series 1 · 2006. 1. 12. · model numbers ac control a1210 a1225 a1240 a2410 a2425 a2450 a2475...
TRANSCRIPT
-
MODEL NUMBERS AC CONTROL A1210 A1225 A1240 A2410 A2425 A2450 A2475 A2490DC CONTROL D1210 D1225 D1240 D2410 D2425 D2450 D2475 D2490
OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 24-140 24-140 24-140 24-280 24-280 24-280 24-280 24-280
Max. Load Current ➂ [Arms] 10 25 40 10 25 50 75 90
Min. Load Current, [mArms] 40 40 40 40 40 40 40 40
Transient Overvoltage [Vpk] 400 400 400 600 600 600 600 600
Max. Surge Current, (16.6ms) [Apk] 120 250 625 120 250 625 1000 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
Thermal Resistance Junction to Case (RθJC) [˚C/W] 1.48 1.02 0.63 1.48 1.02 0.63 0.31 0.28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 60 260 1620 60 260 1620 4150 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 8 8 8 10 10 10 10 10
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁ 500 500 500 500 500 500 500 500
Max. Turn-On Time ➃ 1/2 Cycle (DC Control), 10.0 msec (AC Control)
Max. Turn-Off Time 1/2 Cycle (DC Control), 40.0 msec(AC Control)
Power Factor (Min.) with Max. Load 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
INPUT SPECIFICATIONS ➀ DC CONTROL AC CONTROL AC CONTROL ( E S U F F I X )
Control Voltage Range 3-32 Vdc 90-280 Vrms (60Hz) 18-36 Vrms
Max. Reverse Voltage -32 Vdc --- ---
Max. Turn-On Voltage 3.0 Vdc 90 Vrms 18 Vrms
Min. Turn-Off Voltage 1.0 Vdc 10 Vrms 4.0 Vrms
Nominal Input Impedance 1500 Ohms 60K Ohms 9.0K Ohms
Typical Input Current 3.4mA @ 5 Vdc, 20mA @ 28Vdc 2mA @ 120 Vrms, 4mA @ 240 Vrms 3mA @ 24 Vrms
GENERAL NOTES
➀ All parameters at 25˚ C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 3.➃ Turn-on time for random turn-on versions is 0.02 msec (DC Control Models).
• Zero Voltage and Random Turn-On Switching
• Panel Mount• 600V Transient Capability• Internal Snubber• 110 & 125A Models
Available
FastFax Document No. 151
SERIES1Rev. 102104PAGE 1 OF 3
Featuring state-of-the-art Surface Mount Technology, these SPST-NO relays deliver proven reliability in the most demanding applications. Output consists of an SCR AC switch and is available in zero-cross, random turn- on (phase controllable) and normally closed (Form B) versions with either AC or DC input (coil) control. Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Integrated Overvoltage Protection by AutomaticSelf Turn-On (Suffix P)
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 110-90Amp • 120/240 Vac - AC OUTPUT
-
Screw Torque Requirements:6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
Fastons:Single pair (up to 25A)Double pair* (up to 50A). *Caution: User must connect to both pairs
FastFax Document No.151
SERIES1Rev. 102104PAGE 2 OF 3
AVAILABLE OPTIONS-B Normally Closed (Form B)
Example: D2450-B, A2450-B
4D 400 Hz Operation 10-50 Amp Models Only Zero Cross Switching Only Example: 4D2450
E 24 Vac Input (18-36 Vac) Example: A2450E
-10 Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: D2450-10
F Faston Terminals (Up to 50A Models) Example: D1225F
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONS
Weight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
APPROVALS
UL E116949CSA LR81689VDE 10143 UG (Not Applicable: -B and 4D)
Crydom Heat Sinks offer excellentthermal management and are per-fectly matched to the load current rat-ings of Crydom panel mount relays.Request Crydom’s Heat Sink specifica-tion sheet for all the details.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
All dimensions are in inches (millimeters)
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
P Internal Overvoltage Protection. Relay Will Self Trigger Between 450-600 Vpk. Not Suitable For Capacitive Loads. Not Available with -B OptionAgencies Approval Pending. Example: D2425P
G Input Status LED.Agencies Approval PendingExample: D2450GNote: Control Voltage Range 4.5-32Vdc for DC Control Models.
1 2
4 3+--
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
Ordering System: Combination of the suffixes should be made in the following order: EFPG-10. Example: A2450EFPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached)Example: D2450H
Series 110-90Amp • 120/240 Vac - AC OUTPUT
-
12
8
4
02 4 8 106 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n110
115
120 Bas
e P
late
Tem
p [˚C
]
10A
9˚C/W 5˚C/W
3˚C/W7˚C/W
NO HEATSINK
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1˚C/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
.3˚C/W
CURRENT DERATING CURVES
FastFax Document No.151
SERIES1Rev. 102104 PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 110-90Amp • 120/240 Vac - AC OUTPUT
-
MODEL NUMBERS AC CONTROL A4812 A4825 A4850 A4875 A4890DC CONTROL D4812 D4825 D4850 D4875 D4890
OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 80-530 80-530 80-530 80-530 80-530
Max. Load Current ➂ [Arms] 12 25 50 75 90
Min. Load Current, [mArms] 40 40 40 40 40
Transient Overvoltage [Vpk] 800 800 800 800 800
Max. Surge Current, (16.6ms) [Apk] 140 250 625 1000 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.7 1.7 1.7 1.7 1.7
Thermal Resistance Junction to Case (RθJC) [˚C/W] 1.48 1.02 0.63 0.31 0.28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 81 260 1620 4150 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 10 10 10 10 10
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁ 500 500 500 500 500
Max. Turn-On Time 1/2 Cycle (DC Input), 10.0 msec (AC Input)
Max. Turn-Off Time 1/2 Cycle (DC Input), 40.0 msec (AC Input)
Power Factor (Min.) with Max. Load 0.5 0.5 0.5 0.5 0.5
INPUT SPECIFICATIONS ➀ DC CONTROL AC CONTROL ( D P R E F I X ) ( A P R E F I X )
Control Voltage Range 3-32 Vdc 90-280 Vrms (60Hz)
Max. Reverse Voltage -32 Vdc ---
Max. Turn-On Voltage 3.0 Vdc 90 Vrms
Min. Turn-Off Voltage 1.0 Vdc 10 Vrms
Nominal Input Impedance See Note 60K Ohms
Typical Input Current 2.0 mA 2mA @ 120 Vrms, 4mA @ 240 Vrms
G E N E R A L N O T E S
➀ All parameters at 25˚C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 2.➃
➄
Turn-on time for random turn-on versions is 0.02 msec (DC Control Models).Input circuitry incorporates active current limiter.
