s1d13517 display controller s5u13517p00c100 … sheets/epson pdfs...s1d13517 display controller...
TRANSCRIPT
S1D13517 Display Controller
S5U13517P00C100 Evaluation Board User
Manual
SEIKO EPSON CORPORATION Rev. 1.0
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia-bility of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or cir-cuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of International Trade and Industry or other approval from another government agency.
All other product names mentioned herein are trademarks and/or registered trademarks of their respective companies.
©SEIKO EPSON CORPORATION 2009, All rights reserved.
S1D13517 Display Controller
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Chapter 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Chapter 3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.1.2 Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.1.3 S1D13517 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.4 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4.1 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . . . . . 134.4.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . . . . 14
4.5 LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154.6 GPO and PWM Connections . . . . . . . . . . . . . . . . . . . . . . . . 16
Chapter 5 Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 6 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Chapter 7 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Chapter 8 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 3
S1D13517 Display Controller
4 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
Chapter 1 IntroductionThis manual describes the setup and operation of the S5U13517P00C100 Evaluation Board. The evaluation board is designed as an evaluation platform for the S1D13517 Display Controller.
The S5U13517P00C100 evaluation board can be used with many native platforms via the host connector which provides the appropriate signals to support a variety of CPUs. The S5U13517P00C100 evaluation board can also connect to the S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0.
This user manual is updated as appropriate. Please check the Epson Research and Development Website at www.erd.epson.com for the latest revision of this document before beginning any development.
We appreciate your comments on our documentation. Please contact us via email at [email protected].
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 5
S1D13517 Display Controller
Chapter 2 FeaturesThe S5U13517P00C100 Evaluation Board includes the following features:
• S1D13517 Display Controller (128-pin QFP)
• Integrated Silicon Solution, Inc. IS42S16800E-7TLI 128M-bit SDRAM (54-pin TSOP)
• Header with all S1D13517 Host Bus Interface signals
• Headers for connection to the S5U13U00P00C100 USB Adapter board
• Headers for connecting to LCD panels
• Header for S1D13517 GPO pins and PWM pin
• On-board 24MHz oscillator
• 14-pin DIP socket (if a clock other than 24MHz must be used)
• 3.3V input power
• On-board voltage regulator with 2.5V output
• On-board voltage regulator with adjustable 6~24V output, 40mA max., to provide power for LED backlight of LCD panels.
6 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
Chapter 3 Installation and ConfigurationThe S5U13517P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it to be used with a variety of different configurations.
3.1 Configuration DIP Switch
The S1D13517 has 2 configuration inputs (CNF[1:0]). A DIP switch (SW1) is used to configure CNF[1:0] as described below.
The following figure shows the location of DIP switch SW1 on the S5U13517P00C100 board.
Figure 3-1: Configuration DIP Switch (SW1) Location
Table 3-1: Summary of Power-On/Reset Options
SDU13517P00C100 SW1-[2:1] Config
S1D13517 CNF[1:0] Config
Power-On/Reset State1 (ON) 0 (OFF)
SW1-[1] CNF0 Host data bus is 8-bit Host data bus is 16-bit
SW1-[2] CNF1 Host interface is ALE bus Host interface is i80 bus
= Required settings when using S5U13U00P00C100 USB Adapter board
DIP SwitchSW1
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 7
S1D13517 Display Controller
3.2 Configuration Jumpers
The S5U13517P00C100 has 6 jumpers which configure various board settings. The jumper positions for each function are shown below.
J1, J2, J3 - Power Supplies for the S1D13517
J1, J2, J3 can be used to measure the current consumption of each S1D13517 power supply. When the jumper is at position 1-2, normal operation is selected. When no jumper is installed, the current consumption for each power supply can be measured by connecting an ammeter between pins 1 and 2 of the jumper.
