power milling chucks · milling, drilling, threading. pmcs design uses a nut and a needle bearing...

POWER MILLING

CHUCKS

TOOLINGSYSTEMS

1

Guide – Workpiece side types

Main benefitsEase of use, flexibility (by using reduction sleeves) and high transmittable torque are the main advantages of PMC’s tool holding technology. PMC are an additional holder type for cylindrical tool shanks, generating higher clamping torques vs. existing most performant Seco solutions like Strong Shrinkfit holder, and Strong Hydraulic chucks (which have their complementary advantages of precision).

PMCs can hold all type of tools with cylindrical shank (Weldon and Whistle-Notch with limitations). Their high clamping force and high run-out precision are suitable for rough to finishing machining operation, eg. milling, drilling, threading.

PMCs design uses a nut and a needle bearing acting on the small tapered external diameter of chuck’s body, generating extremely high clamping power onto the tool shank, with the advantage to require low tightening torque. Easy to use: just tighten the nut until his face presses onto chuck’s body: Other advises, see the complete operating instructions delivered with each chuck.

Range

- PMC machine sides (spindle interfaces): HSK-A; Seco-CaptoTM; DIN; BT and BT Taper-Face; Ansi and Ansi Taper-Face.- Workpiece sides (tool shank sizes and types):• Direct chuck clamping:

- plain cylindrical diameters 20 mm & 32 mm and 0,750” & 1,25”- Weldon diameter 20 mm and 0.750”

• Reduction sleeves clamping: - plain cylindrical: diameters 6 mm to 25 mm and 0,250” to 1,000”.- Weldon: diameters 6 mm to 25 mm and 0,250” to 1,000”.- Whistle-Notch: diameters 6 mm to 25 mm and 0,250” to 1,000”.

• Note: Suitable tools shanks diameters tolerance: maxi h6.

Product featuresTransmittable torque:Minimum transmittable static torque to the tool shank (Nm) : Chucks diameters 20 mm and 0,750”: 640 N.m (472 Lb.ft).Chucks diameters 32 mm and 1,25”: 1500 N.m (1106 Lb.ft).

Run-out:Maximum run-out, at a gauge projection of 3x ØDCBN-DCBX in relation to chuck’s machine side taper:- Direct chuck clamping: maximum 5 μm.- Reduction sleeves clamping: maximum 10 μm.

Balancing quality:- Pre-balanced by design: also noticed in Product pages ‘Balancing column’.- Can be fine balanced to G6.3 on request, please enquire.

Maximum Rpm:- Chucks diameters 20 mm and 0,750”: 15 000 Rpm maxi.- Chucks diameters 32 mm and 1,25”: 10 000 Rpm maxi.

Power milling chucks (PMC)

2

Stop end screws:Chucks with DIN, BT, BT TF, Ansi, Ansi TF machine sides are delivered with a stop screw fitted (no stop screw in HSK nor Seco-Capto types due to lack of space), allowing fast interchange of tools.

Through coolant features and through coolant stop end screwsPMC are designed for through coolant:- For tools without coolant through channel(s):• Direct chuck clamping: coolant flows through the grooves in chuck’s bore, along tool. • Reduction sleeve clamping: coolant flows through sleeve’s slots along tool.• In the case of chucks delivered with a stop screw, best is to screw back or remove the

screw in order to allow reliable coolant flow between screw and tool (if screw is in contact with tool, only few coolant leakage will flow).

- For tools with coolant through channels: For reliable tool through coolant, use a ‘Stop screws for though coolant’, available as accessories: their tapered workpiece side seals the contact screw / tool shank therewith forcing coolant through tool’s coolant channel(s). Screws are screwed or click-fitted into chuck’s front. Select the suitable screw according to chuck, or chuck and reduction sleeve used with the ‘Stop screws for though coolant’ selection chart in the Product pages.

PMC delivery contents- Extractor for sleeves: also available as Spare parts.- Chucks with DIN, BT, BT TF, Ansi, Ansi TF machine sides are delivered with a stop screw fitted: also available as Spare parts (no stop screw in HSK nor Seco-Capto due to lack of space).- Operating instruction.- Note: reduction sleeves are delivered without additional content.

