route 642-902 training » policy based routing sim.pdf

8/10/2019 ROUTE 642-902 Training Policy Based Routing Sim.pdf

1/24

Home> Policy Based Routing Sim

Policy Based Routing Sim

May 8th, 2014 in LabSimGo to comments

Question

Company Acan has two links which can take it to the Internet. The company policy demands that you use

web traffic to be forwarded only to Frame Relay link if available and other traffic can go through any links.

No static or default routing is allowed.

Answer and Explanation:

Notice: The answer and explanation below are fromPeterPan and Helper.Please say thank to them!

All the HTTP traffic from the EIGRP Network should go through Frame Relay link if available and all the

other traffic should go through either link.

The only router you are able to administrate is the Border Router, from the EIGRP Network you may only

send HTTP traffic. As the other people mentioned, actually it is not a BGP lab. You are not able to execute

the command router bgp 65001

TE 642-902 Training Policy Based Routing Sim http://www.digitaltut.com/route-policy-based-ro

4 9/5/2014 1
http://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-sim


2/24

1) Access list that catches the HTTP traffic:

BorderRouter(config)#access-list 101 permit tcp any any eq www

Note that the server was not directly connected to the Border Router. There were a lot of EIGRP routes on it.

In the real exam you do not know the exact IP address of the server in the EIGRP network so we have to use

the source as any to catch all the source addresses.

2) Route map that sets the next hop address to be ISP1 and permits the rest of the traffic:

BorderRouter(config)#route-map pbr permit 10

BorderRouter(config-route-map)#match ip address 101

BorderRouter(config-route-map)#set ip next-hop 10.1.101.1

BorderRouter(config-route-map)#exit

(Update: We dont need the last command route-map pbr permit 20to permit other traffic according to

Cisco:

If the packets do not meet any of the defined match criteria (that is, if the packets fall off the end of a route

map), then those packets are routed through the normal destination-based routing process. If it is desired not

to revert to normal forwarding and to drop the packets that do not match the specified criteria, then interfaceNull 0 should be specified as the last interface in the list by using the set clause.

Reference: http://www.cisco.com/en/US/products/ps6599/products_white_paper09186a00800a4409.shtml)

3) Apply the route-map on the interface to the server in the EIGRP Network:


BorderRouter(config)#int fa0/0

BorderRouter(config-if)#ip policy route-map pbr

BorderRouter(config-if)#exit

BorderRouter(config)#exit

4) There is a Host for Testing, click on this host to open a box in which there is a button named Generate

HTTP traffic. Click on this button to generate some packets for HTTP traffic. Jump back to the

BorderRouter and type the command show route-map.

BorderRouter#show route-map

In the output you will see the line Policy routing matches: 9 packets. It means that the route-map we

configured is working properly.

Note:We have posted a Policy Based Routing lab on GNS3 similar to this sim with detailed explanation, you

can read it here.

Other lab-sims on this site:

EIGRP Stub Sim

OSPF Sim

EIGRP OSPF Redistribution Sim

IPv6 OSPF Virtual Link Sim


4 9/5/2014 1
http://www.cisco.com/en/US/products/ps6599/products_white_paper09186a00800a4409.shtml)http://www.cisco.com/en/US/products/ps6599/products_white_paper09186a00800a4409.shtml)http://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simhttp://www.cisco.com/en/US/products/ps6599/products_white_paper09186a00800a4409.shtml)


3/24

EIGRP Simlet

Comments

Comment pages

Previous1 789 28

Farmer

November 8th, 2013

@Dev,

No, it is not. What your route-map statements dont catch, your routing table will forward unless you

have some kind of explicit deny in a route-map statement.

route-map pbr permit 20 is not in the answer above for a good reason, it seems like everyone that

listens to CBT Nuggets comes out with route-map pbr permit 20 statement, the only reason why you

would want to add this route-map to the above answer, is if the question asks you for a preferred route

for all other traffic which is not HTTP, meaning, everything else should go out another ISP, which is

not that of HTTP but if you do this preferred route, you are contradicting what the question might ask

you other wise, and that is all other traffic MUST still use any ISP meaning, if you allow route-map

20 as a preferred route, you are not failing over any more. All your other traffic which is not HTTP

only goes to one ISP, and if that ISP is down, all your other traffic which is not HTTP is also down.

