question paper solution unit- 1: antenna basics · pdf file · 2013-10-24antennas...
TRANSCRIPT
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 1
QUESTION PAPER SOLUTION
Unit- 1: Antenna Basics
1. Explain Radiation pattern (june/july08)
A radiation pattern defines the variation of the power radiated by an antenna as a function of
the direction away from the antenna. This power variation as a function of the arrival angle is
observed in the far field.
This is an example of a donut shaped or toroidal pattern. In this case, along the z-axis, which
would correspond to the radiation directly overhead the antenna, there is very little power
transmitted. In the x-y plane (perpendicular to the z-axis), the radiation is maximum. These
plots are useful for visualizing which directions the antenna radiates.
2. Explain Field Regions(june/july07)
A pattern is "isotropic" if the radiation pattern is the same in all directions. These antennas
don't exist in practice, but are sometimes discussed as a means of comparison with real
antennas. Some antennas may also be described as "omnidirectional", which for an actual
means that it is isotropic in a single plane (as in Figure 1 above for the x-y plane). The third
category of antennas are "directional", which do not have a symmetry in the radiation pattern.
The far field region is the most important, as this determines the antenna's radiation pattern.
Also, antennas are used to communicate wirelessly from long distances, so this is the region
of operation for most antennas. We will start with this region.
Far Field (Fraunhofer) Region
The far field is the region far from the antenna, as you might suspect. In this region, the
radiation pattern does not change shape with distance (although the fields still die off with
1/R^2). Also, this region is dominated by radiated fields, with the E- and H-fields orthogonal
to each other and the direction of propagation as with plane waves.
If the maximum linear dimension of an antenna is D, then the far field region is commonly
given as:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 2
This region is sometimes referred to as the Fraunhofer region, a carryover term from optics.
In the immediate vicinity of the antenna, we have the reactive near field. In this region, the
fields are predominately reactive fields, which means the E- and H- fields are out of phase by
90 degrees to each other (recall that for propagating or radiating fields, the fields are
orthogonal (perpendicular) but are in phase).
The boundary of this region is commonly given as:
Radiating Near Field (Fresnel) Region
The radiating near field or Fresnel region is the region between the near and far fields. In this
region, the reactive fields are not dominate; the radiating fields begin to emerge. However,
unlike the Far Field region, here the shape of the radiation pattern may vary appreciably with
distance.
The region is commonly given by:
Note that depending on the values of R and the wavelength, this field may or may not exist.
Finally, the above can be summarized via the following diagram:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 3
3. Explain DIRECTIVITY(june/july07)
Directivity is a fundamental antenna parameter. It is a measure of how 'directional' an
antenna's radiation pattern is. An antenna that radiates equally in all directions would have
effectively zero directionality, and the directivity of this type of antenna would be 1 (or 0
dB).
An antenna's normalized radiation pattern can be written as a function in spherical
coordinates:
Because the radiation pattern is normalized, the peak value of F over the entire range of
angles is 1. Mathematically, the formula for directivity (D) is written as:
This equation might look complicated, but the numerator is the maximum value of F, and the
denominator just represents the "average power radiated over all directions". This equation
then is just a measure of the peak value of radiated power divided by the average.
4. Explain EFFICIENCY AND GAIN (june/july09)
The efficiency of an antenna relates the power delivered to the antenna and the power
radiated or dissipated within the antenna. A high efficiency antenna has most of the power
present at the antenna's input radiated away. A low efficiency antenna has most of the power
absorbed as losses within the antenna.
The losses associated within an antena are typically the conduction losses (due to finite
conductivity of the antenna) and dielectric losses (due to conduction within a dielectric which
may be present within an antenna). Sometimes efficiency is defined to also include the
mismatch between an antenna and the transmission line, but this will be discussed in the
section on impedance.
The efficiency can be written as the ratio of the radiated power to the input power of the
antenna:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 4
The term Gain describes how much power is transmitted in the direction of peak radiation to
that of an isotropic source. Gain is more commonly quoted in a real antenna's specification
sheet because it takes into account the actual losses that occur.
A gain of 3 dB means that the power received far from the antenna will be 3 dB (twice as
much) higher than what would be received from a lossless isotropic antenna with the same
input power.
Gain is sometimes discussed as a function of angle, but when a single number is quoted the
gain is the 'peak gain' over all directions. Gain (G) can be related to directivity (D) by:
The gain of a real antenna can be as high as 40-50 dB for very large dish antennas (although
this is rare). Directivity can be as low as 1.76 dB for a real antenna, but can never
theoretically be less than 0 dB. However the peak gain of an antenna can be arbitrarily low
because of losses. Electrically small antennas (small relative to the wavelength of the
frequency that the antenna operates at) can be very inefficient, with gains lower than -10 dB
(even without accounting for impedance mismatch loss).
