OWNER'S MANUALSEG101

Stereo Phonograph System with USB,SD and PLL Radio

CAUTION

TO PREVENT FIRE OR SHOCK HAZARD,DO NOT USE THIS PLUG WITH

ANEXTENSION CORD,RECEP TACLE OR OTHER OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.TO PREVENT FIRE OR

SHOCK HAZARD,DONOT EXPOSE THISAPPLINACE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

1.) Read these instructions.

2.) Keep these instructions.

3.) Heed all warnings.

4.) Follow all warnings.

5.) Do not use this apparatus near water.

6.) Clean only with dry cloth.

7.) Do not block any ventilation openings.Install in accordance with the manufacturer's

instructions.

8.) Do not install near any heat sources such as radiators,heat registers,stoves,or other

apparatus (including amplifiers)that produce heat.

9.) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades

and a third grounding prong.The wide blade or the third prong is provided for your

safety.if the provided plug does not fit into you outlet,consult an electrician for

replacement of the obsolete outlet.

10.) Protect the power cord from being walked on or pinched particularly at

plugs,convenience receptacles,and point where they exit from the apparatus.

11.) Only use attachments / accessories specified by the manufacturer.

12.) Unplug this apparatus during lightning storms or when unused for long periods of

time

13.) Refer all servicing to qualified service personnel.Servicing is required when the

apparatus has been damaged in any way,such as power-supply cord or plug is

damaged,liquid has been spilled or objects have fallen into the apparatus,the apparatus

has been exposed to rain or moisture,does not operate normally,or has been dropped.

14.) This appliance shall not be exposed to dripping or splashing water and no object

filled with liquids such as vases shall be placed on the apparatus.

15.) Do not overload wall outlet.Use only power source as indicated.

16.) Use replacement parts as specified by the manufacturer.

17.) The product may be mounted to a wall only if recommended by the manufacturer.

18.) Upon completion of any service or repairs to this product,ask the service technician

to perform safety checks.

PREPARATION FOR USE

UNPACKING AND SET UP

·Carefully remove the unit from the display carton and remove all packing

material from the unit.

·Unwind the DC power plug and extend it to its full length.

·Unwind the FM Antenna wire and extend it to its full length.

·Unwind the speakers and extend it to its full length(open the speakers

fastener(L/R)

·Place the unit on a stable,level surface,convenient to an AC outlet,out of

Direct sunlight,and away from sources of excess heat,dust,moisture,

humidity,or strong magnetic fields.

·Connect the plug to your AC outlet.

·Raise the lid to expose the phonograph.The phonograph has been secured

For shipment with a transit screw.Use a coin or screwdriver to turn the transit

screw clockwise.This will allow the turntable to"float"

·Remove the opaque white plastic stylus

Cover from the phonograph stylus by

Sliding it in the direction of the arrow.

Discard the stylus cover.

·Remove the twist-tie that was used to

secure the tone arm during shipment.

·Release the tone arm lock lever.

·Connect the plug to your AC Outlet.

POWER SOURCE

This system is used dc adaptor operate on normal 240V 50HZ DC only.

Attempting to operate from any other power source may cause damage to the

system,and such damage is not covered by your warranty.

NOTE:If this plug will not fit into your outlet,you probably have an out-dated

Non-polarized AC outlet.You should have you outlet changed by a qualified

Please pull the power plug during shock and unused for a long time.

The power plug and power jack should be matched as a suitable make and

Break device,in order to make operation conveniently.

IMPORTANT:Raising And Lowering The Lid

To open the lid,raise it as far as it will go until the lid support bracket"locks"in

The open position. To close the lid,lift it upward slightly until the lid support

TO AVOID DAMAGING THE CABINET OR THE LID,NEVER FORCE THE LID CLOSED.

ALWAYS RAISE THE LID TO RELEASE THE LID SUPPORT BRACKET.

PROTECT YOUR FURNITURE

This model is equipped with non-skid rubber "feet" to prevent the product from

Moving when you operate the controls. These "feet" are made from non-migrating

Rubber material specially formulated to avoid leaving any marks or stains on

Your furniture. However certain types of oil based furniture polishes,wood

preservatives, or cleaning sprays may cause the rubber "feet" to soften,and

Leave marks or a rubber residue on the furniture. To prevent any damage to your

Furniture we strongly recommend that you purchase small self-adhesive felt

Pads, available at hardware stores and home improvement centres everywhere,

And apply these pads to the bottom of the rubber "feet" before you place the

Product on fine wooden furniture.