Your preconfigured routing table in your exam is setup correctly as it is, all you need to do is, forward

HTTP traffic to ISP 2, and leave it at that, otherwise you dont have failover.

F

1.

Haigazous

November 8th, 2013

Dear digitaltut

1) Access list that catches the HTTP traffic:

BorderRouter#access-list 101 permit tcp any any eq www

This command must be in global configuration mode..

2.

Ali Donia

November 12th, 2013

get this sim in my exam exactly no any problem (route-map pbr permit 20) working so

i got 1000

3.

Mohammad Dasdarnejad

November 15th, 2013

You dont have any route for all other traffic in your routing table so you need second statement,

also the scenario says send the http traffic if the frame-relay link is available if not you have to use the

other link.

I think the correct configuration is:

4.


4 9/5/2014 1


4/24

access-list 100 permit tcp any any eq www

route-map internal-traffic permit 10

match ip address 100

set ip next-hop 10.1.101.1 10.1.102.1


set ip next-hop 10.1.102.1

int fa0/0

ip policy route-map internal-traffic

sameboatasyou

November 15th, 2013

what is the password for the routers? cisco does not work..

5.

digitaltut

November 16th, 2013

@sameboatasyou: The password is shawn.

6.

Teekash

November 19th, 2013

Hi guys when i log onto the Host for testing it requests for a password, what is the workaround to that

as i am stuck!!!!

7.

Teekash

November 19th, 2013

How do i generate traffic that will be caught by the route-map statements created??

8.

Bayo

November 22nd, 2013

The second statement is just used to match other generated traffic. you can choose to use it if you want

to see evidience that the other traffics passing through the route map. when training with the sims you

should use the www instead of echo in your access list. From the host for testing router

telnet 10.1.101.1 www

this would generate http traffic dat would be caught in your routemap line 10.

ping either ISP1 or ISP2 to generate traffic that would match routemap line 20 ( no harm if you choose

to use it, but it lets you know that other traffic which are not http are still being forwarded by other

means. its not compulsory but I think its necessary for verification purposes in the exam).

9.

Bayo

November 22nd, 2013

also telnet isp 2 on port 80

telnet 10.1.102.1 www

this connection would not be successful since all http traffic are forwarded through the frame relay and

10.


4 9/5/2014 1


5/24

has been caught by the route map line 10. this is also a proof that all http traffic are forwarded through

the frame relay as required.

Bayo

November 22nd, 2013

but intrestingly ISP 2 telnet 10.1.102.1 www still connects despite being caught by the route map

line 10.

11.

Bayo

November 22nd, 2013

I jst got something. there is a defaul route forwarding every traffic out both isp1and isp2 so if the traffic

escape through the routemap it is then fowarded by any available link ISP1 or ISP2.

that was why telnet 10.1.102.1 www could still connect.

to force all http traffic through the frame relay, all the interfaces serial 0/0 and fa 0/1 should have the

policy on them. Someone please confirm

12.

paracyte

November 22nd, 2013

hi

passed today with 988, few new questions (around 4), new 1 drag n drop, the rest the same as in the

igor file, distance eigrp 90 105 worked for me, also in policy based lab I have added route-map pbr

permit 20 and it still worked so unsure if this is needed but I guess it does not hurt. had no issues with

any commands whatsoever during the labs. Areas and IP addresses change in the labs but no problem

just adapt to the scenario. All 5 labs included, no hotspots.

goodluck.

13.

Midget

November 25th, 2013

@Bayo, The reason you can still connect to ISP2 is due to both the connected interfaces on the

BorderRouter that are part of AS 65000. If you issue the command sho ip eigrp topology 65000 on

ISP1, you will see that it knows about the 10.1.102.0/24 subnet via 10.1.101.254. This will cause the

ISP1 router to route that traffic back out interface S0/0 to the BoarderRouters interface S0/0.

BoarderRouters interface S0/0 does not take part in the policy based routing that was set on its

interface F0/0. This will create asymmetric routing for your ingress and egress web traffic that is

destined for 10.1.102.1.

Long story short the traffic flow goes like this:

Host > Transit_router > BoarderRouter > ISP1 > BoarderRouter > ISP2.

