SCHEDULE-I ELECTRONICS MECHANIC TRADE

NIT NO.-03/2014-15 of IMC TUFANGANJ MEMBER SECRETARY, IMC SOCIETY, ITI TUFANGANJ

TRADE: electronics mechanic under cts as per revised syllabus W.E.F. 2014

LIST OF TOOLS & EQUIPMENTS FOR 20 TRAINEES + 1

B. General Machinery Shop outfit

Sl.

No

Description of Training Material small

Tools, Equipments & Consumable goods

Make &

Model

Required

Quantity

.

#Rate

Per Unit

(in Rs.)

**Tax amount

(VAT/ Cess/

Duties etc. If

any) In Rs.

Rate per unit

including VAT/

Cess/ Duties etc.

(Col-4+ Col-5)

Total

(In Rs.), ( word & figure), (Col-3 x

Col-6)

Remarks

(% of VAT)

1 2 2A 3 4 5 6 7 8

1 Function generator (Triangular, square and sine wave),6-Digit LED display,30MHz frequency counters Int. /Ext.,Attenuators: -20dB,-40dB,-60dB and -20dB variable Output Frequency : 0.2Hz-2MHz Out Put Waveform: Sine, Square, Triangle, Ramp pulse Etc. Output Impedance : 50Ω +/- 10% Symmetry : 10% - 90% Frequency Range : 0.5Hz – 30MHz Sensitivity : 200mVrms Accuracy : 0.1Hz/1Hz Maximum Input Voltage: 50Vpp Power Source : 200-240VAC, Accuracy : +/- 10%, Frequency : 50Hz +/- 2Hz

2 Electronics Work Bench fitted with Dual DC regulated power supply 30-0-30 V, 2 Amps - 2 Nos.

Output Voltage: 0-30V AC Output Current : 0-2 Amp Input Voltage : 230V ±10%, Power Required : 1Phase (230V AC), Frequency : 50Hz The output voltage & current can be independently set at the desired level with a course and a fine control. Continuous reading of output voltage and current is done by two meters. DC regulated variable power supply 0-24 V, 1Amp-1 No. Green LED Display Auto-tracking on PARALLEL and SERIAL working condition Presetting the voltage and current DC Output Switch Input : 220 / 110V ±10% 50~60Hz Variable Output Voltage : 0 - 24V DC Variable Output Current : 0 - 1A CRO Dual Trace 20 MHz - 1No., Y deflection operation: Y1, Y2, ALT, CHOP, ADD, mode X-Y Vertical Deflection: 5mV/Div to 20V/Div in factor 1-2-5 sequence in 12 steps, Rising time: < 18nS Maximum Input Voltage: 400V (DC +ACp-p), Sweep time factor: 0.1uS/div to 0.2s/div in 1-2-5 sequence in 20 steps Magnification: x10 X-Y Mode input: X-Axis YI and Y-Axis Y2 Z Axis minimum input level: TTL Level Calibration Signal: Square wave of 0.5V at 1kHz CTR Display size: 8cm x 10cm

31. Battery Charger-1 No. Dry and Lead Acid Batteries Model 10 A. 6/12/18/24Volt. 34. Dimmer start 3 Amps. -1 No. Portable Type Current : 3Amp, Input Voltage: 230V

AC, Frequency: 50Hz

3 Rheostats various values and ratings (0-50 ohm & 0-300 ohm )

4 Assembled computer with G31 Mother Board, Dual Core processor, 160 GB HDD, 1 GB DDR-II RAM, 14" TFT Monitor, Keyboard, Mouse, Cabinet with SMPS, DVD R/W, Bluray Drive & Player, MS office education version & LAN Card

