quotation summary sheet

Nautilus Model 340BA-100 Marine Crane June 23, 2014

Quotation Summary Sheet

DATE: June 23, 2014

MACHINERY: API 2C MONOGRAMMED Pedestal Mounted Hydraulic Crane manufactured by

Oil States Skagit Smatco, LLC Nautilus Model 340BA-100 Marine Box Boom Crane as described in the attached proposal.


General Summarization 1. CRANE DESCRIPTION The quoted Nautilus Model 340BA-100 Marine Crane that has been in production for the past

fifteen years. The crane will be built to meet or exceed API Specification 2C (Spec. 2C), Seventh Edition, March 2012. This crane will bear the OFFICIAL API MONOGRAM and API SPEC. 2C NAMEPLATE mounted on a stainless steel placard.

Boom: The boom is a two piece double tapered box type constructed of high strength steel,

completely seal welded for complete corrosion protection. Welders are certified to AWS Specification D1.1 and 100% of all critical welds are NDE tested by certified third party NDE technicians. Our in-house inspectors are AWS (CWI) Certified Welding Inspectors.

Cylinder: The proposed crane is equipped with dual 12.5” diameter bore boom lift cylinders.

The retracted and extended lengths of the boom cylinders automatically limit the maximum and minimum boom angles and no boom stops and/or boom angle limit systems are required.

Rotation Bearing: Continuous 360° rotation using the finest quality rotation bearing. The

bearing mounting surfaces on the crane turret and pedestal flange are machined perfectly flat to provide maximum bearing life. All bolts are easily accessible from the outside of the pedestal.

2. CONFIGURATION The proposed crane is quoted as follows: · Nautilus Model 340 BA- 100 Marine Crane · Onboard Fully Enclosed Control Station · Onboard Rear Mounted Power Unit Assembly 3. TAPERED CRANE PEDESTAL A 4 ft – 3 in. overall high pedestal weldment is quoted and includes the following: · 3.00 in. thick flange for optimum support of the slewing bearing. · 80.00 in. Top O.D. x 60.00 in. Bottom tapered pedestal barrel with a 1.25 in. wall

thickness. · Large Rectangular Reinforced Manway (Manway has to be large enough for slipring assembly, slipring drawing to follow) Contact Oil States Skagit Smatco, LLC for applicable pedestal welding procedures before

welding. Improper welding procedures could cause damage to the flange, resulting in premature bearing failure.

Nominal 3,400,000 Ft. Lb. Rotation Bearing Moment Rating with Rated Load

100 Ft. Boom Box Boom

Nautilus Model 340BA-100 Marine Crane June 23, 2014 4

4. OPERATORS CONTROL STATION Crane operation will be from a fully enclosed operators’ control station located on the left side

of the crane rotating upperstructure. The control station will include the following: · Adjustable All Weather Vinyl Operator’s Seat · Hydraulic Pressure Gauges

Two (2) Dual Axis Pilot Controllers Swing Parking Brake Valve Motor Start/Stop Controls Sliding Windows for Cross Ventilation

. Emergency Load Lowering Kit . Manual Windshield Wipers Stainless steel, glycerin filled, hydraulic pressure gauges are featured to prevent frequent replacement due to corrosion or cracking experienced in less expensive "plastic" type gauges. A stainless steel load-rating chart will be attached to the operator's control station as well as

the official API 2C NAMEPLATE with API MONOGRAM. The etched stainless steel load-rating chart is inscribed in both boom angle and radius. A

corresponding stainless steel pendulum type angle indicator is attached to the boom in clear sight of the operator. The pendulum type boom angle indicator is predominantly used on cranes worldwide to measure the boom angles down to horizontal as required in API Specification 2C (Spec. 2C).