• Zero Voltage and Random Turn-On Switching • Panel Mount• 800V Transient Capability
FastFax Document No.SERIES A48/D48.Rev. 111003PAGE 1 OF 3
Featuring state-of-the-art Surface Mount Technology, these SPST-NO relays deliver proven reliability in the most demanding applications. Output consists of an SCR AC switch and is available in zero-cross, random turn-on (phase controllable) and ver- sions with either AC or DC input (coil) control. Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Internal Snubber
➃
➄
➄
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series A48, D4812-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
AVAILABLE OPTIONS
-10 Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: D4890-10
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
Crydom Heat Sinks offer excellentthermal management and are per- fectly matched to the load current ratings of Crydom panel mount relays. Request Crydom’s Heat Sink specification sheet for all the details.
FastFax Document No.SERIES A48/D48 Rev. 111003 PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.APPROVALSUL E116949CSA LR81689VDE 10143 UG
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
All dimensions are in inches (millimeters)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
F Faston Terminals (Up to 25 Amp Models) Example: D4850F
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
34
1 2
-- +
Fastons: Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect to both pairs
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached) Example: D4850H
Series A48, D4812-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
12
8
4
02 4 8 126 20 40 60 80
Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
110
115
120 Bas
e P
late
Tem
p [˚C
]
12A
9˚C/W 5˚C/W
3˚C/W7˚C/W
NO HEATSINK
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1ºC/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
.3˚C/W
2
6
10
14
0 10
C U R R E N T D E R A T I N G C U R V E S
FastFax Document No.SERIES A48/D48.Rev. 111003 PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series A48, D4812-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
AVAILABLE OPTIONS
-10 Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: D4890-10
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
Crydom Heat Sinks offer excellentthermal management and are per- fectly matched to the load current ratings of Crydom panel mount relays. Request Crydom’s Heat Sink specification sheet for all the details.
FastFax Document No.SERIES A48/D48 Rev. 111003 PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.APPROVALSUL E116949CSA LR81689VDE 10143 UG
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
All dimensions are in inches (millimeters)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
SOLID-STATE RELAY
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
F Faston Terminals (Up to 25 Amp Models) Example: D4850F
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
SOLID-STATE RELAY
34
1 2
-- +
Fastons: Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect to both pairs
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached) Example: D4850H
Series A48, D4812-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
12
8
4
02 4 8 126 20 40 60 80
Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
110
115
120 Bas
e P
late
Tem
p [˚C
]
12A
9˚C/W 5˚C/W
3˚C/W7˚C/W
NO HEATSINK
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1ºC/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
.3˚C/W
2
6
10
14
0 10
C U R R E N T D E R A T I N G C U R V E S
FastFax Document No.SERIES A48/D48.Rev. 111003 PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series A48, D4812-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
MODEL NUMBERS AC CONTROL HA4812 HA4825 HA4850 HA4875 HA4890DC CONTROL HD4812 HD4825 HD4850 HD4875 HD4890
OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 48-530 48-530 48-530 48-530 48-530
Max. Load Current ➂ [Arms] 12 25 50 75 90
Min. Load Current, [mArms] 40 40 40 40 40
Transient Overvoltage [Vpk] 1200 1200 1200 1200 1200
Max. Surge Current, (16.6ms) [Apk] 140 250 625 1000 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.7 1.7 1.7 1.7 1.7
Thermal Resistance Junction to Case (RθJC) [˚C/W] 1.48 1.02 0.63 0.31 0.28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 81 260 1620 4150 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 10 10 10 10 10
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁ 500 500 500 500 500
Max. Turn-On Time ➄ 1/2 Cycle (DC Input), 10.0 msec (AC Input)
Max. Turn-Off Time 1/2 Cycle (DC Input), 40.0 msec (AC Input)
Power Factor (Min.) with Max. Load 0.5 0.5 0.5 0.5 0.5
INPUT SPECIFICATIONS ➀ DC CONTROL AC CONTROL AC CONTROL ( D P R E F I X ) ( A P R E F I X )➃ ( E S U F F I X )
Control Voltage Range 3-32 Vdc 90-280 Vrms (60Hz) 18-36 Vrms
Max. Reverse Voltage -32 Vdc --- ---
Max. Turn-On Voltage 3.0 Vdc 90 Vrms 18 Vrms
Min. Turn-Off Voltage 1.0 Vdc 10 Vrms 4.0 Vrms
Nominal Input Impedance See Note ➅ 60K Ohms 9.0K Ohms
Typical Input Current 2.0 mA ➅ 2mA @ 120 Vrms, 4mA @ 240 Vrms 3mA @ 24 Vrms
G E N E R A L N O T E S➀ All parameters at 25˚C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 2.➃ 24 Vac Input option, E suffix.➄ Turn-on time for random turn-on versions
is 0.02 msec (DC Control Models).
