product release letter - avevadownloads.aveva.com/10509/d10509.pdf · product release letter ......

QA4/1, QA7/2 & QA11/3 - DNote v4.24 (6-May-14)

Product Release Letter

For further information please contact your local AVEVA support office, which can be found at http://support.aveva.com

This document has been prepared and approved by the following:

Job Title Name

Product Owner Charles Moses

AVEVA Electrical Senior Product Specialist

Product Manager Chris Binns

AVEVA Electrical and AVEVA Instrumentation Product Manager

System Test Manager Neeraja Tottempudi

Test Manager

TPS Representative for EDS products Semra Hamitogullari Åberg

Manager, Training and Product Support (EDS)

File: d10509.doc Last saved: 06th July, 2015 Copyright 2015 AVEVA Solutions Limited of 24

AVEVA Electrical 12.1.SP3 Fix 8 (32 bit)

Partial Fix Release 10509-1

Windows 7 SP1 (32 bit or 64 bit) & Windows 8.1 (32 bit or 64 bit)

Dear Customer This letter introduces and describes this release, which is supported on the indicated platform(s).

This Release Contains

A partial release of AVEVA Electrical, which upgrades the full release 10495-1 AVEVA Electrical 12.1.SP3 The separately licensed products or product components installable from or upgraded by this release are as follows:

Product Code

Product Name Version Number

V00FN288 AVEVA Electrical with following modules (Plant): 12.1.SP3

Electrical Engineer

Electrical Designer

Electrical Wiring Manager

Security Manager

V00FN429 AVEVA Electrical with following modules (Marine): 12.1.SP3

Electrical Engineer

Electrical Designer

Electrical Wiring Manager

Security Manager

V00FN697 AVEVA NET Electrical Gateway 12.1.SP3

http://support.aveva.com/



Prerequisite for this release - operating system:

Minimum Supported O/S Version (for each supported platform)

Microsoft Windows 7 SP1 Professional (32 bit or 64 bit), Windows 8.1* Professional (32 bit or 64 bit)

Mandatory O/S Patches (for each supported platform)

Microsoft Windows 7 SP 1 or Windows 8.1 base release

Build Operating System Microsoft Windows 7 SP1 Professional (32 bit & 64 bit)

* See Windows 8.1 Support in Important Points to Note section of this document for information about required Microsoft .NET Framework versions when deploying AVEVA Electrical 12.1.SP3 with Windows 8.1.

Please note that recommended/supported hardware and software configurations are constantly subject to review, so please consult the AVEVA support web pages for the latest recommendations.

Prerequisite for this release - products:

AVEVA Electrical 12.1.SP3

o Full 12.1.SP3 release 10495-1

o Full 12.1.SP3 release 10495-1 plus partial 12.1.SP3 Fix 2 release 10499-1





o See http://support.aveva.com

AVEVA Licensing System 1.3 and an appropriate licence file o Please see AVEVA Licensing 1.3 o AVEVA Flexman licensing no longer supported o ALS 1.3 is not supported for Windows 8.1 and therefore it must be installed on a

machine with a supported operating system. Please read the ALS 1.3 installation guide for details

Microsoft .NET Framework 4.0 o The English version is included in the Product folder under Microsoft .NET

Framework 4.0 English. For all other versions please see http://www.microsoft.com/en-gb/download/details.aspx?id=17718

o See Windows 8.1 Support in Important Points to Note section of this document Microsoft Office 2007, 2010 or 2013 (32 bit or 64 bit)

o Required to open datasheets within AVEVA Electrical and AVEVA Instrumentation 12.1.SP3

Works (is compatible) with:

AVEVA Instrumentation 12.1.SP3 Fix 6 AVEVA Engineering 14.1.0 including Fixes 1, 2, 3 and 4 AVEVA Engineering 14.1.SP1 including Fix1 and 2 AVEVA Diagrams 14.1 including Fix1 and 2 AVEVA Integration Service 1.0 & 1.1 AVEVA Administration 1.2 and above AVEVA P&ID 12.1 and above (32 or 64 bit)

o 12.1.SP2 Fix 1 or above recommended AVEVA PDMS 12.1 and above AVEVA Outfitting 12.1 and above


http://support.aveva.com/services/products/30377/alic_30377.asp

http://www.microsoft.com/en-gb/download/details.aspx?id=17718



AVEVA E3D 1.1 and above AVEAVA NET Portal 4.7 and above AVEVA NET Work hub and Dashboard 5.0 and above AutoCAD 2013, 2014 & 2015*

VBA Enabler for AutoCAD not required for AVEVA Electrical 12.1.SP3 o Designer Drawing functionality not supported with AutoCAD 2012

Microsoft Excel 2007, 2010 and 2013 Microsoft SQL Server 2008 R2 SP2, 2012 and 2012 SP1

o SQL Server Express also supported Citrix XenApp 6.5 (64 bit) ETAP 14.0 & above (64 Bit Software only) **

* Please check that the version of AutoCAD deployed within a Citrix environment is certified for Citrix use and that the AutoCAD licensing is compliant. Click this link for more information http://usa.autodesk.com/adsk/servlet/item?siteID=123112&id=13959101 * There is an issue with Designer Drawing using AutoCAD 2015. See Defect number 174934 in Significant Defects and Recommended Workarounds section ** Please contact OTI for confirmation of release date ETAP 14.0 is compatible with:

Microsoft Excel 2007, 2010 and 2013 Microsoft SQL Server 2008 R2, 2012 and 2014 Microsoft SQL Express is also supported

Integration Matrix

This fix/update release of AVEVA Electrical 12.1.SP3 supports a new method of integrating the AVEVA products. The AVEVA Integration Service removes the need to have the applications that you wish to integrate installed on the same workstation. Instead, the integration is managed by a windows service running on a separate machine that all project participants can access via the network.