The jumper associated with each power supply is as follows: J1 for COREVDD J2 for IOVDD J3 for PLLVDD
Figure 3-2: Configuration Jumper Locations (J1, J2, J3)
Jumper Function Position 1-2 Position 2-3 No Jumper
J1 COREVDD Normal — COREVDD current measurement
J2 IOVDD Normal — IOVDD current measurement
J3 PLLVDD Normal — PLLVDD current measurement
J4 IOVDD source 3.3V CN1 connector, pin 32 —J5 24MHz control 24MHz stop — Normal
= Required settings when using S5U13U00P00C100 USB Adapter board
Jumper Function Position 1-2 Position 3-4 Position 5-6J6 Clock source On board 24MHz Second oscillator CLKI pin to GND
J3
J2, J1
8 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
J4 - IOVDD Source
J4 is used to select the source for the IOVDD supply voltage. When the jumper is at position 1-2, the IOVDD voltage is provided by the 3.3V power supply of the board. When the jumper is at position 2-3, the IOVDD voltage must be provided to the CN1 connector, pin 32.
J5 - 24MHz Control
J5 is used to control the 24MHz oscillator. When no jumper is installed, the 24MHz oscillator is running. When the jumper is at position 1-2, the 24MHz oscillator is stopped.
J6 - Clock Source
J6 is used to select the source for the clock input. When the jumper is at position 1-2, the on board 24MHz oscillator is selected. When the jumper is at position 3-4, the second oscillator is selected. When the jumper is at position 5-6, the CLKI pin is forced to GND.
Figure 3-3: Configuration Jumper Location (J4, J5, J6)
J4J5
J6
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 9
S1D13517 Display Controller
Chapter 4 Technical Description
4.1 Power
4.1.1 Power Requirements
The S5U13517P00C100 evaluation board requires an external regulated power supply (3.3V / 0.5A). The power is supplied to the evaluation board through pin 34 of the CN1 header, or pin 5 of the P2 header.
The green LED ‘3.3V Power’ is turned on when 3.3V power is applied to the board.
4.1.2 Voltage Regulators
The S5U13517P00C100 evaluation board has an on-board linear regulator to provide the 2.5V power required by the S1D13517 Display Controller. It also has a step-up switching voltage regulator to generate adjustable 6~24V, which can be used to power the LED backlight on some LCD panels.
4.1.3 S1D13517 Power
The S1D13517 Display Controller requires 2.5V and 3.0~3.6V power supplies.
2.5V power for COREVDD and PLLVDD is provided by an on-board linear voltage regulator.
IOVDD can be in the range of 3.0~3.6V. When J4 is set to the 1-2 position, IOVDD is connected to 3.3V. If a different voltage is required for IOVDD, set JP4 to the 2-3 position and connect the external power supply to pin 32 of connector CN1.
10 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
4.2 Clocks
The clock for the S1D13517 Display Controller is provided by a 24MHz oscillator.
The S5U13517P00C100 evaluation board has a DIP14 footprint for an optional second oscillator, Y2. This is provided for cases requiring a different clock frequency for the S1D13517 Display Controller. To use Y2, an oscil-lator must be populated in the Y2 footprint and the J6 jumper placed at position 3-4.
4.3 Reset
The S1D13517 Display Controller on the S5U13517P00C100 evaluation board can be reset using a push-button (SW2), or via an active low reset signal from the host development platform (pin 33 on the CN1 connector).
Figure 4-1: Second oscillator and Reset switch Location (Y2, SW2)
Y2
SW2
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 11
S1D13517 Display Controller
4.4 Host Interface
4.4.1 Direct Host Bus Interface Support
All S1D13517 host interface pins are available on connector CN1 which allows the S5U13517P00C100 evaluation board to be connected to a variety of development platforms.
The following figure shows the location of host bus connector CN1. CN1 is a 0.1x0.1 inch 34-pin header (17x2).
Figure 4-2: Host Bus Connector Location (CN1)
For the pinout of connector CN1, see Chapter 6, “Schematic Diagrams” on page 18.
CN1
12 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
4.4.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board
The S5U13517P00C100 evaluation board is designed to connect to a S5U13U00P00C100 USB Adapter Board. The USB adapter board provides a simple connection to any computer via a USB 2.0 connection. The S5U13517P00C100 directly connects to the USB adapter board through connectors P1 and P2.
The USB adapter board also supplies the 3.3V power required by the S5U13517P00C100. IOVDD should be selected for 3.3V and J4 should be set to the 1-2 position.
When the S5U13517P00C100 is connected to the S5U13U00P00C100 USB Adapter board, there are 2 LEDs on S5U13517P00C100 which provide a quick visual status of the USB adapter. LED1 blinks to indicate that the USB adapter board is active. LED2 turns on to indicate that the USB has been enumerated by the PC.