Guide – Workpiece side types

3

HSK-A Tool holders

EPB PMC – Power milling chucks HSK-A/ ISO12164-1-HSK-A

• Run-out 5µm maximum at 3x ØDCBN-DCBX (10µm with

reduction sleeve)

• Nominal clamping diameter only (no clamping range): tool

shank tolerance h6 maximum

Machine side Workpiece side

Designation

Dimensions in mm

RFID

hole BalancingTaper

DCBN-DCBX

mm LPR LB CBDP BD1 OAL

HSK-A6320 HSKA63-PMC20-085 85,0 59,0 60,0 49.0 117,0 1 PB 1,2

32 HSKA63-PMC32-105 105,0 79,0 80,0 67.0 137,0 1 PB 2,0

HSK-A10020 HSKA100-PMC20-095 100,0 66,0 60,0 49.0 145,0 1 PB 2,8

32 HSKA100-PMC32-110 81,0 80,0 68.0 160,0 1 PB 3,1

HSK-A12532 HSKA125-PMC32-120 125,0 91,0 80,0 68.0 183,0 1 PB 5,3

For reduction sleeves, see page(s) 12-15. For ‘Stop screws for through coolant’, see page(s) 16-17.

Please check availability in current price and stock-list

For HSK sealing plugs, coolant tubes and tube spanners, see MN Tooling Systems.

For

DCBN-DCBX

Spanner

20 03BPMC20

32 03BPMC32

Accessories

For

DCBN-DCBX

Extractor for reduction sleeves

20 03EXTPMC

32 03EXTPMC

Spare Parts

4

HSK-A Tool holders

EPB PMC – Power milling chucks HSK-A/ ISO12164-1-HSK-A


reduction sleeve)




Designation

Dimensions in inch

RFID

hole BalancingTaper

DCBN-DCBX

inch LPR LB CBDP BD1 OAL

HSK-A630,750 HSKA63-PMC0.750-3.500 3,50 2,47 2,36 1,93 4,76 1 PB 3,08

1,250 HSKA63-PMC1.250-4.250 4,25 3,22 3,15 2,64 5,51 1 PB 4,62

HSK-A1000,750 HSKA100-PMC0.750-3.750 3,75 2,60 2,36 1,93 5,71 1 PB 6,17

1,250 HSKA100-PMC1.250-4.500 4,50 3,35 3,15 2,68 6,46 1 PB 8,37

HSK-A1251,250 HSKA125-PMC1.250-4.750 4,75 3,60 3,15 2,68 7,32 1 PB 11,68



For HSK sealing plugs, coolant tubes and tube spanners, see MN Tooling Systems.

For

DCBN-DCBX

Spanner

0,750” 03BPMC20

1,250” 03BPMC32

Accessories

For

DCBN-DCBX


0,750” 03EXTPMC

1,250” 03EXTPMC

Spare Parts

5

DIN 69871 Tool holders

EPB PMC – Power milling chucks DIN 69871-ADB


reduction sleeve)



Machine side Workpiece

side

Designation

Dimensions in mm

KWW TDZ

RFID

hole

Balan-

cingTaper

DCBN-

DCBX mm LPR LB CBDP BD1 OAL LFN-LF

DIN40 ADB20 DIN40ADB-PMC20-060 60,0 40,9 63,0 49.0 128,4 -3-2 8 M16 1 PB 1,1

32 DIN40ADB-PMC32-095 95,0 75,9 80,0 67.0 163,4 15-20 8 M16 1 PB 1,6

DIN50 ADB20 DIN50ADB-PMC20-080 80,0 60,9 63,0 49.0 181,8 17-22 8 M16 1 PB 2,3

32 DIN50ADB-PMC32-075 75,0 56,0 80,0 68.0 176,8 -15--10 8 M16 1 PB 2,8



For Taper/

DCBN-DCBX

Spanner

DIN40/ 20 03BPMC20

DIN40/ 32 03BPMC32

DIN50/ 20 03BPMC20

DIN50/ 32 03BPMC32

Accessories

For Taper/

DCBN-DCBX

Extractor for reduction sleeves Plug Stop screw

DIN40/ 20 03EXTPMC 950A0406 19BEPMC01




Spare Parts

Spare parts:

1 = Stop screw

6

CAT Tool holders

EPB PMC – Power milling chucks CAT-ADB (Ansi Y1994: nominal recess diameters)


reduction sleeve)




side

Designation

Dimensions in inch

KWW TDZ Design

RFID

hole

Balan-

cingTaper

DCBN-

DCBX inch LPR LB CBDP BD1 BD2 OAL LFN-LF

CAT40 ADB0,750 CAT40ADB-PMC0.750-3.000 3,00 2,25 2,48 1,93 1,75 7,32 0,52-0,71 5/16 UNC 5/8”-11 2 1 PB 5,35

1,250 CAT40ADB-PMC1.250-4.250 4,25 3,49 3,54 2,64 1,75 5,69 1,10-1,29 5/16 UNC 5/8”-11 2 1 PB 7,78

CAT50 ADB0,750 CAT50ADB-PMC0.750-3.000 3,00 1,56 2,48 2,75 2,75 6,94 0,52-0,71 5/16 UNC 5/8”-11 1 1 PB 11,17

1,250 CAT50ADB-PMC1.250-3.250 3,25 2,50 3,54 2,75 2,75 1,56 0,10-0,29 5/16 UNC 5/8”-11 1 1 PB 13,60



For Taper/

DCBN-DCBX

Spanner

CAT40/ 0,750” 03BPMC20

CAT40/ 1,250” 03BPMC32

CAT50/ 0,750” 03BPMC20

CAT50/ 1,250” 03BPMC32

Accessories

For Taper/

DCBN-DCBX


CAT40/ 0,750” 03EXTPMC 950A0406 19BEPMC02




Spare Parts

Spare parts:

1 = Stop screw

Design 2Design 1

7

CAT Tool holders

EPB PMC – Power milling chucks CAT Taper-Face-ADB (nominal recess diameters from Ansi Y1994 )


reduction sleeve)




side

Designation

Dimensions in inch

KWW TDZ

De-

sign

RFID

hole

Balan-

cingTaper

DCBN-

DCBX inch LPR LB CBDP BD1 BD2 OAL LFN-LF

CAT TF40 ADB0,750 CAT40TFADB-PMC0.750-3.000 3,00 2,25 2,48 1,93 1,75 5,69 0,52-0,71 5/16 UNC 5/8"-11 2 1 PB 5,35

1,250 CAT40TFADB-PMC1.250-4.250 4,25 1,56 3,54 2,64 1,75 6,94 1,10-1,29 5/16 UNC 5/8"-11 2 1 PB 11,17

CAT TF50 ADB1,250 CAT50TFADB-PMC1.250-3.250 3,25 2,50 3,54 2,75 2,75 7,25 0,10-0,19 5/16 UNC 5/8”-11 1 1 PB 13,60



For Taper/

DCBN-DCBX

Spanner

CAT TF40/ 0,750” 03BPMC20

CAT TF40/ 1,250” 03BPMC32

CAT TF50/ 0,750” 03BPMC20

CAT TF50/ 1,250” 03BPMC32

Accessories

For Taper/

DCBN-DCBX


CAT TF40/ 0,750” 03EXTPMC 950A0406 19BEPMC02




Spare Parts

Spare parts:

1 = Stop screw

Design 2Design 1

8

BT JIS Tool holders

EPB PMC – Power milling chucks BT JIS B 6339-ADB


reduction sleeve)




For Taper/

DCBN-DCBX

Spanner

BT40/ 20 03BPMC20

BT40/ 32 03BPMC32

BT50/ 20 03BPMC20

BT50/ 32 03BPMC32

Accessories

For Taper/

DCBN-DCBX


BT40/ 20 03EXTPMC 950A0406 19BEPMC01

BT40/ 32 03EXTPMC 950A0406 19BEPMC01

BT50/ 20 03EXTPMC 950A0606 19BEPMC01

BT50/ 32 03EXTPMC 950A0606 19BEPMC01

Spare Parts


side

Designation *

Dimensions in mm

KWW TDZ

RFID

hole

Balan-

cingTaper

DCBN-


BT40 ADB20 BT40ADB-PMC20-065 * 65,0 36,5 63,0 49.0 128,4 0-5 8 M16 1 PB 1,3

32 BT40ADB-PMC32-090 90,0 - 90,0 67.0 155,4 10-15 8 M16 1 PB 2,1

BT50 ADB20 BT50ADB-PMC20-085 85,0 47,0 85,0 49.0 186,8 22-27 8 M16 1 PB 3,7

32 BT50ADB-PMC32-095 95,0 57,0 95,0 67.0 196,8 5-10 8 M16 1 PB 4,4

* Item BT40ADB-PMC20-065 shown here is part of the standard range indeed, but could not be shown in the complete Seco catalogue TOOLING SYSTEMS 2018.2

due to process issues. For reduction sleeves, see page(s) 12-15. For ‘Stop screws for through coolant’, see page(s) 16-17.