LOCATION OF CONTROLS AND INDICATORS

FRONT PANEL

1.) Phonograph Lid. 15.) PRESET/FOLDER-button

2.) Turntable. 16.) PROGRAM button

3.) Speakers 17.) ID3 button

4.) STOP button 18.) EQ button

5.) LCD display 19.) REPEAT button

6.) FM MODE button 20.) PRESET/FOLDER+ button

7.) VOLUME-button 21.) TUNING/SKIP+ button

8.) FUNCTION button 22.) RECORD button

9.) VOLUME+ button 23.) SD CARD slot

10.) PLAY/PAUSE button 24.) USB port

11.) POWER switch

12.) Tone Arm

13.) TUNING/BAND button

14.) TUNING/SKIP-button

BACK PANEL

25.) FM antenna

26.) AUX IN Jack

27.) LINE OUT Jack (R/L)

28.) AC power cord

REMOTE CONTROL OPERATION:

R1) PROGRAM.

R2) RECORD.

R3) REPEAT.

R4) PLAY/PAUSE.

R5) DN/FB(SKIP REV.).

R6) UP/FF(SKIP Forward.).

R7) STOP.

R8) TRACK-10.

R9) TRACK+10.

R10) RANDOM.

NOTE:All of the buttons on the remote control

have the same function as these buttons in the

unit.This remote control just used for CD/MP3,USB

mode.

PHONOGRAPH

1.) Turntable.

2.) 45 RPM Adapter.

3.) Transit Screw.

4.) Cue Lever.

5.) Speed Selector

(33&45&78 RPM).

6.) Tone Arm Lock.

7.) Tone Arm with Stylus.

BASIC FUNCTION

Switching on the unit

Note: Before switching on the unit,Please make sure that all connections have

Been got ready.

Press the POWER button the LCD display will illuminate and show HELLO

moving.Press FUNCTION button to select playing mode [USB/CARD/AUX/

TUNER/PHONO].

To adjust volume

Hold the electronic VOLUME UP/DOWN control to increase or decrease volume.

Built-in Different Equalizer System

This unit has a built-in equalizer system,Preset EQ button while playing to select different

music style (sound tone): FLAT, CLASSIC, ROCK, POP and JAZZ.

ID3 SYSTEM

When plays a USB or SD or AUX, Press the ID3 button,if the track file is write in

"ID3" it will automatically to search the information of "FOLDER NAME"

"ARTIST NAME" and "TITLE NAME" to show in the display. And press the ID3

Button again,the display will show "ID3 OFF" and change to normal.

RADIO OPERATION

TUNING IN RADIO STATIONS

1. Press the FUNCTION button to select TUNER mode,the display will show

"TUNER".

2. Press the BAND button to select the desired wave band: AM/FM. In FM

Position,press the FM mode button to select the FM MONO/FM ST.mode.

3. Tune to desired station by pressing the FF/UP or FM/DN, the display will

Show the band frequency.

4. Press the VOLUME+ or VOLUME-control to desired volume level.

5. Extend FM ANTENNA to its full length if you are listening to FM broadcasting.

Gently rock the unit back and forth to get the best reception when you are

Listening to AM program, or place the unit in an open location.

Note: When you are receiving FM stereo program, the display will show

"((((ST))))".

6. To turn off the radio, press the FUNCTION button to enter USB or CARD or

AUX or PHONO operation, or switch off the unit by pressing POWER

Stations.

RADIO AUTO SCAN (SEARCH)

Rotate the FF/UP or FB/DN control for 1 or 2 seconds, the unit will auto scan

Until having found a strong signal program, rotate and hold again to search other

Stations.

RADIO STATION MEMORY OPERATION

You may pre-store 40 (AM and FM) radio stations in memory for your

Preference controlled by remote handset, so as you can listen to your desired

Station directly and quickly, no need to tuning and search for again.

NOTE: you may pre-store 40 (10 for AM and 30 for FM) radio stations in

Memory for your preference controlled by remote handset.

1.Press the FUNCTION button to Set the unit to TUNER mode.

2.Press PROGRAM button to select band (AM or FM), Tune into a station.

3.Press PROGRAM button,"MEMORY"shows on the display. Then press the

M+/FOLDER+button to select the first storing location(fig2).

4.Press PROGRAM button again to store.

5.Search another station, repeat steps (3) & (4) until all desired stations stored.

Up to 40 stations can be programmed (10 for AM and 30 for FM).

6.Press M+/FOLDER+button to listen to the stored station directly.

USB PLAYBACK

1.Press the FUNCTION button to select USB mode.

