipes must be cut uniformly one end to another end.
6. Measurement error must be within approx. 2mm
1. Identify the fittings and pipe required
2. Measure, cut a 1 X 500 mm length of 100 mm ɸ C I pipe.
3. Pipes must be cut uniformly one end to another end.
4. Measurement error must be within approx. 2mm
CBLM – Plumbing (Student Guide) v.1 Oct 2018 21
Skills for Employment Investment Programme (SEIP)
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
Individual Activity:
▪ Watch the video on ‘How to cut water supply pipes’ and summarise the key points (if facilities available)
▪ Cut the pipes following the Job Sheet 1 (see above)
Self-Check Quiz 1.2.2
Check your understanding by answering the following questions:
Read the following statements and mark whether true or false accordingly:
No. Description True False
1. Elbow is used to join three lengths of pipe (equal or un-equal diameter)
2. Tee is used to connect two lengths of pipe (equal or un-equal diameter)
comes in a number of sizes
3. Union is used, where a pipe line is opened to replace a damaged section or
to cut into an existing line
4. Reducer is used to join two different size pipes in a straight way
5. Socket is used to connect three pipe lengths together comes in a number of
sizes
6. A nipple is used between two fittings
7. A bush is used to connect the male end of a pipe to a fitting of larger or
smaller diameter pipe
8. An adapter is used to connect the threaded end of a pipe to a fitting
9. Cap is used to seal off a GI fitting
10. Plug is used to seal off pipe end
CBLM – Plumbing (Student Guide) v.1 Oct 2018 22
Skills for Employment Investment Programme (SEIP)
Learning Outcome 1.3 – Carry Out Thread Cutting Operation
Contents:
▪ De-burring tool uses: flat file, round file, half round file. pipe reamer and sandpaper ▪ Coolant: water, oil, air, synthetic, nitrogen ▪ Thread cutting procedure
Assessment criteria:
1. Steel/metal pipes are clamped and fixed using pipe vice.
2. Newly cut pipe is de burred/removed of burr using appropriate de burring tool.
3. Diestocks are adjusted and initiated into the pipe end squarely.
4. Thread cutting is carried out on pipes in accordance to workplace procedure.
5. Coolant is used during thread cutting operation.
6. Threads are checked to conform with the specified form and measured in accordance with
plan/drawing.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape and plumbing plan/drawing
▪ Pipes: GI pipe, PVC pipe, stainless steel pipe, BI pipe and cast-iron pipe
▪ Fittings: elbow 90° & 45°, tee, coupling, nipple, plug, cap and socket etc.
Learning Activity 1.3.1
Learning Activity Resources/Special Instructions/References
Carryout thread cutting operation ▪ Information Sheet: 1.3.1 ▪ Specification Sheet 1 ▪ Job Sheet 2 ▪ Self-Check Quiz: 1.3.1 ▪ Answer Key: 1.3.1 ▪ https://en.wikipedia.org/wiki/Threading_(manufacturing) ▪ https://www.instructables.com/id/Thread-Cutting-Internal-and-
External-on-a-
CBLM – Plumbing (Student Guide) v.1 Oct 2018 23
Skills for Employment Investment Programme (SEIP)
Information Sheet 1.3.1
Learning Objective: to identify and uses of pipe vice, de burring tool, diestocks and coolant in the
workplace.
Pipe vice:
A pipe vice is a plumbing tool used to hold pipe or tube
securely so that it can be cut or threaded.
De burring tools:
Files (flat, half round, round): Files are cutting tools used to remove/smooth rough and sharp edges
from cut metal. They are also used to file metal to shape or size.
Flat file
Half-round file
Round file
Pipe reamer:
A reamer is used to remove internal burrs from the ends
of the cut pipe. The reamer is available as either as a
simple hand held tool or to be fitted into a brace.
Sand paper:
Sand paper is used as a de burring tool. It is available
with various grades.
Die stocks:
This Die Stock is designed for threading using separate
"drop heads" for each size required.
Coolant:
In plumbing system coolant plays important role. Water, oil, air, synthetic and nitrogen etc. used as
coolants.
SPECIFICATION SHEET 1
Thread Length Data:
Nominal Pipe
Size (in inches)
Threads
Per Inch
Approximate
Length of Thread
(In Inches)
Approximate
Numbers of
Threads to be Cut
Approximate Total Thread
Makeup Engagement (In
Inches)
½ 14 ¾ 10 7/16
3/4 14 ¾ 10 ½
1 11 ½ ⅞ 10 9/16
1 ½ 11 ½ 1 11 9/16
2 11 ½ 1 11 5/8
2½ 8 1½ 12 ⅞
3 8 1½ 12 1
4 8 15/8 13 11/16
6 8 1¾ 14 13/16
CBLM – Plumbing (Student Guide) v.1 Oct 2018 24
Skills for Employment Investment Programme (SEIP)
JOB SHEET 2
Qualification: Plumbing
Learning unit: Perform pipe threading operation:
Cut an external thread of 14 TPI on a ¾ inch G I pipe
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: G I pipe, lubricant
Tools and equipment: Die Stock and pipe vice, round and flat files
Measurement:
Notes:
• Cut an external thread of 14 TPI on a ¾ inch GI pipe.
• The thread must be uniform
• No threads are to be broken
• Thread when be cut to be visible 1 to 2 threads of the die stock
• Lubricant to be applied during threading operation
Procedure: 1. Collect tools, materials and equipment. 2. Place pipe vice on the ground 3. Fix the GI pipe into the vice 4. Adjust die stock as per diameter of the pipe 5. Insert die stock into the pipe 6. Rotate the die stock in clockwise direction. 7. Apply lubricant on the pipe. 8. Rotate the die stock anticlockwise after 4 to 5 times clockwise 9. Cut thread until one or two threads out of die is visible. 10. Remove the die set from the pipe. 11. Clean thread and workplace 12. Restore all tools and materials
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 25
Skills for Employment Investment Programme (SEIP)
Individual Activity:
▪ Watch the video on ‘How to cut external thread on a GI pipe’ and summarise the key points (if facilities available)
▪ Cut the pipes following the Job Sheet 2 (see above)
Field Visit:
• Visit a construction site working with plumbing works in the neighbourhood
• Observe some activities there like:
- What tasks are being performed?
- Which tools are being used and for what purpose?
- Are the workers worn adequate PPE? List out the names
- Anything more observed you may mention
• Fill-up the ‘Field Visit Format’ given and submit to your trainer
• Present the experience group wise as per instruction of your trainer
CBLM – Plumbing (Student Guide) v.1 Oct 2018 26
Skills for Employment Investment Programme (SEIP)
Learning Outcome 1.4 - Assemble Pipe Run
Contents:
▪ Plan and design of pipe run ▪ Assembling procedure ▪ Checking for damage/quality check of pipes, fittings and pipe run
Assessment criteria:
1. Pipes are laid down in accordance with the planned/designed pipe run.
2. Pipes and pipe fittings are assembled and fixed in accordance with planned/designed pipe run.
3. Pipes, fittings and pipe runs are checked for damage/quality of work.
4. Assembled pipe runs are measured/checked within tolerable dimensions/length in accordance with
design/specification.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape and plumbing plan/drawing ▪ Pipes: GI pipe, PVC pipe, stainless steel pipe, BI pipe and cast iron pipe ▪ Fittings: elbow 90° & 45°, tee, coupling, nipple, plug, cap and socket etc.
Learning Activity 1.4.1
Learning Activity Resources/Special Instructions/References
Assemble pipe run ▪ Information Sheet: 1.4.1 ▪ Self-Check Quiz: 1.4.1 ▪ Answer Key: 1.4.1 ▪ https://www.todayshomeowner.com/video/how-to-align-pvc-pipe-fitting-
during- ▪ https://www.youtube.com/watch?v=fWiXTr-6N4I ▪ https://www.youtube.com/watch?v=eMQRX2yXIsE
CBLM – Plumbing (Student Guide) v.1 Oct 2018 27
Skills for Employment Investment Programme (SEIP)
Information Sheet 1.4.1
Learning Objective: list the tools, equipment and materials required for making pipe joints, explain the
necessity of assembling pipe run, and describe the procedure of assembling pipe run.
On completion of this task you will be able to complete the following steps:
1. Collect tools, equipment and materials. 2. Cut the pipe as per required measurement with pipe cutter or hack saw. 3. Lay down the pipes in accordance with the planned/designed pipe run.
4. Assembled and fixed the pipes and pipe fittings in accordance with planned/designed pipe run.
5. Temporarily join pipes and fittings and make sure that the pipe in the run is facing the right direction.
6. Use a felt-tip pen to make alignment marks on all the joints where the fitting must face correctly.
7. Disassemble, keeping careful track of the order of installation.
8. Apply primer to each pipe end and each fitting.
9. Apply solvent/cement and join each pipe in order.
10. Checked the pipes, fittings and pipe runs for damage/quality of work.
11. Assembled pipe runs are measured/checked within tolerable dimensions/length in accordance with
design/specification.
12. Conduct leakage test using water. 13. Clean the workplace. 14. Restore the tools equipment and materials.
PVC Drainage Pipe Joints
PVC Pipe Joints
PPR Pipe Joints
GI Pipe Joints
CBLM – Plumbing (Student Guide) v.1 Oct 2018 28
Skills for Employment Investment Programme (SEIP)
Individual Activity:
▪ Watch the videos on ‘How to bend PVC’ and summarise key points (if facilities available) ▪ Watch the videos on ‘How to PPR’ and summarise key points
▪ Complete the assigned jobs as per drawing/instructions
Assignment:
The trainee will identify the following pictures and submit to the trainer. Pictures can be collected from the
market, net or other sources. They should be neatly put in a file with names and uses.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 29
Skills for Employment Investment Programme (SEIP)
Learning Outcome 1.5 - Clean and Maintain the Work Area
Contents:
▪ Importance and necessity of cleaning tools and equipment and workplace ▪ Methods of cleaning, tools and equipment required for cleaning
• Lubricants
• Advantages of proper storing of tools and equipment; types of storage
Assessment criteria:
1. Plumbing tools and equipment are cleaned and maintained.
2. Work area is cleaned.
3. Waste materials are disposed of in accordance with workplace requirements.
Resources required:
Students/trainees must be provided with the following resources:
• Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Cleaning tools and equipment: dusters, dust pans, mops, polishing clothes, brooms, brushes, buckets, dust bins and cotton rags
▪ Materials: water, detergents, abrasives, bleaches and lubricants (oil, grease and powder)
Learning Activity 1.5.1
Learning Activity Resources/Special Instructions/References
Clean and maintain the work area
▪ Information Sheet: 1.5.1 ▪ Self-Check Quiz: 1.5.1 ▪ Answer Key: 1.5.1 ▪ https://www.wikihow.life/Clean-a-House ▪ https://www.goodhousekeeping.com/home/cleaning/g2550/best-
cleaning-
Information Sheet 1.5.1
Learning Objective: to clean and lubricate necessary tools and equipment and store the same as per
standard procedures and clean workplace.
General information:
After plumbing works cleaning is very important and essential for both tools and equipment used and the workplace where plumbing work has done. To keep the tools and equipment clean, extra attention and
CBLM – Plumbing (Student Guide) v.1 Oct 2018 30
Skills for Employment Investment Programme (SEIP)
experience required considering how to remove dirt, including dust, stains, bad smells, and clutter on surfaces. For this, we can use some cleaning agents as follows:
▪ Water (the best cleaning agent)
▪ Soap or detergent
▪ Calcium hypochlorite (powdered bleach)
▪ Sodium hypochlorite (liquid bleach)
▪ Acetic acid (vinegar)
Methods of cleaning: cleaning can be done with following methods:
▪ Dusting
▪ Shaking and beating
▪ Sweeping
▪ Mopping
▪ Washing
▪ Polishing
Rough Cleaning:
▪ First remove all debris either by hand or use of brushes, brooms, scrapers, squeegees etc.
▪ Collect and dispose of all debris appropriately.
▪ A warm rinse is recommended to complete the rough cleaning.
Removal of Excess Water:
▪ Any areas where water has extensively pooled may serve as a medium for bacteria growth and should be dried.
▪ Equipment that has the potential to rust should also be dried. Tools and equipment for cleaning:
Broom:
A broom is a cleaning tool consisting of usually stiff fibres, also known as coconut broom.
Dusters/Dust protector:
A duster/dust protector is a light, loose-fitting long coat.
Dust pan:
A dustpan is used in combination with a broom. It is used to collect dust/waste/small debris.
Cleaning brushes:
Cleaning brushes are tool with bristles, wire or other filaments, used for cleaning, painting, and surface finishing, and for many other purposes.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 31
Skills for Employment Investment Programme (SEIP)
Mop:
A mop is a bundle of coarse strings or a piece of cloth, sponge, or other absorbent material, attached to a stick. It is used to soak up liquid, for cleaning floors and other surfaces, to mop up dust, or for other cleaning purposes.
Waste container:
A waste container is a container for temporarily storing waste and is usually made out of metal or plastic. Some common terms are dustbin, garbage can, trash can and dumpster.
Cotton rags:
A rag is a piece of old cloth which can be used to clean or wipe things.
Lubricant:
• A lubricant is used to reduce friction between surfaces.
• Adequate lubrication allows smooth operation of equipment, reduces the rate of wear and prevents excessive stresses.
Advantages of proper storage of tools and equipment:
▪ Ensures that tools and equipment remain in good condition and last for a long time. ▪ Easy to find when needed and are less likely to be lost. ▪ Productivity is increased because time is not lost looking for tools and equipment.
Common types of storage:
Cabinets
Bin
Tool box
Bucket bag
Tote bag
Storage bag
Tool racks
Work bench
Shelving
CBLM – Plumbing (Student Guide) v.1 Oct 2018 32
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 1.5.1
Check your understanding by answering the following questions:
1. What are the methods of cleaning?
2. What is a broom?
3. Write the uses of mops.
4. What is the common type of storage for plumbing tools and equipment?
5. What are the advantages of properly storing plumbing tools and equipment?
CBLM – Plumbing (Student Guide) v.1 Oct 2018 33
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 1.1.1
1. Eye protector/goggles/safety glasses
2. Safety vest
3. Hand gloves
4. Safety shoes/footwear/boots
5. Safety belt
Answer Key 1.1.2
1. Pipe wrench 2. Die stocks 3. Pipe cutter 4. Scissors type pipe cutter 5. Pipe reamer
Answer Key 1.1.3
1. Drilling holes in masonry, steel and timber surfaces. 2. Cutting brickwork and steel grinding steel surfaces. 3. Fusion welding of PPR pipes and fittings. 4. Heat up area to be worked on. 5. Cut PPR pipes to the required length by cutter.
Answer Key 1.1.4
1. Teflon tape is used to seal the thread of pipes. 2. Hemp is a fibre type material that is used for sealing of heavier gauge pipe work.
Answer Key 1.2.1
1. GI (Galvanised Iron) 2. Poly Propylene Random (PPR) 3. PVC (Polyvinyl Chloride) 4. Concrete 5. Copper
Answer Key 1.2.2
1. False 2. False 3. True 4. True 5. False 6. True 7. True 8. True 9. False 10. False
Answer Key 1.5.1
1. Methods of cleaning are: dusting, shaking and beating, sweeping, mopping, washing, polishing.
2. A broom is a cleaning tool consisting of usually stiff fibres, also known as coconut broom.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 34
Skills for Employment Investment Programme (SEIP)
3. Mops are used to soak up liquid, for cleaning floors and other surfaces, to mop up dust, or for other
cleaning purposes.
4. Tool rack is a common type of storage of painting tools and equipment.
5. The advantages of properly storing plumbing tools and equipment are: ensure good condition, last
for a long time, easily find, less likely to be lost and increase productivity.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 35
Skills for Employment Investment Programme (SEIP)
Module 2: Perform access cutting and encroachment works
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to perform access
cutting and encroachment works which includes interpreting drawings and
plumbing plans, inspecting encroachment work area, gathering tools,
equipment and materials, cutting and making access through walls and floors,
and cleaning and maintaining the work area. It also includes information
sheets, activity sheets, job sheets, self-check quizzes and answer keys.