This new method of integration is not available for all AVEVA applications yet and where available only for the latest versions.

The following table indicates which method of integration can be deployed with AVEVA Electrical 12.1.SP3 Fix 8.

AVEVA P&ID Local Integration Services Integration Notes

12.1 to 12.1.SP2 Fix 1 Yes No

12.1.SP2 Fix 2, 3, 4, 5, 6 & 7 Yes *Yes *12.1.SP2 Fix 6, 7 needed to

import loop data into AVEVA

Instrumentation

AVEVA Engineering

14.1 Yes No

14.1 Fix 1 & 2 Yes No

14.1 Fix 3 & 4 Yes Yes

14.1.SP1 & 14.1.SP1 Fix1 & 2 Yes Yes

AVEVA Diagrams

14.1 & 14.1 Fix1 & 2 No Yes

PDMS Engineering

12.1 to 12.1.SP2 Fix36 Yes No

12.1.SP4 Fix 17 to Fix 23 Yes *No *See Note 1 below

http://www.citrix.com/products/xenapp/overview.html?posit=glnav

http://usa.autodesk.com/adsk/servlet/item?siteID=123112&id=13959101

http://etap.com/

http://support.aveva.com/support/United_Kingdom/



PDMS Diagrams



PDMS Schematic Model Manager



PDMS Design

12.1 to 12.1.SP2 Fix 36 Yes No


E3D Design

1.1 and fixes Yes *No *See Note 1 below

2.1 Yes *No *See Note 1 below

Notes:

1. Will be supported in the future release of AVEVA Electrical

2. See Scenarios Whereby a Blank Compare/Update Dialogue is Presented in the Important Points to Note section of this document

Supersedes

This release supersedes the previous fix release 10508-1, AVEVA Electrical 12.1.SP3 Fix 7.

To install product release

Please run the file Electrical12.1.3.8.exe. Running this executable will upgrade the following installations to AVEVA Electrical 12.1.SP3 Fix 7:

o AVEVA Electrical 12.1.SP3 (Full release 10495-1)

o AVEVA Electrical 12.1.SP3 Fix 2 (Partial release 10499-1)





Due to the AutoCAD issue below AVEVA Electrical 12.1.SP3 Fix 6 was withdrawn. In order to fix Incident Number 77987 (Area No is not available for Designer Drawing Symbols) and 79704 (Designer Drawing has an AutoCAD error during opening of the application) on 32 or 64-bit machines, an extra installer has been added to the release. It is called AVEVA.AutoCADUpdate.exe.

Run the file AVEVA.AutoCADUpdate.exe to update AutoCAD binaries that enable the AutoCAD based features of AVEVA Electrical to function correctly.

NOTE: This update should be applied for all supported versions of AutoCAD (2013, 2014, 2015) and for both 32-bit and 64-bit operating systems. To install this update successfully, right-click on the .exe and then select "Run as Administrator" from the options.



IMPORTANT NOTE This 12.1.SP3 Fix 8 must be installed directly on top of AVEVA Electrical 12.1.SP3 or AVEVA Electrical 12.1.SP3 Fix 2, Fix 3, Fix 4, Fix 5 or Fix 7. Please uninstall AVEVA Electrical 12.1.SP3 Fix 1 prior to installing this fix if you have it installed.

First released on

This product release is first available on AVEVA support website http://support.aveva.com as AVEVA Electrical 12.1.SP3 Fix 8, release number 10509

List of Enhancements

This release includes the following functional enhancements: Description

ETAP Interface Within the Engineer module there is the option to import and export ETAP engineering data. The configuration dialogue allows the project to setup the interface folder location and the names of the xml files used to import and export the engineering data. Configuration dialogue allows the project to map any ETAP field to an existing database field or new property field. The Engineer module’s ETAP Import uses a compare / update wizard which includes a graphical representation of the power distribution. In order to help users there are 2 package projects available that are synchronised with example projects in the ETAP 14 release. These can be found in an ETAP folder which itself is in the application install folder under Program Files (x86). One package project (ETAPCleanProject.pkg) is an empty project ready to receive project data from ETAP 14. The second package project (SourceDataForETAP.pkg) is a populated project ready to send project data to an empty ETAP 14. For the full details of the ETAP Element Types supported with this release please see training documentation Note: This fix release has been tested against the released version of ETAP 14

Incident number

Defect number

Module Description

47199 72951 Designer We need to be able to import SCSUBE into AVEVA Electrical

List of Fault Corrections

This release addresses defects arising from the following support incidents:

Incident number

Defect number

Module Description

77205 160891 Designer SLD Designer Drawing Explorer is missing none load tags and none power cables

82370 175462 Engineer Exception when creating a project from a Package

77203 160885 Engineer Load List report does not include field attributes that show power values for both load and supply tags

75483 164940 Designer AVEVA Designer Drawing changing AutoCAD environment colour to black automatically

78277 165224 Security Manager

While updating the length in AVEVA Electrical from Outfitting the wrong license is being used and not being released

78617 165206 Engineer When External Cable Sizing has been executed the Number of Cables value is always being set to 1




Incident number

Defect number

Module Description

81164 172879 Engineer When using 'Move Compartment to' option an exception is displayed in Distribution Diagram screen

81165 172880 Engineer Exception is displayed when using bulk edit in the Browse Data by Form Type