The following diagram shows the location of connectors P1 and P2. P1 and P2 are 40-pin headers (20x2).
Figure 4-3: USB Adapter Connector Locations (P1 and P2)
For the pinout of connectors P1 and P2, see Chapter 6, “Schematic Diagrams” on page 18.
NoteA windows driver must be installed on the PC when the S5U13517P00C100 is used with the S5U13U00P00C100 USB Adapter Board. The S1D13xxxUSB driver is available at www.erd.epson.com.
P1
P2
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 13
S1D13517 Display Controller
4.5 LCD Panel Interface
The LCD interface signals are available on connectors CN3 and CN5.
Connector CN3 is 0.1x0.1 inch 40-pin header (20x2) and connector CN5 is 0.1x0.1 inch 10-pin header (5x2). For the pinout of connectors CN3 and CN5, see Chapter 6, “Schematic Diagrams” on page 18.
On the evaluation board there is an adjustable 6~24V, 40mA max. power supply. This voltage is provided only on connector CN3 (it is not used elsewhere on the board). It is intended for use to power the LED backlight on some LCD panels. The voltage is adjusted by the VR1 pot.
NoteFor LCD panels that use a CCFL backlight, an external power supply must be used to provide power to the inverter for the CCFL backlight. Usually, the inverter current consumption is higher than the maximum 40mA current available from the on-board voltage regulator.
The following diagram shows the location of the LCD panel connectors CN3 and CN5.
Figure 4-4: LCD Panel Connectors Location (CN3, CN5)
CN5
CN3
14 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
4.6 GPO and PWM Connections
The S1D13517 Display Controller has 4 GPO pins and PWM pin. All the GPO pins and PWM pin are routed to the CN4 connector. Connector CN4 is 0.1x0.1 inch 10-pin header (5x2).
The following figure shows the location of the GPO and PWM connector, CN4.
Figure 4-5: GPIO and PWM Connector Location (CN4)
For the pinout of connector CN4, see Chapter 6, “Schematic Diagrams” on page 18.
CN4
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 15
S1D13517 Display Controller
Chapter 5 Parts Lists
Table 5-1: Parts List
Item Quantity Reference Part1 1 CN1 A1-34PA-2.54DSA(71)
2 1 CN3 HIF3FC-40PA-2.54DSA
3 2 CN4,CN5 A1-10PA-2.54DSA(71)
4 27
C1,C3,C5,C7,C9,C11, C13,C15,C17,C19,C21, C23,C25,C27,C28,C31, C32,C34,C35,C37,C43, C45,C47,C49,C51,C53,
C55
0.1u
5 23
C2,C4,C6,C8,C10,C12, C14,C16,C18,C20,C22, C24,C26,C29,C33,C38, C44,C46,C48,C50,C52,
