pdb saudi split (titan gold plus)

8/10/2019 PDB Saudi Split (Titan Gold Plus)

1/45

60Hz(R22SR-6RMG2-01A

Saudi Arabia

General Wall Mounted


2/45

2 GENERAL WALL MOUNTED

GENERAL WALL MOUNTED

Contents

1. Models Line up .............................................................................6

2. Nomenclature ...............................................................................7

3. Features & Benefits......................................................................8

4. Specifications.............................................................................10

5. Dimensional Drawings...............................................................12

6. Wiring Diagrams.........................................................................14

7. Refrigerant Cycle Diagram ........................................................18

8. Capacity Tables ..........................................................................19

9. Capacity Coefficient factor........................................................21

10. Operation Range ......................................................................22

11. Air Velocity and Temperature Distribution

(Reference Data) .......................................................................23

12. Controller ..................................................................................24

13. Installation ................................................................................25


3/45

3

SR-6RMG2-01A


Test condition of international standard

KSC ISO ARI AHAM AS SSA

9306 5151 210/240 1861.1 385

Indoor

DBC(F) 27.0 27.0 26.7(80) 26.7(80) 27.0 29.0

Cooling WBC(F) 19.5 19.0 19.4(67) 19.4(67) 19.0 19.0

CapacityOutdoor

DBC(F) 35.0 35.0 35.0(95) 35.0(95) 35.0 46.0

WBC(F) 24.0 24.0 23.9(75) 23.9(75) 24.0 24.0

Indoor

DBC(F) 20.0 20.0 21.1(70) 21.1(70) 21.0 21.0

Heating WBC(F) 15.0 15.0 15.6(60) 15.6(60) 15.0 15.5

CapacityOutdoor

DBC(F) 7.0 7.0 8.3(47) 8.3(47) 7.0 7.0

WBC(F) 6.0 6.0 6.1(43) 6.1(43) 6.0 6.0

Indoor

DBC(F) 32.0 32.0 26.7(80) 32.2(90) 32.0 29.0Maximum

WBC(F) 23.0 23.0 19.4(67) 22.8(73) 23.0 19.0Cooling

Outdoor

DBC(F) 43.0 43.0 46.1(115) 43.3(110) 43.0 54.0Operating

WBC(F) 26.0 26.0 23.9(75) 25.6(78) 26.0 24.0

Indoor

DBC(F) 27.0 27.0 26.7(80) 26.7(80) - -Maximum

WBC(F) 19.0 19.0 19.4(67) 22.8(73) - -Heating

Outdoor

DBC(F) 21.0 24.0 23.9(75) 23.9(75) - -Operating

WBC(F) 15.0 18.0 18.3(65) 18.3(65) - -

EnclosureIndoor

DBC(F) 27.0 27.0 26.7(80) 26.7(80) 27.0 27.0

Sweat / WBC(F) 24.0 24.0 23.9(75) 23.9(75) 24.0 24.0

CondensateOutdoor

DBC(F) 27.0 27.0 26.7(80) 26.7(80) 27.0 27.0

Disposal WBC(F) 24.0 24.0 23.9(75) 23.9(75) 24.0 24.0

Freeze-up/ Indoor DBC(F) 21.0 21.0 19.4(67) 21.1(70) 21.0 21.0

Low WBC(F) 15.0 15.0 13.9(57) 15.6(60) 16.0 16.0

Temperature

Outdoor DBC(F) 21.0 21.0 19.4(67) 21.1(70) 21.0 21.0

WBC(F) 15.0 15.0 13.9(57) 15.6(60) 16.0 16.0

KS : Korea Standard AS : Australia Standard

ISO : International Standard Organization SSA : Saudi Arabian StandardARI : Airconditioning and Refrigeration InstituteAHAM : Association of Home Appliance Manufacturers

CLASSIFICATION


4/45

4

SR-6RMG2-01A


General Description

Split type of Air Conditioners are known by the category name of Wall Mounted Type of units.These units can beeasily installed in a small space and have exceptional Cooling capacity.Designed for Low-noise operation,itensures a pleasant air conditioned environment.

LG Offers various types of units to its customers to suit for the best application and requirement.The following are

the important categories offered by LG :1) General Wall Mounted Type Units : Units with Simplicity in design.

2) Art Cool Units : A new concept of cooling introduced by LG in the field of Air Conditioning.

3) New Gas Models : These models uses HCFC free refrigerant to provide a healthy environment to the world.

Some of the Important Features of these units are listed below :

1) Providing Health to the Customers : By having Filters such as Plasma Filter which is capable of removing MicroOrganisms up to 0.1 microns.

2) Long Term Money Saving : By providing Features such as Gold Fin,Plasma Fin, Auto Clean etc. to maintain thesame performance for years.

3) Best Comfort : With Features such as Sleep Mode,Timer,Auto Restart etc.

These Units are available with many standard and optional features which gives our Customers the choice to selectthe unit of their own desire.For details refer to the Detailed specification followed after this description.

LG Electronics Inc.

Air Conditioning & Energy Solution Company


5/45

5

SR-6RMG2-01A


Publication history

PDB No. Product Name Notes Publication in

SR-6RMG2-01A SRAC 4Models Dec. 2012


6/45

6

Models Line up SR-6RMG2-01A


1. Models Line upGeneral Wall Mounted

Edition Capacity Chassis Type Model

#1

18K SCC/O GS-C182C4B2

H/P GS-H182C4B2

24K SCC/O GS-C242C4B2

H/P GS-H242C4B2


7/45

7

NomenclatureSR-6RMG2-01A


2. Nomenclature Identification Rule

Serial Number

Function

B: 4Way

Look/Color

Chassis NameC: SC

Electric Rating

2: 220V, 60Hz

Capacity

EX) '18' 18,000Btu/h Class

Model Type

C: Cooling Only

H: Heat Pump

Product Type

S: Split

Refrigerant Type

G: R22

Supply Method Diving and Type-: SET

G S C- 81 2 C 4 B 1

Chassis Look Classification

SC 4 ICE-E (White)


8/45

8

Features & Benefits SR-6RMG2-01A


3. Features & Benefits

SmokeAway GoldFin TropicalCompressor

StylishDesign

Quick & EasyInstallation

Skew Fan DualProtection Filter

Vane &Louver

Extreme Durability

The advanced tropical compressor withstandsextreme weather conditions, enabling theproduct to operate despite high outside tem-perature.