78980 166804 Engineer Need to add Area Path column in Wiring Manager module's Equipment List

80001 171857 Engineer Need to see Speed attribute in Load Schedule

81166 172881 Engineer Need to see equipment User Fields in datasheets

81167 172882 Engineer Need to see equipment User Fields in load schedule

81694 174070 Engineer Cable Check Report comparing wrong current values

81697 174074 Engineer Cable Schedule 'Need Re-Sizing' field is not being set correctly on press of Refresh button

72059 146448 Engineer Issue when Importing Compartment Elements From Other Project

69948 140069 Engineer Exception when importing compartment element symbols from other project

79466 168295 Designer Cable numbers not aligned properly on termination drawings

79339 167935 Engineer Revisions Button in the actions pane doesn't work if security rights are enabled

78563 166669 Designer Template displays instead of the drawing once the template is modified

78592, 75207

165110, 164942

Designer Global Datalink Edit is not available

77495 161843 Wiring Manager Exception when creating an Area via Equipment View

75876 157339 Wiring Manager

Possible to add cables of different catalogue type to same cable drum

79465 168293 Designer Cable pairs and screen are overlapping on termination diagrams

79496 168551 Engineer Open Datasheet doesn’t commit changes to record

82999 176561 Designer Unable to enter date drawn, design, checked or approved

83280 177220 Security Manager Upgrade issue when data contains apostrophe

n/a 165850 Wiring Manager

Edit Termination throwing warning message, “Your project database is not compatible with this version of AVEVA Inst I/O assignments. Please contact AVEVA.”

n/a 170441 Engineer, Wiring Manager

Description in not updated in Engineer when changed via Equipment List grid in Wiring manager

81451 173474 Engineer Problems with 'Order By' Attribute in grids

Consolidated from previous fix releases

First released in Fix Version AVEVA Electrical 12.1.SP3 Fix 7, Release No. 10508-1

Incident number

Defect number

Module Description

79704 169101 Designer Designer Drawing has an AutoCAD error during opening of the application




Incident number

Defect number

Module Description

75326 155048 Engineer Missing required columns in cable Catalogue Import Wizard

78428 164621 Engineer Cables are updated as an instrumentation cable after they have been sized


It is not possible to delete cables if DrumLocked field is not the grid view

77535 161844 Engineer When Security is enabled, error is caused by the report being run containing a sub report that no longer exists

76457 158795 Engineer Issues with Earth Resistor, Motor when importing Loads from excel

76458 158796 Engineer Excel load import is creating invalid circuits within Distribution Board tag

78455 164666 Designer Issue in Cabinet/Panel drawing designer symbols folder

78472 164683 Engineer ElecFaultCurrent field is missing in Datasheets

76636 159295 Wiring Manager Issue when updating cable Design Length as zero from E3D TM

76401 158634 Engineer Area No changing for Equipment without changes to audit log


Cannot delete unused Enhanced Cable Block Diagram Symbol from symbol library

74992 153914 Engineer Wiring Rule Name column changing appearance in Load Grid

75771 156821 Engineer Re-arrangement of columns in Cable Schedule grid is not being saved correctly

75474 155952 Engineer Unable to delete 2 Supply tags

75695 156454 Engineer 4 buttons of the Compartment Typical window are not presented on Windows 7 Enterprise K (Korean)

75499 155879 Engineer Transformer User Defined symbol does not have the Remove Out Connector and Remove the ER connector

75500 155891 Engineer Single Line Diagrams in Distribution Diagram missing Earth Resistor associated with supply transformer tag


Need Shield reference adding to Cable Catalogue and allow 1/C cable to have Shield data

72862 148820 Engineer Claimed items could be edited by other users

77295 161186 Engineer In Designer module import from other project option is not working for Installation Detail

77987 163341 Designer AREANO is not available for Designer Drawing Symbols. See To install product release: for further details if project is using 32-bit machines

78093 163632 Engineer Installation Detail Item Catalogue failure to import from other project

78233 78410

163999 164618

Wiring Manager

Grid View is not reporting correct Core Size but it is represented correctly in Form View

77319 161243 Engineer Latest release shows the banner as “Not For Commercial Use” as part of install


Incident number

Defect number

Product / Module

Description

74533 152747 Engineer AVEVA Diagrams receives Busbar and Winding data from AVEVA Electrical



69909 139973 Designer Schematics drawing - Loads compartment datalinks are not correct

74287 152352 Engineer During Compare/Update Import for ETAP it is not possible to uncheck all the user fields

74289 152358 Engineer During Compare/Update Import for ETAP two compartments are being created for a coupler

72074 146531 Engineer Out Memory Issue when user runs Excel import more than 30 times


Unable to see CBD and ECBD under AVEVA Electrical Wiring Manager Cable Block Diagrams Menu

72114 146622 Engineer Distribution Diagrams Null Reference Exception when Access Control is enabled

74275 152342 Engineer When importing a motor tag via excel without mapping MotorCatalogueNo the Data Source for Calculation is not set

74797 153486 All General performance improvements in grid management and MS Excel import

73663 150923 Security Manager

Timeout upgrading large projects when resolving DB collation conflicts

74729, 74676

153479153472

Engineer Datasheet Document List publish to PDF problems


Unable to see cable block diagrams and enhanced cable block diagrams following project upgrades from SP3, Fix 1, Fix 2 and Fix 3


Incident number

Defect number

Product / Module

Description

74658 152986 Engineer Unable to import tagged items via AVEVA Diagrams Import when non mandatory fields are mapped

N/A 153518 Engineer Unable to import tagged items via AVEVA P&ID Import when non mandatory fields are mapped