Return traffic will be like:

ISP2 > BoarderRouter > Transit_router > Host.

14.

MooseMeat

November 27th, 2013

15.


4 9/5/2014 1


6/24

Gents as i follow the able step by step and try the echo instead of www it doesnt work, when i check

the PBR table nothing is being picked up pardon my ignorance and lack of experience, as read some

of the comments with explanation i seem to be getting further confused. anyone can shine some easy

DUM explanation please.

Haki

November 28th, 2013

Notice :

BorderRouter#access-list 101 permit tcp any any eq www (X)

BorderRoute(config)r#access-list 101 permit tcp any any eq www (O)

16.

Haki

November 28th, 2013

BorderRouter#access-list 101 permit tcp any any eq www (X)

BorderRouter(config)#access-list 101 permit tcp any any eq www (O)

17.

PT

December 3rd, 2013

@ Farmer

Good explanation, thx for the clarification!

18.

Dave

December 3rd, 2013

please use:

route-map pbr permit 20

This came in my exam today and I got full marks (I think)

19.

rockercya

December 4th, 2013

Hi Guys

do we have to use IP SLA for the policy based routing lab in the exam?

20.

Dave

December 4th, 2013

Hi Rockercya, you dont have to use ip sla in this lab. use the solution that is give by digitaltut but just

add:

route-map pbr permit 20

and you will be fine

21.

jt

December 4th, 2013

in GNS to generate traffic try telneting to the network it wont connect but your route map should

22.


4 9/5/2014 1


7/24

capture enough traffic either for both route-map pbr permit 10 or 20. to generate hhtp traffic try

Host_For_Testing>telnet 10.1.101.0 80 and for other traffic try Host_For_Testing>telnet 10.1.101.0

443

patrick

December 5th, 2013

Mohammad Dasdarnejad : tottaly agree thks !

23.

rockercya

December 5th, 2013

Thanks Dave

24.

junaid

December 9th, 2013

can any one tell me how can i download this sim for practice????????????????? plz help me

25.

AnonymousDecember 13th, 2013

Hello All! Where can I download the specifed Cisco image? thanks

26.

Ruban

December 14th, 2013

Hi Please Clear my doubt

route-map pbr permit 20 is must or not ?

if we add route-map pbr permit 20 means any match ip and set criteria want to be assing ?

27.

sepp

December 17th, 2013

@Ruban,

Most people say they got full marks when they used it..so I guess you should use it to avoid any doubts

28.

garrincha33

January 7th, 2014

im setting up a website to stream all the CCNP videos (from Ipad ect aswell)

if you want to pre register for an account email me at [email protected]

just put CCNP in the mail either subject or body. I ll email you once up and running vids should be

online in the next 2 weeks. They helped me pass all my exams so defiantely worth watching

29.

psarr10

January 8th, 2014

To PeterPan and Helper

30.


4 9/5/2014 1
mailto:[email protected]://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simmailto:[email protected]


8/24

Thank you very much!!!

If you need me

January 14th, 2014

passed today with 987 thanks

I also used study guides and http://www.sendmeanything.comfor the vids (great site)

lets you stream the videos so pretty essential in order to acheive a good mark

good luck people

31.

badsanta

January 24th, 2014

In my exam the fa 0/0 interface had an valid ip address

32.

tabdig

January 27th, 2014

I agree with digitaltut here, I dont think you need route-map pbr permit 20 on the end.

See this document, its very helpful around route maps, prefix lists and distribute lists:

http://www.routeralley.com/ra/docs/route_maps.pdf

Quote:

If using a route-map for policy-based routing or adjusting attributes, any routes/traffic not specifically

matched will REMAIN UNCHANGED.

If using a route-map for redistribution, any routes not specifically matched (and permitted) will not be

redistributed.

33.

Fadil

January 28th, 2014

hi all

can any one send me the last dump? examcollection is not updated

please if you have the last dump of pass4sure send a copy

my e-mail is fadil.44 @ hotmail

34.

IRK

January 28th, 2014

Hey guys, I see that for this LAB HTTP traffic generator is needed.

IP SLA can be very helpful in this case.

