polymerisation kinetics
TRANSCRIPT
Polymerisation kineticsMAT5002
Polymerisation kinetics
Thermodynamics
• Tells us where the system would like to go eventually, i.e. it defines relationships between macroscopic variables at equilibrium
Kinetics
• Tells us how fast the system takes various reaction paths
EXAMPLESSUGAR + OXYGEN → PRODUCTS + ENERGY
CRYSTALLISATION IS ALSO A PROCESS CONTROLLED BY KINETICS
2
Polymerisation kinetics
• Step growth SLOW• Can use statistical methods as well as kinetics to describe mol. wt.
distributions
• Chain growth FAST• Can apply statistical methods to an analysis of the microstructure of the
products, but not the polymerisation process and things like mol. wt.
3
Kinetics of step-growth polymerisation
• Why bother?• How long does it take to make polymer ?
• Can we speed up the reaction ?
• What is the relationship between kinetics and the mol. wt. of the product ?
4
Revision
Rate of reaction = constant x [concentration]n terms
Rate of disappearance of monomer = −𝑑𝑀
𝑑𝑡= k x [concentration]n terms
5
Kinetics of polycondensation
• Key assumption – Flory• The reactivity of a functional group is independent of the length of the chain
to which it is attached
• Example: dibasic acid + glycol → polyester
6
Was Flory right?
7
Kinetics of polycondensation
• Kinetic equation for this type of reaction is usually in the form of
• N.B. [A] and [B] are concentrations of functional groups
• However, esterification reactions are acid catalysed and in the absence of added strong acid
8
More kinetics
• If [A] = [B]
• Hence
9
Extent of reaction
• Define p = extent of reaction
• In this example let
• Then
• And
10
Acid catalysed reaction
• Note the concentration of the acid catalyst (a constant) is included in k’
11
Number average degree of polymerisation
12
Kinetics of free radical polymerisation
• We need to consider the following steps;• Initiation
• Propagation
• (chain transfer)
• Termination
13
Initiation
14
Initiation
• Assume decomposition is the rate limiting step, i.e. ki >> kd
• Then we only have to consider kd
• But only a fraction of f radicals initiate chain growth
15
f – efficiency factor
Propagation
• In general
• Assumption: reactivity independent of chain length
16
Termination
Combination Disproportionation
17
Rate of termination
• Where
• Obtained from • Both reactions are 2nd order
• Rate of removal of chain radicals = sum of the 2 termination reactions
18
ktc – combinationktd - disproportionation
Summary
• Problem:• we don’t know [M∙]
• Solution:• Assume steady-state concentration of transient species
19
Steady-state assumption
• [M∙] = constant
• This means that the radicals are consumed at the same rate as they are generated
• ri = rt
20
f – efficiency factor
Rate of propagation
• Rate of propagation = rate of polymerisation
• Substituting
• But [I] is not constant
• From obtain
• So
21
What does this tell us?
1. If we want to increase Rp
increase [M] or [I]
2.
3. Trommsdorff effect
• But changing [I] also changes mol. wt.
• For ethylene at 130 ˚C and 1 bar pressure
• For ethylene at 200 ˚C and 2500 bar pressure
22
Trommsdorff effect (auto-acceleration)
• A dangerous reaction behaviour that can occur in free-radical polymerisation systems. It is due to the localised increases in viscosity of the polymerising system that slow down termination reactions.
• The removal of reaction obstacles causes a rapid increase in the overall rate of reaction, leading to possible reaction runaway and altering the characteristics of the polymers produced.
• Normally, Rp decreases with time because [M] and [I] drop with extent of conversion
23
Conversion
• Definition:
• In initial stages of the reaction we can assume [I]=[I]0 = constant
• Integrating
24
Maximum conversion
• Usually there is a 1st order decay in the initiation concentration
• i.e.
• and
• So conversion =
• Max. conversion t→∞ =
25
Average chain length
• Define kinetic chain length
• This is the average number of monomers polymerised per chain radical at a particular instant of time during the polymerisation reaction
26
Kinetic chain length
• Consider a time period t
• Let us say that1. 100 chains are started
2. 1,000,000 monomers are reacted in this time period
• Then the average degree of polymerisation of these chains is
27
Kinetic chain length
• There WILL be some obvious errors, e.g. what about chains that were initiated but not terminated just before the start of the selected period of time?, but these are less significant with smaller time intervals.
• In the limit of time interval dt
• So
• The degree of polymerisation then depends on termination mechanism
28
Instantaneous number average chain length
• What if the termination occurs by both mechanisms? Define an average number of dead chains per termination reaction
• Hence
29
Chain transfer
• Chain transfer may occur to solvent, added agents, etc.
• Can then obtain
• Or
30
Energetic characteristics
• Activation energies and frequency factors
• Assume that all rate constants (kd, kp, kt) are Arrhenius-like.
A – frequency factorE – activation energy
31
Energetics: rate of polymerisation
This is the key!
Composite activation energy, usually ~ 80-90 kJ mol-1
32
-
Energetics: degree of polymerisation
This is the key!
Overall activation energy
Coupling
33
Temperature dependence of rate of polymerisation and degree of polymerisation
T-1
Rat
e o
f p
oly
mer
isat
ion
Weigh
t-average mo
lecular m
ass
34