Incident number

Defect number

Product / Module

Description

73604 150736 Designer Unable to create Designer SLD after windows date format changed

73446 150202 Engineer Reassign of tag equipment is not working in Supply Details dialogue

70660 142024 Engineer Exception when re-assigning loads/supplies importing from Excel

69252 138008 Engineer Unable to select more than 4 single conductor cables or edit cable numbers

70296 140980 Engineer ElecFaultCurrent is missing in Drawing Designer Symbols


Incorrect Cable Route Status update in compare and update with E3D Cable Design

146569 72081 Engineer Automatic mapping for certain fields in the Load Import are not correct i.e. Function, Number

71127 143377 Engineer Unhandled exception error when right clicking in Compartment Typical dialogue box

72229 147071 Engineer Distribution Diagrams Read Only Assignments error

70661 142025 Engineer It is possible to reassign loads and move elements in an MCC assigned to a read-only area



70662 142028 Engineer It is possible to change some details for Transformers assigned to read-only areas via the Transformer Detail window

73450 150208 Engineer Exception when selecting "Copy Selected" in the motor catalogue

67071 128487 Engineer Cable Sizing Check Report is not working correctly for cable length

71617 145295 Engineer New load connections being incorrectly identified as circuit breaker in KOL Distribution Diagram window


Incident number

Defect number

Product / Module

Description

73088 149449 Designer This is an AVEVA Electrical 12.1.SP3 Fix 1 patch issue. The patch is replacing 64 bit files with 32 bit which causes an error. The error is that it is not possible to load any designer drawings and a message is displayed in the AutoCAD command window


Incident number

Defect number

Product / Module

Description

72260 147162 Engineer The equipment voltage is not set correctly from excel on import for load items other than motor which causes the equipment current to also be set incorrectly

72593 147959 Engineer Distribution Diagrams Supplies creation error when creating tag containing a busbar

72594 147965 Engineer Distribution Diagrams tag creation error when 'Forced Tagging for KOL' enabled in Options dialogue

72873 148865 Engineer During the excel import the equipment voltage is not been checked against project voltage when an items voltage is not set to the applications default voltage it gets imported with the wrong data

PRODUCT QUALITY STATEMENT

The development, maintenance and testing of AVEVA Solutions’ software products is carried out in accordance with the company’s KEYSTONE lifecycle processes and this document includes a summary of the testing carried out on this release and a list of significant defects known to exist at the time of release.

Development Testing

Developers have carried out unit testing of each enhancement and/or fix in the development environment to verify that any new functionalities have been correctly implemented and identified defects have been corrected. Regression tests have been run in the development environment to verify that enhancements and/or fixes have not adversely affected the integrity of the product.

System Testing

Limited independent system testing has been carried out on this product, as released, to verify that it installs correctly in all supported configurations that any new functionalities have been correctly implemented and identified defects have been corrected.



Acceptance Testing

AVEVA’s Product Readiness Authority (PRA) is satisfied that the System Testing for this release is sufficient to assure product quality. Any exceptions found after release will be reported in the Product Release Latest Update Note on AVEVA's support web site http://downloads.aveva.com/10509/w10509.pdf

Exceptions – Significant Defects and Recommended Workarounds

AVEVA intends to fix the defects listed below in a fix release or service pack as soon as reasonably possible. Incident number

Defect number

Description Recommended Workaround

47066 72738 When user wants to create wiring rule for VFD there is a requirement for multiple power cables. Also there are data links missing when motor schematic requires a variable speed drive

None except edit AutoCAD drawing manually after creation

54821 91710 When user connects a Motor to a Variable Speed Drive and the Motor has had its diversity factor set to 50% then at the Variable Speed Drive shows the average power over time and not the maximum demand

For reports the user can do the calculation within the report to show the maximum demand of the motor

64338 118534 When project has Busbar with compartment data connected to Variable Speed Drive connected to Motor not all the data links are available for the Motor Schematic drawing


58648 101031 When the tag number format was changed only the Cable Number was clouded, the Tag number and the ferrule number was not clouded


54257 90276 When the tag number format was changed only the Cable Number was clouded, the Tag number and the ferrule number was not clouded


54822 91711 Power Factor field is required for Supply tags

None

52297 86351 The user is permitted to create a new cable from supply equipment to load equipment when the loads have NOT being assigned to Supplies. When cables are created in this manner and the user wants to size the cable from the cable schedule the user is prevented from doing so. If the user then assigns loads to supplies after the cable has been created, the user is still unable to size the cable from the cable schedule

The user has to delete the cable from the cable schedule, re-create the cable (after assignment), and then the cable can sized

64437 67071

118885 Currently if the number of terminals is changed (or the number of cores in a cable) then all of the data link names will change resulting in the user having to re-edit the already completed schematic template

The user having to re-edit the already completed schematic template

http://downloads.aveva.com/10509/w10509.pdf



Incident number

Defect number


68566 135590 When trying to copy load schedule reports none of the sub-reports are being copied over

Manually recreate sub reports

54827 91717 The circuit naming for Distribution Boards is a concatenation of Circuit Number plus Phase Identifier

None

57968 103836 Customer types in Edit Data links form the following SQL-request containing Cyrillic symbols: (select Description from Equipment where EquipmentNo= 'QF1 Ввод1'). However in the text field we got the abracadabra. This occurs on AutoCad 2010/2013

None

66472 126455 The main characteristic of this new equipment type is that there are 2 or more inputs (supplies) and only 1 output

At present the only option is to use a MCC with 2 incomers feeding a busbar feeding 1 output