2.Connect the USB Flash Disk Device into the USB PORT.

3.If the USB is readable,the display will show USB and The total number of

Tracks after several seconds.

4.Press the PLAY/PAUSE button to start playback, the display will show as the

fig 3.

5.Press the STOP button to stop playing.The display will show total number of

Tracks (fig4).

CAUTION:

·Do not use any USB extension cable for connecting the USB stick which may

Cause harmful interference

·In case of malfunction due to electrostatic discharge, just reset the product

(reconnect of power source may be required) to resume normal operation.

SD/MMC CARD INSTALLATION AND REMOVE

Press the card towards the SD/MMC CARD slot, when the installation is well

Done, a "click" sound will be heard. To remove the SD/MMC card,press the

Card gently the card will flick out. Now you can remove the card out of the card

Slot.

SD/MMC CARD PLAYBACK

1.Press the FUNCTION button to select CARD mode.

2.Connect the SD card to the SD CARD INPUT slot.The LCD will display total

Number of tracks stored inside the card (fig5).

3.Press the PLAY/PAUSE button to start playing. Press the PLAY/PAUSE button

Once again to temporarily stop.The track number will flash.

4.Press the STOP button to stop playing.THE display will show total number of

Tracks.

5.Proceed repeat play (repeat 1/repeat folder/repeat all)/program play/skip up

And down operation follow the steps described in above "USING THE

CARD/MP3".

SELECTING A DESIRED TRACK/PASSAGE

To select a desired track

·Press the FF/UP or FB/DN button repeatedly in stop mode or during playing

Until the desired track appears on the display.

·Press PLAY/PAUSE button to start play.

To search for a particular passage during playback (track scanning at

High speed)

Press and hold FF/UP or FB/DN button to scan the current playing track at

High speed until desired point (passage), then release the button, playback

Will start again from this point.

PROGRAM TRACKS

Program tracks of USB/SD are possible when playback is stopped. Up to 99

Tracks can be stored in the memory in any order.

1.In stop mode, press PROGRAM button to enter program setting, the "PROG"

Will show and the "F00 PO1"will show on the display (fig6).

2.Press M+/FOLDER+ to select the FOLDER,then press the FF/UP or FB/DN

Button to select the first desired track to be programmed.

3.Press PROGRAM button to enter. The display changes to show "F01 P02"

(fig7).

4.Repeat steps 1,2 & 3 to store other desired tracks until all tracks

Programmed.

5.Press PLAY/PAUSE button to start playback in the order you programmed.

6.Press STOP button to stop program playback.

NOTE:

You can press STOP button when the disc stopped to clear the memory.

REPEAT PLAY

You can play one track or all tracks on the disc repeatedly.

To Repeat a Single Track

1.Press REPEAT button once in play, The REPEAT 1 symbol will steady on.

The current track will be played over and over again till you press STOP

Button (fig8).

2.To cancel repeat play, press REPEAT button until the "REPEAT 1symbol"

goes off.

To repeat all the Tracks

1.Press REPEAT three time in play,The "REPEAT ALL" will be steady on. All

tracks on the disc will be played over and over again till you press STOP

Button (fig9).

2.To cancel repeat play, press REPEAT button until the "REPEAT ALL" goes

off.

To repeat current Directory

1.Press REPEAT button twice in play mode, "REPEAT FOLDER" shows steady

on the display, The current directory will be played repeatedly until the STOP

Button is pressed (fig10).

2.Press the REPEAT button until the "REPEAT FOLDER" disappear to cancel.

Note:

1.Repeat function also can be done in stop mode.

2.Repeat current directory must be with folder in your USB or SD CARD.

PHONO PLAY BACK

This system includes a full-size, 3-speed, belt-drive turntable. You can play 33,

45, and 78 RPM records.

1.) Press the VOLUME+ or VOLUME- control to a low level.

2.) Press the FUNCTION button to select(AUX/USB/CARD/TUNER/PHONO)

To the PHONO position, the display shows "PHONO"

3.) Make sure that you have removed the stylus cover from the stylus and

Have released the Tone Arm Lock that secured the tone arm to the tone

arm rest.

4.) Set the turntable Speed Selector to the appropriate speed, 33, 45, or 78

RPM. If you are playing 45 RPM singles, place the 45 RPM adapter on

The centre spindle.

5.) Place your record on the centre spindle.

6.) Raise the CUE lever to lift the tone arm off its rest. Move the tone arm to

The edge of the record. The turntable starts automatically. Use the CUE

Lever to gently lower the tone arm onto the record.