By adopting gold plated fins in the exteriorunit, the heat exchanger is protected from cor-rosion and wear from external conditions.

The combination of tropical compressor,and the gold fin in the exterior unit allcontribute in the improved durability of LG airconditioner.


9/45

9

Features & BenefitsSR-6RMG2-01A


Power Cooling

Perfect Health Care

Energy Saving

Stylish Design

Quick & Easy Installation

20m Windblast : Strong and cool windblastcovers the distance of 20m.

Optimized Airflow : The interior of the com-pressor in the outdoor unit has been construct-ed to minimze the sound produced when oper-ating.

The cool airflow reaches thedistance of 15m to all corners ofthe room, keeping the space cooland comfortable regardless ofoutside temperature.

Smoke Away : 3 million ionsspread from diffusion charger and 3M MicroProtection filter remove smoke particle asmuch as air-purifier removes.* Test Results

Size of Area : 30m3, CADR : 135

Dual Protection Filter : Dual Protection Filterinitially captures dust in the air that comes into the air conditioner.

Filter : While being easy to main-tain, the powerful plasma filtration system ofLG air conditioner protects the user from odorand any harmful substances floating in air.

3M Multi Protection Filter : 3M MultiProtection filter captures dust, virus and aller-gen and deactivates the captured virus andallergen by unique technologies of LG and 3M.

Various filtration system protects the userfrom all harmful substances including odor,bacteria, and allergen

Inverter V : The advanced inverter technologyof LG enables the user of the air conditioner touse more and save more.

State of the art heat exchanger, air outlet,compressor, and inverter technology providethe worlds highest energy efficiency

The design of LG air conditioners are stylish ina way that is incomparable to others. Think of

it not just as an air conditioner, but an objetthat will lighten up your living room.

LG air conditioners are not just refreshinglyefficient, but also exceptionally elegant indesign

Perfect finishing / Bigger tubing space / Installationplate improvement / Detachable bottom cover /Elevated service valve / Installation support clip /Compatible with inverter multi system

Installation has never been easier as with thedelicately designed installation elements ofLG air conditioners


10/45

10

Specifications SR-6RMG2-01A


4. SpecificationsGeneral Wall Mounted(#1)

Note:O : Applied, - : No relation* For circuit breaker rating, please conform to local standards wherever necessary.

Some of functions are slightly different depending upon models. The specification may be subject to change without notic for purpose of improvement.

Model Name (LG) GS-C182C4B2 GS-H182C4B2Pet Name Gold Plus Gold Plus

Cooling Capacity (T1)W 5,250 5,130

Btu/h. 17,914 17,504

Heating Capacity (H1)W - 5,250

Btu/h. - 17,914

Power Input NormalCooling W 2,050 2,150Heating W - 1,750

Running Current

(Normal)

Cooling A 9.6 10.0

Heating A - 8.0

EERW/W 2.56 2.39

Btu/h.W 8.74 8.14(STAR) 3 2

COP W/W - 3.00

Power FactorCooling % 97% 98%Heating % - 99%


Btu/h. 15,696 15,184Power Input (T3) W 2,500 2,450Running Current (T3) A 11.5 11.5

EERW/W 1.84 1.82

Btu/h.W 6.28 6.20Power Factor % 98.81 96.84

Power Input (Max)Cooling W 2,900 2,900Heating W - 1,890

Running Current

(Max)Cooling A 13.5 13.5Heating A - 8.9

Power FactorCooling % 97.64 97.64Heating % - 96.53

Power Supply / V / Hz 1/220/60 1/220/60

Air CirculationIndoor m3/min(CFM),Max 13.0 (460) 13.0 (460)Outdoor m3/min(CFM),Max 45 (1,590) 45 (1,590)

Moisture Removal /h. 1.9 1.9

Noise Level(SoundPressure,1m)

IndoordB(A)3,High 43 43dB(A)3,Med 40 40dB(A)3,Low 37 37

Outdoor dB(A)3,Max 56 56

Refrigerant ChargeType R22 R22

g 970 970

Compressor

Type ROTARY ROTARYModel QJ278KCF QJ278KCFMaker LG LGCapacity kcal/h.(Btu/h.) 5,744(19,600) 5,744(19,600)Motor Type PSC PSCMotor Input W 1,867 1,867Oil Type SUNISO 4GSI or NOC NM56 SUNISO 4GSI or NOC NM56Oil Charge cc 500 500O.L.P Name INTERNAL INTERNAL

Blower MotorType Cross Flow Fan Cross Flow FanOutput W 22 22

Fan MotorType Axial fan Axial fanMotor Type AC Induction AC InductionMotor Output W 64 64

Circuit Breaker A 20 20Power Cord AWG#:P*mm2 3x1.5 3x2.0Connecting Cable AWG#:P*mm2 3x1.5 3x2.0+2x0.75

Connecting Tube(. Socket Flare)

Liquid Side mm(in) 6.35(1/4") 6.35(1/4")Gas Side mm(in) 15.88(5/8") 15.88(5/8")Length,std m(in) 5(196) 5(196)

Drain Hose (O.D , I.D) mm(in) 21.5,16 (0.85,0.63) 21.5,16 (0.85,0.63)