45024 71208 Copying a transformer in the supplies tab

does not copy over the winding impedance data

Add data manually

58624 100927 When importing from excel the Remarks attribute (for instance) and the text in the Excel file is larger than the attribute declaration in SQL (nvarchar(100)). The import reports an error (the message is not clear at all) and the data is not imported

None

N/A 89846 Picture/Logo Sizing on Datasheets Problems have been discovered with the sizing of images inserted into datasheet templates when the corresponding datasheets are previewed within AVEVA Instrumentation. This problem is a defect within the 3rd party components used by AVEVA Instrumentation and Electrical and has been reported to the respective suppliers. To avoid this issue please insert any image files in BMP format



Incident number

Defect number


N/A 136620 Intermittent “Warning 1946” error displayed when installing AVEVA Electrical and AVEVA Instrumentation

Warning messages beginning “Warning 1946” relating to short-cut links not being set have been observed intermittently whilst installing AVEVA Electrical and AVEVA Instrumentation 12.1.3. Clicking OK to close this warning should enable the installation to complete. No problems have been observed trying to then launch any of the AVEVA Electrical or AVEVA Instrumentation modules

N/A 129886, 130884

Problems printing/exporting to PDF Intermittent problems have been observed printing and exporting to PDF from both AVEVA Electrical and AVEVA Instrumentation 12.1.SP3. This may be due to limitations in the 3rd party control used for this document creation in a 64-bit environment. If you experience problems printing or exporting to PDF, please contact AVEVA Technical Support

N/A 139807, 139813

Exception error displayed when publishing datasheets and document lists to AVEVA NET portal if xlsx is the chosen file format and MS Office 2010 is deployed with AVEVA Instrumentation.

Documents must be created in xls format and not xlsx. AVEVA NET Gateways for AVEVA Electrical currently has problems related to xlsx file format support. Updated AVEVA NET Gateways for AVEVA Electrical will be incorporated into a fix for SP3 as soon as possible

70587 141871 Version of SQL Server is incorrect on the SQL Server login form

SQL Server login screen presented when creating new projects states, “This AVEVA product supports: SQL Server 2008 R2 (SP3)”. This note should state “SQL Server 2008 R2 (SP2)”

70661 72229

142025 147071

It is possible to re-assign loads and move elements in an MCC assigned to a read-only area. For Read Only MCC and Read Only Load Distribution Diagrams allows the assignment of Load to the MCC

Problem applies to right mouse-click in both the Distribution Diagram and also the Supply Details window. No work around currently



Incident number

Defect number


70662 142028 It is possible to change some details for Transformers assigned to read-only areas via the Transformer Detail window

Problem applied to adding windings, adding output voltages and assigning/un-assigning loads. No work around currently

68567, 71113

135586, 143355

Cable catalogue import problems Importing cable catalogue data from MS Excel requires 4 additional columns adding to the spread sheet. These columns are; “Line Type”, “Line Colour”, “Line Width” and “Arrow Head”. Please see the Cable Catalogue Import section of the Important Points to Note below

71635 145327 Issue with Cable Catalogue Importing cable catalogue data from MS Excel requires 4 additional columns adding to the spread sheet. These columns are; “Line Type”, “Line Colour”, “Line Width” and “Arrow Head”. Please see the Cable Catalogue Import section of the Important Points to Note below

71660 145355 Load schedule report does not show any data in AVEVA Electrical 12.1.SP3 after upgrade

If the load schedule report does not show any data then the filter string property needs to be cleared from edit layout of the report. Please see the Load Schedule Report error section of the Important Points to Note below

N/A 145632 After user has mapped attributes and saved mappings, then pressed Next button to Select Valid Records screen and pressed Back button to Select Mappings screen, the mapping some of fields are not showing any caption name e.g. "EqType" rather than "EqType (Equipment Type)"

Close Import Wizard and restart Import



Incident number

Defect number


N/A 146360 Irrespective to type of equipment, all the fields that are mapped in configuration window are seen when import is perform from AVEVA Engineering 14.1 to AVEVA Electrical - Engineer

Ensure when mapping fields for Load or Supply equipment types the same attribute in AVEVA Engineering 14.1 is used to map to the same attribute in AVEVA Electrical for both Load and Supply equipment types. Alternatively, if the same attribute in AVEVA Electrical for Load is mapped to a different AVEVA Engineering attribute compared to AVEVA Electrical attribute for Supply then the attribute value for the 2 mapping needs to be the same

72002 146381 Although cable size correctly stored in database the Cable Catalogue Details and Cable Sizing dialogues are displaying Decimal full stop rather than comma

Reset Size from within Cable Catalogue Detail

72059 146448 When Importing Compartment Elements From Other Project properties are not having the data transferred

Map fields manually

72095 146591 When Importing Compartment Elements Catalogue data from Excel type, Catalogue No, Model fields are not automatically mapped to correct field. Import for Rated Current is incorrect when decimal comma option is selected

Map fields manually. Update Rated Current value after import or import values with decimal set as point

N/A 146945 When AVEVA Electrical calculated attributes are mapped as part of Excel Load import then the power fields are not updated

Ensure AVEVA Electrical calculated fields are not part of Excel Load import

N/A 161004 Problems importing data into a shared project when duplicate properties exist in AVEVA Electrical and AVEVA Instrumentation

Ensure that property names are unique in AVEVA Electrical and AVEVA Instrumentation. See Importing Data into a Shared Project Where Duplicate Property Names Exist for AVEVA Electrical and AVEVA Instrumentation in Important Points to Note section below

N/A 174934 There is a system error when opening Designer Drawing on AutoCAD (2015). This is because the default setting for ‘STARTUP’ is set to 2

