rc4558 dual general-purpose operational amplifier
TRANSCRIPT
+RIN
RGRF
VOUTVIN
Product
Folder
Sample &Buy
Technical
Documents
Tools &
Software
Support &Community
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014
RC4558 Dual General-Purpose Operational Amplifier1 Features 3 Description
The RC4558 device is a dual general-purpose1• Continuous Short-Circuit Protection
operational amplifier, with each half electrically similar• Wide Common-Mode and Differential Voltage to the μA741, except that offset null capability is notRanges provided.
• No Frequency Compensation Required The high common-mode input voltage range and the• Low Power Consumption absence of latch-up make this amplifier ideal for• No Latch-Up voltage-follower applications. The device is short-
circuit protected, and the internal frequency• Unity-Gain Bandwidth: 3 MHz Typcompensation ensures stability without external• Gain and Phase Match Between Amplifiers components.
• Low Noise: 8 nV/√Hz Typ at 1 kHzDevice Information(1)
2 Applications PART NUMBER PACKAGE (PIN) BODY SIZESOIC (8) 4.90 mm × 3.91 mm• DVD Recorders and PlayersSOIC (8) 3.00 mm × 3.00 mm• Pro Audio Mixers
RC4558 PDIP (8) 9.81 mm × 6.35 mmTSSOP (8) 3.00 mm × 4.40 mmSOP (8) 6.20 mm × 5.30 mm
(1) For all available packages, see the orderable addendum atthe end of the datasheet.
Noninverting Amplifier Schematic
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,intellectual property matters and other important disclaimers. PRODUCTION DATA.
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
Table of Contents7.2 Functional Block Diagram ......................................... 91 Features .................................................................. 17.3 Feature Description................................................... 92 Applications ........................................................... 17.4 Device Functional Modes.......................................... 93 Description ............................................................. 1
8 Application and Implementation ........................ 104 Revision History..................................................... 28.1 Typical Application ................................................. 105 Pin Configuration and Functions ......................... 3
9 Power Supply Recommendations ...................... 136 Specifications......................................................... 410 Layout................................................................... 146.1 Absolute Maximum Ratings ..................................... 4
10.1 Layout Guidelines ................................................. 146.2 Handling Ratings....................................................... 410.2 Layout Example .................................................... 146.3 Recommended Operating Conditions....................... 4
11 Device and Documentation Support ................. 156.4 Thermal Information .................................................. 411.1 Trademarks ........................................................... 156.5 Electrical Characteristics........................................... 511.2 Electrostatic Discharge Caution............................ 156.6 Operating Characteristics.......................................... 511.3 Glossary ................................................................ 156.7 Typical Characteristics .............................................. 6
12 Mechanical, Packaging, and Orderable7 Detailed Description .............................................. 9Information ........................................................... 157.1 Overview ................................................................... 9
4 Revision History
Changes from Revision F (September 2010) to Revision G Page
• Added Applications, Device Information table, Handling Ratings table, Feature Description section, DeviceFunctional Modes, Application and Implementation section, Power Supply Recommendations section, Layoutsection, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
• Removed Ordering Information table. .................................................................................................................................... 1
2 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
1
2
3
4
8
7
6
5
1OUT
1IN−
1IN+
VCC−
VCC+
2OUT
2IN−
2IN+
D, DGK, P, PS, OR PW PACKAGE
(TOP VIEW)
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
5 Pin Configuration and Functions
Pin FunctionsPIN
TYPE DESCRIPTIONNAME NO.
1IN+ 3 I Noninverting input1IN- 2 I Inverting Input1OUT 1 O Output2IN+ 5 I Noninverting input2IN- 6 I Inverting Input2OUT 7 O OutputVCC+ 8 — Positive SupplyVCC- 4 — Negative Supply
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: RC4558
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
6 Specifications
6.1 Absolute Maximum Ratingsover operating free-air temperature range (unless otherwise noted) (1)
MIN MAX UNITVCC+ 18
Supply voltage (2) VVCC– –18VID Differential input voltage (3) ±30 VVI Input voltage (any input) (2) (4) ±15 V
Duration of output short circuit to ground, one amplifier at a time (5) UnlimitedTJ Operating virtual junction temperature 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under Recommended OperatingConditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC–.(3) Differential voltages are at IN+ with respect to IN–.(4) The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.(5) Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded.