Dimension

Indoor

(W*H*D)mm 1030*320*245 1030*320*245inch 40.5*12.6*9.6 40.5*12.6*9.6

Outdoor(W*H*D)

mm 870*655*320 870*655*320inch 34.25*25.79*12.6 34.25*25.79*12.6

Net WeightIndoor kg(lbs) 12.6(27.8) 13(28.7)Outdoor kg(lbs) 40.5(89.3) 42(92.6)

Stuffing Quantity In+Out 20/40ft/HC/Truck 57/124/139/- 57/124/139/-Tool Code In+Out SC+UE SC+UE

Functions

Air flow

Air supply outlet 1 1Airflow direction control(left & right) Auto AutoAirflow direction control(up & down) Auto AutoAuto swing(left & right) Auto AutoAuto swing(up & down) Auto AutoAirflow steps(fan/cool/heat) 3/4/- 3/4/3Chaos swing Yes YesChaos wind(auto wind) Yes YesJet cool(Power wind) Yes Yes

Air purifyingDeodorizing filter (Allergy & H1N1 Filter) - -Plasma air purifier - -

Prefilter(washable / anti-fungus) Yes Yes

ReliabilityHot start - YesSelf diagnosis Yes YesSoft dry operation Yes Yes

Convenience

Setting Temperature, Cooling 18 - 30 18 - 30Setting Temperature, Heating - 16 - 30Auto changeover - YesAuto cleaning Yes YesAuto operation(artificial intelligence) Yes -Auto restart operation Yes YesForced operation Yes YesSleep mode Yes YesSetting Temperature Range (Cooling) 18-30 18-30Setting Temperature Range (Heating) 16-30 16-30Temperature Increment 1 1Timer(Hr) Yes (24h On/Off) Yes (24h On/Off)

Individual

controlWireless remote controller(simple) - -Wireless LCD remote control Yes Yes


11/45

11

SpecificationsSR-6RMG2-01A


Note:O : Applied, - : No relation* For circuit breaker rating, please conform to local standards wherever necessary.

Some of functions are slightly different depending upon models. The specification may be subject to change without notic for purpose of improvement.

Model Name (LG) GS-C242C4B2 GS-H242C4B2Pet Name Gold Plus Gold Plus


Btu/h. 22,520 22,520

Heating Capacity (H1)W - 6,700

Btu/h. - 22,861

Power Input NormalCooling W 2,650 2,650Heating W - 2,500

Running Current

(Normal)

Cooling A 12.6 12.6

Heating A - 12.0

EERW/W 2.49 2.49

Btu/h.W 8.50 8.50(STAR) 3.00 3.00

COP W/W - 2.68

Power FactorCooling % 96% 96%Heating % - 95%


Btu/h. 19,620 19,620Power Input (T3) W 3,080 3,080Running Current (T3) A 14.5 14.5

EERW/W

Btu/h.W 6.37 6.37Power Factor % 96.55 96.55

Power Input (Max)Cooling W 4,000 4,000Heating W - 2,900

Running Current

(Max)Cooling A 18.5 18.5Heating A - 14.0

Power FactorCooling % 98.28 98.28Heating % - 94.16

Power Supply / V / Hz 1/220/60 1/220/60

Air CirculationIndoor m3/min(CFM),Max 16.0(566) 16.0(566)Outdoor m3/min(CFM),Max 48 (1,695) 48 (1,695)

Moisture Removal /h. 2.5 2.5

Noise Level(SoundPressure,1m)

IndoordB(A)3,High 43 43dB(A)3,Med 40 40dB(A)3,Low 37 37

Outdoor dB(A)3,Max 56 56

Refrigerant ChargeType R22 R22

g 1550 1550

Compressor

Type ROTARY ROTARYModel QP362KBB QP362KBBMaker LG LGCapacity kcal/h.(Btu/h.) 7,911(27,000) 7,911(27,000)Motor Type PSC PSCMotor Input W 2,571 2,571Oil Type NM56 or SUNISO 4GSI NM56 or SUNISO 4GSIOil Charge cc 700 700O.L.P Name INTERNAL INTERNAL

Blower MotorType Cross Flow Fan Cross Flow FanOutput W 25.6 25.6

Fan MotorType Axial fan Axial fanMotor Type AC Induction AC InductionMotor Output W 64 64

Circuit Breaker A 30 30Power Cord AWG#:P*mm2 3x2.5 3x2.5Connecting Cable AWG#:P*mm2 3x2.5 3x2.5+2x0.75

Connecting Tube(. Socket Flare)

Liquid Side mm(in) 9.52(3/8") 9.52(3/8")Gas Side mm(in) 15.88(5/8") 15.88(5/8")Length,std m(in) 5(196) 5(196)

Drain Hose (O.D , I.D) mm(in) 21.5,16 (0.85,0.63) 21.5,16 (0.85,0.63)

Dimension

Indoor

(W*H*D)mm 1030*320*245 1030*320*245inch 40.5*12.6*9.6 40.5*12.6*9.6

Outdoor(W*H*D)

mm 870*655*320 870*655*320inch 34.25*25.79*12.6 34.25*25.79*12.6

Net WeightIndoor kg(lbs) 13.6(30.0) 13.6(30.0)Outdoor kg(lbs) 50,5(111.33) 50,5(111.33)

Stuffing Quantity In+Out 20/40ft/HC/Truck 57/124/139/- 57/124/139/-Tool Code In+Out SC+UE SC+UE

Functions

Air flow

Air supply outlet 1 1Airflow direction control(left & right) Auto AutoAirflow direction control(up & down) Auto AutoAuto swing(left & right) Auto AutoAuto swing(up & down) Auto AutoAirflow steps(fan/cool/heat) 3/4/- 3/4/3Chaos swing Yes YesChaos wind(auto wind) Yes YesJet cool(Power wind) Yes Yes