Nominal Duration: 32 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
2.1 Interpret drawings and plumbing plans
2.2 Inspect encroachment work area
2.3 Gather tools, equipment and materials
2.4 Cut and make access through walls and floors
2.5 Clean/maintain the work area
Performance Criteria:
1. Building drawing/plumbing plan is collected and correctly interpreted.
2. Work area/line of encroachment and the possible obstructions/limitations along the line of encroachment work are identified.
3. Obstructions/limitations are planned out.
4. Tools, equipment and materials are selected, gathered and checked for usability.
5. Appropriate personal protective equipment (PPE) is selected, checked and used.
6. Lay out for access/encroachment work is properly made.
7. Wall and floor are cut to create pipe access/encroachment as per workplace requirements.
8. Cutting walls and floors are made without causing damage to the wall or floor and adjacent installations.
9. Used tools and equipment are cleaned and maintained.
10. Work area is cleaned and waste materials are disposed in accordance with workplace requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 36
Skills for Employment Investment Programme (SEIP)
Learning Outcome 2.1 - Interpret Drawings and Plumbing Plans
Contents:
▪ Building drawing: detail plumbing plan, elevation and section ▪ Encroachment of floor, wall, ceiling, slab, beam and column
Assessment criteria:
1. Building drawing/plumbing plan is collected.
2. Building drawing/plumbing plans are interpreted.
3. Work area/line of encroachment is identified.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, hacksaw, cold chisel, hammer ▪ Equipment: power hacksaw, electric drill machine
• Materials: soft stone (marker), marking pen, pencil, masking tape and plumbing plan/drawing
Learning Activity 2.1.1
Learning Activity Resources/Special Instructions/References
Interpret drawings and plumbing plans ▪ Information Sheet: 2.1.1 ▪ Self-Check Quiz: 2.1.1 ▪ Answer Key: 2.1.1 ▪ https://en.wikipedia.org/wiki/Plumbing_drawing
CBLM – Plumbing (Student Guide) v.1 Oct 2018 37
Skills for Employment Investment Programme (SEIP)
Information Sheet 2.1.1
Learning Objective: to identify encroachments and interpret the building drawing/plumbing plans used in
the workplace.
Building drawing:
Building drawing is an essential part for
plumbing works. It requires calculating the
quantity of water to be supplied for the
dwellers to ensure at different locations. So, it
needs to study the drawing/plumbing plans or
sections, identify the source of water and line
of encroachment for a successful installation
of different kinds of plumbing fixtures.
Typical Plumbing System of a 3-Storeyed Building
CBLM – Plumbing (Student Guide) v.1 Oct 2018 38
Skills for Employment Investment Programme (SEIP)
Line of encroachment: in a plumbing system, the line of encroachment may include floors, walls, ceilings, slabs, beams, columns etc.
Self-Check Quiz 2.1.1
Check your understanding by answering the following questions:
1. Write the line of encroachment in plumbing works.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 39
Skills for Employment Investment Programme (SEIP)
Learning Outcome 2.2 - Inspect Encroachment Work Area
Contents:
▪ Obstructions/limitations along the line of encroachment: built in appliance, cabinet, concrete column and beam, doors, widows and existing pipe run
▪ Possible solutions/remedies to overcome
Assessment criteria:
1. Possible obstructions/limitations along the line of encroachment work are identified.
2. Possible solutions/remedies needed for identified.
3. Obstructions/limitations are planned out.
4. Tools, equipment and materials required to carry out encroachment work are identified.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, cold chisel, claw hammer, mallet adjustable wrench, box set wrench, pipe wrench, pliers, hacksaw, spirit level
▪ Equipment: jack hammer, drill press, angle grinder, portable drill, oxy-acetylene cutting outfit and welding machine
▪ Materials: soft stone (marker), marking pen, pencil, welding rod, cement, sand, putty
Learning Activity 2.2.1
Learning Activity Resources/Special Instructions/References
Inspect encroachment work area ▪ Information Sheet: 2.2.1 ▪ http://www.donleyservice.com/media/articles/2018/03/how-
plumbers-fix-tre
Information Sheet 2.2.1
Learning Objective: to inspect encroachment work area for plumbing fixtures installation.
Obstructions/limitations:
In plumbing system along the line of encroachment we commonly met the following possible obstructions/limitations:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 40
Skills for Employment Investment Programme (SEIP)
▪ Built in appliance ▪ Cabinet ▪ Concrete column ▪ Concrete beam ▪ Doors ▪ Widows ▪ Existing pipe run etc.
How to overcome obstructions/limitations:
In plumbing system to overcome obstructions/limitations the following actions should be done:
▪ Collect and study the building plan and plumbing design/drawing ▪ Identify the line of encroachment ▪ Identify and planned out the obstructions/limitations ▪ Report and discuss with the immediate superior ▪ Determine the possible solutions/remedies to overcome obstructions/limitations ▪ Make a list of tools, equipment and materials to carry out the encroachment works
CBLM – Plumbing (Student Guide) v.1 Oct 2018 41
Skills for Employment Investment Programme (SEIP)
Learning Outcome 2.3 – Gather Tools, Equipment and Materials
Contents:
▪ List of main tools, equipment and materials uses ▪ Name of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves,
safety glasses, safety belt, apron, dust mask, ear plug
Assessment criteria:
1. Necessary tools, equipment and materials are selected, gathered and checked for usability. 2. Appropriate personal protective equipment (PPE) is checked and used.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, cold chisel, claw hammer, mallet adjustable wrench, box set wrench, pipe wrench, pliers, hacksaw, spirit level
▪ Equipment: jack hammer, drill press, angle grinder, portable drill, oxy-acetylene cutting outfit and welding machine
▪ Materials: soft stone (marker), marking pen, pencil, welding rod, cement, sand, putty, scaffold and plumbing plan/drawing
Learning Activity 2.3.1
Learning Activity Resources/Special Instructions/References
Collecting and checking tools, equipment
and materials
▪ Information Sheet: 2.3.1, 2.3.2, 2.3.3, 2.3.4 ▪ Self-Check Quiz: 2.3.1 ▪ Answer Key: 2.3.1
Information Sheet 2.3.1
Learning Objective: to identify and uses of personal protective equipment in the workplace.
Personal Protective Equipment (PPE):
Same as Information Sheet 1.1.1 – Gather and check tools, equipment and materials (page 8-9)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 42
Skills for Employment Investment Programme (SEIP)
Information Sheet 2.3.2
Learning Objective: to identify, uses and check of tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.2 – Gather and check tools, equipment and materials operation (page
10 - 12)
Information Sheet 2.3.3
Learning Objective: to identify, uses and check of tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.3 – Gather and check tools, equipment and materials (page 13 - 14)
Information Sheet 2.3.4
Learning Objective: to identify, uses and check of tools, equipment and materials in plumbing works.
Materials and pipes:
1
Teflon tape is used to seal the thread of pipes
2
Hemp is a fibre that it is the traditional method of aiding the
sealing of heavier gauge pipe work. It must be used in
conjunction with a suitable paste sealant
3
PVC Solvent Cement and Primer is used to glue cpvc/pvc
joints
4
Poly Propylene Random (PPR) Pipe used for transfer hot
and cold water
5
PVC (polyvinyl chloride) is a common, strong but
lightweight plastic used in construction
CBLM – Plumbing (Student Guide) v.1 Oct 2018 43
Skills for Employment Investment Programme (SEIP)
6
uPVC pipe: If no plasticizers are added, it is known as
uPVC (un-plasticized polyvinyl chloride), rigid PVC.
7
GI (Galvanised Iron) pipes: Transfers water in various
plumbing applications
8
MS (Mild Steel) pipes: Transfers gas / water in various
plumbing applications
9
SS (Stainless Steel) pipes: These are also heavy duty
and costly pipes used to transfers gas / water in various
plumbing applications.
10
CI (Cast Iron) pipes: These are most suitable and used
for rain water disposal and waste water disposal etc.
11
Copper pipes: These pipes are used for industrial
purposes for heavy flows.
12
Concrete pipes: For heavy drainage water disposal,
concrete pipes of large diameters are used. Smaller
diameter pipes are used for small flows.
13
Asbestos Cement Pipes: These pipes are used as vent
pipes, soil pipes and rain water pipes. They are very
cheap compared to all but they can break easily.
14
High Density Polyethylene (HDP) pipes: This pipe is
used for water supply, waste water disposal and as
electrical conduit.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 44
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 2.3.1
Check your understanding by answering the following questions:
1. Why Teflon tape is used in plumbing works?
2. What is Hemp?
3. Write the full name of PPR pipe.
4. Write the full name of PVC pipe.
5. Write the full name of GI pipe.
6. Write the full name of CI pipe.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 45
Skills for Employment Investment Programme (SEIP)
Learning Outcome 2.4 - Cut and Make Access Through Walls and Floors
Contents:
▪ Lay out for access/encroachment work ▪ Techniques of cutting walls and floors
Assessment criteria:
1. Lay out for access/encroachment work is made. 2. Concrete wall and floor are cut to create pipe access/encroachment in accordance to plumbing
plan/specification.
3. Cutting walls and floors are made without causing damage to the wall or floor and adjacent installations.
4. Appropriate tools and equipment are used.
Resources required:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, hacksaw, cold chisel, hammer ▪ Equipment: power hacksaw, electric drill machine ▪ Materials: soft stone (marker), marking pen, pencil, masking tape and plumbing plan/drawing
Learning Activity 2.4.1
Learning Activity Resources/Special Instructions/References
Cut and make access through
walls and floors
▪ Information Sheet: 2.4.1 ▪ https://www.bhg.com/home-improvement/plumbing/how-to-run-
pipes-throug
Information Sheet 2.4.1
Learning Objective: to cut and make access through walls and floors for plumbing fixtures installation.
Lay out: In plumbing system lay out helps in many ways to cut and make access through walls and floors for plumbing fixtures installation in a desired location.
How to cut and make access through walls and floors? ▪ Collect and study the building drawing and plumbing design/drawing ▪ Prepare a layout for access/encroachment work ▪ Make a list of tools, equipment and materials to carry out the works ▪ Collect the appropriate tools, equipment and materials
CBLM – Plumbing (Student Guide) v.1 Oct 2018 46
Skills for Employment Investment Programme (SEIP)
▪ Use appropriate tools and equipment to cut the walls and floors ▪ Take special care during cutting the walls and floors to avoid damage to the wall or floor and
adjacent installations ▪ Cut the walls and floors to create pipe access/encroachment in accordance to plumbing
plan/specification ▪ Repair the cutting spots after completion of piping works ▪ Clean the tools and equipment ▪ Dispose excess and waste materials.
Do you know?
▪ Right layout for access or encroachment works can help to avoid damage of other installations?
▪ Use of inappropriate tools and equipment may cause serious accident in the workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 47
Skills for Employment Investment Programme (SEIP)
Learning Outcome 2.5 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 48
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 2.1.1
1. Line of encroachment in plumbing works are floors, walls, ceilings, slabs, beams, columns etc.
Answer Key 2.3.1
1. Eye protector/goggles/safety glasses
2. Safety vest
3. Hand gloves
4. Safety shoes/footwear/boots
5. Safety belt
CBLM – Plumbing (Student Guide) v.1 Oct 2018 49
Skills for Employment Investment Programme (SEIP)
Module 3: Carry out water supply line installation using G.I, PPR and HDP pipes
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to carry out water
supply line installation using G.I pipe, PPR and HDP pipes which includes
gathering and inspecting tools, equipment and materials, performing pipe
cutting operation, pipe threading operation, assembling pipe runs, and
cleaning/maintaining the work area. It also includes information sheets, activity
sheets, job sheets, self-check quizzes and answer keys.
Nominal Duration: 50 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
3.1 Gather and inspect tools, equipment and materials
3.2 Perform pipe cutting operation
3.3 Perform pipe threading operation
3.4 Assemble pipe runs
3.5 Clean/maintain the work area
Performance Criteria:
1. Personal protective equipment (PPE) is selected and used.
2. Tools, equipment and materials are gathered and checked for usability.
3. Pipes are identified and gathered in accordance with plumbing plan and specifications.
4. Pipes are measured and marked as per plan/drawing specification.
5. Pipes are clamped and fixed using appropriate clamping device.
6. Pipes are cut using appropriate cutting tool.
7. Pipes are cut within the specified dimension and considering specified tolerance.
8. Diestocks are adjusted and initiated into the pipe end squarely.
9. Thread cutting is carried out on pipes in accordance to workplace procedure.
10. Coolant is used during thread cutting operation.
11. Threads are checked to conform with the specified form and measurement in accordance with plan/drawing
12. Pipe runs is positioned on the corresponding areas as per plumbing plan.
13. Piping joints and fittings are tightened using appropriate tools and sealant.
14. Pipe clamps and fixtures along pipe runs are installed in accordance with plumbing plan.
15. Leaks and non-conformance to plumbing design/plans are checked and corrected.
16. Holes and openings are filled with cement plasters and finishing.
17. Plumbing tools/equipment is cleaned and maintained.
18. Work area is cleaned and waste materials are disposed of in accordance with workplace requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 50
Skills for Employment Investment Programme (SEIP)
Learning Outcome 3.1 - Gather and Inspect Tools, Equipment and Materials
Contents:
▪ Name of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug
▪ List of main tools, equipment and materials uses ▪ Different kinds of pipes with uses: galvanized iron (GI), polypropylene (PPR) and high-density
polyethylene (HDP) pipe
Assessment criteria:
1. Personal protective equipment (PPE) is selected and used. 2. Tools, equipment and materials are gathered and checked for usability. 3. Pipes are identified and gathered in accordance with plumbing plan and specifications.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, sealant (plastic, rubber,
synthetic) thread tape (Teflon), welding rod, masking tape ▪ Pipe: GI, PPR and HDP pipes (different diameter) ▪ Fittings: gate valve, check valve, globe valve and foot valve
Learning Activity 3.1.1
Learning Activity Resources/Special Instructions/References
Gather and check tools, equipment
and materials
▪ Information Sheets: 3.1.1, 3.1.2, 3.1.3, 3.1.4, 3.1.5, 3.1.6 ▪ Self-Check Quiz: 3.1.1, 3.1.2 ▪ Answer Key: 3.1.1, 3.1.2
CBLM – Plumbing (Student Guide) v.1 Oct 2018 51
Skills for Employment Investment Programme (SEIP)
Information Sheet 3.1.1
Learning Objective: to identify and uses of the personal protective equipment in the workplace.
Personal Protective Equipment (PPE): Same as Information Sheet 1.1.1 – Gather and check tools, equipment and materials (page 8 - 9)
Information Sheet 3.1.2
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.2 – Gather and check tools, equipment and materials (page 10 - 12)
Information Sheet 3.1.3
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.3 – Gather and check tools, equipment and materials (page 13 - 14)
Information Sheet 3.1.4
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Materials:
Same as Information Sheet 1.1.4 – Gather and check tools, equipment and materials (page 14 - 15)
Information Sheet 3.1.5
Learning Objective: to identify and uses of different types of plumbing fittings in the workplace.
Fittings: are used in pipe systems to connect straight pipe or tubing sections, adapt to different sizes or shapes and for other purposes.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 52
Skills for Employment Investment Programme (SEIP)
Elbow:
Elbow is used to join two lengths of pipe (equal or un-
equal diameter).
Bend:
Bend is used to join two lengths of pipe (equal or un-
equal diameter).
Tee (T):
Tee is used to connect three lengths of pipe (equal or
un-equal diameter) comes in a number of sizes, it also
used to connect a reduced branch line.