6.2 Handling RatingsMIN MAX UNIT
Tstg Storage temperature range -65 150 °CHuman body model (HBM), per AEC Q100-002 (1) 0 500
V(ESD) Electrostatic discharge VCharged device model (CDM), per AEC Q100-011 (2) 0 1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating ConditionsMIN MAX UNIT
VCC+ 5 15Supply voltage V
VCC– –5 –15RC4558 0 70
TA Operating free-air temperature °CRC4558I –40 85
6.4 Thermal InformationRC4558
THERMAL METRIC (1) D DGK P PS PW UNIT8 PINS
RθJA Junction-to-ambient thermal resistance 97 172 85 95 149 °C/W
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
6.5 Electrical Characteristicsat specified free-air temperature, VCC+ = 15 V, VCC– = –15 V
TESTPARAMETER TA(2) MIN TYP MAX UNITCONDITIONS (1)
25°C 0.5 6VIO Input offset voltage VO = 0 mV
Full range 7.525°C 5 200
IIO Input offset current VO = 0 nAFull range 300
25°C 150 500IIB Input bias current VO = 0 nA
Full range 800VICR Common-mode input voltage range 25°C ±12 ±14 V
RL = 10 kΩ 25°C ±12 ±14VOM Maximum output voltage swing 25°C ±10 ±13 V
RL = 2 kΩFull range ±10
25°C 20 300RL ≥ 2 kΩ,AVD Large-signal differential voltage amplification V/mVVO = ±10 V Full range 15B1 Unity-gain bandwidth 25°C 3 MHzri Input resistance 25°C 0.3 5 MΩCMRR Common-mode rejection ratio 25°C 70 90 dB
VCC = ±15 VkSVS Supply-voltage sensitivity (ΔVIO/ΔVCC) 25°C 30 150 μV/Vto ±9 VAVD = 100,RS = 100 Ω,Vn Equivalent input noise voltage (closed loop) 25°C 8 nV/√Hzf = 1 kHz,BW = 1 Hz
25°C 2.5 5.6VO = 0,ICC Supply current (both amplifiers) TA min 3 6.6 mANo load
TA max 2.3 525°C 75 170
VO = 0,PD Total power dissipation (both amplifiers) TA min 90 200 mWNo loadTA max 70 150
Open loop 85RS = 1 kΩ,VO1/VO2 Crosstalk attenuation 25°C dBf = 10 kHzAVD = 100 105
(1) All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified.(2) Full range is 0°C to 70°C for RC4558 and –40°C to 85°C for RC4558I.
6.6 Operating CharacteristicsVCC+ = 15 V, VCC– = –15 V, TA = 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNITtr Rise time VI = 20 mV, RL = 2 kΩ, CL = 100 pF 0.13 ns
Overshoot VI = 20 mV, RL = 2 kΩ, CL = 100 pF 5%SR Slew rate at unity gain VI = 10 V, RL = 2 kΩ, CL = 100 pF 1.1 1.7 V/μs
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: RC4558
0
5
10
15
20
25
30
1.E+00 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06
f – Frequency – Hz
VO
M–
Ou
tpu
tV
olt
ag
eS
win
g–
V
1 10 100 1k 10k 100k 1M
-15
-10
-5
0
5
10
15
6 8 10 12 14 16 18
VCC – Supply Voltage – V
VO
M–
Ou
tpu
tV
olt
ag
eS
win
g–
V
-20
-10
0
10
20
30
40
100 1000 10000
f – Frequency – kHz
Gain
–d
B
-200
-180
-160
-140
-120
-100
-80
-60
-40
-20
0
Ph
ase
–d
egGain
Phase
-20
-10
0
10
20
30
40
100 1000 10000
f – Frequency – kHz
Gain
–d
B
-200
-180
-160
-140
-120
-100
-80
-60
-40
-20
0
Ph
ase
–d
egGain
Phase
0
1
2
3
4
5
6
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
I CC
–S
up
ply
Cu
rren
t–
mA
0
1
2
3
4
5
6
0 2 4 6 8 10 12 14 16 18 20
VCC – Supply Voltage – V
I CC
–S
up
ply
Cu
rren
t–
mA
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
6.7 Typical Characteristics
Figure 1. Supply Current vs Supply Voltage Figure 2. Supply Current vs Temperature(TA = 25°C) (VCC = ±15 V)