Air purifyingDeodorizing filter (Allergy & H1N1 Filter) - -Plasma air purifier - -

Prefilter(washable / anti-fungus) Yes Yes

ReliabilityHot start - YesSelf diagnosis Yes YesSoft dry operation Yes Yes

Convenience

Setting Temperature, Cooling 18 - 30 18 - 30Setting Temperature, Heating - 16 - 30Auto changeover - YesAuto cleaning Yes YesAuto operation(artificial intelligence) Yes -Auto restart operation Yes YesForced operation Yes YesSleep mode Yes YesSetting Temperature Range (Cooling) 18-30 18-30Setting Temperature Range (Heating) 16-30 16-30Temperature Increment 1 1Timer(Hr) Yes (24h On/Off) Yes (24h On/Off)

Individual

controlWireless remote controller(simple) - -Wireless LCD remote control Yes Yes


12/45

12

Dimensional Drawings SR-6RMG2-01A


250

1030

325210

70

70

69

56

Rightrear

pip

ing

Leftrear

piping

InstallationPlate

MeasuringTape

MeasuringTape

Hanger

Placealevelonraisedtab

UnitOutline

207

105

(Unit:mm)

460

570

LiberoR/E

CHASSISC

ODE:SC

4

5. Dimensional Drawings5.1 Indoor Unit


13/45

13

Dimensional DrawingsSR-6RMG2-01A


5.2 Outdoor Unit

1

GasPipeConnectionPort

PartName

AirDichargeGrille

LiquidPipeConnectionPort

ControlBox

No.

2 4

EarthScrew

531

R

emark

Note

1.Theun

itshouldbeinstalledaccordingtoinstallationmanualwhichis

inthep

roductbox.

2.Inana

reaoraapacehavingnoproperaircirculation,anairguide

should

beinstalledintheoutdoorunit.

76,Seongsan-dong,ChangwonCity,Gyeongnam,

641-713,Korea

www.lge.com/aircon

ditioner

CHASSISCOD

E:UE

OutdoorU

nit

Unit:mm


14/45

14

Wiring Diagrams SR-6RMG2-01A


6. Wiring Diagrams6.1 Indoor Units

CN-MOTORCN-U/D

CN-L/R

CN-OPTION

CN-DISP3

CN-HVB

CN-12V

CN-TH1

CN-DISP2

CN-SUB

Model : GS-C182C4B2, GS-C242C4B2


15/45

15

Wiring DiagramsSR-6RMG2-01A


Model : GS-H182C4B2, GS-H242C4B2

CN-U/D

CN-L/R

CN-DISP3

CN-SUB

CN-OPTION

CN-HVB

CN-12V

CN-TH1

CN-DISP2

CN-4WAY

CN-MOTOR


16/45

16

Wiring Diagrams SR-6RMG2-01A


CapacitorTerminal Block


6.2 Outdoor Unit


17/45

17

Wiring DiagramsSR-6RMG2-01A


TerminalBlock

Capacitor



18/45

18

Refrigerant Cycle Diagram SR-6RMG2-01A


7. Refrigerant Cycle Diagram

INDOOR UNIT OUTDOOR UNIT

HEATECHANGE(EVAPORATOR)

HEATECHANGE(CONDENSER)

COMPRESSORGAS SIDE

LIQUID SIDE

CAPILLARY TUBE

rotcennoCBCPnoitpircseD.COL

Th1 Thermistor for indoor air temperatureCN-TH1

Th2 Thermistor for evaporating temperature

INDOOR UNIT OUTDOOR UNIT

HEATECHANGE(EVAPORATOR)

HEATECHANGE(CONDENSER)

COMPRESSOR

ACCUMU%LATOR

GAS SIDE

3-WAY VALVE

LIQUID SIDE

3-WAY VALVE

CAPILLARY TUBE

CHECVALVE(Heating Model only)

COOLING

HEATING

REVERSING

VALVE(Heating Model Only)




19/45

19

Capacity TablesSR-6RMG2-01A


8. Capacity Tables

Model : GS-C182C4B2

Model : GS-H182C4B2

Model : GS-C242C4B2

Model : GS-H242C4B2

Cooling capacity

CWB CDB TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 14 20 4.40 3.41 1.30 4.30 3.37 1.55 4.10 3.28 1.80 3.98 3.21 1.90 3.83 3.14 2.02 3.74 3.10 2.09

16 22 5.13 3.87 1.32 5.02 3.83 1.57 4.79 3.72 1.83 4.64 3.64 1.93 4.47 3.55 2.05 4.37 3.50 2.12

18 25 5.73 4.21 1.34 5.60 4.16 1.59 5.34 4.03 1.86 5.18 3.94 1.96 4.99 3.84 2.08 4.87 3.78 2.15

19 27 5.99 4.35 1.37 5.86 4.30 1.62 5.59 4.16 1.89 5.42 4.07 1.99 5.22 3.96 2.12 5.10 3.90 2.19

22 30 6.58 4.61 1.38 6.44 4.55 1.64 6.13 4.40 1.91 5.95 4.29 2.02 5.73 4.18 2.14 5.60 4.10 2.21

24 32 6.82 4.69 1.40 6.68 4.62 1.66 6.37 4.46 1.94 6.17 4.35 2.04 5.95 4.23 2.17 5.81 4.15 2.25

Indoor Air

Temperature

Outdoor Air Temperature : CDB

20 25 32 35 40 43

CWB CDB TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI

14 20 4.40 3.36 1.30 4.30 3.33 1.55 4.10 3.24 1.80 3.98 3.17 1.90 3.83 3.10 2.02 3.74 3.06 2.09