➅ Input circuitry incorporates active current limiter.
• Zero Voltage and Random Turn-On Switching
• Panel Mount• 1200V Transient Capability
FastFax Document No. 158SERIES HA/HD. REV. 111303 PAGE 1 OF 3
Featuring state-of-the-art Surface Mount Technology, these SPST-NO relays deliver proven reliability in the most demanding applications. Output consists of an SCR AC switch and is available in zero-cross, random turn-on (phase controllable) and ver- sions with either AC or DC input (coil) control. Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Integrated Overvoltage Protection by AutomaticSelf Turn-On (Suffix P)
• 110 & 125A ModelsAvailable
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series HA, HD12-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
AVAILABLE OPTIONSE 24 VAC Input (18-36 Vac)
Example: HA4825E
-10 Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: HD4890-10
F Faston Terminals (Up to 50 Amp Models) Example: HD4850F
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
Crydom Heat Sinks offer excellentthermal management and are per- fectly matched to the load current ratings of Crydom panel mount relays. Request Crydom’s Heat Sink specification sheet for all the details.
FastFax Document No. 158SERIES HA/HD. REV. 111303PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.APPROVALSUL E116949CSA LR81689VDE 10143 UG
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
Fastons: Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect to both pairs
All dimensions are in inches (millimeters)
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
P Internal Overvoltage Protection. Relay Will Self Trigger Between 900-1200 Vpk. Not Suitable For Capacitive Loads. Agencies Approval Pending. Example: HD4825P
34
1 2
-- +
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
G Input Status LED.Agencies Approval PendingExample: HD4850GNote: Control Voltage Range 4.5-32 Vdc for DC Control Models.
Ordering System: Combination of the suffixes should be made in the following order: EFPG-10. Example: HA4850EFPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached) Example: HD4890H
Series HA, HD12-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
12
8
4
02 4 8 126 20 40 60 80
Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
110
115
120 Bas
e P
late
Tem
p [˚C
]
12A
9˚C/W 5˚C/W
3˚C/W7˚C/W
NO HEATSINK
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1ºC/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
.3˚C/W
2
6
10
14
0 10
C U R R E N T D E R A T I N G C U R V E S
FastFax Document No. 158SERIES HA/HD. REV. 111303PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series HA, HD12-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
MODEL NUMBERS AC CONTROL HA6025 HA6050 HA6090 HA60125DC CONTROL HD6025 HD6050 HD6090 HD60125
OUTPUT SPECIFICATIONS ➀Nominal Line Voltage (±10%) [Vrms] 600 600 600 600
Operating Voltage Range (47-63 Hz) [Vrms] 48-660 48-660 48-660 48-660
Max. Load Current ➂ [Arms] 25 50 90 125
Min. Load Current, [mArms] 40 40 40 150
Transient Overvoltage [Vpk] 1200 1200 1200 1200
Max. Surge Current, (16.6ms) [Apk] 250 625 1,200 1,750
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.7 1.7 1.7 1.7
Thermal Resistance Junction to Case (RθJC) [˚ C/W] 1.02 0.63 0.28 0.22
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 260 1,620 6,000 12,700
Max. Off-State Leakage Current @ Rated Voltage [mArms] ➆ 5 5 5 5
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁ 500 500 500 500
Max. Turn-On Time ➄ 1/2 Cycle (DC Input), 10.0 msec (AC Input)
Max. Turn-Off Time 1/2 Cycle (DC Input), 40.0 msec (AC Input)
Power Factor (Min.) with Max. Load 0.5 0.5 0.5 0.5
INPUT SPECIFICATIONS ➀ DC CONTROL AC CONTROL AC CONTROL ( D P R E F I X ) ( A P R E F I X ) ➃ ( E S U F F I X )
Control Voltage Range 3-32 Vdc 90-280 Vrms (60Hz) 18-36 Vrms
Max. Reverse Voltage -32 Vdc --- ---
Max. Turn-On Voltage 3.0 Vdc 90 Vrms 18 Vrms
Min. Turn-Off Voltage 1.0 Vdc 10 Vrms 4.0 Vrms
Nominal Input Impedance See Note ➅ 60K Ohms 9.0K Ohms
Typical Input Current 2.0 mA ➅ 2mA @ 120 Vrms, 4mA @ 240 Vrms 3mA @ 24 Vrms
G E N E R A L N O T E S➀ All parameters at 25˚C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 2.➃ 24 Vac Input option, E suffix.➄ Turn-on time for random turn-on versions is 0.02 msec (DC Control Models).➅ Input circuitry incorporates active current limiter.➆ No internal snubber.
• Zero Voltage and Random Turn-On Switching
• Panel Mount• 1200V Blocking Capability• 600Vac - the preferred
choice in Canada
FastFax Document No.159SERIES HA/HD60.Rev. 111303 PAGE 1 OF 3
Featuring state-of-the-art Surface Mount Technology, these SPST-NO relays deliver proven reliability in the most demanding applications. Output consists of an SCR AC switch and is available in zero-cross, random turn-on (phase controllable) and ver- sions with either AC or DC input (coil) control. Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Integrated Overvoltage Protection by Automatic Self Turn-On (Suffix P)
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series HA/HD6025-125Amp • 600 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
APPROVALS
UL E116950CSA LR81689VDE 10143 UG
Crydom Heat Sinks offer excellentthermal management and are per-fectly matched to the load currentratings of Crydom panel mountrelays. Request Crydom’s Heat Sinkspecification sheet for all the details.