IP SLA should be configured on Host_for_testing using this configuration:

!HTTP GET Traffic

ip sla monitor 5

type http operation get url http://10.1.101.1

35.


4 9/5/2014 1
http://www.sendmeanything.com/http://www.routeralley.com/ra/docs/route_maps.pdfhttp://10.1.101.1/http://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simhttp://10.1.101.1/http://www.routeralley.com/ra/docs/route_maps.pdfhttp://www.sendmeanything.com/


9/24

frequency 60

exit

ip sla monitor schedule 5 start-time now life forever

end

jafari

January 31st, 2014

Hi, I need a CCNP techie in japan and korea for an urgent contract position, kindly let me know ASAP

if you are free to handle it or can refer me to any one. ([email protected])

Urgent!!!

Thanks.

36.

Anonymous

February 1st, 2014

anyone have latest pass4sure or certleak dumps? I need ROUTE/SWITCH/TSHOOT/DESIGN please!

thanks in advance. please send to:[email protected]

37.

StillDign

February 2nd, 2014

If you have the GNS3.

Host_For_Testing#config t

Host_For_Testing(config)#ip route 0.0.0.0 0.0.0.0 10.1.101.1

Host_For_Testing#telnet 1.1.1.1 www

Trying 1.1.1.1, 80

% Destination unreachable; gateway or host down

BorderRouter#sh route-map

[email protected]

38.

dhl123

February 18th, 2014

hye guys.i also have same problem with @stilldign.idownload this lab and i try to follow all command

same with this lab.then got error.



Host_For_Testing#telnet 10.1.101.1 80

Trying 1.1.1.1, 80


please help me guys

39.


4 9/5/2014 1
mailto:([email protected])mailto:[email protected]:[email protected]:@stilldign.ihttp://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simmailto:@stilldign.imailto:[email protected]:[email protected]:([email protected])


10/24

dhl123

February 18th, 2014

hye guys.i also have same problem with @stilldign.idownload this lab and i try to follow all command

same with this lab.then got error.



Host_For_Testing#telnet 10.1.101.1 80

Trying 10.1.101.1, 80


please help me guys

40.

Anonymous

February 24th, 2014

anyone help mie m using these labs bt m nt getting the actual results and on the engines which one

comes please m sitting on the 28 the help send to [email protected]

41.

AnonymousFebruary 24th, 2014

multiple choice which engine is coming plese help

42.

naved

March 4th, 2014

Hii guyscould you guys pls tell me in this lab routing will be pre-configured or we have to

configureis it possible to confiugure frame relay without frame relay switch

43.

DavidMarch 8th, 2014

The route-map clause uses a permit action, which tell IOS to indeed apply PBR logic to these matched

packets. (Had the route-map command listed a deny action, IOS would simply route the packet as

normal-it would not filter the packet). In conclusion, route-map pbr permit 20 is not neccesary.

44.

LABs Valid?

March 14th, 2014

Are this LABs still valid? Some folks say they changed today :(

45.

Tai

March 17th, 2014

I cant use the route-map command on packet tracer- gives error message (like unknown command)-

anybody knows about it pls?

46.

Anonymous

March 27th, 2014

People, stop confusing yourselves. The point of the Lab is to divert traffic on port 80 (WWW), NOT to

47.


24 9/5/2014 1
mailto:@stilldign.imailto:[email protected]://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simmailto:[email protected]:@stilldign.i


11/24

block or deny traffic. I hope this explanation helps you to understand it better. you should complete the

lab as it is above

From the Host for testing;

Telnet 10.1.101.1 80 This will match the route map and you will see port 80 open on ISP1

Telnet 10.1.102.1 80 This will also match the route map and you will see port 80 open on ISP2. you

will see the port open on ISP2 because when the traffic arrives at the border router it matches the route

policy on fa0/0. the traffic is then sent to ISP1 (10.1.101.1). ISP1 has a route to ISP2 so it sends the

traffic back to the border router. this time the traffic arrives on S0/0/0. This interface has no routing

policy so it forward the traffic to ISP2.