C54,C56
0.01u
6 1 C30 2000p
7 1 C36 100u
8 1 C40 47u 10v
9 1 C41 10p
10 1 C42 1u 50V
11 1 D1 SML-310VT
12 1 D2 SML-310DT
13 1 D3 SML-310PT
14 1 D4 MBR0530
15 2 F1,F2 ACF451832-222
16 4 J1,J2,J3,J5 WL-1-2P
17 1 J4 WL-1-3P
18 1 J6 WLW-3
19 2 L1,L2 BLM21P
20 1 L3 LQH32CN100K23L
21 3 PAD1,PAD2,PAD3 2mm diameter
22 2 P1,P2 PRPN202PAEN-RC
23 1 R1 3k 1%
24 3 R2,R3,R4 10k
16 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
25 49
R5,R6,R7,R8,R10,R11, R12,R14,R15,R21,R22, R23,R24,R25,R26,R27, R28,R29,R30,R31,R32, R33,R34,R35,R36,R37, R38,R39,R40,R41,R42, R43,R44,R45,R46,R47, R48,R49,R50,R51,R52, R53,R54,R55,R56,R57,
R58,R59,R60
0
26 1 R9 150k
27 2 R13,R17 33 1%
28 1 R16 NM
29 3 R18,R19,R20 270
30 1 R61 887k
31 1 R62 22k
32 1 R63 47k
33 6 SH1,SH2,SH3,SH4,SH5, SH6 .100 in. Jumper Shunt
34 1 SW1 CFS-0400MB
35 1 SW2 SKRKAEE010
36 10 TP1,TP2,TP3,TP4,TP5, TP6,TP7,TP8,TP9,TP10 HK-2-S
37 1 U1 S1D13517
38 1 U2 TPS76915DBVT
39 1 U3 IS42S16800E (128Mbit SDRAM)
40 1 U4 TPS61040
41 1 VR1 200k
42 1 Y1 SG-210 24MHz
43 1 Y2 XR2A-1405
Table 5-1: Parts List
Item Quantity Reference Part
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 17
S1D13517 Display Controller
Chapter 6 Schematic Diagrams
Figure 6-1: S5U13517P00C100 Schematic Diagram (1 of 3)
5 5
4 4
3 3
2 2
1 1
DD
CC
BB
AA
PDG4PDG5PDG6PDG7PDB0
PDB2PDB3
PDB1
PDB4
PDB6PDB7
PDB5
MD15
MD12
MD10
MD11
MD1
MD2
MD3
MD0
MD4
MD14
MD13
MD5
CNF2TEST1
CNF0
TEST0
PLLCHGO
SCANEN
CNF1H
ALE
GP
O1
GP
O0
PDR
7PD
R6
PDR
3
PDR
5
GP
O3
PDG
3
PDR
1
PDG
0
PDR
4
PDG
1PD
G2
PDR
0
PDR
2
MD
6
MD
7M
D8
MC
LKO
MD
9
CN
F2
CN
F0C
NF1
GP
O2
HD15
HD7
HD11
HD
1
HD5
HD14
HD6
HD3
HD10
HD12
HD
2
HD8
HD13
HD4
HD9
HD
0
MC
LKI
MA
7
MA
5
MA
0
MA
9
MA
1
MA
11
MA
8M
A10
MA
6
MA
4M
A3
MA
2
HAL
E
TES
T0
MC
LKI
MC
LKO
TES
T1
SCAN
EN
PLLC
HG
O
CO
RE
IO
PLL
2.5V
DD
IOIO
VD
D
2.5V
DD
CO
RE
PLL
IOV
DD
PVSPHS
RESET#
CLKI
PDE
MC
S#
MC
KE
MR
AS
#
MC
LKO
MC
AS
#M
DQ
M1
MW
E#
MD
QM
0
PCLK
TEPW
M
PD
B[7
:0]
PD
G[7
:0]
PD
G[7
:0]
PD
R[7
:0]
GP
O[3
:0]
HD
[15:
0]
MD
[15:
0]
MD
[15:
0]
HD
[15:
0]
MB
A0
MB
A1
HD
/C#
HW
E#
HR
E#H
CS#
MA
[11:
0]
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
S1D
1351
7
A4
13
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
S1D
1351
7
A4
13
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
S1D
1351
7
A4
13
Wed
nesd
ay, A
pril
22, 2
009
CO
RE
IO
PLL
CN
F[2:
0]O
N H
igh
OFF
Low
TES
T0
SCAN
EN
TES
T1
Wire
sho
rtest
.
