section 06 0003 - certified finish carpentry part 1 - …certified finish carpentry 06 0003 - 1 smha...

CERTIFIED FINISH CARPENTRY 06 0003 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 06 0003 - CERTIFIED FINISH CARPENTRY

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This section includes the following: 1. Wood lattice.

B. Lumber grading agencies, and the abbreviations used to reference them, include the following:

1. NELMA - Northeastern Lumber Manufacturers Association. 2. NLGA - National Lumber Grades Authority. 3. RIS - Redwood Inspection Service. 4. SPIB - Southern Pine Inspection Bureau. 5. WCLIB - West Coast Lumber Inspection Bureau. 6. WWPA - Western Wood Products Association.

1.3 SUBMITTALS

A. Product Data: For each type of process and factory-fabricated product. Indicate component materials and dimensions and include construction and application details.

1. Include data for wood-preservative treatment from chemical treatment manufacturer and certification by treating plant that treated materials comply with requirements. Indicate type of preservative used, net amount of preservative retained, and chemical treatment manufacturer's written instructions for handling, storing, installing, and finishing treated material.

2. For products receiving a waterborne treatment, include statement that moisture content of treated materials was reduced to levels specified before shipment to Project site.

3. Include copies of warranties from chemical treatment manufacturers for each type of treatment.

B. Research/Evaluation Reports: For the following, showing compliance with building code in effect for Project:

1. Preservative-treated wood. 2. Power-driven fasteners. 3. Powder-actuated fasteners.


1.4 DELIVERY, STORAGE, AND HANDLING

A. Stack lumber, plywood, and other panels; place spacers between each bundle to provide air circulation. Provide for air circulation around stacks and under coverings.

PART 2 - PRODUCTS

2.1 WOOD PRODUCTS, GENERAL

A. Lumber: DOC PS 20 and applicable rules of lumber grading agencies certified by the American Lumber Standards Committee Board of Review.

1. Factory mark each piece of lumber with grade stamp of grading agency. 2. Where nominal sizes are indicated, provide actual sizes required by DOC PS 20 for

moisture content specified. Where actual sizes are indicated, they are minimum dressed sizes for dry lumber.

3. Provide dressed lumber, S4S, unless otherwise indicated. 4. Actual Thickness (Inches): 0.5 5. Actual Width (Inches): 48 6. Actual Height (Feet): 4 7. Grid Opening (Inches): 2-3/4-in

2.2 WOOD-PRESERVATIVE-TREATED MATERIALS

A. Preservative Treatment by Pressure Process: AWPA C2 (lumber) and AWPA C9 (plywood), except that lumber that is not in contact with the ground and is continuously protected from liquid water may be treated according to AWPA C31 with inorganic boron (SBX).

1. Preservative Chemicals: Acceptable to authorities having jurisdiction and the following:

a. Preservative chemicals containing no arsenic or chromium. b. Use treatment that does not promote corrosion of metal fasteners.

B. Kiln-dry material after treatment to a maximum moisture content of 19 percent for lumber and 15 percent for plywood. Do not use material that is warped or does not comply with requirements for untreated material.

C. Mark each treated item with the treatment quality mark of an inspection agency approved by the American Lumber Standards Committee Board of Review.

D. Application: Treat items indicated on Drawings, and the following:

1. Exterior wood cants, nailers, curbs, equipment support bases, blocking, stripping, and similar members in connection with flashing, vapor barriers, and waterproofing.

2. Wood sills, sleepers, blocking, furring, stripping, and similar concealed members in contact with masonry or concrete.

3. Wood blocking, framing, sheathing and similar members in contact with curtain wall system.


4. Wood framing members less than 18 inches above grade. 5. Wood floor plates that are installed over concrete slabs directly in contact with earth.

2.3 MISCELLANEOUS LUMBER

A. General: Provide lumber for support or attachment of other construction, including the following:

1. Blocking. 2. Nailers.

B. For items of dimension lumber size, provide Construction, Stud, or No. 2 grade lumber with 19 percent maximum moisture content and any of the following species:

1. Mixed southern pine; SPIB. 2. Hem-fir or Hem-fir (north); NLGA, WCLIB, or WWPA. 3. Spruce-pine-fir (south) or Spruce-pine-fir; NELMA, NLGA, WCLIB, or WWPA. 4. Western woods; WCLIB or WWPA.

2.4 FASTENERS

A. General: Provide fasteners of size and type that comply with requirements specified in this Article for material and manufacture.

1. Where rough carpentry is exposed to weather, or in ground contact, or is preservative-treated, or is in area of high relative humidity, provide fasteners with hot-dip zinc coating complying with ASTM A 153/A 153M.

B. Nails, Brads, and Staples: ASTM F 1667.

C. Power-Driven Fasteners: CABO NER-272.

D. Wood Screws: ASME B18.6.1.

E. Screws for Fastening to Cold-Formed Metal Framing: ASTM C 954, except with wafer heads and reamer wings, length as recommended by screw manufacturer for material being fastened.

F. Bolts: Steel bolts complying with ASTM A 307, Grade A; with ASTM A 563 hex nuts and, where indicated, flat washers.

G. Expansion Anchors: Anchor bolt and sleeve assembly of material indicated below with capability to sustain, without failure, a load equal to 6 times the load imposed when installed in unit masonry assemblies and equal to 4 times the load imposed when installed in concrete as determined by testing per ASTM E 488 conducted by a qualified independent testing and inspecting agency.

1. Material: Carbon-steel components, zinc plated to comply with ASTM B 633, Class Fe/Zn 5.


H. Bituminous Paint: Cold-applied asphalt-mastic paint complying with SSPC-Paint 12 requirements except containing no asbestos, formulated for 30-mil thickness per coat.

1. Apply to preservative treated wood where in contact with aluminum members faces.

PART 3 - EXECUTION

3.1 INSTALLATION, GENERAL

A. Set rough carpentry to required levels and lines, with members plumb, true to line, cut, and fitted. Fit rough carpentry to other construction; scribe and cope as needed for accurate fit. Locate furring, nailers, blocking, grounds, and similar supports to comply with requirements for attaching other construction.

B. Do not use materials with defects that impair quality of rough carpentry or pieces that are too small to use with minimum number of joints or optimum joint arrangement.

C. Securely attach rough carpentry work to substrate by anchoring and fastening as indicated, complying with the following:

1. NES NER-272 for power driven fasteners. 2. Table 2304.9.1, “Fastening Schedule,” in Ohio Building Code.

D. Use common wire nails, unless otherwise indicated. Select fasteners of size that will not fully penetrate members where opposite side will be exposed to view or will receive finish materials. Make tight connections between members. Install fasteners without splitting wood; predrill as required.

END OF SECTION

ROUGH CARPENTRY

SECTION 06 1000 -ROUGH CARPENTRY

PART 1 - GENERAL



1.2 SUMMARY

A. This section includes the following: 1. Wood blocking and nailers. 2. Plywood.

1.3 DEFINITIONS

A. Rough Carpentry: Carpentry work not specified in other Sections and not exposed, unless otherwise indicated.

B. Exposed Framing: Dimension lumber not concealed by other construction.

C. Dimension Lumber: Lumber of 2 inches nominal (38 mm actual) or greater but less than 5 inches nominal (114 mm actual) in least dimension.

D. Lumber grading agencies, and the abbreviations used to reference them, include the following:

1. NELMA - Northeastern Lumber Manufacturers Association. 2. NLGA - National Lumber Grades Authority. 3. RIS - Redwood Inspection Service. 4. SPIB - Southern Pine Inspection Bureau. 5. WCLIB - West Coast Lumber Inspection Bureau. 6. WWPA - Western Wood Products Association.

1.4 SUBMITTALS

A. Product Data: For each type of process and factory-fabricated product. Indicate component materials and dimensions and include construction and application details.

1. Include data for wood-preservative treatment from chemical treatment manufacturer and certification by treating plant that treated materials comply with requirements. Indicate type of preservative used, net amount of preservative retained, and chemical treatment manufacturer's written instructions for handling, storing, installing, and finishing treated material.

2. Include data for fire-retardant treatment from chemical treatment manufacturer and certification by treating plant that treated materials comply with requirements. Include physical properties of treated materials, both before and after exposure to elevated temperatures when tested according to ASTM D 5516 and ASTM D 5664.

ROUGH CARPENTRY

3. For products receiving a waterborne treatment, include statement that moisture content of treated materials was reduced to levels specified before shipment to Project site.

4. Include copies of warranties from chemical treatment manufacturers for each type of treatment.

B. Research/Evaluation Reports: For the following, showing compliance with building code in effect for Project:

1. Preservative-treated wood. 2. Fire-retardant-treated wood. 3. Power-driven fasteners. 4. Powder-actuated fasteners.


A. Stack lumber, plywood, and other panels; place spacers between each bundle to provide air circulation. Provide for air circulation around stacks and under coverings.

PART 2 - PRODUCTS

2.1 WOOD PRODUCTS, GENERAL

A. Lumber: DOC PS 20 and applicable rules of lumber grading agencies certified by the American Lumber Standards Committee Board of Review.

1. Factory mark each piece of lumber with grade stamp of grading agency. 2. Where nominal sizes are indicated, provide actual sizes required by DOC PS 20 for

moisture content specified. Where actual sizes are indicated, they are minimum dressed sizes for dry lumber.

3. Provide dressed lumber, S4S, unless otherwise indicated.

2.2 WOOD-PRESERVATIVE-TREATED MATERIALS

A. Preservative Treatment by Pressure Process: AWPA C2 (lumber) and AWPA C9 (plywood), except that lumber that is not in contact with the ground and is continuously protected from liquid water may be treated according to AWPA C31 with inorganic boron (SBX).

1. Preservative Chemicals: Acceptable to authorities having jurisdiction and the following:

a. Preservative chemicals containing no arsenic or chromium. b. Use treatment that does not promote corrosion of metal fasteners.

B. Kiln-dry material after treatment to a maximum moisture content of 19 percent for lumber and 15 percent for plywood. Do not use material that is warped or does not comply with requirements for untreated material.

C. Mark each treated item with the treatment quality mark of an inspection agency approved by the American Lumber Standards Committee Board of Review.

ROUGH CARPENTRY

D. Application: Treat items indicated on Drawings, and the following:

1. Exterior wood cants, nailers, curbs, equipment support bases, blocking, stripping, and similar members in connection with flashing, vapor barriers, and waterproofing.

2. Wood sills, sleepers, blocking, furring, stripping, and similar concealed members in contact with masonry or concrete.

3. Wood blocking, framing, sheathing and similar members in contact with curtain wall system.

4. Wood framing members less than 18 inches above grade. 5. Wood floor plates that are installed over concrete slabs directly in contact with earth.

2.3 FIRE-RETARDANT-TREATED MATERIALS

A. General: Where fire-retardant-treated materials are indicated, provide materials that comply with performance requirements in AWPA C20 (lumber) and AWPA C27 (plywood). Identify fire-retardant-treated wood with appropriate classification marking of UL, U.S. Testing, Timber Products Inspection, or another testing and inspecting agency acceptable to authorities having jurisdiction.

1. Use treatment for which chemical manufacturer publishes physical properties of treated wood after exposure to elevated temperatures, when tested by a qualified independent testing agency according to ASTM D 5664, for lumber and ASTM D 5516, for plywood.

2. Use treatment that does not promote corrosion of metal fasteners. 3. Use Exterior type for exterior locations. 4. Use Interior Type A High Temperature (HT), unless otherwise indicated.

B. Application: Treat items indicated on Drawings, and the following:

1. All concealed plywood and blocking, in interior construction. 2. Interior plywood backing panels.

2.4 MISCELLANEOUS LUMBER

A. General: Provide lumber for support or attachment of other construction, including the following:

1. Blocking. 2. Nailers.

B. For items of dimension lumber size, provide Construction, Stud, or No. 2 grade lumber with 19 percent maximum moisture content and any of the following species:

1. Mixed southern pine; SPIB. 2. Hem-fir or Hem-fir (north); NLGA, WCLIB, or WWPA. 3. Spruce-pine-fir (south) or Spruce-pine-fir; NELMA, NLGA, WCLIB, or WWPA. 4. Western woods; WCLIB or WWPA.

ROUGH CARPENTRY

2.5 FASTENERS

A. General: Provide fasteners of size and type that comply with requirements specified in this Article for material and manufacture.

1. Where rough carpentry is exposed to weather, or in ground contact, or is preservative-treated, or is in area of high relative humidity, provide fasteners with hot-dip zinc coating complying with ASTM A 153/A 153M.

B. Nails, Brads, and Staples: ASTM F 1667.

C. Power-Driven Fasteners: CABO NER-272.

D. Wood Screws: ASME B18.6.1.

E. Screws for Fastening to Cold-Formed Metal Framing: ASTM C 954, except with wafer heads and reamer wings, length as recommended by screw manufacturer for material being fastened.

F. Bolts: Steel bolts complying with ASTM A 307, Grade A; with ASTM A 563 hex nuts and, where indicated, flat washers.

G. Expansion Anchors: Anchor bolt and sleeve assembly of material indicated below with capability to sustain, without failure, a load equal to 6 times the load imposed when installed in unit masonry assemblies and equal to 4 times the load imposed when installed in concrete as determined by testing per ASTM E 488 conducted by a qualified independent testing and inspecting agency.

1. Material: Carbon-steel components, zinc plated to comply with ASTM B 633, Class Fe/Zn 5.

H. Bituminous Paint: Cold-applied asphalt-mastic paint complying with SSPC-Paint 12 requirements except containing no asbestos, formulated for 30-mil thickness per coat.

1. Apply to preservative treated wood where in contact with aluminum members faces.

PART 3 - EXECUTION


A. Set rough carpentry to required levels and lines, with members plumb, true to line, cut, and fitted. Fit rough carpentry to other construction; scribe and cope as needed for accurate fit. Locate furring, nailers, blocking, grounds, and similar supports to comply with requirements for attaching other construction.

B. Do not use materials with defects that impair quality of rough carpentry or pieces that are too small to use with minimum number of joints or optimum joint arrangement.

C. Securely attach rough carpentry work to substrate by anchoring and fastening as indicated, complying with the following:

1. NES NER-272 for power driven fasteners.

ROUGH CARPENTRY

2. Table 2304.9.1, “Fastening Schedule,” in Ohio Building Code.

D. Use common wire nails, unless otherwise indicated. Select fasteners of size that will not fully penetrate members where opposite side will be exposed to view or will receive finish materials. Make tight connections between members. Install fasteners without splitting wood; predrill as required.

3.2 WOOD BLOCKING AND NAILER INSTALLATION

A. Install where indicated and where required for screeding or attaching other work. Form to shapes indicated and cut as required for true line and level of attached work. Coordinate locations with other work involved.

B. Attach items to substrates to support applied loading. Recess bolts and nuts flush with surfaces, unless otherwise indicated. Build anchor bolts into masonry during installation of masonry work. Where possible, secure anchor bolts to formwork before concrete placement.

END OF SECTION

INTERIOR FINISH CARPENTRY 06 2023 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 06 2023 - INTERIOR FINISH CARPENTRY

PART 1 - GENERAL



1.2 SUMMARY

A. Section Includes:

1. Interior trim, including nonfire-rated interior door frames. 2. Interior stairs and railings.

B. Related Requirements:

1. Section 06 1000 "Rough Carpentry" for furring, blocking, and other carpentry work not exposed to view.

2. Section 09 9123 "Interior Painting" for priming and backpriming of interior finish carpentry.

1.3 DEFINITIONS

A. MDF: Medium-density fiberboard.

B. MDO: Plywood with a medium-density overlay on the face.

1.4 ACTION SUBMITTALS

A. Product Data: For each type of process and factory-fabricated product. Indicate component materials, dimensions, profiles, textures, and colors and include construction and application details.

1. Include data for wood-preservative treatment from chemical-treatment manufacturer and certification by treating plant that treated materials comply with requirements. Indicate type of preservative used and net amount of preservative retained. Include chemical-treatment manufacturer's written instructions for finishing treated material.

2. Include data for fire-retardant treatment from chemical-treatment manufacturer and certification by treating plant that treated materials comply with requirements.

3. For products receiving a waterborne treatment, include statement that moisture content of treated materials was reduced before shipment to Project site to levels specified.

B. Samples for Initial Selection: For each type of product involving selection of colors, profiles, or textures.


1.5 INFORMATIONAL SUBMITTALS

A. Evaluation Reports: For fire-retardant-treated wood, from ICC-ES.

B. Sample Warranty: For manufacturer's warranty.


A. Stack lumber, plywood, and other panels flat with spacers between each bundle to provide air circulation. Protect materials from weather by covering with waterproof sheeting, securely anchored. Provide for air circulation around stacks and under coverings.

B. Deliver interior finish carpentry materials only when environmental conditions comply with requirements specified for installation areas. If interior finish carpentry materials must be stored in other than installation areas, store only where environmental conditions comply with requirements specified for installation areas.

1.7 FIELD CONDITIONS

A. Environmental Limitations: Do not deliver or install interior finish carpentry materials until building is enclosed and weatherproof, wet work in space is completed and nominally dry, and HVAC system is operating and maintaining temperature and relative humidity at occupancy levels during the remainder of the construction period.

B. Do not install finish carpentry materials that are wet, moisture damaged, or mold damaged.

1. Indications that materials are wet or moisture damaged include, but are not limited to, discoloration, sagging, or irregular shape.

2. Indications that materials are mold damaged include, but are not limited to, fuzzy or splotchy surface contamination and discoloration.

1.8 WARRANTY

A. Manufacturer's Warranty for Columns: Manufacturer agrees to repair or replace columns that fail in materials or workmanship within specified warranty period.

1. Warranty Period for Columns: Five years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 MATERIALS, GENERAL

A. Lumber: DOC PS 20 and applicable rules of grading agencies indicated. If no grading agency is indicated, comply with the applicable rules of any rules-writing agency certified by the American Lumber Standard Committee's Board of Review. Grade lumber by an agency certified by the American Lumber Standard Committee's Board of Review to inspect and grade lumber under the rules indicated.


1. Factory mark each piece of lumber with grade stamp of grading agency. 2. For exposed lumber, mark grade stamp on end or back of each piece, or omit grade

stamp and provide certificates of grade compliance issued by grading agency.

B. Softwood Plywood: DOC PS 1.

C. Hardboard: ANSI A135.4.

D. MDF: ANSI A208.2, Grade 130.

E. Particleboard: ANSI A208.1, Grade M-2.

2.2 INTERIOR TRIM

A. Lumber Trim for Opaque Finish (Painted Finish): 1. Species and Grade: White woods, D Select. 2. Maximum Moisture Content: 19 with at least 85 percent of shipment at 12 percent or

less. 3. Maximum Moisture Content: 13 percent. 4. Finger Jointing: Match Existing. 5. Face Surface: Match existing. 6. Optional Material: Primed MDF of same actual dimensions as lumber indicated may be

used in lieu of lumber.

B. Moldings for Opaque Finish (Painted Finish): Made to patterns included in MMPA's "WM/Series Wood Moulding Patterns."

1. Softwood Moldings: MMPA WM 4, P grade.

a. Species: Eastern white, Idaho white, lodgepole, ponderosa, radiata, or sugar pine. b. Maximum Moisture Content: 15 percent with at least 85 percent of shipment at 12

percent or less.

2. Optional Material: Primed MDF. 3. Finger Jointing: Match Existing. 4. Base Pattern: Match existing base. 5. Shoe-Mold Pattern: Match existing shoe mold. 6. Casing Pattern: Match existing casing. 7. Mull-Casing Pattern: Match existing casing. 8. Stop Pattern: Match existing stop. 9. Chair-Rail Pattern: Match existing chair rail.

2.3 STAIRS AND RAILINGS

A. Treads: Depth to match existing, clear, kiln-dried, edge-glued, rift-sawn red oak, red oak, hard maple, or poplar stepping with half-round nosing.

B. Risers: Depth to match existing; clear, kiln-dried, edge-glued red oak, hard maple, or poplar stock.


C. Interior Railings: Clear, kiln-dried red oak, hard maple, or yellow poplar, either solid or laminated.

2.4 MISCELLANEOUS MATERIALS

A. Fasteners for Interior Finish Carpentry: Nails, screws, and other anchoring devices of type, size, material, and finish required for application indicated to provide secure attachment, concealed where possible.

B. Low-Emitting Materials: Adhesives shall comply with the testing and product requirements of the California Department of Public Health's "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers."

C. Glue: Aliphatic-resin, polyurethane, or resorcinol wood glue recommended by manufacturer for general carpentry use.

D. Installation Adhesive for Foam Plastic Moldings: Product recommended for indicated use by foam plastic molding manufacturer.

E. Paneling Adhesive: Comply with paneling manufacturer's written recommendations for adhesives.

F. Multipurpose Construction Adhesive: Formulation complying with ASTM D 3498 that is recommended for indicated use by adhesive manufacturer.

2.5 FABRICATION

A. Back out or kerf backs of the following members, except those with ends exposed in finished work:

1. Interior standing and running trim, except shoe and crown molds. 2. Wood-board paneling.

B. Ease edges of lumber less than 1 inch (25 mm) in nominal thickness to 1/16-inch (1.5-mm) radius and edges of lumber 1 inch (25 mm) or more in nominal thickness to 1/8-inch (3-mm) radius.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.

B. Examine finish carpentry materials before installation. Reject materials that are wet, moisture damaged, and mold damaged.

C. Proceed with installation only after unsatisfactory conditions have been corrected.


3.2 PREPARATION

A. Clean substrates of projections and substances detrimental to application.

B. Before installing interior finish carpentry, condition materials to average prevailing humidity in installation areas for a minimum of 24 hours unless longer conditioning is recommended by manufacturer.


A. Do not use materials that are unsound; warped; improperly treated or finished; inadequately seasoned; too small to fabricate with proper jointing arrangements; or with defective surfaces, sizes, or patterns.

B. Install interior finish carpentry level, plumb, true, and aligned with adjacent materials. Use concealed shims where necessary for alignment.

1. Scribe and cut interior finish carpentry to fit adjoining work. Refinish and seal cuts as recommended by manufacturer.

2. Where face fastening is unavoidable, countersink fasteners, fill surface flush, and sand unless otherwise indicated.

3. Install to tolerance of 1/8 inch in 96 inches (3 mm in 2438 mm) for level and plumb. Install adjoining interior finish carpentry with 1/32-inch (0.8-mm) maximum offset for flush installation and 1/16-inch (1.5-mm) maximum offset for reveal installation.

4. Install stairs with no more than 3/16-inch (4.7-mm) variation between adjacent treads and risers and with no more than 3/8-inch (9.5-mm) variation between largest and smallest treads and risers within each flight.

5. Coordinate interior finish carpentry with materials and systems in or adjacent to it. Provide cutouts for mechanical and electrical items that penetrate interior finish carpentry.

3.4 STANDING AND RUNNING TRIM INSTALLATION

A. Install with minimum number of joints practical, using full-length pieces from maximum lengths of lumber available. Do not use pieces less than 24 inches (610 mm) long, except where necessary. Stagger joints in adjacent and related standing and running trim. Cope or Miter at returns to match existing construction, miter at outside corners, and cope at inside corners to produce tight-fitting joints with full-surface contact throughout length of joint. Use scarf joints for end-to-end joints. Plane backs of casings to provide uniform thickness across joints where necessary for alignment.

1. Match color and grain pattern of trim for transparent finish (stain or clear finish) across joints.

2. Install trim after gypsum-board joint finishing operations are completed. 3. Install without splitting; drill pilot holes before fastening where necessary to prevent

splitting. Fasten to prevent movement or warping. Countersink fastener heads on exposed carpentry work and fill holes.


3.5 STAIR AND RAILING INSTALLATION

A. Treads and Risers at Interior Stairs: Secure treads and risers by gluing and nailing to rough carriages.

B. Railings: Secure wall rails with metal brackets. Fasten freestanding railings to newel posts and to trim at walls with countersunk-head wood screws (or rail bolts) and glue. Assemble railings at goosenecks, easements, and splices with rail bolts and glue.

3.6 ADJUSTING

A. Replace interior finish carpentry that is damaged or does not comply with requirements. Interior finish carpentry may be repaired or refinished if work complies with requirements and shows no evidence of repair or refinishing. Adjust joinery for uniform appearance.

3.7 CLEANING

A. Clean interior finish carpentry on exposed and semiexposed surfaces. Restore damaged or soiled areas and touch up factory-applied finishes if any.

3.8 PROTECTION

A. Protect installed products from damage from weather and other causes during construction.

B. Remove and replace finish carpentry materials that are wet, moisture damaged, and mold damaged.

1. Indications that materials are wet or moisture damaged include, but are not limited to, discoloration, sagging, or irregular shape.

2. Indications that materials are mold damaged include, but are not limited to, fuzzy or splotchy surface contamination and discoloration.

END OF SECTION 06 2023

ASPHALT SHINGLES 07 3113 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 07 3113 - ASPHALT SHINGLES

PART 1 - GENERAL



1.2 SUMMARY


1. Asphalt shingles. 2. Underlayment. 3. Ridge vents. 4. Metal flashing and trim.

1.3 DEFINITION

A. Roofing Terminology: See ASTM D 1079 and glossary of NRCA's "The NRCA Roofing and Waterproofing Manual" for definitions of terms related to roofing work in this Section.

1.4 PREINSTALLATION MEETINGS

A. Preinstallation Conference: Conduct conference at Project site.


A. Product Data: For each type of product.

B. Samples: For each exposed product and for each color and texture specified.

1. Asphalt Shingles: Full size. 2. Ridge and Hip Cap Shingles: Full size. 3. Ridge Vent: 12-inch- (300-mm-) long Sample. 4. Exposed Valley Lining: 12 inches (300 mm) square.

C. Samples for Initial Selection: For each type of asphalt shingle indicated.

1. Include similar Samples of accessories involving color selection.

D. Samples for Verification: For the following products, of sizes indicated:

1. Asphalt Shingles: Full size.


2. Ridge and Hip Cap Shingles: Full size. 3. Ridge Vent: 12-inch- (300-mm-) long Sample. 4. Exposed Valley Lining: 12 inches (300 mm) square.


A. Qualification Data: For Installer.

B. Product Test Reports: For each type of asphalt shingle and underlayment product indicated, for tests performed by manufacturer and witnessed by a qualified testing agency.

C. Sample Warranty: For manufacturer's warranty.

1.7 CLOSEOUT SUBMITTALS

A. Maintenance Data: For asphalt shingles to include in maintenance manuals.

1.8 MAINTENANCE MATERIAL SUBMITTALS

A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.

1. Asphalt Shingles: 100 sq. ft. (9.3 sq. m) of each type, in unbroken bundles.

1.9 QUALITY ASSURANCE

A. Installer Qualifications: An authorized representative who is trained and approved by manufacturer.


A. Store roofing materials in a dry, well-ventilated location protected from weather, sunlight, and moisture according to manufacturer's written instructions.

B. Store underlayment rolls on end on pallets or other raised surfaces. Do not double stack rolls.

C. Protect unused roofing materials from weather, sunlight, and moisture when left overnight or when roofing work is not in progress.

D. Handle, store, and place roofing materials in a manner to prevent damage to roof deck or structural supporting members.

1.11 FIELD CONDITIONS

A. Environmental Limitations: Install self-adhering sheet underlayment within the range of ambient and substrate temperatures recommended in writing by manufacturer.


1.12 WARRANTY

A. Manufacturer's Warranty: Manufacturer agrees to repair or replace asphalt shingles that fail within specified warranty period.

1. Failures include, but are not limited to, the following:

a. Manufacturing defects.

2. Material Warranty Period: 40 years from date of Substantial Completion, prorated, with first five years nonprorated.

3. Wind-Speed Warranty Period: Asphalt shingles will resist blow-off or damage caused by wind speeds of up to 80 mph (36 m/s) for five years from date of Substantial Completion.

4. Algae-Resistance Warranty Period: Asphalt shingles will not discolor for five years from date of Substantial Completion.

B. Roofing Installer's Warranty: On warranty form at end of this Section, signed by Installer, in which Installer agrees to repair or replace components of asphalt-shingle roofing that fail in materials or workmanship within specified warranty period.

1. Warranty Period: Two years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 GLASS-FIBER-REINFORCED ASPHALT SHINGLES

A. Laminated-Strip Asphalt Shingles: ASTM D 3462/D 3462M, laminated, multi-ply overlay construction, glass-fiber reinforced, mineral-granule surfaced, and self-sealing.

1. Manufacturers: a. Owens Corning, Oakridge Pro 40 Shadow. b. GAF/ELK, Timberline Prestique. c. Certainteed, Landmark 40.