FastFax Document No.159SERIES HA/HD60.Rev. 111303PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
Screw Torque Requirements:6-32 Screws - 10 in./lbs., 8-32 and 10-32 Screws - 20in./lbs. (Screws dry without grease.)
Fastons:Single pair (up to 25A)Double pair* (up to 50A). *Caution: User must connect to both pairs
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
1 2OUTPUT
4 3INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
All dimensions are in inches (millimeters)
AVAILABLE OPTIONSE 24 VAC Input (18-36 Vac)
Example: HA6025E
-10 Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: HD6090-10
F Faston Terminals (Up to 50 Amp Models) Example: HD6050F
P Internal Overvoltage Protection. Relay Will Self Trigger Between 900-1200 Vpk. Not Suitable For Capacitive Loads. Agencies Approval Pending. Example: HD6025P
G Input Status LED.Agencies Approval PendingExample: HD6050GNote: Control Voltage Range 4.5-32Vdc for DC Control Models.
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
Ordering System: Combination of the suffixes should be made in the following order: EFPG-10. Example: HA6050EFPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached) Example: HD6090H
Series HA/HD6025-125Amp • 600 Vac - AC OUTPUT
1 2
4 3
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
FastFax Document No.159SERIES HA/HD60.Rev. 111303 PAGE 3 OF 3
Bas
e P
late
Tem
p [˚C
]
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
50A
2˚C/W
.5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1˚C/W
.4˚C/W
90
.5˚C/W
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W100
110
3˚C/W
NO HEATSINK
2˚C/W
160
80
40
120
030 60 120 090 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
100
110
120
Bas
e P
late
Tem
p [˚C
]
125A
.5˚C/W
.4˚C/W90
1˚C/W
.2˚C/W
1˚C/W
.2˚C/W
C U R R E N T D E R A T I N G C U R V E S
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series HA/HD6025-125Amp • 600 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
MODEL NUMBERS DC CONTROL H12CD4850 H12CD4890
AC CONTROL H12CA4850 H12CA4890OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 48-660 48-660
Max. Load Current ➂ [Arms] 50 90
Min. Load Current, [mArms] 150 150
Transient Overvoltage [Vpk] 1200 1200
Max. Surge Current, (16.6ms) [Apk] 625 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6
Thermal Resistance Junction to Case (RθJC) [˚ C/W] .63 .28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 1620 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 1.0 1.0
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec]➁ 500 500
Max. Turn-On Time ➃ 1/2 Cycle (DC Control), 10.0 msec (AC Control)
Max. Turn-Off Time 1/2 Cycle (DC Control), 40.0 msec (AC Control)
Power Factor (Min.) with Max. Load 0.5 0.5
INPUT SPECIFICATIONS ➀ DC CONTROL AC CONTROL (H12CD PREFIX) (H12CA PREFIX)
Control Voltage Range 4-15 Vdc 90-140 Vrms
Max. Turn-On Voltage 4.0 Vdc 90 Vrms
Min. Turn-Off Voltage 1.0 Vdc 10.0 Vrms
Nominal Input Impedance 300 Ohms 8K Ohms
Typical Input Current 15 mA @ 5 Vdc 15 mA @ 120 Vrms
GENERAL NOTES
➀ All parameters at 25˚C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 2.➃ Turn-on time for DC control random turn-on versions is 0.02 msec.
• 1200 Volt Blocking• Panel Mount• Up to 660 Vac• Zero Voltage and Random
Turn-On• SCR Output
SERIES H12C.REV. 111203 PAGE 1 OF 3
High voltage relays use IC driven cir- cuits for switching loads up to 660 VAC. All models come with 1200 Volts blocking and are available with either AC or DC input (coil) control. Types H12CA and H12CD are snubberless (reduced leakage current). Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Integrated Overvoltage Protection by Automatic Self Turn-On (Suffix P)
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series H12C50-90Amp • 480 Vac • AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
APPROVALS
UL E116949CSA LR81689VDE 10143 UG
Crydom Heat Sinks offer excellent ther-mal management and are perfectlymatched to the load current ratings ofCrydom panel mount relays. RequestCrydom’s Heat Sink specification sheetfor all the details.
SERIES H12C. Rev. 111203 PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
Available Options
F Faston Terminals. (50 Amp Models Only) Example: H12CD4850F
-10 Random Turn-On. Example: H12CD4850-10
Screw Torque Requirements: *6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs.(Screws dry without grease.)
Fastons:Double pair* (50A model only). Caution: User must connect to both pairs
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
All dimensions are in inches (millimeters)
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
1 2
4 3-- +
Internal Overvoltage Protection.Relay Will Self Trigger Between900-1200Vpk. Not Suitable ForCapacitive Loads. Agencies Approval PendingExample: H12CD4850P
P
G Input Status LED.Agencies Approval PendingExample: H12CD4850GNote: Control Voltage Range 5.5-15Vdc for DC Control Models.
Ordering System: Combination of the suffixes should be made in the following order: FPG-10. Example: H12CD4850FPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached)Example: H12CD4850H
Series H12C50-90Amp • 480 Vac • AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
SERIES H12C. Rev. 111203 PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1˚C/W
.4˚C/W
.2˚C/W
90.5˚C/W
CURRENT DERATING CURVES
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series H12C50-90Amp • 480 Vac • AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
MODEL NUMBERS H12D4825 H12D4850 H12D4875 H12D4890
OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 48-530 48-530 48-530 48-530
Max. Load Current ➂ [Arms] 25 50 75 90
Min. Load Current, [mArms] 150 150 150 150
Transient Overvoltage [Vpk] 1200 1200 1200 1200
Max. Surge Current, (16.6ms) [Apk] 250 625 1000 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 1.6
Thermal Resistance Junction to Case (R JC) [˚C/W] 1.02 .63 .31 .28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 260 1620 4150 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 10 10 10 10
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] 500 500 500 500
Max. Turn-On Time 1/2 Cycle
Max. Turn-Off Time 1/2 Cycle
Power Factor (Min.) with Max. Load 0.5 0.5 0.5 0.5
INPUT SPECIFICATIONS
Control Voltage Range 4-32Vdc
Max. Turn-On Voltage 4.0 Vdc
Min. Turn-Off Voltage 1.0 Vdc
Nominal Input Impedance See Note 5
Typical Input Current 15 mA @ 5 Vdc
GENERAL NOTES
All parameters at 25˚ C unless otherwise specified.
Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
Heat sinking required, for derating curves see page 2.
Turn-on time for DC control random turn-on versions is 0.02 msec.
Input circuitry incorporates active current limiter.
• 1200 Volt Blocking• Panel Mount• Up to 530 Vac• Zero Voltage and Random
Turn-On• SCR Output
FastFax Document No.157SERIES H12D. Rev. 111203 PAGE 1 OF 3
High voltage relays use IC driven cir- cuits for switching loads up to 660 VAC. All models come with 1200 Volts blocking and are available with either AC or DC input (coil) control.
Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Integrated Overvoltage Protection by Automatic Self Turn-On (Suffix P)
1/2 Cycle
1/2 Cycle
1/2 Cycle
1/2 Cycle
1/2 Cycle
1/2 Cycle
➀➁➂➃➄
➀
➄
➃
➁
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series H12D25-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
APPROVALS
UL E116949CSA LR81689VDE 10143 UG
Crydom Heat Sinks offer excellent ther
-mal management and are perfectlymatched to the load current ratings ofCrydom panel mount relays. RequestCrydom’s Heat Sink specification sheetfor all the details.
SERIES H12D. Rev. 111203 PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
Available Options
F Faston Terminals. (Up to 50 Amp Models) Example: H12D4850F
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
Fastons: Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect to both pairs
All dimensions are in inches (millimeters)
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
1 2
4 3-- +
Internal Overvoltage Protection.Relay Will Self Trigger Between900-1200Vpk. Not Suitable ForCapacitive Loads. Agencies Approval Pending.Example: H12D4850P
P
G Input Status LED.Agencies Approval PendingExample: H12D4850GNote: Control Voltage Range 5.5-32 Vdc
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
Ordering System: Combination of the suffixes should be made in the following order:FPG-10. Example: H12D4850FPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
FastFax Document No.157
H Heat Transfer Pad (Attached)Example: H12D4850H
Series H12D25-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1˚C/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
.3˚C/W
CURRENT DERATING CURVES
SERIES H12D. Rev. 111203PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
FastFax Document No.157
Series H12D25-90Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
MODEL NUMBERS H12WD4875 H12WD4890
OUTPUT SPECIFICATIONS ➀
Operating Voltage (47-63 Hz) [Vrms] 48-660 48-660
Max. Load Current ➂ [Arms] 75 90
Min. Load Current, [mArms] 150 150
Transient Overvoltage [Vpk] 1200 1200
Max. Surge Current, (16.6ms) [Apk] 1000 1200
Max. On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6
Thermal Resistance Junction to Case (RθJC) [˚C/W] .31 .28
Maximum I 2 t for Fusing, (8.3 msec.) [A 2sec] 4150 6000
Max. Off-State Leakage Current @ Rated Voltage [mArms] 1.0 1.0
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁ 500 500
Max. Turn-On Time ➃
Max. Turn-Off Time
Power Factor (Min.) with Max. Load 0.5 0.5
INPUT SPECIFICATIONS ➀
Control Voltage Range 4-32 Vdc
Max. Turn-On Voltage 4.0 Vdc
Min. Turn-Off Voltage 1.0 Vdc
Nominal Input Impedance See Note 5
Typical Input Current 15 mA @ 5 Vdc
GENERAL NOTES
➀ All parameters at 25˚C unless otherwise specified.➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1➂ Heat sinking required, for derating curves see page 2.➃ Turn-on time for DC control random turn-on versions is 0.02 msec.➄ Input circuitry incorporates active current limiter.
• 1200 Volt Blocking
• Panel Mount
• Up to 660 Vac
• Zero Voltage and Random Turn-On
• SCR Output
SERIES H12WD. Rev. 111203 PAGE 1 OF 3
High voltage relays use IC driven cir- cuits for switching loads up to 660 VAC. All models come with 1200 Volts blocking. Type H12WD is a snubberless(reduced leakage current). Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
H12WD4825 H12WD4850
48-660 48-660
25 50
150 150
1200 1200
250 625
1.6 1.6
1.02 .63
260 1620
1.0 1.0
500 500
1/2 Cycle1/2 Cycle
0.5 0.5
➄
1/2 Cycle 1/2 Cycle
1/2 Cycle1/2 Cycle1/2 Cycle 1/2 Cycle
• Integrated Overvoltage Protection by Automatic Self Turn-On (Suffix P)
H12WD48125
48-660
125
150
1200
1750
1.7
.22
12700
1.0
500
0.5
1/2 Cycle
1/2 Cycle
➅ Compliant only.
➅
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series H12WD25-125Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
GENERAL SPECIFICATIONS
Dielectric Strength 50/60Hz Input/Output/Base 4000 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 8 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
APPROVALS
UL E116949CSA LR81689VDE 10143 UG
Crydom Heat Sinks offer excellent ther-mal management and are perfectlymatched to the load current ratings ofCrydom panel mount relays. RequestCrydom’s Heat Sink specification sheetfor all the details.