5. Explain BEAM WIDTH AND SIDE LOBES: (june/july07)
The main beam is the region around the direction of maximum radiation (usually the region
that is within 3 dB of the peak of the main beam). The main beam in Figure 6 is centered at
90 degrees.
The sidelobes are smaller beams that are away from the main beam. These sidelobes are
usually radiation in undesired directions which can never be completely eliminated. The
sidelobes in Figure 6 occur at roughly 45 and 135 degrees.
The Half Power Beamwidth (HPBW) is the angular separation in which the magnitude of
the radiation pattern decrease by 50% (or -3 dB) from the peak of the main beam. From
Figure 2, the pattern decreases to -3 dB at 77.7 and 102.3 degrees. Hence the HPBW is 102.3-
77.7 = 24.6 degrees.
Another commonly quoted beamwidth is the Null to Null Beamwidth. This is the angular
separation from which the magnitude of the radiation pattern decreases to zero (negative
infinity dB) away from the main beam. From Figure 2, the pattern goes to zero (or minus
infinity) at 60 degrees and 120 degrees. Hence, the Null-Null Beamwidth is 120-60=60
degrees.
Finally, the Sidelobe Level is another important parameter used to characterize radiation
patterns. The sidelobe level is the maximum value of the sidelobes (away from the main
beam). From Figure 6, the Sidelobe Level (SLL) is -14.5 dB.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 5
6. Explain Antenna's impedance(Dec/Jan 07)
An antenna's impedance relates the voltage to the current at the input to the antenna. Letan
antenna has an impedance of 50 ohms. This means that if a sinusoidal voltage is input at the
antenna terminals with amplitude 1 Volt, the current will have an amplitude of 1/50 = 0.02
Amps. Since the impedance is a real number, the voltage is in-phase with the current.
Let's say the impedance is given as Z=50 + j*50 ohms (where j is the square root of -1). Then
the impedance has a magnitude of
and a phase given by
This means the phase of the current will lag the voltage by 45 degrees. To spell it out, if the
voltage (with frequency f) at the antenna terminals is given by
then the current will be given by
So impedance is a simple concept, which relates the voltage and current at the input to the
antenna. The real part of an antenna's impedance represents power that is either radiated away
or absorbed within the antenna. The imaginary part of the impedance represents power that is
stored in the near field of the antenna (non-radiated power). An antenna with a real input
impedance (zero imaginary part) is said to be resonant.
7. Explain BANDWIDTH(june/july07)
Bandwidth describes the range of frequencies over which the antenna can properly radiate or
receive energy. Often, the desired bandwidth is one of the determining parameters used to
decide upon an antenna. For instance, many antenna types have very narrow bandwidths and
cannot be used for wideband operation.
Bandwidth is typically quoted in terms of VSWR. For instance, an antenna may be described
as operating at 100-400 MHz with a VSWR<1.5. This statement implies that the reflection
coefficient is less than 0.2 across the quoted frequency range. Hence, of the power delivered
to the antenna, only 4% of the power is reflected back to the transmitter. Alternatively, the
return loss S11=20*log10(0.2)=-13.98 dB.
8. Explain Polarization (Dec/Jan 08)
Polarization is a fundamental characteristics of any antenna.
Linear Polarization
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 6
A plane electromagnetic (EM) wave is characterized by travelling in a single direction (with
no field variation in the two orthogonal directions). In this case, the electric field and the
magnetic field are perpendicular to each other and to the direction the plane wave is
propagating. As an example, consider the single frequency E-field given by equation (1),
where the field is traveling in the +z-direction, the E-field is oriented in the +x-direction, and
the magnetic field is in the +y-direction.
In equation (1), the symbol is a unit vector (a vector with a length of one), which says that
the E-field "points" in the x-direction.
9. Explain ANTENNA TEMPERATURE
Antenna Temperature ( ) is a parameter that describes how much noise an antenna
produces in a given environment. This temperature is not the physical temperature of the
antenna. Moreover, an antenna does not have an intrinsic "antenna temperature" associated
with it; rather the temperature depends on its gain pattern and the thermal environment that it
is placed in.
For an antenna with a radiation pattern given by , the noise temperature is
mathematically defined as:
10. Explain EFFECTIVE APERTURE(june/july09)
A useful parameter calculating the receive power of an antenna is the effective area or
effective aperture. Assume that a plane wave with the same polarization as the receive
antenna is incident upon the antenna.