2. Butt Edge: Straight cut. 3. Strip Size: Manufacturer's standard. 4. Algae Resistance: Granules resist algae discoloration. 5. Color and Blends: As selected by Architect from manufacturer's full range.

2.2 UNDERLAYMENT MATERIALS

A. Felt: ASTM D 226/D 226M, asphalt-saturated organic felts, nonperforated.

1. Type: Type I.

B. Self-Adhering Sheet Underlayment, Granular Surfaced: ASTM D 1970/D 1970M, minimum of 55-mil- (1.4-mm-) thick sheet; glass-fiber-mat-reinforced, SBS-modified asphalt; mineral-granule


surfaced; with release backing; cold applied. Provide primer for adjoining concrete or masonry surfaces to receive underlayment.

1. Manufacturers: a. Atlas Roofing Corporation b. Carlisle c. CertainTeed Corporation d. Owens Corning

2.3 VENTS

A. Rigid Ridge Vent: Manufacturer's standard, rigid section high-density polypropylene or other UV-stabilized plastic ridge vent for use under ridge shingles.

1. Manufacturers: a. CertainTeed b. GAF c. Owens Corning d. Cor-A-Vent e. Air Vent Inc.

2. Minimum Net Free Area: 18 sq. in. per lineal foot. 3. Width: 8”.

2.4 ACCESSORIES

A. Asphalt Roofing Cement: ASTM D 4586, Type II, asbestos free.

B. Roofing Nails: ASTM F 1667; aluminum, stainless-steel, copper, or hot-dip galvanized-steel wire shingle nails, minimum 0.120-inch- (3-mm-) diameter, sharp-pointed, with a minimum 3/8-inch- (9.5-mm-) diameter flat head and of sufficient length to penetrate 3/4 inch (19 mm) into solid wood decking or extend at least 1/8 inch (3 mm) through OSB or plywood sheathing.

1. Shank: Barbed. 2. Where nails are in contact with metal flashing, use nails made from same metal as

flashing.

C. Felt-Underlayment Nails: Aluminum, stainless-steel, or hot-dip galvanized-steel wire with low-profile capped heads or disc caps, 1-inch (25-mm) minimum diameter.

2.5 METAL FLASHING AND TRIM

A. General: Comply with requirements in Section 07 62 00 "Sheet Metal Flashing and Trim."

1. Sheet Metal: Coil-coated aluminum.

B. Fabricate sheet metal flashing and trim to comply with recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of the item.

http://www.specagent.com/LookUp/?ulid=4749&mf=04&src=wd


1. Apron Flashings: Fabricate with lower flange a minimum of 5 inches (125 mm) over and 4 inches (100 mm) beyond each side of downslope asphalt shingles and 6 inches (150 mm) up the vertical surface.

2. Step Flashings: Fabricate with a headlap of 2 inches (50 mm) and a minimum extension of 5 inches (125 mm) over the underlying asphalt shingle and up the vertical surface.

3. Cricket or Backer Flashings: Fabricate with concealed flange extending a minimum of 24 inches (600 mm) beneath upslope asphalt shingles and 6 inches (150 mm) above the roof plane.

4. Open Valley Flashings: Fabricate in lengths not exceeding 10 feet with 1-inch- high inverted-V profile at center of valley and equal flange widths of 10 inches

5. Drip Edges: Fabricate in lengths not exceeding 10 feet (3 m) with 2-inch (50-mm) roof-deck flange and 1-1/2-inch (38-mm) fascia flange with 3/8-inch (9.5-mm) drip at lower edge.

C. Vent Pipe Flashings: ASTM B 749, Type L51121, at least 1/16 inch (1.6 mm) thick. Provide lead sleeve sized to slip over and turn down into pipe, soldered to skirt at slope of roof, and extending at least 4 inches (100 mm) from pipe onto roof.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.

1. Examine roof sheathing to verify that sheathing joints are supported by framing and blocking or metal clips and that installation is within flatness tolerances.

2. Verify that substrate is sound, dry, smooth, clean, sloped for drainage, and completely anchored; and that provisions have been made for flashings and penetrations through asphalt shingles.

B. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work.


3.2 UNDERLAYMENT INSTALLATION

A. General: Comply with underlayment manufacturer's written installation instructions applicable to products and applications indicated unless more stringent requirements apply.

B. Single-Layer Felt Underlayment: Install on roof deck parallel with and starting at the eaves. Lap sides a minimum of 2 inches (50 mm) over underlying course. Lap ends a minimum of 4 inches (100 mm). Stagger end laps between succeeding courses at least 72 inches (1830 mm). Fasten with felt-underlayment nails.

1. Install felt underlayment on roof deck not covered by self-adhering sheet underlayment. Lap sides of felt over self-adhering sheet underlayment not less than 3 inches (75 mm) in


direction that sheds water. Lap ends of felt not less than 6 inches (150 mm) over self-adhering sheet underlayment.

2. Install fasteners at no more than 36 inches (914 mm) o.c.

C. Self-Adhering Sheet Underlayment: Install, wrinkle free, on roof deck. Comply with low-temperature installation restrictions of underlayment manufacturer if applicable. Install lapped in direction that sheds water. Lap sides not less than 3-1/2 inches (89 mm). Lap ends not less than 6 inches (150 mm) staggered 24 inches (600 mm) between courses. Roll laps with roller. Cover underlayment within seven days. 1. Eaves: Extend from edges of eaves 36 inches (914 mm) beyond interior face of exterior

wall. 2. Rakes: Extend from edges of rake 24 inches (600 mm) beyond interior face of exterior

wall. 3. Valleys: Extend from lowest to highest point 18 inches (450 mm) on each side. 4. Hips: Extend 18 inches (450 mm) on each side. 5. Ridges: Extend 36 inches (914 mm) on each side without obstructing continuous ridge

vent slot. 6. Dormers, Chimneys, Skylights, and Other Roof-Penetrating Elements: Extend beyond

penetrating element 18 inches (450 mm), and return vertically against penetrating element not less than 4 inches (100 mm).

7. Roof Slope Transitions: Extend 18 inches (450 mm) on each roof slope.

D. Metal-Flashed, Open-Valley Underlayment: Install two layers of minimum 36-inch- (914-mm-) wide underlayment centered in valley. Stagger end laps between layers at least 72 inches (1830 mm). Lap ends of each layer at least 12 inches (300 mm) in direction to shed water, and seal with asphalt roofing cement. Fasten each layer to roof deck.

1. Lap roof-deck underlayment over first layer of valley underlayment at least 6 inches (150 mm).

2. Lap roof-deck felt underlayment over valley felt underlayment at least 6 inches (150 mm).

3. Install an 18-inch- (450-mm-) wide strip of valley lining centered in valley, with granular-surface face down. Install a second 36-inch- (914-mm-) wide strip of valley lining centered in valley, with granular-surface face up. Lap ends of each strip at least 12 inches (300 mm) in direction to shed water, and seal with asphalt roofing cement. Stagger end laps between succeeding strips at least 72 inches (1830 mm). Fasten each strip to roof deck with roofing nails.

3.3 METAL FLASHING INSTALLATION

A. General: Install metal flashings and other sheet metal to comply with requirements in Section 07 62 00 "Sheet Metal Flashing and Trim."

1. Install metal flashings according to recommendations in ARMA's "Residential Asphalt Roofing Manual" and NRCA's "NRCA Guidelines for Asphalt Shingle Roof Systems."

B. Apron Flashings: Extend lower flange over and beyond each side of downslope asphalt shingles and up the vertical surface.


C. Step Flashings: Install with a headlap of 2 inches (50 mm) and extend over the underlying asphalt shingle and up the vertical surface. Fasten to roof deck only.

D. Cricket or Backer Flashings: Install against the roof-penetrating element extending concealed flange beneath upslope asphalt shingles and beyond each side.

E. Open-Valley Flashings: Install centered in valleys, lapping ends at least 8 inches (200 mm) in direction to shed water. Fasten upper end of each length to roof deck beneath overlap.

1. Secure hemmed flange edges into metal cleats spaced 12 inches (300 mm) apart and fastened to roof deck.

2. Adhere 9-inch- (225-mm-) wide strip of self-adhering sheet to metal flanges and to self-adhering sheet underlayment.

F. Rake Drip Edges: Install rake drip-edge flashings over underlayment and fasten to roof deck.

G. Eave Drip Edges: Install eave drip-edge flashings below underlayment and fasten to roof sheathing.

H. Pipe Flashings: Form flashing around pipe penetrations and asphalt shingles. Fasten and seal to asphalt shingles as recommended by manufacturer.

3.4 ASPHALT-SHINGLE INSTALLATION

A. General: Install asphalt shingles according to manufacturer's written instructions, recommendations in ARMA's "Residential Asphalt Roofing Manual," and recommendations in NRCA's "NRCA Guidelines for Asphalt Shingle Roof Systems."

B. Install starter strip along lowest roof edge, consisting of an asphalt-shingle strip with tabs removed at least 7 inches (175 mm) wide with self-sealing strip face up at roof edge.

1. Extend asphalt shingles 1/2 inch (13 mm) over fasciae at eaves and rakes. 2. Install starter strip along rake edge.

C. Install first and remaining courses of asphalt shingles stair-stepping diagonally across roof deck with manufacturer's recommended offset pattern at succeeding courses, maintaining uniform exposure.

D. Install first and remaining courses of asphalt shingles stair-stepping diagonally across roof deck with manufacturer's recommended offset pattern at succeeding courses, maintaining uniform exposure.

E. Install asphalt shingles by single-strip column or racking method, maintaining uniform exposure. Install full-length first course followed by cut second course, repeating alternating pattern in succeeding courses.

F. Fasten asphalt-shingle strips with a minimum of [four] [five] [six] <Insert number> roofing nails located according to manufacturer's written instructions. 1. When ambient temperature during installation is below 50 deg F (10 deg C), seal asphalt

shingles with asphalt roofing cement spots.


G. Open Valleys: Cut and fit asphalt shingles at open valleys, trimming upper concealed corners of shingle strips. [Maintain uniform width of exposed open valley] [Widen exposed portion of open valley 1/8 inch in 12 inches (1:96)] from highest to lowest point.

1. Set valley edge of asphalt shingles in a 3-inch- (75-mm-) wide bed of asphalt roofing cement.

2. Do not nail asphalt shingles to metal open-valley flashings.

H. Ridge Vents: Install continuous ridge vents over asphalt shingles according to manufacturer's written instructions. Fasten with roofing nails of sufficient length to penetrate sheathing.

I. Hip and Ridge Shingles: Maintain same exposure of cap shingles as roofing shingle exposure. Lap cap shingles at ridges to shed water away from direction of prevailing winds. Fasten with roofing nails of sufficient length to penetrate sheathing.

1. Fasten ridge cap asphalt shingles to cover ridge vent without obstructing airflow.


SIDING 07 4600 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 07 4600 – SIDING

PART 1 - GENERAL



1.2 SUMMARY


1. Vinyl siding. 2. Building wrap.

1.3 REFERENCES

A. ASTM D 3679 - Specification for Rigid Poly Vinyl Chloride (PVC) Siding.

B. ASTM D 4226 - Test Methods for Impact Resistance of Rigid Poly Vinyl Chloride (PVC)

Building Products.

C. ASTM E 84 - Test Method for Surface Burning Characteristics of Building Materials.

D. ASTM C 920; Standard Specification for Elastomeric Joint Sealants

E. ASTM C 1193; Standard Guide for Use of Joint Sealants

F. ASTM D 882; Test Method for Tensile Properties of Thin Plastic Sheeting

G. ASTM D 1117; Standard Guide for Evaluating Non-woven Fabrics

H. ASTM E 96; Test Method for Water Vapor Transmission of Materials

I. ASTM E 1677; Specification for Air Retarder Material or System for Framed Building Walls

J. ASTM E 2178; Test Method for Air Permeance of Building Materials

K. AATCC – American Association of Textile Chemists & Colorists 1. Test Method 127 Water Resistance: Hydrostatic Pressure Test

L. TAPPI

1. Test Method T-410; Grams of Paper and Paperboard (Weight per Unit Area) 2. Test Method T-460; Air Resistance of Paper (Gurley Hill Method)

1.4 SUBMITTALS

A. Product Data: For each type of product indicated. Include construction details, materi-

al descriptions, dimensions of individual components and profiles, and finishes.


B. Product Data: For building wrap, include data on air and water-vapor permeance based on testing according to referenced standards.

C. Qualification Data: For qualified vinyl siding Installer.

D. Product Certificates: For each type of siding, from manufacturer.

E. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified

testing agency, for vinyl siding.

F. Research/Evaluation Reports: For each type of siding required.

G. Maintenance Data: For each type of siding and related accessories to include in mainte-nance manuals.

H. Warranty: Sample of special warranty.


A. Vinyl Siding Installer Qualifications: A qualified installer who employs a VSI-Certified

Installer on Project.

B. Vinyl Siding Certification Program: Provide vinyl siding products that are listed in VSI's list of certified products.

C. Source Limitations: Obtain each type, color, texture, and pattern of siding including related

accessories, from single source from single manufacturer. 1.6 DELIVERY, STORAGE, AND HANDLING

A. Store materials in a dry, well-ventilated, weathertight place.

1.7 COORDINATION

A. Coordinate installation with flashings and other adjoining construction to ensure prop-

er sequencing. 1.8 SIDING WARRANTY

A. Special Warranty: Standard form in which manufacturer agrees to repair or replace siding that

fail(s) in materials or workmanship within specified warranty period.


a. Structural failures including cracking, deforming and fading.

2. Fading is defined as loss of color, after cleaning with product recommended by manu-facturer, of more than 4 Hunter color-difference units as measured according to ASTM D 2244.


1.9 Warranty Period: 10 years from date of Substantial Completion. WEATHER-RESISTIVE BARRIER WARRANTY

A. Provide manufacturer’s standard 10 year water-tightness warranty covering material

and installation 1.10 EXTRA MATERIALS

A. Furnish extra siding materials that match products installed and that are packaged

with protective covering for storage and identified with labels describing contents.

1. Furnish full lengths of siding including related accessories, in a quantity equal to 2 percent of amount installed.

PART 2 - PRODUCTS

2.1 MANUFACTURER

A. Basis-of-Design Product: Subject to compliance with requirements, provide Alside; Coventry or comparable product by one of the following:

1. CertainTeed Corp. 2. Owens Corning.

2.2 MATERIALS

A. General: Vinyl Siding: Produced from polyvinyl chloride (PVC) compounds meeting ASTM D 3679 requirements for compound class number 2.

1. Flame Spread Index: 20 (Class A), when tested in accordance with ASTM E 84. 2. Smoke Developed Index: Less than 450, when tested in accordance with ASTM E 84. 3. Ignition Temperature: When tested in accordance with ASTM D 1929, no self ignition

and no flaming; no smoldering at less than 680 degrees F (360 degrees C). 4. Impact Resistance: 60 in-lbf, per ASTM D 4226, Procedure A, H.25. 5. Weatherability: No surface or structural defects such as peeling, cracking, or chipping

when tested per ASTM D 3679. 6. Coefficient of Linear Expansion: 3.05 by 10-5 in/in F, per ASTM D 696. 7. Surface Distortion: No distortion at 120 degrees F (40.5 degrees C), per ASTM D 3679. 8. Interlock: Post-form style lock with positive interlock; both ends of panels factory cut

and notched for overlap. 9. Nail Slots: Elongated 1-inch (25 mm) slots spaced approximately 1/4 inch (6 mm) apart

in nailing hem to allow for expansion and contraction. 10. Weep Holes: Small holes under the bottom butt of siding panels to prevent vapor build-

up and allow accumulated moisture to escape

B. Horizontal Pattern: Match existing.


C. Texture: Match existing.

D. Nominal Thickness: Minimum 0.040 inch.

E. Minimum Profile Depth (Butt Thickness): Match existing.

F. Nailing Hem: Double thickness.

G. Finish: Match existing.

H. Colors: As selected by Architect from manufacturer's full range of industry colors.

2.3 ACCESSORIES

A. Siding Accessories, General: Provide starter strips, edge trim, outside and inside corner caps, and other items as recommended by siding manufacturer for building configuration.

1. Provide accessories matching color and texture of adjacent siding unless otherwise

indicated.

B. Vinyl Accessories: Integrally colored vinyl accessories complying with ASTM D 3679 except for wind-load resistance.

1. Texture: Match existing.

C. Decorative Accessories: Provide the following vinyl decorative accessories as indicated:

1. Louvers where required. 2. Moldings and trim.

D. Colors for Decorative Accessories: As selected by Architect from manufacturer's full range of

industry colors

E. Fasteners:

1. For fastening to wood, use siding nails of sufficient length to penetrate a minimum of 1 inch into substrate.

2. For fastening vinyl, use hot-dip galvanized fasteners 1/8 inch in diameter and nail head of 3/8 inch or larger.

2.4 WEATHER-RESISTIVE BARRIER

A. Manufacturer:

1. Basis-of-Design Product: Subject to compliance with requirements, provide DuPont Building Innovations: E. I. du Pont de Nemours and Company; Tyvek CommercialWrap or comparable product by one of the following:

a. Dow Chemical Company (The). b. Pactiv Corporation.

B. Materials:


1. High-performance, flash spun-bonded olefin, non-woven, non-perforated, sec-ondary weather barrier and related assembly components.

C. Performance Characteristics:

1. Air Penetration: 0.001 cfm/ft2 at 75 Pa, when tested in accordance with ASTM E

2178. Type I per ASTM E 1677.

2. Water Vapor Transmission: 28 perms, when tested in accordance with ASTM E 96, Method B.

3. Water Penetration Resistance: Minimum 280 cm when tested in accordance with AATCC Test Method 127.

4. Basis Weight: Minimum 2.7 oz/yd2, when tested in accordance with TAPPI Test Method T-410.

5. Air Resistance of Paper: Air infiltration at >1500 seconds, when tested in accord-ance with TAPPI Test Method T-460.

6. Tensile Strength: Minimum 38/35 lbs/in., when tested in accordance with ASTM D 882, Method A.

7. Tear Resistance: 12/10 lbs., when tested in accordance with ASTM D 1117. 8. Surface Burning Characteristics: Class A, when tested in accordance with ASTM E 84.

Flame Spread: 10, Smoke Developed: 10.

D. Building-Wrap Tape: Pressure-sensitive plastic tape recommended by building-wrap manufacturer for sealing joints and penetrations in building wrap.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates for compliance with requirements for installation tolerances and

other conditions affecting performance of siding and related accessories.

B. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 PREPARATION

A. Clean substrates of projections and substances detrimental to application.

3.3 INSTALLATION

A. General: Comply with siding manufacturer's written installation instructions applicable

to products and applications indicated unless more stringent requirements apply.


1. Do not install damaged components. 2. Center nails in elongated nailing slots without binding siding to allow for

thermal movement.

B. Install vinyl siding and related accessories according to ASTM D 4756. 3.4 Install fasteners for vinyl siding no more than 16 inches on center. WATER-RESISTIVE

BARRIER INSTALLATION

A. Building Wrap: Comply with manufacturer's written instructions.

1. Seal seams, edges, fasteners, and penetrations with tape. 2. Extend into jambs of openings where occur and seal corners with tape.

3.5 PROTECTION

A. Protect installed weather barrier from damage.

3.6 ADJUSTING AND CLEANING

A. Remove damaged, improperly installed, or otherwise defective materials and replace with

new materials complying with specified requirements.

B. Clean finished surfaces according to manufacturer's written instructions and maintain in a clean condition during construction.


SHEET METAL FLASHING AND TRIM 07 6200 - 1 SMHA Scattered Site Renovation 2017349.01

March 01, 2017

SECTION 07 6200 – SHEET METAL FLASHING AND TRIM

PART 1 - GENERAL



1.2 SUMMARY


1. Metal flashings and trim.

1.3 RELATED SECTIONS:

A. Division 06 Section "Miscellaneous Rough Carpentry" for wood nailers, curbs, and blocking.

B. Division 07 Section "Siding" for vinyl siding.

C. Division 07 Section "Joint Sealants" for sheet metal flashing and trim.

1.4 COORDINATION

A. Coordinate sheet metal flashing and trim layout and seams with sizes and locations of penetrations to be flashed, and joints and seams in adjacent materials.

B. Coordinate sheet metal flashing and trim installation with adjoining roofing and wall materials, joints, and seams to provide leak proof, secure, and noncorrosive installation.



1. Include construction details, material descriptions, dimensions of individual components and pro-files, and finishes for each manufactured product and accessory.

B. Shop Drawings: For sheet metal flashing and trim.

1.6 Shop Drawings of each item specified showing layout, profiles, methods of joining, and anchorage details.


A. Sheet Metal Standard for Flashing and Trim: Comply with SMACNA's "Architectural Sheet Metal Manual" requirements for dimensions and profiles shown unless more stringent require-ments are indicated.

B. Fabricator Qualifications: Employs skilled workers who custom fabricate sheet metal flashing and trim similar to that required for this Project and whose products have a record of success-ful in-service performance.

C. Preinstallation Conference: Conduct conference at Project site.


March 01, 2017


A. Do not store sheet metal flashing and trim materials in contact with other materials that might

cause staining, denting, or other surface damage. Store sheet metal flashing and trim materi-als away from uncured concrete and masonry.

B. Protect strippable protective covering on sheet metal flashing and trim from exposure to sun-light and high humidity, except to extent necessary for period of sheet metal flashing and trim installation.

PART 2 - PRODUCTS

2.1 PERFORMANCE REQUIREMENTS

A. General: Sheet metal flashing and trim assemblies shall withstand wind loads, structural move-ment, thermally induced movement, and exposure to weather without failure due to defective manufacture, fabrication, installation, or other defects in construction. Completed sheet met-al flashing and trim shall not rattle, leak, or loosen, and shall remain watertight.

B. Thermal Movements: Allow for thermal movements from ambient and surface temperature changes.

2.2 SHEET METALS

A. General: Protect mechanical and other finishes on exposed surfaces from damage by applying strippable, temporary protective film before shipping.

B. Aluminum Sheet: ASTM B 209 (ASTM B 209M), alloy as standard with manufacturer for finish required, with temper as required to suit forming operations and performance required; with smooth, flat surface.

1. Exposed Coil-Coated Finish:

Fluoropolymer 2-Coat System: Manufacturer's standard 2-coat, thermocured system consisting of specially formulated inhibitive primer and fluoropolymer color topcoat containing not less than 70 percent polyvinylidene fluoride resin by weight; complying with AAMA 2605.

a. Colors: To be selected by Architect from manufacturer’s full range of colors.


A. Felt: ASTM D226/D226M, Type II (No.30), asphalt-saturated organic felt; nonperforated.


A. General: Provide materials and types of fasteners, solder, protective coatings, sealants, and other miscellaneous items as required for complete sheet metal flashing and trim installation and as recommended by manufacturer of primary sheet metal or manufactured item un-less otherwise indicated.

B. Fasteners: Self-tapping screws, self-locking rivets and bolts, and other suitable fasteners de-signed to withstand design loads and recommended by manufacturer of primary sheet met-al or manufactured item.

C. Elastomeric Sealant: ASTM C 920, elastomeric silicone polymer sealant; of type, grade, class,


March 01, 2017

and use classifications required to seal joints in sheet metal flashing and trim and re-main watertight.

D. Butyl Sealant: ASTM C 1311, single-component, solvent-release butyl rubber sealant; polyiso-butylene plasticized; heavy bodied for hooked-type expansion joints with limited movement.

2.5 Epoxy Seam Sealer: Two-part, noncorrosive, aluminum seam-cementing compound, recom-mended by aluminum manufacturer for exterior nonmoving joints, including riveted joints. FABRICATION, GENERAL

A. General: Custom fabricate sheet metal flashing and trim to comply with details shown and recommendations in cited sheet metal standard that apply to design, dimensions, geome-try, metal thickness, and other characteristics of item required. Fabricate sheet metal flashing and trim in shop to greatest extent possible. Fabricate units with adequate provisions for support and anchorage, of the types needed for the indicated method of installation.

1. Thickness: As indicted or as recommended by SMACNA's "Architectural Sheet Metal Manual". 2. Seams for Aluminum: Fabricate nonmoving seams with flat-lock seams. Form seams and seal with epoxy seam sealer.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with re-quirements for installation tolerances, substrate, and other conditions affecting performance of the Work.

1. Verify compliance with requirements for installation tolerances of substrates. 2. Verify that substrate is sound, dry, smooth, clean, sloped for drainage, and securely an-

chored.

B. Proceed with installation only after unsatisfactory conditions have been corrected.


A. General: Anchor sheet metal flashing and trim and other components of the Work securely in place, with provisions for thermal and structural movement. Use fasteners, solder, protective coatings, separators, sealants, and other miscellaneous items as required to complete sheet metal flashing and trim system.

B. Metal Protection: Where dissimilar metals contact each other, or where metal contacts pres-sure-treated wood or other corrosive substrates, protect against galvanic action or corrosion by painting contact surfaces with bituminous coating or by other permanent separation as recommended by sheet metal manufacturer or cited sheet metal standard.

C. Fasteners: Use fastener sizes that penetrate wood blocking or sheathing not less than 1-1/4 inches (32 mm) for nails and not less than 3/4 inch (19 mm) for wood screws or substrate not less than recommended by fastener manufacturer to achieve maximum pull-out resistance.

D. Conceal fasteners and expansion provisions where possible in exposed work and locate to minimize possibility of leakage. Cover and seal fasteners and anchors as required for a tight installation. Seal joints as required for watertight construction.

3.3 CLEANING AND PROTECTION

A. Clean off excess sealants.

B. Remove temporary protective coverings and strippable films as sheet metal flashing and trim


March 01, 2017

are installed unless otherwise indicated in manufacturers written installation instructions. On completion of sheet metal flashing and trim installation, remove unused materials and clean finished surfaces as recommended by sheet metal flashing and trim manufacturer. Maintain sheet metal flashing and trim in clean condition during construction.

C. Replace sheet metal flashing and trim that have been damaged or that have deteriorated beyond successful repair by finish touchup or similar minor repair procedures.


ROOF SPECIALTIES

SECTION 07 7100 - ROOF SPECIALTIES

PART 1 - GENERAL



1.2 SUMMARY


1. Roof-edge flashings. 2. Roof-edge drainage systems. 3. Vinyl soffit panels.

B. Related Sections:

1. Division 06 Section "Miscellaneous Rough Carpentry" for wood nailers, curbs, and blocking.

2. Division 07 Section "Joint Sealants" for field-applied sealants between roof specialties and adjacent materials.


A. General Performance: Roof specialties shall withstand exposure to weather and resist thermally induced movement without failure, rattling, leaking, or fastener disengagement due to defective manufacture, fabrication, installation, or other defects in construction.

B. FM Approvals' Listing: Manufacture and install copings and roof-edge flashings that are listed in FM Approvals' "RoofNav" and approved for windstorm classification, Class 1-90. Identify materials with FM Approvals' markings.

C. SPRI Wind Design Standard: Manufacture and install copings and roof-edge flashings tested according to SPRI ES-1 and capable of resisting the following design pressures:

1. Design Pressure: As indicated on Drawings.

D. Thermal Movements: Allow for thermal movements from ambient and surface temperature changes to prevent buckling, opening of joints, hole elongation, overstressing of components, failure of joint sealants, failure of connections, and other detrimental effects. Provide clips that resist rotation and avoid shear stress as a result of thermal movements. Base calculations on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss.

1. Temperature Change (Range): 120 deg F, ambient, material surfaces.

ROOF SPECIALTIES

1.4 SUBMITTALS

A. Product Data: For each type of product indicated. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes.

B. Shop Drawings: For roof specialties. Include plans, elevations, expansion-joint locations, keyed details, and attachments to other work. Distinguish between plant- and field-assembled work. Include the following:

1. Details for expansion and contraction; locations of expansion joints, including direction of expansion and contraction.

2. Pattern of seams and layout of fasteners, cleats, clips, and other attachments. 3. Details of termination points and assemblies, including fixed points. 4. Details of special conditions.

C. Samples for Initial Selection: For each type of roof specialty indicated with factory-applied color finishes.

D. Samples for Verification: For copings, roof-edge flashings, roof-edge drainage systems, and reglets and counterflashings made from 12-inch lengths of full-size components including fasteners, cover joints, accessories, and attachments.

E. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, for copings and roof-edge flashings.

F. Warranty: Sample of special warranty.


A. Do not store roof specialties in contact with other materials that might cause staining, denting, or other surface damage. Store roof specialties away from uncured concrete and masonry.

B. Protect strippable protective covering on roof specialties from exposure to sunlight and high humidity, except to extent necessary for the period of roof specialties installation.

1.6 WARRANTY

A. Special Warranty on Painted Finishes: Manufacturer's standard form in which manufacturer agrees to repair finish or replace roof specialties that show evidence of deterioration of factory-applied finishes within specified warranty period.