Spare parts:

1 = Stop screw

9

BT JIS Taper-Face Tool holders

EPB PMC – Power milling chucks BT Taper-Face-ADB


reduction sleeve)




For Taper/

DCBN-DCBX

Spanner

BT TF40/ 20 03BPMC20




Accessories

For Taper/

DCBN-DCBX


BT TF40/ 20 03EXTPMC 950A0406 19BEPMC01




Spare Parts


side

Designation *

Dimensions in mm

KWW TDZ

RFID

hole

Balan-

cingTaper

DCBN-


BT TF40 ADB20 BT40TFADB-PMC20-065 * 65,0 35,5 63,0 49.0 128,4 0-5 8 M16 1 PB 1,3

32 BT40TFADB-PMC32-090 90,0 - 80,0 67.0 155,4 10-15 8 M16 1 PB 2,1

BT TF50 ADB20 BT50TFADB-PMC20-085 85,0 47,0 63,0 49.0 186,8 22-27 8 M16 1 PB 3,7

32 BT50TFADB-PMC32-095 95,0 57,0 80,0 67.0 196,8 5-10 8 M16 1 PB 4,4

* Item BT40TFADB-PMC20-065 shown here is part of the standard range indeed, but could not be shown in the complete Seco catalogue TOOLING SYSTEMS 2018.2

due to process issues. For reduction sleeves, see page(s) 12-15. For ‘Stop screws for through coolant’, see page(s) 16-17.

Spare parts:

1 = Stop screw

10

SecoCaptoTM Tool holders

EPB PMC – Power milling chucks Seco-Capto™


reduction sleeve)




Designation

Dimensions in mm

RFID

hole BalancingTaper

DCBN-DCBX

mm LPR LB CBDP BD1 OAL

C620 C6-PMC20-080 80,0 58,0 60,0 49.0 118,0 1 PB 1,3

32 C6-PMC32-100 100,0 - 80,0 67.0 138,0 1 PB 2,1

C820 C8-PMC20-080 80,0 50,0 60,0 49.0 128,0 1 PB 3,7

32 C8-PMC32-100 100,0 70,0 80,0 67.0 148,0 1 PB 4,4



For

DCBN-DCBX

Spanner

20 03BPMC20

32 03BPMC32

Accessories

For

DCBN-DCBX


20 03EXTPMC

32 03EXTPMC

Spare Parts

11

Main benefitsKnowing that Power milling chucks (PMC) are available in only few diameters: reduction sleeves for PMC allow to clamp several tool shank diameters and types into a same chuck.These reduction sleeves are specific for PMC, as different in dimensions and tolerances from existing reduction sleeves, eg. the ones for Hydraulic chucks.

Range

Reduction sleeves for PMC available sizes: see Product pages; summarized below:• Machine sides (external diameters): diameters 20 mm & 32 mm and 0,750 inch & 1,25 inch.• Workpiece sides (internal diameters): diameters 6 to 25 mm and 0,25 to 1 inch.• Types (Machine side to Workpiece side): metric to metric; metric to inch; inch to inch; inch to metric.- Note: Tools shanks diameters tolerance: maxi h6.- Acceptable tools shanks types, see below:

Product features

Transmittable torque:For a same tool shank diameter, the transmittable torque with reduction sleeve is at least equivalent or higher compared to a direct chuck clamp-ing: as a result of using a bigger chuck. As bigger the chuck used, as bigger the transmittable torque.

Run-out:For chuck with reduction sleeve: Maximum run-out, at a gauge projection of 3x ØDCBN-DCBX (tool shank diameter) in relation to chuck’s machine side taper: maximum 10 μm.Note : Direct chuck clamping: maximum 5 μm.

Through coolant featuresReduction sleeves are designed for through coolant:- For tools without coolant through channels: coolant flows through sleeve’s slots along tool.- Note : For tools with coolant through channels: for reliable tool through coolant, use ‘Stop screws for though coolant’, available as chucks acces-sories: See PMC Guide pages.