Then the effective aperture parameter describes how much power is captured from a given
plane wave. Let W be the power density of the plane wave (in W/m^2). If P represents the
power at the antennas terminals available to the antenna's receiver, then:
Hence, the effective area simply represents how much power is captured from the plane wave
and delivered by the antenna. This area factors in the losses intrinsic to the antenna (ohmic
losses, dielectric losses, etc.). This parameter can be determine by measurement for real
antennas.
A general relation for the effective aperture in terms of the peak gain (G) of any antenna is
given by:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 7
Effective aperture will be a useful concept for calculating received power from a plane wave.
To see this in action, go to the next section on the Friis transmission formula.
11. Explain FRIIS transmission formula(Dec08/jan09)
Consider two antennas in free space (no obstructions nearby) separated by a distance R:
Assume that Watts of total power are delivered to the transmit antenna. For the moment,
assume that the transmit antenna is omnidirectional, lossless, and that the receive antenna is
in the far field of the transmit antenna. Then the power p of the plane wave incident on the
receive antenna a distance R from the transmit antenna is given by:
If the transmit antenna has a gain in the direction of the receive antenna given by , then
the power equation above becomes:
The gain term factors in the directionality and losses of a real antenna. Assume now that the
receive antenna has an effective aperture given by . Then the power received by this
antenna ( ) is given by:
Since the effective aperture for any antenna can also be expressed as:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 8
The resulting received power can be written as:
This is known as the Friis Transmission Formula. It relates the free space path loss, antenna
gains and wavelength to the received and transmit powers. This is one of the fundamental
equations in antenna theory, and should be remembered (as well as the derivation above).
12. Explain Reciprocity (Dec07/jan08)
An antenna’s electrical characteristics are the same whether it is used for transmitting or
receiving. Because this is always true, throughout this lecture, we will consider antennas as
transmitting antennas.
13. Explain Polarization(Dec07/jan08)
Polarization is the orientation of the electric field vector of the electromagnetic wave
produced by the antenna. For most antennas, the orientation of the antenna conductor
determines the polarization. Polarization may be vertical, horizontal or elliptical.
The diagram above shows vertical and horizontal polarization. If the radio wave's electric
field vector points in some other direction, it is said to be obliquely polarized.
If the electric field rotates in space, such that its tip follows an elliptical path, it is elliptically
polarized.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 9
14. Explain Wavelength (Dec07/jan08)
This is the length of one RF wave. It can be computed by either of the following formulas,
depending on the units required:
(in m) = 300/f(in MHz) or (in ft) = 984/f(in MHz)
Unit- 2: Point Sources and Arrays
1. Explain Isotropic radiator (june/july08)
An isotropic radiator is a theoretical point source of waves which exhibits the same
magnitude or properties when measured in all directions. It has no preferred direction of
radiation. It radiates uniformly in all directions over a sphere centred on the source. It is a
reference radiator with which other sources are compared. Isotropic radiators obey Lambert's
law.
2. Explain ANTENNA ARRAYS (Dec 08/Jna09)
An antenna array (often called a 'phased array') is a set of 2 or more antennas. The signals
from the antennas are combined or processed in order to achieve improved performance over
that of a single antenna. The antenna array can be used to:
increase the overall gain
provide diversity reception
cancel out interference from a particular set of directions
"steer" the array so that it is most sensitive in a particular direction
determine the direction of arrival of the incoming signals
to maximize the Signal to Interference Plus Noise Ratio (SINR)
An antenna array is an antenna that is composed of more than one conductor. There are two
types of antenna arrays:
Driven arrays – all elements in the antenna are fed RF from the transmitter
Parasitic arrays – only one element is connected to the transmitter. The other elements are
coupled to the driven element through the electric fields and magnetic fields that exist in the
near field region of the driven element
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 10
3. Explain COLLINEAR ARRAY( Dec 07/jan 08)
The collinear array consists of /2 dipoles oriented end-to-end. The center dipole is fed by the
transmitter and sections of shorted transmission line known as phasing lines connect the ends
of the dipoles as shown below.
The length of the phasing lines are adjusted so that the currents in all the dipole sections are
in phase, as shown below.
The input impedance of a collinear array is approximately 300 ohms. The directivity of a
collinear array slowly increases as the number of collinear sections is increased.
4. Explain BROADSIDE ARRAY (june/july08)
A broadside array consists of an array of dipoles mounted one above another as shown below.