Figure 3. Gain and Phase vs Frequency Figure 4. Gain and Phase vs Frequency(VCC = ±15 V, RL = 2 kΩ, CL = 22 pF) (VCC = ±15 V, RL = 10 kΩ, CL = 22 pF)
Figure 5. Output Voltage Swing vs Supply Voltage Figure 6. Output Voltage Swing vs Frequency(RL = 2 kΩ, TA = 25°C) (VCC = ±15 V, RL = 2 kΩ, TA = 25°C)
6 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
100
110
120
130
140
150
160
170
180
190
200
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
I IB–
Inp
ut
Bia
sC
urr
en
t–
nA
-0.003
-0.002
-0.001
0
0.001
0.002
0.003
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
VIO
–In
pu
tO
ffset
Vo
ltag
e–
V
-14
-13.75
-13.5
-13.25
-13
-12.75
-12.5
-12.25
-12
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
–V
OM
–O
utp
ut
Vo
ltag
eS
win
g–
V
0
10
20
30
40
50
60
70
80
90
100
110
120
1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07
f – Frequency – Hz
GM
–O
pen
Lo
op
Gain
–d
B
100 1k 10k 100k 1M 10M
12
14
16
18
20
22
24
26
28
30
32
100 1000 10000
Rload – Load Resistance –
VO
M–
Ou
tpu
tV
olt
ag
eS
win
g–
V
R – Load Resistance –L W
13
13.25
13.5
13.75
14
14.25
14.5
14.75
15
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
VO
M–
Ou
tpu
tV
olt
ag
eS
win
g–
V
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
Typical Characteristics (continued)
Figure 8. Output Voltage Swing vs TemperatureFigure 7. Output Voltage Swing vs Load Resistance(VCC = ±15 V, RL = 10 kΩ)(VCC = ±15 V, TA = 25°C)
Figure 9. Negative Output Voltage Swing vs Temperature Figure 10. Open Loop Gain vs Frequency(VCC = ±15 V, RL = 10 kΩ) (VCC = ±15 V, RL = 2 kΩ, CL = 22 pF, TA = 25°C)
Figure 11. Input Bias Current vs Temperature Figure 12. Input Offset Voltage vs Temperature(VCC = ±15 V) (VCC = ±15 V)
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: RC4558
0
2
4
6
8
10
12
14
1.E+01 1.E+02 1.E+03 1.E+04 1.E+05
f – Frequency – Hz
Vn
–In
pu
tN
ois
eV
olt
ag
e–
nV
/rt(
Hz)
10 100 1k 10k 100k
V– In
pu
t N
ois
eV
olt
ag
e –
nV
/n
ÖH
z
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
Typical Characteristics (continued)
Figure 13. Input Noise Voltage vs Frequency(VCC = ±15 V, TA = 25°C)
8 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
OUT
IN+
IN−
VCC−
VCC+
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
7 Detailed Description
7.1 OverviewThe RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to theμA741, except that offset null capability is not provided.
The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensuresstability without external components.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Unity-Gain BandwidthThe unity-gain bandwidth is the frequency up to which an amplifier with a unity gain may be operated withoutgreatly distorting the signal. The RC4558 device has a 3-MHz unity-gain bandwidth.
7.3.2 Common-Mode Rejection RatioThe common-mode rejection ratio (CMRR) of an amplifier is a measure of how well the device rejects unwantedinput signals common to both input leads. It is found by taking the ratio of the change in input offset voltage tothe change in the input voltage, then converting to decibels. Ideally the CMRR is infinite, but in practice,amplifiers are designed to have it as high as possible. The CMRR of the RC4558 device is 90 dB.
