samsung shark user guide

10
Simplified operation instructions for Samsung Shs-2320 “Shark(this manual is unofficial and translated version only) Registering Pin Number Perform this operation during door unlocked status 1. Press [Register button] (located at the battery compartment, remove cover) 2. Enter PIN number to be registered (4~12 digits) 3. Press Button Registering Card/Key tag 1. Press [Register button] 2. Place the card/key tag to be registered on the sensor 3. Press [Register button] again

Upload: costtinescu

Post on 06-May-2017

217 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Samsung Shark User Guide

Simplified operation instructions for Samsung Shs-2320 “Shark”

(this manual is unofficial and translated version only)

Registering Pin Number

Perform this operation during door unlocked status

1. Press [Register button] (located at the battery compartment, remove

cover)

2. Enter PIN number to be registered (4~12 digits)

3. Press Button

Registering Card/Key tag

1. Press [Register button]

2. Place the card/key tag to be registered on the sensor

3. Press [Register button] again

Page 2: Samsung Shark User Guide

Opening The door using Pin number (outside)

1. Place palm slightly on the [number pad]

2. When the number pad lights up, enter your Pin on the number pad

3. Press .

*Double-Security mode

1. Place palm slightly on the [number pad]

2. When the number pad lights up, press the two random number that will

appear on the screen

3. Enter Pin on the number pad

4. Press button.

Opening the door (outside)Card/Keytag

1. Place palm slightly on the [number pad]

2. When the number pad lights up, place card/key tag on the sensor

Page 3: Samsung Shark User Guide

Opening/closing the door from the inside

Automatic Lock Mode

1. On the main body inside press [열림/닫힘] (open/close) button

and the door will be lock or unlock

Manual Lock mode

1. On the main body inside, Turn the manual switch knob to open or

close, exposing green color indicates open status while red color

indicates closed status

Double/Normal Security mode setting

1.Press [register button] inside

2.Press [7] to set Double security Mode on the number pad or

3.Press [9] to set Normal lock mode on the number pad

4.Press button

Page 4: Samsung Shark User Guide

Setting Authentication Sensor

1.Press [register button] inside

2.Press [1] to enable Authentication Sensor on the number pad or

3.Press [3] to disable Authentication Sensor on the number pad

4.Press button

Setting Double authentication mode

1.Press [register button] inside

2.Press [4] to enable Double Authentication mode on the number pad or

3.Press [6] to disable Double Authentication mode on the number pad

4.Press button

Setting Automatic Lock/Mabual lock Mode

1. On the main body inside switch automatic/manual lock mode

By switching switch

Adjusting Volume (Setting Sound)

1. On the main body inside, adjust sound by the following setting

[1] Mute [2] Normal [3] Loud

Page 5: Samsung Shark User Guide

Cancelling Alarms

Invalid entry alarm – (in case of multiple wrong password/card/key tag

entry)

1. On the main body press [register] button or [open/close] button

2. Outside, press Pin followed by on the number pad, or place

card/key tag on the sensor

Intrusion alarm (outside)

1. On the main body press [register] button or remove one battery

2. Outside, press Pin followed by on the number pad, or place

card/key tag on the sensor

Page 6: Samsung Shark User Guide

How to use Emergency Battery

1. Using a 9V battery, make a contact by placing the 9V battery in an

upward position connecting the polarity with the terminal node.

2. In this status you can now enter your Pin number, or place key tag/card

To initialize the unit (refer to the illustrations)

Battery replacement

*Average Battery Lifetime

1.5V alkaline AA x 4 (ave. 10 operations per day) 1 year

Please use alkaline battery only Replace Battery notification

The battery icon will be lighted red and an alarm will go off signaling the

need to replace battery.

Page 7: Samsung Shark User Guide

Please change the battery at this time

*please observe correct polarity placement when changing battery

*please check battery for damage and leaks before changing

*replace battery all at once, do not replace with used or mix new with old

used ones. (Refer illustrations below)

On the main body press the Battery cover release button, lift the cover up

And replace the battery in this manner.

Page 8: Samsung Shark User Guide

Trouble Shooting

No power

-check battery, if inserted correctly or check if in good condition Registration problem

(PIN)

-When registering please make sure to register pin within the 10 seconds

time frame, when registration failed, try registering again.

-check battery power if sufficient (CARD/KEYTAG)

When registering card/keytag please make sure to register pin within the

10 seconds time frame, when registration failed, try registering again Door not unlocking

Even after entering password and pressing [*] button

-Make sure the password is registered first before trying to use.

-Enter password when the number pad is lighted

(slightly touch number pad first ,when activated, enter pin number) Even after using Card/key tag to open door

-Make sure the Card/key tag is registered first before trying to use

-You should place the Card/key tag on the sensor correctly If double-lock feature is activated, you cannot open the door by

password or key tag or card only

When double-lock feature is enabled, you have to place palm slightly on

the number pad first to activate, wait for the (bee~ree~reep sound) and

then you can place card or key tag on the sensor to unlock the door.

for instance the unit is not responding despite standard procedure

is done, the unit may be defective and you should contact service

center.

Page 9: Samsung Shark User Guide

Auto-relock function not working

- make sure you have set the unit to automatic lock mode

- when set to manual mode, after closing the door, touch slightly the

number pad, to initialize relock.

*this event can also happen if the unit is installed incorrectly,

for instances like these, please contact service center.

* If the battery is completely discharged, the automatic lock feature does

not work, please check power supply if sufficient.

Number Pad is not activating

-on the front body outside, beside the Power on/off button, press the

“reset” button with a pin.

*after standard procedure is done, but unit still not responding,

contact service center

Operation summary

Pin registration/modify

1. Register button + enter pin + button Card/Keytag registration

1. Register button + place card/keytag on the sensor + register

button again

Opening door from inside

1. (Automatic) in locked status, press +open door

2. (Manual) turn manual lock knob to unlock position + open door

Closing door from inside

1. (Automatic) press and the door will be locked

2. (Manual) turn manual lock knob to lock position and door will be locked

Page 10: Samsung Shark User Guide

Opening the door from the outside

Double security mode

Card/key tag – touch number pad + place card/key tag on the sensor.

Pin - touch number pad + press the 2 random number that will appear +

enter Pin number + button

Closing the door from the outside

Automatic Lock – after closing the door, the automatic lock will activate

Manual Lock – touch number pad slightly, and the door will be locked

Setting double security mode

On Safe mode – register button + 7 +

On normal mode - register button + 9 +

How to enable/disable double authentication mode

Enable - register button + 4 +

Disable - register button + 6 +

Setting Automatic/Manual Lock mode

Automatic- [자동/수동잠김] switch to “automatic”

Manual - [자동/수동잠김] switch to “manual”

Setting Sound volume

Adjust volume setting from low, normal &

loud

Enable/disable Authentication Sensor

Enable - register button + 1 +

Disable - register button + 3 +

Setting anti-hack feature

Enable- after closing the door, press button

Disable-enter password, or place key tag/card on sensor.

Turn-off alarm(inside)

Press register button

Turn-off alarm(outside)

Enter Pin or place card/key tag on the

sensor