SERIES H12WD.Rev. 111203 PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
Available Options
F Faston Terminals. (Up to 50 Amp Models) Example: H12WD4850F
-10 Random Turn-On. Example: H12WD4850-10
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and 10-32 Screws - 20in. lbs. (Screws dry without grease.)
Fastons: Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect to both pairs
All dimensions are in inches (millimeters)
.90(22.9)
FASTON TERMINAL.187 X .032(2 PLCS.)
BASE PLATE.125 (3.2)
FASTON TERMINAL.250 X .032 (2 PLCS.)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.87 REF.(22.2)
OUTPUT
INPUT
1.00(25.4)1.80
(45.7)
.45(11.4)
1.10(27.9)MOUNTING
HOLE/SLOT0.17 (4.3) DIA.
1 2
4 3-- +
Internal Overvoltage Protection.Relay Will Self Trigger Between900-1200Vpk. Not Suitable ForCapacitive Loads. Agencies Approval Pending.Example: H12WD4850P
P
G Input Status LED.Agencies Approval PendingExample: H12WD4850GNote: Control Voltage Range 5.5-32 Vdc
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
1 2OUTPUT
34+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
BASE PLATE.125 (3.2)
Ordering System: Combination of the suffixes should be made in the following order:FPG-10. Example: H12WD4850FPG-10
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
H Heat Transfer Pad (Attached)Example: H12WD4850H
Series H12WD25-125Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
30
20
10
25
15
5
05 10 20 2515 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
Bas
e P
late
Tem
p [˚C
]
25A
1˚C/W
100
110
3˚C/W
NO HEATSINK
60
40
20
010 20 40 5030 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
Bas
e P
late
Tem
p [˚C
]
50A
2˚C/W
1˚C/W .5˚C/W
100
110
120
1.5˚C/W
NO HEATSINK
120
80
40
020 40 80 060 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
90A
1˚C/W
.4˚C/W
.2˚C/W
90.5˚C/W
2˚C/W
120
80
40
015 30 60 7545 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n 100
110
120
Bas
e P
late
Tem
p [˚C
]
75A
.5˚C/W95
1˚C/W
.3˚C/W
CURRENT DERATING CURVES
SERIES H12WD. Rev. 111203 PAGE 3 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
160
80
40
120
030 60 120 090 20 40 60 80Load Current [Arms] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
100
110
120
Bas
e P
late
Tem
p [˚C
]
125A
.5˚C/W
.4˚C/W90
1˚C/W
.2˚C/W
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series H12WD25-125Amp • 480 Vac - AC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
OUTPUT SPECIFICATIONS ➀
MODEL NUMBERS D1D07 D1D12 D1D20 D1D40 D2D07 D2D12 D4D07 D4D12 D5D07 D5D10
Operating Voltage Range [Vdc] 0-100 0-100 0-100 0-100 0-200 0-200 0-400 0-400 0-500 0-500
Max. Load Current ➂ [Adc] 7 12 20 40 7 12 7 12 7 10
Min. Load Current [mA] 20 20 20 20 20 20 20 20 20 20
Max. Surge Current, [Adc] (10Msec) 15 28 42 106 22 27 17 36 19 29
Max. On-State Voltage Drop @ Rated Current [Vdc] 2.0 1.6 2.1 2.1 2.0 2.8 4.2 4.2 5.7 5.5
Thermal Resistance Junction to Case [RθJC] C/W 2.2 1.34 1.06 0.83 1.5 1.06 1.06 0.8 1.0 0.8
Max On-state Resistance @ Rated Current (RDS-ON) [Ohms] .29 .13 .10 .05 .29 .23 .6 .35 .8 .55
Max. Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.2 0.3 0.3 0.1 0.3 0.3 0.3 0.2 0.3
Max. Turn-On Time [µsec] 100 100 100 100 100 100 100 100 100 100
Max. Turn-Off Time [msec] 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
INPUT SPECIFICATIONS ➀ DC CONTROL
Control Voltage Range 3.5-32 Vdc
Maximum Turn-On Voltage 3.5 Vdc
Minimum Turn-Off Voltage 1.0 Vdc
Nominal Input Impedance See Note 4
Maximum Input Current 1.6 mA (5 Vdc), 28 mA (32 Vdc) ➃
G E N E R A L N O T E S➀ All parameters at 25ºC unless otherwise specified.➁ Dielectric strength and insulation resistance are measured between input and output.➂ Heat sinking required, for derating curves see page 3.➃ Input circuitry incorporates active current limiter.
• MOSFET Output
• Low On-State Resistance
• Paralleling Capability forHigher Currents
• Panel Mount
FastFax Document No. 164SERIES 1DC.Rev. 111003PAGE 1 OF 3
DC output relays feature MOSFET technology for low on-state resistance,assuring easy paralleling and switchingcapabilities to 40 amps at 100 Vdc.Lower current models are also availableto 500 Vdc. All models come inCrydom's standard panel-mount package.
Manufactured in Crydom’s ISO 9001Certified facility for optimum productperformance and reliability.
©2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 1-DC7-40Amp • 0-500 Vdc - DC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
GENERAL SPECIFICATIONS
Dielectric Strength 60Hz 2500 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 50 pF
Ambient Operating Temperature Range -20 to 80ºC
Ambient Storage Temperature Range -20 to 125ºC
M ECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
All dimensions are in inches (millimeters)
APPROVALSUL E116950 (100 Volt Models Only)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
OUTPUT
+--
+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
1 2
34
M AXIM UM SURGE vs. DURATION
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
5
10
15
20
25
30
35
40
45
50
55
60
D5D07
D5D10
D4D12
D4D07
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
50
100
150
200
D1D40
SURGE DURATION (msec)
SURGE DURATION (msec)
MA
X.