16 22 5.13 3.82 1.32 5.02 3.78 1.57 4.79 3.67 1.83 4.64 3.59 1.93 4.47 3.50 2.05 4.37 3.45 2.12

18 25 5.73 4.15 1.34 5.60 4.10 1.59 5.34 3.98 1.86 5.18 3.89 1.96 4.99 3.79 2.08 4.87 3.73 2.15

19 27 5.99 4.29 1.37 5.86 4.24 1.62 5.59 4.11 1.89 5.42 4.01 1.99 5.22 3.91 2.12 5.10 3.85 2.19

22 30 6.58 4.55 1.38 6.44 4.49 1.64 6.13 4.34 1.91 5.95 4.24 2.02 5.73 4.12 2.14 5.60 4.05 2.21

24 32 6.82 4.63 1.40 6.68 4.56 1.66 6.37 4.40 1.94 6.17 4.29 2.04 5.95 4.17 2.17 5.81 4.10 2.25

Indoor Air

Temperature


20 25 32 35 40 43


14 20 5.70 4.18 1.77 5.58 4.14 2.10 5.32 4.03 2.44 5.16 3.95 2.58 4.97 3.86 2.74 4.86 3.81 2.8316 22 6.66 4.75 1.80 6.52 4.70 2.13 6.21 4.56 2.48 6.02 4.47 2.62 5.80 4.36 2.78 5.66 4.29 2.87

18 25 7.43 5.16 1.82 7.27 5.11 2.16 6.93 4.95 2.52 6.72 4.84 2.66 6.47 4.72 2.82 6.32 4.64 2.92

19 27 7.77 5.34 1.85 7.61 5.28 2.20 7.25 5.11 2.56 7.03 4.99 2.70 6.77 4.87 2.87 6.62 4.79 2.97

22 30 8.53 5.66 1.88 8.35 5.59 2.23 7.96 5.40 2.60 7.72 5.27 2.73 7.43 5.13 2.91 7.26 5.04 3.00

24 32 8.85 5.76 1.91 8.67 5.68 2.26 8.26 5.48 2.63 8.01 5.35 2.77 7.71 5.19 2.95 7.53 5.10 3.05

Indoor Air

Temperature


20 25 32 35 40 43

SymbolDB : Dry bulb temperature [C]WB : Wet bulb temperature [C]TC : Total capacity [kW]SHC : Sensible capacity [kW]PI : Power Input [kW]

(Comp.+ indoor fan motor+outdoor fan motor)

Notes1. All capacites are net, evaporator fan motor heat is deducted.2. Indicates nominal capacity.3. Direct interpolation is permissible. Do not extrapolate4. Capacities are based on the following conditions:

- Interconnecting Piping Length 7.5m- Level Difference of Zero.


14 20 5.70 4.24 1.87 5.58 4.20 2.21 5.32 4.09 2.58 5.16 4.00 2.72 4.97 3.92 2.89 4.86 3.86 2.99

16 22 6.66 4.82 1.90 6.52 4.77 2.25 6.21 4.63 2.62 6.02 4.53 2.76 5.80 4.42 2.94 5.66 4.35 3.03

18 25 7.43 5.24 1.93 7.27 5.18 2.28 6.93 5.02 2.66 6.72 4.91 2.80 6.47 4.78 2.98 6.32 4.71 3.08

19 27 7.77 5.41 1.96 7.61 5.35 2.32 7.25 5.18 2.71 7.03 5.06 2.85 6.77 4.93 3.03 6.62 4.85 3.13

22 30 8.53 5.74 1.98 8.35 5.67 2.35 7.96 5.48 2.74 7.72 5.35 2.89 7.43 5.20 3.07 7.26 5.11 3.17

24 32 8.85 5.84 2.01 8.67 5.76 2.38 8.26 5.56 2.78 8.01 5.42 2.93 7.71 5.27 3.11 7.53 5.17 3.22

Indoor Air

Temperature


20 25 32 35 40 43


20/45

20

Capacity Tables SR-6RMG2-01A


Model : GS-H182C4B2

Model : GS-H242C4B2

CDB TC PI TC PI TC PI TC PI TC PI TC PI TC PI TC PI

16 3.86 1.34 4.55 1.47 5.26 1.60 5.52 1.65 5.79 1.70 6.12 1.72 6.62 1.82 7.31 1.94

18 3.74 1.39 4.40 1.52 5.09 1.65 5.35 1.70 5.60 1.75 5.92 1.78 6.41 1.88 7.08 2.01

20 3.63 1.43 4.27 1.57 4.94 1.71 5.19 1.76 5.44 1.81 5.71 1.84 6.22 1.94 6.86 2.08

22 3.49 1.48 4.12 1.62 4.76 1.76 5.00 1.81 5.24 1.87 5.54 1.90 5.99 2.00 6.62 2.14

24 3.37 1.52 3.98 1.67 4.60 1.81 4.83 1.87 5.06 1.93 5.35 1.96 5.79 2.06 6.39 2.21

Indoor Air

Temperature

Outdoor Air Temperature : CWB

-10 -5 0 2 4 6 10 15

CDB TC PI TC PI TC PI TC PI TC PI TC PI TC PI TC PI

16 5.14 2.02 6.06 2.21 7.01 2.40 7.36 2.48 7.72 2.55 8.15 2.60 8.83 2.73 9.74 2.93

18 4.98 2.09 5.87 2.28 6.79 2.49 7.13 2.56 7.47 2.64 7.90 2.68 8.55 2.83 9.43 3.03

20 4.83 2.16 5.69 2.36 6.59 2.57 6.92 2.65 7.25 2.73 7.62 2.77 8.29 2.92 9.15 3.13

22 4.66 2.23 5.49 2.43 6.35 2.65 6.67 2.73 6.99 2.81 7.38 2.86 7.99 3.01 8.82 3.23

24 4.50 2.29 5.30 2.51 6.13 2.73 6.44 2.81 6.75 2.90 7.13 2.95 7.72 3.10 8.52 3.32

Indoor Air

Temperature

Outdoor Air Temperature : CWB

-10 -5 0 2 4 6 10 15

SymbolDB : Dry bulb temperature [C]WB : Wet bulb temperature [C]

TC : Total capacity [kW]SHC : Sensible capacity [kW]PI : Power Input [kW]

(Comp.+ indoor fan motor+outdoor fan motor)

Notes1. All capacites are net, evaporator fan motor heat is deducted.2. Indicates nominal capacity.