5 Laptop, 14" LED, Processor Core-i3, RAM 4GB,DDR III, 500 GB HDD, Preloaded paper license O/S windows 8

6 ELECTRONICS CIRCUIT SIMULATION SOFTWARE (Six User License) The features includes: · Highly intuitive graphic user interface · Versatile circuit node naming · Automatic point-to-point wiring · Wire connectivity maintained during moves · Automatic Bill of Materials generation · PCBnetlist export · Snap grid with device "nudging" using arrow keys · Device rotation in 90 degree

increments · Rotate, Mirror and Repeat placement · Undo, Redo, Duplicate and Merge circuits · Zoom in or out 10%-1000% · Wide range of user-definable colors · Fully stylized multi-line text · Alphanumeric pin designations; barred pins; vertical or · horizontal pin orientation · Fit-circuit-to-window feature · User-sizable connection area for wires · Multiple wires to the same device pin · Cut and extend wires · Context-sensitive on-line Help · Right-click pop up menus for quick access to editing tools and features. Supplies, Sources: Battery, Voltage Terminal, Signal Generator, I Source, V Source, I->I Source, V->I Source, I->Switch,V->Switch, I->V Source, V->V Source Math devices: A wide variety of devices for manipulating quantities Miscellaneous Devices: Crystals, Fuses, Transformers, DC Motor, F-V & V-F converters Transmission lines: Lossles, Lossy, and Uniform Distributed RC Vacuum Tubes: 12AU7, 12AX7, 5879, 6L6GC, 6SN7, 7199P, 7199T Instruments: Oscilloscope, Digital

Multimeter, Bode Plotter, Curve Tracer, Data Sequencer, Signal Generator, Logic Analyzer, Logic Probe, Logic Pulser Simulation Controls: Initial Condition and Nodeset devices Miscellaneous: Optoisolators, Photodiodes, Regulators, References, SCRs, Triacs

7 DSO ( color) Channels:2CH+1EXT Memory Depth: 32kpts Color TFT-LCD Display, 480*234 500MSa/Sec Sampling Rate Math Operation: +,-,*,/,FFT 25MHz Bandwidth 6 digits hardware Frequency Counter, real time counting display Support SCPI programming command control Interface: USB Device ,USB Host, RS-232, Pass/Fail Unique digital filter and data recorder function Embedded 12 languages, online help, one key storing and one key printing Vertical Sensitivity: 2mV ~ 10V/Div 8 Bit Vertical Resolution Trigger Source: CH1,CH2,Ext,Ext/5,AC Line Trigger Type: Edge, Pulse, Video, Slope, Alternative

8 SMD Soldering & De soldering Station with necessary Accessories Input voltage 170 to 270 V Temperature range 180 to 270 V

Temperature stability ±10°C Temperature accuracy ±1°C of tolerance at idling time Tip to ground potential under 2mV Tip to ground resistance under 2 Ohms Desoldering : De-sold 70 watts Input 170 to 270V (190 to 290V AC) Temperature range 180 to 480°C Pump diaphragm type Vacuum 600 mm/Hg For SMD Rework Air pump diaphragm pump Capacity 24L/min Hot air temperature 200 to 550°C Temperature accuracy ±1°C Accurate and advanced temperature Control with micro controller technology.Set / Read of temperature Increase and Decrease of keys to set temperature once set the read temperature will display after two seconds by default. Temperature control accuracy ±1°C. Last set value of temperature is stored in memory Burn proof silicon cable with thermal resistance up to 600°C

9 ELECTRICAL TRAINER FITTED WITH RESOURCES MENTIONED AT Sl No ( DOL starter, contactors, relays, MCB, Motor suitable for electrical control circuit exercises) Technical Specifications:- Aluminum profile sturdy flat panel (table top) system, carrying various high voltage components housed in

plastic enclosures (panel) to minimize shock possibility. Input 3 phase DOL Starter panel (EMT1). 4 pole MCB of 415 V/4A. DOL 9A Contactor with 230V / 50Hz / 11VA Coil. Bimetallic thermal O/L relay with range 1.4A - 2.3A. Consist of 2 nos of (96x96mm) Digital meters one each for. 3 ph. & 1 ph. Measures V, I, PF (0.2 lag unity 0.2 lead), Hz. Current specs for 3 ph. meter = 5A (Balanced load) and 1A/5A for 1ph. meter (170-250V) FWD/REV, 3 pole 3 way switch with center OFF, 6A/440V

10 Frequency modulator and Demodulator trainer kit FEATURES:- 01. ± 12V D.C. at 100 mA, IC Regulated Power Supply. 02. Carrier generator circuit which generates the carrier signal. 03. Audio frequency modulating signal. 04. Variable D.C. is provided to see the frequency deviation in carrier frequency. 05. Frequency Modulation circuit with buffer stage at the output. 06. Demodulating circuit. 07. Adequate no. of other electronic components. 08. Mains ON/OFF switch, Fuse and Jewel light.

