Population Forecasting usingGeometric Increase Method

Presented by:Bhantooa Luvindraj (1014582)Boyjoo Manoj (1014504)Bundhoo Deepshika (1017841)Ramgoolam Oomeshnathsingh (1019085)Seburn Indra (1015380)

Population Forecasting consists of mathematical models which are used to analyse changes in population numbers. There are several factors affecting changes in population: Increase due to births Decrease due to deaths Increase/Decrease due to migration Increase due to annexation All the above data can be obtained from the census population records.In Mauritius, these information can be obtained at the Central Statistics Office (CSO)

Population Forecasting

The various mathematical methods available are generally classified in two categories: Short term methods and Long term methods

Short term methods (1-10 years) Arithmetic progression Geometric progression Incremental increase method Decreasing rate of growth Simple graphical method

Long term methods (10-50 years) Comparative graphical method Ratio method Logistic curve method

…Population Forecasting

Population forecasting is an integral part of design. It is essential to take into account the population at the end of the design period.

Fundamental to planning (Assumptions and estimates used in determining sewage flow have a permanent effect on planning decisions and outcomes)

Premature and excessive investments in works

System failure and hence increasing customer complaints

Environmental impact

Essential to service provider so as to know the spare capacity of the system

Identification of weak links of systemAbility to accept new/unexpected demands

Why is population forecasting important?

Projections are likely to be carried out for the design of a system. A service provider should have knowledge of current demand/flow and anticipated future projections at all times.

Projections should be determined: Once the needs of the service are already known and the objectives

determined

Stakeholder requirements have been identified

Adequate raw data on existing flows/demands is available

When can projections be carried out?

The basic model for geometric change in population size is:

P = Po λt

which is based on the hypothesis that rate of change of population is proportional to the population. According to this, method it is assumed that the rate of increase of population growth in a community is proportional to the present population.

Po denotes initial size, P denotes population at time t t denotes time (measured in decades) λ is the ‘finite population multiplier’ which can be interpreted as λ = ℮i for

continuous change or λ = 1+ i for discrete (constant) ‘compound interest’ or ‘birth-pulse’ populations.

Geometric Increase Method

Example

Predict the population for the years 2023, 2033, and 2043 from the following census figures of a town using geometric method.

Year 1943 1953 1963 1973 1983 1993 2003 2013

Population: (thousands)

60 65 63 72 79 89 97 120

P = Poλt

λ = (1+ i) for discrete change Therefore P = Po (1+i)t where, P0 : Initial population size P: Population size at time t i: Average percentage increase per decade t: Number of decades

Solution

1. USING DISCRETE METHOD (RATE OF CHANGE IS CONSTANT)

Year Population: (thousands)

Increment per Decade

Percentage Increment per Decade

1943 60 - -

1953 65 +5 (5÷60) x 100 = +8.33

1963 63 -2 (2÷65) x 100 = -3.07

1973 72 +9 (9÷63) x 100 = +14.28

1983 79 +7 (7÷72) x 100 = +9.72

1993 89 +10 (10÷79) x 100 = +12.66

2003 97 +8 (8÷89) x 100 = +8.98

2013 120 +23 (23÷97) x 100 = +23.71

Net values - +60 +74.61

Averages - 8.57 10.66

…Solution (using discrete method)

Population for 2023 = Population 2013 x (1+i/100) t

= 120 x (1+10.66/100), where i = 10.66, t = 1= 120 x 110.66/100 = 132.8

Population for 2033 = Population 2013 x (1+i/100) t

= 120 x (1+10.66/100)2, where i = 10.66, t = 2= 120 x 1.2245 = 146.95

Population for 2043 = Population 2013 x (1+i/100) t

= 120 x (1+10.66/100)3, where  i = 10.66, t = 3= 120 x 1.355 = 162.60

…Solution (using discrete method)Solution

(When t = 0, P = Po, therefore c = ln Po)

2. CONTINOUS METHOD (RATE OF CHANGE IS INCREASING)

P = Poλt

λ = ℮ i for continuous change P0 : Initial population size P: Population size at time t i: Average percentage increase per decade t: Number of decades

The average rate of increase ‘i’ is calculated in the same way as for the discrete change.

…Solution (using continuous method)

Population for 2023 = Population 2013 x e it

= 120 x e(10.66/100 *1), where i = 10.66, t = 1= 133.50

   Population for 2033 = Population 2013 x eit

=120 x e(10.66/100 *2), where i = 10.66, t = 2=148.52

Population for 2043 = Population 2013 x e it

=120 x e(10.66/100 *3), where i = 10.66, t = 3= 165.22

…Solution (using continuous method)

Year Forecasted PopulationDiscrete Method Continuous Method

2023 132.80 133.502033 146.95 148.522043 162.60 165.22

…solution (comparison of results)

…solution (comparison of results)

1940 1960 1980 2000 2020 2040 206040

60

80

100

120

140

160

180

Geometric Progression Curve

Discrete Method Continuous Method

…solution (comparison of results)

2020 2025 2030 2035 2040 2045130

135

140

145

150

155

160

165

170

Geometric Progression curve

Discrete Method Continuous Method

In the graph, we can conclude that values obtained from the continuous method are higher than those obtained from the discrete method. This is because in the discrete method, the rate of increase of population is constant whereas the continuous method has an increasing rate of increase of population.

In order to calculate the population number for any other specific year within the decade, the same graph can be used.

…solution (comparison of results)

Geometric extrapolation is desirable for short intervals Simple method When forecasting for a new city Geometric rates are preferable to arithmetic rates for the

extrapolation of decreases in population over a series of years

Advantages of Geometric Progression

When the geometric rate of increase is high and the period of time is long

If the accuracy of the basic census figures is subject to considerable doubt

Where the death rate is declining while the birth rate remains nearly constant

Limitations of Geometric Progression

Quantity of sewage at the end of a design period

= Per capita production of sewage x Forecasted population at the end of the design period

The quantity of wastewater generated per capita is estimated to be 80% of the water consumption per capita.

The water consumption per occupant per day, for different institutions, can be obtained from the table

Population Forecasting in the Design of Waste Water system

…Population Forecasting in the Design of Waste Water system

In the light of the above, we can see that the Geometric Increase Method is a simple realistic population model based on past information. This method tends to give a higher estimate than normal since it behaves exponentially. It more accurately describes the continuous and cumulative nature of population growth. In normal practice, an average of the arithmetic method and geometric method is performed to get a more accurate estimate.

Conclusion

THANK YOU FOR YOUR ATTENTION