When opening AutoCAD 2015 for Designer Drawing there is a warning message telling the user that ‘STARTUP’ needs to be set to 0



Incident number

Defect number


N/A 176958 When rated current data found in Supply Details dialogue is imported from etap and the power factor does not equal one then changing rated current value causes an automatic update before user has completed data entry

Update rated load field value found in Supply Details dialogue. The Rated Current field value is then calculated correctly

n/a 170917 When changes are made within the AVEVA Electrical or AVEVA Instrumentation Integration Service Editor, clicking refresh is not displaying the changes. For example, when the authentication type for project ABC is changed from "Windows" to "Project Authentication", after clicking refresh, the changes are not reflected in the Integration Service editor dialogue

Click on Save button to see changes reflected in Integration Service editor dialogue

n/a 180184 Exception error when creating properties where the property name contains an apostrophe

User defined properties do not support the inclusion of apostrophes within the property name. Please do not attempt to include apostrophes in user defined property names.

For the latest list of exceptions and other updates, please see the Product Release Latest Update Note on AVEVA's support web site http://downloads.aveva.com/10509/w10509.pdf Please refer also to the Product Release Latest Update Note for the original full 12.1.SP3 release, http://downloads.aveva.com/10495/w10495.pdf

Important Points to Note

Mapping Tag Codes to Enable Integration

When importing tagged objects via Microsoft Excel or other AVEVA applications as part of the AVEVA Integrated Engineering & Design solution, all component parts (tag codes) of the tag number should be mapped to ensure accurate data transfer. This was the recommended approach for 12.1.SP2 and is now mandatory for some importing when deploying 12.1.SP3. These additional mandatory fields will ensure that it is not possible to import mismatched tag code and tag number data. Example: Instrument Tag 01-FT-001/A (tag format, Area – Function – Number / Suffix) Mandatory Fields to map for import:

Tag Class Tag Format Area Path Area Function Number Suffix





Windows 8.1 Support

When creating projects using AVEVA Instrumentation or AVEVA Electrical, 3rd party technology is leveraged to “unpackage” the empty or demo project structures. This technology only supports Microsoft .NET Framework up to version 3.5. Windows 8.1 installs Microsoft .NET Framework version 4.5 and this will not allow AVEVA Instrumentation or AVEVA Electrical to create projects. Windows 8.1 does not include .NET 3.5 by default. However users can enable this feature via Program and Features. See this link for more information http://support.microsoft.com/kb/2785188 Note: If users are upgrading from Windows 7 to Windows 8.1, .NET Framework 3.5 is fully enabled.

Project Packager and Microsoft’s Shared Management Objects (SMO)

Certain Microsoft assemblies required for the new Project Packager functionality to run are not shipped with AVEVA Instrumentation or AVEVA Electrical 12.1.SP3. When running the new Project Packager utility, if these assemblies are not detected, the following message will be displayed.

By clicking the links, in the order indicated, users will be able to download the required msi files and install the assemblies. Once installed, the new Project Packager will run without any problems. Note: This is a one-time action per machine.

Upgrading projects with the new AVEVA Project Authentication enabled

Once the new AVEVA Project Authentication has been enabled, projects can be upgraded in two ways. Both these methods require a SQL Server user login with the ‘dbowner’ role for the project. The recommended method is to upgrade the projects via AVEVA Security Manager. Security Manager by-passes the AVEVA Project Authentication and only allows Windows authentication or SQL Server authentication to connect to the project. If selecting Windows authentication, you will be asked to enter the Security Manager Administrator username and password. Providing your Windows domain account has a ‘dbowner’ role for the project, you will be able to upgrade the project. If selecting SQL Server Authentication, you will be asked to enter a SQL Server login name and password. Providing a login username and password is entered that has a ‘dbowner’ role for the



project, the project will upgrade. If a SQL login username and password is entered that does not have a ‘dbowner’ role for the project, the upgrade will not be permitted. The other method of upgrading a project is via the actual applications such as Engineer or Wiring Manager. If one of these applications is launched and a pre-SP3 project is selected, you will be first asked to enter the AVEVA Project user name and password.

Once you have entered these credentials, you will be asked if you wish to upgrade the project. If you say yes to the various messages, you will be asked to enter the AVEVA Security Manager Administrator username and password.

Lastly you will see this SQL Server Admin Login dialogue.

The reason for this dialogue being presented is because the SQL login user being leveraged by the new Project Authentication (IDOADMIN) does not have a ‘dbowner’ role for the project. To upgrade the project from this point, a different SQL login username and password must be entered that does have a ‘dbowner’ role for the project. This SQL login will have to be created by your SQL Server administrators.

Changing Authentication Type

AVEVA Instrumentation and AVEVA Electrical 12.1.SP3 allow projects to be configured with 3 different authentication methods. These are Windows authentication, SQL Server authentication and the new AVEVA Project authentication.



If the authentication type for a project needs to be changed, for example from Windows authentication to AVEVA Project authentication, this must be done via Security Manager. Irrespective of the authentication method (Windows or SQL Server) selected to connect to the project via Security Manager, the user login on the SQL Server must have a ‘sysadmin’ role to perform this task. Either changing authentication method for a project, or changing the AVEVA Project authentication password requires a login on the server with a ‘sysadmin’ role. Most users will not have a ‘sysadmin’ role on the server. Therefore to perform these tasks one of two things must happen:

1. The SQL Server administrator assigns temporary a ‘sysadmin’ role to the user attempting to change authentication method or AVEVA Project authentication password

2. A different user – that has a ‘sysadmin’ role on the server - has to perform these task

AutoCAD 2014 (and above) File Loading Security Concern

When launching AutoCAD 2014 (and above) from AVEVA Instrumentation 12.1.SP3, or AVEVA Electrical 12.1.SP3 warning messages such as the following may be seen.