Reduction sleeves delivery content- Reduction sleeves are delivered without additional content- Note: One extractor for sleeves and one operating instruction are part of chucks delivery contents.

Operating & setting accessories – Guide

Reduction sleeves for Power milling chucks

Ø 6 - 25 mm

0.250 - 1.0 inch

Ø 6 - 20 mm

0.250 - 0.750 inch

Ø 25 mm

1.0 inch

Ø 6 - 25 mm

0.250 - 1.0 inch

Cylindrical

OK

Weldon

OK

Weldon

OK

Whistle Notch

OK

12

Operating & setting accessories


• Run-out 10 μm maximum at 3 x ØDCB for chuck with sleeve

• Nominal clamping diameter only (no clamping range): tool shank tolerance h6 maximum

Machine

sideWorkpiece

side

Designation

Dimensions in mm

DCON

mmDCB

mm LS FLGT DF LSC

206 05FPMC2006 47,5 2,5 24,0 308 05FPMC2008 47,5 2,5 24,0 3210 05FPMC2010 47,5 2,5 24,0 3512 05FPMC2012 47,5 2,5 24,0 3514 05FPMC2014 47,5 2,5 24,0 3516 05FPMC2016 47,5 2,5 24,0 40

3210 05FPMC3210 60,5 2,5 36 3512 05FPMC3212 60,5 2,5 36 4014 05FPMC3214 60,5 2,5 36 4016 05FPMC3216 60,5 2,5 36 4018 05FPMC3218 60,5 2,5 36 4420 05FPMC3220 60,5 2,5 36 4425 05FPMC3225 60,5 2,5 36 48


13





Machine

sideWorkpiece

side

Designation

Dimensions in inch

DCON

mmDCB

inch LS FLGT DF LSC

200,250 05FPMC200250 1,87 0,09 0,94 1,180,375 05FPMC200375 1,87 0,09 0,94 1,370,500 05FPMC200500 1,87 0,09 0,94 1,370,625 05FPMC200625 1,87 0,09 0,94 1,57

320,375 05FPMC320375 2,38 0,09 1,41 1,370,500 05FPMC320500 2,38 0,09 1,41 1,570,625 05FPMC320625 2,38 0,09 1,41 1,570,750 05FPMC320750 2,38 0,09 1,41 1,731,000 05FPMC321000 2,38 0,09 1,41 1,88


14





Machine

sideWorkpiece

side

Designation

Dimensions in inch

DCON

inchDCB

mm LS FLGT DF LSC

0,7506 05FPMC075006 1,87 0,09 0,94 1,188 05FPMC075008 1,87 0,09 0,94 1,2510 05FPMC075010 1,87 0,09 0,94 1,3712 05FPMC075012 1,87 0,09 0,94 1,3716 05FPMC075016 1,87 0,94 1,57

1,25010 05FPMC125010 2,38 0,09 1,41 1,3712 05FPMC125012 2,38 0,09 1,41 1,5716 05FPMC125016 2,38 0,09 1,41 1,5718 05FPMC125018 2,38 0,09 1,41 1,7320 05FPMC125020 2,38 0,09 1,41 1,7325 05FPMC125025 2,38 0,09 1,41 1,88


15





Machine

sideWorkpiece

side

Designation

Dimensions in inch

DCON

inchDCB

inch LS FLGT DF LSC

0,7500,250 05FPMC07500250 1,87 0,09 0,94 1,180,375 05FPMC07500375 1,87 0,09 0,94 1,370,500 05FPMC07500500 1,87 0,09 0,94 1,370,625 05FPMC07500625 1,87 0,09 0,94 1,57

1,2500,375 05FPMC12500375 2,38 0,09 1,41 1,370,500 05FPMC12500500 2,38 0,09 1,41 1,570,625 05FPMC12500625 2,38 0,09 1,41 1,570,750 05FPMC12500750 2,38 0,09 1,41 1,731,000 05FPMC12501000 2,38 0,09 1,41 1,88


16


Stop screws for through coolant, for Power milling chucks

• For reliable coolant flow for tools with coolant through channel(s).

• Select the suitable screw in the ‘Stop screws for through coolant’ selection chart.