J2 WL-
1-2P
J2 WL-
1-2P1 2
U1
S1D
1351
7U
1S
1D13
517
VSS 1HD3 2HD4 3HD5 4HD6 5HD7 6HD8 7HD9 8HD10 9HD11 10HD12 11HD13 12HD14 13HD15 14COREVDD 15IOVDD 16VSS 17CLKI 18TEST0 19TEST1 20CNF2 21CNF1 22CNF0 23VSS 24COREVDD 25PLLCHGO 26PLLVDD 27PLLVSS 28RESET# 29SCANEN 30IOVDD 31VSS 32
MA
333
MA
434
MA
235
MA
536
MA
137
MA
638
MA
039
MA
740
MA1
041
MA
842
MB
A143
MA
944
MB
A045
MA1
146
IOVD
D47
VSS
48M
CS#
49M
CKE
50M
RA
S#51
CO
RE
VDD
52M
CLK
I53
VSS
54M
CLK
O55
MC
AS#
56M
DQ
M1
57M
WE#
58M
DQ
M0
59M
D7
60M
D8
61M
D6
62M
D9
63IO
VDD
64
VSS65 MD566 MD1067 MD468 MD1169 MD370 MD1271 MD272 MD1373 MD174 MD1475 MD076 MD1577 COREVDD78 IOVDD79 VSS80 PDE81 PVS82 PHS83 PDB784 PDB685 PDB586 PDB487 PDB388 PDB289 PDB190 PDB091 PDG792 PDG693 PDG594 PDG495 IOVDD96
VSS
97PD
G3
98PD
G2
99PD
G1
100
PDG
010
1PD
R7
102
PDR
610
3PD
R5
104
PDR
410
5PD
R3
106
PDR
210
7PD
R1
108
PDR
010
9PC
LK11
0G
PO3
111
CO
REV
DD
112
IOV
DD
113
VSS
114
GPO
211
5G
PO1
116
GPO
011
7PW
M11
8TE
119
HD
/C#
120
HA
LE12
1H
WE
#12
2H
CS#
123
HR
E#12
4H
D0
125
HD
112
6H
D2
127
IOV
DD
128
C24
0.01
u
C24
0.01
u
R3
10k
R3
10k
C19
0.1u
C19
0.1u
C27
0.1u
C27
0.1uC
8
0.01
u
C8
0.01
u
R1
3k 1
%R
13k
1%
C2
0.01
u
C2
0.01
u
C16
0.01
u
C16
0.01
u
C11
0.1u
C11
0.1u
C26
0.01
u
C26
0.01
u
SH3
.100
in. J
umpe
r Shu
nt
SH3
.100
in. J
umpe
r Shu
nt
R6
0R6
0
C20
0.01
u
C20
0.01
u
J3 WL-
1-2P
J3 WL-
1-2P1 2
TP3
HK
-2-S
TP3
HK
-2-S
C30
2000
pC
3020
00p
J1 WL-
1-2P
J1 WL-
1-2P1 2
C9
0.1u
C9
0.1u
C18
0.01
u
C18
0.01
u
C12
0.01
u
C12
0.01
u
SH1
.100
in. J
umpe
r Shu
nt
SH1
.100
in. J
umpe
r Shu
nt
C3
0.1u
C3
0.1u
C22
0.01
u
C22
0.01
u
PAD
12m
m d
iaPA
D1
2mm
dia
C23
0.1u
C23
0.1u
L1B
LM21
PL1
BLM
21P
C28
0.1u
C28
0.1u
C6
0.01
u
C6
0.01
u
SH2
.100
in. J
umpe
r Shu
nt
SH2
.100
in. J
umpe
r Shu
nt
TP1
HK
-2-S
TP1
HK
-2-S
C7
0.1u
C7
0.1u
C14
0.01
u
C14
0.01
u
C15
0.1u
C15
0.1u
R5
0R5
0
PAD
22m
m d
iaPA
D2
2mm
dia
C4
0.01
u
C4
0.01
u
C25
0.1u
C25
0.1u
TP2
HK
-2-S
TP2
HK
-2-S
R2 10
kR
2 10k
C21
0.1u
C21
0.1u
L2B
LM21
PL2
BLM
21P
C5
0.1u
C5
0.1u
C29
0.01
u
C29
0.01
u
C10
0.01
u
C10
0.01
u
SW
1
CFS
-040
0MB
SW
1
CFS
-040
0MB
C17
0.1u
C17
0.1u
C1
0.1u
C1
0.1u
C13
0.1u
C13
0.1u
PAD
32m
m d
iaPA
D3
2mm
dia
R4
10k
R4
10k
18 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
Figure 6-2: S5U13517P00C100 Schematic Diagram (2 of 3)
5 5
4 4
3 3
2 2
1 1
DD
CC
BB
AA
INT
HR
D#
HD
15H
D13
HD
11H
D9
HD
2H
D4
HD
0
HD
6
HD
10H
D12
HD
14
HW
E#
HC
S#
HD
/C#
EN
UM
AR
ETE
DH
EA
RTB
EA
T
HD
8
HD
1
HD
5H
D7
HD
3
HW
E#H
RD
#H
D/C
#
RE
SE
T#HD
2
HD
6
HD
0
HD
4
HD
8H
D10
HD
12H
D14
HD
9
HD
1
HD
11
HD
3H
D5
HD
13H
D15
HD
7
HE
AR
TBE
AT
EN
UM
AR
ETE
D
HC
S#
TEINT
TE
RE
SE
T#
IOV
DD
3.3V
DD
3.3V
DD
IOV
DD
_IN
3.3V
DD
3.3V
DD
IOV
DD
3.3V
DD
2.5V
DD
IOV
DD
IOV
DD IO
VD
D_I
N
3.3V
DD
HD
[15:
0]
HC
S#
HW
E#H
RE
#H
D/C
#
RE
SE
T#TE
CLK
I
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
HO
ST, C
LK
A4
23
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
HO
ST, C
LK
A4
23
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
HO
ST, C
LK
A4
23
Wed
nesd
ay, A
pril
22, 2
009
GN
D
Red
Ora
nge
Gre
en
2mm
Pin
Hea
der
2.54
mm
Pin
Hea
der
POW
ER
EN
UM
HB
CLK
I sel
1-2
OnB
oard
3-4
Soc
ket
5-6
GN
D
3.3V
HO
ST I/
F
Y1
Ctrl
Sho
rt D
isab
le
RE
SET
IOVD
D S
el1-
2 3.