3. Direct interpolation is permissible. Do not extrapolate4. Capacities are based on the following conditions:- Interconnecting Piping Length 7.5m- Level Difference of Zero.

Heating capacity


21/45

21

Capacity Coefficient FactorSR-6RMG2-01A


9. Capacity Coefficient Factor

Outdoor unit

Indoor unit

A

B

Outdoor unit

Indoor unit

A

B

Capacity

kW (kBtu/h)

Pipe Size[mm(in)] Standard

Length m(ft)Max.

Elevation m(ft)Max.

Length m(ft)Additional Refrigerant

g/m(oz/ft)GAS LIQUID

5.3(18)12.7(1/2)

6.35(1/4) 5(16) 10(33) 15(49) 20(0.22)15.88(5/8)

7.0(24) 15.88(5/8) 9.52(3/8) 5(16) 10(33) 15(49) 30(0.32)

Model : GS-C182C4B2, GS-H182C4B2, GS-C242C4B2, GS-H242C4B2

Capacity is based on standard length and maximum allowable length is on the basis of reliability.

Additional refrigerant must be charged after 5m.

CAUTION

100

90

80

707.5 10 2015

18K/24K SC Chassis

Capacity(%)

Total Pipe Length(m)

100

90

80

707.5 10 2015

18K/24K SC Chassis

Capacity(%)

Total Pipe Length(m)

Cooling

Heating


22/45

22

Operation Range SR-6RMG2-01A


10. Operation Range

Operative: Intermittent operation due to the operationalconditions (indoor/outdoor temperature,humidity, load etc.) can cause the heatingcapacity to decrease

46

43

21

-5

18 32

Indoor Unit [C DB] Indoor Unit [C DB]

Standard operation

Operative

Warmingup

Operation

OutdoorUnit[CDB]

OutdoorUnit[CDB]

24

16 30

-10

-5

Operative

Continuousoperation

Operative

Without Low Ambient Kit

Cooling Heating

If outdoor temperature falls below 0C, the coolingcapacity and operating characteristics could be dif-ferent than rated.

Operative: Intermittent operation due to the operationalconditions (indoor/outdoor temperature,humidity, load etc.) can cause the heatingcapacity to decrease

46

43

21

-5

18 32Indoor Unit [C DB] Indoor Unit [C DB]

Standard operation

Operative

Warmingup

Operation

OutdoorUnit[CDB]

OutdoorUnit[CDB]

24

16 30

-10

-5

Operative

Continuousoperation

With Low Ambient Kit

Cooling Heating


23/45

23

Air Velocity and Temperature Distribution(Reference Data)SR-6RMG2-01A


11. Air Velocity and Temperature Distribution(Reference Data)

Model : GS-C182C4B2, GS-H182C4B2

General Wall Mouted 18 kBtu/h

CoolingDischarge angle:45

HeatingDischarge angle:50

Air velocity [m/s]

2.7m

2m

1m

0m1m2m3m4m5m6m7m8m

Temperature [ C]

2.7m

2m

1m

0m1m2m3m4m5m6m7m8m

0.751.25

1.0

1.5

0.5

25 24

23

Air velocity [m/s]

2.7m

2m

1m

0m1m2m3m4m5m6m7m8m

Temperature [C]

2.7m

2m

1m

0m1m2m3m4m5m6m7m8m

0.751.25

1.0

1.5

0.5

28 2930

31


24/45

24

Controller SR-6RMG2-01A


12. Controller

Type 1 (Wireless LCD)

Displayscreen

Control

panel

Display

screen

Controlpanel

JET

COOL

JET

COOL

C/F[5SEC]

C/F[5SEC]

Control panel Display screen Description

a F Plasma button*: Purifies the air by removingparticles that enter the indoor unit./ 4 Air circulation button*: Used to circulate theroom air without cooling or heating.l = Sleep mode auto button*: Sets the sleep modeauto operation.e y Temperature adjustment buttons: Adjusts the

room temperature when cooling and heating.

d - On/Off button: Turns the power on/off.g 7 v Indoor fan speed button: Adjusts the fanspeed.f A C

D B E

Operation mode selection button*: Selects theoperation mode.Cooling operation (A) / Auto operation or autochangeover (C) / Dehumidifying operation (D) /Heating operation (B) / Air circulation (E)

JET

COOL NJet cooling/heating button*: Warms up or coolsdown the indoor temperature within a short peri-

od of time.

i j H I Air flow direction button: Adjusts the air flowdirection vertically or horizontally.k S Temperature display button: Displays the roomtemperature.

m n z Timer button: Sets the current time and the start/ end time.

cb

u

J G P

Functions button*: Adjusts the time and setsthe special functions.J: Auto clean / G: Operates energy saving cool-ing / P: Adjusts the brightness of the indoor unit

displayp - Set/clear button: Sets or cancels functions.r - Reset button: Initialize the air conditioner set-tings.

* Some functions may not be supported, depending on the model.


25/45

25

InstallationSR-6RMG2-01A


13. Installation

13.1 Installation Map

Vinyl tape (Wide) Apply after carrying out a drainage test. To carry out the drainage

test, remove the air filters and pour water into the heat

exchanger.