* The unit is operative on 230V ±10% at 50Hz A.C. Mains.

11 PAM, PPM,PWM Trainer Kit PAM Trainer Kit ±9V D.C. at 100mA, IC regulated Power Supply internally connected. Variable frequency sampling pulse generator. Sine wave audio frequency modulating signal generator.PAM Modulator circuit based on an operational amplifier. PPM Trainer Kit Adequate no. of patch cords stackable from rear both ends 2mm spring loaded plug length ½ meters. Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections/observation of waveforms. Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References. ± 6V D.C. at 100mA, PWM Trainer Kit The unit is operative on 230V ±10% at 50Hz A.C. Mains. Adequate no. of patch cords stackable from rear both ends 2mm spring loaded plug length ½ meters. Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections/observation of waveforms. Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design

procedures, Report Suggestions and Book References. ± 6V D.C. at 100mA,

12 Microcontroller kits (8051) along with programming software (Assembly level Programming) One socket is provided for RAM expansion up to 64k. 16K bytes of powerful monitor EPROM using 27512. 48 I/O lines using 2 Nos. of 8255 brought at 26 Pins FRC Connector to interface with IC-XX Series. Three Channel Timer/ Counter using 8253 brought out at 10 Pins FRC Connector. 25 Keys Hexadecimal Keyboard and Six Digit Seven segment display using 8279 KBD Controller. Two External interrupts INT0 & INT1 are available at 40 pin FRC connector. RS-232C interface using 8251 brought out at 9 Pins D-Type Connector. Auxiliary RS-232C using RX/TX of 8051 brought out at 9 Pins D-Type Connector. Two modes of operation: - Keyboard Mode. & Serial Mode. Powerful Commands like Examine/ Edit Memory, Examine/Edit Register, Single stepping, Execution, Break Point can be used through hex Keyboard or PC serial mode. Facility for Downloading/Uploading files from/to PC. All Address, Data, Control & Port lines are available on 40 Pins & 20 Pins FRC Connector.

13 Application kits for Microcontrollers 6

different applications SPECIFICATIONS * CPU: 8031 Micro Controller 12MHz. * MEMORY: 32KB EPROM, 32 KB RAM and 2KB NV RAM. Battery Backup for RAM. * PERIPHERALS: 8279 for controlling 24 feather keys (including 6 digit seven segment display). : 32 programmable I/O pins (24 from 8255 and 8 from port 2 of 8031). * POWER SUPPLY: ±5V @ 500mA. All assembled in a well designed cabinet. * ACCESSORIES : 50 pin FRC Cable 1 No.

14 Sensor trainer kit (containing Various sensors like Thermocouple, RTD, Thermocouple, load cell, strain gauge, LVDT, smoke sensors, speed sensor )

15 SMPS of different make

16 UPS 3 KVA with backup time minimum 30 minutes Output Power Capacity : 2250 Watts / 3000 VA Max Configurable Power : 2250 Watts / 3000 VA Nominal Output Voltage : 230V Output Voltage Note : Configurable for 220 : 230 or 240 nominal output voltage Output Voltage Distortion : Less than 5% at full load Output Frequency (sync to mains): 57 - 63 Hz for 60 Hz nominal, 47 - 53 Hz for 50 Hz nominal

NOTE:- FOR QUANTITY YOU CAN SEE THE SYLLABUS IN OUR WEBSITE IN THE TRADE INFORMATION TAB AT LEFT

Crest Factor : up to 5 : 1 Topology : Line Interactive Waveform Type : Sine wave Output Connections : (8) IEC 320 C13 Nominal Input Voltage : 230V Input Frequency : 50/60 Hz +/- 3 Hz (auto sensing) Input Connections: Hard Wire 3-wire Input voltage range for main operations : 176 - 282V including Battery

17 Mobile phone (different models) at least one 3G Mobile, 1 No CDMA, 1 No. 2G (GSM) & 1 No. 3G (GSM)

18 Smart Phones of different make (Android/ Windows)- 4 No

19 Tweezers – Bend tip

20 Cell phone power source with charger chords for different cell phones

21 LCD TV (21")

22 LED TV (21")

23 Home Theatre System

24 Solar Power Inverter, 500 VA

25 LED lighting system, Preferably running display type.