If you look closely enough you will see that the border router has two default routes.

so if you shut down s0/0/0 on the border router and telnet 10.1.102.1 80 you will see the port open. this

is because when the border router route map sets the next hop to 10.1.101.1 and tries to forward the

traffic it notices that 10.1.101.0/24 is no longer in the routing table so it forwards the traffic out the

default route of 0.0.0.0 0.0.0.0 10.1.102.1

hope this helps

omer

March 29th, 2014

can i use eq 80 instead of eq www

48.

Anonymous

March 30th, 2014

can somebody who already have the dumps downloaded into their computer send me in attached

e-mail, because now when i try to download it, it asks for the newer version of visual manager, it will

be a big help, i am using 3.4.2 version so if you have this also and your file opens on it please attachthat and send me i have CCNP switch Dumps lf you want it

[email protected]

49.

jim

April 3rd, 2014

@omer, yes you can use either way

50.

KF

April 8th, 2014

Need clarification . Why are we applying the policy on Int fa 0/0 . Dont you guys think that we should

apply on S0/0 interface ? Instead of fa0/0

Have exam tomorrow . Please let me know

BorderRouter(config)#route-map pbr permit 10

BorderRouter(config-route-map)#match ip address 101

BorderRouter(config-route-map)#set ip next-hop 10.1.101.1

51.


24 9/5/2014 1


12/24



BorderRouter(config)#int fa0/0

BorderRouter(config-if)#ip policy route-map pbr

BorderRouter(config-if)#exit

KF

April 8th, 2014

In above comment . We are set ip next-hop 10.1.101.1 is S0/0 address but on the interface we are

applying on fa0/0 . Is that correct ?

52.

ITJ

April 8th, 2014

@KF you set it on fa0/0 cuz it is the ingress interface.

53.

hey every one

April 8th, 2014

can you please send the latest dump pdf please on [email protected]

54.

Hakcy

April 9th, 2014

I m doing same configuration as it says above none of my packets are matching when i see show route

map. i am confused . need help.

55.

Jim

April 9th, 2014

@Hacky, have you applied route-map on inside interface? i thin you didnt

56.

omer

April 10th, 2014

there is no need of route-map pbr permit 20

i got these lan today and i got 1000

57.

Mian

April 12th, 2014

@omer . I agree with you ..

I have tried the same scenario in GNS 3 without route-map pbr permit 20

and also in exam I did not use route-map pbr permit 20 ..and got 1000/1000

58.

Ehsan

April 12th, 2014

59.


24 9/5/2014 1


13/24

Dears

The questions says The company policy demands that you use web traffic to be forwarded only to

Frame Relay link if available, I thinks if available keyword means using IP SLA, because without

using IP SLA we cant monitor availability

Ehsan

April 12th, 2014

Another question,

I did mentioned configuration on GNS3 but after enabling pbr, i still could telnet on port 80 on both

ISP1 and ISP2 :

BorderRouter#sho route-map PBR

route-map PBR, permit, sequence 10

Match clauses:

ip address (access-lists): 100

Set clauses:

ip next-hop 10.1.101.1

Policy routing matches: 21 packets, 1155 bytes

BorderRouter#

60.

Jim

April 13th, 2014

@Ehsan, you will be able to connect other ISP on port 80 because when traffic for ISP 2 goes to ISP1,

ISP1 has routes for ISP2 in its routing table which it learnt from Border Router via BGP. so in this case

the request for telnet ISP2 on port 80 goes to ISP1 and ISP1 checks its routing table and see it can

reach ISP2 via BorderRouter. it sends packets to BorderRouter. BorderRouter then forward them toISP2. the point is in either case, the match hits should increase if the traffic is for port 80.

61.

Jim

April 13th, 2014

@everyone, had this lab. it is exactly the same as digitaltut says. we dont need to add:

route-map PBR permit 20.

62.

Ehsan

April 13th, 2014

@Jim, Thanks dear, you are right, i test it by change the policy to icmp traffic. but in the real work

gateway route should not act as transit router. and about my first question, I think for availability check

we should configure IP SLA

63.

Santanu

April 20th, 2014

Peter, Helper and all contributors, Thanks a lot for explaining the SIMs

64.


24 9/5/2014 1


14/24

SASA

April 23rd, 2014

Here what I done.

First I change HTTP to TELNET, which I can initiate from Host_For_Testing router.

Of course, I enabled telnet to the routers ISP1 and ISP2.