Each dipole has its own feed line and the lengths of all feed lines are equal so that the
currents in all the dipoles are in phase.
Rows of broadside arrays can be combined to form a two dimensional array as shown below:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 11
The two-dimensional array is used in high performance radar systems. The amplitude and
phase of each input current is adjusted so that the antenna radiates its RF in a narrow beam.
By making changes to the input phase and amplitude, the beam can be made to scan over a
wide range of angles. Electronic scanning is much faster than mechanical scanning (which
uses a rotating antenna) and permits rapid tracking of large numbers of targets.
A special type of phased array consisting of 2 or more vertical antennas is widely used in
AM broadcasting. Consider an AM transmitter located in a coastal city such as Charleston,
SC. It would make no sense to radiate a signal in all directions; there is only water to the east
of city. Two or more antennas could be used to produce a directional pattern that would
radiate most of the signal to the west.
The design and analysis of phased arrays is quite difficult and will not be covered further in
this unit.
Unit- 3: Electric Dipoles and Thin Linear Antennas
1. Write a note on short dipole antenna and describe the fields of short dipole
antenna(june/july07)
The short dipole antenna is the simplest of all antennas. It is simply an open-circuited wire,
fed at its center as shown in Figure 1.
The words "short" or "small" in antenna engineering always imply "relative to a wavelength".
So the absolute size of the above dipole does not matter, only the size of the wire relative to
the wavelength of the frequency of operation. Typically, a dipole is short if its length is less
than a tenth of a wavelength:
If the antenna is oriented along the z-axis with the center of the dipole at z=0, then the current
distribution on a thin, short dipole is given by:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 12
The fields radiated from this antenna in the far field are given by:
2. Explain the fields of thin linear antenna (june/july08)
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 13
Unit- 4: Loop, Slot, Patch and Horn Antenna
1. Describe LOOP ANTENNAS (june/july10)
All antennas discussed so far have used radiating elements that were linear conductors. It is
also possible to make antennas from conductors formed into closed loops. There are two
broad categories of loop antennas:
1. Small loops, which contain no more than 0.085 wavelengths (~/12) of wire
2. Large loops, which contain approximately 1 wavelength of wire.
SMALL LOOP ANTENNAS
A small loop antenna is one whose circumference contains no more than 0.085 wavelengths
of wire. In such a short conductor, we may consider the current, at any moment in time to be
constant. This is quite different from a dipole, whose current was a maximum at the feed
point and zero at the ends of the antenna. The small loop antenna can consist of a single turn
loop or a multi-turn loop as shown below:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 14
2. Explain the radiation pattern of small loop antenna
The radiation pattern of a small loop is very similar to a dipole. The figure below shows a 2-
dimensional slice of the radiation pattern in a plane perpendicular to the plane of the loop.
There is no radiation from a loop
3. Explain slot antenna (june/july10)
A slot antenna consists of a metal surface, usually a flat plate, with a hole or slot cut out.
When the plate is driven as an antenna by a driving frequency, the slot radiates
electromagnetic waves in similar way to a dipole antenna. The shape and size of the slot, as
well as the driving frequency, determine the radiation distribution pattern. Slot antennas are
often used instead of line antennas when greater control of the radiation pattern is required.
Slot antennas are often found in standard desktop microwave sources used for research
purposes.
A slot antenna's main advantages are its size, design simplicity, robustness, and convenient
adaptation to mass production using PC board technology.
Slot antennas are used typically at frequencies between 300 MHz and 24 GHz. These
antennas are popular because they can be cut out of whatever surface they are to be mounted
on, and have radiation patterns that are roughly omnidirectional (similar to a linear wire
antenna, as we'll see). The polarization is linear. The slot size, shape and what is behind it
(the cavity) offer design variables that can be used to tune performance.
4. Explain Babinets principle (June/July09)
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 15
Babinet's principle relates two antennas. The first result states that the impedance of the slot
( ) is related to the impedance of its dual antenna ( ) by the relation:
In the above, is the intrinsic impedance of free space. The second major result of
Babinet's/Booker's principle is that the fields of the dual antenna are almost the same as the
slot antenna (the fields components are interchanged, and called "duals"). That is, the fields
of the slot antenna (given with a subscript S) are related to the fields of it's complement
(given with a subscript C) by:
Hence, if we know the fields from one antenna we know the fields of the other antenna.
Hence, since it is easy to visualize the fields from a dipole antenna, the fields and impedance
from a slot antenna can become intuitive if Babinet's principle is understood.