7.) Adjust the VOLUME+/- control to the desired level.

8.) When the tone arm reaches the end of the record it automatically returns to

The tone arm rest and the record player stops.

9.) To turn the system "off", press the POWER switch

NOTE:Do not turn or stop the turntable manually. Moving or jarring the

Turntable without securing the Tone Arm clamp could result in damage to the

Tone Arm.

IMPORTANT!!

·TO PROTECT THE TURNTABLE FROM DAMAGE DURING TRANSPORTATION, A

SILVER TRANSIT SCREW IS LOCATED AT THE UPPER RIGHT OF THE

TURNTABLE PLATFORM.

·BEFORE PLAYING, PLEASE USE A SCREWDRIVER TO

TURN THE TRANSIT SCREW IN CLOCKWISE DIRECTION

(SCREW GOING DOWN) COMPLETELY TO UNLOCK THE

TURNTABLE.

·TO LOCK THE TURNTABLE AGAING FOR TRANSPORTATION,

PLEASE TURN THE SCREW IN COUNTER-CLOCKWISE

DIRECTION.

·REMOVE THE ROUND PAPER CARD ON THE TURNTABLE

BEFORE PUTTING YOUR RECORD ON THE CENTER

SPINDLE.

AUX IN RECORDING

1.) Press the VOLUME+ or VOLUME-control to set the volume to a low level.

2.)Press the function button (AUX/USB/SD/TUNER/PHONO) to AUX

Position, insert the AUX line into the AUX in jack.

3.) Press FF/UP or FB/DN button to choose record the desired track.

4.) Plug U Disk into USB port or insert the SD CARD into the SD CARD slot, the

"USB" or "CARD" indicator will show on the display, press RECORD button

Once to enter into Record mode, "REC" indicator goes on. Press RECORD

Button twice will start to record the playing track into USB, the track will be re-

Start play from the beginning of the selected track. "REC" indicator flashes.

5.) Press STOP button will cancel the record function. Press STOP button

Once will stop RECORD mode, and "REC" indicator goes "Off", press

Twice will stop CD playing.

NOTE:When the player Playback AUX, the display will show "AUX"

PROGRAM RECORDING

This feature allows you choose the desired tracks to be recorded at one

time.

1.) Program tracks you want to record, procedures are the same as those of

Program playback step 1-4 on page 8, 9 Program indicator remains

"On".

2.) Press FF/UP or FB/DN control to choose the desired on in the

Programmed tracks.

3.) Plug U Disc into USB port or insert the SD CARD into the SD CARD slot.

Press PLAY/PAUSE button to begin play the programmed tracks,press

RECORD button twice to start record. "REC" indicator flashes. The

Display will show the playing track number, "AUX" and folder name of the

Track selected. For example:"001" AUX "f01".

4.) Press STOP button once will cancel the record function and " REC"

Indicator goes "Off", Otherwise the recording will be from the first track

To the end of the programmed tracks.

5.) After the last track has been recorded, the player stops and the display

Shows the total number. The program sequence has been canceled in

the memory. The PROG . Indicator goes "Off".

PHONO RECORDING

1.) Press the VOLUME+ or VOLUME- to set the volume to a low level.

2.) Press the function button(AUX/USB/SD/TUNER/PHONO) to PHONO

Position."PHONO" will be shown on the display.

3.) Plug U Disk into USB socket or insert the SD CARD into the SD CARD

slot. Place the record on the turntable center and play the record. Press

RECORD button twice to enter into record mode.The player will re-start

Play the first point of the track to be selected. "REC" will be shown on the

display and "REC" indicator remain flash. The recording will be from the

First to the end of the phono record.

4.) Press STOP button once will stoop RECORD mode, and "REC" indicator

Goes "Off" . "PHONO" will be shown on the display and phono record will

Continue to playback.

5.) Press the POWER switch to turn off the system.

NOTE: You may refer to playback of USB to play the recorded tracks in

USB.

AUX IN OPERATION

Insert the audio cable (not included) into the matching"AUX IN" socket of

The unit(TR-W188),opera te A as usual and through the speaker of TR-W188,

We can hear the sound exported from A.

LINE OUT OPERATION

This system includes a set of LINE OUT sockets (L/R) which allow you to record

From the Radio or phonograph of this system to an external recording device

Such as a cassette recorder. Mini-Disc,etc. In any play mode, insert the audio

Cable (not include) into the matching "LINE OUT " socket of the unit, operate

TR-W188 as usual , and through the speakers of B, you can hear the sound

Exported from TR-W188.