5. ELECTRIC MOTOR LOCATED ONBOARD THE CRANE ROTATING UPPERSTRUCTURE

Two (2) 150HP @ 1800 RPM Electric Motor 460VAC / 3 Phase / 60 Hertz / Class I, Div 2, Group D Two (2) Multiple Section Hydraulic Gear Pumps- one on each motor Stainless Steel Hydraulic Reservoir (¼" steel plate) Hydraulic Oil Cooler-Hydraulic driven motor/fan Hydraulic Tank Heater 5 Micron Hydraulic Oil Off-Line Filtration System with Water Removal Conoco Ecoterra 68 Hydraulic Oil Hydraulic Tanks include:

Level Gauge · Breather Vent · Positive Filler Screen Cap (UL approved and spring loaded) · Bolted and Gasketed Clean Out Access Hatches · Full perimeter Drip Pan in compliance with MMS requirements · Drain Outlet Connection with ball valves · Suction Strainers · Return Filter · Lifting Padeyes

Nautilus Model 340BA-100 Marine Crane June 23, 2014 6. SLEW BEARING, DRIVE AND BRAKING SYSTEMS An external gear ball bearing is standard on the Nautilus Model 340BA Marine Cranes in full

compliance with API. Dual planetary swing drive gearbox is quoted along with a replaceable pinion gear and slow

speed high torque hydraulic motor. A hydraulic swing lock (also called "Bear Claw" or "Storm Lock") is included to lock the crane

in position and is operated from the crane cab. Parking Brake – Spring applied, hydraulically released to “park” the crane in position. The

brake is automatically applied by the operator at the cab control console and is not deigned to stop a crane in motion.

The swing brake quoted is a fully enclosed hydraulic brake which is spring applied, hydraulically released to "park" the crane in position. This brake is manually applied by the operator and is not designed to stop a crane in motion.

Dynamic Brake – Spring released, hydraulically applied brake designed to stop a rotating crane via foot pedal at the operators’ control console. This “service brake” is in the same enclosure and is in addition to the parking brake.

7. MAIN HOIST/RIGGING (2 SPEED HOIST CIRCUIT)

A Braden Model CH400B-70144-02 is quoted to lift 85,200 lbs. (gross) at a minimum hook speed of 40 FPM in Low Speed and 60,000 lbs. (gross) at a minimum hook speed of 58 FPM in High Speed with the hook located at water level using four parts of .875-inch diameter Dyform-34 HSLR wire rope.

The hoist model number represents the following:

CH :

400 :

B :

70 :

144 :

02 :

1 :

Construction Hoist 40,000 pounds of line pull on the bottom layer at maximum pressure. Design Designation (no significance). 70:1 Planetary Gear Ratio. 14.4 Inch3/Rev. Hydraulic Motor Displacement (Commercial Intertech). Long Drum wire rope capacity. Hoist meets all requirements of API Spec. 2C and is rated for personnel handling.

A 70-Ton, dual sheave load block complete with swivel hook and safety latch is included to allow for four part line reeving along with 1,385 feet of wire rope.


8. AUX HOIST/RIGGING A Braden Model CH165A-25120-01-1 is quoted to lift 11,363 lbs (Gross) at a minimum hook

speed of 261 FPM using one parts of 3/4 in. diameter wire rope. The hoist model number represents the following:

CH :

165 :

A :

25 :

120 :

01 :

1 :

Construction Hoist 16,500 pounds of line pull on the bottom layer at maximum pressure. Design Designation (no significance). 25:1 Planetary Gear Ratio. 12.3 Inch3/Rev. Hydraulic Dual Motor Displacement (Commercial Intertech). Short drum wire rope capacity. Hoist meets all requirements of API Spec. 2C and is rated for personnel handling.

A 10-Ton, aux ball complete with swivel hook and safety latch is included to allow for one part

line reeving along with 440 feet of wire rope.

9. LOAD INDICATOR SYSTEM FOR THE MAIN AND AUXILIARY HOIST

The proposed crane is equipped with a Wylie Electronic Load Indicator System on the main and auxiliary hoist, which will serve as a visual tool to the crane operator. This load indicator system will be calibrated and properly sized for the proper wire rope and a 100 ft. boom. The indicator gauge will be mounted on the operator's control station.

10. ANTI-TWO BLOCKING DEVICE The crane will be equipped with a stainless steel non-overrideable model CBSD anti-two block

valve assembly for the main system that is a fully fail-safe anti-two blocking system.

This CBSD system is constructed of stainless steel to prevent corrosion. This system will preclude the traveling load block from coming into contact with the sheave case regardless of the accumulation of wire rope lubrication.