Note that the polarization of the two antennas are reversed. That is, since the dipole antenna
on the right in Figure 2 is vertically polarized, the slot antenna on the left will be horizontally
polarized.
5. Explin Horn antenna (june/july10)
A horn antenna is used for the transmission and reception of microwave signals. It derives its
namefrom the characteristic flared appearance. The flared portion can be square, rectangular,
or conical. The maximum radiation and responsecorresponds with the axis of the horn. In this
respect, the antenna resembles anacoustic horn. It is usually fed with a waveguide.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 16
In order to function properly, a horn antenna must be a certain minimum size relativeto the
wavelength of the incoming or outgoing electromagnetic field. If the horn istoo small or the
wavelength is too large (the frequency is too low), the antenna will not work efficiently.
Horn antennas are commonly used as the active element in a dish antenna. The horn is
pointed toward the centerof the dish reflector. The use of a horn, rather than a dipole antenna
or any other type of antenna, atthe focal point of the dish minimizes loss of energy (leakage)
around the edges of thedish reflector. It also minimizes the response of the antenna to
unwanted signalsnot in the favored direction of the dish.
Horn antennas are used all by themselves in short-range radar systems, particularlythose used
by law-enforcement personnel to measure the speeds of approaching or retreatingvehicles
6. Explain PATCH antenna (Dec 08/jan09)
A patch antenna is a wafer-like directional antenna suitable for covering single-floor small
offices, small stores and other indoor locations where access points cannot be placed
centrally. Patch antennas produce hemispherical coverage, spreading away from the mount
point at a width of 30 to 180 degrees.
Patch antennas are also known as panel, flat panel or microstrip antennas. They are formed
by overlaying two metallic plates, one larger than the other, with a dielectric sheet in the
middle. This type of antenna is usually encased in white or black plastic, not only to protect
the antenna, but also to make it easy to mount. Because they are flat, thin and lightweight,
patch antennas are often hung on walls or ceilings where they remain visually unobtrusive
and blend easily into the background.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 17
Unit- 5 & 6: Antenna Types
1. Explain Helical antenna (june/july07)
A helical antenna is a specialized antenna that emits and responds to electromagnetic fields
with rotating (circular)polarization. These antennas are commonly used at earth-based
stations in satellite communications systems. This type of antenna is designed for use with an
unbalanced feed line such as coaxial cable. The center conductor of the cable is connected to
the helical element, and the shield of the cable is connected to the reflector.
The length of the helical element is one wavelength or greater. The reflector is a circular or
square metal mesh or sheet whose cross dimension (diameter or edge) measures at least 3/4
wavelength. The helical element has a radius of 1/8 to 1/4 wavelength, and a pitch of 1/4 to
1/2 wavelength. The minimum dimensions depend on the lowest frequency at which the
antenna is to be used. If the helix or reflector is too small (the frequency is too low), the
efficiency is severely degraded. Maximum radiation and response occur along the axis of the
helix.
The most popular helical antenna (often called a 'helix') is a travelling wave antenna in the
shape of a corkscrew that produces radiation along the axis of the helix. These helixes are
referred to as axial-mode helical antennas. The benefits of this antenna is it has a wide
bandwidth, is easily constructed, has a real input impedance, and can produce circularly
polarized fields. The basic geometry is shown in Figure .
The parameters are defined below.
- Diameter of a turn on the helix.
- Circumference of a turn on the helix (C=pi*D).
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 18
- Vertical separation between turns.
- pitch angle, which controls how far the antenna grows in the z-direction per turn, and
is given by
- Number of turns on the helix.
- Total height of helix, H=NS.
2. Explain LOG PERIODIC DIPOLE ARRAY (june/july07)
The log periodic dipole array (LPDA) is one antenna that almost everyone over 40 years old
has seen. They were used for years as TV antennas. The chief advantage of an LPDA is that it
is frequency-independent. Its input impedance and gain remain more or less constant over its
operating bandwidth, which can be very large. Practical designs can have a bandwidth of an
octave or more.
Although an LPDA contains a large number of dipole elements, only 2 or 3 are active at any
given frequency in the operating range. The electromagnetic fields produced by these active
elements add up to produce a unidirectional radiation pattern, in which maximum radiation is
off the small end of the array. The radiation in the opposite direction is typically 15 - 20 dB
below the maximum. The ratio of maximum forward to minimum rearward radiation is called
the Front-to-Back (FB) ratio and is normally measured in dB.