Union:
Union is used to connect two pipe lengths together
comes in a number of sizes. It is used where a pipe line
is opened to replace a damaged section or to cut into an
existing line.
Reducer:
Reducer is used to join two different size pipes in a
straight way.
Socket:
Socket is used to connect two pipe lengths together
comes in a number of sizes.
Nipple:
A nipple is used between two fittings.
Bush:
A bush is used to connect the male end of a pipe to a
fitting of larger or smaller diameter pipe.
Adapter (male/female):
An adapter is used to connect the threaded end of a pipe
to a fitting.
Plug:
Plug is used to seal off a GI fitting.
Cap:
Cap is used to seal off pipe end.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 53
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 3.1.1
Read the following statements and write/mark true or false accordingly:
No. Description True False
1. Elbow is used to join three lengths of pipe (equal or un-equal diameter)
2. Tee is used to connect two lengths of pipe (equal or un-equal diameter)
comes in a number of sizes
3. Union is used, where a pipe line is opened to replace a damaged section or
to cut into an existing line
4. Reducer is used to join two different size pipes in a straight way
5. Socket is used to connect three pipe lengths together comes in a number of
sizes
6. A nipple is used between two fittings
7. A bush is used to connect the male end of a pipe to a fitting of larger or
smaller diameter pipe
8. An adapter is used to connect the threaded end of a pipe to a fitting
9. Cap is used to seal off a GI fitting
10. Plug is used to seal off pipe end
Information Sheet 3.1.6
Learning Objective: to identify and uses of different types of valves in the workplace.
Valves: in a plumbing system valves are used to start or stop liquid, steam or gas flow.
Stopcock:
Stopcock is used to shut off the flow of water in
a pipe
Gate valve:
Gate valve is used to start or stop liquid, steam
or gas flow.
Butterfly valve:
A butterfly valve is a valve that isolates or
regulates the flow of a fluid.
Ball valve:
This is a valve with a spherical disc, the part of
the valve which controls the flow through it.
Check valve:
This type of valve allows to flow only in one
direction.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 54
Skills for Employment Investment Programme (SEIP)
Globe valve:
Globe valves are mainly supply to stop or
connect the medium in the pipelines.
Non-return valve:
Non-return valves are used to allow the flow
only in one direction.
Float valve:
A float valve is used inside the flashing tank to
fill and control water in tank.
Foot valve:
Foot valves are always fitted with filters or
strainers.
Pressure reducing valve:
It is installed to maintain a pre-set (desired)
constant pressure in the downstream of the
valve.
Pressure relief valve:
In a water supply system pressure relief valve
is used to prevent or to relieve excessive high
pressure in piping or in any appliances.
Safety Valve:
This is a safety device which automatically
controls the pressure and discharges certain
amount of fluid by itself without any electric
power support.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 55
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 3.1.2
Check your understanding by answering the following questions:
No. Identify the valves given below Name of the valve
1
2
3
4
5
6
7
8
CBLM – Plumbing (Student Guide) v.1 Oct 2018 56
Skills for Employment Investment Programme (SEIP)
Learning Outcome 3.2 - Perform Pipe Cutting Operation
Contents:
▪ GI, PPR and HDP pipes and their uses ▪ Clamping device (pipe stand, bench vice (w/v blocks), vice grip, pipe chuck, threading machine chucks) ▪ Cutting tools ▪ Tolerance
Assessment criteria:
1. G.I/PPR/HDP pipes are measured and marked as per plan/drawing specification. 2. G.I/PPR/HDP pipes are clamped using appropriate clamping device.
3. G.I/PPR/HDP pipes are cut using appropriate cutting tool.
4. G.I/PPR/HDP pipes are cut within the specified dimension and considering specified tolerance.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, sealant (plastic, rubber,
synthetic) thread tape (Teflon), welding rod, masking tape ▪ Pipe: GI, PPR and HDP pipes (different diameter)
Learning Activity 3.2.1
Learning Activity Resources/Special Instructions/References
Perform pipe cutting operation ▪ Information Sheets: 3.2.1, 3.2.2 ▪ Self-Check Quiz: 3.2.1 ▪ Answer Key: 3.2.1 ▪ https://www.youtube.com/watch?v=RMvw5m1nNx4
Information Sheet 3.2.1
Learning Objective: to identify and uses of different types of pipes in a workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 57
Skills for Employment Investment Programme (SEIP)
Pipes:
Same as Information Sheet 2.3.4 – Gather Tools, Equipment and Materials (page 42 - 43)
Information Sheet 3.2.2
Learning Objective: to identify and uses of measuring tools, marking tools, clamping device and cutting
tools in a workplace.
Measuring, Marking, Clamping and Cutting tools/devices:
Measuring Tape:
Used to measure different lengths of pipes
Steel rule:
Used to measure pipe diameter etc.
Marker pen:
Marking out on the material a required
measurement
Pipe vice:
A pipe vice is a plumbing tool used to hold pipe or
tube securely so that it can be cut or threaded.
Tripod Chain Pipe Vice
Portable Vice to clamp pipe when threading or
cutting
Single Stroke Chain Pipe Cutter:
To cut steel and cast-iron water and soil pipes
Ratchet Type Chain Pipe Cutter:
To cut steel and cast-iron water and soil pipes
Hacksaw:
Cutting GI pipe and metal material
Three Wheel Type Pipe Cutter:
The three-wheel type pipe cutter has two high
speed steel wheels positioned in the body of the
cutter and one high speed wheel position in the
adjustable slide
Roller Pattern Pipe Cutter:
The roller pattern cutter has one high speed
wheel positioned in the body and two rollers
positioned in the adjustable slide.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 58
Skills for Employment Investment Programme (SEIP)
PPR pipe cutter:
The PPR pipe cutter is used to cut PPR pipe.
Tolerance:
In Engineering, tolerance is the permissible limit
or limits of variation in a physical dimension.
To cut pipes the following activities need to be done:
1. Select tools, materials and drawing 2. Use appropriate personal protective equipment (PPE) 3. Place pipe vice on the ground 4. Mark the cutting point of the pipe as per measurement using marker pen 5. Fix the pipe firmly with the grip of pipe vice 6. Cut the pipe using pipe cutter or hack saw or hand saw depending on the types of pipe 7. Remove pipe from the pipe vice 8. Clean the work place 9. Restore all tools and materials
Self-Check Quiz 3.2.1
Check your understanding by answering the following questions:
Match the pictures shown in column A to the names in column B:
No Column A No Column B
1
i Steel rule
2
ii Measuring Tape
3
iii PPR pipe cutter
4
iv Tripod Chain Pipe Vice
CBLM – Plumbing (Student Guide) v.1 Oct 2018 59
Skills for Employment Investment Programme (SEIP)
5
v Pipe vice
6
vi Ratchet Type Chain Pipe Cutter
7
vii Single Stroke Chain Pipe Cutter
8
viii Roller Pattern Pipe Cutter
9
ix Three Wheel Type Pipe Cutter
10
x Marker pen
CBLM – Plumbing (Student Guide) v.1 Oct 2018 60
Skills for Employment Investment Programme (SEIP)
JOB SHEET 3
Qualification: Plumbing
Learning unit: Perform pipe cutting operation:
Cut G I/PPR/HDP pipes
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: G I / PPR / HDP pipes, lubricant
Tools and equipment: Measuring tape, foot rule, hack saw, back saw, marker pen, pipe cutter, pipe vice, 3-wheel type pipe cutter
Performance Criteria 1. Cut the GI / PPR/HDP pipe with a hacksaw / pipe cutter 2. Measurement error must be within approximately 2mm 3. Pipes must be cut uniformly one end to another end.
Measurement: ▪ Cut GI pipe as per drawing using hacksaw and 3-wheel type cutters.
▪ Cut PPR pipe as per drawing using hacksaw.
▪ Cut HDP pipe as per drawing using hacksaw.
Procedure: 1. Identify the type pipe required.
2. Measure, cut using a hacksaw as per measurement on drawing 2 x 450 mm lengths of 20mm ɸ GI pipe.
3. Measure, cut using a 3-wheel type pipe cutter 1 x 250mm length 20mm ɸ PPR pipe.
4. 1 x 450 mm lengths of 20mm ɸ PPR pipe. 5. Measure, cut using a hacksaw 1 x 250mm length 20mm ɸ HDP pipe. 6. 1 x 450 mm lengths of 20mm ɸ HDP pipe. All pipes must be cut uniformly
one end to another end. 7. Measurement error must be within approx. 2mm
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 61
Skills for Employment Investment Programme (SEIP)
Individual Activity:
▪ Watch the video on ‘How to cut water supply pipes’ and summarise the key points (if facilities available)
▪ Cut the pipes following the Job Sheet 3 (see above)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 62
Skills for Employment Investment Programme (SEIP)
Learning Outcome 3.3 - Perform Pipe Threading Operation
Contents:
▪ GI, PPR and HDP pipes clamping procedure. ▪ Diestocks adjustment technique ▪ Thread cutting procedure ▪ Coolant: water, oil, air, synthetic, nitrogen ▪ Threads checking
Assessment criteria:
1. GI, PPR and HDP pipes are clamped and fixed using appropriate clamping device.
2. Diestocks are adjusted and initiated into the pipe end squarely.
3. Thread cutting is carried out on pipes in accordance to workplace procedure.
4. Coolant is used during thread cutting operation.
5. Threads are checked to conform with the specified form and measurement in accordance with
plan/drawing.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, sealant (plastic, rubber,
synthetic) thread tape (Teflon), welding rod, masking tape ▪ Pipe: GI, PPR and HDP pipes (different diameter)
Learning Activity 3.3.1
Learning Activity Resources/Special Instructions/References
Perform pipe threading
operation
▪ Information Sheet: 3.3.1 ▪ https://www.wikihow.com/Thread-Pipe
CBLM – Plumbing (Student Guide) v.1 Oct 2018 63
Skills for Employment Investment Programme (SEIP)
Information Sheet 3.3.1
Learning Objective: to identify and uses of pipe vice, de burring tool, diestocks and coolant in the
workplace.
Pipe threading activities (pictorial representation):
A. PREPARE PIPE FOR THREADING
1. Place pipe to be treaded into the pipe vice and tighten
2. In order for the pipe die stock to get a grip it is important to taper the pipe edge. This can be achieved by either filing the bevel to the edge or by using a grindstone.
B. REMOVE BURRS
3. Remove all burrs on the interior of pipe using a round file to file off any burrs.
4. Push the reamer into the pipe, turn the
reamer clockwise in short even strokes until the inside burrs are removed
5. Remove the outside burrs with a file if a
three-wheel cutter is used
C. CUT EXTERNAL THREAD
6. Prior to cutting the thread place some lubricant to proposed cut area
7. Place the correct size pipe guide and die into the diestock.
• Thread per inch (TPI) must be 14 for ½” and ¾” diameter pipes and 11 for 1-inch diameter pipes.
8. Apply uniform pressure and turn the die stock clockwise, proceed for about four to five turns
9. After five turns clockwise start to rotate the
die stock in an anticlockwise direction
CBLM – Plumbing (Student Guide) v.1 Oct 2018 64
Skills for Employment Investment Programme (SEIP)
10. During the treading clear out the cuttings from the die or blow them out with compressed air.
11. Proceed to cut the thread until one or two
threads are visible
12. Remove the die set from the pipe checking
the cut area for any broken threads
SPECIFICATION SHEET 1
Thread Length Data:
Same as Information Sheet 1.3.1 – Gather and check tools, equipment and materials (page 13 - 14)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 65
Skills for Employment Investment Programme (SEIP)
Learning Outcome 3.4 - Assemble Pipe Run
Contents:
▪ Piping joints and fittings tightening: techniques and safety precautions ▪ Sealants: thread tape (Teflon), cement, seals (plastic, rubber, synthetic & silicone) ▪ Pipe clamps and fixtures: steel pipe hanger, plastic pipe hanger, pipe clamps (plastic, steel and rubber)
and tapes ▪ Leak and non-conformance: leak, length (dimension), pipe size, pipe offset angles, obstacles and
aesthetics/appearance ▪ Finishing: caulk, cement, paint, tiles/marble and grommet
Assessment criteria:
1. G.I/PPR/HDP pipe run is positioned on the corresponding areas as per plumbing plan. 2. Piping joints and fittings are tightened using appropriate tools and sealant.
3. Pipe clamps and fixtures along pipe run is installed in accordance with plumbing plan.
4. Leaks and non-conformance to plumbing design/plans are checked and corrected.
5. Holes and openings are filled with cement plasters and finishing.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape, cement, sand and plumbing plan/drawing ▪ Pipe: GI, PPR and HDP pipes (different diameter)
Learning Activity 3.4.1
Learning Activity Resources/Special Instructions/References
Assemble pipe run ▪ Information Sheet: 3.4.1 ▪ https://knowledge.autodesk.com/support/inventor-
products/learn-explore/
CBLM – Plumbing (Student Guide) v.1 Oct 2018 66
Skills for Employment Investment Programme (SEIP)
Information Sheet 3.4.1
Learning Objective:
▪ List out the tools, equipment and materials required for making pipe joints ▪ Explain the necessity of assemble pipe run ▪ Describe the procedure of assemble pipe run
On completion of this task you will be able to complete the following steps:
1. Collect tools, equipment and materials. 2. Cut the pipe as per required measurement with pipe cutter or hacksaw. 3. Lay down the pipes in accordance with the planned/designed pipe run.
4. Assembled and fixed the pipes and pipe fittings in accordance with planned/designed pipe run.
5. Temporarily join pipes and fittings and make sure that the pipe in the run is facing the right direction.
6. Use a felt-tip pen to make alignment marks on all the joints where the fitting must face correctly.
7. Disassemble, keeping careful track of the order of installation.
8. Apply primer to each pipe end and each fitting.
9. Apply solvent/cement and join each pipe in order.
10. Checked the pipes, fittings and pipe runs for damage/quality of work.
11. Assembled pipe runs are measured/checked within tolerable dimensions/length in accordance with
design/specification
12. Conduct leakage test using water 13. Clean the workplace 14. Restore the tools equipment and materials.
GI Pipe Joints
PPR Pipe Joints
Sealant: is a substance used to block the passage of fluids through the surface or joints or openings in materials. It may be weak or strong, flexible or rigid, permanent or temporary. These are not adhesives but some have adhesive qualities and are called adhesive-sealants or structural sealants. The followings may include as sealant in plumbing works: ▪ Thread tape (Teflon) ▪ Cement ▪ Plastic based seals ▪ Rubber based seals ▪ Synthetic seals ▪ Silicon seals
CBLM – Plumbing (Student Guide) v.1 Oct 2018 67
Skills for Employment Investment Programme (SEIP)
Different types of Pipe clamps and fixtures:
In plumbing system steel, rubber and plastic made pipe clamps, fixtures and hangers are used.
Pipe strap
Pipe clip
Split ring hanger
Cushion clamp
Split ring hanger
Single hole wrap strap
Channel nut
Swivel loop hanger
J-hook hanger
Rowel plug
Screw
Concrete drilling
Non-conformance: ▪ Leak ▪ Length (dimension) ▪ Pipe size ▪ Pipe offset angles ▪ Obstacles ▪ Aesthetics/appearance.