11. ELECTRICAL SYSTEM

The proposed crane is provided with the following Electrical System suitable for Class I,

Div. 2, Group D area classification. (1) One Beacon Light on Boom Tip (1) One Beacon Light on Rear of Crane (2) Two LED Boom Flood Lights from Dialight (1) One 60 Watt Cabin Light Attention Horn A/C Main three pole circuit breaker for tank heater, air conditioner and crane light system Instrument Lights Motor Start / Stop Control in Cabin (2) Two 150 HP Electric Motors (2) Two Motor Starters – Soft Start Orlaco Boom Tip Camera with Monitor in Cabin Wylie 650 V3 Load Indicator for Main and Aux. Hydraulic Tank Heater Hydraulic Oil Off-Line Filtration System with Water Removal Switches, Wiring, Mounting Brackets, etc. Platform Supplied Power: 460VAC, 60 Hz, 3 Phase for motors- One feed for each

motor to allow crane to operate on one motor Crane lighting system power to be obtained from separate 460VAC platform supply-

transformer Platform will supply separate power for aircraft warning lights from emergency

generator- voltage to be confirmed with approval drawings Slipring assembly to have (8) rings for motor power, (3) rings for light system power, (3)

rings for aircraft warning light power and (17) silver plated communication rings Customer will connect to slipring routing cables in center of pedestal- no external

pedestal junction boxes required. Camera and Wylie specs supplied by Noble and cannot be changed All cable glands to ground to armor of shipboard cable All junction boxes to be NEMA 4X stainless steel Customer will supply Gaitronics system and wire to slipring

Please note that platform supplied power will be required! 460 VAC, 3 Phase, 60 Hertz for motor power 120 VAC, 1 Phase, 60 Hertz for crane light system power

12. CORROSION PROTECTION

The Protective Corrosion and Paint System for the proposed crane will be a four (4) coat International Paint System

All structural hinge pins will be constructed of stainless steel material to provide for ultimate

corrosion protection.


13. FUNCTIONAL TESTING The proposed crane will be completely assembled and functionally load tested (Rated Load)

at the Oil States Skagit Smatco, LLC, Manufacturing Facility in Houma, Louisiana, prior to shipment.

14. MAINTENANCE, OPERATION AND PARTS MANUALS Included in this quotation are three (3) English and (3) Spanish Operations, Maintenance, and

Parts Manuals. These manuals are extremely detailed and feature hose lists and other critical data. All documents created by OSI will be in English and Spanish language. Manuals for major components come directly from the supplier; therefore, OSI will request the manuals in English and Spanish if they are available.

15. INSTALLATION Oil States Skagit Smatco, LLC has not included any installation charges in the base crane

price. Any installation assistance required will be invoiced in accordance with the Oil States Skagit Smatco, LLC Standard Field Service Rate Schedule.

16. WARRANTY

The Oil States Skagit Smatco, LLC warranty included in this quotation will supersede all other warranty provisions for the crane.

17. MISCELLANEOUS

Emergency Load Lowering Kit Stainless Steel Pin Kit Hydraulic Anti-Two Block for Main and Aux Hoist Stainless Steel Hydraulic Tank Maintenance Jib- Distance from Rig deck to highest part of crane cannot exceed 32 Ft

as this is the elevation of the helideck. Two Piece Box Boom Full Boom Walkway with Tip Access Stainless Steel Bolts for all Bolts Under ¾” Block Parking Mechanism for Load Block and Aux. Ball Fleet Angle Idler for Auxiliary Hoist Terresolve EnviroLogic 68- Engineering to verify this oil is acceptable to all component

manufacturers


Main Hoist Lift Capacity Chart Nautilus Model 340BA-100 Marine Crane

WIRE ROPE: Four Part .875” Dyform-34 HSLR HOIST: Braden Model CH280A-54144-02

RADIUS

(FT)

ANGLE

(DEG)

ONBOARD OFFBOARD Cb=2.0

LOW

SPEED

(LB)

HIGH

SPEED

(LB)

LOW

SPEED

(LB)

HIGH

SPEED

(LB)