Log-Periodic Dipole Array
The log periodic antenna is characterized by three interrelated parameters, andas well
as the minimum and maximum operating frequencies, fMIN and fMAX. The diagram below
shows the relationship between these parameters.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 19
Unlike many antenna arrays, the design equations for the LPDA are relatively simple to work
with. If you would like to experiment with LPDA designs, click on the link below. It will
open an EXCEL spreadsheet that does LPDA design.
3. Explain YAGI-UDA ARRAY (june/july10)
The Yagi-Uda array, named after the two Japanese physicists who invented it, is the most
common antenna array in use today. In contrast to the other antenna arrays that we have
already looked at, the Yagi has only a single element that is connected to the transmitter,
called the driver or driven element. The remaining elements are coupled to the driven
element through its electromagnetic field . The other elements absorb some of the
electromagnetic energy radiated by the driver and re-radiate it. The fields of the driver and
the remaining elements sum up to produce a unidirectional pattern. The diagram below
shows the layout of elements in a typical Yagi.
Behind the driven element is a single element that is approximately 5% longer. This is the
reflector. It prevents radiation off the back of the array. In front of the director are a series of
elements that are shorter than the driven element. These are the directors. They help focus the
radiation in the forward direction. Together the reflector and directors can reduce the
radiation off the back of the antenna to 25 - 30 dB below the forward radiation. As more
directors are added, the forward gain increases.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 20
4. Explain CORNER REFLECTORS (Dec 08/jan09)
To increase the directivity of an antenna, a fairly intuitive solution is to use a reflector. For
example, if we start with a wire antenna (lets say a half-wave dipole antenna), we could place
a conductive sheet behind it to direct radiation in the forward direction. To further increase
the directivity, a corner reflector may be used, as shown in Figure . The angle between the
plates will be 90 degrees.
5. Explain LENS ANTENNAS (Dec 08/jan09)
With a LENS ANTENNA you can convert spherically radiated microwave energy into a
plane wave (in a given direction) by using a point source (open end of the waveguide) with a
COLLIMATING LENS. A collimating lens forces all radial segments of the spherical
wavefront into parallel paths. The point source can be regarded as a gun which shoots the
microwave energy toward the lens. The point source is often a horn radiator or a simple
dipole antenna.
Waveguide Type The WAVEGUIDE-TYPE LENS is sometimes referred to as a
conducting-type. It consists of several parallel concave metallic strips which are placed
parallel to the electric field of the radiated energy fed to the lens, as shown in figure 3-10A
and 3-10B. These strips act as waveguides in parallel for the incident (radiated) wave. The
strips are placed slightly more than a half wavelength apart. Figure.—Waveguide lens.
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 21
6. Explain Parabolic reflector (June/july09) The most well-known reflector antenna is the parabolic reflector antenna, commonly known
as a satellite dish antenna. Examples of this dish antenna are shown in the following Figures.
Parabolic reflectors typically have a very high gain (30-40 dB is common) and low cross
polarization. They also have a reasonable bandwidth, with the fractional bandwidth being at
least 5% on commercially available models, and can be very wideband in the case of huge
dishes (like the Stanford "big dish" above, which can operate from 150 MHz to 1.5 GHz).
The smaller dish antennas typically operate somewhere between 2 and 28 GHz. The large
dishes can operate in the VHF region (30-300 MHz), but typically need to be extremely large
at this operating band.
The basic structure of a parabolic dish antenna is shown in Figure It consists of a feed
antenna pointed towards a parabolic reflector. The feed antenna is often a horn antenna with a
circular aperture.
Unlike resonant antennas like the dipole antenna which are typically approximately a half-
wavelength long at the frequency of operation, the reflecting dish must be much larger than a
wavelength in size. The dish is at least several wavelengths in diameter, but the diameter can
be on the order of 100 wavelengths for very high gain dishes (>50 dB gain). The distance
between the feed antenna and the reflector is typically several wavelenghts as well. This is in
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 22
contrast to the corner reflector, where the antenna is roughly a half-wavelength from the
reflector.
7. Explain Paraboloid (Dec 08/jan09)
The parabola is completely described by two parameters, the diameter D and the focal length
F. We also define two auxilliary parameters, the vertical height of the reflector (H) and the
max angle between the focal point and the edge of the dish ( ). These parameters are
related to each other by the following equations:
Unit- 7 & 8: Radio Wave Propagation
1. Explain GROUND WAVE PROPAGATION (Dec 08/jan09)
Ground Waves are radio waves that follow the curvature of the earth. Ground waves are
always vertically polarized, because a horizontally polarized ground wave would be shorted
out by the conductivity of the ground. Because ground waves are actually in contact with the
ground, they are greatly affected by the ground’s properties. Because ground is not a perfect
electrical conductor, ground waves are attenuated as they follow the earth’s surface. This
effect is more pronounced at higher frequencies, limiting the usefulness of ground wave
propagation to frequencies below 2 MHz. Ground waves will propagate long distances over
sea water, due to its high conductivity.