AutoCAD 2014 (and above) has inbuilt functionality for checking trusted locations of dll’s that are being loaded. To prevent these types of message being displayed, implement the following steps:

1. Open any drawing in AutoCAD 2014 (and above) 2. Right click in the drawing area 3. Go to last option "Options" 4. Open 1st tab "Files" 5. Expand Node "Trusted Locations" 6. Add the following paths under the “Trusted Locations” node

a. AVEVA Instrumentation - C:\Program Files (x86)\AVEVA\Instrumentation12.1.3 b. AVEVA Electrical - C:\Program Files (x86)\AVEVA\Electrical12.1.3\ACAddIn

7. The trusted location paths detailed above are based on the default installation folders for AVEVA Instrumentation 12.1.SP3, or AVEVA Electrical 12.1.SP3

8. Once the trusted locations have been added, the Security Concern messages should no longer be displayed when launching AutoCAD 2014 (and above) from within AVEVA Instrumentation 12.1.SP3, or AVEVA Electrical 12.1.SP3

Area Numbers on Reports following Project Upgrades

After upgrading projects, Instrument or Loop reports may no longer display area values. This is because the area number is no longer stored in the InstrumentList or LoopList tables. Instead the area data is now stored in the Area table. To fix the problem, edit the affected reports to display the AreaNo data from the Area table instead of the AreaNo data from the InstrumentList or LoopList tables



For further assistance, please contact AVEVA Technical Support How to avoid Timeout error during loading of grids A timeout issue was reported for 12.1.SP2 when loading very large data sets via the default grids in AVEVA Electrical and AVEVA Instrumentation. This has been addressed in 12.1.SP2 Fix 3 and later releases. However, if any users have created their own grids and apply filters to these grids, the process of filtering will slow down the loading of the grids and the timeout problem may resurface. To avoid this problem users can adjust the existing setting “CommandTimeoutSeconds” in the inst.ini file. Users can set higher values to avoid any timeout errors. This is applicable for both AVEVA Electrical and AVEVA Instrumentation and all the grids.

Importing Records where Field and Property Names Match

Problems will occur if data import is attempted where fields and properties are named identically. To avoid this, ensure that properties are not named the same as any existing fields in the target database tables. The warning message will appear during import even if the Property is not mapped to the equipment type. Particular fields that may be an issue after the project has been upgraded are:

CatalogueNo for Equipment Type Transformer EquipmentType for Equipment Type Motor Voltage for Equipment Type MCC

Properties Named with Underscores

Property names containing underscore is not supported in AVEVA Electrical and AVEVA Instrumentation 12.1.SP3. To avoid problems with datasheet creation, reporting and grid management, do not create properties that contain underscores.

Importing Data via Microsoft Excel where duplicate field/column names are detected

For AVEVA Instrumentation and AVEVA Electrical 12.1.SP3 a solution has been implemented for a problem discovered importing data via the Browse Data By Form Type grid. The problem related to duplicate field and column names present in the grid and Excel spread sheets. AVEVA Instrumentation and AVEVA Electrical will now display any duplicate column/field name with a numeric suffix appended within the mapping screens for import. This change will impact all grids where data can be imported via Microsoft Excel. For example, if two “Description” fields/columns are detected, they will be presented as “Description” and “Description1”. This will apply to all work sheets within a workbook. In the example just described, the duplicate column name could be present on different worksheets. A consequence of this change is that existing mappings defined in pre-SP3 projects may not work, especially for importing data via the Equipment List in Wiring Manager. Here data for the Major Equipment, Components etc. can be imported from multiple worksheets within the same workbook. To re-use mapping defined in pre-SP3 projects, the multiple worksheets will have to be split out into separate xls or xlsx files and imported via these individual files. Alternatively, the mapping will have to be re-defined.

http://www.aveva.com/en/Products_and_Services/Product_Support.aspx



Importing Data into a Shared Project Where Duplicate Property Names Exist for AVEVA Electrical and AVEVA Instrumentation

Importing data into shared projects can be problematic if identically named properties exist in both AVEVA Electrical and AVEVA Instrumentation. For example, if a Motor property named “Prop01” is created in AVEVA Electrical and an Instrument property named “Prop01” is created in AVEVA Instrumentation, importing data into AVEVA Electrical from other integrated AVEVA applications can fail. To avoid this problem ensure that all properties – in both AVEVA Electrical and AVEVA Instrumentation – are named uniquely.

Importing Cable Catalogue Data via Microsoft Excel

Within the new functionality, delivered with AVEVA Instrumentation and AVEVA Electrical 12.1.3.SP3, users can now control how cables appear on the enhanced cable block diagrams. These graphical controls are accessible via the cable catalogue. Each cable catalogue entry has the following new properties on the Design Data tab of the Cable Catalogue Details dialogue.

Changing these properties will alter the graphical representation for any cable created from the associated catalogue entry. To enable the successful import of cable catalogue data from MS Excel, values for these new properties should be present in the xls or xlsx file. Columns should be added to the Excel spread sheet(s) as below.

The column data shown above is the default data for cable catalogue entries and can be set to other values if required. Once the spread sheet is picked for importing data, user should map the new columns as follows.