Finishing materials: ▪ Caulk ▪ Cement ▪ Enamel Paint ▪ Tiles/marble ▪ Grommet
Pipe Insulation: is thermal or acoustic insulation used on pipework. Some methods of application for pipe insulation are as follows:
▪ Condensation control:
▪ Pipe freezing:
▪ Energy saving:
▪ Protection against extreme temperatures:
▪ Control of noise:
Individual Activity:
▪ Watch the videos on ‘How to bend PVC’ and summarise key points ▪ Watch the videos on ‘How to PPR’ and summarise key points (if facilities available)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 68
Skills for Employment Investment Programme (SEIP)
Learning Outcome 3.5 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 69
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 3.1.1
1. False 2. False 3. True 4. True 5. False 6. True 7. True 8. True 9. False 10. False
Answer Key 3.1.2
1. Stop cock 2. Gate valve 3. Butterfly valve 4. Ball valve 5. Check valve 6. Globe valve 7. Float valve 8. Foot valve
Answer Key 3.2.1
No. Name the Tools
1 ii
2 i
3 x
4 v
5 iv
6 vii
7 vi
8 ix
9 viii
10 iii
CBLM – Plumbing (Student Guide) v.1 Oct 2018 70
Skills for Employment Investment Programme (SEIP)
Module 4: Carry out water supply line installation using PVC/UPVC pipes
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to carry out water
supply line installation using PVC/UPVC pipes which includes gathering and
inspecting of tools, equipment and materials, performing PVC/UPVC pipe
cutting operation, performing PVC/UPVC pipe run assembly, and
cleaning/maintaining the work area. It also includes information sheets, activity
sheets, job sheets, self-check quizzes and answer keys.
Nominal Duration: 44 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
4.1 Gather and inspect tools, equipment and materials
4.2 Perform PVC/UPVC pipe cutting operation
4.3 Perform PVC/UPVC pipe run assembly
4.4 Clean/maintain the work area
Performance Criteria:
1. Personal protective equipment (PPE) is selected and used.
2. Tools, equipment and materials are gathered and checked for usability.
3. PVC/UPVC pipes sizes and schedules are identified and gathered.
4. PVC/UPVC pipes are measured and marked as per plan/drawing specification.
5. PVC/UPVC pipes are clamped using appropriate clamping device.
6. PVC/UPVC pipes are cut using appropriate cutting tool.
7. PVC/UPVC pipes are cut within the specified dimension and considering specified tolerance.
8. PVC/UPVC pipe runs is positioned on the corresponding location as per plumbing plan.
9. PVC/UPVC piping joints and fittings are assembled using appropriate tools and sealant.
10. Pipe clamps and fixtures along pipe runs are installed in accordance with plumbing plan.
11. Leaks and non-conformance to plumbing design/plans are checked and corrected.
12. Holes and openings are filled with cement plasters and finishing.
13. Plumbing tools/equipment is cleaned and maintained.
14. Work area is cleaned and waste materials are disposed of in accordance with workplace
requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 71
Skills for Employment Investment Programme (SEIP)
Learning Outcome 4.1 - Gather and Inspect Tools, Equipment and Materials
Contents:
▪ Names of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug
▪ List of main tools, equipment and materials uses ▪ Different sizes of PVC/UPVC pipes with uses
Assessment criteria:
1. Personal protective equipment (PPE) is selected and used. 2. Tools, equipment and materials are gathered and checked for usability. 3. PVC/UPVC pipes sizes and schedules are identified and gathered.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, sealant (plastic, rubber,
synthetic) thread tape (Teflon), welding rod, masking tape ▪ Pipe: PVC/UPVC pipes (different diameter)
Learning Activity 4.1.1
Learning Activity Resources/Special Instructions/References
Gather and check tools,
equipment and materials
▪ Information Sheets: 4.1.1, 4.1.2, 4.1.3, 4.1.4, 4.1.5, 4.1.6 ▪ Self-Check Quiz: 4.1.1 ▪ Answer Key: 4.1.1 ▪ https://www.plumbingsupply.com/tools.html ▪ https://www.homedepot.com/b/Plumbing-Plumbing-Tools/N-
5yc1vZbqlq
Information Sheet 4.1.1
Learning Objective: to identify and uses of the personal protective equipment in the workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 72
Skills for Employment Investment Programme (SEIP)
Personal Protective Equipment (PPE): Same as Learning Outcome 1.1.1 – Gather and check tools, equipment and materials (page 8 - 9)
Information Sheet 4.1.2
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.2 – Gather and check tools, equipment and materials (page 10 - 12)
Information Sheet 4.1.3
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.3 – Gather and check tools, equipment and materials (page 13- 14)
Information Sheet 4.1.4
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.4 – Gather and check tools, equipment and materials (page 14 - 15)
Same as Information sheet: 1.1.4 of module-1: Performing pipe threading operation
Information Sheet 4.1.5
Learning Objective: to identify and uses of different types of plumbing fittings in the workplace.
Fittings: are used in pipe systems to connect straight pipes, adapt to different sizes or shapes and for other purposes.
Elbow:
Elbow is used to join two lengths of pipe (equal or
un-equal diameter).
CBLM – Plumbing (Student Guide) v.1 Oct 2018 73
Skills for Employment Investment Programme (SEIP)
Bend:
Bend is used to join two lengths of pipe (equal or
un-equal diameter).
Tee (T):
Tee is used to connect three lengths of pipe
(equal or un-equal diameter) comes in a number
of sizes, it also used to connect a reduced branch
line.
Union:
Union is used to connect two pipe lengths
together comes in a number of sizes. It is used
where a pipe line is opened to replace a damaged
section or to cut into an existing line.
Reducer:
Reducer is used to join two different size pipes in
a straight way.
Socket:
Socket is used to connect two pipe lengths
together comes in a number of sizes.
Nipple:
A nipple is used between two fittings.
Bush:
A bush is used to connect the male end of a pipe
to a fitting of larger or smaller diameter pipe.
Adapter (male/female):
An adapter is used to connect the threaded end
of a pipe to a fitting.
Plug:
Plug is used to seal off a pipe fitting.
Cap:
Cap is used to seal off pipe end.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 74
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 4.1.1
Check your understanding by answering the following questions:
Read the following statements and write/mark true or false accordingly:
No. Description True False
1. Elbow is used to join three lengths of pipe (equal or un-equal diameter)
2. Tee is used to connect two lengths of pipe (equal or un-equal diameter)
comes in a number of sizes
3. Union is used, where a pipe line is opened to replace a damaged section or
to cut into an existing line
4. Reducer is used to join two different size pipes in a straight way
5. Socket is used to connect three pipe lengths together comes in a number of
sizes
6. A nipple is used between two fittings
7. A bush is used to connect the male end of a pipe to a fitting of larger or
smaller diameter pipe
8. An adapter is used to connect the threaded end of a pipe to a fitting
9. Cap is used to seal off a pipe fitting
10. Plug is used to seal off pipe end
Information Sheet 4.1.6
Learning Objective: to identify and uses of different types of valves in a workplace.
Valves:
Same as Information Sheet 3.1.6 – Gather and Inspect Tools, Equipment and Materials (page 54 - 55)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 75
Skills for Employment Investment Programme (SEIP)
Learning Outcome 4.2 - Perform PVC/UPVC Pipe Cutting Operation
Contents:
▪ PVC/UPVC pipes and uses ▪ Clamping device ▪ Cutting tools ▪ Tolerance
Assessment criteria:
1. PVC/UPVC pipes are measured and marked as per plan/drawing specification. 2. PVC/UPVC pipes are clamped using appropriate clamping device.
3. PVC/UPVC pipes are cut using appropriate cutting tool.
4. PVC/UPVC pipes are cut within the specified dimension and considering specified tolerance.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), masking tape and plumbing plan/drawing ▪ Pipe: PVC/UPVC pipes (different diameter)
Learning Activity 4.2.1
Learning Activity Resources/Special Instructions/References
Perform PVC/UPVC pipe cutting operation ▪ Information Sheets: 4.2.1, 4.2.2 ▪ Job Sheet 4 ▪ Self-Check Quiz: 4.2.1
▪ Answer Key: 4.2.1
▪ https://www.youtube.com/watch?v=_D8wtNYeX40
▪ https://www.instructables.com/id/Tips-on-Cutting-
PVC-Pipe/
CBLM – Plumbing (Student Guide) v.1 Oct 2018 76
Skills for Employment Investment Programme (SEIP)
Information Sheet 4.2.1
Learning Objective: to identify and uses of different types of pipes in the workplace.
Pipes: Same as Information Sheet 2.3.4 – Gather Tools, Equipment and Materials (page 42 - 43)
Information Sheet 4.2.2
Learning Objective: to identify and uses of measuring tools, marking tools, clamping device and cutting
tools in the workplace.
Measuring, Marking, Clamping and Cutting tools/devices:
Same as Information Sheet 3.2.2 – Perform Pipe Cutting Operation (page 58 - 59)
Tolerance:
Same as Information Sheet 3.2.2 – Perform Pipe Cutting Operation (page 58 - 59)
To cut pipes the following activities to be done: 1. Collect tools, materials and drawing. 2. Use appropriate personal protective equipment (PPE). 3. Place pipe vice on the ground. 4. Mark the cutting point of the pipe as per measurement using marker pen. 5. Fix the pipe firmly with the grip of pipe vice. 6. Cut the pipe using pipe cutter or hack saw or hand saw depending on the types of pipe. 7. Remove pipe from the pipe vice. 8. Clean the work place. 9. Restore all tools and materials.
Pipe cutting activities (pictorial representation):
To measure the cutting length of the PVC / uPVC pipes
take the length that you will require to cut, minus the
length of the fitting and add the length that the pipe will
thread or join into the fitting.
This will give you the correct cut length. Mark this on the
different pipes to be cut.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 77
Skills for Employment Investment Programme (SEIP)
Transfer the mark around the circumferance of the
different pipes
Start cut by carefully placing the hacksaw blade on the
mark and drawing back. Pressure should be applied on
the forward stroke and released on the backward stroke
and strokes should be slow and even
Cut with a backsaw. When top of backsaw
touches the "top" of the pipe, turn it over to finish cutting.
Using the scissor type pipe cutter squeeze the handles
together to cut the pipe.
To cut PVC pipe place the pipe cutter and secure in
position of the marked measurement turn and tighten
every couple of turns until the pipe is eventually cut
through.
Self-Check Quiz 4.2.1
Check your understanding by answering the following questions:
No. Description Name of the tool
1
2
3
4
CBLM – Plumbing (Student Guide) v.1 Oct 2018 78
Skills for Employment Investment Programme (SEIP)
5
6
7
8
9
10
CBLM – Plumbing (Student Guide) v.1 Oct 2018 79
Skills for Employment Investment Programme (SEIP)
JOB SHEET 4
Qualification: Plumbing
Learning unit: Perform PVC/UPVC pipe cutting operation
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: PVC / UPVC pipes
Tools and equipment: Measuring tape, foot rule, hack saw, back saw, marker pen, pipe cutter, tube vice
Performance Criteria 1. Cut the PVC / UPVC pipe with a hacksaw / pipe cutter 2. Measurement error must be within approximately 2mm 3. Pipes must be cut uniformly one end to another end.
Measurement: Cut PVC / UPVC pipe as per drawing using hacksaw or pipe cutter.
Procedure: 1. Identify the type pipe required.
2. Measure, cut using a 3-wheel type pipe cutter 1 x 250mm length 20mm ɸ PVC/UPVC pipe.
3. 1 x 450 mm lengths of 20mm ɸ PVC/UPVC pipe. 4. Measure, cut using a hacksaw 1 x 250mm length 20mm ɸ PVC/UPVC
pipe. 5. 1 x 450 mm lengths of 20mm ɸ PVC/UPVC pipe. All pipes must be cut
uniformly one end to another end. 6. Measurement error must be within approx. 2mm
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 80
Skills for Employment Investment Programme (SEIP)
Individual Activity:
▪ Watch the video on ‘How to cut water supply pipes’ and summarise the key points (if facilities available).
▪ Cut the pipes following the standard method and Job Sheet 4 (see above)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 81
Skills for Employment Investment Programme (SEIP)
Learning Outcome 4.3 - Perform PVC/UPVC Pipe Run Assembly
Contents:
▪ Piping joints and fittings tightening: techniques and safety precautions ▪ Sealants: thread tape (Teflon), cement, seals (plastic, rubber, synthetic & silicone) ▪ Pipe clamps and fixtures: steel pipe hanger, plastic pipe hanger, pipe clamps (plastic, steel and rubber)
and tapes ▪ Leak and non-conformance: leak, length (dimension), pipe size, pipe offset angles, obstacles and
aesthetics/appearance ▪ Finishing: caulk, cement, paint, tiles/marble and grommet
Assessment criteria:
1. PVC/UPVC pipe runs is positioned on the corresponding location as per plumbing plan. 2. PVC/UPVC piping joints and fittings are assembled using appropriate tools and sealant.
3. Appropriate curing time for sealant is done to create strong bond.
4. Pipe clamps and fixtures along pipe runs are installed in accordance with plumbing plan.
5. Leaks and non-conformance to plumbing design/plans are checked and corrected.
6. Holes and openings are filled with cement plasters and finishing.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), masking tape and plumbing plan/drawing ▪ Pipe: PVC/UPVC pipes (different diameter)
Learning Activity 4.3.1
Learning Activity Resources/Special Instructions/References
Perform PVC/UPVC pipe run
assembly ▪ Information Sheet: 4.3.1 ▪ http://www.iitk.ac.in/ce/test/IS-codes/is.13593.1992.pdf
CBLM – Plumbing (Student Guide) v.1 Oct 2018 82
Skills for Employment Investment Programme (SEIP)
Information Sheet 4.3.1
Learning Objective: list the tools, equipment and materials required for making pipe joints, explain the
necessity of assemble pipe run, and describe the procedure of assemble pipe run.
PVC/UPVC Pipe Joints activities (pictorial representation)
A. Bell Joint in PVC/UPVC Pipes using the Traditional Method:
1. To form a bell in a UPVC pipe the traditional method is being used in Bangladesh that is to heat the pipe on an open fire.
2. The pipe is held over the heat on the outside to start the softening the area to form the bell in the pipe
3. The pipe is held over the heat at angle so as to enable the heat to be transferred to the inside of the pipe, to start the softening the area to form the bell in the pipe
4. Once the pipe has become softened in the area required for the bell bring the other pipe closer ready to form the bell before the heat is lost.
5. Taking the other pipe insert the pipe’s end into the softened section of the heated pipe, thereby expanding the pipe to bell out to the required depth.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 83
Skills for Employment Investment Programme (SEIP)
6. Remove the pipe and allow the heated pipe to harden and retain the bell shape required.
B. Bell Joint in PVC/UPVC Pipes using the Heat Gun:
1. Take the heat gun and after setting the temperature on high position the gun transfers the heat over the mouth of the pipe
2. Transfer the heat gun to inside area of the pipe and allow the pipe to soften in the area of the proposed bell joint.
3. Remove the heat gun from the inside to concentrate on the surrounding exterior of the proposed area of the bell joint
4. Insert the Joining pipe into the softened area of the pipe end and push until the required depth of the bell is achieved.
5. Remove the pipe to allow the bell joint area to harden and set, ready for assembly.
6. To join the pipe and fitting a coat of primer is applied to the outside of the pipe and the inside of the fitting
7. Solvent cement is applied to the outside of the pipe and inside the fitting
CBLM – Plumbing (Student Guide) v.1 Oct 2018 84
Skills for Employment Investment Programme (SEIP)
8. The pipe and fitting are pushed together and given a quarter turn and held for 15 seconds to set
On completion of this task you will be able to complete the following steps:
1. Collect tools, equipment and materials. 2. Cut the pipe as per required measurement with pipe cutter or hack saw. 3. Lay down the pipes in accordance with the planned/designed pipe run.
4. Assembled and fixed the pipes and pipe fittings in accordance with planned/designed pipe run.
5. Temporarily join pipes and fittings and make sure that the pipe in the run is facing the right direction.
6. Use a felt-tip pen to make alignment marks on all the joints where the fitting must face correctly.
7. Disassemble, keeping careful track of the order of installation.
8. Apply primer to each pipe end and each fitting.
9. Apply solvent/cement and join each pipe in order.
10. Checked the pipes, fittings and pipe runs for damage/quality of work.
11. Assembled pipe runs are measured/checked within tolerable dimensions/length in accordance with
design/specification.