3V2-
3 IO
VDD
_IN In
stal
ls in
pos
ition
1-2
of J
P4,
6.
TP8
HK
-2-S
TP8
HK
-2-S
P1
PRPN
202P
AEN
-RC
P1
PRPN
202P
AEN
-RC
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
U2 TP
S76
915D
BV
T
U2 TP
S76
915D
BV
T
IN1
GN
D2
EN
#3
NC
/FB
4
VOU
T5
SH4
.100
in. J
umpe
r Shu
nt
SH4
.100
in. J
umpe
r Shu
nt
C35
0.1uC
350.
1uC
340.
1uC34
0.1u
D1
SM
L-31
0VT
D1
SM
L-31
0VT
R7
0R
70
R15
0R
150
C38
0.01
u
C38
0.01
u
R9
150k
R9
150k
SH
6
.100
in. J
umpe
r Shu
nt
SH
6
.100
in. J
umpe
r Shu
nt
R13
33 1
%R
1333
1%
SW
2S
KR
KA
EE
010
SW
2S
KR
KA
EE
010
R16
NM
R16
NM
C36
100uC
3610
0u
R18
270
R18
270
R10
0R
100
J6 WLW
-3J6 W
LW-3
123456
C31
0.1u
C31
0.1u
R8
0R8
0
Y1
SG
-210
24M
Hz
Y1
SG
-210
24M
HzOE
1
OU
T3
GN
D2
VD
D4
CN
1
A1-
34P
A-2
.54D
SA
(71)
CN
1
A1-
34P
A-2
.54D
SA
(71)
12
34
56
78
910
1112
1314
1516
17 19 21 23 2526
2728
2930
3132
333418 20 22 24
Y2
XR
2A-1
405
Y2
XR
2A-1
405
1 2 3 4 5 6 7891011121314
R12
0R12
0
D2
SM
L-31
0DT
D2
SM
L-31
0DT
C37
0.1u
C37
0.1u
C33
0.01
u
C33
0.01
u
R11
0R
110
TP9
HK
-2-S
TP9
HK
-2-S
J4 WL-
1-3P
J4 WL-
1-3P1 2 3
SH5
.100
in. J
umpe
r Shu
nt
SH5
.100
in. J
umpe
r Shu
nt
R14
0R14
0
TP4
HK
-2-S
TP4
HK
-2-S
P2
PRPN
202P
AEN
-RC
P2
PRPN
202P
AEN
-RC
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
J5 WL-
1-2P
J5 WL-
1-2P 1
2
D3
SM
L-31
0PT
D3
SM
L-31
0PT
TP7
HK
-2-S
TP7
HK
-2-S
R19
270
R19
270
TP5
HK
-2-S
TP5
HK
-2-S
C32
0.1u
C32
0.1u
R20
270
R20
270
TP6
HK
-2-S
TP6
HK
-2-S
R17
33 1
%R
1733
1%
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 19
S1D13517 Display Controller
Figure 6-3: S5U13517P00C100 Schematic Diagram (3 of 3)
5 5
4 4
3 3
2 2
1 1
DD
CC
BB
AA
PCLK
PDE
PHS
PV
S
PDG
7PD
G6
PDG
5
PD
B6
PD
B5
PD
B7
PDR
4PD
R3
PDG
4PD
G3
PDR
2
PDG
2
PD
B3
PD
B4
PD
B2
PDR
5PD
R6
PDR
7
PD
R7
PD
R6
PD
R5
PD
R4
PD
R1
PD
R3
PD
R2
PD
R0
PD
G2
PD
G5
PD
G7
PD
G0
PD
G6
PD
G1
PD
G3
PD
G4
PDB
2
PDB
5
PDB
7
PDB
0
PDB
6
PDB
1
PDB
3PD
B4
GP
O2
GP
O3
GP
O1
GP
O0
GP
O0
GP
O2
GP
O1
GP
O3
PDG
1PD
R1
PD
B1
PDG
0PD
R0
PD
B0
MD
8
MD
4
MA
0
MA
9
MD
9
MD
12
MD
6
MD
1
MD
11
MA
7
MD
3
MD
13
MA
2
MD
15
MA
1
MD
14
MD
5
MA
10
MA
4
MD
7
MA
5M
A3
MA
6
MD
2
MA
11
MA
8
MD
10
MD
0
3.3V
DD
12V
DD
IOV
DD 12
VD
D
3.3V
DD
3.3V
DD
IOV
DD
IOV
DD
3.3V
DD
3.3V
DD
3.3V
DD
PCLK
PD