1. Fluoropolymer Finish: Deterioration includes, but is not limited to, the following:

a. Color fading more than 5 Hunter units when tested according to ASTM D 2244. b. Chalking in excess of a No. 8 rating when tested according to ASTM D 4214. c. Cracking, checking, peeling, or failure of paint to adhere to bare metal.

2. Finish Warranty Period: 20 years from date of Substantial Completion.

ROOF SPECIALTIES

PART 2 - PRODUCTS

2.1 EXPOSED METALS

A. Aluminum Sheet: ASTM B 209, alloy as standard with manufacturer for finish required, with temper to suit forming operations and performance required.

1. Surface: Smooth, flat finish. 2. Mill Finish: As manufactured. 3. Exposed Coil-Coated Finishes: Prepare, pretreat, and apply coating to exposed metal

surfaces to comply with coating and resin manufacturers' written instructions.

a. Two-Coat Fluoropolymer: AAMA 620. System consisting of primer and fluoropolymer color topcoat containing not less than 70 percent PVDF resin by weight.

B. Aluminum Extrusions: ASTM B 221, alloy and temper recommended by manufacturer for type of use and finish indicated, finished as follows:

1. Exposed High-Performance Organic Finish: Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


C. Stainless-Steel Sheet: ASTM A 240/A 240M or ASTM A 666, Type 304.

D. Zinc-Coated (Galvanized) Steel Sheet: ASTM A 653/A 653M, G90 coating designation.

1. Surface: Smooth, flat finish. 2. Exposed Coil-Coated Finishes: Prepainted by the coil-coating process to comply with

ASTM A 755/A 755M. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


2.2 CONCEALED METALS

A. Aluminum Sheet: ASTM B 209, alloy and temper recommended by manufacturer for type of use and structural performance indicated, mill finished.

B. Aluminum Extrusions: ASTM B 221, alloy and temper recommended by manufacturer for type of use and structural performance indicated, mill finished.

C. Stainless-Steel Sheet: ASTM A 240/A 240M or ASTM A 666, Type 304.

D. Zinc-Coated (Galvanized) Steel Sheet: ASTM A 653/A 653M, G90 coating designation.

ROOF SPECIALTIES


A. Self-Adhering, High-Temperature Sheet: Minimum 30 to 40 mils thick, consisting of slip-resisting polyethylene-film top surface laminated to layer of butyl or SBS-modified asphalt adhesive, with release-paper backing; cold applied. Provide primer when recommended by underlayment manufacturer.

1. Thermal Stability: ASTM D 1970; stable after testing at 240 deg F. 2. Low-Temperature Flexibility: ASTM D 1970; passes after testing at minus 20 deg F. 3. Products: Subject to compliance with requirements, provide one of the following:

a. Carlisle Coatings & Waterproofing; CCW WIP 300HT. b. Grace Construction Products, a unit of W. R. Grace & Co.; Ultra. c. Henry Company; Blueskin PE200 HT. d. Metal-Fab Manufacturing, LLC; MetShield. e. Owens Corning; WeatherLock Metal High Temperature Underlayment.

B. Polyethylene Sheet: 6-mil- thick polyethylene sheet complying with ASTM D 4397.

C. Slip Sheet: Building paper, 3-lb/100 sq. ft. minimum, rosin sized.


A. General: Provide materials and types of fasteners, protective coatings, sealants, and other miscellaneous items required by manufacturer for a complete installation.

B. Fasteners: Manufacturer's recommended fasteners, suitable for application and designed to meet performance requirements. Furnish the following unless otherwise indicated:

1. Exposed Penetrating Fasteners: Gasketed screws with hex washer heads matching color of sheet metal.

2. Fasteners for Aluminum: Aluminum or Series 300 stainless steel. 3. Fasteners for Stainless-Steel Sheet: Series 300 stainless steel. 4. Fasteners for Zinc-Coated (Galvanized) Steel Sheet: Series 300 stainless steel or hot-dip

zinc-coated steel according to ASTM A 153/A 153M or ASTM F 2329.

C. Elastomeric Sealant: ASTM C 920, elastomeric silicone polymer sealant of type, grade, class, and use classifications required by roofing-specialty manufacturer for each application.

2.5 ROOF-EDGE FLASHINGS

A. Canted Roof-Edge Fascia: Manufactured, two-piece, roof-edge fascia consisting of snap-on metal fascia cover in section lengths not exceeding 12 feet and a continuous formed galvanized-steel sheet cant, 0.028 inch thick, minimum, with extended vertical leg terminating in a drip-edge cleat. Provide matching corner units.

1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

a. Hickman Company, W. P. b. Metal-Era, Inc.

ROOF SPECIALTIES

c. MM Systems Corporation. d. Firestone Metal Products – Una-Clad. e. Dimensional Metals, Inc.

2. Fascia Cover: Fabricated from the following exposed metal:

a. Formed Aluminum: 0.050 inch thick. b. Extruded Aluminum: Thickness as required to meet performance requirements.

3. Corners: Factory mitered and continuously welded. 4. Splice Plates: Concealed, of same material, finish, and shape as fascia cover. 5. Fascia Accessories: Fascia extenders with continuous hold-down cleats, Wall cap, Soffit

trim, Downspout scuppers with integral conductor head and downspout adapters and perforated screens.

B. Roof-Edge Fascia: Manufactured, two-piece, roof-edge fascia consisting of snap-on metal fascia cover in section lengths not exceeding 12 feet and a continuous formed- or extruded-aluminum anchor bar with integral drip-edge cleat to engage fascia cover. Provide matching corner units.

1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

a. Hickman Company, W. P. b. Metal-Era, Inc. c. Firestone Metal Products, Uni-Clad. d. Dimensional Metals, Inc.

2. Formed Aluminum Sheet Fascia Covers: Aluminum sheet, 0.050 inch (1.27 mm) thick.

a. Surface: Smooth, flat finish. b. Finish: Two-coat fluoropolymer. c. Color: As selected by Architect from manufacturer's full range.

2.6 ROOF-EDGE DRAINAGE SYSTEMS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Hickman Company, W. P. 2. Metal-Era, Inc. 3. MM Systems Corporation. 4. Firestone Metal Products, Uni-Clad. 5. Dimensional Metals, Inc.

B. Gutters: Manufactured in uniform section lengths not exceeding 12 feet, with matching corner units, ends, outlet tubes, and other accessories. Elevate back edge at least 1 inch above front edge. Furnish flat-stock gutter straps, gutter brackets, expansion joints, and expansion-joint covers fabricated from same metal as gutters.

1. Fabricate from the following exposed metal:

ROOF SPECIALTIES

a. Zinc-Coated Steel: Nominal 0.034-inch thickness.

2. Gutter Profile: Style F according to SMACNA's "Architectural Sheet Metal Manual." 3. Corners: Factory mitered and continuously welded. 4. Gutter Supports: Manufacturer's standard supports as selected by Architect with finish

matching the gutters. 5. Gutter Accessories: Wire ball downspout strainer and flat ends.

C. Downspouts: Plain rectangular complete with mitered elbows, manufactured from the following exposed metal. Furnish with metal hangers, from same material as downspouts, and anchors.

1. Zinc-Coated Steel: Nominal 0.034-inch thickness.

D. Conductor Heads: Manufactured conductor heads, each with flanged back and stiffened top edge and of dimensions and shape indicated, complete with outlet tube that nests into upper end of downspout, exterior flange trim, and built-in overflow.

1. Fabricate from the following exposed metal:

a. Zinc-Coated Steel: Nominal 0.028-inch thickness.

E. Splash Pans: Fabricate from the following exposed metal:

1. Stainless Steel: 0.019 inch thick.

F. Aluminum Finish: Two-coat fluoropolymer.

1. Color: Match Architect's sample.

G. Stainless-Steel Finish: No. 2B (bright, cold rolled, unpolished).

H. Zinc-Coated Steel Finish: Two-coat fluoropolymer.

1. Color: Match Architect's sample.

2.7 VINYL SOFFIT PANELS

A. General: Provide factory-formed vinyl soffit panels designed to be installed by lapping and interconnecting side edges of adjacent panels. Include accessories required for weathertight installation.

B. Match profile and material of existing soffit panels.

1. Finish: Match finish and color of existing soffit panels.

C. Perforated panels formed with vertical panel edges and intermediate stiffening ribs symmetrically spaced between panel edges; with flush joint between panels.

1. Basis-0f-Design Product: Subject to compliance with requirements, provide ProVia, or comparable product by one of the following: a. Certainteed b. Norendex

ROOF SPECIALTIES

c. Georgia-Pacific

2. Panel Coverage: match existing. 3. Panel Height: match existing. 4. Panel Design: Perforated for roof ventilation to match existing, where explicable. 5. Miscellaneous trim pieces and supports:

a. Manufacturer’s standard prefinished “J” channel: For use at all perimeters. b. Manufacturer’s standard prefinished “H” channel: For use at corners of soffits,

where soffits change direction. c. Hat-shaped, rigid furring channels, ASTM C645 7/8” deep. Minimum thickness

2.8 GENERAL FINISH REQUIREMENTS

A. Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes.

B. Protect mechanical and painted finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

C. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, to verify actual locations, dimensions, and other conditions affecting performance of the Work.

B. Examine walls, roof edges, and parapets for suitable conditions for roof specialties.

C. Verify that substrate is sound, dry, smooth, clean, sloped for drainage, and securely anchored.

D. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 UNDERLAYMENT INSTALLATION

A. Felt Underlayment: Install with adhesive for temporary anchorage to minimize use of mechanical fasteners under roof specialties. Apply in shingle fashion to shed water, with lapped joints of not less than 2 inches.

B. Self-Adhering Sheet Underlayment: Install wrinkle free. Apply primer if required by underlayment manufacturer. Comply with temperature restrictions of underlayment manufacturer for installation; use primer rather than nails for installing underlayment at low temperatures. Apply in shingle fashion to shed water. Overlap edges not less than 3-1/2 inches. Roll laps with roller. Cover underlayment within 14 days.

ROOF SPECIALTIES

C. Polyethylene Sheet: Install with adhesive for temporary anchorage to minimize use of mechanical fasteners under roof specialties. Apply in shingle fashion to shed water, with lapped and taped joints of not less than 2 inches.

D. Slip Sheet: Install with tape or adhesive for temporary anchorage to minimize use of mechanical fasteners under roof specialties. Apply in shingle fashion to shed water, with lapped joints of not less than 2 inches.


A. General: Install roof specialties according to manufacturer's written instructions. Anchor roof specialties securely in place, with provisions for thermal and structural movement. Use fasteners, solder, protective coatings, separators, sealants, and other miscellaneous items as required to complete roof-specialty systems.

1. Install roof specialties level, plumb, true to line and elevation; with limited oil-canning and without warping, jogs in alignment, buckling, or tool marks.

2. Provide uniform, neat seams with minimum exposure of solder and sealant. 3. Install roof specialties to fit substrates and to result in watertight performance. Verify

shapes and dimensions of surfaces to be covered before manufacture. 4. Torch cutting of roof specialties is not permitted. 5. Do not use graphite pencils to mark metal surfaces.

B. Metal Protection: Protect metals against galvanic action by separating dissimilar metals from contact with each other or with corrosive substrates by painting contact surfaces with bituminous coating or by other permanent separation as recommended by manufacturer.

1. Coat concealed side of uncoated aluminum and stainless-steel roof specialties with bituminous coating where in contact with wood, ferrous metal, or cementitious construction.

2. Underlayment: Where installing metal flashing directly on cementitious or wood substrates, install a course of felt underlayment and cover with a slip sheet, self-adhering, high-temperature sheet underlayment or polyethylene sheet.

3. Bed flanges in thick coat of asphalt roofing cement where required by manufacturers of roof specialties for waterproof performance.

C. Expansion Provisions: Allow for thermal expansion of exposed roof specialties.

1. Space movement joints at a maximum of 12 feet with no joints within 18 inches of corners or intersections unless otherwise shown on Drawings.

2. When ambient temperature at time of installation is between 40 and 70 deg F, set joint members for 50 percent movement each way. Adjust setting proportionately for installation at higher ambient temperatures.

D. Fastener Sizes: Use fasteners of sizes that will penetrate substrate not less than recommended by fastener manufacturer to achieve maximum pull-out resistance.

E. Seal joints with elastomeric sealant as required by roofing-specialty manufacturer.

F. Seal joints as required for watertight construction. Place sealant to be completely concealed in joint. Do not install sealants at temperatures below 40 deg F.

ROOF SPECIALTIES

G. Soldered Joints: Clean surfaces to be soldered, removing oils and foreign matter. Pre-tin edges of sheets to be soldered to a width of 1-1/2 inches except reduce pre-tinning where pre-tinned surface would show in completed Work. Tin edges of uncoated copper sheets using solder for copper. Do not use torches for soldering. Heat surfaces to receive solder and flow solder into joint. Fill joint completely. Completely remove flux and spatter from exposed surfaces.

3.4 ROOF-EDGE FLASHING INSTALLATION

A. Install cleats, cants, and other anchoring and attachment accessories and devices with concealed fasteners.

B. Anchor roof edgings with manufacturer's required devices, fasteners, and fastener spacing to meet performance requirements.

3.5 ROOF-EDGE DRAINAGE-SYSTEM INSTALLATION

A. General: Install components to produce a complete roof-edge drainage system according to manufacturer's written instructions. Coordinate installation of roof perimeter flashing with installation of roof-edge drainage system.

B. Gutters: Join and seal gutter lengths. Allow for thermal expansion. Attach gutters to firmly anchored gutter supports spaced not more than 24 inches apart. Attach ends with rivets and seal with sealant to make watertight. Slope to downspouts.

1. Install gutter with expansion joints at locations indicated but not exceeding 50 feet apart. Install expansion joint caps.

C. Downspouts: Join sections with manufacturer's standard telescoping joints. Provide hangers with fasteners designed to hold downspouts securely to walls and 1 inch away from walls; locate fasteners at top and bottom and at approximately 60 inches o.c.

1. Provide elbows at base of downspout to direct water away from building. 2. Connect downspouts to underground drainage system indicated.

D. Splash Pans: Install where downspouts discharge on low-slope roofs. Set in elastomeric sealant.

E. Conductor Heads: Anchor securely to wall with elevation of conductor top edge 1 inch below scupper discharge.

3.6 VINYL SOFFIT PANEL INSTALLATION

A. Vinyl Soffit Panels: Provide vinyl soffit panels full width of soffits. Install panels perpendicular to support framing.

1. Flash and seal panels with weather closures where vinyl soffit panels meet walls and at perimeter of all openings.

ROOF SPECIALTIES

B. Metal Fascia Panels: align bottom of panels and fasten with blind rivets, bolts, or self-tapping screws. Flash and seal panels with weather closures where fasciae meet soffits, along lower panel edges, and at perimeter of all openings.


A. Clean exposed metal surfaces of substances that interfere with uniform oxidation and weathering.

B. Clean and neutralize flux materials. Clean off excess solder and sealants.

C. Remove temporary protective coverings and strippable films as roof specialties are installed. On completion of installation, clean finished surfaces including removing unused fasteners, metal filings, pop rivet stems, and pieces of flashing. Maintain roof specialties in a clean condition during construction.

D. Replace roof specialties that have been damaged or that cannot be successfully repaired by finish touchup or similar minor repair procedures.


ENTRY DOORS AND FRAMES 08 1113 - 1

SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 08 1113 – ENTRY DOORS AND FRAMES PART 1 - GENERAL


A. Drawings and general provisions of the Contract, including General and Supplemen-

tary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY


1. Exterior entry doors and frames. 2. Fire-rated Garage Man Doors.

1.3 RELATED SECTIONS:

A. Section 08 7100 "Door Hardware".

B. Section 09 9100 "Painting" for field painting hollow metal doors and frames.



1. Include construction details, material descriptions, core descriptions, fire- resistance ratings and finishes.

B. Shop Drawings: Include the following:

1. Elevations of each door type. 2. Details of doors, including vertical- and horizontal-edge details and

metal thicknesses. 3. Frame details for each frame type, including dimensioned profiles and

metal thicknesses. 4. Locations of reinforcement and preparations for hardware. 5. Details of each different wall opening condition. 6. Details of anchorages, joints, field splices, and connections. 7. Details of accessories.

C. Schedule: Provide a schedule of hollow-metal work prepared by or under the supervision

of supplier, using same reference numbers for details and openings as those on Drawings. Coordinate with final Door Hardware Schedule.




A. Product Test Reports: For each type of hollow-metal door and frame assembly, for

tests performed by a qualified testing agency.

B. Oversize Construction Certification: For assemblies required to be fire rated and exceed-ing limitations of labeled assemblies.

1.6 SUBMITTALS

A. Submit MSDS and/or TD sheets with VOC highlighted for each adhesive, sealant, field ap-

plied paint, or field applied coating.

B. Submit a Material Use Confirmation Form (section 018113) for each system with recycled or regional content information when applicable.

1. The form shall include % recycled / % regional content, including material only value.

2. Attach documentation from product manufacturer including recycled con-tent, location of

product manufacturer, and location of raw material extraction for the following materi-als: a. Metal

C. Door hardware supplier is to furnish templates, template reference number and/or physical

hardware to the steel door and frame supplier in order to prepare the doors and frames to receive the finish hardware items.

D. Shop Drawings: Include the following:

1. Elevations of each door design. 2. Details of doors, including vertical and horizontal edge details and

metal thicknesses.

3. Frame details for each frame type, including dimensioned profiles and metal thicknesses.

4. Locations of reinforcement and preparations for hardware. 5. Details of anchorages, joints, field splices, and connections.


A. Source Limitations: Obtain hollow metal doors and frames through one source from a

single manufacturer wherever possible.

B. Quality Standard: In addition to requirements specified, comply with ANSI/SDI A250.8, lat-est edition, "Recommended Specifications for Standard Steel Doors and Frames".

C. Pre-Submittal Conference: Conduct conference with attendance by representatives of Sup-

plier, Installer, and Contractor to review proper methods and procedures for installing hol-low metal doors and frames.




A. Store hollow metal work under cover at Project site. Place in stacks of five units maximum in a vertical position with heads up, spaced by blocking, on minimum 4-inch high wood block-ing. Do not store in a manner that traps excess humidity.

1.9 PROJECT CONDITIONS

A. Field Measurements: Verify actual dimensions of openings by field measurements be-

fore fabrication. 1.10 COORDINATION

A. Coordinate installation of anchorages for hollow metal frames. Furnish setting drawings,

templates, and directions for installing anchorages, including sleeves, concrete inserts, an-chor bolts, and items with integral anchors. Deliver such items to Project site in time for in-stallation.

1.11 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair

or replace doors that fail in materials or workmanship within specified warranty period.

B. Warranty includes installation that may be required due to repair or replacement of defec-tive doors.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Basis-of-Design Product: Subject to compliance with requirements, provide Steelcraft; an Al-

legion brand; “CE16 Series” Six Panel Door, “L16 Series” Flush Door, and “F14 Series” frames or a comparable product by one of the following:

1. Ceco Door; ASSA ABLOY. 2. Curries Company; ASSA ABLOY.

2.2 EXTERIOR ENTRY DOORS AND FRAMES

A. Extra-Heavy-Duty Doors and Frames: SDI A250.8, Level 3. At locations indicated in the Door

and Frame Schedule.

1. Physical Performance: Level A according to SDI A250.4. 2. Doors: CE16 Series – Six Panel Door.

a. Thickness: 1-3/4 inches (44.5 mm.) b. Face: Metallic-coated steel sheet, minimum thickness of 0.053 inch (1.3 mm),

16- gage, with minimum A40 (ZF120) galvanneal coating.

http://www.specagent.com/Lookup?ulid=5745

http://www.specagent.com/Lookup?uid=123457006328







c. Edge Construction: Model 1, Full Flush. d. Core: Polystyrene.

3. Frames: F14 Series

a. Materials: Metallic-coated steel sheet, minimum thickness of 0.067 inch (1.7

mm), 14 gage, with minimum A40 (ZF120) galvanneal coating. b. Construction: Knocked down with double rabbet.

4. Exposed Finish: Prime.

c. Fire-Rated Core: Manufacturer's standard core for fire-rated and temperature-rise-rated doors. Used where listed to be replaced in the unit schedule. Match existing fire rating.

2.3 FRAME ANCHORS

A. Jamb Anchors:

1. Stud-Wall Type: Designed to engage stud, welded to back of frames; not less than 0.042 inch (1.0 mm) thick.

B. Floor Anchors: Formed from same material as frames, minimum thickness of 0.042 inch

(1.0 mm), and as follows:

1. Monolithic Concrete Slabs: Clip-type anchors, with two holes to receive fas-teners.

2.4 MATERIALS

A. Recycled Content of Steel Products: Postconsumer recycled content plus one-half

of preconsumer recycled content not less than 25%.

B. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, Commercial Steel (CS), Type B; suitable for exposed applications.

C. Metallic-Coated Steel Sheet: ASTM A 653/A 653M, Commercial Steel (CS), Type B.

D. Frame Anchors: ASTM A 879/A 879M, Commercial Steel (CS), 04Z (12G)

coating designation; mill phosphatized.

1. For anchors built into exterior walls, steel sheet complying with ASTM A 1008/A 1008M or ASTM A 1011/A 1011M, hot-dip galvanized ac-cording to ASTM A 153/A 153M, Class B.

E. Inserts, Bolts, and Fasteners: Hot-dip galvanized according to ASTM A 153/A 153M.

2.5 FABRICATION

A. Fabricate hollow-metal work to be rigid and free of defects, warp, or buckle. Accurately



form metal to required sizes and profiles, with minimum radius for metal thickness. Where practical, fit and assemble units in manufacturer's plant. To ensure proper assembly at Pro-ject site, clearly identify work that cannot be permanently factory assembled before ship-ment.

B. Tolerances: Fabricate hollow metal work to tolerances indicated in ANSI/SDI A250.8.

C. Hollow-Metal Doors:

1. Vertical Edges for Single-Acting Doors: Provide beveled or square edges

at manufacturer's discretion. 2. Top Edge Closures: Close top edges of doors with flush closures of

same material as face sheets.

3. Bottom Edge Closures: Close bottom edges of doors where required for attachment of weather stripping with end closures or channels of same ma-terial as face sheets.

4. Exterior Doors: Provide weep-hole openings in bottoms of exterior doors to permit moisture to escape. Seal joints in top edges of doors against water penetration.

D. Hollow-Metal Frames: Where frames are fabricated in sections due to shipping or han-dling limitations, provide alignment plates or angles at each joint, fabricated of same thick-ness metal as frames.

1. Frames: Provide closed tubular members with no visible face seams or

joints, fabricated from same material as door frame. Fasten members at crossings and to jambs by butt welding.

2. Provide countersunk, flat-head concealed bolts. 3. Provide frames with existing wall anchor. 4. Floor Anchors: Weld anchors to bottoms of jambs with at least four spot

welds per anchor. 5. Jamb Anchors: Provide number and spacing of anchors in accordance

with manufacturer’s recommendations for in-place existing construction and as indicated as follows:

a. Stud-Wall Type: Locate anchors not more than 18 inches (457 mm) from top

and bottom of frame. Space anchors not more than 32 inches (813 mm) o.c. and as follows:

1) Three anchors per jamb up to 60 inches (1524 mm) high. 2) Four anchors per jamb from 60 to 90 inches (1524 to 2286 mm) high. 3) Five anchors per jamb from 90 to 96 inches (2286 to 2438 mm) high. 4) Five anchors per jamb plus one additional anchor per jamb for each

24 inches (610 mm) or fraction thereof above 96 inches (2438 mm) high.

6. Head Anchors: Two anchors per head for frames more than 42 inches (1067 mm) wide and mounted in metal-stud partitions.



7. Door Silencers: Except on weather-stripped frames, drill stops to receive door silencers as follows. Keep holes clear during construction. Silencers shall be furnished by frame manufacturer.

a. Single-Door Frames: Drill stop in strike jamb to receive three door silencers. b. Double-Door Frames: Drill stop in head jamb to receive two door silencers.

8. Provide gasketed astragals for exterior pairs of doors.

E. Hardware Preparation: Factory prepare hollow-metal work to receive templated mortised

hardware; include cutouts, reinforcement, mortising, drilling, and tapping according to SDI A250.6, the Door Hardware Schedule, and templates.

1. Reinforce doors and frames to receive nontemplated, mortised, and sur-

face- mounted door hardware. 2. Comply with applicable requirements in SDI A250.6 and BHMA A156.115 for

preparation of hollow-metal work for hardware. 3. Comply with applicable requirements in ANSI/SDI A250.6 and ANSI/DHI

A115 Series specifications for preparation of hollow metal work for hardware.

F. Fabricate concealed stiffeners and edge channels from either cold-or-hot rolled sheet steel. 2.6 STEEL FINISHES

A. Prime Finishes: Doors and frames shall be cleaned, and chemically treated in ensure maxi-

mum finish paint adhesion. Surfaces of the door and frame exposed to view shall receive a factory applied coat of rust inhibiting shop primer.

1. Shop Primer: Manufacturer's standard, fast-curing, lead- and chromate-free

primer complying with SDI A250.10; recommended by primer manufac-turer for substrate; compatible with substrate and field-applied coatings de-spite prolonged exposure.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with

requirements for installation tolerances and other conditions affecting performance of the Work.

B. Examine roughing-in for embedded and built-in anchors to verify actual locations before

frame installation.

C. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work.




3.2 PREPARATION

A. Drill and tap doors and frames to receive nontemplated, mortised, and surface-mounted

door hardware. 3.3 INSTALLATION

A. General: Install hollow-metal work plumb, rigid, properly aligned, and securely fastened

in place. Comply with Drawings and manufacturer's written instructions.

B. Hollow-Metal Frames: Install hollow-metal frames for doors, transoms, sidelites, bor-rowed lites, and other openings, of size and profile indicated. Comply with SDI A250.11 or as required by standards specified.

1. Set frames accurately in position; plumbed, aligned, and braced securely

until permanent anchors are set. After wall construction is complete, re-move temporary braces, leaving surfaces smooth and undamaged.

a. Where frames are fabricated in sections because of shipping or handling

limitations, field splice at approved locations by welding face joint continuous-ly; grind, fill, dress, and make splice smooth, flush, and invisible on exposed fac-es.

b. Remove temporary braces necessary for installation only after frames have been properly set and secured.

c. Check plumb, square, and twist of frames as walls are constructed. Shim as necessary to comply with installation tolerances.

2. Floor Anchors: Provide floor anchors for each jamb and mullion that extends

to floor, and secure with postinstalled expansion anchors. 3. Installation Tolerances: Adjust hollow-metal door frames for square-

ness, alignment, twist, and plumb to the following tolerances:

a. Squareness: Plus or minus 1/16 inch (1.6 mm), measured at door rabbet on a line 90 degrees from jamb perpendicular to frame head.

b. Alignment: Plus or minus 1/16 inch (1.6 mm), measured at jambs on a hori-zontal line parallel to plane of wall.

c. Twist: Plus or minus 1/16 inch (1.6 mm), measured at opposite face corners of jambs on parallel lines, and perpendicular to plane of wall.

d. Plumbness: Plus or minus 1/16 inch (1.6 mm), measured at jambs at floor.

C. Hollow-Metal Doors: Fit hollow-metal doors accurately in frames, within clearances speci-fied below. Shim as necessary.

1. Non-Fire-Rated Steel Doors:

a. Between Door and Frame Jambs and Head: 1/8 inch (3.2 mm) plus or minus

1/32 inch (0.8 mm).



b. Between Edges of Pairs of Doors: 1/8 inch (3.2 mm) to 1/4 inch (6.3 mm) plus or minus 1/32 inch (0.8 mm).

c. At Bottom of Door: 5/8 inch (15.8 mm) plus or minus 1/32 inch (0.8 mm). d. Between Door Face and Stop: 1/16 inch (1.6 mm) to 1/8 inch (3.2 mm) plus

or minus 1/32 inch (0.8 mm). 3.4 ADJUSTING AND CLEANING

A. Final Adjustments: Check and readjust operating hardware items immediately before final

inspection. Leave work in complete and proper operating condition. Remove and replace de-fective work, including hollow-metal work that is warped, bowed, or otherwise unacceptable.

B. Prime-Coat Touchup: Immediately after erection, sand smooth rusted or damaged areas

of prime coat and apply touchup of compatible air-drying, rust-inhibitive primer. END OF SECTION 08 1113

METAL STORM DOORS 08 1163.23 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 08 1163.23 – METAL STORM DOORS

PART 1 - GENERAL



1.2 SUMMARY

A. Section includes storm doors for exterior locations.



1. Include construction details, material descriptions, fabrication methods, dimensions of individual components and profiles, hardware, finishes, and operating instructions.