12. Conduct leakage test using water. 13. Clean the workplace. 14. Restore the tools equipment and materials.
PVC/UPVC Pipe Joints
Sealant:
Same as Information Sheet 3.4.1 – Assemble Pipe Run (page 66 - 67)
Different types of Pipe clamps and fixtures: Same as Information Sheet 3.4.1 – Assemble Pipe Run (page 66 - 67)
Non-conformance:
Same as Information Sheet 3.4.1 – Assemble Pipe Run (page 66 - 67)
Finishing:
Same as Information Sheet 3.4.1 – Assemble Pipe Run (page 66 - 67)
Pipe Insulation:
Same as Information Sheet 3.4.1 – Assemble Pipe Run (page 66 - 67)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 85
Skills for Employment Investment Programme (SEIP)
Learning Outcome 4.4 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 86
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 4.1.1
1. Drilling holes in masonry, steel and timber surfaces. 2. Cutting brickwork and steel grinding steel surfaces. 3. Fusion welding of PPR pipes and fittings. 4. Heat up area to be worked on. 5. Cut PPR pipes to the required length by cutter.
Answer Key 4.2.1
1. Measuring Tape
2. Steel rule
3. Marker pen
4. Pipe vice
5. Tripod Chain Pipe Vice
6. Single Stroke Chain Pipe Cutter
7. Ratchet Type Chain Pipe Cutter
8. Three Wheel Type Pipe Cutter
9. Roller Pattern Pipe Cutter
10. PPR pipe cutter
CBLM – Plumbing (Student Guide) v.1 Oct 2018 87
Skills for Employment Investment Programme (SEIP)
Module 5: Carry out sewer pipeline installation
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to carry out sewer pipe
line installation which includes planning out for sewer pipe line installation,
gathering tools, equipment and materials, carrying out trenching and bedding
works, laying sewer pipe, finishing final pipe run, and cleaning and maintaining
the work area. It also includes information sheets, activity sheets, job sheets,
self-check quizzes and answer keys.
Nominal Duration: 28 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
5.1 Plan out for sewer pipe line installation
5.2 Gather tools, equipment and materials
5.3 Carry out trenching and bedding works
5.4 Lay sewer pipe
5.5 Finish final pipe run
5.6 Clean/maintain the work area
Performance Criteria:
1. Work activities are confirmed by making site visit/inspection.
2. Pipe run and elevation are identified in accordance with plumbing plans/specification.
3. Personal protective equipment (PPE) is selected and used.
4. Tools, equipment and materials are gathered and checked for usability.
5. Size of trench/excavation is made in accordance with workplace and plumbing plan requirement.
6. Grade/slope/pitch of trench is applied in accordance with workplace and plumbing plan requirement.
7. Bedding materials are laid in accordance to workplace and plumbing plan requirement.
8. Sewer pipes are laid on the trench in accordance with workplace and plumbing plan requirements.
9. Bell ended sewer pipes are laid by placing the bell end at the uphill side of the pipe run.
10. PVC sewer pipes are installed by using appropriate sealing/gluing materials.
11. Fittings are installed to complete the final run of the sewer pipe installation.
12. Final pipe run is checked for leaks and non-conformance to workplace and plumbing line requirements.
13. Covering materials are laid on top of the sewer pipe run in accordance with workplace and plumbing plan requirement.
14. Plumbing tools/equipment is cleaned and maintained.
15. Work area is cleaned and waste materials are disposed in accordance with workplace requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 88
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.1 - Plan Out for Sewer Pipeline Installation
Contents:
▪ Work activities: area cleaning, traffic re-routing, trench/excavation, tools and equipment gathering, materials gathering and stacking, concreting works
▪ Pipe line slope/pitch
Assessment criteria:
1. Work activities are confirmed by making site visit/inspection.
2. Pipe run and elevation are identified in accordance with plumbing plans/specification.
3. Pipe line slope/pitch is determined in accordance with plumbing plans/specification and result of site
visit.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine. ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape, cement, sand and plumbing plan/drawing. ▪ Pipe: sewer pipes (different diameter)
Learning Activity 5.1.1
Learning Activity Resources/Special Instructions/References
Plan out for sewer pipe line
installation
▪ Information Sheet: 5.1.1 ▪ Self-Check Quiz: 5.1.1 ▪ Answer Key: 5.1.1 ▪ https://www.piercecountywa.org/DocumentCenter/View/886/P02-
Building
Information Sheet 5.1.1
Learning Objective: to confirm the work activities related to plan out for sewer pipe line installation done in
the workplace.
Work activities: needed to be confirmed by making site visit/inspection when plan out for sewer pipe line installation in the workplace are:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 89
Skills for Employment Investment Programme (SEIP)
▪ Area clearing: The entire area of the sewer pipe line installation must be cleared to avoid obstacles
and free to work as per standard practice. ▪ Traffic re-routing: Signs and signals to be displayed and alternate routes to be showed so that
traffic can move safely. ▪ Trenching/excavation: Follow the standard procedure of lay outing for trenching and excavation
works in accordance with workplace and plumbing plan requirement. ▪ Tools and equipment gathering: Collect and gather required quantity of tools and equipment and
checked for usability. ▪ Materials gathering and stacking: Gather quality materials and stack suitable places for uses. ▪ Concreting works: Prepare concrete as per standard procedure and place/apply in accordance with
workplace and plumbing plan requirement.
Plumbing plans: ▪ Plumbing and piping plans clearly display where the fixtures, pipes and valves are. ▪ The job of the drain-waste part of the system is to carry waste water and sewage from sinks,
bathtubs, showers, toilets and water-using appliances such as dishwashers and washing machines and deliver those wastes to the septic tank or public sewer.
Sewer pipe runs and elevation:
▪ To start, you must determine how far the pipe needs to go and determine the elevation at which the pipe will be connected to the specific fixture or if it will be connected to another pipe.
Sewer pipe line slope/pitch:
▪ Be careful, a drop greater than ¼” per foot is not adequate as water will flow faster than solids. ▪ The recommended pitch for 4" pipe is 1/8" to 1/4" per foot.
Self-Check Quiz 5.1.1
Write the correct answer for the following:
1. What is the recommended pitch per foot for 4" pipe?
CBLM – Plumbing (Student Guide) v.1 Oct 2018 90
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.2 - Gather Tools, Equipment and Materials
Contents:
▪ Names of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plugs
▪ List of main tools, equipment and materials uses ▪ Sewer pipe sizes and uses
Assessment criteria:
1. Required tools, equipment and materials are identified in accordance with plumbing plan and result of site visit/inspection.
2. Sewer pipe sizes/schedules are identified and gathered. 3. Personal protective equipment (PPE) is selected and used. 4. Tools, equipment and materials are gathered and checked for usability.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape and plumbing plan/drawing
▪ Pipe: Sewer pipes (different diameter)
Learning Activity 5.2.1
Learning Activity Resources/Special Instructions/References
Gather tools, equipment and materials ▪ Information Sheets: 5.2.1, 5.2.2, 5.2.3, 5.2.4, 5.2.5 ▪ Self-Check Quiz: 5.2.1 ▪ Answer Key: 5.2.1
Information Sheet 5.2.1
Learning Objective: to identify and uses of the personal protective equipment in the workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 91
Skills for Employment Investment Programme (SEIP)
Personal Protective Equipment (PPE): Same as Information Sheet 1.1.1 – Gather and Check Tools, Equipment and Materials (page 8 - 9)
Information Sheet 5.2.2
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.2 – Carry out steel pipe cutting operations (page 10 - 12)
Information Sheet 5.2.3
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.3 – Carry out thread cutting operation (page 13 - 14)
Information Sheet 5.2.4
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Materials:
Sewer: A sanitary sewer or foul sewer is an underground carriage system specifically for transporting sewage from houses and commercial buildings through pipes to treatment or disposal. Sanitary sewers are part of an overall system called sewerage or sewage system.
Types of sewers according to material: 1. PVC sewer 2. UPVC sewer 3. Cast Iron (CI) sewer 4. Plain concrete and reinforced cement concrete sewers 5. Asbestos Cement (AC) sewer
1
PVC (polyvinyl chloride) is a common, strong but
lightweight plastic used in construction
2
uPVC pipe: If no plasticizers are added, it is known as
uPVC (un-plasticized polyvinyl chloride), rigid PVC.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 92
Skills for Employment Investment Programme (SEIP)
3
CI (Cast Iron) pipes: Used as a pressure pipe for
transmission of water, gas and sewage and as a water
drainage pipe
4
Concrete pipes: For heavy drainage water disposal,
concrete pipes of large diameters are used. Smaller
diameter pipes are used for small flows.
5
Asbestos Cement (AC) pipes: This kind of pipes are made
from a mixture of Portland cement and asbestos fibre and
used as vent pipes, soil pipes and rain water pipes. They
are very cheap compared to all but they can break easily.
Self-Check Quiz 5.2.1
Write the correct answer for the following:
1. Write the full name of PVC pipe.
2. Write the full name of UPVC pipe.
3. Write the full name of CI pipe.
Information Sheet 5.2.5
Learning Objective: to identify and uses of different types of plumbing fittings in the workplace.
Fittings: are used in pipe systems to connect straight pipes, adapt to different sizes or shapes and for other purposes.
PVC/UPVC pipe fittings:
Avaiable in different types and sizes, which are
used for PVC/UPVC pipe connections
Galvanized pipe (GI) fittings:
2 Avaiable in different types and sizes, which are used for GI pipe connections
CBLM – Plumbing (Student Guide) v.1 Oct 2018 93
Skills for Employment Investment Programme (SEIP)
Cast iron pipe fittings:
Avaiable in different types and sizes, which are
used for CI pipe connections
Concrete pipe fittings:
Avaiable in different types and sizes, which are
used for concrete pipe connections
Elbow/Bend:
This is most common types of pipe fitting used in plumbing works.
90 degrees
45 degrees
Tee (T) joint:
This is also common types of pipe fitting used in
plumbing works. It is available in equal or
unequal sizes.
Wye (Y)- joint:
This is a common type of pipe fitting used in sewer line and available in equal or unequal sizes.
Croos(X) joint:
This is also common type of pipe fitting used in
plumbing works and also available in equal or
unequal sizes.
Offset joint:
This is used in plumbing works with overcoming
offsets in the alignment.
Grating:
Gratings over drains and air vents are used
as filters, to block movement of large particles
and to allow movement of small particles.
Cowel:
This is used on top of the soil/waste/vent pipe
which cover the pipe and controls the way
gas/smoke flows out only.
Coupler:
It is used in pipe systems to connect
straight pipe, adapt to different sizes or shapes
and for other purposes, such as regulating
fluid flow.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 94
Skills for Employment Investment Programme (SEIP)
Socket:
It is also used in pipe systems to connect
straight pipe, adapt to different sizes or shapes
and for other purposes, such as regulating
fluid flow.
Multi-Croos(X) joint:
This is used in plumbing works and also available
in equal or unequal sizes.
Traps:
In plumbing, a trap is a device which has a shape that uses a bending path to capture water to prevent sewer gases from entering buildings. In domestic applications, traps are typically U, S, or P-shaped pipe located below or within a plumbing fixture. The most common of these traps in houses is referred to as a P-trap.
S-shaped
P-shaped
U-shaped
Do you know?
1. All fittings to be used as per instruction of the manufacturer. 2. Combination of different fittings (materials) should be avoided.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 95
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.3 - Carry Out Trenching and Bedding Works
Contents:
▪ Trench/excavation layout procedure ▪ Grade/slope of trench: methods of determining and applying ▪ Bedding materials: sand, gravel, concrete and bricks
Assessment criteria:
1. Trench/excavation area/line is laid out in accordance with plumbing plan and result of site visit. 2. Size of trench/excavation is made in accordance with workplace and plumbing plan requirement.
3. Grade/slope of trench is applied in accordance with workplace and plumbing plan requirement.
4. Bedding material is laid in accordance to workplace and plumbing plan requirement.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: Measuring tape (5m), steel rule, spirit level, shovel, spade, cold chisel, hammer, string lines, ▪ Equipment: trenching/digging equipment ▪ Materials: marking pen, pencil, marking powder, masking tape, bedding materials and plumbing
plan/drawing
Learning Activity 5.3.1
Learning Activity Resources/Special Instructions/References
Carry out trenching and bedding works ▪ Information Sheet: 5.3.1 ▪ Self-Check Quiz: 5.3.1 ▪ Answer Key: 5.3.1 ▪ http://www.mbwaterservicesboard.ca/pubs/specs/022180-
pipe-excavatio
Information Sheet 5.3.1
Learning Objective: to carry out trenching and bedding works for sewer pipe line installation in the
workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 96
Skills for Employment Investment Programme (SEIP)
Important activities:
To carry out trenching and bedding works the following activities need to perform as per plumbing plans and requirements:
1. Collect and study the plumbing plans/specification and visit the site.
2. Calculate the pipe runs according to planned route.
3. Lay out for trenching and excavation works.
4. Size of the trench/excavation in accordance to job requirement.
5. Protect the sides of trench to avoid sliding or erosion (if happen).
6. Apply grade/slope of trench as per specification and job requirement.
7. Spread bedding materials for safety of sewer pipe.
Trench and Bedding:
▪ Start by opening the trench. Be careful once the trench is open and follow all safety measures to protect workers inside and outside the trench.
▪ Remove all loose dirt at the trench bottom and grade the trench bottom so the pipe could be installed over a smooth surface.
▪ Sometimes it needs to place a bedding material to provide additional support to the sewer pipe, to reduce the possibility of ‘sag’ after the trench has been backfilled.
▪ Sand is the best material to use for bedding, but brick chips or gravel can also be used for bedding. ▪ Be careful on not to use sharp stone or other materials that sometimes can punctuate the sewer
pipe.
Grade/Slope:
▪ Proper slope of gravity drainage and sewer pipes is important so that liquids flow smoothly, which helps transport solids away without clogging.
▪ A pipe that is too flat will prevent waste from flowing away. It is also commonly thought that pipes that are too steep will allow liquids to flow so quickly that solids will not be carried away.
Standard horizontal drainage pipe slope:
▪ According to the International Plumbing Code, drainage pipes should be run with a uniform slope at the following minimum pitches:
Pipe diameter Minimum slope
2 ½" or smaller 1/4" per foot
3" to 6" 1/8" per foot
8" or larger 1/16" per foot
Large diameter sewer pipe slopes:
▪ Large sewer lines require calculations to determine the proper pitch. In general, sewer mains should be designed to have a flow rate of 2 feet-per-second during peak dry-weather conditions.
▪ Flow rates are usually kept below 10 feet per second. For floor rates greater than 10 feet-per-second, the pipes should be designed with anchors or other means of preventing the pipe from shifting.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 97
Skills for Employment Investment Programme (SEIP)
Bedding and support materials:
▪ It is important in determining and ordering the correct quantities of bedding material for the sanitary drainage systems in a workplace.
▪ If the correct procedures are not adhered to drainage materials can be damaged and leaking may result in structural damage to buildings.
▪ Drainage systems must be installed in stable ground that is free from rocks and sharp objects. ▪ When laying pipes in loam, rock, shale, gravel or clay ground the pipe must be laid on a suitable
bedding material such as:
- Sand - Broken brick/crushed stone - Cement mortar - Cement concrete
• The same material used for bedding can be used for side support and for overlay zones.
Concrete bedding
Self-Check Quiz 5.3.1
Read the following statements and write/mark true or false accordingly:
No. Description True False
1. Drainage systems must be installed in stable ground that is free from rocks
and sharp objects.
2. According to the International Plumbing Code, drainage pipes should be run
with a uniform slope/pitch for 2½ inches diameter is 1/4" per foot.
3. According to the International Plumbing Code, drainage pipes should be run
with a uniform slope/pitch for 3 to 6 inches diameter is 1/2" per foot.
4. According to the International Plumbing Code, drainage pipes should be run
with a uniform slope/pitch for 8 inches or larger diameter is 1" per foot.