7.3.3 Slew RateThe slew rate is the rate at which an operational amplifier can change its output when there is a change on theinput. The RC4558 device has a 1.7 V/μs slew rate.
7.4 Device Functional ModesThe RC4558 device is powered on when the supply is connected. Each of these devices can be operated as asingle supply operational amplifier or dual supply amplifier depending on the application.
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: RC4558
R3
R1
R2
R4
15 V
VREF
12 V
+
+
VIN
+
VDIFF
±
VOUT-
VOUT+
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
8 Application and Implementation
NOTEInformation in the following applications sections is not part of the TI componentspecification, and TI does not warrant its accuracy or completeness. TI’s customers areresponsible for determining suitability of components for their purposes. Customers shouldvalidate and test their design implementation to confirm system functionality.
8.1 Typical ApplicationSome applications require differential signals. Figure 14 shows a simple circuit to convert a single-ended input of2 V to 10 V into differential output of ±8 V on a single 15-V supply. The output range is intentionally limited tomaximize linearity. The circuit is composed of two amplifiers. One amplifier acts as a buffer and creates avoltage, VOUT+. The second amplifier inverts the input and adds a reference voltage to generate VOUT–. BothVOUT+ and VOUT– range from 2 V to 10 V. The difference, VDIFF, is the difference between VOUT+ and VOUT–.
Figure 14. Schematic for Single-Ended Input to Differential Output Conversion
10 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
OUT OUTcm REF
V V 1V V
2 2
+ -+æ ö= =ç ÷
è ø
2 4 2DIFF O UT O UT IN REF
1 3 4 1
R R RV V V V 1 V 1
R R R R+ -
æ öæ ö æ ö= - = ´ + - ´ +ç ÷ç ÷ ç ÷
+è ø è øè ø
4 2 2out ref in
3 4 1 1
R R RV V 1 V
R R R R-
æ ö æ ö= ´ ´ + - ´ç ÷ ç ÷+ è øè ø
OUT REF
4
3 4
2
1 1
2
+IN
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
Typical Application (continued)8.1.1 Design RequirementsThe design requirements are as follows:• Supply voltage: 15 V• Reference voltage: 12V• Input: 2 V to 10 V• Output differential: ±8 V
8.1.2 Detailed Design ProcedureThe circuit in Figure 14 takes a single-ended input signal, VIN, and generates two output signals, VOUT+ andVOUT– using two amplifiers and a reference voltage, VREF. VOUT+ is the output of the first amplifier and is abuffered version of the input signal, VIN (see Equation 1). VOUT– is the output of the second amplifier which usesVREF to add an offset voltage to VIN and feedback to add inverting gain. The transfer function for VOUT– isEquation 2.VOUT+ = VIN (1)
(2)
The differential output signal, VDIFF, is the difference between the two single-ended output signals, VOUT+ andVOUT–. Equation 3 shows the transfer function for VDIFF. By applying the conditions that R1 = R2 and R3 = R4, thetransfer function is simplified into Equation 6. Using this configuration, the maximum input signal is equal to thereference voltage and the maximum output of each amplifier is equal to the VREF. The differential output range is2×VREF. Furthermore, the common mode voltage will be one half of VREF (see Equation 7).
(3)VOUT+ = VIN (4)VOUT– = VREF – VIN (5)VDIFF = 2×VIN – VREF (6)
(7)
8.1.2.1 Amplifier SelectionLinearity over the input range is key for good dc accuracy. The common mode input range and the output swinglimitations determine the linearity. In general, an amplifier with rail-to-rail input and output swing is required.Bandwidth is a key concern for this design. Because RC4558 has a bandwidth of 3 MHz, this circuit will only beable to process signals with frequencies of less than 3 MHz.
8.1.2.2 Passive Component SelectionBecause the transfer function of VOUT– is heavily reliant on resistors (R1, R2, R3, and R4), use resistors with lowtolerances to maximize performance and minimize error. This design used resistors with resistance values of36 kΩ with tolerances measured to be within 2%. But, if the noise of the system is a key parameter, the user canselect smaller resistance values (6 kΩ or lower) to keep the overall system noise low. This ensures that the noisefrom the resistors is lower than the amplifier noise.