B. Shop Drawings: For storm doors.

1. Include plans, elevations, sections, and details. 2. Detail attachments to other work, and between units, if any. 3. Include hardware and required clearances.

C. Samples for Initial Selection: For each type of stormdoor indicated.

1. Include Samples of hardware and accessories involving color selection.


A. Qualification Data: For manufacturer and testing agency.

B. Product Test Reports: For each stormdoor, for tests performed by a qualified testing agency, and for each class and performance grade indicated, tested at AAMA gateway size.


A. Manufacturer Qualifications: A manufacturer capable of fabricating storm doors that meet or exceed performance requirements indicated and of documenting this performance by inclusion in lists and by labels, test reports, and calculations.

B. Installer Qualifications: An installer acceptable to stormdoor manufacturer for installation of units required for this Project.


1.6 WARRANTY

A. Manufacturer's Special Warranty: Manufacturer agrees to repair or replace components of storm doors that fail in materials or workmanship within specified warranty period.


a. Failure to meet performance requirements. b. Structural failures including excessive deflection. c. Excessive water leakage or air infiltration. d. Faulty operation of movable panels and hardware. e. Deterioration of metals, metal finishes, and other materials beyond normal

weathering. f. Failure of insulating glass.

2. Warranty Period:

a. Sliding Door: Three years from date of Substantial Completion. b. Insulating-Glass Units: 10 years from date of Substantial Completion. c. Aluminum Finish: Five years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: 1. Lansing Housing Products Model 500 (Basis of Design) 2. Wayne Door 3. Larson Doors

B. Source Limitations: Obtain storm doors from single source from single manufacturer.

2.2 ALUMINUM STORM DOORS

A. GENERAL 1. Materials - The master frame shall be of roll formed, tubular, lock-seam construction

formed from 22 gauge hot-dipped, zinc impregnated, galvannealed steel. All roll formed profiles shall be engineered with specific and exclusive use as component parts for door fabrication.

2. Frame liners and door sweeps shall be formed from 6063-T5 aluminum. 3. The kick panel shall be of 18 gauge galvannealed sheet steel, embossed for added

rigidity. 4. Frame liner shall be of extruded aluminum. The head and side frame liners shall be

designed to receive a flexible weather seal for protection against inclement weather and dust infiltration. A magnetic weather seal shall be available when specified. The head frame liner shall be so designed and extruded to also function as a drip cap over the top of the door.


5. The door shall be manufactured with not less than four (4) hinges. Leaf hinges shall be 430 stainless steel alloy, .072 wall thickness and shall be integrally assembled into the Z-bar frame liner with stainless steel pins pivoting on oil-lite bronze bushings.

6. The bottom of the doors shall have an aluminum extrusion that will accept a durable vinyl plastic door sweep, adjustable to a minimum of one (1) inch.

B. CONSTRUCTION 1. The hollow master frame of the door shall be of miter joint construction, rigidly fastened

with 16 gauge gussets. The corners are uniformly welded on both the inside and the outside edge.

2. The transom rail shall be of roll-formed tubular, lock seam, 22 gauge galvannealed steel, accurately machined to fit the frame and rigidly affixed to both sides of the door. The kick plate(s) shall be form fitted and secured at the top and bottom. 18 gauge spline shall be attached on both sides of kick plate(s) for added rigidity.

3. The tempered safety glass steel insert frames shall be of mitered joint construction, machine fitted and fastened at each corner by staking into die cast corner gussets.

4. Glazing shall be of virgin polyvinyl plastic to permit easy replacement of glass. Weatherstripping shall be used to prevent rattle and insect passage as well as to provide for positive contact between inserts and main frame.

5. The lower glass insert shall move up and down with multi-stop positions for desired air infiltration. Both upper and lower sashes will overlap each other at the meeting rail.

C. SCREENING 1. Screen frames shall be of rolled, tubular lock seam construction, formed from not less

than 25 gauge hot dipped galvannealed steel. They shall be of miter joint construction and made rigid at the corners by staking in to metal corner gussets.

2. Stainless steel wire mesh of .018 diameter shall be made an integral part of the screen insert as required. Material shall be alloy 304 stainless steel.

D. FINISH 1. All exposed surfaces of all metal parts shall be free of surface blemishes. All sections

either assembled or fabricated in factory, shall have 4 wash coats and finish coat applied after such assembly or fabrication is completed.

2. All mainframe Miter welded corners shall be pre-treated with a rust inhibitor prior to powder coat painting.

3. All prefinish treatments and wash coats shall be bake oven processed at 400 degrees F. Air-dry finish shall be unacceptable as offering an inferior finish for high density usage.

4. All exposed areas of stainless wire cloth and frames shall have a chemical pre-treatment process applied, with a finish of polyester powder coat paint, electrostatically applied, and cured to a hard durable finish. Powder coat paint finish shall be a minimum of 1.5 mil thickness.

E. GLAZING 1. Glass and Glazing: Manufacturer's standard glazing system that produces weathertight

seal. Comply with requirements for windborne-debris resistance. 2. Glass: ASTM C 1036, Type 1, q3, Category II safety glass complying with testing

requirements in 16 CFR 1201. 3. Safety Glazing Labeling: Permanently mark safety glazing with certification label of the

SGCC. Label shall indicate manufacturer's name, type of glass, thickness, and safety glazing standard with which glass complies.

4. Tint: Clear.


2.3 FABRICATION

A. Fabricate storm doors in sizes indicated. Include a complete system for assembling components and anchoring doors.

B. Fabricate storm doors that are reglazable without dismantling panel framing.

C. Weather Stripping: Provide full-perimeter weather stripping for each door panel.

D. Complete fabrication, assembly, finishing, hardware application, and other work in the factory to greatest extent possible. Disassemble components only as necessary for shipment and installation.



B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

C. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast.

2.5 ALUMINUM FINISHES

A. Clear Anodic Finish: AAMA 611, AA-M12C22A41, Class I, 0.018 mm or thicker.

B. Color Anodic Finish: AAMA 611, AA-M12C22A42/A44, Class I, 0.018 mm or thicker. 1. Color: As selected by Architect from full range of industry colors and color densities.

C. Baked-Enamel or Powder-Coat Finish: AAMA 2603 except with a minimum dry film thickness of 1.5 mils (0.04 mm). Comply with coating manufacturer's written instructions for cleaning, conversion coating, and applying and baking finish.

1. Color and Gloss: As selected by Architect from manufacturer's full range.

D. High-Performance Organic Finish: Two-coat fluoropolymer finish complying with AAMA 2604 and containing not less than 50 percent PVDF resin by weight in color coat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


E. High-Performance Organic Finish: Three-coat fluoropolymer finish complying with AAMA 2605 and containing not less than 50 percent PVDF resin by weight in both color coat and clear


topcoat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine openings, substrates, structural support, anchorage, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.

B. Verify rough opening dimensions, levelness of threshold substrate, and operational clearances.

C. Examine wall flashings, vapor retarders, water and weather barriers, and other built-in components to ensure a coordinated, weathertight storm door installation.


3.2 INSTALLATION

A. Comply with Drawings, Shop Drawings, and manufacturer's written instructions for installing doors, hardware, accessories, and other components.

B. Windborne Debris Resistance: Anchor storm doors that have been tested for windborne debris resistance to structure using anchoring method, fastener type, and fastening frequency identical to that used in windborne debris resistance testing.

C. Install storm doors level, plumb, square, true to line, without distortion, without warp or rack of frames and panels, and without impeding thermal movement; anchored securely in place to structural support; and in proper relation to wall flashing, vapor retarders, air barriers, water/weather barriers, and other adjacent construction.

D. Set sill members in bed of sealant or with gaskets, as indicated, to provide weathertight construction.

E. Install storm doors and components to drain condensation, water penetrating joints, and moisture migrating within doors to the exterior.

F. Separate aluminum and other corrodible surfaces from sources of corrosion or electrolytic action at points of contact with other materials.

3.3 FIELD QUALITY CONTROL

A. Test and inspect installed storm doors as follows:


1. Testing Methodology: Test storm doors for air infiltration and water resistance according to AAMA 502.

2. Air-Infiltration Testing:

a. Test Pressure: That required to determine compliance with AAMA/WDMA/CSA 101/I.S.2/A440 performance class indicated.

b. Allowable Air-Leakage Rate: 1.5 times the applicable AAMA/WDMA/CSA 101/I.S.2/A440 rate for product type and performance class rounded down to one decimal place.

3. Water-Resistance Testing:

a. Test Pressure: Two-thirds times test pressure required to determine compliance with AAMA/WDMA/CSA 101/I.S.2/A440 performance grade indicated.

b. Allowable Water Infiltration: No water penetration.

4. Testing Extent: Three storm doors of each type as selected by Architect and a qualified independent testing and inspecting agency. Conduct tests after perimeter sealants have cured.

5. Test Reports: Prepared according to AAMA 502.

B. Stormdoor will be considered defective if it does not pass tests and inspections.

3.4 ADJUSTING, CLEANING, AND PROTECTION

A. Lubricate hardware and moving parts.

B. Adjust operating panels and screens to provide a tight fit at contact points and weather stripping for smooth operation, without binding, and a weathertight closure. Adjust hardware for proper alignment, smooth operation, and proper latching without unnecessary force or excessive clearance.

C. Clean exposed surfaces immediately after installing storm doors. Avoid damaging protective coatings and finishes. Remove nonpermanent labels, excess sealants, glazing materials, dirt, and other substances.

D. Remove and replace glass that has been broken, chipped, cracked, abraded, or damaged during construction period.

E. Protect stormdoor surfaces from contact with contaminating substances resulting from construction operations. If contaminating substances contact stormdoor surfaces, remove contaminants immediately according to manufacturer's written instructions.

F. Refinish or replace storm doors with damaged finishes.

G. Replace damaged components.


SOLID CORE WOOD DOORS 08 1423 - 1 SMHA Scattered Site Renovation 2017349.01

March 01, 2017

SECTION 081 423 – SOLID CORE WOOD DOORS PART 1 - GENERAL


A. Drawings and general provisions of the Contract, including General and Supplemen-tary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY


1. Solid core prehung wood doors.

1.3 SUBMITTALS

A. Product Data: For each type of product indicated. Include construction details, material de-scriptions, core descriptions, hardware reinforcements, profiles, anchors, fire-resistance rat-ing, and finishes.

1.4 GREEN COMMUNITY SUBMITTALS

A. Submit MSDS and/or TD sheets with VOC highlighted for each adhesive, sealant, field ap-plied paint, or field applied coating.

B. Door hardware supplier is to furnish templates, template reference number and/or physical hardware to the door supplier in order to prepare the doors to receive the finish hardware items.

C. Shop Drawings: Include the following:

1. Elevations of each door design. 2. Details of doors, including vertical and horizontal edge details and thicknesses. 3. Locations of reinforcement and preparations for hardware. 4. Louver blade and frame sections 6-inches long, each material and finish.


A. Source Limitations: Obtain doors through one source from a single manufacturer wher-ever possible.

B. Pre-Submittal Conference: Conduct conference in compliance with requirements in Division

01 Section "Project Meetings" with attendance by representatives of Supplier, Installer, and Contractor to review proper methods and procedures for installing doors.


March 01, 2017


A. Deliver doors palletized, wrapped, or crated to provide protection during transit and Project

site storage. Do not use non-vented plastic. Store till ready for construction.


A. Field Measurements: Verify actual dimensions of openings by field measurements before fab-rication.

1.8 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace doors that fail in materials or workmanship within specified warranty period.

B. Warranty includes installation and finishing that may be required due to repair or replace-

ment of defective doors. PART 2 - GENERAL

2.1 MANUFACTURERS

A. Basis of Design Product: Subject to compliance with requirements, provide Jeld-Wen; Pro-

core or comparable product by one of the following:

1. Masonite International Corp. 2. Lynden Door, Inc.

B. Door Design: Match Existing.

1. Surface Finish: Woodgrain Surface.

a. Panels and Sticking Profile: Prefinished raised six panel, with modified cove bead-ed sticking.

C. Core and Frame

1. Solid core: Wood/MDF with all wood frame.

a. Thickness: Not less than 1-3/8 inches.

b. Blocking: Provide behind panels for support.

c. Provide prehung frame to match existing building.

D. manufacturer's standard primed finish doors.

E. Factory machine doors for hardware. Refer to Section 087100 “Door Hardware” for

door hardware to be installed in hollow core doors. Hardware finish to match existing build-ing.


March 01, 2017

F. Hinges: Provide manufacturer’s standard hinges for prehung doors. Finish shall match existing.

PART 3 - EXECUTION

3.1 INSTALLATION

A. General: Install hollow core door work plumb, rigid, properly aligned, and securely fastened

in place; comply with Drawings and manufacturer's written instructions.

B. Comply with WDMA's "How to Store, Handle, Finish, Install, and Maintain Wood Doors."

C. Align and fit doors in frames with uniform clearances and bevels. Machine doors for hardware. Seal cut surfaces after fitting and machining.

3.2 ADJUSTING AND CLEANING

A. Final Adjustments: Check and readjust operating hardware items immediately before final

inspection. Leave work in complete and proper operating condition. Remove and replace de-fective work or otherwise unacceptable.


SLIDING ALUMINUM_FRAMED GLASS DOORS 08 3213 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 08 3213 - SLIDING ALUMINUM-FRAMED GLASS DOORS

PART 1 - GENERAL



1.2 SUMMARY

A. Section includes sliding aluminum-framed glass doors for exterior locations.



1. Include construction details, material descriptions, fabrication methods, dimensions of individual components and profiles, hardware, finishes, and operating instructions.

B. Shop Drawings: For sliding aluminum-framed glass doors.

1. Include plans, elevations, sections, and details. 2. Detail attachments to other work, and between units, if any. 3. Include hardware and required clearances.

C. Samples for Initial Selection: For each type of sliding aluminum-framed glass door indicated.

1. Include Samples of hardware and accessories involving color selection.


A. Qualification Data: For manufacturer and testing agency.

B. Product Test Reports: For each sliding aluminum-framed glass door, for tests performed by a qualified testing agency, and for each class and performance grade indicated, tested at AAMA gateway size.


A. Manufacturer Qualifications: A manufacturer capable of fabricating sliding aluminum-framed glass doors that meet or exceed performance requirements indicated and of documenting this performance by inclusion in lists and by labels, test reports, and calculations.


B. Installer Qualifications: An installer acceptable to sliding aluminum-framed glass door manufacturer for installation of units required for this Project.

1.6 WARRANTY

A. Manufacturer's Special Warranty: Manufacturer agrees to repair or replace components of sliding aluminum-framed glass doors that fail in materials or workmanship within specified warranty period.


a. Failure to meet performance requirements. b. Structural failures including excessive deflection. c. Excessive water leakage or air infiltration. d. Faulty operation of movable panels and hardware. e. Deterioration of metals, metal finishes, and other materials beyond normal

weathering. f. Failure of insulating glass.

2. Warranty Period:

a. Sliding Door: Three years from date of Substantial Completion. b. Insulating-Glass Units: 10 years from date of Substantial Completion. c. Aluminum Finish: Five years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: 1. Pella 2. Jeld-wen 3. Marvin 4. CMD Group

B. Source Limitations: Obtain sliding aluminum-framed glass doors from single source from single manufacturer.


A. Product Standard: Comply with AAMA/WDMA/CSA 101/I.S.2/A440 for minimum standards of performance, materials, components, accessories, and fabrication unless more stringent requirements are indicated.

1. Product Certification: AAMA certified with label attached to each door.

B. Performance Class and Grade: AAMA/WDMA/CSA 101/I.S.2/A440 as follows:


1. Minimum Performance Class: Class R. 2. Minimum Performance Grade: Grade 15.

C. Thermal Transmittance: NFRC 100 maximum total fenestration product U-factor of 0.32 Btu/sq. ft. x h x deg F (1.83 W/sq. m x K).

D. Solar Heat-Gain Coefficient (SHGC): NFRC 200 maximum total fenestration product SHGC of 0.30.

E. Condensation-Resistance Factor (CRF): Provide sliding aluminum-framed glass doors tested for thermal performance according to AAMA 1503, showing a CRF of 45.

F. Thermal Movements: Provide sliding aluminum-framed glass doors, including anchorage, that allow for thermal movements resulting from the following maximum change (range) in ambient and surface temperatures by preventing buckling, opening of joints, overstressing of components, failure of joint sealants, failure of connections, and other detrimental effects. Base engineering calculation on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss.

1. Temperature Change (Range): 120 deg F (67 deg C), ambient; 180 deg F (100 deg C, material surfaces.

G. Sound Transmission Class (STC): Rated for not less than 28 STC when tested for laboratory sound transmission loss according to ASTM E 90 and determined by ASTM E 413.

H. Outside-Inside Transmission Class (OITC): Rated for not less than 23 OITC when tested for laboratory sound transmission loss according to ASTM E 90 and determined by ASTM E 1332.

I. Windborne-Debris-Impact Resistance: Sliding aluminum-framed glass doors shall comply with basic protection testing requirements in ASTM E 1996 for Wind Zone 1 when tested according to ASTM E 1886. Test specimens shall be no smaller in width and length than doors indicated for use on Project.

1. Large-Missile Test: For glazing located within 30 feet (9.1 m) of grade. 2. Small-Missile Test: For glazing located more than 30 feet (9.1 m) above grade.

2.3 SLIDING ALUMINUM-FRAMED GLASS DOORS

A. Frames and Door Panels: Fabricated from aluminum extrusions complying with AAMA/WDMA/CSA 101/I.S.2/A440.

1. Thermally Improved Construction: Fabricate frames and door panels with an integral, concealed, low-conductance thermal barrier located between exterior and interior surfaces in a manner that eliminates direct metal-to-metal contact..

B. Threshold and Sill Cap/Track: Provide extruded-aluminum threshold and track of thickness, dimensions, and profile indicated; designed to comply with performance requirements indicated and to drain to the exterior; with manufacturer's standard finish.

1. Low-Profile Floor Track: ADA-ABA compliant.


2.4 GLAZING

A. Glass and Glazing: Manufacturer's standard glazing system that produces weathertight seal. Comply with requirements for windborne-debris resistance.

1. Glass: ASTM C 1036, Type 1, q3, Category II safety glass complying with testing requirements in 16 CFR 1201.

2. Safety Glazing Labeling: Permanently mark safety glazing with certification label of the SGCC. Label shall indicate manufacturer's name, type of glass, thickness, and safety glazing standard with which glass complies.

3. Tint: Clear. 4. Insulating-Glass Units: ASTM E 2190, certified through IGCC as complying with

requirements of IGCC.

a. Filling: Fill space between glass lites with argon. b. Low-E Coating: Manufacturer's standard.

2.5 HARDWARE

A. General: Provide manufacturer's standard hardware, fabricated from a corrosion-resistant material compatible with aluminum complying with AAMA 907 and designed to smoothly operate, tightly close, and securely lock sliding aluminum-framed glass doors.

B. Door Pulls: Provide manufacturer's standard pull.

1. Color and Finish: As selected by Architect from manufacturer's full range.

C. Lock: Install manufacturer's keyed cylinder lock on each movable panel, lockable from the inside only. Adjust locking device to allow unobstructed movement of the panel across adjacent panel in the direction indicated.

1. Keying System: Keyed to match other building entrances.

2.6 INSECT SCREENS

A. General: Design sliding aluminum-framed glass doors to accommodate screens in a tight-fitting, removable arrangement, fully integrated with door frame. Provide screen for each operable door panel.

B. Aluminum Frames: Manufacturer's standard extruded aluminum profile fabricated from aluminum alloy complying with SMA 1201 and finished to match door frame. Fabricate frames with mitered or coped joints or corner extrusions, concealed fasteners, and removable PVC spline/anchor concealing edge of frame.

C. Hardware: Manufacturer's standard noncorrosive metal.

1. Lock: Manufacturer's standard pull and keyless locking device on each movable panel, lockable from inside only, designed to allow unobstructed movement of panel across adjacent panel.


2.7 ACCESSORIES

A. Fasteners: Noncorrosive and compatible with door members, trim, hardware, anchors, and other components.

1. Exposed Fasteners: Do not use exposed fasteners to the greatest extent possible. For application of hardware, use fasteners that match finish hardware being fastened.

B. Anchors, Clips, and Accessories: Provide anchors, clips, and accessories of aluminum, nonmagnetic stainless steel, or zinc-coated steel or iron for sliding aluminum-framed glass doors, complying with ASTM B 456 or ASTM B 633 for SC 3 severe service conditions; provide sufficient strength to withstand design pressure indicated.

1. Windborne-Debris Resistance: Provide anchors of same design used in windborne-debris resistance testing.

2.8 FABRICATION

A. Fabricate sliding aluminum-framed glass doors in sizes indicated. Include a complete system for assembling components and anchoring doors.

B. Fabricate sliding aluminum-framed glass doors that are reglazable without dismantling panel framing.

C. Weather Stripping: Provide full-perimeter weather stripping for each door panel.

D. Weep Holes: Provide weep holes and internal drainage passages to conduct infiltrating water to exterior.

E. Complete fabrication, assembly, finishing, hardware application, and other work in the factory to greatest extent possible. Disassemble components only as necessary for shipment and installation.

F. Factory-Glazed Fabrication: Glaze sliding aluminum-framed glass doors in the factory where practical and possible for applications indicated. Comply with requirements in Section 088000 "Glazing" and with AAMA/WDMA/CSA 101/I.S.2/A440.



B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

C. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast.


2.10 ALUMINUM FINISHES

A. Clear Anodic Finish: AAMA 611, AA-M12C22A41, Class I, 0.018 mm or thicker.

B. Color Anodic Finish: AAMA 611, AA-M12C22A42/A44, Class I, 0.018 mm or thicker. 1. Color: As selected by Architect from full range of industry colors and color densities.

C. Baked-Enamel or Powder-Coat Finish: AAMA 2603 except with a minimum dry film thickness of 1.5 mils (0.04 mm). Comply with coating manufacturer's written instructions for cleaning, conversion coating, and applying and baking finish.


D. High-Performance Organic Finish: Two-coat fluoropolymer finish complying with AAMA 2604 and containing not less than 50 percent PVDF resin by weight in color coat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


E. High-Performance Organic Finish: Three-coat fluoropolymer finish complying with AAMA 2605 and containing not less than 50 percent PVDF resin by weight in both color coat and clear topcoat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions.


PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine openings, substrates, structural support, anchorage, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.

B. Verify rough opening dimensions, levelness of threshold substrate, and operational clearances.

C. Examine wall flashings, vapor retarders, water and weather barriers, and other built-in components to ensure a coordinated, weathertight sliding aluminum-framed glass door installation.


3.2 INSTALLATION

A. Comply with Drawings, Shop Drawings, and manufacturer's written instructions for installing doors, hardware, accessories, and other components.


B. Windborne Debris Resistance: Anchor sliding aluminum-framed glass doors that have been tested for windborne debris resistance to structure using anchoring method, fastener type, and fastening frequency identical to that used in windborne debris resistance testing.

C. Install sliding aluminum-framed glass doors level, plumb, square, true to line, without distortion, without warp or rack of frames and panels, and without impeding thermal movement; anchored securely in place to structural support; and in proper relation to wall flashing, vapor retarders, air barriers, water/weather barriers, and other adjacent construction.

D. Set sill members in bed of sealant or with gaskets, as indicated, to provide weathertight construction.

E. Install sliding aluminum-framed glass doors and components to drain condensation, water penetrating joints, and moisture migrating within doors to the exterior.

F. Separate aluminum and other corrodible surfaces from sources of corrosion or electrolytic action at points of contact with other materials.


A. Test and inspect installed sliding aluminum-framed glass doors as follows:

1. Testing Methodology: Test sliding aluminum-framed glass doors for air infiltration and water resistance according to AAMA 502.

2. Air-Infiltration Testing:

a. Test Pressure: That required to determine compliance with AAMA/WDMA/CSA 101/I.S.2/A440 performance class indicated.

b. Allowable Air-Leakage Rate: 1.5 times the applicable AAMA/WDMA/CSA 101/I.S.2/A440 rate for product type and performance class rounded down to one decimal place.

3. Water-Resistance Testing:

a. Test Pressure: Two-thirds times test pressure required to determine compliance with AAMA/WDMA/CSA 101/I.S.2/A440 performance grade indicated.

b. Allowable Water Infiltration: No water penetration.

4. Testing Extent: Three sliding aluminum-framed glass doors of each type as selected by Architect and a qualified independent testing and inspecting agency. Conduct tests after perimeter sealants have cured.

5. Test Reports: Prepared according to AAMA 502.

B. Sliding aluminum-framed glass door will be considered defective if it does not pass tests and inspections.


A. Lubricate hardware and moving parts.


B. Adjust operating panels and screens to provide a tight fit at contact points and weather stripping for smooth operation, without binding, and a weathertight closure. Adjust hardware for proper alignment, smooth operation, and proper latching without unnecessary force or excessive clearance.

C. Clean exposed surfaces immediately after installing sliding aluminum-framed glass doors. Avoid damaging protective coatings and finishes. Remove nonpermanent labels, excess sealants, glazing materials, dirt, and other substances.


E. Protect sliding aluminum-framed glass door surfaces from contact with contaminating substances resulting from construction operations. If contaminating substances contact sliding aluminum-framed glass door surfaces, remove contaminants immediately according to manufacturer's written instructions.

F. Refinish or replace sliding aluminum-framed glass doors with damaged finishes.

G. Replace damaged components.


VINYL REPLACEMENT WINDOWS

PART 1 - GENERAL



1.2 SUMMARY

A. This Section includes operable vinyl-framed replacement windows.

1.3 DEFINITIONS

A. Performance class designations according to AAMA/WDMA 101/I.S.2/NAFS:

1. AW: Architectural. 2. HC: Heavy Commercial. 3. C: Commercial. 4. LC: Light Commercial. 5. R: Residential.

B. Performance grade number according to AAMA/WDMA 101/I.S.2/NAFS:

1. Design pressure number in pounds force per square foot used to determine the structural test pressure and water test pressure.

C. Structural Test Pressure: For uniform load structural test, is equivalent to 150 percent of the design pressure.

D. Minimum Test Size: Smallest size permitted for performance class (gateway test size). Products must be tested at minimum test size or at a size larger than minimum test size to comply with requirements for performance class.


A. General: Provide vinyl windows capable of complying with performance requirements indicated, based on testing manufacturer's windows that are representative of those specified, and that are of test size indicated below:

1. Size required by AAMA/WDMA 101/I.S.2/NAFS for gateway performance for both gateway performance and optional performance grade.

2. Size indicated on Drawings.

B. Windborne-Debris Resistance: Provide glazed windows capable of resisting impact from windborne debris, based on the pass/fail criteria as determined from testing glazed windows

identical to those specified, according to AAMA 506 and requirements of authorities having jurisdiction.

1.5 SUBMITTALS

A. Product Data: Include construction details, material descriptions, fabrication methods, dimensions of individual components and profiles, hardware, finishes, and operating instructions for each type of vinyl window indicated.

B. Shop Drawings: Include plans, elevations, sections, details, hardware, attachments to other work, operational clearances, installation details, and the following:

1. Mullion details, including reinforcement and stiffeners. 2. Joinery details. 3. Expansion provisions. 4. Flashing and drainage details. 5. Weather-stripping details. 6. Glazing details. 7. Window cleaning provisions.

C. Samples for Verification: For vinyl windows and components required, prepared on Samples of size indicated below.

1. One full size operable unit for owner review 1 ft. x 3 ft.

D. Product Schedule: For vinyl windows. Use same designations indicated on Drawings.

E. Qualification Data: For Installer and manufacturer.

F. Product Test Reports: Based on evaluation of comprehensive tests performed within the last four years by a qualified testing agency for each type, class, grade, and size of vinyl window. Test results based on use of downsized test units will not be accepted.

G. Maintenance Data: For operable window sash, operating hardware, weather stripping, and finishes to include in maintenance manuals.

H. Warranty: Special warranty specified in this Section.


A. Installer Qualifications: An installer acceptable to vinyl window manufacturer for installation of units required for this Project.

1. Installer's responsibilities include providing professional engineering services needed to assume engineering responsibility.

2. Engineering Responsibility: Preparation of data for vinyl windows, including Shop Drawings, based on testing and engineering analysis of manufacturer's standard units in assemblies similar to those indicated for this Project.

B. Manufacturer Qualifications: A manufacturer capable of fabricating vinyl windows that meet or exceed performance requirements indicated and of documenting this performance by inclusion in lists and by labels, test reports, and calculations.