Then create condition list to match:

ip access-list extended TELNET

permit tcp any any eq telnet

and a route-map:

route-map POLICY permit 10

match ip address TELNET


!

route-map POLICY permit 20

(seq.20 is important to match all other traffic that is not match in seq.10 and not to SET anything (leave

as it is)).

On Fa0/0 apply policy:

ip policy route-map POLICY

So far, we have SET the next hop address for any telnet traffic to the ISP1.

All other traffic may go where ever

Verification:

For this purpose, we must make the changes on ISP routers as they are routing traffic to each other so

test cannot be valid.

On ISP1 create:

ip route 10.1.102.1 255.255.255.255 Null0

and on ISP2 create:

ip route 10.1.101.1 255.255.255.255 Null0

Both are /32 networks, so keep that in the mind.

On ISP1/2

modify eigrp:

router eigrp 65000

no auto-summary

// remove present network statement

// add interface exact network statement, i.e.

network 10.1.101.1 0.0.0.0 // on ISP1

network 10.1.102.1 0.0.0.0 // on ISP2

65.


24 9/5/2014 1


15/24

with this modification, we cut the mutual ISP to ISP routing and with the are not advertise any of those

Null0 routes to the BorderRouter.

All is clear.

Now Policy verification from Host_For_Testing router:

test first any traffic;

ping 10.1.101.1 successfull, seq.20 show countersping 10.1.102.1 successfull, seq.20 show counters

test the telnet traffic:

telnet 10.1.101.1 successfull, seq.10 show counters

telnet 10.1.102.1 not pass, seq.10 show counters


16/24

KB-LOVE-CCNP-ROUTE

April 26th, 2014

Comrades i like all whts on Digitaltut

67.

certinless

May 1st, 2014

dear allcontact for

CCNA

CCNA SECURITY

CCNP

guides online training updated valid dumps & discounted vouchers for exams.

skype:certcry

[email protected]

68.

Anonymous

May 2nd, 2014

Just wrote, same lab with different IPs

Did commands as lab suggested but my route-map policy didnt math any packets and no idea where I

went wrong

69.

mone901

May 6th, 2014

@Everyone

Hello!!! For test lab in GNS3 I configured with:

_I have changed the access list 101 permit icmp any any echo

_I config a static route on ISP1 ip route 10.1.102.1 255.255.255.255 null0 so I cancel the route in

routing table and now from ISP1 dont ping the ISP2

In normal condition from BorderRouter I can ping ISP1 but no ISP2 (because the icmp echo traffic

should go always to ISP1) while the counters in route-map increase in both cases.

ping 10.1.102.1

Sending 5, 100-byte ICMP Echos to 10.1.102.1, timeout is 2 seconds:

U.U.U (the echo arrived in ISP1 but is eliminated from the static so its respond with U.U.U)

If shut the serial0/0 on BorderRouter now I can ping ISP2 (because link to ISP1 is down and the icmp

echo traffic goes now to ISP2) and the counters of route-map always increase.

I think it is a good test

hope this help

70.


24 9/5/2014 1


17/24

sylvios

May 22nd, 2014

@all

Hi! I am wondering if the following will be considered valid response and give all the marks.

I noticed that BorderRouter should police traffic coming from 192.168.0.0/16. So is it OK if I add:

access-list 101 permit tcp 192.168.0.0 0.0.255.255 any eq www

!

route-map PBR permit 10

match ip address 101


!

route-map PBR permit 20

set ip next-hop 10.1.101.1 10.1.102.1

and then apply it in the BorderRouter Fa0/0 interface?

I did it in GNS3 and it works as the lab wants. Web traffic (telnet 10.1.101.1 www) increases matches

on the 1st route-map entry (permit 10) and all other traffic (pings) increase matches on the 2nd

route-map entry (permit 20).

Isntt this what the lab asks?

Will this be considered valid?

Thanks guys

71.

Anoymous

May 27th, 2014

Hi guys! please can someone help me with a valid dump? Will be writing in few days. Kindly send to

[email protected]

72.

Calling.Dr.Howard.Dr.Fine.Dr.Howard

May 30th, 2014

The lab stated that all the other traffic should go through either link.

Your config does not allow for that.

73.