Ground waves are used primarily for local AM broadcasting and communications with
submarines. Submarine communications takes place at frequencies well below 10 KHz,
which can penetrate sea water (remember the skin effect?) and which are propagated globally
by ground waves.
2. Explain SPACE WAVE PROPAGATION (june/july09)
Space Waves, also known as direct waves, are radio waves that travel directly from the
transmitting antenna to the receiving antenna. In order for this to occur, the two antennas
must be able to “see” each other; that is there must be a line of sight path between them. The
diagram on the next page shows a typical line of sight. The maximum line of sight distance
between two antennas depends on the height of each antenna. If the heights are measured in
feet, the maximum line of sight, in miles, is given by:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 23
Because a typical transmission path is filled with buildings, hills and other obstacles, it is
possible for radio waves to be reflected by these obstacles, resulting in radio waves that arrive
at the receive antenna from several different directions. Because the length of each path is
different, the waves will not arrive in phase. They may reinforce each other or cancel each
other, depending on the phase differences. This situation is known as multipath propagation.
It can cause major distortion to certain types of signals. Ghost images seen on broadcast TV
signals are the result of multipath – one picture arrives slightly later than the other and is
shifted in position on the screen. Multipath is very troublesome for mobile communications.
When the transmitter and/or receiver are in motion, the path lengths are continuously
changing and the signal fluctuates wildly in amplitude. For this reason, NBFM is used almost
exclusively for mobile communications. Amplitude variations caused by multipath that make
AM unreadable are eliminated by the limiter stage in an NBFM receiver.
An interesting example of direct communications is satellite communications. If a satellite is
placed in an orbit 22,000 miles above the equator, it appears to stand still in the sky, as
viewed from the ground. A high gain antenna can be pointed at the satellite to transmit
signals to it. The satellite is used as a relay station, from which approximately ¼ of the
earth’s surface is visible. The satellite receives signals from the ground at one frequency,
known as the uplink frequency, translates this frequency to a different frequency, known as
the downlink frequency, and retransmits the signal. Because two frequencies are used, the
reception and transmission can happen simultaneously. A satellite operating in this way is
known as a transponder. The satellite has a tremendous line of sight from its vantage point in
space and many ground stations can communicate through a single satellite.
3.Describe SKY WAVES (june/july08)
Propagation beyond the line of sight is possible through sky waves. Sky waves are radio
waves that propagate into the atmosphere and then are returned to earth at some distance
from the transmitter. We will consider two cases:
ionospheric refraction
tropospheric scatter
4. Explain IONOSPHERIC REFRACTION (june/july09
This propagation mode occurs when radio waves travel into the ionosphere, a region of
charged particles 50 – 300 miles above the earth’s surface. The ionosphere is created when
the sun ionizes the upper regions of the earth’s atmosphere. These charged regions are
electrically active. The ionosphere bends and attenuates radio waves at frequencies below 30
MHz. Above 200 MHz the ionosphere becomes completely transparent. The ionosphere is
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 24
responsible for most propagation phenomena observed at HF, MF, LF and VLF. The
ionosphere consists of 4 highly ionized regions
The D layer at a height of 38 – 55 mi
The E layer at a height of 62 – 75 mi
The F1 layer at a height of 125 –150 mi (winter) and 160 – 180 mi (summer)
The F2 layer at a height of 150 – 180 mi (winter) and 240 – 260 mi (summer)
The density of ionization is greatest in the F layers and least in the D layer Though created by
solar radiation, the ionosphere does not completely disappear shortly after sunset. The D and
E layers disappear almost immediately, but the F1 and F2 layers do not disappear; rather they
merge into a single F layer located at a distance of 150 – 250 mi above the earth.
Recombination or charged particles is quite slow at that altitude, so the F layer lasts until
dawn.
The critical frequency varies from place to place, and it is possible to view this variation by
looking at a real-time critical frequency map
The critical frequency varies from 1 to 15 MHz under normal conditions. Most
communications is done using radio waves transmitted at the horizon, to get the maximum
possible distance per hop. The highest frequency that can be returned when the takeoff angle
is zero degrees is called the MUF, maximum usable frequency. The MUF and critical
frequency are related by the following formula:
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 25
5. Write a note on ionospheric propagation (Dec08/jan09)
The ionosphere also attenuates radio waves. The amount of attenuation is roughly inversely
proportional to the square of the frequency of the wave. Thus attenuation is a severe problem
at lower frequencies, making daytime global communications via sky wave impossible at
frequencies much below 5 MHz.