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: RC4558
0
2
4
6
8
10
12
0 2 4 6 8 10 12
VO
UTt (
V)
VIN (V) C002
±12
±8
±4
0
4
8
12
16
0 2 4 6 8 10 12
VD
IFF
(V
)
VIN (V) C003
0
2
4
6
8
10
12
14
16
0 2 4 6 8 10 12
VO
UT
+ (
V)
VIN (V) C001
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
Typical Application (continued)8.1.3 Application CurvesThe measured transfer functions in Figure 15, Figure 16, and Figure 17 were generated by sweeping the inputvoltage from 0 V to 12 V. However, this design should only be used between 2 V and 10 V for optimum linearity.
Figure 15. Differential Output Voltage Node vs Input Figure 16. Positive Output Voltage Node vs Input VoltageVoltage
Figure 17. Positive Output Voltage Node vs Input Voltage
12 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
9 Power Supply Recommendations
The RC4558 device is specified for operation from ±5 V to ±15 V; many specifications apply from –0°C to 70°C.The Typical Characteristics section presents parameters that can exhibit significant variance with regard tooperating voltage or temperature.
CAUTIONSupply voltages outside of the ±18-V range can permanently damage the device (seethe Absolute Maximum Ratings ).
Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or highimpedance power supplies. For more detailed information on bypass capacitor placement, refer to the LayoutGuidelines.
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: RC4558
OUT1
OUT2IN1í
IN1+
VCCí
VCC+
IN2í
IN2+
RG
RIN
RF
GND
VIN
VS-GND
VS+
GND
Run the input traces as far away from the supply lines
as possible
Only needed for dual-supply operation
Place components close to device and to each other to
reduce parasitic errors
Use low-ESR, ceramic bypass capacitor
(or GND for single supply) Ground (GND) plane on another layer
+RIN
RGRF
VOUTVIN
RC4558SLOS073G –MARCH 1976–REVISED OCTOBER 2014 www.ti.com
10 Layout
10.1 Layout GuidelinesFor best operational performance of the device, use good PCB layout practices, including:
• Noise can propagate into analog circuitry through the power pins of the circuit as a whole and the operationalamplifier. Bypass capacitors are used to reduce the coupled noise by providing low impedance powersources local to the analog circuitry.– Connect low-ESR, 0.1-μF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for singlesupply applications.
• Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effectivemethods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes.A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digitaland analog grounds, paying attention to the flow of the ground current. For more detailed information, refer toCircuit Board Layout Techniques, (SLOA089).
• To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. Ifit is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular asopposed to in parallel with the noisy trace.
• Place the external components as close to the device as possible. Keeping RF and RG close to the invertinginput minimizes parasitic capacitance, as shown in Layout Example.
• Keep the length of input traces as short as possible. Always remember that the input traces are the mostsensitive part of the circuit.
• Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduceleakage currents from nearby traces that are at different potentials.
10.2 Layout Example
Figure 18. Operational Amplifier Schematic for Noninverting Configuration
Figure 19. Operational Amplifier Board Layout for Noninverting Configuration
14 Submit Documentation Feedback Copyright © 1976–2014, Texas Instruments Incorporated
Product Folder Links: RC4558
RC4558www.ti.com SLOS073G –MARCH 1976–REVISED OCTOBER 2014
11 Device and Documentation Support
11.1 TrademarksAll trademarks are the property of their respective owners.
11.2 Electrostatic Discharge CautionThis integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled withappropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be moresusceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.3 GlossarySLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
12 Mechanical, Packaging, and Orderable InformationThe following pages include mechanical packaging and orderable information. This information is the mostcurrent data available for the designated devices. This data is subject to change without notice and revision ofthis document. For browser based versions of this data sheet, refer to the left hand navigation.