C. Source Limitations: Obtain vinyl windows through one source from a single manufacturer.

D. Product Options: Information on Drawings and in Specifications establishes requirements for vinyl windows' aesthetic effects and performance characteristics. Aesthetic effects are indicated by dimensions, arrangements, alignment, and profiles of components and assemblies as they relate to sightlines, to one another, and to adjoining construction. Performance characteristics are indicated by criteria subject to verification by one or more methods including preconstruction testing, field testing, and in-service performance.

E. Product Options: Drawings indicate size, profiles, and dimensional requirements of vinyl windows and are based on the specific system indicated. Refer to Division 01 Section "Product Requirements." Do not modify size and dimensional requirements.

1. Do not modify intended aesthetic effects, as judged solely by Architect, except with Architect's approval. If modifications are proposed, submit comprehensive explanatory data to Architect for review.

F. Fenestration Standard: Comply with AAMA/WDMA 101/I.S.2/NAFS, "North American Fenestration Standard Voluntary Performance Specification for Windows, Skylights and Glass Doors," for definitions and minimum standards of performance, materials, components, accessories, and fabrication unless more stringent requirements are indicated.

1. Provide AAMA-certified vinyl windows with an attached label.

G. Glazing Publications: Comply with published recommendations of glass manufacturers and with GANA's "Glazing Manual" unless more stringent requirements are indicated.

H. Preinstallation Conference: Conduct conference at Project site. Review methods and procedures related to vinyl windows including, but not limited to, the following:

1. Review and finalize construction schedule and verify availability of materials, Installer's personnel, equipment, and facilities needed to make progress and avoid delays.

2. Review, discuss, and coordinate the interrelationship of vinyl windows with other exterior wall components. Include provisions for structural anchorage, glazing, flashing, weeping, sealants, and protection of finishes.

3. Review and discuss the sequence of work required to construct a watertight and weathertight exterior building envelope.

4. Inspect and discuss the condition of substrate and other preparatory work performed by other trades.


A. Field Measurements: Verify vinyl window openings by field measurements before fabrication and indicate measurements on Shop Drawings.

1. Established Dimensions: Where field measurements cannot be made without delaying the Work, establish opening dimensions and proceed with fabricating vinyl windows

without field measurements. Coordinate wall construction to ensure that actual opening dimensions correspond to established dimensions.

1.8 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace vinyl windows that fail in materials or workmanship within specified warranty period.


a. Failure to meet performance requirements. b. Structural failures including excessive deflection, water leakage, air infiltration, or

condensation. c. Faulty operation of movable sash and hardware. d. Deterioration of vinyl, other materials, and finishes beyond normal weathering. e. Failure of insulating glass.

2. Warranty Period:

a. Window: Ten years from date of Substantial Completion. b. Glazing: Five years from date of Substantial Completion. c. Vinyl Finish: Five years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

B. Basis-of-Design Product: Subject to compliance with requirements, provide the product indicated on Drawings, Polaris Technologies Ultra Weld Collection, or a comparable product by one of the following:

1. Alside, Inc. Akron, OH 800.922.6009 www.alside.com

2. CertainTeed Corp. Valley Forge, PA 800.233.8990 www.certainteed.com

3. Gentek Building Products, Inc. Akron, OH 800.475.5061 www.gentekinc.com

http://www.alside.com/

http://www.certainteed.com/

http://www.gentekinc.com/

2.2 MATERIALS

A. Vinyl Extrusions: Rigid (unplasticized) hollow PVC extrusions, formulated and extruded for exterior applications, complying with AAMA/WDMA 101/I.S.2/NAFS and the following:

1. PVC Resins: 100 percent virgin resin. 2. PVC Formulation: High impact, low heat buildup, lead free, nonchalking, and color and

UV stabilized. 3. Extrusion Wall Thickness: Not less than 0.090 inch. 4. Multichamber Extrusions: Profile designed with multichambers between interior and

exterior faces of the extrusions.

B. Vinyl Trim and Glazing Stops: Material and finish to match frame members.

C. Fasteners: Aluminum, nonmagnetic stainless steel, epoxy adhesive, or other materials warranted by manufacturer to be noncorrosive and compatible with vinyl window members, cladding, trim, hardware, anchors, and other components.

1. Exposed Fasteners: Unless unavoidable for applying hardware, do not use exposed fasteners. For application of hardware, use fasteners that match finish of member or hardware being fastened, as appropriate.

D. Anchors, Clips, and Accessories: Aluminum, nonmagnetic stainless steel, or zinc-coated steel or iron complying with ASTM B 633 for SC 3 severe service conditions; provide sufficient strength to withstand design pressure indicated.

E. Reinforcing Members: Aluminum, or nonmagnetic stainless steel, or nickel/chrome-plated steel complying with ASTM B 456 for Type SC 3 severe service conditions, or zinc-coated steel or iron complying with ASTM B 633 for SC 3 severe service conditions; provide sufficient strength to withstand design pressure indicated.

F. Compression-Type Weather Stripping: Provide compressible weather stripping designed for permanently resilient sealing under bumper or wiper action, and for complete concealment when vinyl window is closed.

1. Weather-Stripping Material: Elastomeric cellular preformed gaskets complying with ASTM C 509.

2. Weather-Stripping Material: Dense elastomeric gaskets complying with ASTM C 864. 3. Weather-Stripping Material: Manufacturer's standard system and materials complying

with AAMA/WDMA 101/I.S.2/NAFS.

G. Sliding-Type Weather Stripping: Provide woven-pile weather stripping of wool, polypropylene, or nylon pile and resin-impregnated backing fabric. Comply with AAMA 701/702.

1. Weather Seals: Provide weather stripping with integral barrier fin or fins of semirigid, polypropylene sheet or polypropylene-coated material. Comply with AAMA 701/702.

H. Replaceable Weather Seals: Comply with AAMA 701/702.

2.3 VINYL REPLACEMENT WINDOWS

A. Window Type: As indicated on Drawings.

B. AAMA/WDMA Performance Requirements: Provide vinyl windows of performance indicated that comply with AAMA/WDMA 101/I.S.2/NAFS.

1. Performance Class: C.

C. Condensation-Resistance Factor (CRF): Provide vinyl windows tested for thermal performance according to AAMA 1503, showing a CRF of 52.

D. Thermal Transmittance: Provide vinyl windows with a whole-window, U-factor maximum indicated at 15-mph exterior wind velocity and winter condition temperatures when tested according to NFRC 100.

1. U-Factor: 0.35 Btu/sq. ft. x h x deg F or less.

E. Solar Heat-Gain Coefficient (SHGC): Provide vinyl windows with a whole-window SHGC maximum of 0.50, determined according to NFRC 200 procedures.

F. Air Infiltration: Maximum rate not more than indicated when tested according to AAMA/WDMA 101/I.S.2/NAFS, Air Infiltration Test.

1. Maximum Rate: 0.3 cfm/sq. ft. of area at an inward test pressure of 1.57 lbf/sq. ft..

G. Water Resistance: No water leakage as defined in AAMA/WDMA referenced test methods at a water test pressure equaling that indicated, when tested according to AAMA/WDMA 101/I.S.2/NAFS, Water Resistance Test.

1. Test Pressure: 15 percent of positive design pressure, but not less than 2.86 lbf/sq. ft. or more than 15 lbf/sq. ft..

H. Forced-Entry Resistance: Comply with Performance Grade 30 requirements when tested according to ASTM F 588.

I. Life-Cycle Testing: Test according to AAMA 910 and comply with AAMA/WDMA 101/I.S.2/NAFS.

J. Operating Force and Auxiliary (Durability) Tests: Comply with AAMA/WDMA 101/I.S.2/NAFS for operating window types indicated.

2.4 GLAZING

A. Glass Clear, insulating-glass units, argon gas filled, with low-E coating pyrolytic on second surface or sputtered on second or third surface.

B. Glazing System: Manufacturer's standard factory-glazing system that produces weathertight seal.

2.5 HARDWARE

A. General: Provide manufacturer's standard hardware fabricated from aluminum, stainless steel, carbon steel complying with AAMA 907, or other corrosion-resistant material compatible with vinyl; designed to smoothly operate, tightly close, and securely lock vinyl windows, and sized to accommodate sash or ventilator weight and dimensions. Do not use aluminum in frictional

contact with other metals. Where exposed, provide extruded, cast, or wrought aluminum or die-cast zinc with special coating finish.

B. Counterbalancing Mechanism: Comply with AAMA 902.

1. Sash-Balance Type: Concealed, spring-loaded, block-and-tackle type, of size and capacity to hold sash stationary at any open position.

C. Sill Cap/Track: Extruded-aluminum track with natural anodized finish or rigid PVC or other weather-resistant plastic track with manufacturer's standard integral color, of thickness, dimensions, and profile indicated; designed to comply with performance requirements indicated and to drain to the exterior.

D. Locks and Latches: Designed to allow unobstructed movement of the sash across adjacent sash in direction indicated and operated from the inside only. Provide custodial locks.

E. Roller Assemblies: Low-friction design.

F. Push-Bar Operators: Provide telescoping-type, push-bar operator designed to open and close ventilators with fixed screens.

G. Gear-Type Rotary Operators: Comply with AAMA 901 when tested according to ASTM E 405, Method A.

1. Operation Function: All ventilators move simultaneously and securely close at both jambs without using additional manually controlled locking devices.

H. Four- or Six-Bar Friction Hinges: Comply with AAMA 904.

1. Locking mechanism and handles for manual operation. 2. Friction Shoes: Provide friction shoes of nylon or other nonabrasive, nonstaining,

noncorrosive, durable material.

I. Limit Devices: Provide concealed friction adjustor, adjustable stay bar limit devices designed to restrict sash or ventilator opening.

1. Safety Devices: Limit clear opening to 6 inches for ventilation; with custodial key release.

J. Pole Operators: Tubular-shaped anodized aluminum; with rubber-capped lower end and standard push-pull hook at top to match hardware design; of sufficient length to operate window without reaching more than 60 inches above floor; 1 pole operator and pole hanger per room that has operable windows more than 72 inches above floor.

2.6 INSECT SCREENS

A. General: Design windows and hardware to accommodate screens in a tight-fitting, removable arrangement, with a minimum of exposed fasteners and latches. Fabricate insect screens to fully integrate with window frame. Locate screens on outside of window and provide for each operable exterior sash or ventilator.

1. Aluminum Tubular Frame Screens: Comply with SMA 1004, "Specifications for Aluminum Tubular Frame Screens for Windows," Architectural C-24 class.

B. Aluminum Insect Screen Frames: Manufacturer's standard aluminum alloy complying with SMA 1004. Fabricate frames with mitered or coped joints or corner extrusions, concealed fasteners, adjustable rollers, and removable PVC spline/anchor concealing edge of frame.

1. Aluminum Tubular Framing Sections and Cross Braces: Roll formed from aluminum sheet with minimum wall thickness as required for class indicated.

2. Finish: Anodized aluminum in manufacturer's standard color. 3. Finish: Manufacturer's standard.

C. Glass-Fiber Mesh Fabric: 18-by-14 or 18-by-16 mesh of PVC-coated, glass-fiber threads; woven and fused to form a fabric mesh resistant to corrosion, shrinkage, stretch, impact damage, and weather deterioration, in the following color. Comply with ASTM D 3656.

1. Mesh Color: Silver gray.

D. Aluminum Wire Fabric: 18-by-16 mesh of 0.011-inch- diameter, coated aluminum wire.

1. Wire-Fabric Finish: Natural bright.

2.7 FABRICATION

A. Fabricate vinyl windows in sizes indicated. Include a complete system for assembling components and anchoring windows.

1. Welded Frame and Sash/Ventilator Corners: Miter-cut and fusion or chemically welded.

B. Fabricate vinyl windows that are reglazable without dismantling sash or ventilator framing.

C. Weather Stripping: Provide full-perimeter weather stripping for each operable sash and ventilator, unless otherwise indicated.

1. Double-Hung Windows: Provide weather stripping only at horizontal rails of operable sash.

D. Mullions: Provide mullions and cover plates as shown, compatible with window units, complete with anchors for support to structure and installation of window units. Allow for erection tolerances and provide for movement of window units due to thermal expansion and building deflections, as indicated. Provide mullions and cover plates capable of withstanding design loads of window units. Provide manufacturer's standard finish to match window units.

E. Subframes: Provide subframes with anchors for window units as shown, of profile and dimensions indicated but not less than 0.062-inch- thick extruded aluminum. Miter or cope corners, and weld and dress smooth with concealed mechanical joint fasteners. Provide manufacturer's standard finish to match window units. Provide subframes capable of withstanding design loads of window units.

F. Factory-Glazed Fabrication: Except for light sizes in excess of 100 united inches, glaze vinyl windows in the factory where practical and possible for applications indicated. Comply with requirements in Division 08 Section "Glazing" and with AAMA/WDMA 101/I.S.2/NAFS.

G. Hardware: Mount hardware through double walls of vinyl extrusions or provide corrosion-resistant steel reinforcement complying with requirements for reinforcing members, or do both.

H. Complete fabrication, assembly, finishing, hardware application, and other work in the factory to greatest extent possible. Disassemble components only as necessary for shipment and installation. Allow for scribing, trimming, and fitting at Project site.

2.8 VINYL FINISHES

A. Integral Finish and Color: Uniform, solid, homogeneous white interior and exterior.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine openings, substrates, structural support, anchorage, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of work. Verify rough opening dimensions, levelness of sill plate, and operational clearances. Examine wall flashings, vapor retarders, water and weather barriers, and other built-in components to ensure a coordinated, weathertight window installation.

1. Masonry Surfaces: Visibly dry and free of excess mortar, sand, and other construction debris.

2. Wood Frame Walls: Dry, clean, sound, well nailed, free of voids, and without offsets at joints. Ensure that nail heads are driven flush with surfaces in opening and within 3 inches of opening.

3. Metal Surfaces: Dry; clean; free of grease, oil, dirt, rust, corrosion, and welding slag; without sharp edges or offsets at joints.

4. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 INSTALLATION

A. Comply with Drawings, Shop Drawings, and manufacturer's written instructions for installing windows, hardware, accessories, and other components.

B. Install windows level, plumb, square, true to line, without distortion or impeding thermal movement, anchored securely in place to structural support, and in proper relation to wall flashing and other adjacent construction.

C. Set sill members in bed of sealant or with gaskets, as indicated, for weathertight construction.

D. Separate aluminum and other corrodible surfaces from sources of corrosion or electrolytic action at points of contact with other materials.


A. Adjust operating sashes and ventilators, screens, hardware, and accessories for a tight fit at contact points and weather stripping for smooth operation and weathertight closure. Lubricate hardware and moving parts.

B. Clean exposed surfaces immediately after installing windows. Avoid damaging protective coatings and finishes. Remove excess sealants, glazing materials, dirt, and other substances.

C. Clean factory-glazed glass immediately after installing windows. Comply with manufacturer's written recommendations for final cleaning and maintenance. Remove nonpermanent labels, and clean surfaces.


E. Protect window surfaces from contact with contaminating substances resulting from construction operations. In addition, monitor window surfaces adjacent to and below exterior concrete and masonry surfaces during construction for presence of dirt, scum, alkaline deposits, stains, or other contaminants. If contaminating substances do contact window surfaces, remove contaminants immediately according to manufacturer's written recommendations.

END OF SECTION 08 53 13

RESILIENT BASE AND ACCESSORIES 09 6513 - 1 SMHA Site Renovation 2017349.01 March 01, 2017

SECTION 09 6513 - RESILIENT BASE AND ACCESSORIES

PART 1 - GENERAL

1.1 SECTION REQUIREMENTS

A. Submittals: Product Data and Samples.

B. Extra Materials: Furnish not less than 10 linear feet (3 linear m) for every 500 linear feet (150 linear m) or fraction thereof, of each type, color, pattern, and size of resilient product installed.

PART 2 - PRODUCTS

2.1 WALL BASE

A. Products from one of the following manufacturers:

1. Johnsonite (Basis-of-Design) 2. American Biltrite 3. VPI

B. Color and Pattern: Johnsonite DC49 4x4 TOE 4” x 4’ strip or color to match. Color to be selected by Architect.

C. ASTM F 1861, Type TS (rubber, vulcanized thermoset) or TP (rubber, thermoplastic).

D. Group (Manufacturing Method): I (solid)

E. Style: Cove (with top-set toe).

F. Minimum Thickness: 0.125 inch (3.2 mm)

G. Lengths: coils in manufacturer's standard lengths.

H. Outside Corners: premolded.

I. Inside Corners: premolded.

2.2 INSTALLATION ACCESSORIES

A. Trowelable Leveling and Patching Compounds: Latex-modified, portland cement- or blended hydraulic cement-based formulation provided or approved by flooring manufacturer for applications indicated.

B. Adhesives: Water-resistant type recommended by manufacturer to suit products and substrate conditions.


2.3 RUBBER STAIR ACCESSORIES

A. Fire-Test-Response Characteristics: As determined by testing identical products according to ASTM E 648 or NFPA 253 by a qualified testing agency.

1. Critical Radiant Flux Classification: Class I, not less than 0.45 W/sq. cm.

B. Stair Treads: ASTM F 2169.

1. Type: TS (rubber, vulcanized thermoset) or TP (rubber, thermoplastic). 2. Class: 2 (pattern; embossed, grooved, or ribbed). 3. Group: 2 (with contrasting color for the visually impaired, photoluminescent). 4. Nosing Style: Square, adjustable to cover angles between 60 and 90 degrees. 5. Nosing Height: 2 inches (51 mm). 6. Thickness: 1/4 inch (6 mm) and tapered to back edge. 7. Size: Lengths and depths to fit each stair tread one piece or, for treads exceeding

maximum lengths manufactured, in equal-length units. 8. Integral Risers: Smooth, flat; in height that fully covers substrate.

C. Separate Risers: Smooth, flat; in height that fully covers substrate; produced by same manufacturer as treads and recommended by manufacturer for installation with treads.

1. Style: Toeless, by length matching treads. 2. Thickness: 0.125 inch (3.2 mm).

D. Landing Tile: Matching treads; produced by same manufacturer as treads and recommended by manufacturer for installation with treads.

E. Locations: Provide rubber stair accessories in areas indicated.

F. Colors and Patterns: Match resilient floor tile color.

2.4 RUBBER MOLDING ACCESSORY

A. Description: Rubber stair-tread nosing, carpet edge for glue-down applications, nosing for carpet, nosing for resilient flooring, reducer strip for resilient flooring, joiner for tile and carpet, transition strips.

B. Locations: Provide rubber molding accessories in areas indicated.

C. Colors and Patterns: As selected by Architect from full range of industry colors.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Prepare concrete substrates according to ASTM F 710. Verify that substrates are dry and free of curing compounds, sealers, and hardeners.


B. Adhesively install resilient wall base and accessories.

C. Install wall base in maximum lengths possible. Apply to walls, columns, pilasters, casework, and other permanent fixtures in rooms or areas where base is required.

D. Install reducer strips at edges of floor coverings that would otherwise be exposed.


RESILIENT TILE FLOORING 09 6519 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 09 6519 - RESILIENT TILE FLOORING

PART 1 - GENERAL


A. Drawings and general provisions of the Contract, including General and Supplemen-tary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY


1. Luxury vinyl plank flooring.

1.3 RELATED SECTIONS

A. Division 09 Section "Resilient Base" for resilient base, installed with resilient floor coverings.

1.4 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Shop Drawings: For each type of floor tile. Include floor tile layouts, edges, col-

umns, doorways, enclosing partitions, built-in furniture, cabinets, and cutouts.

C. Samples for Verification: Full-size units of each color and pattern of floor tile required.

D. Qualification Data: For qualified Installer.

E. Maintenance Data: For each type of floor tile to include in maintenance manuals. 1.5 QUALITY ASSURANCE

A. Installer Qualifications: A qualified installer who employs workers for this Project who are

competent in techniques required by manufacturer for floor tile installation indicated.

1. Engage an installer who employs workers for this Project who are trained or certified by manufacturer for installation techniques required.

B. Fire-Test-Response Characteristics: As determined by testing identical products according

to ASTM E 648 or NFPA 253 by a qualified testing agency.

1. Critical Radiant Flux Classification: Class I, not less than 0.45 W/sq. cm. 1.6 DELIVERY, STORAGE, AND HANDLING


A. Store floor tile and installation materials in dry spaces protected from the weather, with am-

bient temperatures maintained within range recommended by manufacturer, but not less than 50 deg F or more than 90 deg F. Store floor tiles on flat surfaces.


A. Maintain ambient temperatures within range recommended by manufacturer, but not less

than 70 deg F or more than 95 deg F, in spaces to receive floor tile during the following time periods:

1. 48 hours before installation.

2. During installation. 3. 48 hours after installation.

B. Until Substantial Completion, maintain ambient temperatures within range recommended

by manufacturer, but not less than 55 deg F or more than 95 deg F.

C. Close spaces to traffic during floor tile installation.

D. Close spaces to traffic for 48 hours after floor tile installation.

E. Install floor tile after other finishing operations, including painting, have been completed. 1.8 WARRANTY

A. Manufacturer’s standard ten (10) year warranty.

B. PART 2 - PRODUCTS

2.1 LUXURY VINYL TILE (LVT)

A. Product: Subject to compliance with requirements, provide Tandus Centiva, a Tarkett company.

B. Tile Standard: ASTM F 1700, Class III, Type B, Embossed surface.

C. Colors and Patterns: “Venue Wood” as selected by Owner.

D. Total thickness 20mil.

E. Size: 6 by 48-inch. 2.2 INSTALLATION MATERIALS

A. Trowelable Leveling and Patching Compounds: Latex-modified, portland cement based

or blended hydraulic-cement-based formulation provided or approved by manufacturer for applications indicated.


B. Adhesives: Water-resistant type recommended by manufacturer to suit floor tile and sub-

strate conditions indicated.

1. Comply with applicable regulations regarding toxic and hazardous materials Green Seal (GS-36) for commercial adhesive.

2. Use low-VOC adhesive during installation. Water based is preferred over solvent based adhesives.

C. Floor Polish/Wax: Provide protective liquid floor polish products as recommended

by manufacturer.

PART 3 - EXECUTION 3.1 EXAMINATION

A. Examine substrates, with Installer present, for compliance with requirements for maxi-

mum moisture content and other conditions affecting performance of the Work.

B. Verify that finishes of substrates comply with tolerances and other requirements specified in other Sections and that substrates are free of cracks, ridges, depressions, scale, and foreign deposits that might interfere with adhesion of floor tile.


D. Comply with manufacturer's written instructions for preparing substrate.

3.2 PREPARATION

A. Prepare substrates according to manufacturer's written instructions to ensure adhe-

sion of resilient products.

B. Fill cracks, holes, and depressions in substrates with trowelable leveling and patch-ing compound and remove bumps and ridges to produce a uniform and smooth substrate.

C. Do not install floor tiles until they are same temperature as space where they are to be in-

stalled.

1. Move resilient products and installation materials into spaces where they will be in-stalled at least 48 hours in advance of installation.

D. Sweep and vacuum clean substrates to be covered by resilient products immediately be-

fore installation. 3.3 FLOOR TILE INSTALLATION

A. Comply with manufacturer's written instructions for installing floor tile.

B. Lay out floor tiles from center marks established with principal walls, discounting minor off-


sets, so tiles at opposite edges of room are of equal width. Adjust as necessary to avoid using cut widths that equal less than one-half tile at perimeter.

1. Pattern: Unidirectional.

C. Match floor tiles for color and pattern by selecting tiles from cartons in the same sequence

as manufactured and packaged, if so numbered. Discard broken, cracked, chipped, or de-formed tiles.

D. Scribe, cut, and fit floor tiles to butt neatly and tightly to vertical surfaces and perma-

nent fixtures including built-in furniture, cabinets, pipes, outlets, and door frames.

E. Extend floor tiles into toe spaces, door reveals, closets, and similar openings. Extend floor tiles to center of door openings.

F. Maintain reference markers, holes, and openings that are in place or marked for future cut-ting by repeating on floor tiles as marked on substrates. Use chalk or other nonpermanent, nonstaining marking device.

G. Adhere floor tiles to flooring substrates using a full spread of adhesive applied to substrate

to produce a completed installation without open cracks, voids, raising and puckering at joints, telegraphing of adhesive spreader marks, and other surface imperfections.


A. Comply with manufacturer's written instructions for cleaning and protection of floor tile.

B. Perform the following operations immediately after completing floor tile installation:

1. Remove adhesive and other blemishes from exposed surfaces. 2. Sweep and vacuum surfaces thoroughly. 3. Damp-mop surfaces to remove marks and soil.

C. Protect floor tile products from mars, marks, indentations, and other damage from construc-

tion operations and placement of equipment and fixtures during remainder of construction period.

D. Floor Polish/Wax/Sealer: Remove soil, visible adhesive and surface blemishes from floor tile

surfaces and apply manufacturer’s recommended floor finish material. Apply at rate rec-ommended by manufacturer.

E. Cover floor tile until Substantial Completion.

EXTERIOR PAINTING 09 9113 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 09 9113 – EXTERIOR PAINTING

PART 1 - GENERAL

1.1 SECTION REQUIREMENTS

A. Summary: Paint exposed surfaces, new and existing, per unit matrices.

B. Submittals:

1. Product Data. Include printout of "MPI Approved Products List" with product highlighted. 2. Samples.

C. MPI Standards:

1. Products: Complying with MPI standards indicated and listed in "MPI Approved Products List."

2. Preparation and Workmanship: Comply with requirements in "MPI Architectural Painting Specification Manual" for products and paint systems indicated.

D. Extra Materials: Deliver to Owner 1 gal. of each color and type of finish coat paint used on Project, in containers, properly labeled and sealed.

PART 2 - PRODUCTS

2.1 PAINT

A. Available Products:

1. Benjamin Moore & Co. 2. ICI Devoe Coatings. 3. Sherwin-Williams Company (The) 4. PPG Architectural Finishes, Inc.

B. Material Compatibility: Provide materials that are compatible with one another and with substrates.

1. For each coat in a paint system, provide products recommended in writing by manufacturers of topcoat for use in paint system and on substrate indicated.

C. Colors: As selected.


PART 3 - EXECUTION

3.1 PREPARATION

A. Remove hardware, lighting fixtures, and similar items that are not to be painted. Mask items that cannot be removed. Reinstall items in each area after painting is complete.

B. Clean and prepare surfaces in an area before beginning painting in that area. Schedule painting so cleaning operations will not damage newly painted surfaces.

3.2 APPLICATION

A. Apply paints according to manufacturer's written instructions.

1. Use brushes only for exterior painting and where the use of other applicators is not practical.

2. Use rollers for finish coat on interior walls and ceilings.

B. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks.

1. If undercoats or other conditions show through topcoat, apply additional coats until cured film has a uniform paint finish, color, and appearance.

C. Apply stains and transparent finishes to produce surface films without color irregularity, cloudiness, holidays, lap marks, brush marks, runs, ropiness, or other imperfections. Use multiple coats to produce a smooth surface film of even luster.

3.3 EXTERIOR PAINT APPLICATION SCHEDULE

A. Steel:

1. High-build Epoxy Marine Coating, low gloss MPI #108.

B. Galvanized Metal:

1. Semigloss, Alkyd Enamel: Two coats over cementitious galvanized-metal primer: MPI EXT 5.3B.

C. Dressed Lumber: Including architectural woodwork.

1. Solid-Color Latex Stain: Two coats over latex primer: MPI EXT 6.3K. 2. Semitransparent Stain: Two coats: MPI EXT 6.3D.

D. Wood Panel Products: Including fascias and soffits.

1. Solid-Color Latex Stain: Two coats over latex primer: MPI EXT 6.4A. 2. Semitransparent Stain: Two coats: MPI EXT 6.4D.

INTERIOR PAINTING 09 9123 - 1 2017349.01

INTERIOR PAINTING

PART 1 - GENERAL



1.2 SUMMARY

A. This Section includes surface preparation and the application of paint systems on the following interior substrates: 1. Gypsum board.

1.3 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Samples for Verification: For each type of paint system and in each color and gloss of topcoat indicated.

1. Submit Samples on rigid backing, 8 inches square. 2. Step coats on Samples to show each coat required for system. 3. Label each coat of each Sample. 4. Label each Sample for location and application area.

C. Product List: For each product indicated, include the following:

1. Cross-reference to paint system and locations of application areas. Use same designations indicated on Drawings and in schedules. Label MP1 systems.

2. Printout of current "MPI Approved Products List" for each product category specified in Part 2, with the proposed product highlighted.


A. MPI Standards:

1. Products: Complying with MPI standards indicated and listed in "MPI Approved Products List."

2. Preparation and Workmanship: Comply with requirements in "MPI Architectural Painting Specification Manual" for products and paint systems indicated.