The properties of the ionosphere are variable. There are 3 periodic cycles of variation:
diurnal (daily) cycle
seasonal cycle
sunspot cycle
The daily cycle is driven by the intensity of the solar radiation ionizing the upper atmosphere.
The D and E layers form immediately after sunrise, and the F layer splits into two layers, the
F1 and F2. The density of the layers increases until noon and then decreases slowly
throughout the afternoon. After sunset, the D and E layers disappear and the F1 and F2
merge to form the F layer. Take another look at the real-time MUF map and notice the
difference between the MUF numbers in the day and night regions. If you aren't sure which
region is the daytime region, it has a small yellow sun icon in its center. The thick gray lines
indicate the location of the terminator - the division between day and night.
Seasonal variation is linked to the tilt of the earth’s axis and the distance between the earth
and sun. The effects are complex, but the result is that ionospheric propagation improves
dramatically during the for the northern hemisphere during their winter, while seasonal
variation in the southern hemisphere is much smaller.
The 11 year sunspot cycle exerts a tremendous effect on the atmosphere. Near the peak of the
cycle (the last peak occurred in December 2001) the sun’s surface is very active, emitting
copious amounts of UV radiation and charged particles, which increase the density of the
ionosphere. This leads to a general increase in MUF’s and attenuation at lower frequencies.
When the sun becomes extremely active, or a major solar flare occurs, the ionosphere can
become so dense that global ionospheric communications are disrupted.
The maximum distance that can be covered by a single hop using ionospheric propagation is
about 2500 miles. Greater distances can be covered using multi-hop propagation, in which
radio waves are reflected by the ground back up to the ionosphere.
The ionosphere is not uniform and different regions refract RF differently. Multipath
propagation is the result. This leads to rapid variations in the received signal amplitude
known as fading.
One of the consequences of ionospheric propagation is that reception of signals on the AM
broadcast band varies greatly from day to night.
6. Explain SPORADIC-E PROPAGATION (Dec08/jan09)
For reasons that are not clearly understood, clouds of densely ionized gases appear in the E -
layer of the ionosphere. The clouds are generally relatively small and can happen at any time
of day. These clouds are formed throughout the year, but are most common in the summer
Antennas and Propagation 10EC64
Dept of ECE, SJBIT 26
months. Because these clouds are so densely ionized, they can support ionospheric
propagation at frequencies well above the normal MUF. Sporadic E propagation has been
observed at frequencies as high as 144 MHz, and is relatively common at 50 MHz.
The E-layer is lower than the F-layer and as a result, the distance covered by a sporadic-E
hop is approximately 1000-1300 miles, depending on the cloud's height. The sporadic-E
clouds drift through the E-layer, adding to the unpredictability of sporadic-E propagation.
Sporadic-E propagation is not generally useful because of its unpredictability. Its main
impact is negative, causing VHF-TV and FM broadcasters in different markets to interfere
with each other.
7. Explain TROPOSPHERIC SCATTER (june/july09)
Regional over the horizon communications are possible through a sky wave technique called
tropospheric scatter (troposcatter or just tropo). As shown in the diagram below, the
troposphere, which is the layer of the atmosphere closest to the ground, has pockets or cells
of air within it that have a different water vapor content and therefore a different refractive
index for radio waves. As a result, radio waves are scattered by the cells over the horizon.
This scatter occurs at frequencies of 0.3 – 10 GHz. Operation above 10 GHz is not possible
because water vapor in the air strongly absorbs the signals This scattering process is not
efficient and very little of the transmitted signal is scattered in the direction of the receiver.
High power transmitters and sensitive receivers are required.
The troposphere contains almost all of the earth’s weather patterns, which makes the
troposphere’s properties quite variable. This makes troposcatter communications subject to
weather induced fading and communications blackouts. To improve the reliability of
troposcatter links, a technique called diversity operation is used. There are three types of
diversity:
Frequency Diversity – two frequencies simultaneously transmit the same signal
Polarization Diversity – radio waves of both polarizations are transmitted simultaneously
Space Diversity – pairs of widely separated antennas are used for transmitting and receiving
Diversity operation greatly increases the reliability of troposcatter links, but it comes at a
significant cost, because at least double the amount of equipment is needed at each
installation.