11 83 84,000 58,800 78,757 58,800

15 81 84,000 58,800 71,687 58,800

20 78 84,000 58,800 65,788 58,800

25 75 84,000 58,800 60,836 58,800

30 72 84,000 58,800 56,640 56,640

35 69 81,996 58,800 53,052 53,052

40 67 75,665 58,800 49,170 49,170

45 63 67,138 58,800 43,815 43,815

50 60 60,188 58,800 39,403 39,403

55 57 54,369 54,369 35,677 35,677

60 53 49,379 49,379 32,456 32,456

65 50 45,101 45,101 29,609 29,609

70 46 41,203 41,203 27,033 27,033

75 42 37,576 37,576 24,639 24,639

80 37 34,086 34,086 22,339 22,339

85 32 30,570 30,570 20,028 20,028

90 26 26,763 26,763 17,533 17,533

95 19 22,025 22,025 14,443 14,443

100 1 9,673 9,673 6,737 6,737

All ratings are in accordance with "API 2C, Seventh Edition. Ratings are applicable for a crane on a Fixed Platform using the Dynamic Default Method

The above ratings are "net" ratings, as the load block weight of 1,200 lbs. has been subtracted to determine the "net" lifting capacity.


Main Hoist Performance Chart Nautilus Model 340BA-100 Marine Crane

Braden Model CH280A-54144-02

.875” Diameter Dyform-34 HSLR Wire Rope

LAYER

ROPE

CAPACITY

(FT)

HIGH SPEED - 4 PART REEVING LOW SPEED - 4 PART REEVING

LINE

PULL

(LBS)

SINGLE

LINE PULL

PRESSURE

(PSI)

LINE

SPEED

(FPM)

HOOK

PERF

(LBS)

HOOK

SPEED

(FPM)

LINE

PULL

(LBS)

SINGLE

LINE PULL

PRESSURE

(PSI)

LINE

SPEED

(FPM)

HOOK

PERF

(LBS)

HOOK

SPEED

(FPM)

1 217 Not Used · Remains on Drum 2 452 15,748 1,382 231 60,000 58 22,362 1,963 159 85,200 40

3 705 15,748 1,476 246 60,000 62 22,362 2,096 170 85,200 42

*4 974 15,748 1,569 262 60,000 65 22,362 2,229 181 85,200 45

5 1,262 Storage Layer Storage Layer 6 1,566 Storage Layer Storage Layer 7 1,889 Storage Layer Storage Layer 8 2,228 Storage Layer Storage Layer

NOTES: 1. Above High Speed performance values are based on 192.6 GPM 2. Above Low Speed performance values are based on 139.2 GPM

3. 250 feet of hook travel is available (on location). 4. Total wire rope capacity consists of four parts of line with 250 feet hook travel + 5%

reeving allowance + 100 feet boom length + 217 feet remaining on hoist drum at all times = 1,385 feet total.

5. Sheave Efficiencies are considered in above values. *6. Top layer required for four part line reeving with 250 feet of hook travel with 217 feet

remaining on the hoist drum at all times. 7. Calculation for hoist limitation with four part reeving: Full Drum Line Pull X Effective Number of Line Parts 15,748 lbs. X 3.81 = 60,000 lbs. Lifting Capacity – High Speed 22,362 lbs. X 3.81 = 85,200 lbs. Lifting Capacity – Low Speed 8. Minimum hook speed available is 40 FPM with the hook at water level for Low speed and

58 FPM for High Speed.


Auxiliary Hoist Lift Capacity Chart

Nautilus Model 340BA-100 Marine Crane

WIRE ROPE: One Part 3/4” Dyform-34 HOIST: Braden Model CH165A-25120-01-1

RADIUS (FT)

ANGLE (DEG)

RATED

ONBOARD LOAD (LBS)

RATED OFFBOARD LOAD

(Cv = 1.4) (LBS)

13 83.4 10,936 10,936

15 82.6 10,936 10,936

20 79.8 10,936 10,936

25 77.0 10,936 10,936

30 74.1 10,936 10,936

35 71.2 10,936 10,936

40 68.3 10,936 10,936

45 65.3 10,936 10,936

50 62.2 10,936 10,936

55 59.0 10,936 10,936

60 55.6 10,936 10,936

65 52.2 10,936 10,936

70 48.5 10,936 10,936

75 44.6 10,936 10,936

80 40.4 10,936 10,936

85 35.8 10,936 10,936

90 30.5 10,936 10,936

95 24.0 10,936 10,936

100 14.9 10,936 10,936

103 2.1 10,936 8,790

All ratings are in accordance with "API 2C, Seventh Edition. Ratings are applicable for a crane on a Fixed Platform using the Dynamic Default Method

The above ratings are "net" ratings, as the load block weight of 200 lbs. has been subtracted to determine the "net" lifting capacity.