Design 2Design 1

Workpiece

side

Designation

Dimensions in mm

CNT DesignDCBN-DCBX

mm OAL BD1 WF

6-12 19BPMC2001A 21,5 20 4 - 214-20 19BPMC2001B 18 20 4 - 26-12 19BPMC2002A 35,5 - 4 M16 114-20 19BPMC2002B 27,5 - 4 M16 1

6-12 19BPMC3201A 37,5 32 4 - 214-20 19BPMC3201B 31 32 4 - 225-32 19BPMC3201C 28,5 32 4 - 26-12 19BPMC3203A 55,5 - 4 M16 114-20 19BPMC3203B 52 - 4 M16 125-32 19BPMC3203C 37,5 - 4 M16 16-12 19BPMC3204A 77,5 - 4 M16 114-20 19BPMC3204B 74 - 4 M16 125-32 19BPMC3204C 58,5 - 4 M16 1


17


Accessories, stop screws for through coolant for PMC holders

• For reliable coolant flow for tools with coolant through channel(s).

• Select the suitable screw in the ‘Stop screws for though coolant’ selection chart.

Design 2Design 1

Workpiece

side

Designation

Dimensions in inch

CNT DesignDCBN-DCBX

inch OAL BD1 WF

1/4" - 7/16” 19BPMC190505D 0,84 0,74 0,15 - 21/2" - 3/4” 19BPMC190505E 0,70 0,74 0,15 - 21/4" - 7/16” 19BPMC190506D 1,39 - 0,15 UNF 5/8"-18 11/2" - 3/4” 19BPMC190506E 1,08 - 0,15 UNF 5/8"-18 1

3/8" - 1/2” 19BPMC317505F 1,25 1,25 0,15 - 25/8" - 3/4” 19BPMC317505G 1,22 - 0,15 M16 11" - 1-1/4” 19BPMC317505H 1,12 1,25 0,15 - 23/8" - 1/2” 19BPMC317506F 1,94 - 0,15 UNF 5/8"-18 15/8" - 3/4” 19BPMC317506G 1,90 - 0,15 UNF 5/8"-18 11" - 1-1/4” 19BPMC317506H 1,35 - 0,15 UNF 5/8"-18 1


18

For Power milling chuck

For tool shank Ø mm/inch Reduction sleeves

Stop screw for coolant through,

DesignationDesignation Machine side

Workpiece side Ø (clamping bore)

mm/inch

HSKA63-PMC20-085 HSK-A63 20

6 05FPMC2006 19BPMC2001A8 05FPMC2008 19BPMC2001A

10 05FPMC2010 19BPMC2001A12 05FPMC2012 19BPMC2001A14 05FPMC2014 19BPMC2001B16 05FPMC2016 19BPMC2001B18 - 19BPMC2001B

0,250 05FPMC200250 19BPMC2001A0,375 05FPMC200375 19BPMC2001A0,500 05FPMC200500 19BPMC2001B0,625 05FPMC200625 19BPMC2001B

HSKA63-PMC32-105 HSK-A63 32

10 05FPMC3210 19BPMC3201A12 05FPMC3212 19BPMC3201A14 05FPMC3214 19BPMC3201B16 05FPMC3216 19BPMC3201B18 05FPMC3218 19BPMC3201B20 05FPMC3220 19BPMC3201B25 05FPMC3225 19BPMC3201C32 - 19BPMC3201C

0,375 05FPMC320375 19BPMC3201A0,500 05FPMC320500 19BPMC3201B0,625 05FPMC320625 19BPMC3201B0,750 05FPMC320750 19BPMC3201B1,000 05FPMC321000 19BPMC3201C

HSKA100-PMC20-095 HSK-A100 20




HSKA100-PMC32-110 HSK-A100 32



Selection chart for Stop screws for coolant through, for Power milling chucks: selection is according to chuck used and tool shank diameter.

Please check availability in current price and stock-listNote: the sign (-) in the Reduction sleeves column means a direct chuck / tool clamping situation.