A. Store materials not in use in tightly covered containers in well-ventilated areas with ambient temperatures continuously maintained at not less than 45 deg F.

1. Maintain containers in clean condition, free of foreign materials and residue. 2. Remove rags and waste from storage areas daily.


A. Apply paints only when temperature of surfaces to be painted and ambient air temperatures are between 50 and 95 deg F.

B. Do not apply paints when relative humidity exceeds 85 percent; at temperatures less than 5 deg F above the dew point; or to damp or wet surfaces.

1.7 EXTRA MATERIALS

A. Furnish extra materials described below that are from same production run (batch mix) as materials applied and that are packaged for storage and identified with labels describing contents.

1. Quantity: Furnish an additional 5 percent, but not less than 1 gal. of each material and color applied.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. Sherwin-Williams Company (The). (Basis-of-Design)

B. Colors: 1. White

2.2 PAINT, GENERAL

A. Material Compatibility:

1. Provide materials for use within each paint system that are compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience.

2. For each coat in a paint system, provide products recommended in writing by manufacturers of topcoat for use in paint system and on substrate indicated.

B. VOC Content of Field-Applied Interior Paints and Coatings: Provide products that comply with the following limits for VOC content, exclusive of colorants added to a tint base, when


calculated according to 40 CFR 59, Subpart D (EPA Method 24); these requirements do not apply to paints and coatings that are applied in a fabrication or finishing shop:

1. Flat Paints, Coatings, and Primers: VOC content of not more than 50 g/L. 2. Nonflat Paints, Coatings, and Primers: VOC content of not more than 150 g/L. 3. Anti-Corrosive and Anti-Rust Paints Applied to Ferrous Metals: VOC not more than 250

g/L. 4. Flat Topcoat Paints: VOC content of not more than 50 g/L. 5. Nonflat Topcoat Paints: VOC content of not more than 150 g/L. 6. Anti-Corrosive and Anti-Rust Paints Applied to Ferrous Metals: VOC not more than 250

g/L. 7. Zinc-Rich Industrial Maintenance Primers: VOC content of not more than 340 g/L. 8. Pre-Treatment Wash Primers: VOC content of not more than 420 g/L.

C. Chemical Components of Field-Applied Interior Paints and Coatings: Provide topcoat paints and anti-corrosive and anti-rust paints applied to ferrous metals that comply with the following chemical restrictions; these requirements do not apply to paints and coatings that are applied in a fabrication or finishing shop:

1. Aromatic Compounds: Paints and coatings shall not contain more than 1.0 percent by weight of total aromatic compounds (hydrocarbon compounds containing one or more benzene rings).

2. Restricted Components: Paints and coatings shall not contain any of the following:

a. Acrolein. b. Acrylonitrile. c. Antimony. d. Benzene. e. Butyl benzyl phthalate. f. Cadmium. g. Di (2-ethylhexyl) phthalate. h. Di-n-butyl phthalate. i. Di-n-octyl phthalate. j. 1,2-dichlorobenzene. k. Diethyl phthalate. l. Dimethyl phthalate. m. Ethylbenzene. n. Formaldehyde. o. Hexavalent chromium. p. Isophorone. q. Lead. r. Mercury. s. Methyl ethyl ketone. t. Methyl isobutyl ketone. u. Methylene chloride. v. Naphthalene. w. Toluene (methylbenzene). x. 1,1,1-trichloroethane. y. Vinyl chloride.


2.3 PRIMERS/SEALERS

A. Interior Latex Primer/Sealer: MPI #50.

1. VOC Content: E Range of E2. 2. Environmental Performance Rating: EPR 2.

2.4 METAL PRIMERS

A. Alkyd Anticorrosive Metal Primer: MPI #79.

1. VOC Content: E Range of E1.

2.5 LATEX PAINTS

A. Interior Latex (Semigloss): MPI #54 (Gloss Level 5).


2.6 ALKYD PAINTS

A. Interior Alkyd (Semigloss): MPI #47 (Gloss Level 5).


PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates and conditions, with Applicator present, for compliance with requirements for maximum moisture content and other conditions affecting performance of work.

B. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows:

1. Gypsum Board: 12 percent.

C. Verify suitability of substrates, including surface conditions and compatibility with existing finishes and primers.

D. Begin coating application only after unsatisfactory conditions have been corrected and surfaces are dry.

1. Beginning coating application constitutes Contractor's acceptance of substrates and conditions.


3.2 PREPARATION

A. Comply with manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual" applicable to substrates indicated.

B. Remove plates, machined surfaces, and similar items already in place that are not to be painted. If removal is impractical or impossible because of size or weight of item, provide surface-applied protection before surface preparation and painting.

1. After completing painting operations, use workers skilled in the trades involved to reinstall items that were removed. Remove surface-applied protection if any.

2. Do not paint over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates.

C. Clean substrates of substances that could impair bond of paints, including dirt, oil, grease, and incompatible paints and encapsulants.

1. Remove incompatible primers and reprime substrate with compatible primers as required to produce paint systems indicated.

D. Concrete Masonry Substrates: Remove efflorescence and chalk. Do not paint surfaces if moisture content or alkalinity of surfaces to be painted exceeds that permitted in manufacturer's written instructions.

E. Steel Substrates: Remove rust and loose mill scale. Clean using methods recommended in writing by paint manufacturer.

F. Gypsum Board Substrates: Do not begin paint application until finishing compound is dry and sanded smooth.

3.3 APPLICATION

A. Apply paints according to manufacturer's written instructions.

1. Use applicators and techniques suited for paint and substrate indicated. 2. Paint surfaces behind movable equipment and furniture same as similar exposed

surfaces. Before final installation, paint surfaces behind permanently fixed equipment or furniture with prime coat only.

3. Paint front and backsides of access panels, removable or hinged covers, and similar hinged items to match exposed surfaces.

B. Tint each undercoat a lighter shade to facilitate identification of each coat if multiple coats of same material are to be applied. Tint undercoats to match color of topcoat, but provide sufficient difference in shade of undercoats to distinguish each separate coat.

C. If undercoats or other conditions show through topcoat, apply additional coats until cured film has a uniform paint finish, color, and appearance.

D. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks.


E. Painting Mechanical and Electrical Work: Paint items exposed in equipment rooms and occupied spaces including, but not limited to, the following:

1. Mechanical Work:

a. Uninsulated metal piping. b. Uninsulated plastic piping. c. Pipe hangers and supports. d. Tanks that do not have factory-applied final finishes. e. Visible portions of internal surfaces of metal ducts, without liner, behind air inlets

and outlets. f. Duct, equipment, and pipe insulation having cotton or canvas insulation covering

or other paintable jacket material. g. Mechanical equipment that is indicated to have a factory-primed finish for field

painting.

2. Electrical Work:

a. Switchgear. b. Panelboards. c. Electrical equipment that is indicated to have a factory-primed finish for field

painting.


A. Testing of Paint Materials: Owner reserves the right to invoke the following procedure at any time and as often as Owner deems necessary during the period when paints are being applied:

1. Owner will engage the services of a qualified testing agency to sample paint materials being used. Samples of material delivered to Project site will be taken, identified, sealed, and certified in presence of Contractor.

2. Testing agency will perform tests for compliance with product requirements. 3. Owner may direct Contractor to stop applying paints if test results show materials being

used do not comply with product requirements. Contractor shall remove noncomplying-paint materials from Project site, pay for testing, and repaint surfaces painted with rejected materials. Contractor will be required to remove rejected materials from previously painted surfaces if, on repainting with complying materials, the two paints are incompatible.


A. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from Project site.

B. After completing paint application, clean spattered surfaces. Remove spattered paints by washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces.

C. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and leave in an undamaged condition.


D. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces.

3.6 INTERIOR PAINTING SCHEDULE

A. CMU Substrates:

1. Latex System: MPI INT 4.2A.

a. Prime Coat: Interior/exterior latex block filler. b. Intermediate Coat: Interior latex matching topcoat. c. Topcoat: Interior latex (semigloss).

B. Steel Substrates:

1. Alkyd System: MPI INT 5.1E.

a. Prime Coat: Alkyd anticorrosive metal primer. b. Intermediate Coat: Interior alkyd matching topcoat. c. Topcoat: Interior alkyd (semigloss).

C. Gypsum Board Substrates:

1. Latex System: MPI INT 9.2A.

a. Prime Coat: Interior latex primer/sealer. b. Intermediate Coat: Interior latex matching topcoat. c. Topcoat: Interior latex (semigloss).

2.


RESIDENTIAL APPLIANCES 11 3100 - 1 SMHA Scattered Site Renovation 2017349.01.18

March 01, 2017

SECTION 11 3100 - RESIDENTIAL APPLIANCES

PART 1 - GENERAL



1.2 SUMMARY


1. Cooking appliances. 2. Refrigeration appliances. 3. Range hood.


A. Product Data: For each type of product indicated. Include rated capacit ies, oper-

ating characteristics, dimensions, furnished accessories, and finishes for each appliance.

B. Product Schedule: For appliances. Use same designations indicated on Drawings. 1.4 INFORMATIONAL SUBMITTALS

A. Warranties: Sample of special warranties.


A. Operation and Maintenance Data: For each residential appliance to include in operation and

maintenance manuals. 1.6 QUALITY ASSURANCE

A. Source Limitations: Obtain residential appliances from single source and each type

of residential appliance from single manufacturer.

B. Regulatory Requirements: Comply with the following:

1. NFPA: Provide electrical appliances listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

2. ANSI: Provide gas-burning appliances that comply with ANSI Z21 Series standards.


March 01, 2017

C. Accessibility: Where residential appliances are indicated to comply with accessibility require-ments, comply with [the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines and ICC/ANSI A117.1.

D. Preinstallation Conference: Conduct conference at Project site.

1.7 WARRANTY

A. Special Warranties: Manufacturer's standard form in which manufacturer agrees to repair or

replace residential appliances or components that fail in materials or workmanship within speci-fied warranty period.

1. Warranty Period: One year from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 RANGES

A. Basis-of-Design Product: Subject to compliance with requirements, provide Tappen TGF316GS. or comparable product by one of the following:

1. General Electric Company (GE). 2. Maytag; a division of Whirlpool Corporation. 3. Samsung.

B. Gas Range: Freestanding.

1. Width: 29 7/8 inches (762 mm). 2. Height: 47 1/2 inches (1190 mm). 3. Depth: 28 1/ 2 inches (724 mm). 4. Gas Burners: Four.

a. Power Ratings: Manufacturer's standard. b. Controls: Located on front. c. Ignition System: Electronic. d. Grates: Individual black heavy duty. e. Other Feature(s): Sealed burners.

5. Oven Features:

a. Capacity: 4.2 cu. ft. (1.189 cu. m). b. Operation: Baking and manual clean. c. Broiler: Located in separate roll-out drawer on bottom. d. Oven Door(s): Observation window. e. Gas Power Ratings:

1) Oven: Manufacturer's standard. 2) Broiler: Manufacturer's standard.

6. Electric Power Supply: 120 V, 60 Hz, 15 A. 7. Material: Porcelain-enameled cook top.

http://www.specagent.com/LookUp/?ulid=344&mf=04&mf=95&src=wd&mf=04&src=wd


March 01, 2017

a. Color/Finish: White 2.2 REFRIGERATOR/FREEZERS

A. Basis-of-Design P r oduc t : Subject t o comp l i a nce w i th r e qu i r eme n t s , p r ov i de

F r i g i d a i r e ; FRT1717B Series or comparable product by one of the following:

1. General Electric Company (GE). 2. Maytag; a division of Whirlpool Corporation. 3. Samsung.

B. Refrigerator/Freezer: Energy Star Labeled - Two-door refrigerator/freezer with freezer on top

and complying with AHAM HRF-1.

1. Type: Free standing. 2. Dimensions:

a. Width: 28 inches (711 mm). b. Depth: 30 1/8 inches (765 mm). c. Height: 64-3/8 inches (1635 mm).

3. Storage Capacity:

a. Refrigeration Compartment Volume: 12.6 cu. ft. (0.35 cu. m). b. Freezer Volume: 3.7 cu. ft. (0.104 cu. m). c. Shelf Area: 4.4 sq. ft. (0.408 sq. m)

4. Refrigerator Features:

a. Interior light in refrigeration compartment. b. Compartment Storage: Two adjustable humidity drawers, one clear snack drawer. c. Door Storage: Two with Gallon storage. d. Control Type: Upfront Temperature-controls.

5. Freezer Features: One ice tray.

a. Defrost Type: Automatic. b. Freezer cabinet shelves- 1 half-width wire. c. Freezer door shelves- Two full width.

6. Appliance Color/Finish: White. 7. Electric Power Supply: 120 V, 60 Hz, 15 A.

2.3 RANGE HOOD

A. Basis-of-Design Product: Subject to compliance with requirements, provide Broan Economy

Ventless or comparable product by one of the following:

1. Modern Aire Mfg. Corp. 2. Whirlpool.




March 01, 2017

B. Range Hood: Two-Speed Non-Ducted with a Non-Ducted Filter.

1. Type: Undercabinet. 2. Width: 30 inches (762 mm). 3. Height: 6 inches (152 mm). 4. Depth: 17 1/ 2 inches (444 mm). 5. Color: White. 6. Power: 120V, 2.0 Amps, 2850 RPM. 7. Features: Two speed fan switch with separate light switch. 8. Wall Control: Broan model 66W (White). UFAS units only.

a. Three-function independent control with plastic wall plate. b. Function: High / Low / Light.

9. Accessories: a. Broan-Nutone Backsplash in Reversible White/Almond

1) Material: Aluminum. 2) Panel Height from Range to Underside of Range Hood: 48-inches;

Contractor to verify height in field. 3) Product Width: 30 inches (762 mm). 4) Thickness 0.019 - 0.023 inches. (0.4826 mm – 0.5842 mm).


A. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, tem-

porary protective covering before shipping.

B. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates and conditions, with Installer present, for compliance with requirements for

installation tolerances, power connections, and other conditions affecting installation and per-formance of residential appliances.

B. Examine roughing-in for piping systems to verify actual locations of piping connections before

appliance installation.

C. Examine walls, ceilings, and roofs for suitable conditions where [overhead exhaust hoods] will be installed.

D. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of

the Work.

E. Proceed with installation only after unsatisfactory conditions have been corrected.

RESIDENTIAL APPLIANCES 11 3100 - 5 SMHA Scattered Site Renovation 2017349.01.18 March 01, 2017


A. General: Comply with manufacturer's written instructions.

B. Built-in Equipment: Securely anchor units to supporting cabinets or countertops with con-cealed fasteners. Verify that clearances are adequate for proper functioning and that rough openings are completely concealed.

C. Freestanding Equipment: Place units in final locations after finishes have been completed

in each area. Verify that clearances are adequate to properly operate equipment.

D. Range Anti-Tip Device: Install at each range according to manufacturer's written instructions.

E. Utilities: Comply with plumbing and electrical requirements.


A. Perform tests and inspections.

1. Manufacturer’s Field Service: Engage a factory-authorized service representative to inspect components, assemblies, and equipment installations, including connections, and to assist in testing.

B. Tests and Inspections:

1. Perform visual, mechanical, and electrical inspection and testing for each appliance

according to manufacturers' written recommendations. Certify compliance with each manufacturer's appliance-performance parameters.

2. Leak Test: After installation, test for leaks. Repair leaks and retest until no leaks exist. 3. Operational Test: After installation, start units to confirm proper operation. 4. Test and adjust controls and safeties. Replace damaged and malfunctioning controls

and components.

C. An appliance will be considered defective if it does not pass tests and inspections.

D. Prepare test and inspection reports.

3.4 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance person-nel to adjust, operate, and maintain residential appliances.


RESIDENTIAL PLUMBING FIXTURES 22 4100 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 22 4100 - RESIDENTIAL PLUMBING FIXTURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Condi-tions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY A. Section Includes:

1. Bathtubs. 2. Surrounds. 3. Faucets. 4. Lavatories. 5. Kitchen sinks. 6. Laundry trays. 7. Laminar-flow, faucet-spout outlets. 8. Water closets. 9. Toilet seats. 10. Supply fittings. 11. Waste fittings.


A. Product Data: For each type of product. 1. Include construction details, material descriptions, dimensions of individual components

and profiles, and finishes for lavatories. 2. Include rated capacities, operating characteristics, electrical characteristics, and furnished

specialties and accessories. B. Shop Drawings: Include diagrams for power, signal, and control wiring.


A. Coordination Drawings: Counter cutout templates for mounting of counter-mounted plumbing fixtures.

B. Sample Warranty: For special warranty.

1.5 CLOSEOUT SUBMITTALS A. Operation and Maintenance Data: For plumbing fixtures and faucets to include in emergency,

operation, and operation and maintenance manuals.

1.6 MAINTENANCE MATERIAL SUBMITTALS A. Furnish extra materials that match products installed and that are packaged with protective

covering for storage and identified with labels describing contents. 1. Faucet Washers and O-Rings: Equal to 10 percent of amount of each type and size in-

stalled. 2. Faucet Cartridges and O-Rings: Equal to 5 percent of amount of each type and size in-

stalled. 3. Toilet Seats: Equal to 5 percent of amount of each type installed.

PART 2 - PRODUCTS 2.1 BATHTUBS


A. Bathtubs FRP or PMMA. 1. Manufacturers FRP or PMMA Bathtubs:

a. Sterling b. Swan Corporation c. American Standard d. Aqua Bath

2. Fixture: a. Standard: ANSI Z124.1.2 for FRP or PMMA plastic bathtubs. b. Bathing Surface: Slip resistant according to ASTM F 462. c. Size: 60 by 30 inches with front apron. d. Color: White. e. Drain Location: Verify Left or Right end. f. Drain: NPS 1-1/2; chrome-plated brass, pop-up waste and overflow.

3. Faucet: See “Bathtub Faucets” 4. Supply Fittings: Included in faucet. 5. Tub Filler: Chrome-plated-brass diverter spout. 6. Waste Fittings:

a. Standard: ASME A112.18.2/CSA B45.125.2. b. Drain: Stainless steel or chrome-plated brass, removable strainer. c. Overflow: Chrome-plated-brass escutcheon with toggle drain-plug device. d. Drain Piping: Schedule 40 PVC, NPS 1-1/2 P-trap, and waste.

2.2 SURROUNDS

A. Surround FRP or PMMA.

1. Manufacturers FRP or PMMA surround: a. Sterling b. Swan Corporation c. American Standard d. Aqua Bath

2. Fixture: a. Standard: ANSI Z124.1.2 for FRP or PMMA plastic bathtubs. b. Three-piece c. Size: 60 by 30 by 58 inches. d. Color: White.

3. Faucet: See “Bathtub Faucets”

2.3 BATHTUB FAUCETS

A. NSF Standard: Comply with NSF/ANSI 61 Annex G, "Drinking Water System Components - Health Effects," for faucet materials that will be in contact with potable water.

B. Bathtub Faucets: Single handle, pressure balance. 1. Pressure-Balance Faucets:

a. Moen b. Kohler c. American Standard

2. Standards: ASME A112.18.1/CSA B125.1 and ASSE 1016. 3. Faucet:

a. Body Material: Solid brass. b. Finish: Polished chrome plate. c. Maximum Flow Rate: 1.75 gpm unless otherwise indicated.



d. Mounting: Exposed. e. Operation: Single handle, twist or rotate control, with hot- and cold-water indica-

tors. f. Antiscald Device: Integral with mixing valve. g. Check Stops: Check-valve type, integral with or attached to body; on hot- and

cold-water supply connections. h. Diverter: In-tub filler spout. i. Supply Connections: NPS 1/2.

4. Shower Head: a. Standard: ASME A112.18.1/CSA B125.1. b. Type: Ball joint with arm and flange. c. Shower Head Material: Metallic with chrome-plated finish. d. Spray Pattern: Fixed. e. Integral Volume Control: Required. f. Shower-Arm, Flow-Control Fitting: 1.75 gpm.

5. Bathtub Filler Spout: Chrome-plated brass.

2.4 LAVATORIES

A. Lavatories: vitreous china, wall mounted. 1. Manufacturers Vitreous-China Lavatories:

a. Gerber Maxell b. American Standard c. Kohler

2. Fixture: a. Standard: ASME A112.19.2/CSA B45.1 for vitreous-china lavatories. b. Type: Concealed Front. c. Rectangular Nominal Size: 22 by 18 inches d. Faucet-Hole Punching: 3 holes, 4-inch (102-mm) centers. e. Faucet-Hole Location: Rim. f. Color: White.

3. Supply Fittings: Comply with requirements in "Supply Fittings" Article. 4. Waste Fittings: Comply with requirements in "Waste Fittings" Article.

B. Lavatories: Oval, cultured marble integral bowl countertop.

1. Manufacturers Cultured-Marble Countertop Lavatories: a. DuPont, Corian b. Avonite c. Formica d. WilsonArt, Gilbraltar

2. Fixture: a. General: Countertop lavatory with integral bowl for mounting on base unit. b. Backsplash: Integral with countertop c. Overall Top Size: See Architectural Drawings for size. Provide with one bowl. d. Bowl Size: Oval. e. Faucet-Hole Punching: Three holes, 4-inch. f. Faucet-Hole Location: Countertop. g. Color: White.

2.5 LAVATORY FAUCETS



B. Lavatory Faucets: Two-handle mixing valve. 1. General-Duty, Copper- or Brass-Underbody Faucets:

a. Moen b. American Standard c. Kohler

2. Standard: ASME A112.18.1/CSA B125.1. 3. General: Include hot- and cold-water indicators; coordinate faucet inlets with supplies

and fixture holes; coordinate outlet with spout and fixture receptor. 4. Body Material: General-duty, copper or brass underbody with brass cover plate. 5. Finish: Polished chrome plate. 6. Maximum Flow Rate: 1.2 gpm 7. Centers: 4 inches. 8. Mounting: Deck, exposed. 9. Valve Handle(s): Knob, nonmetallic. 10. Inlet(s): NPS 1/2 male shank. 11. Spout: Rigid. 12. Spout Outlet: Aerator. 13. Operation: Compression, manual. 14. Drain: Pop up.

2.6 KITCHEN SINKS

A. Kitchen Sinks: Two bowl, counter mounted, stainless steel.

1. Stainless-Steel Kitchen Sinks: a. Aspen b. Elkay c. Kohler

2. Fixture: a. Standard: ASME A112.19.3/CSA B45.4 for stainless-steel kitchen sinks. b. Overall Dimensions: 33”x22”. c. Metal Thickness: 20 gauge. d. Left Bowl:

1) Dimensions: 14”x15.5”. 2) Drain: 3-1/2-inch (89-mm) crumb cup.

a) Location: Centered in bowl. e. Right Bowl:

1) Dimensions: 14”x15.5”. 2) Drain: 3-1/2-inch (89-mm) crumb cup.

a) Location: Centered in bowl. 3. Faucet: Kitchen Sink 4. Supply Fittings: Comply with requirements in "Supply Fittings" Article. 5. Waste Fittings: Comply with requirements in "Waste Fittings" Article, except include con-

tinuous waste for multibowl sinks.

2.7 LAUNDRY TRAYS

A. Laundry Trays: Plastic laundry tray. 1. Manufacturers

a. Swan Corporation



b. Crane Plumbing c. EL Mustee & Sons

2. Fixture: a. Standard: IAPMO/ANSI Z124.6. b. Style: Flat-rim ledge. c. Material: Plastic. d. Nominal Size: 23”x21”. e. Color: White. f. Mounting: Freestanding on manufacturer's standard legs or separate, painted-steel

stand. 3. Faucet: Laundry Tray. 4. Supply Fittings: Comply with requirements in "Supply Fittings" Article. 5. Waste Fittings: Comply with requirements in "Waste Fittings" Article.

2.8 SINK FAUCETS

A. NSF Standard: Comply with NSF/ANSI 61 Annex G, "Drinking Water System Components -

Health Effects," for faucet materials that will be in contact with potable water.

B. Sink Faucets: Solid brass, kitchen sink. 1. General-Duty, Solid-Brass Faucets:

a. Moen b. America Standard c. Kohler


and fixture holes; coordinate outlet with spout and fixture receptor. 4. Kitchen Sink Option: Separate hand spray complying with ASSE 1025. 5. Finish: Polished chrome plate. 6. Maximum Flow Rate: 1.5 gpm. 7. Mixing Valve: Single control. 8. Centers: 4 inches. 9. Mounting: Deck, exposed. 10. Handle: Lever. 11. Spout Type: Swing, round tubular. 12. Spout Outlet: Aerator.

C. Sink Faucets: Solid brass, laundry tray.

1. General-Duty, Solid-Brass Faucets: a. Moen b. America Standard c. Kohler


and fixture holes; coordinate outlet with spout and fixture receptor. 4. Kitchen Sink Option: Separate hand spray complying with ASSE 1025. 5. Finish: Polished chrome plate. 6. Mixing Valve: Single control. 7. Centers: 2 inches. 8. Mounting: Deck, exposed. 9. Handle: Two Knob. 10. Spout Type: Swing, round tubular.




11. Spout Outlet: Aerator. 2.9 WATER CLOSETS

A. Water Closets: Floor mounted, floor outlet, close coupled (gravity tank), vitreous china.

1. Manufacturers a. Gerber Maxell b. American Standard c. Kohler

2. Bowl:

a. Standards: ASME A112.19.2/CSA B45.1, ASME A112.19.5, and ASSE 1037. b. Bowl Type: Siphon jet. c. Height: Standard. d. Rim Contour: Regular. e. Water Consumption: Water saving, 1.28 gal/flush. f. Color: White.

3. Toilet Seat. 4. Supply Fittings:

a. Standard: ASME A112.18.1/CSA B125.1. b. Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching

water-supply piping size. Include chrome-plated wall flange. c. Stop: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with

inlet connection matching water-supply piping type and size. 1) Operation: Wheel handle.

d. Riser: 1) Size: NPS 1/2 (DN 15). 2) Material: ASME A112.18.6, braided- or corrugated-stainless-steel flexible

hose riser. 2.10 TOILET SEATS

A. Toilet Seats <Insert drawing designation>:

1. Manufacturers a. American Standard b. Bemis c. Church d. Eljer e. Kohler

2. Standard: IAPMO/ANSI Z124.5. 3. Material: Plastic. 4. Type: Residential. 5. Shape: Regular rim (Closed front). 6. Configuration: Closed front with cover. 7. Size: Regular. 8. Hinge Type: Check. 9. Hinge Material: Plastic. 10. Seat Cover: Not required. 11. Color: White.

2.11 SUPPLY FITTINGS



B. Standard: ASME A112.18.1/CSA B125.1. C. Lavatory, Kitchen Sink and Laundry Tray Supply Fittings:

1. Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching water-supply piping size. Include chrome-plated wall flange.

2. Stops: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with inlet connection matching water-supply piping type and size. a. Operation: Wheel handle.

3. Risers: a. Size: NPS 1/2 for lavatories. b. Size: NPS 3/8 for kitchen sinks and laundry trays. c. Material: ASME A112.18.6, braided- or corrugated-stainless-steel flexible hose ris-

er.

2.12 WASTE FITTINGS

A. Standard: ASME A112.18.2/CSA B125.2. B. Drain: Pop-up type with NPS 1-1/4 straight tailpiece as part of faucet for standard lavatories. C. Drain: Grid type with NPS 1-1/2 straight tailpiece for standard kitchen sinks and for laundry

trays. D. Trap:

1. Size: NPS 1-1/2 for lavatories. 2. Size: NPS 1-1/2 for kitchen sinks and laundry trays. 3. Material: ASTM F 409 PVC one-piece trap and waste to wall and wall flange.

2.13 GROUT

A. Standard: ASTM C 1107/C 1107M, Grade B, post-hardening and volume-adjusting, dry, hydrau-

lic-cement grout. B. Characteristics: Nonshrink; recommended for interior and exterior applications. C. Design Mix: 5000-psi (34.5-MPa), 28-day compressive strength. D. Packaging: Premixed and factory packaged.

PART 3 - EXECUTION 3.1 EXAMINATION

A. Examine roughing-in of water-supply and sanitary drainage and vent piping systems to verify

actual locations of piping connections before plumbing-fixture installation. B. Examine walls, floors, cabinets, and counters for suitable conditions where fixtures will be in-

stalled. C. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 INSTALLATION

A. Install plumbing fixtures level and plumb according to roughing-in drawings. B. Install floor-mounted water closets on closet flange attachments to drainage piping. C. Install counter-mounting fixtures in and attached to casework. D. Install water-supply piping with stop on each supply to each fixture to be connected to water

distribution piping. Attach supplies to supports or substrate within pipe spaces behind fixtures. Install stops in locations where they can be easily reached for operation.


