sabre platform
TRANSCRIPT
-
8/11/2019 Sabre Platform
1/6
Standard Template ConstructSer. 49871124
Security clearance Magenta
Agripinaa patternSabre gun platform
Thought for the day:through hard work shall we conquer
-
8/11/2019 Sabre Platform
2/6
Agripinaa pattern
Sabre gun platform
The sabre gun platform is an STCweapons system designed for
defence and static emplacement inthe Anti air role. It can howeverbe effectively deployed againstground targets.
The platform can be fitted with arange of weapons including:
-Heavy Stubbers pair and quad.
-Heavy Bolters
-Autocannon
Sabre platforms are manufacturedon several major and minor Forgeworlds.
Variants to the design can beobserved and are attributable toredistribution and conservative
use of resources.
Sabre platforms are distributedwidely in Guard, Naval groundforces and Planetary Defence
Force units.
Intensive training is requiredwhen the system is deployed inthe AA role if munitions
expenditure is to be effectivelymanaged
-
8/11/2019 Sabre Platform
3/6
Agripinaa pattern
Sabre gun platform
STC instructions
In order to supply an army
with Sabre platforms the
Fabricator will need to
requisition the following
Components from stores;
-40mm figure base
-Embossed plasticard- Latticeor Tread plate
-A length of sprue at least
100/120mm
-A length plastic tube or rod
2mm Dia.
-A City of Death Lamp Post
-Baneblade smoke dispenser
mounting.
-A choice of weapon;
Heavy Bolter- from the SOB
immolator kit ( a great
source of Bits! Especially
if all you want is a
standard Rhino- the extra
cost is worth it)
Heavy Stubbers- From the
Shadowsword/Stormlord kit.-A selection of plastic rod.
-Sights from the Ork boys
sprue
-Cadian/Catachan heavy weapon
arms ( for the bolter etc)
And of course legs, torso and
head for the crewman.
.
-
8/11/2019 Sabre Platform
4/6
Fabrication Stage 1: The Base
Drill a hole through the centreof the 40mm base. The hole wants
to be of a size to accommodatethe plastic rod that thefabricator is using. Brass rod
or tube may be used which willgive a stronger joint.
Glue the 40mm base to theembossed plasticard and allow itto dry (overnight ideally) .
Cut round the base and sand to
ensure a nice even disc. Drillthrough the hole created earlierand through the plasticard.
Stage 2.
Cut the sprue into roughly 30mmlong lengths and then cut the
ends at an angle like so.
Stage 3.
Glue the legs to the base. Inorder to ensure that the legs
are evenly spaced round the base
form an equilateral trianglearound the hole that has beendrilled in the middle as shownin image 3. At this stage if thefabricator has the resources
pads may be added to the legs.Plasticard of an appropriatethickness and a hole punch willachieve the required effect.
Agripinaa pattern
Sabre gun platform
STC instructions
-
8/11/2019 Sabre Platform
5/6
Agripinaa pattern
Sabre gun platform
STC instructions
Fabrication Stage 4: The Gun
support
The fabricator should cut the
base off the lamp post ensuring
a straight clean cut.
A further cut in the location
shown on image 4 is required in
order for the gun support post
be the correct height.
Drill the bottom of the post to
accept a length of plastic rod
or tube ensuring that it is long
enough to pass through the top
and bottom of the base.
Stage 5.
Once dry (again overnight
ideally) it may be installed to
the base. If the fabricator
wishes the gun mount to rotate
the post should not be glued.
Stage 6.The smoke grenade discharger
support from the Baneblade or
Shadowsword is added to the top
of the post. This will support
the gun mount.
-
8/11/2019 Sabre Platform
6/6
Agripinaa pattern
Sabre gun platform
STC instructions
Fabrication Stage 7: The Gun
mount
The example shown here is for
the heavy bolter.
2 lengths of plastic rod were
cut and glued into place. One inthe holes in the bolters (where
they join the Turret of the
immolator). The other, of a
smaller diameter to the rear.
The heavy weapons arms will
attach to this.
Stage 8.
Add a length of T- bar level
with the ammo hoppers and addone of the Ork sights or
something similar.
An Auspex could be used towards
the rear of the gun if a more
sophisticated sighting system
was called for.
Stage 9.
Glue the guns to the support
post and the crewman to the
guns.
Success Fabricator! Now return
to your stores and start a
production line. Additional
detail may be added to taste.
Notably the Ork sprues provide
empty cases both as they are
ejected from the gun or in apile on the floor.