19






mm/inch

HSKA125-PMC32-120 HSK-A125 32



DIN40ADB-PMC20-060 DIN40 ADB 20














20






mm/inch




BT40ADB-PMC20-063 BT40 ADB 20














21






mm/inch




BT40TFADB-PMC20-063 BT TF40 ADB 20














22






mm/inch




C6-PMC20-080 C6 20




C6-PMC32-100 C6 32



C8-PMC20-080 C8 20







23






mm/inch

C8-PMC32-100 C8 32



HSKA63-PMC0.750-3.500 HSK-A63 0,750

6 05FPMC075006 19BPMC190505D8 05FPMC075008 19BPMC190505D10 05FPMC075010 19BPMC190505D12 05FPMC075012 19BPMC190505D16 05FPMC075016 19BPMC190505D

0,250 05FPMC07500250 19BPMC190505D0,375 05FPMC07500375 19BPMC190505D0,500 05FPMC07500500 19BPMC190505E0,625 05FPMC07500625 19BPMC190505E0,750 - 19BPMC190505E

HSKA63-PMC1.250-4.250 HSK-A63 1,250

10 05FPMC125010 19BPMC317505F12 05FPMC125012 19BPMC317505G16 05FPMC125016 19BPMC317505G18 05FPMC125018 19BPMC317505H20 05FPMC125020 19BPMC317505H25 05FPMC125025 19BPMC317505H

0,375 05FPMC12500375 19BPMC317505F0,500 05FPMC12500500 19BPMC317505F0,625 05FPMC12500625 19BPMC317505G0,750 05FPMC12500750 19BPMC317505G1,000 05FPMC12501000 19BPMC317505H1,250 - 19BPMC317505H

HSKA100-PMC0.750-3.750 HSK-A100 0.750

6 05FPMC075006 19BPMC190505D8 05FPMC075008 19BPMC190505D10 05FPMC075010 19BPMC190505E12 05FPMC075012 19BPMC190505E16 05FPMC075016 19BPMC190505E





24






mm/inch

HSKA100-PMC1.250-4.500

10 05FPMC125010 19BPMC317505F12 05FPMC125012 19BPMC317505G16 05FPMC125016 19BPMC317505G18 05FPMC125018 19BPMC317505H20 05FPMC125020 19BPMC317505H

HSK-A100 1,250 25 05FPMC125025 19BPMC317505H0,375 05FPMC12500375 19BPMC317505F0,500 05FPMC12500500 19BPMC317505F0,625 05FPMC12500625 19BPMC317505G0,750 05FPMC12500750 19BPMC317505G1,000 05FPMC12501000 19BPMC317505H1,250 - 19BPMC317505H

HSKA125-PMC1.250-4.750 HSK-A125 1,250

10 05FPMC125010 19BPMC317505F12 05FPMC125012 19BPMC317505G16 05FPMC125016 19BPMC317505G18 05FPMC125018 19BPMC317505H20 05FPMC125020 19BPMC317505H25 05FPMC125025 19BPMC317505H


CAT40ADB-PMC0.750-3.000 CAT 40ADB 0,750

6 05FPMC075006 19BPMC190506D8 05FPMC075008 19BPMC190506D

10 05FPMC075010 19BPMC190506E12 05FPMC075012 19BPMC190506E16 05FPMC075016 19BPMC190506E


CAT40ADB-PMC1.250-4.250 CAT 40ADB 1,250

10 05FPMC125010 19BPMC317506G12 05FPMC125012 19BPMC317506G16 05FPMC125016 19BPMC317506H18 05FPMC125018 19BPMC317506H20 05FPMC125020 19BPMC317506H25 05FPMC125025 19BPMC317506H





25






mm/inch

CAT50ADB-PMC0.750-3.000 CAT50 ADB 0,750




CAT50ADB-PMC1.250-3.250

10 05FPMC125010 19BPMC317506G12 05FPMC125012 19BPMC317506G16 05FPMC125016 19BPMC317506H18 05FPMC125018 19BPMC317506H20 05FPMC125020 19BPMC317506H

CAT50 ADB 1,250 25 05FPMC125025 19BPMC317506H0,375 05FPMC12500375 19BPMC317506F0,500 05FPMC12500500 19BPMC317506F0,625 05FPMC12500625 19BPMC317506G0,750 05FPMC12500750 19BPMC317506G1,000 05FPMC12501000 19BPMC317506H1,250 - 19BPMC317506H

CAT40TFADB-PMC0.750-3.000 CAT TF40 ADB 0,750













Seco-EPB

8 B RUE DE NEUWILLER

F-67330 BOUXWILLER

FRANCE

Phone: +33 (0)3 88 71 38 89

WWW.SECOTOOLS.COM

60PMCP01, © SECO TOOLS AB, 2018. All rights

reserved. Technical specifi cations are subject to

change without notice.

power milling chucks · milling, drilling, threading. pmcs design uses a nut and a needle bearing...

Documents