SUR
GE
CU
RR
EN
T (
Am
ps)
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
5
10
15
20
25
30
35
40
45
50
55
60D1D20
D1D07 D2D07
D2D12
D1D12
SURGE DURATION (msec)
MA
X.
SUR
GE
CU
RR
EN
T (
Am
ps)
MA
X.
SUR
GE
CU
RR
EN
T (
Am
ps)
DCCONTROLSOURCE SSR
INPU
T
OU
TPUT
4 (–) 1 (–)
3 (+) 2 (+)
(–)
(+)
LOAD
Input and output polarity must be observed.Inductive loads must be diode suppressed.
Transient ProtectionAll loads are inductive, even ones that are not so labeled. Aninductive load will produce harmful transient voltages when itis turned off. The more perfect the switch, the larger the tran-sient voltages; the MOSFET output is so nearly an ideal switchthat the transient voltages produced by seemingly "non-induc-tive" loads can cause damage if not suppressed. Diodes should be fast recovery type with PIV rated greater than supply voltage.
Screw Torque Requirements: 6-32 Screws - 10 in. lbs., 8-32 and10-32 Screws - 20in. lbs. (Screws dry without grease.)
FastFax Document No. 164SERIES 1DC.Rev. 111003PAGE 2 OF 3
©2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 1-DC7-40Amp • 0-500 Vdc - DC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
Base
Pla
te T
emp
[ºC]
D1D07 - 7A
Base
Pla
te T
emp
[ºC]
24
16
8
20
12
4
02 4 108 126 20 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
Base
Pla
te T
emp
[ºC]
2 4 1086
D1D12 - 12A16
12
8
4
020 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
90
120
100
110
90
120
100
110
18
9
6
15
12
3
020 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
95
120
100
110
45
30
15
04 8 16 2012 20 40 60 80Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
100
110
120
Base
Pla
te T
emp
[ºC]
D1D20 - 20A80
90
90
60
30
08 16 32 4024 20 40 60 80Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
Base
Pla
te T
emp
[ºC]
D1D40 - 40A
120
80
100
140
D2D07 - 7A40
20
10
30
012
2 4 1086 12
20 40 60 80Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
Base
Pla
te T
emp
[ºC]
D2D12 - 12A
40
10
30
10
30
20
03 41 2 6 75 20 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
85
120
Base
Pla
te T
emp
[ºC]
3 41 2 6 75
3 41 2 6 75
3 41 2 6 75
D4D07 - 7A
100
110
85
120
100
110
85
120
100
110
85
120
100
110
60
40
50
10
20
30
020 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
Base
Pla
te T
emp
[ºC]
D4D12 - 12A40
20
020 40 60 80
Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on
Base
Pla
te T
emp
[ºC]
D5D07 - 7A
60
30
20
10
40
50
02 4 8 106 20 40 60 80Load Current [Adc] Max Ambient Temp. [ºC]
Pow
er D
issi
pati
on 90
105
120
Base
Pla
te T
emp
[ºC]
D5D10 - 10A75
6ºC/W
2ºC/W 1ºC/W
4ºC/W
NO HEATSINK
4ºC/W
1ºC/W
0.5ºC/W
2ºC/W
NO HEATSINK
6ºC/W
2ºC/W
4ºC/W
NO HEATSINK
4ºC/W
1ºC/W
0.5ºC/W
2ºC/W
NO HEATSINK
6ºC/W
2ºC/W
1ºC/W
4ºC/W
NO HEATSINK
6ºC/W
2ºC/W
1ºC/W
4ºC/W
NO HEATSINK
6ºC/W
2ºC/W
4ºC/W
NO HEATSINK
6ºC/W
2ºC/W
4ºC/W
NO HEATSINK
1ºC/W
6ºC/W
1ºC/W
4ºC/W
NO HEATSINK
2ºC/W
2ºC/W
NO HEATSINK
0.2ºC/W0.5ºC/W
1.5ºC/W
CURRENT DERATING CURVES
Crydom Heat Sinks offer excellentthermal management and are perfect-ly matched to the load current ratingsof Crydom panel mount relays.Request Crydom’s Heat Sink specifica-tion sheet for all the details.
FastFax Document No. 164SERIES 1DC.Rev. 111003PAGE 3 OF 3
©2003 CRYDOM CORP, Specifications subject to change without notice.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 1-DC7-40Amp • 0-500 Vdc - DC OUTPUT
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.comCourtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
-
OUTPUT SPECIFICATIONS ➀
MODEL NUMBERS D1D07L D1D12L D1D20L D1D40L D2D07L D2D12L D4D07L D4D12L D5D07L D5D10L
Operating Voltage Range [Vdc] 0-100 0-100 0-100 0-100 0-200 0-200 0-400 0-400 0-500 0-500
Max. Load Current ➂ [Adc] 7 12 20 40 7 12 7 12 7 10
Min. Load Current [mA] 20 20 20 20 20 20 20 20 20 20
Max. Surge Current, [Adc] (10msec) 15 28 42 106 22 27 17 36 19 29
Max. On-State Voltage Drop @ Rated Current [Vdc] 2.0 1.6 2.1 2.1 2.0 2.8 4.2 4.2 5.7 5.5
Thermal Resistance Junction to Case [RθJC]˚C/W 2.2 1.34 1.06 0.83 1.5 1.06 1.06 0.8 1.0 0.8
Max On-state Resistance @ Rated Current (RDS-ON ) [Ohms] .29 .13 .10 .05 .29 .23 .6 .35 .8 .55
Max. Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.2 0.3 0.3 0.1 0.3 0.3 0.3 0.2 0.3
Max. Turn-On Time [msec] 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Max. Turn-Off Time [msec] 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
INPUT SPECIFICATIONS ➀ DC CONTROL
Control Voltage Range 3.5-32 Vdc
Maximum Turn-On Voltage 3.5 Vdc
Minimum Turn-Off Voltage 1.0 Vdc
Nominal Input Impedance See Note 4
Typical Input Current 20mA ➃
G E N E R A L N O T E S➀ All parameters at 25˚C unless otherwise specified.➁ Dielectric strength and insulation resistance are measured between input and output.➂ Heat sinking required, for derating curves see page 3.➃ Input circuitry incorporates active current limiter.