Alhasan

May 31st, 2014

really thanks for everything :) @sylvios

74.

meteor

June 2nd, 2014

Guys, if your are bored with cisco preps then get on this site and have some humor laden snack time.

http://geekzoneunlimited.blogspot.in/?m=1I know it gets a bit hectic to ram on the same stuff over and

75.


24 9/5/2014 1
mailto:[email protected]://geekzoneunlimited.blogspot.in/?m=1http://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simhttp://geekzoneunlimited.blogspot.in/?m=1mailto:[email protected]


18/24

over again while thinking breaking yourself with burden of exam day. Go through that link and ease

out a bit.

anonymous

June 7th, 2014

passed route same simulators

76.

BrianJune 8th, 2014

the answer above is correct, if theres 2 separate ip route 0.0.0.0 0.0.0.0 pointing both links.

Does any passers here who can confirm if theres any static routes defined in the boarder router?

If theres none, then we need a route-map pbr 20 with match statement pointing to both links.

77.

unstrunghero

June 8th, 2014

Can we use ?/help on the simulation?

78.

Anand

June 14th, 2014

Is there password for host for testing

79.

killer

June 16th, 2014

GUYS who pass exam , can u confirm me if below command works during exam lab plz ??

clear ip route *

clear ip ospf proc

clear ip eigrp neigh

thx in advance

80.

Mohsan

June 18th, 2014

pass today igor and digitalut are valid but extra thing in redistribution is telnet so i lose 65 got 935 allother are good

81.

kamui

June 19th, 2014

passed exam today with success , beware to apply ip policy on fa0/1 on exam and not on fa0/0 , u could

not save conf on this lab to validate generate traffic on host for testing and do sh route-map to see

matches packet increasing.

82.


24 9/5/2014 1


19/24

Material Used

-CCNP MAster Route Rene Molenaar ,amazing pdf and labs

-VCE Player 1.02

-GNS v0.86

-Cisco.Passguide.642-902.ROUTE.v2013-06-17.by.Igor.397q.vce

-Digital Tut

No drag and drop or EIGRP/OSPF hotspot , all labs and igor 397q still valid , thanks God and all of u

here for ur feedback !!! nxt move is to go for TSHOOT to finish my CCNP Journey !!

I got heavy IPV6 question,GRE, OSPF and Eigrp redistribution multichoice, acl ,route map, no bgp

question I was surprised ?

kamui

June 19th, 2014

I also put route-map pbr permit 20 , and I did not lose points for this labs

83.

INTERNETWORKING

June 21st, 2014

Passed CCNP route yesterday with 1000 marks

all the questions here are absolutely valid

All the simulations are valid as well.

There is a slight change in the ip addresses and given statements.

i strongly recommend everyone to do practice on GNS3.

Thanks Digitaltut and other people over here.

84.

AnonymousJune 22nd, 2014

Passed CCNP route

85.

Subrata Bangladesh

June 22nd, 2014

Passed CCNP route

86.

Anonymous

June 27th, 2014

Hey Guys,

I passed my 642-902 IP Routing exam this week and here are my comments.

1- All LABs from TUT9 are still Valid

2- LABs are coming in no order and in mix with other questions. Watch the time as one of the LAB

could be your last question. You dont wanna miss any LAB (they are high score)

3- A lot of IPV6 questions. I Mean about 20 out of 50 were IPV6 and about 5 questions about GRE

Tunnel & IPSec. the rest were mix of EIGRP, OSPF, IBGP, etc.

4- No Drag and Drop

87.


24 9/5/2014 1


20/24

5- I recommend Igors test (372 questions), they give you an idea what you could expect in the exam.

6- Telnet is not active (for OSPF & EIGRP redistribution), you cannot change the line vty 0 4 either.

7- copy running-config startup-config doesnt work. Except one LAB, I couldnt save the settings and I

am not sure If I lost any score for that

8- CTRL+Z (Apply the command line and exit from config mode) doesnt work in any LAB

9- write memory doesnt work

emma

July 2nd, 2014

Pls i need the new VCE 3.4 setup. I have an exam very soon. help send the setup to

[email protected]

88.

SUCCESS 2014

July 15th, 2014

Hello friends, what is the latest dump for routing?

89.

lilou

July 18th, 2014

Hello all !