Saddle

Gas side pipingLiquid side piping

Additional drain pipe

Vinyl tape (Narrow)

Drain Hose

Base Plate

Air Outlet

Air Inlet

Connecting cable

Tubing Cover

Sleeve

Bushing-Sleeve

Putty(Gum Type Sealant)

Bend the pipe as closelyon the wall as possible,but be careful that itdoesn't break.

Installation plate

* The feature can be changed according to the type of model.

() You should purchase the installation parts.

NOTE


26/45

26

Installation SR-6RMG2-01A


13.2 Select the best Location

Indoor unit

1. There should not be any heat or steam near the unit.

2. Select a place where there are no obstacles around the

unit.

3. Make sure that condensation drainage can be conveniently

routed away.

5. Ensure that the gap between a wall and the left (or right) of

the unit is more than 100mm. The unit should be installed

as high as possible on the wall, allowing a minimum of

200mm from ceiling.

6. Use a metal detector to locate studs to prevent unneces-

sary damage to the wall.

* The feature can be changed according to the type of

model.

Outdoor unit

1. If an awning is built over the unit to prevent direct sunlight

or rain exposure, make sure that heat radiation from the

condenser is not restricted.

2. Ensure that the space around the back side and other

sides is more than 300mm. The space in front of the unit

should be more than 700mm.

3. Do not place animals and plants in the path of the warmair.

4. Take the weight of the air conditioner into account and

select a place where noise and vibration are minimum.

5. Select a place where the warm air and noise from the air

conditioner do not disturb neighbors.

More than 200

More than100

More than 2300

More than100

(Unit : mm)

Install the indoor unit on the wall where the height from the floor is more than 2300mm.

CAUTION

Sunroof

Fenceorobstacles

More than300

More than300

More than700

More than600

(Unit : mm)


27/45

27



2. Measure the wall and mark the centerline. It is also important to

use caution concerning the location of the installation plate.

Routing of the wiring to power outlets is through the walls typical-ly. Drilling the hole through the wall for piping connections must be

done safely.

The wall you select should be strong and solid enough to prevent

vibration

1. Mount the installation plate on the wall with type "A" screws. If

mounting the unit on a concrete wall, use anchor bolts.

Mount the installation plate horizontally by aligning the center-

line using Horizontal meter .

6565

69 56

Rightrearpiping

Leftrearpiping

Installation Plate

Measuring Tape

Measuring TapeHanger

Place a level on raised tabUnit Outline

207105

(Unit : mm)

460 570

Installation Plate

ChassisHook

Type "A" Screws

Drill the piping hole with a 65mm hole core drill. Drill thepiping hole at either the right or the left with the hole

slightly slanted to the outdoor side.

5-7mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Bushing

Sleeve

13.3 Fixing Installation Plate

13.4 Drill a Hole in the Wall

Use the sleeve to prevent damage for tube assembly.

CAUTION


28/45

28

SR-6RMG2-01A


Installation

13.5 Flaring Work

Main cause for gas leakage is due to defect of flaring work. Carry out correct flaring work in the following procedure.

Cut the pipes and the cable.

1. Use the piping kit accessory or the pipes purchased locally.

2. Measure the distance between the indoor and the outdoor unit.

3. Cut the pipes a little longer than measured distance.

4. Cut the cable 1.5m longer than the pipe length.

Burrs removal

1. Completely remove all burrs from the cut cross section of pipe/tube.

2. While removing the burrs, hold the end of the pipe in downward direc-

tion in order to avoid dropping burrs into the tubing.

Putting nut on

- Remove flare nuts attached to indoor and outdoor units, then put them

on the pipe/tube which have completed its burr removal.

(not possible to put them on after finishing flare work)

Flaring work1. Firmly hold copper pipe in a bar with the dimension shown in

table below.

2. Carry out flaring work with the flaring tool.

Copperpipe 90 Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar"A"

Outside diameter A Thickness

mm inch mm mm

6.35 1/4" 1.1~1.3 0.7

9.52 3/8" 1.5~1.7 0.812.7 1/2" 1.6~1.8 0.8

15.88 5/8" 1.6~1.8 1.0

19.05 3/4" 1.9~2.1 1.0


29/45

29

SR-6RMG2-01A


Installation

Check

1. Compare the flared work with the figures given below.

2. If a flared section is defective, cut it off and do flaring work

again.

Inclined

Inside is shiny without scratches

Smooth all round

Even lengthall round

Surfacedamaged

Cracked Uneventhickness

= Improper flaring =

13.6 Connecting the pipes

1. Pull the screw caps at the bottom of the indoor unit

2. Remove the chassis cover from the unit by loosing 3 screws

3. Pull back the tubing holder.

4. Remove the pipe port cover and position the piping.


Chassis cover

Right

Back side view

Tubing holder

Backwards

Left

Pipe Port


30/45

30

SR-6RMG2-01A


Installation

Good case

Press the tubing cover and slowly unfold the tubing to downward. And then bend to the left side slowly.

Bad case Following bending case from right to left directly may cause damage to the tubing.


Installation Information. For right piping. Follow the instruction above.

CAUTION


31/45

31

SR-6RMG2-01A


Installation

1. Hook the indoor unit onto the upper portion of the installation plate.( engage the three hooks at the top of the indoor unit with

the upper edge of the installation plate) Ensure that the hooks are properly seated on the installation plate by moving it left

and right

2. Unlock the tubing holder from the chassis and mount between the chassis and installation plate in order to separate the bot-

tom side of the indoor unit from the wall.