1. Exception: Use ball or gate valves if supply stops are not specified with fixture. Comply with valve requirements specified in Section 220523.12 "Ball Valves for Plumbing Piping" and Section 220523.15 "Gate Valves for Plumbing Piping."

E. Install tanks for accessible, tank-type water closets with lever handle mounted on wide side of compartment.

F. Install toilet seats on water closets. G. Install faucet flow-control fittings with specified flow rates and patterns in faucet spouts if fau-

cets are not available with required rates and patterns. Include adapters if required. H. Install shower flow-control fittings with specified maximum flow rates in shower arms. I. Install traps on fixture outlets.

1. Exception: Omit trap on fixtures with integral traps. 2. Exception: Omit trap on indirect wastes unless otherwise indicated.

J. Set bathtubs in leveling bed of cement grout. K. Install wall flanges or escutcheons at piping wall penetrations in exposed, finished locations.

Use deep-pattern escutcheons if required to conceal protruding fittings. Comply with escutch-eon requirements specified in Section 220518 "Escutcheons for Plumbing Piping."

L. Seal joints between plumbing fixtures, counters, floors, and walls using sanitary-type, one-part, mildew-resistant silicone sealant. Match sealant color to fixture color. Comply with sealant re-quirements specified in Section 079200 "Joint Sealants."

3.3 CONNECTIONS

A. Connect fixtures with water supplies, stops, and risers, and with traps, soil, waste, and vent piping. Use size fittings required to match fixtures.

B. Comply with water piping requirements specified in Section 221116 "Domestic Water Piping." C. Comply with soil and waste piping requirements specified in Section 221316 "Sanitary Waste

and Vent Piping." D. Install protective shielding pipe covers and enclosures on exposed supplies and waste piping of

accessible lavatories and sinks. Comply with requirements in Section 220719 "Plumbing Piping Insulation."

3.4 ADJUSTING

A. Operate and adjust plumbing fixtures and controls. Replace damaged and malfunctioning fix-tures, fittings, and controls.

B. Adjust water pressure at faucets to produce proper flow.


A. After completing installation of plumbing fixtures, inspect and repair damaged finishes. B. Clean plumbing fixtures, faucets, and other fittings with manufacturers' recommended cleaning

methods and materials. C. Provide protective covering for installed plumbing fixtures and fittings. D. Do not allow use of plumbing fixtures for temporary facilities unless approved in writing by

Owner.


BASIC ELECTRICAL MATERIALS AND METHODS 26 0500 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

SECTION 26 0500 - BASIC ELECTRICAL MATERIALS AND METHODS

PART 1 - GENERAL



1.2 SUMMARY

A. This Section includes the following:

1. Supporting devices for electrical components. 2. Electricity-metering components. 3. Cutting and patching for electrical construction. 4. Touchup painting.

1.3 SUBMITTALS

A. Product Data: For electricity-metering equipment.

B. Shop Drawings: Dimensioned plans and sections or elevation layouts of electricity-metering equipment.

C. Field Test Reports: Indicate and interpret test results for compliance with performance requirements.

D. Lamp Schedule: Provide a comprehensive table of replacement lamps for all exterior and interior light fixtures showing fixture designation, location, lamp watts/volts, lamp description, manufacturer and ordering code, and package count.


A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use.

B. Comply with NFPA 70.

1.5 COORDINATION

A. Coordinate chases, slots, inserts, sleeves, and openings with general construction work and arrange in building structure during progress of construction to facilitate the electrical installations that follow.


1. Set inserts and sleeves in masonry work, and other structural components as they are constructed.

B. Sequence, coordinate, and integrate installing electrical materials and equipment for efficient flow of the Work. Coordinate installing large equipment requiring positioning before closing in the building.

C. Coordinate electrical service connections to components furnished by Utility companies.

1. Coordinate installation and connection of exterior underground and overhead utilities and services, including provision for electricity-metering components.

2. Comply with requirements of authorities having jurisdiction and of Utility Company providing electrical power and other services.

D. Coordinate location of access panels and doors for electrical items that are concealed by finished surfaces with the appropriate trade contractor. Access doors and panels are specified in Division 08 Section "Access Doors and Panels."

E. Where electrical identification devices are applied to field-finished surfaces, coordinate installation of identification devices with completion of finished surface.

F. Where electrical identification markings and devices will be concealed by acoustical ceilings and similar finishes, coordinate installation of these items before ceiling installation.

PART 2 - PRODUCTS

2.1 SUPPORTING DEVICES

A. Material: Cold-formed steel, with corrosion-resistant coating acceptable to authorities having jurisdiction.

B. Metal Items for Use Outdoors or in Damp Locations: Hot-dip galvanized steel.

C. Slotted-Steel Channel Supports: Flange edges turned toward web, and 9/16-inch- (14-mm-) diameter slotted holes at a maximum of 2 inches (50 mm) o. c., in webs.

D. Raceway and Cable Supports: Manufactured clevis hangers, riser clamps, straps, threaded C-clamps with retainers, ceiling trapeze hangers, wall brackets, and spring-steel clamps or click-type hangers.

E. Pipe Sleeves: ASTM A 53, Type E, Grade A, Schedule 40, galvanized steel, plain ends.

F. Cable Supports for Vertical Conduit: Factory-fabricated assembly consisting of threaded body and insulating wedging plug for non-armored electrical cables in riser conduits. Plugs have number and size of conductor gripping holes as required to suit individual risers. Body constructed of malleable-iron casting with hot-dip galvanized finish.

G. Expansion Anchors: Carbon-steel wedge or sleeve type.

H. Toggle Bolts: All-steel springhead type.


I. Powder-Driven Threaded Studs: Heat-treated steel.

2.2 EQUIPMENT FOR UTILITY COMPANY'S ELECTRICITY METERING

A. Current-Transformer Cabinets: Comply with requirements of electrical power utility company.

B. Meter Sockets: Comply with requirements of electrical power utility company.

2.3 TOUCHUP PAINT

A. For Equipment: Equipment manufacturer's paint selected to match installed equipment finish.

B. Galvanized Surfaces: Zinc-rich paint recommended by item manufacturer.

PART 3 - EXECUTION

3.1 ELECTRICAL EQUIPMENT INSTALLATION

A. Headroom Maintenance: If mounting heights or other location criteria are not indicated, arrange and install components and equipment to provide the maximum possible headroom.

B. Materials and Components: Install level, plumb, and parallel and perpendicular to other building systems and components, unless otherwise indicated.

C. Equipment: Install to facilitate service, maintenance, and repair or replacement of components. Connect for ease of disconnecting, with minimum interference with other installations.

D. Right of Way: Give to raceways and piping systems installed at a required slope.

E. Comply with working clearances and dedicated spaces per NEC Articles 110, 384, and 800-5, as well as all current NEC Articles, Federal, State and Local regulation.

F. Relocate any improperly located equipment or device, and replace any incorrect connection caused by lack of coordination or preparation. Repair to the satisfaction of the Owner and Architect any hole, etc. caused by these relocations/replacements at no additional cost to the Owner.

3.2 ELECTRICAL SUPPORTING DEVICE APPLICATION

A. Damp Locations and Outdoors: Hot-dip galvanized materials or nonmetallic, U-channel system components.

B. Dry Locations: Steel materials.

C. Support Clamps for PVC Raceways: Click-type clamp system.

D. Selection of Supports: Comply with manufacturer's written instructions.


E. Strength of Supports: Adequate to carry present and future loads, times a safety factor of at least four; minimum of 200-lb (90-kg) design load.

3.3 SUPPORT INSTALLATION

A. Install support devices to securely and permanently fasten and support electrical components.

B. Install individual and multiple raceway hangers and riser clamps to support raceways. Provide U-bolts, clamps, attachments, and other hardware necessary for hanger assemblies and for securing hanger rods and conduits.

C. Support parallel runs of horizontal raceways together on trapeze- or bracket-type hangers.

D. Size supports for multiple raceway installations so capacity can be increased by a 25 percent minimum in the future.

E. Support individual horizontal raceways with separate, malleable-iron pipe hangers or clamps.

F. Install 1/4-inch- (6-mm-) diameter or larger threaded steel hanger rods, unless otherwise indicated.

G. Spring-steel fasteners specifically designed for supporting single conduits or tubing may be used instead of malleable-iron hangers for 1-1/2-inch (38-mm) and smaller raceways serving lighting and receptacle branch circuits above suspended ceilings and for fastening raceways to slotted channel and angle supports.

H. Arrange supports in vertical runs so the weight of raceways and enclosed conductors is carried entirely by raceway supports, with no weight load on raceway terminals.

I. Simultaneously install vertical conductor supports with conductors.

J. Separately support cast boxes that are threaded to raceways and used for fixture support. Support sheet-metal boxes directly from the building structure or by bar hangers. If bar hangers are used, attach bar to raceways on opposite sides of the box and support the raceway with an approved fastener not more than 24 inches (610 mm) from the box.

K. Install metal channel racks for mounting cabinets, panelboards, disconnect switches, control enclosures, pull and junction boxes, and transformers.

L. Install sleeves for cable and raceway penetrations of concrete slabs and walls unless core-drilled holes are used. Install sleeves for cable and raceway penetrations of masonry and fire-rated gypsum walls and of all other fire-rated floor and wall assemblies. Securely fasten electrical items and their supports to the building structure, unless otherwise indicated. Perform fastening according to the following unless other fastening methods are indicated:

1. Wood: Fasten with wood screws or screw-type nails. 2. Masonry: Toggle bolts on hollow masonry units and expansion bolts on solid masonry

units. 3. Instead of expansion bolts, threaded studs driven by a powder charge and provided with

lock washers may be used in existing concrete. 4. Steel: Welded threaded studs or spring-tension clamps on steel.


a. Field Welding: Comply with AWS D1.1.

5. Welding to steel structure may be used only for threaded studs, not for conduits, pipe straps, or other items.

6. Light Steel: Sheet-metal screws. 7. Fasteners: Select so the load applied to each fastener does not exceed 25 percent of its

proof-test load.

3.4 UTILITY COMPANY ELECTRICITY-METERING EQUIPMENT

A. Install equipment according to utility company's written requirements. Provide grounding and empty conduits as required by Utility Company.

3.5 FIRE-STOPPING

A. Apply fire-stopping to cable and raceway penetrations of fire-rated floor and wall assemblies to achieve fire-resistance rating of the assembly. Fire-stopping materials and installation requirements are specified in Division 07 Section "Firestopping."

3.6 CUTTING AND PATCHING

A. Cut, channel, chase, and drill floors, walls, partitions, ceilings, and other surfaces required to permit electrical installations. Perform cutting by skilled mechanics of trades involved.

B. Repair and refinish disturbed finish materials and other surfaces to match adjacent undisturbed surfaces. Repair and refinish materials and other surfaces by skilled mechanics of trades involved.

C. Provide access panels and doors for electrical items that are concealed by finished surfaces. Access panels and doors shall be located so that junction boxes, pull boxes, etc. are easily accessible for maintenance.


A. Inspect installed components for damage and faulty work, including the following:

1. Supporting devices for electrical components. 2. Electricity-metering components. 3. Cutting and patching for electrical construction. 4. Touchup painting.

3.8 REFINISHING AND TOUCHUP PAINTING

A. Refinish and touch up paint. Paint materials and application requirements are specified in Division 09 Section "Painting."


1. Clean damaged and disturbed areas and apply primer, intermediate, and finish coats to suit the degree of damage at each location.

2. Follow paint manufacturer's written instructions for surface preparation and for timing and application of successive coats.

3. Repair damage to galvanized finishes with zinc-rich paint recommended by manufacturer. 4. Repair damage to PVC or paint finishes with matching touchup coating recommended by

manufacturer.


A. On completion of installation, including outlets, fittings, and devices, inspect exposed finish. Remove burrs, dirt, paint spots, and construction debris.

B. Protect equipment and installations and maintain conditions to ensure that coatings, finishes, and cabinets are without damage or deterioration at time of Project Completion.

END OF SECTION

Copyright 2015 AIA MasterSpec Premium 12/15

WIRING DEVICES 26 2726 - 1 SMHA Scattered Site Renovation 2017349.01 March 01, 2017

WIRING DEVICES 262726 - 1

SECTION 26 2726 - WIRING DEVICES

TIPS:

To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-File Formatting/Toggle/Editor's Notes.

To read detailed research, technical information about products and materials, and coordina-tion checklists, click on MasterWorks/Supporting Information.

PART 1 - GENERAL



1.2 SUMMARY


1. Straight-blade convenience, hospital-grade, isolated-ground, and tamper-resistant receptacles.

2. USB charger devices. 3.2. GFCI receptacles. 4. SPD receptacles. 5. Hazardous (classified) location receptacles. 6. Twist-locking receptacles. 7. Pendant cord-connector devices. 8. Cord and plug sets. 9.3. Toggle switches. 10. Decorator-style convenience. 11. Wall switch sensor light switches with dual technology sensors. 12. Wall switch sensor light switches with passive infrared sensors. 13. Wall switch sensor light switches with ultrasonic sensors. 14. Digital timer light switches. 15.4. Residential devices. 16. Wall-box dimmers. 17.5. Wall plates. 18. Floor service outlets. 19. Poke-through assemblies. 20. Prefabricated multioutlet assemblies. 21. Service poles.

Formatted: Font: (Default) Tahoma, 10 pt









1.3 DEFINITIONS

A. Abbreviations of Manufacturers' Names:

1. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc. 2. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems. 3. Leviton: Leviton Mfg. Company, Inc. 4. Pass & Seymour: Pass& Seymour/Legrand.

B. BAS: Building automation system.

C.B. EMI: Electromagnetic interference.

D.C. GFCI: Ground-fault circuit interrupter.

E.D. Pigtail: Short lead used to connect a device to a branch-circuit conductor.

F. RFI: Radio-frequency interference.

G. SPD: Surge protective device.

H. UTP: Unshielded twisted pair.



B. Shop Drawings: List of legends and description of materials and process used for premarking wall plates.

C. Samples: One for each type of device and wall plate specified, in each color specified.


A. Field quality-control reports.


A. Operation and Maintenance Data: For wiring devices to include in all manufacturers' packing-label warnings and instruction manuals that include labeling conditions.






1. Service/Power Poles: [One for every 10] <Insert quantities>, but no fewer than [one] <Insert number>.

2. Floor Service-Outlet Assemblies: [One for every 10] <Insert quantities>, but no fewer than [one] <Insert number>.

3. Poke-Through, Fire-Rated Closure Plugs: [One for every five] <Insert quantities> floor service outlets installed, but no fewer than [two] <Insert number>.

4. SPD Receptacles: [One for every 10] <Insert quantities> of each type installed, but no fewer than [two of each type] <Insert number>.

PART 2 - PRODUCTS

2.1 GENERAL WIRING-DEVICE REQUIREMENTS

A. Wiring Devices, Components, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.


C. Devices that are manufactured for use with modular plug-in connectors may be substituted under the following conditions:

1. Connectors shall comply with UL 2459 and shall be made with stranding building wire. 2. Devices shall comply with the requirements in this Section.

D. Devices for Owner-Furnished Equipment:

1. Receptacles: Match plug configurations. 2. Cord and Plug Sets: Match equipment requirements.

E. Source Limitations: Obtain each type of wiring device and associated wall plate from single source from single manufacturer.

2.2 STRAIGHT-BLADE RECEPTACLES

A. Duplex Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.


1. <Double click here to find, evaluate, and insert list of manufacturers and products.>

B. Hospital-Grade, Duplex Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498 Supplement sd, and FS W-C-596.







1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Single-piece, rivetless, nickel-plated, all-brass grounding system. Nickel-

plated, brass mounting strap.

C. Isolated-Ground, Duplex Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Straight blade; equipment grounding contacts shall be connected only to the

green grounding screw terminal of the device and with inherent electrical isolation from mounting strap. Isolation shall be integral to receptacle construction and not dependent on removable parts.

D.B. Tamper-Resistant Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.


1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2.5. Description: Labeled and complying with NFPA 70, "Health Care Facilities" Article,

"Pediatric Locations" Section.

2.3 USB CHARGER DEVICES

A. Tamper-Resistant, USB Charger Receptacles: 12 V dc, 2.0 A, USB Type A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, UL 1310, and FS W-C-596.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Single-piece, rivetless, nickel-plated, all-brass grounding system. Nickel-

plated, brass mounting strap. 3. USB Receptacles: [Single] [Dual] [Quad], Type A. 4. Line Voltage Receptacles: [Single] [Dual], two pole, three wire, and self-grounding.

B. Hospital-Grade, USB Charger Receptacles: 12 V dc, 2.0 A, USB Type A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498 Supplement sd, UL 1310, and FS W-C-596.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Labeled and complying with NFPA 70, "Health Care Facilities" Article,

"Pediatric Locations" Section. 3. USB Receptacles: [Single] [Dual] [Quad], Type A. 4. Line Voltage Receptacles: [Single] [Dual], two pole, three wire, and self-grounding.



















2.42.3 GFCI RECEPTACLES

A. General Description:

1. 125 V, 20 A, straight blade, [feed] [non-feed]-through type. 2. Comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, UL 943 Class A, and

FS W-C-596. 3. Include indicator light that shows when the GFCI has malfunctioned and no longer

provides proper GFCI protection.

B. Duplex GFCI Convenience Receptacles:



C. Tamper-Resistant, Duplex GFCI Convenience Receptacles:

1. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc. 2. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems. 3. Leviton: Leviton Mfg. Company, Inc. 1. Pass & Seymour: Pass& Seymour/Legrand <Double click here to find, evaluate, and

insert list of manufacturers and products.> D. Hospital-Grade, Duplex GFCI Convenience Receptacles: Comply with UL 498

Supplement sd. 1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2.5 SPD RECEPTACLES See "Surge Protective Device (SPD) Receptacles" Article in the Evaluations for

information on SPD ratings. A. General Description: Comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498,

UL 1449, and FS W-C-596, with integral SPD in line to ground, line to neutral, and neutral to ground.

1. 125 V, 20 A, straight-blade type. 2. SPD Components: Multiple metal-oxide varistors; with a nominal clamp-level rating of

400 V and minimum single transient pulse energy dissipation of 240 J, according to IEEE C62.41.2 and IEEE C62.45.

3. Active SPD Indication: Visual and audible, with light visible in face of device to indicate device is "active" or "no longer in service."

B. Duplex SPD Convenience Receptacles: 1. <Double click here to find, evaluate, and insert list of manufacturers and products.> C. Isolated-Ground, Duplex SPD Convenience Receptacles: 1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Grounding: Equipment grounding contacts shall be connected only to the green

grounding screw terminal of the device and with inherent electrical isolation from mounting strap. Isolation shall be integral to receptacle construction and not dependent on removable parts.

Formatted: Font: (Default) Tahoma, 10 pt, Not Bold




Formatted: Space Before: 0 pt



Formatted: PR2




Formatted: PR2


Formatted: PR2




Formatted: PR2













D. Hospital-Grade, Duplex SPD Convenience Receptacles: Comply with UL 498 Supplement sd.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> E. Isolated-Ground Hospital-Grade Duplex SPD Convenience Receptacles: Comply with

UL 498 Supplement sd. 1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Grounding: Equipment grounding contacts shall be connected only to the green


2.6 HAZARDOUS (CLASSIFIED) LOCATION RECEPTACLES A. Hazardous (Classified) Locations Receptacles: Comply with NEMA FB 11 and UL 1010. 1.4. <Double click here to find, evaluate, and insert list of manufacturers and products.>

2.7 TWIST-LOCKING RECEPTACLES

A. Twist-Lock, Single Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration L5-20R, and UL 498.


B. Twist-Lock, Isolated-Ground, Single Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration L5-20R, and UL 498.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Grounding: Equipment grounding contacts shall be connected only to the green


2.8 PENDANT CORD-CONNECTOR DEVICES

A. Description:

1. Matching, locking-type plug and receptacle body connector. 2. NEMA WD 6 Configurations L5-20P and L5-20R, heavy-duty grade, and FS W-C-596. 3. Body: Nylon, with screw-open, cable-gripping jaws and provision for attaching external

cable grip. 4. External Cable Grip: Woven wire-mesh type made of high-strength, galvanized-steel wire

strand, matched to cable diameter, and with attachment provision designed for corresponding connector.

2.9 CORD AND PLUG SETS

A. Description:

Formatted: PR2




Formatted: PR2




Formatted: PR2
















1. Match voltage and current ratings and number of conductors to requirements of equipment being connected.

2. Cord: Rubber-insulated, stranded-copper conductors, with Type SOW-A jacket; with green-insulated grounding conductor and ampacity of at least 130 percent of the equipment rating.

3. Plug: Nylon body and integral cable-clamping jaws. Match cord and receptacle type for connection.

2.102.4 TOGGLE SWITCHES

A. Comply with NEMA WD 1, UL 20, and FS W-S-896.

B. Switches, 120/277 V, 20 A:

1. Single Pole, three way, four way:

a. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc.

b. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems.

c. Leviton: Leviton Mfg. Company, Inc.

d. Pass & Seymour: Pass& Seymour/Legrand.

a. <Double click here to find, evaluate, and insert list of manufacturers and products.>

2. Two Pole:


3. Three Way:


4. Four Way:


C. Pilot-Light Switches: 120/277 V, 20 A.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Single pole, with LED-lighted handle, illuminated when switch is off.

D. Key-Operated Switches: 120/277 V, 20 A.


Formatted: PR3, Space Before: 12 pt














1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Single pole, with factory-supplied key in lieu of switch handle.

E. Single-Pole, Double-Throw, Momentary-Contact, Center-off Switches: 120/277 V, 20 A; for use with mechanically held lighting contactors.


F. Key-Operated, Single-Pole, Double-Throw, Momentary-Contact, Center-off Switches: 120/277 V, 20 A; for use with mechanically held lighting contactors, with factory-supplied key in lieu of switch handle.


2.11 DECORATOR-STYLE DEVICES

A. Convenience Receptacles: Square face, 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, and UL 498.


B. Tamper-Resistant Convenience Receptacles: Square face, 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, and UL 498.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: Labeled to comply with NFPA 70, "Receptacles, Cord Connectors, and

Attachment Plugs (Caps)" Article, "Tamper-Resistant Receptacles in Dwelling Units" Section.

C. Tamper-Resistant and Weather-Resistant Convenience Receptacles: Square face, 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, and UL 498.


Attachment Plugs (Caps)" Article, "Tamper-Resistant Receptacles in Dwelling Units" Section, when installed in wet and damp locations.

D. GFCI, [Feed] [Non-Feed]-Through Type, Convenience Receptacles: Square face, 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, UL 498, and UL 943 Class A.


E. GFCI, Tamper-Resistant and Weather-Resistant Convenience Receptacles: Square face, 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, UL 498, and UL 943 Class A.

































2. Description: Labeled to comply with NFPA 70, "Receptacles, Cord Connectors, and Attachment Plugs (Caps)" Article, "Tamper-Resistant Receptacles in Dwelling Units" Section.

F. Toggle Switches: Square Face, 120/277 V, 15 A; comply with NEMA WD 1, UL 20, and FS W-S-896.


G. Lighted Toggle Switches: Square Face, 120 V, 15 A; comply with NEMA WD 1 and UL 20.

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2. Description: With LED-lighted handle, illuminated when switch is off.

2.12 WALL SWITCH SENSOR LIGHT SWITCH, DUAL TECHNOLOGY

A. <Double click here to find, evaluate, and insert list of manufacturers and products.>

B. Description: Switchbox-mounted, combination lighting-control sensor and conventional switch lighting-control unit using dual technology.

1. Connections: Provisions for connection to BAS. 2. Connections: Hard wired. 3. Connections: Wireless. 4. Rated 960 W at 120-V ac for tungsten lighting, 10 A at 120-V ac or 10 A at 277-V ac for

fluorescent or LED lighting, and 1/4 hp at 120-V ac. 5. Integral relay for connection to BAS. 6. Adjustable time delay of [five] [10] [15] [20] minutes. 7. Able to be locked to [Automatic-On] [Manual-On] mode. 8. Automatic Light-Level Sensor: Adjustable from 2 to 200 fc (21.5 to 2152 lux). 9. Comply with NEMA WD 1, UL 20, and FS W-S-896.

2.13 WALL SWITCH SENSOR LIGHT SWITCH, PASSIVE INFRARED


B. Description: Switchbox-mounted, combination, lighting-control sensor and conventional switch lighting-control unit using passive infrared technology.


fluorescent or LED lighting, and 1/4 hp at 120-V ac. 5. Integral relay for connection to BAS. 6. Adjustable time delay of [five] [10] [15] [20] minutes.















7. Able to be locked to [Automatic-On] [Manual-On] mode. 8. Automatic Light-Level Sensor: Adjustable from 2 to 200 fc (21.5 to 2152 lux). 9. Comply with NEMA WD 1, UL 20, and FS W-S-896.

2.14 WALL SWITCH SENSOR LIGHT SWITCH, ULTRASONIC


B. Description: Switchbox-mounted, combination, lighting-control sensor and conventional switch lighting-control unit using ultrasonic technology.


fluorescent or LED lighting, and 1/4 hp at 120-V ac. 5. Integral relay for connection to BAS. 6. Adjustable time delay of [five] [10] [15] [20] minutes. 7. Able to be locked to [Automatic-On] [Manual-On] mode. 8. Automatic Light-Level Sensor: Adjustable from 2 to 200 fc (21.5 to 2152 lux). 9. Comply with NEMA WD 1, UL 20, and FS W-S-896.

2.15 DIGITAL TIMER LIGHT SWITCH


B. Description: Switchbox-mounted, combination digital timer and conventional switch lighting-control unit, with backlit digital display, with selectable time interval in [10] [20]-minute increments.

1. Rated 960 W at 120-V ac for tungsten lighting, 10 A at 120-V ac or 10 A at 277-V ac for fluorescent or LED lighting, and 1/4 hp at 120-V ac.

2. Integral relay for connection to BAS.

2.162.5 RESIDENTIAL DEVICES

A. Residential-Grade, Tamper-Resistant Convenience Receptacles: 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, and UL 498.


Attachment Plugs (Caps)" Article, "Tamper-Resistant Receptacles in Dwelling Units" Section.















B. Weather-Resistant and Tamper-Resistant Convenience Receptacles: 125 V, 15 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-15R, and UL 498.


Attachment Plugs (Caps)" Article, "Tamper-Resistant Receptacles in Dwelling Units" Section, when installed in wet and damp locations.

C. Fan-Speed Controls:

1. Modular, 120-V, full-wave, solid-state units with integral, quiet on-off switches and audible frequency and EMI/RFI filters.

2. Comply with UL 1917. 3. Continuously adjustable [slider] [toggle switch] [rotary knob], [5] [1.5] A. 4. Three-speed adjustable [slider] [rotary knob], 1.5 A.

D.A. Telephone Outlet:

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2.1. Description: Single RJ-45 jack for terminating Cabling[Category 5e], twisted pair cable

complying with Section 260523 "Control-Voltage Electrical Power Conductors." 3. Description: Single RJ-45 jack for terminating [Category 5e], twisted pair cable

complying with Section 271513 "Communications Copper Horizontal Cabling." 4.2. Comply with UL 1863.

E.B. Combination TV and Telephone Outlet:

1. <Double click here to find, evaluate, and insert list of manufacturers and products.> 2.1. Description: Single RJ-45 jack for terminating [Category 5e], twisted pair cable

complying with Section 260523 "Control-Voltage Electrical Power Cables" and a single BNC connector for terminating coaxial cable.

3. Description: Single RJ-45 jack for terminating [Category 5e], twisted pair cable complying with Section 271513 "Communications Copper Horizontal Cabling" and a single BNC connector for terminating coaxial cable complying with Section 271533 "Communications Coaxial Horizontal Cabling."

4.2. Comply with UL 1863.

2.172.6 WALL-BOX DIMMERS

A. Dimmer Switches: Modular, full-wave, solid-state units with integral, quiet on-off switches, with audible frequency and EMI/RFI suppression filters.

B. Control: Continuously adjustable [slider] [toggle switch] [rotary knob]; with single-pole or three-way switching. Comply with UL 1472.

C. Incandescent Lamp Dimmers: 120 V; control shall follow square-law dimming curve. On-off switch positions shall bypass dimmer module.




















1. 600 W; dimmers shall require no derating when ganged with other devices..[ Illuminated when "off."]

2. <Insert wattage ratings and descriptions>.

D. Fluorescent Lamp Dimmer Switches: Modular; compatible with dimmer ballasts; trim potentiometer to adjust low-end dimming; dimmer-ballast combination capable of consistent dimming with low end not greater than 20 percent of full brightness.