We should add the :



or not please ?

thx .

90.

victor

August 10th, 2014

Hi Guys.

anyone can say to me if i need to add the the command route-map pbr permit 20?

If, however, I added the command Is it bad?

91.

Anonymous

August 11th, 2014

Hey guys, there is another way to pratice this lab:

http://cafecomredes.blogspot.com.br/2014/06/boson-netsim-melhor-simulador-labs.html

There are many labs on Boson Netsimulator (crack)

92.

AGC

August 14th, 2014

Use debug ip policy on Border Router and direct different traffic.See the result for yourself.

93.


24 9/5/2014 1
mailto:[email protected]://cafecomredes.blogspot.com.br/2014/06/boson-netsim-melhor-simulador-labs.htmlhttp://www.digitaltut.com/route-policy-based-routing-simhttp://www.digitaltut.com/route-policy-based-routing-simhttp://cafecomredes.blogspot.com.br/2014/06/boson-netsim-melhor-simulador-labs.htmlmailto:[email protected]


21/24

Anonymous

August 16th, 2014

I DIDNT USE route-map pbr permit 20 in the exam

(GOT 1000/1000)

94.

angelic

August 18th, 2014

is the choices rambled in real exam?thanks in advance. my exam is on Friday please

95.

young

August 27th, 2014

did my route exam yesterday passed thanks digital tut now move on to tshoot and switch..anyone with

switch materials to help me with them mail me [email protected]

96.

yelzmani

August 29th, 2014

yo @young, are the labs the same.. same 5 labs?

97.

Cest DIEU qui est FORT

August 31st, 2014

Hi guys,

Ive passed my routing yesterday. Thanks a lot to Digitaltut.

No Drag and Drop. All the Labs are reliable, but for the Lab EIGRP OSPF Redistribution Sim, R2 to

R3 was Fast Ethernet so I had to add distance eigrp 90 105. There is enough time so you can also do it.

Good Luck

98.

neilg

September 4th, 2014

@ AGC

thank you and much appreciated , answers all the questions

99.

Comment pages

Previous1 789 28

No trackbacks yet.1.

Add a Comment

Name


24 9/5/2014 1


22/24

Subscribe to comments feed

EIGRP OSPF Redistribution SimIPv6 OSPF Virtual Link Sim

Premium Membership

Become a member to interact with all questions and practice labs!

Find out moreor Sign In

ROUTE 642-902

LabSimDrag and Drop Questions

Drag and Drop 2

Drag and Drop 3

DHCP Questions

OSPF Hotspot

OSPF Questions

OSPF Questions 2

OSPF Questions 3

OSPF Questions 4

OSPF Questions 5OSPF Questions 6

OSPF Questions 7

OSPF Questions 8

OSPF Questions 9

OSPF Questions 10

EIGRP Questions

EIGRP Questions 2

EIGRP Questions 3

EIGRP Questions 4


24 9/5/2014 1


23/24

EIGRP Questions 5

EIGRP Questions 6

EIGRP Questions 7

EIGRP Questions 8

EIGRP Questions 9

EIGRP Questions 10

EIGRP Simlet

BGP QuestionsBGP Questions 2

BGP Questions 3

BGP Questions 4

BGP Questions 5

BGP Questions 6

Redistribute Questions

Redistribute Questions 2



Policy Based Routing Questions

IPv6 Questions

IPv6 Questions 2

IPv6 Questions 3

IPv6 Questions 4

IPv6 Questions 5

Operations Questions

Operations Questions 2

Distribute List Questions

IPSec and GRE

6to4 Tunnel

Multicast Questions

ROUTE FAQs & Tips

Share your ROUTE Experience

ROUTE Self-Study

Basic Labs

ROUTE Knowledge

Network Resources

CCNA Website

ROUTE Website


24 9/5/2014 1


24/24

SWITCH Website

TSHOOT Website

CCNA Voice Website

CCNA Security Website

CCIP Website

CCDA Website

CCIE Website

Support Digitaltut

Your contribution will help keep this site updated!

Top

Copyright 2011-2014 ROUTE 642-902 Training

Privacy Policy. Valid XHTML 1.1 and CSS 3.UH


route 642-902 training » policy based routing sim.pdf

Documents