Once these columns and fields are mapped, all data will import successfully



Three known issues have been noted with the importation of cable catalogue data and Enhanced Cable Block Diagram data:

1. Exporting the Cable Catalogue to MS Excel does not automatically create and populate these columns in the spread sheet.

2. If these columns are not mapped and data imported for new cable catalogue entries, subsequent editing of the new cable catalogue entry will result in an error. This is because the Enhance Cable Block Diagram properties are empty.

3. Some values for properties such as OAS/Coll and Cores will not be imported or created correctly.

Duplicate named fields and properties causing problems importing data from MS Excel

AVEVA Instrumentation and AVEVA Electrical 12.1.SP3 now allows both fields and properties to be incorporated into the grids for data manipulation. Both field and property data can also be imported from MS Excel via the grids. Exposing all the existing properties has led to some instances where fields and properties with the same name and caption are displayed in the mapping screen when importing from Excel. An example of this can be found within the Instrument List. Now both InstrumentList.Description and ProcessData.Description are displayed as “Description (Description)” when mapping the columns to fields.

To enable users to differentiate between the two fields it is recommended that the captions are updated. For example, change the caption for InstrumentList.Description from “Description” to “Instrument Description” as follows.

Leading Spaces in Column Name Causing Problems Importing from MS Excel

A problem occurs if users attempt to import data from Excel if fields are mapped to Excel columns that have names with leading or trailing spaces. To avoid this problem, please ensure that all leading or trailing spaces have been removed for any Excel columns names mapped for data import. The message displayed states, “Field ‘ABC’ does not exist in the current import file.” For example…



In this case the column “Degree of protection” existed in Excel, but there are trailing spaces at the end of the column name. Removing these spaces enabled the data to import successfully.

Problems Initialising AVEVA Engineering for Integration

When configuring AVEVA Electrical or AVEVA Instrumentation to integrate with AVEVA Engineering please ensure that AVEVA Engineering is not running on the background. If users attempt to integrate AVEVA Electrical or AVEVA Instrumentation with AVEVA Engineering running, a fail to initialise error message will be displayed. To avoid this, simply ensure that AVEVA Engineering is not running in the background whilst trying to configure the integration with AVEVA Electrical and AVEVA Instrumentation.

Load Schedule Report error

If the load schedule report does not show any data in AVEVA Electrical 12.1.SP3 after upgrade but it does show data in AVEVA Electrical 12.1.SP1 /12.1.SP1 then the filter string property needs to be cleared from edit layout of the report in AVEVA Electrical 12.1.SP3. The example below shows the field that needs to be cleared.

This filter string property error is fixed in AVEVA Electrical 12.1.SP3



Problems Initialising AVEVA Engineering for Integration

When configuring AVEVA Electrical or AVEVA Instrumentation to integrate with AVEVA Engineering please ensure that AVEVA Engineering is not running on the background. If users attempt to integrate AVEVA Electrical or AVEVA Instrumentation with AVEVA Engineering running, a fail to initialise error message will be displayed. To avoid this, simply ensure that AVEVA Engineering is not running in the background whilst trying to configure the integration with AVEVA Electrical and AVEVA Instrumentation.

Installation Steps for AVEVA Integration Service

The following steps need to be followed to enable integration between AVEVA Electrical 12.1.SP3.8 Fix and other AVEVA application via the new AVEVA Integration Service.

Server Setup

1. From the AVEVA Electrical 12.1.SP3 Fix 8 installer package, extract the file ElectricalIntService.msi

a. Note What is ElectricalIntService.msi.txt

2. Copy ElectricalIntService.msi on to the machine (located on your network) that is hosting the AVEVA Integration Service

3. Run the ElectricalIntService.msi installer to add the AVEVA Electrical Integration Service

4. Follow AVEVA Integration Service 1.0 Installation Guide section 5.3 AVEVA Instrumentation/Electrical to add AVEVA Electrical projects to the AVEVA Electrical Integration Service

Client Setup

1. From the AVEVA Electrical 12.1.SP3 Fix 8 installer package extract the file Electrical12.1.3.8.EXE

2. Install this fix/update on all workstations currently running AVEVA Electrical 12.1.SP3, Fix 1, Fix 2, Fix 4, Fix 3, Fix 4, Fix 5 or Fix 7

3. Download and copy the AVEVA Integration Service 1.0 installer to all the workstations running AVEVA Electrical 12.1.SP3 Fix 8

4. Run the installer AVEVA_Integration_Service 1.0.msi and install the Integration Client, not the Integration Service

5. Follow the steps documented in the AVEVA Electrical 12.1.SP3 Fix 8 Common Functionality guide section 7.4.1 AVEVA Integration Import Configuration to setup integration between AVEVA Electrical and other AVEVA applications

Scenarios Whereby a Blank Compare/Update Dialogue is Presented

1. Importing one object type i.e. Loads when a grid for a different object type is active i.e. Supplies

a. Workaround to have grid active for object types being imported 2. Attempting to import using a group/mapping for product version “A” whilst connecting to

product version “B” a. Workaround is to ensure that the selected group/mapping relates to the connected

product version 3. Attempting to import using a group/mapping for project hosted on machine “A” whilst

connecting to machine “B” a. Workaround is to ensure that the selected group/mapping relates to the connected

machine 4. Mapped dabacon UDAs are deleted or their name is changed via Lexicon



a. Workaround is to remove mapped UDA from mapping before deleting or changing via Lexicon

5. Delete and Add again the same project configuration in the Integration Settings Editor a. Workaround is to recreate mapping once the project configuration has been added

back 6. Create a user defined property without a caption in AVEVA Electrical and include this in a

mapping a. Workaround is to ensure that all user defined properties has captions defined