Copyright © 1976–2014, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: RC4558
PACKAGE OPTION ADDENDUM
www.ti.com 14-Aug-2021
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead finish/Ball material
(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
RC4558D ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 RC4558
RC4558DE4 ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 RC4558
RC4558DGKR ACTIVE VSSOP DGK 8 2500 RoHS & Green NIPDAU | NIPDAUAG Level-1-260C-UNLIM 0 to 70 (YRP, YRS, YRU)
RC4558DGKRG4 ACTIVE VSSOP DGK 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 (YRP, YRS, YRU)
RC4558DR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM 0 to 70 RC4558
RC4558DRG3 ACTIVE SOIC D 8 2500 RoHS & Green SN Level-1-260C-UNLIM 0 to 70 RC4558
RC4558DRG4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 RC4558
RC4558ID ACTIVE SOIC D 8 75 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 R4558I
RC4558IDGKR ACTIVE VSSOP DGK 8 2500 RoHS & Green NIPDAU | NIPDAUAG Level-1-260C-UNLIM -40 to 85 (YSP, YSS, YSU)
RC4558IDGKRG4 ACTIVE VSSOP DGK 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 (YSP, YSS, YSU)
RC4558IDR ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 R4558I
RC4558IDRG4 ACTIVE SOIC D 8 2500 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 R4558I
RC4558IP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type -40 to 85 RC4558IP
RC4558IPW ACTIVE TSSOP PW 8 150 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 R4558I
RC4558IPWR ACTIVE TSSOP PW 8 2000 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 85 R4558I
RC4558P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 RC4558P
RC4558PE4 ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 RC4558P
RC4558PSR ACTIVE SO PS 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 R4558
RC4558PSRG4 ACTIVE SO PS 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 R4558
RC4558PW ACTIVE TSSOP PW 8 150 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 R4558
PACKAGE OPTION ADDENDUM
www.ti.com 14-Aug-2021
Addendum-Page 2
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead finish/Ball material
(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
RC4558PWR ACTIVE TSSOP PW 8 2000 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM 0 to 70 R4558
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substancedo not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI mayreference these types of products as "Pb-Free".RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide basedflame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to twolines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
RC4558DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
RC4558DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
RC4558DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
RC4558DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
RC4558DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
RC4558DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
RC4558DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
RC4558IDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
RC4558IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
RC4558IPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
RC4558IPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
RC4558PSR SO PS 8 2000 330.0 16.4 8.35 6.6 2.4 12.0 16.0 Q1
RC4558PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
RC4558PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jan-2022
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
RC4558DGKR VSSOP DGK 8 2500 364.0 364.0 27.0
RC4558DR SOIC D 8 2500 853.0 449.0 35.0
RC4558DR SOIC D 8 2500 340.5 336.1 25.0
RC4558DR SOIC D 8 2500 364.0 364.0 27.0
RC4558DRG3 SOIC D 8 2500 364.0 364.0 27.0
RC4558DRG4 SOIC D 8 2500 853.0 449.0 35.0
RC4558DRG4 SOIC D 8 2500 340.5 336.1 25.0
RC4558IDGKR VSSOP DGK 8 2500 364.0 364.0 27.0
RC4558IDR SOIC D 8 2500 340.5 336.1 25.0
RC4558IPWR TSSOP PW 8 2000 853.0 449.0 35.0
RC4558IPWR TSSOP PW 8 2000 364.0 364.0 27.0
RC4558PSR SO PS 8 2000 853.0 449.0 35.0
RC4558PWR TSSOP PW 8 2000 853.0 449.0 35.0
RC4558PWR TSSOP PW 8 2000 364.0 364.0 27.0
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jan-2022
Pack Materials-Page 2
TUBE
*All dimensions are nominal
Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
RC4558D D SOIC 8 75 507 8 3940 4.32
RC4558D D SOIC 8 75 506.6 8 3940 4.32
RC4558DE4 D SOIC 8 75 506.6 8 3940 4.32
RC4558DE4 D SOIC 8 75 507 8 3940 4.32
RC4558ID D SOIC 8 75 507 8 3940 4.32
RC4558IP P PDIP 8 50 506 13.97 11230 4.32
RC4558IPW PW TSSOP 8 150 530 10.2 3600 3.5
RC4558P P PDIP 8 50 506 13.97 11230 4.32
RC4558PE4 P PDIP 8 50 506 13.97 11230 4.32
RC4558PW PW TSSOP 8 150 530 10.2 3600 3.5
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jan-2022
Pack Materials-Page 3
www.ti.com
PACKAGE OUTLINE
C
.228-.244 TYP[5.80-6.19]
.069 MAX[1.75]
6X .050[1.27]
8X .012-.020 [0.31-0.51]
2X.150[3.81]
.005-.010 TYP[0.13-0.25]
0 - 8 .004-.010[0.11-0.25]
.010[0.25]
.016-.050[0.41-1.27]
4X (0 -15 )
A
.189-.197[4.81-5.00]
NOTE 3
B .150-.157[3.81-3.98]
NOTE 4
4X (0 -15 )
(.041)[1.04]
SOIC - 1.75 mm max heightD0008ASMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 [0.15] per side. 4. This dimension does not include interlead flash.5. Reference JEDEC registration MS-012, variation AA.