R[7
:0]
PD
G[7
:0]
PD
B[7
:0]
PDE
PHS
PV
S
MD
QM
1M
CLK
OM
CK
E
GP
O[3
:0]
PW
M
MD
[15:
0]
MB
A0
MC
AS
#
MB
A1
MA
[11:
0]MR
AS
#M
CS
#
MD
QM
0M
WE
#
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
LCD
, DR
AM
A4
33
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
LCD
, DR
AM
A4
33
Wed
nesd
ay, A
pril
22, 2
009
Title
Siz
eD
ocum
ent N
umbe
rR
ev
Dat
e:S
heet
of
<Doc
>1.
2
LCD
, DR
AM
A4
33
Wed
nesd
ay, A
pril
22, 2
009
12VD
D
LCD
12V
DD
Ctrl
GP
O
Ext
LC
D
R62
22k
R62
22k
R55
0R
550
C40
47u
10v
C40
47u
10v
R27
0R
270
R44
0R
440
R53
0R
530
C54
0.01
u
C54
0.01
u
CN
3
HIF
3FC
-40P
A-2
.54D
SA
CN
3
HIF
3FC
-40P
A-2
.54D
SA
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
R37
0R
370
R36
0R
360
C44
0.01
u
C44
0.01
u
R39
0R
390
C48
0.01
u
C48
0.01
u
R46
0R
460
R60
0R60
0
R28
0R
280
R63
47k
R63
47k
R56
0R
560
C42
1u 5
0VC
421u
50V
U4
TPS
6104
0
U4
TPS
6104
0SW1
GN
D2
FB3
EN4
VIN
5
R29
0R
290
R57
0R
570
R45
0R
450
R38
0R
380
C51
0.1u
C51
0.1u
C43
0.1u
C43
0.1u
R41
0R
410
C53
0.1u
C53
0.1u
U3
IS42
S16
800E
(128
Mbi
t SD
RA
M)
U3
IS42
S16
800E
(128
Mbi
t SD
RA
M)
VDD
1D
Q0
2VD
DQ
3D
Q1
4D
Q2
5VS
SQ6
DQ
37
DQ
48
VDD
Q9
DQ
510
DQ
611
VSSQ
12D
Q7
13VD
D14
DQ
ML
15W
E#16
CA
S#17
RA
S#18
CS
#19
BA0
20BA
121
A10
22A0
23A1
24A2
25A3
26VD
D27
VSS
28A4
29A5
30A6
31A7
32A8
33A9
34A1
135
NC
36C
KE37
CLK
38D
QM
H39
NC
40VS
S41
DQ
842
VD
DQ
43D
Q9
44D
Q10
45V
SSQ
46D
Q11
47D
Q12
48V
DD
Q49
DQ
1350
DQ
1451
VSS
Q52
DQ
1553
VSS
54
F1 AC
F451
832-
222
F1 AC
F451
832-
222
12
3
C50
0.01
u
C50
0.01
u
C46
0.01
u
C46
0.01
u
R30
0R
300
R52
0R
520
R31
0R
310
R58
0R
580
R21
0R
210
L3LQ
H32
CN
100K
23L
L3LQ
H32
CN
100K
23L
R47
0R
470
C41
10p
C41
10p
R40
0R
400
D4
MB
R05
30D
4M
BR
0530
R24
0R
240
R23
0R
230
C49
0.1u
C49
0.1u
R59
0R59
0
R33
0R
330
R48
0R
480
TP10
HK
-2-S
TP10
HK
-2-S
R54
0R
540
VR1
200k
VR1
200k
1 3
2
F2 AC
F451
832-
222
F2 AC
F451
832-
222
12
3
R32
0R
320
C55
0.1u
C55
0.1u
C52
0.01
u
C52
0.01
u
C45
0.1u
C45
0.1u
R22
0R
220
R42
0R
420
R51
0R
510
CN
5
A1-
10P
A-2
.54D
SA
(71)
CN
5
A1-
10P
A-2
.54D
SA
(71)
12
34
56
78
910
R49
0R
490
R25
0R
250
R43
0R
430
R35
0R
350
R26
0R
260
C56
0.01
u
C56
0.01
u
CN
4
A1-
10P
A-2
.54D
SA
(71)
CN
4
A1-
10P
A-2
.54D
SA
(71)
12
34
56
78
910
R50
0R