5. The best material to use for bedding material is sand.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 98
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.4 - Lay Sewer Pipe
Contents:
▪ Sewer pipe laying procedure ▪ Bell ended sewer pipes ▪ PVC sewer pipes ▪ Alignment and pipe elevation ▪ Sealing/gluing materials: solvents, cement, sealant (plastic, rubber, synthetic silicone, PVC primer
Assessment criteria:
1. Sewer pipes are laid on the trench in accordance with workplace and plumbing plan requirements. 2. Bell ended sewer pipes are laid by placing the bell end at the uphill side of the pipe run. 3. PVC sewer pipes are installed by using appropriate sealing/gluing materials. 4. Alignment and pipe elevation are checked in accordance to workplace and plumbing plan requirements.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, spirit level, shovel, spade, cold chisel, hammer, string lines, ▪ Equipment: trenching/digging equipment ▪ Materials: marking pen, pencil, marking powder, masking tape and plumbing plan/drawing
Learning Activity 5.4.1
Learning Activity Resources/Special Instructions/References
Lay sewer pipe ▪ Information Sheet: 5.4.1, 5.4.2 ▪ Self-Check Quiz: 5.4.1 ▪ Answer Key: 5.4.1 ▪ https://www.ehow.com/how_5063577_lay-sewer-pipe.html
Information Sheet 5.4.1
Learning Objective: to lay sewer pipe on the trench in the workplace.
Tips for installation of new sewer lines
CBLM – Plumbing (Student Guide) v.1 Oct 2018 99
Skills for Employment Investment Programme (SEIP)
▪ Map sewer line route: Check where the underground hazards are located and then map out the route of the sewer lines. This will help to not only see where it will go, but also plan for materials will need.
▪ Lay out pipes: Lay out the pipes according to plan before make any permanent connections. Once everything fits in place, then can cement the pipes together.
▪ Keep proper grade: When the grade of the ground is sloping downward do not need to have any type of extra help for the sewage to flow to the tank. If the land is level, then dig trench for the sewer lines at a gradual slope so the waste will naturally travel in the direction towards the tank and not sit still in the pipes.
▪ Install plenty of traps: Set sufficient numbers of traps at various places along the sewer line so that a plumber can access the pipes to flush them out.
▪ Insulate pipes: The sewer pipe will remain safe and avoid any damage if insulate the pipes with sand or brick/stone chips, instead of placing the sewer lines on the bare ground.
How to Install a Sewer Pipe?
▪ A sewer pipe needs to be installed carefully with adequate slope. ▪ The installation methods and processes are almost identical for all types of pipe or culvert materials. ▪ Depending on the sewer pipe material, things could be easier or more complicated because the
installation process might be more challenging, more equipment and labour might be needed.
Lay the sewer pipe:
▪ Once the select portion of trench has been prepared, lay the sewer pipe in the trench. ▪ It is recommended to start at the lower end of the pipe run, up to the higher elevation. ▪ If the sewer pipe has a bell end; the bell end must be placed on the uphill side of the pipe run,
reducing the possibility of leakage. ▪ Insert the male end of the pipe into the female end and twist a little bit. ▪ Install a string along the pipe run to ensure the alignment and pitch are being followed correctly. ▪ The string must be installed with the same slope as the pipe will be, but just one foot over the
finished level.
Self-Check Quiz 5.4.1
Read the following statements and write/mark true or false accordingly:
No. Description True False
1. The sewer lines are an integral part of the waste water system.
2. Traps in a sewage line are not important to being able to make repairs or
remove clogs.
3. To safe the sewer pipe and avoid any damage, insulate the pipes with sand
or brick/stone chips plays important role, instead of placing the sewer lines
on the bare ground.
4. When the grade of the ground is sloping downward, you do not need to have
any type of extra help for the sewage to flow to the tank.
5. To reduce the possibility of leakage, the bell end of pipe must be placed on
the downhill side of the pipe run.
Information Sheet 5.4.2
Learning Objective: to install PVC sewer pipes in the workplace.
How to install PVC sewer pipe (pictorial representation):
CBLM – Plumbing (Student Guide) v.1 Oct 2018 100
Skills for Employment Investment Programme (SEIP)
Same as Learning Outcome 4.3 – Perform PVC/UPVC Pipe Run Assembly (page 81 - 84)
Bell Joint in PVC pipes using the Traditional Method: Same as Information Sheet 4.3.1 – Perform PVC/UPVC Pipe Run Assembly (page 81 - 84)
Bell Joint in PVC pipes using the Heat Gun:
Same as Information Sheet 4.3.1 – Perform PVC/UPVC Pipe Run Assembly (page 81 - 84)
Sealing/gluing materials: Sealant is a substance used to block the passage of fluids through the surface or joints or openings in materials. It may be weak or strong, flexible or rigid, permanent or temporary. These are not adhesives but some have adhesive qualities and are called adhesive-sealants or structural sealants. The followings may include as sealing/gluing materials to carry out sewer pipe line installation: ▪ Solvents ▪ Cement ▪ Plastic based sealants ▪ Rubber based sealants ▪ Synthetic sealants ▪ PVC primer ▪ Silicon sealants
Remember:
• Once the pipe has become softened in the area required for the bell bring the other pipe closer ready to form the bell before the heat is lost.
• Apply primer to each pipe end and each fitting.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 101
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.5 - Finish Final Pipe Run
Contents:
▪ Leaks and non-conformance: leaks, pipe size, fitting size, pipe run slope/grade, pipe damage ▪ Covering materials: sand, gravel and concrete
Assessment criteria:
1. Fittings are installed to complete the final run of the sewer pipe installation. 2. Final pipe run is checked for leaks and non-conformance to workplace and plumbing line requirements. 3. Re-works or revision is made where necessary. 4. Covering materials are laid on top of the sewer pipe run in accordance with workplace and plumbing
plan requirement.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, spirit level, shovel, spade, cold chisel, hammer, string lines, ▪ Equipment: trenching/digging equipment ▪ Materials: marking pen, pencil, marking powder, masking tape, covering materials and plumbing
plan/drawing
Learning Activity 5.5.1
Learning Activity Resources/Special Instructions/References
Finish final pipe run ▪ Information Sheet: 5.5.1 ▪ Self-Check Quiz: 5.5.1 ▪ Answer Key: 5.5.1
Information Sheet 5.5.1
Learning Objective: to finish final pipe run in the workplace.
Leaks and Non-conformance: The following points are important to consider as non-conformance: ▪ Leaks ▪ Pipe size (diameter) ▪ Pipe fitting size
CBLM – Plumbing (Student Guide) v.1 Oct 2018 102
Skills for Employment Investment Programme (SEIP)
▪ Pipe run slope/grade ▪ Pipe damage
Covering materials: The following materials may be used as covering materials: ▪ Excavated soil ▪ Sand ▪ Brick chips/Stone chips ▪ Cement mortar ▪ Cement concrete ▪ Warning tape
Final pipe run:
▪ It is probable that the last portion of the run will need just a fraction of a pipe. ▪ Be aware that it will also need additional fittings to complete the installation. ▪ Once the pipe has been installed completely, check for any pipe that could be disconnected, broken
or not installed properly. ▪ Place the sand and/or gravel over the pipe, enough to cover at least 10” over the sewer pipe. ▪ Start to compact the material with a rammer or any other compaction equipment suitable for the
type of pipe being installed. ▪ On long pipe runs, this process could be started once the pipe has been installed and while working
on the next pipe segment. ▪ It is important to install a warning tape over the first layer of compacted soil, so others will be aware
when excavating that a pipe is located under the detectable warning tape.
Backfilling of excavations:
• Backfilling is the replacement of excavated earth into a trench around the embedment area or against a trench.
• To backfill of a trench can be done by using the same material that was originally excavated, provided it is free from any rocks, builders' waste or other materials that may damage the pipe.
Calculating material quantities: ▪ To calculate volume, it needs to know the width, length and depth (at the deep end and the shallow
end) of the trenches. ▪ Volume to be excavated, V = Length x Width x Depth (average)
Do you know?
• The backfill of a trench can be done by using the same material that was originally excavated, but must be free from any rocks, builders' waste or other materials that may damage the pipe.
• For house sewer inspection pit must be provided after 20 feet (6.0 m) apart in straight line and in every turning point.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 103
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 5.5.1
Write the correct answer of the following:
1. Why warning tape is used in sewer pipe line installation?
2. What kind of materials should not use for backfilling?
3. How you can calculate the volume of material in excavating from the trench?
4. What is the maximum distance in between house sewer inspection pits that must be provided in a
straight line?
CBLM – Plumbing (Student Guide) v.1 Oct 2018 104
Skills for Employment Investment Programme (SEIP)
Learning Outcome 5.6 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 105
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 5.1.1
1. The recommended pitch for 4" pipe is 1/8" to 1/4" per foot.
Answer Key 5.2.1
1. Polyvinyl chloride pipe 2. Un-plasticized polyvinyl chloride pipe 3. Cast Iron pipe
Answer Key 5.3.1
1. True 2. True 3. False 4. False 5. True
Answer Key 5.4.1
1. True 2. False 3. True 4. True 5. False
Answer Key 5.5.1
1. It is important to install a warning tape over the first layer of compacted soil, so others will be aware when excavating that a pipe is located under the detectable warning tape.
2. Any type of sharp pointed materials, builders' waste or other materials that may damage the pipe should not be used for backfilling.
3. To calculate the volume for excavation, V = Length x Width x Depth (average). 4. For house sewer inspection pit must be provided after 20 feet (6.0 m) apart in straight line and every
turning point.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 106
Skills for Employment Investment Programme (SEIP)
Module 6: Carry out plumbing fixtures installation
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to carry out plumbing
fixtures installation which includes preparing for plumbing fixture installation,
gathering tools, equipment and materials, installing new toilet bowl (commode),
installing other plumbing fixtures, and cleaning and maintaining the work area. It
also includes information sheets, activity sheets, job sheets, self-check quizzes,
and answer keys.
Nominal Duration: 60 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
6.1 Prepare for plumbing fixture installation
6.2 Gather tools, equipment and materials
6.3 Install a new toilet bowl (commode)
6.4 Install other plumbing fixtures
6.5 Clean/maintain the work area
Performance Criteria:
1. Work activities are confirmed by making site visit/inspection to install plumbing fixtures as per plan
and workplace requirements.
2. Personal protective equipment (PPE) is selected and used.
3. Tools, equipment and materials are gathered and checked for usability.
4. The new toilet bowl is placed on the flange aligning the bolt holes with the bolts of the flange and
wax ring in its proper place.
5. Nuts with washers are tightened squarely without over tightening.
6. Additional sealing material is applied around the base of the bowl in accordance to workplace
requirements.
7. The water tank is installed on the bowl in accordance with manufacturer’s instruction.
8. Plumbing fixtures are installed in accordance with plumbing plan and following manufacturer’s
instruction/specification.
9. Check newly installed plumbing fixtures for leaks and non-conformance with workplace
requirements.
10. Plumbing tools/equipment is cleaned and maintained.
11. Work area is cleaned and waste materials are disposed of in accordance with workplace
requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 107
Skills for Employment Investment Programme (SEIP)
Learning Outcome 6.1 - Prepare for Plumbing Fixture Installation
Contents:
▪ Work activities for installation/repair of toilet bowl (commode), shower, bath tub, wash basin, kitchen sink, urinals, water closet, bidets, drinking fountains, terminal valves/faucets
▪ Plumbing fixture: toilet bowl (commode), shower, bath tub, wash basin, kitchen sink, urinals, water closet, bidets, drinking fountains, terminal valves/faucets
Assessment criteria:
1. Work activities are confirmed in accordance with plumbing plan and workplace requirements. 2. Work site is visited and prepared prior to installation works.
3. Plumbing fixture is determined, collected and checked for workability and quality.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round), cold chisel, hammer
▪ Equipment: pipe threading machine, power hacksaw, drill press, angle grinder, welding machine ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape, cement, sand and plumbing plan/drawing ▪ Fixtures: toilet bowl (commode), shower, bath tub, wash basin, kitchen sink, urinals, water closet,
bidets, drinking fountains, terminal valves/faucets
Learning Activity 6.1.1
Learning Activity Resources/Special Instructions/References
Prepare for plumbing fixture installation ▪ Information Sheets: 6.1.1, 6.1.2 ▪ Self-Check Quiz: 6.1.1 ▪ Answer Key: 6.1.1 ▪ https://ptpnaples.com/plumbing-fixture-installation-
repair/ ▪ https://homeguides.sfgate.com/install-plumbing-new-
home-56399.html
CBLM – Plumbing (Student Guide) v.1 Oct 2018 108
Skills for Employment Investment Programme (SEIP)
Information Sheet 6.1.1
Learning Objective: to confirm the work activities related to prepare for plumbing fixture installation in the
workplace.
Work activities: The following work activities are needed to be confirmed by making site visit/inspection when installation of plumbing fixtures in a workplace: ▪ Tools and equipment gathering: Collect and gather required quantity of tools and equipment and
checked for usability. ▪ Materials gathering and stacking Gather quality pipes and other materials and stack suitable places
for uses. ▪ Plumbing fixtures and fittings: Collect and gather good quality plumbing fixtures and fittings as per
workplace requirements.
Plumbing plans: Plumbing and piping plans clearly display where the fixtures, pipes and valves are. Plumbing and piping plans are of great importance to design a house or building plan.
Installation of plumbing fixtures: ▪ Toilet bowl (Commode) ▪ Water closet (Pan) ▪ Wash hand basin (WHB) ▪ Kitchen sink ▪ Shower ▪ Bath tub ▪ Urinals
CBLM – Plumbing (Student Guide) v.1 Oct 2018 109
Skills for Employment Investment Programme (SEIP)
▪ Drinking fountains ▪ Terminal valve/faucet ▪ Bidet
Information Sheet 6.1.2
Learning Objective: to determine, collect and check plumbing fixtures for workability and quality.
Plumbing Fixtures: A plumbing fixture is an exchangeable device which can be connected to a plumbing system to collect or receive and deliver or drain water and human waste.
Water closet (Commode):
This is used to collect and remove human waste.
Long Pan:
This is also used to collect and remove human
waste.
Wash Basin: is used to collect water for wash hands and face. These maybe of different types.
Pedestal type
Rectangular shape
Round shape
Glass bowl shape
Kitchen sink:
This is a bowl-shaped plumbing fixture used for
dishwashing and other purposes.
Shower:
This is used for spray warm or hot water to wash
or bathe oneself.
Bath tub: is a large or small container used for
holding water in which a person or a person’s pet
may bathe.
Urinals: is a sanitary plumbing fixture for urination only and predominantly used by males.
Squatting type
Bowl type
Sensor-operated urinals
Drinking fountains:
This is used for drinking purposes.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 110
Skills for Employment Investment Programme (SEIP)
Terminal valve/faucet:
Terminal valve/faucet is used for dishwashers,
ice makers, humidifiers or other purposes.
Bidet:
Bidet is installed in a bathroom for washing the
genitalia, perineum, inner buttocks and anus of
the human body.
Hand dryer:
It is fixed in wall and used as automatic hand
dryer.
Sensor basin faucet:
It is fixed with wash basin and used as automatic
hand wash with water.
Self-Check Quiz 6.1.1
Check your understanding by identifying the following plumbing fixtures:
No. Picture Name of the fixture
1
2
3
4
5
CBLM – Plumbing (Student Guide) v.1 Oct 2018 111
Skills for Employment Investment Programme (SEIP)
Learning Outcome 6.2 - Gather Tools, Equipment and Materials
Same as Learning Outcome 1.1 – Gather and Check Tools, Equipment and Materials (page 8 - 15)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 112
Skills for Employment Investment Programme (SEIP)
Learning Outcome 6.3 - Install A New Toilet Bowl (Commode)
Contents:
▪ Toilet bowl (commode) installation ▪ Accessories: wax ring, nuts & bolts, washers etc. ▪ Water tank installation with necessary accessories ▪ Sealing materials: cement concrete, grommet (rubber & plastic), sealants (rubber, silicone, plastic and
synthetic), wax seal
Assessment criteria:
1. Toilet bowl flange is installed securely making sure the bolts are in place. 2. A new wax ring is placed at the bottom of the toilet bowl accurately.