18
.010 [0.25] C A B
54
PIN 1 ID AREA
SEATING PLANE
.004 [0.1] C
SEE DETAIL A
DETAIL ATYPICAL
SCALE 2.800
www.ti.com
EXAMPLE BOARD LAYOUT
.0028 MAX[0.07]ALL AROUND
.0028 MIN[0.07]ALL AROUND
(.213)[5.4]
6X (.050 )[1.27]
8X (.061 )[1.55]
8X (.024)[0.6]
(R.002 ) TYP[0.05]
SOIC - 1.75 mm max heightD0008ASMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METALSOLDER MASKOPENING
NON SOLDER MASKDEFINED
SOLDER MASK DETAILS
EXPOSEDMETAL
OPENINGSOLDER MASK METAL UNDER
SOLDER MASK
SOLDER MASKDEFINED
EXPOSEDMETAL
LAND PATTERN EXAMPLEEXPOSED METAL SHOWN
SCALE:8X
SYMM
1
45
8
SEEDETAILS
SYMM
www.ti.com
EXAMPLE STENCIL DESIGN
8X (.061 )[1.55]
8X (.024)[0.6]
6X (.050 )[1.27]
(.213)[5.4]
(R.002 ) TYP[0.05]
SOIC - 1.75 mm max heightD0008ASMALL OUTLINE INTEGRATED CIRCUIT
4214825/C 02/2019
NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLEBASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
SYMM
SYMM
1
45
8
www.ti.com
PACKAGE OUTLINE
C
TYP6.66.2
1.2 MAX
6X 0.65
8X 0.300.19
2X1.95
0.150.05
(0.15) TYP
0 - 8
0.25GAGE PLANE
0.750.50
A
NOTE 3
3.12.9
BNOTE 4
4.54.3
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.5. Reference JEDEC registration MO-153, variation AA.
18
0.1 C A B
54
PIN 1 IDAREA
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL ATYPICAL
SCALE 2.800
www.ti.com
EXAMPLE BOARD LAYOUT
(5.8)
0.05 MAXALL AROUND
0.05 MINALL AROUND
8X (1.5)8X (0.45)
6X (0.65)
(R )TYP
0.05
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
SYMM
SYMM
LAND PATTERN EXAMPLESCALE:10X
1
45
8
NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METALSOLDER MASKOPENING
NON SOLDER MASKDEFINED
SOLDER MASK DETAILSNOT TO SCALE
SOLDER MASKOPENING
METAL UNDERSOLDER MASK
SOLDER MASKDEFINED
www.ti.com
EXAMPLE STENCIL DESIGN
(5.8)
6X (0.65)
8X (0.45)8X (1.5)
(R ) TYP0.05
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design.
SYMM
SYMM
1
45
8
SOLDER PASTE EXAMPLEBASED ON 0.125 mm THICK STENCIL
SCALE:10X
IMPORTANT NOTICE AND DISCLAIMERTI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements.These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2022, Texas Instruments Incorporated