E. LED Lamp Dimmer Switches: Modular; compatible with LED lamps; trim potentiometer to adjust low-end dimming; capable of consistent dimming with low end not greater than 20 percent of full brightness.

2.182.7 WALL PLATES

A. Single and combination types shall match corresponding wiring devices.

1. Plate-Securing Screws: Metal with head color to match plate finish. 2. Material for Finished Spaces: [Steel with white baked enamel, suitable for field painting]

[Smooth, high-impact thermoplastic] [0.035-inch- (1-mm-) thick, satin-finished, Type 302 stainless steel] [0.04-inch- (1-mm-) thick, brushed brass with factory polymer finish] [0.05-inch- (1.2-mm-) thick, anodized aluminum] [0.04-inch- (1-mm-) thick steel with chrome-plated finish].

3. Material for Unfinished Spaces: [Galvanized steel] [Smooth, high-impact thermoplastic]. 4. Material for Damp Locations: [Thermoplastic ] [Cast aluminum] with spring-loaded lift

cover, and listed and labeled for use in wet and damp locations.

B. Wet-Location, Weatherproof Cover Plates: NEMA 250, complying with Type 3R, weather-resistant [, die-cast aluminum] [thermoplastic] with lockable cover.

2.19 FLOOR SERVICE FITTINGS

A. Type: Modular, [flush-type] [flap-type] [above-floor], dual-service units suitable for wiring method used.

B. Compartments: Barrier separates power from voice and data communication cabling.

C. Service Plate: [Rectangular] [Round], [die-cast aluminum] [solid brass] with satin finish.

D. Power Receptacle: NEMA WD 6 Configuration 5-20R, gray finish, unless otherwise indicated.

E. Data Communication Outlet: [Blank cover with bushed cable opening.] [Two modular, keyed, color-coded, RJ-45 jacks for twisted pair cable complying with requirements in Section 271513 "Communications Copper Horizontal Cabling."]




































2.20 POKE-THROUGH ASSEMBLIES


B. Description:

1. Factory-fabricated and -wired assembly of below-floor junction box with multichanneled, through-floor raceway/firestop unit and detachable matching floor service-outlet assembly.

2. Comply with UL 514 scrub water exclusion requirements. 3. Service-Outlet Assembly: [Pedestal type with services indicated] [Flush type with

two simplex receptacles and space for two RJ-45 jacks] [Flush type with four simplex receptacles and space for four RJ-45 jacks] complying with requirements in Section 271513 "Communications Copper Horizontal Cabling."

4. Size: Selected to fit nominal [3-inch (75-mm)] [4-inch (100-mm)] cored holes in floor and matched to floor thickness.

5. Fire Rating: Unit is listed and labeled for fire rating of floor-ceiling assembly. 6. Closure Plug: Arranged to close unused [3-inch (75-mm)] [4-inch (100-mm)] cored

openings and reestablish fire rating of floor. 7. Wiring Raceways and Compartments: For a minimum of four No. 12 AWG conductors and

a minimum of [two] [four], four-pair cables that comply with requirements in Section 271513 "Communications Copper Horizontal Cabling."

2.21 PREFABRICATED MULTIOUTLET ASSEMBLIES


B. Description:

1. Two-piece surface metal raceway, with factory-wired multioutlet harness. 2. Components shall be products from single manufacturer designed for use as a complete,

matching assembly of raceways and receptacles.

C. Raceway Material: [Metal, with manufacturer's standard finish] [PVC].

D. Multioutlet Harness:

1. Receptacles: 15-A, 125-V, NEMA WD 6 Configuration 5-15R receptacles complying with NEMA WD 1, UL 498, and FS W-C-596.

2. Receptacle Spacing: [6 inches (150 mm)] [9 inches (230 mm)] [12 inches (300 mm)] [18 inches (460 mm)].

3. Wiring: No. 12 AWG solid, Type THHN copper, [single circuit] [two circuit, connecting alternating receptacles].






























2.22 SERVICE POLES

A. Description:

1. Factory-assembled and -wired units to extend power and voice and data communication from distribution wiring concealed in ceiling to devices or outlets in pole near floor.

2. Poles: Nominal 2.5-inch- (65-mm-) square cross section, with height adequate to extend from floor to at least 6 inches (150 mm) above ceiling, and with separate channels for power wiring and voice and data communication cabling.

3. Mounting: Ceiling trim flange with concealed bracing arranged for positive connection to ceiling supports; with pole foot and carpet pad attachment.

4. Finishes: [Manufacturer's standard painted finish and trim combination] [Satin-anodized aluminum].

5. Wiring: Sized for minimum of five No. 12 AWG power and ground conductors and a minimum of four, four-pair, Category 3 or Category 5 voice and data communication cables.

6. Power Receptacles: Two duplex, 20-A, straight-blade receptacles complying with requirements in this Section.

7. Data Communication Outlets: [Blank insert with bushed cable opening] [Two RJ-45 jacks] [Four RJ-45 jacks] complying with requirements in Section 271513 "Communications Copper Horizontal Cabling."

2.232.8 FINISHES

A. Device Color:

1. Wiring Devices Connected to Normal Power System: [Almond] [Black] [Brown] [Gray] [Ivory] [White ] [As selected by Architect] <Insert color> unless otherwise indicated or required by NFPA 70 or device listing.

2. Wiring Devices Connected to Emergency Power System: [Red] <Insert color>. 3. SPD Devices: Blue. 4. Isolated-Ground Receptacles: [Orange] [As specified above, with orange triangle

on face].

B. Wall Plate Color: For plastic covers, match device color.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Comply with NECA 1, including mounting heights listed in that standard, unless otherwise indicated.

B. Coordination with Other Trades:






















1. Protect installed devices and their boxes. Do not place wall finish materials over device boxes and do not cut holes for boxes with routers that are guided by riding against outside of boxes.

2. Keep outlet boxes free of plaster, drywall joint compound, mortar, cement, concrete, dust, paint, and other material that may contaminate the raceway system, conductors, and cables.

3. Install device boxes in brick or block walls so that the cover plate does not cross a joint unless the joint is troweled flush with the face of the wall.

4. Install wiring devices after all wall preparation, including painting, is complete.

C. Conductors:

1. Do not strip insulation from conductors until right before they are spliced or terminated on devices.

2. Strip insulation evenly around the conductor using tools designed for the purpose. Avoid scoring or nicking of solid wire or cutting strands from stranded wire.

3. The length of free conductors at outlets for devices shall meet provisions of NFPA 70, Article 300, without pigtails.

4. Existing Conductors:

a. Cut back and pigtail, or replace all damaged conductors. b. Straighten conductors that remain and remove corrosion and foreign matter. c. Pigtailing existing conductors is permitted, provided the outlet box is large enough.

D. Device Installation:

1. Replace devices that have been in temporary use during construction and that were installed before building finishing operations were complete.

2. Keep each wiring device in its package or otherwise protected until it is time to connect conductors.

3. Do not remove surface protection, such as plastic film and smudge covers, until the last possible moment.

4. Connect devices to branch circuits using pigtails that are not less than 6 inches (152 mm) in length.

5. When there is a choice, use side wiring with binding-head screw terminals. Wrap solid conductor tightly clockwise, two-thirds to three-fourths of the way around terminal screw.

6. Use a torque screwdriver when a torque is recommended or required by manufacturer. 7. When conductors larger than No. 12 AWG are installed on 15- or 20-A circuits, splice

No. 12 AWG pigtails for device connections. 8. Tighten unused terminal screws on the device. 9. When mounting into metal boxes, remove the fiber or plastic washers used to hold

device-mounting screws in yokes, allowing metal-to-metal contact.

E. Receptacle Orientation:

1. Install ground pin of vertically mounted receptacles [up] [down], and on horizontally mounted receptacles to the [right] [left].















2. Install hospital-grade receptacles in patient-care areas with the ground pin or neutral blade at the top.

F. Device Plates: Do not use oversized or extra-deep plates. Repair wall finishes and remount outlet boxes when standard device plates do not fit flush or do not cover rough wall opening.

G. Dimmers:

1. Install dimmers within terms of their listing. 2. Verify that dimmers used for fan-speed control are listed for that application. 3. Install unshared neutral conductors on line and load side of dimmers according to

manufacturers' device listing conditions in the written instructions.

H. Arrangement of Devices: Unless otherwise indicated, mount flush, with long dimension vertical and with grounding terminal of receptacles on top. Group adjacent switches under single, multigang wall plates.

I. Adjust locations of floor service outlets and service poles to suit arrangement of partitions and furnishings.

3.2 GFCI RECEPTACLES

A. Install non-feed-through-type GFCI receptacles where protection of downstream receptacles is not required.

3.3 IDENTIFICATION

A. Comply with Section 260553 "Identification for Electrical Systems."

B. Identify each receptacle with panelboard identification and circuit number. Use hot, stamped, or engraved machine printing with [black] [white] [red]-filled lettering on face of plate, and durable wire markers or tags inside outlet boxes.

3.43.3 FIELD QUALITY CONTROL

A. Test Instruments: Use instruments that comply with UL 1436.

B. Test Instrument for Convenience Receptacles: Digital wiring analyzer with digital readout or illuminated digital-display indicators of measurement.

C. Perform the following tests and inspections[ with the assistance of a factory-authorized service representative]:

1. In healthcare facilities, prepare reports that comply with recommendations in NFPA 99. 2.1. Test Instruments: Use instruments that comply with UL 1436.




3.2. Test Instrument for Convenience Receptacles: Digital wiring analyzer with digital readout or illuminated digital-display indicators of measurement.

D. Tests for Convenience Receptacles:

1. Line Voltage: Acceptable range is 105 to 132 V. 2. Percent Voltage Drop under 15-A Load: A value of 6 percent or higher is unacceptable. 3. Ground Impedance: Values of up to 2 ohms are acceptable. 4. GFCI Trip: Test for tripping values specified in UL 1436 and UL 943. 5. Using the test plug, verify that the device and its outlet box are securely mounted. 6. Tests shall be diagnostic, indicating damaged conductors, high resistance at the circuit

breaker, poor connections, inadequate fault current path, defective devices, or similar problems. Correct circuit conditions, remove malfunctioning units and replace with new ones, and retest as specified above.

E. Test straight-blade [convenience outlets in patient-care areas] [hospital-grade convenience outlets] for the retention force of the grounding blade according to NFPA 99. Retention force shall be not less than 4 oz. (115 g).

F. Wiring device will be considered defective if it does not pass tests and inspections.

G. Prepare test and inspection reports.

END OF SECTION 262726




INTERIOR LIGHTING 26 5113 - 1 SMHA Scattered Site Renovation 2017349.0 March 01, 2017

SECTION 26 5113 - INTERIOR LIGHTING

PART 1 - GENERAL



1.2 SUMMARY


1. Interior luminaires and lamps. 2. Luminaire supports.

1.3 DEFINITIONS

A. CCT: Correlated Color Temperature.

B. CRI: Color Rendering Index.

C. Lumen: Measured output of lamp and luminaire, or both.

D. Luminaire: Complete lighting unit, including lamp, reflector, and housing.



1. Arrange in order of luminaire designation. 2. Include data on features, accessories, and finishes. 3. Include physical description and dimensions of luminaires. 4. Include battery and charger data for emergency lighting units. 5. Include life, output (lumens, CCT, and CRI), and energy efficiency data. 6. Include photometric data and adjustment factors based on laboratory tests, complying

with IES LM-45, for each luminaire type.

a. Manufacturers' Certified Data: Photometric data certified by manufacturer's laboratory with a current accreditation under the NVLAP for Energy Efficient Lighting Products.

b. Testing Agency Certified Data: For indicated luminaires, photometric data certified by a qualified independent testing agency. Photometric data for remaining luminaires shall be certified by manufacturer.


B. Shop Drawings: For nonstandard or custom luminaires.

1. Include plans, elevations, sections, and mounting and attachment details. 2. Include details of luminaire assemblies. Indicate dimensions, weights, loads, required

clearances, method of field assembly, components, and location and size of each field connection.

3. Include diagrams for power, signal, and control wiring.

C. Samples: For each luminaire and for each color and texture with standard factory-applied finish.

D. Samples for Initial Selection: For each type of luminaire with custom factory-applied finishes.

1. Include Samples of luminaires and accessories involving color and finish selection.

E. Samples for Verification: For each type of luminaire.

1. Include Samples of luminaires and accessories to verify finish selection. 2. Lamps, installed. 3. Cords and plugs. 4. Pendant support system.

F. Product Schedule: For luminaires and lamps.


A. Coordination Drawings: Reflected ceiling plan(s) and other details, drawn to scale, on which the following items are shown and coordinated with each other, using input from installers of the items involved:

1. Luminaires. 2. Suspended ceiling components. 3. Partitions and millwork that penetrate the ceiling or extend to within 12 inches (300 mm)

of the plane of the luminaires. 4. Structural members to which equipment will be attached. 5. Initial access modules for acoustical tile, including size and locations. 6. Items penetrating finished ceiling, including the following:

a. Other luminaires.

B. Qualification Data: For testing laboratory providing photometric data for luminaires.

C. Product Test Reports: For each luminaire, for tests performed by a qualified testing agency.

D. Sample warranty.



A. Operation and Maintenance Data: For luminaires and lighting systems to include in operation and maintenance manuals.



1. Lamps: Ten for every 100 of each type and rating installed. Furnish at least one of each type.

2. Diffusers and Lenses: One for every 100 of each type and rating installed. Furnish at least one of each type.

3. Globes and Guards: One for every 20 of each type and rating installed. Furnish at least one of each type.


A. Luminaire Photometric Data Testing Laboratory Qualifications: Luminaire manufacturer's laboratory accredited under the NVLAP for Energy Efficient Lighting Products.

B. Luminaire Photometric Data Testing Laboratory Qualifications: Provided by an independent agency, with the experience and capability to conduct the testing indicated, that is an NRTL as defined by OSHA in 29 CFR 1910.7, accredited under the NVLAP for Energy Efficient Lighting Products, and complying with the applicable IES testing standards.

C. Mockups: For interior luminaires in room or module mockups, complete with power and control connections.

1. Obtain Architect's approval of luminaires in mockups before starting installations. 2. Maintain mockups during construction in an undisturbed condition as a standard for

judging the completed Work. 3. Approval of mockups does not constitute approval of deviations from the Contract

Documents contained in mockups unless Architect specifically approves such deviations in writing.

4. Subject to compliance with requirements, approved mockups may become part of the completed Work if undisturbed at time of Substantial Completion.


A. Protect finishes of exposed surfaces by applying a strippable, temporary protective covering before shipping.


1.10 WARRANTY

A. Warranty: Manufacturer and Installer agree to repair or replace components of luminaires that fail in materials or workmanship within specified warranty period.

1. Warranty Period: Two year(s) from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 LUMINAIRE REQUIREMENTS

A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

B. NRTL Compliance: Luminaires for hazardous locations shall be listed and labeled for indicated class and division of hazard by an NRTL.

C. FM Global Compliance: Luminaires for hazardous locations shall be listed and labeled for indicated class and division of hazard by FM Global.

D. UL Compliance: Comply with UL 1598.

E. Lamp base complying with ANSI C81.61.

F. Nominal Operating Voltage: 120 V ac.

G. Recessed Luminaires: Comply with NEMA LE 4.

H. Lamp:

1. Bulb shape complying with ANSI C79.1. 2. A19 or A21 Led or compact fluorescent. 3. CRI of 100. CCT of 3000 K. 4. Dimmable from 100 percent to zero percent of maximum light output. 5. Operating at nominal voltage of 120 V.

2.2 LUMINAIRE TYPES

A. Surface ceiling mount:

1. Progress Lighting, Lithonia, Kichler 2. Ceiling mounted. 3. Two lamp. 4. Alabaster twist on glass bowl. 5. Diameter: see schedule for size, per location. 6. Existing location: over existing backbox. Field Verify.


B. Bathroom Wall Vanity: 1. Lithonia, Cooper, 2. Wall mounted. 3. Two lamp. 4. Glass Lens. 5. See schedule for lens size. 6. Existing location: over existing backbox. Field Verify.

C. Combination Fan Light: 1. Nutone, 2. Ceiling mounted. 3. One lamp. 4. Translucent White Polymeric lens 5. Aluminum reflector. 6. CFM as required for bathroom size. 7. Existing location: over existing backbox. Field Verify. 8. Enclosed fixture rated a19 or a21 led or compact fluorescent lamp.

2.3 MATERIALS

A. Metal Parts: Free of sharp edges and burrs.

B. Sheet Metal Components: Steel unless otherwise indicated. Form and support to prevent warping and sagging.

C. Doors, Frames, and Other Internal Access: Smooth operating, free of light leakage under operating conditions, and designed to permit relamping without use of tools. Designed to prevent doors, frames, lenses, diffusers, and other components from falling accidentally during relamping and when secured in operating position.

D. Lenses, Diffusers, and Globes:

1. Glass Lighting Diffusers.

E. Housings:

1. Steel Construction. 2. Painted Finish.

F. Factory-Applied Labels: Comply with UL 1598. Include recommended lamps. Locate labels where they will be readily visible to service personnel, but not seen from normal viewing angles when lamps are in place.

1. Labels shall include the following lamp characteristics:

a. "USE ONLY" and include specific lamp type. b. Lamp diameter, shape, size, wattage, and coating. c. CCT and CRI for all luminaires.


2.4 METAL FINISHES

A. Variations in finishes are unacceptable in the same piece. Variations in finishes of adjoining components are acceptable if they are within the range of approved Samples and if they can be and are assembled or installed to minimize contrast.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work.

B. Examine roughing-in for luminaire to verify actual locations of luminaire and electrical connections before luminaire installation.


3.2 TEMPORARY LIGHTING

A. If approved by the Architect, use permanent luminaires for temporary lighting. Install and energize the minimum number of luminaires necessary. When construction is sufficiently complete, remove the temporary luminaires; disassemble, clean, and install new lamps; and reinstall luminaires.

3.3 INSTALLATION

A. Comply with NECA 1.

B. Install luminaires level, plumb, and square with ceilings and walls unless otherwise indicated.

C. Install lamps in each luminaire.

D. Supports:

1. Sized and rated for luminaire weight. 2. Able to maintain luminaire position after cleaning and relamping. 3. Provide support for luminaire without causing deflection of ceiling or wall. 4. Luminaire mounting devices shall be capable of supporting a horizontal force of 100

percent of luminaire weight and vertical force of 400 percent of luminaire weight.

E. Wall-Mounted Lighting Luminaire Support: 1. Install at existing locations.



A. Perform the following tests and inspections:

1. Operational Test: After installing luminaires, switches, and accessories, and after electrical circuitry has been energized, test units to confirm proper operation.

2. Test for Emergency Lighting: Interrupt power supply to demonstrate proper operation. Verify transfer from normal power to battery power and retransfer to normal.

B. Luminaire will be considered defective if it does not pass operation tests and inspections.

C. Prepare test and inspection reports.

3.5 STARTUP SERVICE

A. Perform startup service.

3.6 ADJUSTING

A. Occupancy Adjustments: When requested within 12 months of date of Substantial Completion, provide on-site assistance in adjusting the direction of aim of luminaires to suit occupied conditions. Make up to two visits to Project during other-than-normal hours for this purpose. Some of this work may be required during hours of darkness.

1. During adjustment visits, inspect all luminaires. Replace lamps or luminaires that are defective.

2. Parts and supplies shall be manufacturer's authorized replacement parts and supplies. 3. Adjust the aim of luminaires in the presence of the Architect.



SECTION 26 2726 - WIRING DEVICES

PART 1 - GENERAL



1.2 SUMMARY


1. Straight-blade convenience, tamper-resistant receptacles. 2. GFCI receptacles. 3. Toggle switches. 4. Residential devices. 5. Wall plates.

1.3 DEFINITIONS

A. Abbreviations of Manufacturers' Names:


B. EMI: Electromagnetic interference.

C. GFCI: Ground-fault circuit interrupter.

D. Pigtail: Short lead used to connect a device to a branch-circuit conductor.



B. Shop Drawings: List of legends and description of materials and process used for premarking wall plates.

C. Samples: One for each type of device and wall plate specified, in each color specified.



A. Field quality-control reports.


A. Operation and Maintenance Data: For wiring devices to include in all manufacturers' packing-label warnings and instruction manuals that include labeling conditions.



PART 2 - PRODUCTS

2.1 GENERAL WIRING-DEVICE REQUIREMENTS

A. Wiring Devices, Components, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.


C. Devices that are manufactured for use with modular plug-in connectors may be substituted under the following conditions:

1. Connectors shall comply with UL 2459 and shall be made with stranding building wire. 2. Devices shall comply with the requirements in this Section.

D. Devices for Owner-Furnished Equipment:

1. Receptacles: Match plug configurations. 2. Cord and Plug Sets: Match equipment requirements.

E. Source Limitations: Obtain each type of wiring device and associated wall plate from single source from single manufacturer.

2.2 STRAIGHT-BLADE RECEPTACLES

A. Duplex Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.

1. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc. 2. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems.


3. Leviton: Leviton Mfg. Company, Inc. 4. Pass & Seymour: Pass& Seymour/Legrand.

B. Tamper-Resistant Convenience Receptacles: 125 V, 20 A; comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.

1. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc. 2. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems. 3. Leviton: Leviton Mfg. Company, Inc. 4. Pass & Seymour: Pass& Seymour/Legrand. 5. Description: Labeled and complying with NFPA 70, "Health Care Facilities" Article,

"Pediatric Locations" Section.


A. General Description:

1. 125 V, 20 A, straight blade, feed-through type. 2. Comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, UL 943 Class A, and

FS W-C-596. 3. Include indicator light that shows when the GFCI has malfunctioned and no longer provides

proper GFCI protection.

B. Duplex GFCI Convenience Receptacles:


C. Tamper-Resistant, Duplex GFCI Convenience Receptacles:

1. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc. 2. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems. 3. Leviton: Leviton Mfg. Company, Inc. 4. Pass & Seymour: Pass& Seymour/Legrand

2.4 TOGGLE SWITCHES

A. Comply with NEMA WD 1, UL 20, and FS W-S-896.

B. Switches, 120/277 V, 20 A:

1. Single Pole, three way, four way:

a. Cooper: Cooper Wiring Devices; Division of Cooper Industries, Inc.


b. Hubbell: Hubbell Incorporated: Wiring Devices-Kellems.

c. Leviton: Leviton Mfg. Company, Inc.

d. Pass & Seymour: Pass& Seymour/Legrand.

2.5 RESIDENTIAL DEVICES

A. Telephone Outlet: 1. Description: Single RJ-45 jack for terminating Cabling. 2. Comply with UL 1863.

B. Combination TV and Telephone Outlet: 1. Description: Single RJ-45 jack for terminating, twisted pair cable complying with

Section 260523 "Control-Voltage Electrical Power Cables" and a single BNC connector for terminating coaxial cable.

2. Comply with UL 1863.

2.6 WALL-BOX DIMMERS

A. Dimmer Switches: Modular, full-wave, solid-state units with integral, quiet on-off switches, with audible frequency and EMI/RFI suppression filters.

B. Control: Continuously adjustable slider; with single-pole or three-way switching. Comply with UL 1472.

C. Incandescent Lamp Dimmers: 120 V; control shall follow square-law dimming curve. On-off switch positions shall bypass dimmer module.

1. 600 W; dimmers shall require no derating when ganged with other devices.

D. Fluorescent Lamp Dimmer Switches: Modular; compatible with dimmer ballasts; trim potentiometer to adjust low-end dimming; dimmer-ballast combination capable of consistent dimming with low end not greater than 20 percent of full brightness.

E. LED Lamp Dimmer Switches: Modular; compatible with LED lamps; trim potentiometer to adjust low-end dimming; capable of consistent dimming with low end not greater than 20 percent of full brightness.

2.7 WALL PLATES

A. Single and combination types shall match corresponding wiring devices.

1. Plate-Securing Screws: Metal with head color to match plate finish. 2. Material for Finished Spaces: Smooth, high-impact thermoplastic. 3. Material for Unfinished Spaces: Smooth, high-impact thermoplastic.


4. Material for Damp Locations: Thermoplastic with spring-loaded lift cover, and listed and labeled for use in wet and damp locations.

B. Wet-Location, Weatherproof Cover Plates: NEMA 250, complying with Type 3R, weather-resistant thermoplastic with lockable cover.

2.8 FINISHES

A. Device Color:

1. Wiring Devices Connected to Normal Power System: Ivory unless otherwise indicated or required by NFPA 70 or device listing.

B. Wall Plate Color: For plastic covers, match device color.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Comply with NECA 1, including mounting heights listed in that standard, unless otherwise indicated.

B. Coordination with Other Trades:

1. Protect installed devices and their boxes. Do not place wall finish materials over device boxes and do not cut holes for boxes with routers that are guided by riding against outside of boxes.

2. Keep outlet boxes free of plaster, drywall joint compound, mortar, cement, concrete, dust, paint, and other material that may contaminate the raceway system, conductors, and cables.

3. Install device boxes in brick or block walls so that the cover plate does not cross a joint unless the joint is troweled flush with the face of the wall.

4. Install wiring devices after all wall preparation, including painting, is complete.

C. Conductors:

1. Do not strip insulation from conductors until right before they are spliced or terminated on devices.

2. Strip insulation evenly around the conductor using tools designed for the purpose. Avoid scoring or nicking of solid wire or cutting strands from stranded wire.

3. The length of free conductors at outlets for devices shall meet provisions of NFPA 70, Article 300, without pigtails.

4. Existing Conductors:

a. Cut back and pigtail, or replace all damaged conductors. b. Straighten conductors that remain and remove corrosion and foreign matter.


c. Pigtailing existing conductors is permitted, provided the outlet box is large enough.

D. Device Installation:

1. Replace devices that have been in temporary use during construction and that were installed before building finishing operations were complete.

2. Keep each wiring device in its package or otherwise protected until it is time to connect conductors.

3. Do not remove surface protection, such as plastic film and smudge covers, until the last possible moment.

4. Connect devices to branch circuits using pigtails that are not less than 6 inches (152 mm) in length.

5. When there is a choice, use side wiring with binding-head screw terminals. Wrap solid conductor tightly clockwise, two-thirds to three-fourths of the way around terminal screw.

6. Use a torque screwdriver when a torque is recommended or required by manufacturer. 7. When conductors larger than No. 12 AWG are installed on 15- or 20-A circuits, splice

No. 12 AWG pigtails for device connections. 8. Tighten unused terminal screws on the device. 9. When mounting into metal boxes, remove the fiber or plastic washers used to hold device-

mounting screws in yokes, allowing metal-to-metal contact.

E. Receptacle Orientation:

1. Install ground pin of vertically mounted receptacles up, and on horizontally mounted receptacles to the left.

2. Install hospital-grade receptacles in patient-care areas with the ground pin or neutral blade at the top.

F. Device Plates: Do not use oversized or extra-deep plates. Repair wall finishes and remount outlet boxes when standard device plates do not fit flush or do not cover rough wall opening.

G. Dimmers:

1. Install dimmers within terms of their listing. 2. Verify that dimmers used for fan-speed control are listed for that application. 3. Install unshared neutral conductors on line and load side of dimmers according to

manufacturers' device listing conditions in the written instructions.

H. Arrangement of Devices: Unless otherwise indicated, mount flush, with long dimension vertical and with grounding terminal of receptacles on top. Group adjacent switches under single, multigang wall plates.


A. Install non-feed-through-type GFCI receptacles where protection of downstream receptacles is not required.



A. Test Instruments: Use instruments that comply with UL 1436.

B. Test Instrument for Convenience Receptacles: Digital wiring analyzer with digital readout or illuminated digital-display indicators of measurement.

C. Perform the following tests and: 1. Test Instruments: Use instruments that comply with UL 1436. 2. Test Instrument for Convenience Receptacles: Digital wiring analyzer with digital readout

or illuminated digital-display indicators of measurement.

D. Tests for Convenience Receptacles:

1. Line Voltage: Acceptable range is 105 to 132 V. 2. Percent Voltage Drop under 15-A Load: A value of 6 percent or higher is unacceptable. 3. Ground Impedance: Values of up to 2 ohms are acceptable. 4. GFCI Trip: Test for tripping values specified in UL 1436 and UL 943. 5. Using the test plug, verify that the device and its outlet box are securely mounted. 6. Tests shall be diagnostic, indicating damaged conductors, high resistance at the circuit

breaker, poor connections, inadequate fault current path, defective devices, or similar problems. Correct circuit conditions, remove malfunctioning units and replace with new ones, and retest as specified above.

E. Test straight-blade for the retention force of the grounding blade according to NFPA 99. Retention force shall be not less than 4 oz. (115 g).

F. Wiring device will be considered defective if it does not pass tests and inspections.

G. Prepare test and inspection reports.