500
R61
887kR
6188
7kC
47
0.1u
C47
0.1uR
340
R34
0
20 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
S1D13517 Display Controller
Chapter 7 References
7.1 Documents• Epson Research and Development, Inc., S1D13517 Hardware Functional Specification, document number
X92A-A-001-xx
• Epson Research and Development, Inc., S5U13U00P00C100 USB Adapter Board User Manual, document number I00Z-G-018-xx
7.2 Document Sources• Epson Research and Development Website: http://www.erd.epson.com
S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON 21
S1D13517 Display Controller
Change Record
X92A-G-001-01 Revision 1.0 - Issued: May 8, 2009
• initial release
22 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
Document Code: X92A-G-001-01Issued 2009/04/28
International Sales Operations
AMERICA EPSON ELECTRONICS AMERICA, INC. 2580 Orchard Parkway San Jose, CA 95131,USA Phone: +1-800-228-3964 FAX: +1-408-922-0238
EUROPEEPSON EUROPE ELECTRONICS GmbH Riesstrasse 15, 80992 Munich,GERMANY Phone: +49-89-14005-0 FAX: +49-89-14005-110
ASIA EPSON (CHINA) CO., LTD.7F, Jinbao Bldg., No.89 Jinbao St.,
Beijing 100005, CHINAPhone: +86-10-6410-6655 FAX: +86-10-6410-7320
SHANGHAI BRANCH7F, Block B, High-Tech Bldg., 900, Yishan Road, Shanghai 200233, CHINA Phone: +86-21-5423-5522 FAX: +86-21-5423-5512
EPSON HONG KONG LTD.20/F, Harbour Centre, 25 Harbour Road Wanchai, Hong Kong Phone: +852-2585-4600 FAX: +852-2827-4346 Telex: 65542 EPSCO HX
SHENZHEN BRANCH12F, Dawning Mansion, Keji South 12th Road,Hi-Tech Park, Shenzhen 518057, CHINAPhone: +86-755-2699-3828 FAX: +86-755-2699-3838
EPSON TAIWAN TECHNOLOGY & TRADING LTD.14F, No. 7, Song Ren Road, Taipei 110, TAIWANPhone: +886-2-8786-6688 FAX: +886-2-8786-6660
EPSON SINGAPORE PTE., LTD.1 HarbourFront Place, #03-02 HarbourFront Tower One, Singapore 098633 Phone: +65-6586-5500 FAX: +65-6271-3182
SEIKO EPSON CORP. KOREA OFFICE 50F, KLI 63 Bldg., 60 Yoido-dong Youngdeungpo-Ku, Seoul, 150-763, KOREA Phone: +82-2-784-6027 FAX: +82-2-767-3677
SEIKO EPSON CORP. SEMICONDUCTOR OPERATIONS DIVISION
IC Sales Dept.IC International Sales Group 421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN Phone: +81-42-587-5814 FAX: +81-42-587-5117
Dongcheng District,