Auxiliary Hoist Performance Chart


Braden Model CH165A-25120-01-1

3/4” Diameter Dyform-34 Wire Rope

LAYER

ROPE

CAPACITY

(FT)

LINE PULL

SINGLE LINE

(LBS)

SINGLE LINE

PULL

PRESSURE

(PSI)

LINE SPEED

SINGLE LINE

(FPM)

HOOK

PERFORMANCE

1 PART LINE

(LBS)

HOOK SPEED

1 PART LINE

(FPM)

1 78 Not Used · Remains on Drum 2 163 11,363 2,202 261 11,136 261

3 256 11,363 2,395 284 11,136 284

*4 356 11,363 2,588 307 11,136 307

5 464 Storage Layer 6 579 Storage Layer 7 701 Storage Layer

NOTES: 1. Above performance values are based on 99.8 GPM 2. 250 feet of hook travel is available (on location). 3. Total wire rope capacity consists of one part of line with 250 feet hook travel + 5% reeving

allowance + 100 feet boom length + 78 feet remaining on hoist drum at all times =440 feet total.

4. Sheave Efficiencies are considered in above values. *5. Top layer required for one part line reeving with 250 feet of hook travel with 78 feet remaining

on the hoist drum at all times. 6. Calculation for hoist limitation with one part reeving: Full Drum Line Pull X Effective Number of Line Parts

11,363 lbs. X .98 = 11,136 lbs. Lifting Capacity

7. Minimum hook speed available is 261 FPM with the hook at the water level.


Installation Parameters


API Spec. 2C

Pedestal Reactions

Pedestal In-Plane

Moment (ft×lbf)

Pedestal Side

Moment (ft×lbf)

Pedestal Axial Compression

(lbf)

Pedestal Torque (ft×lbf)

Pedestal In-Plane Radial Load (lbf)

Pedestal Side Plane

Radial Load (lbf)

Maximum Moment

7,133,090 131,339 163,429 119,848 29 1,723

Maximum Axial 2,438,350 502,964 313,990 47,600 64 4,760

PF x Cv x SWLH

(ABOVE REACTIONS ARE AS PER API 2C 7th Edition)

Nautilus Model 340BA-100 Marine Crane February 27, 2014

· OSSS’ LIMITED WARRANTY ·

I. PRODUCTS LIMITED WARRANTY: A. Subject to the limitations hereafter set forth, OSSS warrants that all assembled “Products” and parts shall be free from defects in design, materials and workmanship, comply with any applicable scope of work document, and conform to OSSS’ published specifications for a period of 12 months after installation, but not later than 18 months after factory acceptance testing (FAT) at the OSSS Plant, Houma, LA whichever occurs first. For refurbished Products or exchanged Products or electrical parts or components, the warranty period expires one hundred eighty (180) days from the date of FAT or from the date of shipment, whichever occurs first. OSSS does not warrant that its Products will accomplish any particular result. For any Product containing a prime mover supplied by a third party supplier, OSSS’ liability shall be limited to the assignment of such third party supplier’s warranty to the Customer (as hereinafter defined). OSSS shall have no responsibility or liability for any Customer furnished materials. B. The exclusive remedy provided by OSSS within the warranty period specified in paragraph “A” shall be, at the option of OSSS, either the repair or replacement of any part or Product found by OSSS to be defective or a credit for any part or Products, subject to the following terms and conditions:

1) Complete parts or Products must be returned to OSSS within the warranty period, transportation charges prepaid or if not practical, OSSS will send an authorized field service representative at the customer’s expense to the site for repair or replacement. 2) This warranty is void, if, in the opinion of OSSS, the failure of the part or Product resulted from abuse or neglect or where such failure has been caused by accident. 3) This warranty is void unless installation and start-up has been supervised by an OSSS authorized field service representative. 4) Additional costs or expenses such as assistance labor, rental equipment, boats, cranes, or helicopters incurred by the Customer for removal, reinstallation and repair of OSSS parts or Products is not covered by this warranty and the Customer assumes full responsibility for such costs and charges. OSSS will cover all OSSS supplied labor required to remove, repair, and/or replace the defective part or system only. All other expenses such as airfare, hotel, meals, stand-by and travel time are to be charged to the Customer’s account. 5) This warranty is void unless the Customer or its agents provide proper transportation and storage facilities and reasonable care of the complete Product or part from the date of delivery until the date placed in service. 6) The warranty is void if any modifications are made to any part or Product without the prior written consent of OSSS.