3. The new toilet bowl is placed on the flange aligning the bolt holes with the bolts of the flange and wax
ring in its proper place.
4. Nuts with washers are tightened squarely without over tightening.
5. Apply additional sealing material around the base of the bowl in accordance to workplace requirements.
6. The water tank is installed on the bowl in accordance with manufacturer’s instruction.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round), cold chisel, hammer
▪ Equipment: pipe threading machine, power hacksaw, drill press ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape, cement, sand and plumbing plan/drawing ▪ Plumbing fixture: toilet bowl (commode), water tank and manufacturer’s instruction / specification /
manual
LEARNING ACTIVITY 6.3.1
Learning Activity Resources/Special Instructions/References
Install a new toilet bowl (commode) ▪ Information Sheet: 6.3.1 ▪ Job Sheet 5 ▪ https://www.youtube.com/watch?v=wM-6bgV7G5s ▪ https://www.wikihow.com/Install-a-Toilet
CBLM – Plumbing (Student Guide) v.1 Oct 2018 113
Skills for Employment Investment Programme (SEIP)
Information Sheet 6.3.1
Learning Objective: to install a new toilet bowl (commode) in the workplace.
Install a new toilet bowl (commode): 1. Collect commode set, necessary tools, equipment, materials and drawing. 2. Mark the floor and wall area as per layout. 3. Cut the floor/wall as per measurement and drawing. 4. Place the commode on the floor to mark the drill point on the floor. 5. Drill the marking points using drill machine. 6. Put the rowel plug into the hole. 7. Place the commode on the floor. 8. Put the commode screw in the drilling point and tighten properly. 9. Fix the seat and seat cover with commode. 10. Level the installation area of commode using white cement mixture 11. Connect soil pipe with commode as per layout. 12. Connect angle valve with cistern and commode using connection pipe. 13. Mark the area to set the push shower 14. Drill the drilling point using drill machine to fix the push shower. 15. Fix push shower stand with screw. 16. Connect the push shower with two-in-one bibcock. 17. Switch ON/OFF the commode low down and push shower; check the performance. 18. Clean the workplace and restore the tools, equipment and extra materials.
A new toilet bowl (commode) installation activities (pictorial representation):
Place the commode’s pan on the floor in the exact
position it is to be installed.
Hold the pan firmly in position and using a pencil
mark the shape of the pan's pedestal on the floor.
Remove the pan and place in a safe position.
Use an angle grinder to cut the area where the hole
must be made in the concrete floor
Use hammer and chisel to open up hole in the floor
and fit the closet bend
Drill holes in concrete for rowel bolts to be inserted
Place the floor flange over the closet bend until the
flange rests on the finished floor.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 114
Skills for Employment Investment Programme (SEIP)
Using uPVC make a joint to form the soil pipe
Put two rowel bolts with their threaded ends up into
the flange slots.
Turn the bowl upside down on protective waste
newspaper or wooden strips to avoid scratching.
Set the wax gasket over the horn
Turn the bowl right side up and set it on the flange
Setting the bowl on the flange with the bolts through
the holes of the bowl
Place a washer and nut on each bolt tightening
each alternately until the bowl is set and the nut
caps are fitted.
Ensure that the bowl is in a level position
Mark out the route of the cold-water supply to the
commode and push shower for the installation of
the angle stopcocks
Use an angle grinder to cut the chase in the walls
Remove the chased area using a hammer and cold
chisel.
Assemble the cistern/flashing tank
CBLM – Plumbing (Student Guide) v.1 Oct 2018 115
Skills for Employment Investment Programme (SEIP)
Fix the washers of the bolts that secure the cistern
to the bowl
Pull the anchoring bolts from the inside of the
cistern
Tighten the lock nuts in position
Secure the cistern in position on the bowl
Prepare to install the seat and seat cover
Fasten the seat and seat cover in position
Install angle stopcocks and connect to the cold-
water supply
Connect cold water supply from the angle stopcock
to the cistern/flashing tank
Install and connect the push shower with the angle
stopcock
Join the commode’s outlet to the uPVC trap and
soil pipe with primer and solvent cement
CBLM – Plumbing (Student Guide) v.1 Oct 2018 116
Skills for Employment Investment Programme (SEIP)
JOB SHEET 5
Qualification: Plumbing
Learning unit: Install a new toilet bowl (commode)
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: Thread tape (Teflon), cement, sand, brick/stone chips, commode set, push shower, angle stopcocks and connection pipes.
Tools and equipment: Measuring tape, marking pen/pencil, grinding machine, pipe range, hack saw, pipe cutter, chisel, hammer, flat file, die-stock, oil-can, steel wire brush, elbow, bend, socket, tee (T), union.
Performance Criteria 1. Install commode set as per drawing without any error. 2. Correct hand and power tools are used safely. 3. Wax seal is installed correctly. 4. Cistern is installed securely in correct position. 5. Commode must be level and operate without leakages. 6. Push shower must operate without leakages. 7. Connection to soil pipe should be without leakages.
Note: ▪ Install a commode as per the drawing ▪ Connect the commode with angle stopcock ▪ Install a push shower as per drawing ▪ Connect push shower to an angle stopcock
Procedure: 1. Collect and gather tools, equipment and materials to needed 2. Place the floor flange over closet bend until the flange rests on the finished
floor 3. Make a joint with uPVC 4. Put two rowel bolts with their threaded ends up into the flange slots 5. Turn the commode upside down set the wax gasket over the horn 6. Turn the bowl upright and set it on the flange with the bolts through 7. Place nut on bolts tighten 8. Ensure that the bowl is level 9. Fix the cistern in position with seat and seat cover 10. Connect both commode and push shower with angle stopcocks
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
CBLM – Plumbing (Student Guide) v.1 Oct 2018 117
Skills for Employment Investment Programme (SEIP)
Sealing material: ▪ Solvents ▪ White cement ▪ Cement/concrete ▪ Plastic grommet ▪ Plastic based sealants ▪ Rubber grommet ▪ Rubber based sealants ▪ Synthetic sealants ▪ Wax seal ▪ PVC primer ▪ Silicon sealants
Individual Activity:
▪ Watch the video on ‘How to install a new toilet bowl (commode)’ and summarise the key points (if facilities available)
▪ Install the commode following the activity sheet and Job Sheet 5 (see above)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 118
Skills for Employment Investment Programme (SEIP)
Learning Outcome 6.4 - Install Other Plumbing Fixtures
Contents:
▪ Wash hand basin ▪ Shower ▪ Bath tub ▪ Kitchen sink ▪ Urinals ▪ Water closet ▪ Bidets ▪ Drinking fountains ▪ Terminal valves/faucets ▪ Leaks and non-conformance: leaks, damaged fixtures, broken/damaged fittings, wrong pipe size,
wrong fitting size, damage flooring/walls
Assessment criteria:
1. Plumbing fixtures are installed in accordance with plumbing plan and following manufacturer’s instruction/specification.
2. Check newly installed plumbing fixtures for leaks and non-conformance with workplace requirements. 3. Reworks/adjustment is carried out in accordance with workplace requirements.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round), cold chisel, hammer
▪ Equipment: pipe threading machine, power hacksaw, drill press ▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape
(Teflon), welding rod, masking tape, cement, sand and plumbing plan/drawing ▪ Plumbing fixture: shower, bath tub, wash basin, kitchen sink, urinals, water closet, bidets, drinking
fountains, terminal valves/faucets
Learning Activity 6.4.1
Learning Activity Resources/Special Instructions/References
Install other plumbing fixtures ▪ Information Sheet: 6.4.1 ▪ Job Sheet 6 ▪ Self-Check Quiz: 6.4.1 ▪ Answer Key: 6.4.1 ▪ https://www.youtube.com/watch?v=a_8-zz8tc7U
CBLM – Plumbing (Student Guide) v.1 Oct 2018 119
Skills for Employment Investment Programme (SEIP)
Information Sheet 6.4.1
Learning Objective: to install other plumbing fixtures in the workplace.
Install a wash hand basin: 1. Collect basin with all necessary accessories, tools, equipment, materials and drawing. 2. Mark the area of basin, looking glass, shelf, soap case, trowel rail and liquid dispenser as per
drawing and layout. 3. Drill the marking points using drill machine. 4. Put the rowel plug into the hole 5. Fix the basin screw/nut into the hole. 6. Fix basin waste and pillar cock with basin. 7. Place washbasin with basin screw as per layout. 8. Connect bottle trap with basin and waste line. 9. Connect the angle stop cock with pillar cock. 10. Level the installation area of wash basin using white cement. 11. Place looking glass shelf over the basin using screw. 12. Set mirror over the glass-shelf using screw. 13. Fix soap case/liquid dispenser in the wall using screw 14. Hang the towel rail in the wall using screw. 15. Conduct leakage test of wash basin and check the clear drainage. 16. Clean the workplace and restore the tools, equipment and extra materials.
Wash hand basin, Fitting and Accessories:
Wash hand Basin (wall hanged/cantilever)
Used to collect water to wash hands and face
Pillarcock
This faucet controls the water into the wash basin
Angle Stopcock
Used to control the hot and cold water supply
Basin waste
This fitting is used to enable a plug to be inserted
to keep the water inside the basin
Bottle trap
This is a trap that distributes waste water from the
basin
Glass shelf
To store toiletries on the shelf
CBLM – Plumbing (Student Guide) v.1 Oct 2018 120
Skills for Employment Investment Programme (SEIP)
Towel rail
This is used to hang towels on it
Mirror
This is used to reflect an image
Liquid soap case
It is used to dispense liquid soap to wash hands
Soap case
This is used to hold soap in the case
A new wash hand basin installation activity (pictorial representation):
Use the appropriate sealing material to seal the
area for the basin waste to be installed.
Insert the waste into sealing material
Apply the appropriat sealing material on the back
washer
Fit the back washer in place
Tighten the lock nut for basin waste
Unscrew the back nut and washer from the new
pillar cock
CBLM – Plumbing (Student Guide) v.1 Oct 2018 121
Skills for Employment Investment Programme (SEIP)
Place the washer in position ready to install
Place the pillar cock in the hole of the basin
Place the back nut onto the threaded section
under the basin
Tighten the back nut of the pillar cock with the help
of a box spanner
Securely fit the pillar cock
Connect flexi connector to the cold water supply to
the pillar cock and fix to the angle stopcock in
position
Mark out the position of the wash hand basin, the
centre lines of the cold water supply and the holes
through the wall for the cold water supply by using
a pencil and tape
Mark the position of the centre line of the waste
pipe
Drill the hole through the wall for the cold water
pipe
Cut the chase area as marked on the wall and floor
by using hammer and cold chisel
CBLM – Plumbing (Student Guide) v.1 Oct 2018 122
Skills for Employment Investment Programme (SEIP)
Mark the position of the centre line of the waste
pipe
Fit two numbers semi concealed brackets in the
wall
Place the basin level against the finished wall
surface at the correct height.
Insert the rowel plugs into the holes
The basin is fitted in postion to the wall onto the
two semi concealed brackets
Fix bottle trap to the waste
Scan wall for any electrical or water pipes to locate
safe drilling area
Mark out the position for mirror fixing
Mark out the position of the shelf’s brackets
Drill the holes and insert plugs into hole
Place glass shelf into position
Fix towel rail to wall
CBLM – Plumbing (Student Guide) v.1 Oct 2018 123
Skills for Employment Investment Programme (SEIP)
Apply adhesive to back of the mirror
After levelling place the temporary supports in
position
Place mirror onto the temporary supports
Press firmly the mirror into position and leave for
adhesive to set
Completed mirror in position
CBLM – Plumbing (Student Guide) v.1 Oct 2018 124
Skills for Employment Investment Programme (SEIP)
JOB SHEET 6
Qualification: Plumbing
Learning unit: Install a wash hand basin
Learner name:
Personal protective equipment (PPE):
Hand gloves, visibility vest, safety goggles, safety boots, hard hat and dust mask
Materials: Thread tape (Teflon), cement, sand, basin, basin waste, pillar cock, angle stop cock, glass shelf, mirror, liquid soap dispenser, soap case
Tools and equipment: Measuring tape, hack saw, pencil, pipe vice, tripod pipe vice, angle grinder,
hammer action drill and masonry bits, hammer, cold chisel, and screw drivers,
combination pliers, pipe wrench, adjustable wrench basin spanner and box
spanner
Performance Criteria 1. Basin is Installed as per drawings 2. Shelf, Mirror and Towel rail are installed as per drawing 3. Waste line and water supply are installed in correct position 4. All fittings and fixtures are correctly installed and sealed with sealing
compound. 5. No leaks are present in system. 6. All fittings and fixtures are secured correctly. 7. Basin is connected to floor drain correctly.
Measurement: ▪ The measurement must be 750 mm to the top of the basin from the floor.
Note:
▪ Fix pillar cock to basin. ▪ Fix basin’s waste outlet using the appropriate sealing compound and
fixings. ▪ Install wall hung single semi-concealed basin brackets fixed with rawl
plugs. ▪ Install a bottle trap. ▪ PVC waste pipe must be cased into the wall/ floor and be connected to
the floor drain. ▪ Install an angle stopcock at the basin. ▪ Connect the ½“ cold water to the pillar cock with flexible connectors.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 125
Skills for Employment Investment Programme (SEIP)
Procedure: 1. Collect tools, material and drawing. 2. Mark the area of basin, looking glass, shelf, soap case, trowel rail and
liquid dispenser as per drawing and layout. 3. Drill the marking points using drill machine. 4. Put the rowel plug into the hole 5. Fix the basin screw/nut into the hole. 6. Fix basin waste and pillar cock with basin. 7. Place washbasin with basin screw as per layout. 8. Connect bottle trap with basin and waste line. 9. Connect the angle stop cock with pillar cock. 10. Level the installation area of wash basin using white cement. 11. Place looking glass shelf over the basin using screw. 12. Set mirror over the glass-shelf using screw. 13. Fix soap case/liquid dispenser in the wall using screw. 14. Hang the towel rail in the wall using screw. 15. Conduct leakage test of wash basin and check the clear drainage. 16. Clean the workplace and restore the tools, equipment.
Learner signature: Date:
Assessor signature: Date:
Quality Assurer signature:
Date:
Assessor remarks:
Leaks and Non-conformance: ▪ Leaks ▪ Damage fixtures ▪ Broken/damaged fittings ▪ Wrong pipe size ▪ Wrong fitting size ▪ Damage flooring/walls
Individual Activity:
▪ Watch the video on ‘How to install a wash hand basin’ and summarise the key points (if facilities available).
▪ Install the commode following the activity sheet and Job Sheet 6 (see above)
SELF-CHECK QUIZ 6.4.1
Identify the following picture and write their names and what they are used for:
No. Picture Names and Used for
1.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 126
Skills for Employment Investment Programme (SEIP)
2.
3.
4.
5.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 127
Skills for Employment Investment Programme (SEIP)
Learning Outcome 6.5 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 128
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 6.1.1
1. Toilet bowl (Commode) 2. Water closet (Pan) 3. Wash hand basin (WHB) 4. Kitchen sink 5. Bath tub
Answer Key 6.4.1
1. Wash hand Basin: used to collect water to wash hands and face. 2. Pillarcock: used to control the water into the wash basin. 3. Angle Stopcock: used to control the hot and cold water supply. 4. Basin waste: used to enable a plug to keep the water inside the basin. 5. Soap case: used to hold soap in the case.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 129
Skills for Employment Investment Programme (SEIP)
Module 7: Perform pressure testing of piping system
MODULE CONTENT
Module Descriptor: This module covers the skills, knowledge and attitudes to perform pressure
testing of piping system which includes preparing for pressure testing, gathering
tools, equipment and materials, carrying out pressure testing, and cleaning and
maintaining the work area. It also includes information sheets, activity sheets,
job sheets, self-check quizzes and answer keys.