• MOSFET Output• Low On-State Resistance• Paralleling Capability for
Higher Currents• Panel Mount
FastFax Document No. SERIES 1DCL.Rev. 102704PAGE 1 OF 3
DC output relays feature MOSFET tech- nology for low on-state resistance, assuring easy paralleling and switching capabilities to 40 amps at 100 Vdc. Lower current models are also available to 500 Vdc. All models come in Crydom's standard panel-mount package. Manufactured in Crydom’s ISO 9001 Certified facility for optimum product performance and reliability.
© 2003 CRYDOM CORP, Specifications subject to change without notice.
• Optically Coupled
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 1-DCL7-40Amp • 0-500 Vdc - DC OUTPUT
-
GENERAL SPECIFICATIONS
Dielectric Strength 60Hz 2500 Vrms
Insulation Resistance (Min.) @ 500 Vdc 109 Ohm
Max. Capacitance Input/Output 50 pF
Ambient Operating Temperature Range -40 to 80˚C
Ambient Storage Temperature Range -40 to 125˚C
MECHANICAL SPECIFICATIONSWeight: (typical) 3.0 oz. (86.5g)
Encapsulation: Thermally Conductive Epoxy
Terminals: Screws and Saddle Clamps Furnished, Unmounted
All dimensions are in inches (millimeters)
APPROVALSUL E116950 (100 Volt Models Only)
1.87(47.5)
.78(19.8)
2.30(58.4)
1.70(43.2)
.90(22.9)
.45(11.4)
1.10(27.9)
8-32 TERMINAL(2 PLACES )
1.00(25.4) 6-32 TERMINAL
(2 PLACES)1.80(45.7)
OUTPUT
+--
+--
INPUT
MOUNTING HOLE/SLOT0.17 (4.3) DIA.
1 2
34
MAXIMUM SURGE vs. DURATION
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
5
10
15
20
25
30
35
40
45
50
55
60
D5D07
D5D10
D4D12
D4D07
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
50
100
150
200
D1D40
SURGE DURATION (msec)
SURGE DURATION (msec)
MA
X.
SU
RG
E C
UR
RE
NT
(A
mp
s)
2 3 4 5 68 10 2 3 4 5 68102 2 3 4 5 68103 2 3 4 5 68104
5
10
15
20
25
30
35
40
45
50
55
60D1D20
D1D07 D2D07
D2D12
D1D12
SURGE DURATION (msec)
MA
X.
SU
RG
E C
UR
RE
NT
(A
mp
s)M
AX
. S
UR
GE
CU
RR
EN
T (
Am
ps)
Screw Torque Requirements:6-32 Screws - 10 in. lbs., 8-32 and10-32 Screws - 20in. lbs. (Screws dry without grease.)
FastFax Document No. SERIES 1DCL.Rev. 102704PAGE 2 OF 3
© 2003 CRYDOM CORP, Specifications subject to change without notice.
DCCONTROLSOURCE SSR
INP
UT
OU
TP
UT
4 (–) 1 (–)
3 (+) 2 (+)
(–)
(+)
LOAD
Input and output polarity must be observed.Inductive loads must be diode suppressed.
Transient ProtectionAll loads are inductive, even ones that are not so labeled. Aninductive load will produce harmful transient voltages when itis turned off. The more perfect the switch, the larger the tran-sient voltages; the MOSFET output is so nearly an ideal switchthat the transient voltages produced by seemingly "non-induc-tive" loads can cause damage if not suppressed. Diodes should be fast recovery type with PIV rated greater than supply voltage.
For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154Email: [email protected] WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [email protected]. GERMANY: +49 (0)180 3000 506
Series 1-DCL7-40Amp • 0-500 Vdc - DC OUTPUT
-
Bas
e P
late
Tem
p [˚C
]
D1D07 - 7A
Bas
e P
late
Tem
p [˚C
]
24
16
8
20
12
4
02 4 108 126 20 40 60 80
Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
Bas
e P
late
Tem
p [˚C
]
2 4 1086
D1D12 - 12A16
12
8
4
020 40 60 80
Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
90
120
100
110
90
120
100
110
18
9
6
15
12
3
020 40 60 80
Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
95
120
100
110
45
30
15
04 8 16 2012 20 40 60 80Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
100
110
120
Bas
e P
late
Tem
p [˚C
]
D1D20 - 20A80
90
90
60
30
08 16 32 4024 20 40 60 80Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
Bas
e P
late
Tem
p [˚C
]
D1D40 - 40A
120
80
100
140
D2D07 - 7A40
20
10
30
012
2 4 1086 12
20 40 60 80Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
Bas
e P
late
Tem
p [˚C
]
D2D12 - 12A
40
10
30
10
30
20
03 41 2 6 75 20 40 60 80
Load Current [Adc] Max Ambient Temp. [̊ C]
Pow
er D
issi
patio
n
85
120
Bas
e P
late
Tem
p [˚C
]
3 41 2 6 75
3 41 2 6 75
3 41 2 6 75
D4D07 - 7A
100
110
85
120
100
110
85
120
100
110
85
120
100
110
60
40
50
10
20
30
020