7) Also excluded from the warranty are any costs of non-warranty repairs or modifications to the Product made by parties other than OSSS, any costs related to consumable components of the equipment or Product (including, but not restricted to, hydraulic fluid, filters and strainers, lubricants, wiper blades, light bulbs, wire rope, fuel, and drive belts), and any costs related to repairs or replacement as the result of damage to Product that arise from normal component wear and tear, from accidents that were not caused by OSSS or its agents, or from force majeure.

C. Only authorized factory representatives of OSSS shall have authority to assume any cost or expense in the service, repair or replacement of any part or Product within the warranty period except when such cost or expense is authorized in advance in writing by OSSS. D. OSSS does not warrant or accept responsibility for any work performed by third party contractors hired by the Customer or a purchaser, owner, or shipyard on OSSS furnished equipment unless OSSS directly supervises the work and accepts said arrangement in writing before work commences. In the event any work has started or been completed before the agreement between the parties is in place, OSSS is to be held harmless of any loss or damages resulting from said work. E. OSSS reserves the right to improve the Product through changes in design or material without being obligated to incorporate such changes in Products of prior manufacture. Customer agrees not to rely on any such changes as proof of inadequacy or defect in prior designs or material. F. This Warranty is valid from the effective date as provided in paragraph A above and is not made null and void by new warranty policies issued at any future date. This Warranty covers only Products manufactured and delivered by OSSS during the time frame that this Warranty is in effect. G. OSSS’ warranty obligations shall not begin until OSSS has been paid the contract price in full. OSSS’ warranty obligations shall terminate if a) Customer fails to perform its obligations under this or any other Agreement between the parties, or b) if Customer fails to pay any amounts owed to OSSS. H. The term “Customer” as used throughout this Warranty shall apply to the purchaser of the Products covered by this warranty. In the event that the Customer should purchase Product on behalf of, or for the intended delivery to, a third party, then this Warranty, its provisions, and conditions, shall be transferable to said third party owner with the understanding that the warranty period shall continue in force as expressly stated above, without extension of time, unless otherwise extended by an authorized representative by OSSS in writing to the third party owner. THE PARTIES AGREE THAT ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, OF WORKMANLIKE PERFORMANCE AND/OR FOR REDHIBITORY DEFECTS, ARE DISCLAIMED AND EXCLUDED. THE REMEDIES SET OUT ABOVE ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY BY OSSS.


II. SERVICES LIMITED WARRANTY:

OSSS will not be liable for concealed and unusual conditions at the work site, either above or underground, where such conditions were not reasonably discoverable through normal visual inspection, where such conditions were not indicated by Customer, or where Customer has supplied inadequate or incomplete information. In the event such concealed or unusual conditions result in delays and extra expense to OSSS, an equitable adjustment shall be made in the contract price and schedule. Furthermore, OSSS reserves the right not to perform work if, in its opinion, job conditions render such action inadvisable. The warranties offered by OSSS are expressly limited to the following: OSSS warrants that services and repairs provided pursuant to the agreement with Customer shall be free from defects in workmanship and materials, comply with the applicable scope of work document, conform to OSSS’ published specifications and shall otherwise be supplied in accordance with sound and generally accepted industry practice by competent personnel for a period of ninety (90) days from the date of service or repair. This warranty is exclusive of any other liability, particularly in respect of any damage suffered because of defective services or repairs. In the event that OSSS’ services or repairs fail to comply with the foregoing standards, OSSS shall perform such corrective services or repairs of the type originally performed. Liability will only be accepted if the service or repair concerned was used for the purpose for which it was designed. OSSS shall have no responsibility with regard to materials furnished by third-party suppliers used or provided in connection with such services, OSSS’ liability for materials furnished by its third-party suppliers shall be limited to the assignment of such third-party supplier’s warranty, if any, to Customer. OSSS shall have no responsibility or liability for any Customer furnished materials. THE PARTIES AGREE THAT ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, OF WORKMANLIKE PERFORMANCE AND/OR FOR REDHIBITORY DEFECTS, ARE DISCLAIMED AND EXCLUDED. THE REMEDIES SET OUT ABOVE ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY BY OSSS.

quotation summary sheet

Documents