Nominal Duration: 24 hours
Learning Outcomes:
Upon completion of the module, the student/trainee will be able to:
7.1 Prepare for pressure testing
7.2 Gather tools, equipment and materials
7.3 Carry out pressure testing
7.4 Clean/maintain the work area
Performance Criteria:
1. Work activities are identified in accordance with plumbing plan and workplace requirements.
2. Maximum test pressure is determined in accordance with plumbing plan/design specification.
3. Pressure testing method is identified in accordance with plumbing plan/workplace requirements.
4. Piping system connections are reviewed and checked for tightness/integrity.
5. Devices, fixture or components in the piping systems that needs to be isolated is shut off to avoid damage.
6. Required tools, equipment and materials are identified in accordance with plumbing plan and workplace procedure on pressure testing.
7. Pressure testing tools, equipment and materials are collected and checked for usability/accuracy.
8. Personal protective equipment (PPE) is gathered and strictly used.
9. Preliminary, intermediate and final test pressures are applied progressively into the system in accordance with workplace pressure testing plan/procedure.
10. Appropriate Leak testing method is applied for each applied pressure to determine presence of leaks.
11. Leak testing result is reported to the concern person.
12. Test results are recorded in accordance with workplace requirements.
13. Safety precaution is observed when performing pressure testing.
14. Plumbing tools/equipment is cleaned and maintained.
15. Work area is cleaned and waste materials are disposed of in accordance with workplace requirements.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 130
Skills for Employment Investment Programme (SEIP)
Learning Outcome 7.1 - Prepare for Pressure Testing
Contents:
▪ Work activities for pressure testing: checking tightness of valves/fittings, measuring pipe runs, identifying of pipe run for pressure testing, identifying of fittings to be isolated and isolating system components
▪ Pressure testing method: pneumatic testing and hydrostatic testing
Assessment criteria:
1. Work activities are identified in accordance with plumbing plan and workplace requirements. 2. Maximum test pressure is determined in accordance with plumbing plan/design specification.
3. Pressure testing method is identified in accordance with plumbing plan/workplace requirements.
4. Piping system connections are reviewed and checked for tightness/integrity.
5. Devices, fixture or components in the piping systems that needs to be isolated is shut off to avoid
damage.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round), cold chisel, hammer
▪ Equipment: air compressor, water pump, nitrogen pump/tank, pressure gauge and quick connect couplers/adapters
▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape (Teflon) and masking tape
Learning Activity 7.1.1
Learning Activity Resources/Special Instructions/References
Prepare for pressure testing ▪ Information Sheet: 7.1.1 ▪ Self-Check Quiz: 7.1.1 ▪ Answer Key: 7.1.1 ▪ https://www.youtube.com/watch?v=9lqF9sRt_FM ▪ https://www.hunker.com/12218547/how-to-pressure-
test-plumbing
CBLM – Plumbing (Student Guide) v.1 Oct 2018 131
Skills for Employment Investment Programme (SEIP)
Information Sheet 7.1.1
Learning Objective: to confirm the work activities related to prepare for prepare for pressure testing in a
workplace.
Work activities: The following work activities must consider preparing for pressure testing in a workplace: ▪ Checking tightness of valves/fittings ▪ Measuring pipe runs ▪ Identifying piping run which are subject for pressure testing ▪ Identifying fittings to be isolated ▪ Isolating system components.
In other ways, the followings are need to be confirmed for preparation of pressure testing: ▪ Site visit/inspection: The requirement of site visit/inspection of a plumbing system to perform
pressure testing is important. ▪ Plumbing drawing/plan: Collect and study the plumbing drawing/plan to know about the whole
plumbing system. ▪ Tools and equipment gathering: Collect and gather required quantity of tools and equipment and
checked for usability. ▪ Materials gathering: Gather quality materials for problem solving. ▪ Plan out for pressure testing: Divide the plumbing system into sections and select spot for pressure
testing. ▪ Perform pressure testing: Piping system connections to be reviewed and checked for
tightness/integrity. ▪ Devices, fixture or components in the piping systems that needs to be isolated is shut off to avoid
damage. ▪ Determine maximum test pressure using proper tools and equipment and following the standard
method/procedure.
Plumbing drawing/plan:
Same as Information Sheet 2.1.1 – Interpret Drawings and Plumbing Plans (page 37 - 38)
Pressure testing method: ▪ Pressure tests are performed to ensure the safety, reliability, and leak tightness of pressure
systems. ▪ A pressure test is required for a new pressure system before use or an existing pressure system
after repair or alteration. ▪ Methods for pressure tests:
▪ Hydrostatic ▪ Pneumatic
▪ Hydrostatic testing is the most common method employed for testing pipes and pressure vessels. It is performed by using water as the test medium and pneumatic test uses air, nitrogen or any non-flammable and non- toxic gas.
▪ Hydrostatic testing is a process where components, such as piping or pressure vessels are tested for strength and leaks by filling the equipment with pressurized liquid.
▪ For pipelines, hydro tests are conducted while the pipeline is out of service. ▪ All oil and/or natural gas are typically vented off, and the line is mechanically cleaned prior to
testing. ▪ Hydrostatic testing works by completely filling the component with liquid (usually, but not always,
water), until a specific pressure is reached. ▪ The hydro test pressure often exceeds the designed working pressure of the equipment,
sometimes by over 150%, depending on the exact regulations and code requirements, as applicable.
▪ The pressure is then held for a specific amount of time to inspect visually for leaks. ▪ The visual inspection can be enhanced by applying either tracer or fluorescent dyes to the liquid
as suitable.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 132
Skills for Employment Investment Programme (SEIP)
▪ Hydrostatic testing is often required as a final proof test after repairs are completed and equipment is returned to service.
Self-Check Quiz 7.1.1
Write the correct answer for the following:
1. What are the methods of pressure testing?
2. What is the medium used for hydrostatic test?
3. What is the medium used for pneumatic test?
CBLM – Plumbing (Student Guide) v.1 Oct 2018 133
Skills for Employment Investment Programme (SEIP)
Learning Outcome 7.2- Gather Tools, Equipment and Materials
Contents:
▪ Names of personal protective equipment (PPE) and their uses: safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plugs
▪ List of main tools, equipment and materials uses ▪ Pressure testing tools, equipment and materials
Assessment criteria:
1. Required tools, equipment and materials are identified in accordance with plumbing plan and workplace procedure on pressure testing.
2. Pressure testing tools, equipment and materials are collected and checked for usability/accuracy. 3. Personal protective equipment (PPE) is gathered and strictly used.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), adjustable wrench, box wrench set, pipe wrench, mechanical pliers, screw driver (star, flat, positive)
▪ Equipment: pressure gauge, quick connects couplers/adapters, air compressor, water pump and nitrogen pump/tank
▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape (Teflon), masking tape
Learning Activity 7.2.1
Learning Activity Resources/Special Instructions/References
Gather tools, equipment and materials ▪ Information Sheets: 7.2.1, 7.2.2, 7.2.3, 7.2.4 ▪ Self-Check Quiz: 7.2.1 ▪ Answer Key: 7.2.1
Information Sheet 7.2.1
Learning Objective: to identify and uses of the personal protective equipment in the workplace.
Personal Protective Equipment (PPE):
Same as Information Sheet 1.1.1 – Gather and Check Tools, Equipment and Materials (page 8 - 9)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 134
Skills for Employment Investment Programme (SEIP)
Information Sheet 7.2.2
Learning Objective: to identify and uses of tools, equipment and materials in plumbing works.
Tools and equipment:
Same as Information Sheet 1.1.2 – Carry out steel pipe cutting operation (page 10 - 12)
Information Sheet 7.2.3
Learning Objective: to identify and uses of tools, equipment and materials in plumbing works.
Tools and equipment:
No. Picture Name and Used for
1
Pressure Gauge:
A pressure gauge is a mechanical instrument
designed to measure the internal pressure and/or
vacuum of a vessel or piping system.
2
Quick connect couplers/adapters:
Used to connect and disconnect lines fully pressurized
lines.
3
Air compressor:
An air compressor is a device that converts power into
potential energy stored in pressurized air.
4
Water pump:
A water pump uses a rotating impeller to move water
into the pump and pressurize the discharge flow.
5
Nitrogen pump/tank:
A high-pressure pump or compressor unit capable of
delivering high-purity nitrogen gas for use in oil or gas
wells.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 135
Skills for Employment Investment Programme (SEIP)
Self-Check Quiz 7.2.1
Identify the following picture and write their names and what they are used for:
No. Picture Used for
1
2
3
Information Sheet 7.2.4
Learning Objective: to identify, uses and check tools, equipment and materials in plumbing works.
Materials and pipes:
Same as Information Sheet 2.3.4 – Collect and Check Tools, Equipment and Materials (page 42 - 43)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 136
Skills for Employment Investment Programme (SEIP)
Learning Outcome 7.3 - Carryout Pressure Testing
Contents:
▪ Pressure testing method/procedure ▪ Leak testing method: soap solution, leak testing instrument ▪ Safety precaution
Assessment criteria:
1. Preliminary, intermediate and final test pressures are applied progressively into the system in accordance with workplace pressure testing plan/procedure.
2. Appropriate Leak testing method is applied for each applied pressure to determine presence of leaks.
3. Leak testing result is reported to the concern person.
4. Test results are recorded in accordance with workplace requirements.
5. Safety precaution is observed when performing pressure testing.
Resources required:
Students/trainees must be provided with the following resources:
▪ Personal protective equipment (PPE): safety helmet, safety shoes, hand gloves, safety glasses, safety belt, apron, dust mask, ear plug/guard
▪ Tools: measuring tape (5m), steel rule, callipers, adjustable wrench, box wrench set, pipe wrench, combination pliers, die stock, pipe cutter, pipe vice, hacksaw, screw driver (star, flat, positive), spirit level, pipe reamer, files (flat, half round, round)
▪ Equipment: pressure testing tools, equipment and materials
▪ Materials: coolant (water based), soft stone (marker), marking pen, pencil, solvent, thread tape (Teflon)
and masking tape
Learning Activity 7.3.1
Learning Activity Resources/Special Instructions/References
Carry out pressure
testing
▪ Information Sheet: 7.3.1 ▪ Self-Check Quiz: 7.3.1 ▪ Answer Key: 7.3.1 ▪ https://copperplumbing.org.uk/sites/default/files/content_attachments/pre
Information Sheet 7.3.1
Learning Objective: to carry out pressure testing in a workplace.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 137
Skills for Employment Investment Programme (SEIP)
Hydrostatic pressure testing:
▪ Hydrostatic Pressure Testing is a non-destructive testing (NDT) method of finding leaks or verifying
performance and durability in pressure vessels such as pipe, tubing, and coils. ▪ This is considered a non-destructive test and failures are rare, they can occur when the test piece
does not meet performance or durability specifications and may render the piece unusable. ▪ Pressure shall be raised gradually. ▪ An initial examination may be made at low pressure (say 10% of the specified test pressure). ▪ Pressure shall be gradually increased to a value 50% of the specified test pressure. ▪ Thereafter the pressure will be increased in stages of approximately 10% of the specified test
pressure until the test pressure is reached. ▪ Generally, 1.5 times of working pressure apply for testing. ▪ After the strength test pressure is reached, the pipework shall be isolated from the pressure source
and held for a minimum of 5 minutes. ▪ There shall be no appreciable drop in pressure during this time.
Leak: is a flow of liquid or gas through the wall of a vessel or pipe. Leaks require a pressure difference to generate the flow; they always flow from higher pressure to lower pressure.
Leak testing: ▪ There are a variety of leak testing techniques in use today. ▪ When considering an item requiring leak testing it is important to ascertain first whether detection
of the leak or measurement of the leakage rate is more important. ▪ The methods for leak testing are:
- Hydrostatic: by pressurizing liquid (water and dye) - Air pressure: by pressurizing air or gas into the system (soap solution-visual and sound)
▪ Leak detection:
The common feature of methods used to detect leaks is that they are almost always operator-
dependent, require strict supervision and are often very messy.
▪ Observation: Components are filled with pressurized gas and immersed in a liquid. Typically, they
are filled with air and immersed in water, but nitrogen under acetone is also used. The most
common observation technique is to look for a bubble stream.
▪ Leak location: Sometimes it critical to find out the location of the leak in the system.
▪ Leak measurement: It is important to measure the size of the leak and/or quantity of leakage in the system.
Safety Checklist
• In order to prevent accident from hydrostatic test operation, it demands to make good preparation prior to do the test, during the pressurization process and depressurizing operation.
• The job should be made in the form standard operating procedure.
Hydrostatic test preparation: 1. All test equipment and tools shall be inspected for wear and damage. 2. Pressure measurement tools are calibrated and their statuses of calibration are still valid. 3. Pressure gauges used in the test have enough capacity. The gauges are recommended to have
150% of the maximum allowable working pressure. 4. Pressure gauges must be installed at a proper location so that it can be easily read and do not
create additional hazards to the hydrostatic test. 5. Vents are available and installed the high points to vent air. Check the vent line before testing and
make sure it is not blocked. 6. Choose drain valve at the lowest point in order to completely empty the vessel and pipe. 7. The hydrostatic-pressurizing pump is completed with safety relief valve. 8. Wear proper personal protective equipment.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 138
Skills for Employment Investment Programme (SEIP)
Pressurization process: 1. Remove all air from the vessel and pipe line by water through vent line. 2. Pressurization is conducted gradually/slowly. 3. Mark all leak points and repair them before preceding the test. 4. Do not monitor during pressurization step directly from the front of sight glass or level glass.
De-pressurization process: 1. Start de-pressurization by opening gradually the vent valve. Do it slowly. 2. Do not open the drain valve if the vent valve if still closed. 3. Open the lowest drain point to completely remove water from the vessel and pipeline. 4. Ensure that no remaining pressure trapped inside the pipe line or vessel.
Just checking:
1. What is leak? 2. Why a safety check list is required before starting testing operation?
Self-Check Quiz 7.3.1
Read the statement carefully and justify whether it is ‘True’ or ‘False’.
No. Description True False
1. Hydrostatic Pressure Testing is a non-destructive testing (NDT) method of
finding leaks or verifying performance and durability in plumbing system.
2. A leak is a flow of liquid or gas through the wall of a vessel or pipe.
3. For the hydrostatic test, the gauges are recommended to have 100% of the
maximum allowable working pressure.
4. Pressurization is conducted gradually/slowly.
5. For the hydrostatic test, generally oil and dye used as pressurizing liquid.
CBLM – Plumbing (Student Guide) v.1 Oct 2018 139
Skills for Employment Investment Programme (SEIP)
Learning Outcome 7.4 - Clean and Maintain the Work Area
Same as Learning Outcome 1.5 – Clean and maintain the Work Area (page 29 - 32)
CBLM – Plumbing (Student Guide) v.1 Oct 2018 140
Skills for Employment Investment Programme (SEIP)
ANSWER KEYS
Answer Key 7.1.1
1. There are two methods for pressure tests: hydrostatic and pneumatic.
2. Water is use as medium of hydrostatic test.
3. Air, nitrogen or any non-flammable and non- toxic gas are use as medium of pneumatic test.
Answer Key 7.2.1
1. Pressure gauge: used to measure the internal pressure and/or vacuum of a vessel or piping system.
2. Quick connect couplers/adapters: used to connect and disconnect lines fully pressurised lines.
3. Water pump: used to move water into the pump and pressurize the discharge flow.
Answer Key 7.3.1
1. True 2. True 3. False 4. True 5. False