Installation plate

1

2

Tubing Holder

13.7 Installation of Indoor Unit


32/45

32

Installation SR-6RMG2-01A


3. Insert the connecting cable through the bottom side of

indoor unit and connect the cable

Open the Front Grille

Support the Front Grille with supporter

Open the Control Cover

Connect the connecting cable

Control Cover

Case 1 Case 2 Case 3

4. Tape the tubing pipe, drain hose and the connection cable. Be sure that the drain hose is located at the lowest side of the

bundle. Locating at the upper side can cause overflow from the drain pan through the inside of the unit.


Connecting pipe

Connectingcable

Tape

Drain hose

Indoor Outdoor

Indoor Unit

Drain hose

Indoor UnitDrain hose

Insulation(More than 100~300mm

length and 7mm thickness)

Extensiondrain hose

Drain hose

Tape

Connecting pipe

Connectingcable

Drain hose

If the extension drain hose is routed inside the room,insulate the hose with an insulation material* so that drip-ping from sweating (condensation) could not damage fur-

niture or floors.

Foamed polyethylene or equivalent is recommended.

CAUTION


33/45

33



Connecting the installation pipe and drain

hose to the indoor unit.

1. Align the center of the pipes and sufficiently tighten the

flare nut by hand

2. Tighten the flare nut with a wrench

3. When needed to extend the drain hose of indoor unit,

assembly the drain pipe as shown on the drawing

Indoor unit tubing Flare nut Pipes

Wrench

Indoor unit tubing

Open-end wrench (fixed)

Connection pipe

Flare nut

Vinyl tape(narrow)Adhesive

Drain pipe

Indoor unit drain hose

Wrap the insulation material around the con-

necting portion.

1. Overlap the connection pipe insulation material and the

indoor unit pipe insulation material. Bind them together with

vinyl tape so that there may be no gap.

2. Wrap the area which accommodates the rear piping hous-

ing section with vinyl tape.

3. Bundle the piping and drain hose together by wrapping

them with vinyl tape sufficient enough to cover where they

fit into the rear piping housing section.

Insulation material

Wrap with vinyl tape

Drain hose

Pipe

Vinyl tape(wide)

Vinyl tape(narrow)

Connection pipe

Connecting cable

Vinyl tape (wide) Wrap with vinyl tape

Indoor unit pipe

Pipe

Outside Diameter Torque

mm inch kgfcm Nm

6.35 1/4 180~250 17.6~24.5

9.52 3/8 340~420 33.3~41.2

12.7 1/2 550~660 53.9~64.7

15.88 5/8 630~820 61.7~80.4

19.05 3/4 990~1210 97~118.6


34/45

34

SR-6RMG2-01A


Installation

Finishing the indoor unit installation

1. Mount the tubing holder in the original positon.

2. Ensure that the hooks are properly seated on the installa-

tion plate by moving it left and right.

3. Press the lower left and right sides of the unit against the

installation plate until the hooks engage into their slots(clicking sound).

4. Finish the assembly by screwing the unit to the installation

plate by using two pieces of type "C" screws. And assemble

a chassis cover.

5. Reconvey the chassis cover in Original place.

Type 'C' screw

Outdoor Unit Installation

1. Remove the tubing cover from the unit by loosening thescrew.

Cover control

Tubing Cover

2. Align the center of the pipings and sufficiently tighten the

flare nut by hand.


35/45

35

SR-6RMG2-01A


Installation

3. Finally, tighten the flare nut with torque wrench until the

wrench clicks.

When tightening the flare nut with torque wrench, ensure

the direction for tightening follows the arrow on the

wrench.

Outdoor unit

Gas side

Liquid side

Cap

3-way or

2-way valve

3-way valveOutside Diameter Torque

mm inch kgfcm Nm

6.35 1/4 180~250 17.6~24.5

9.52 3/8 340~420 33.3~41.2

12.7 1/2 550~660 53.9~64.7

15.88 5/8 630~820 61.7~80.4

19.05 3/4 990~1210 97~118.6


36/45

36

SR-6RMG2-01A


Installation

13.8 Connecting the Cables

Indoor

Connect the cable to the indoor unit by connecting the wires to the terminals on the control board individually according to the

outdoor unit connection. (Ensure that the color of the wires of the outdoor unit and the terminal No. are the same as those of

the indoor unit.)

The circuit diagram is a subject to change without notice.

The earth wire should be longer than the common wires.

When installing, refer to the circuit diagram on the chassis cover.

Connect the wires firmly so that they may not be pulled out easily.

Connect the wires according to color codes, referring to the wiring diagram.

CAUTION

The power cord connected to the unit should be selected according to the following specifications (Cable Type

approved by IEC 60245 or IEC 60227).

CAUTION

The power connecting cable connecting the indoor and outdoor unit should be selected according to the followingspecifications (Cable type approved by IEC 60245 or IEC 60227).

103mm

20mm

GN/YL

103mm

20mm

GN/YL

103mm

20mm

GN/YL

103mm

(mm2)

POWER CORD

Capacity[kW (Btu/h)]

5.3 (18) 7.0 (24)

Nomal Cross-Section Area

1.5 2.5

Unit Indoor Indoor

Cable Type H05VV-F H05VV_F

(mm2)

POWER CONNECTING CABLE


5.3 (18) 7.0 (24)


1.5 2.5

Unit Indoor Indoor

Cable Type H07RN-F H07RN-F

(mm2)

COMMUNICATION CONNECTING CABLE


5.3 (18) 7.0 (24)


0.75 0.75

Unit Indoor Indoor

Cable Type H05RN-F H05RN-F


37/45

37

SR-6RMG2-01A


Installation

Outdoor

1 Remove the control cover from the unit by loosening the

screw. Connect the wires to the terminals on the control

board individually.

2 Secure the cable onto the control board with the cord

clamp.3 Refix the control cover to the original position with the

screw.

4 Use a recognized circuit breaker between the power source

and the unit.

A disconnecting device to adequately disconnect all supply

lines must be fitted.

* Round Pressure terminal and connecting requirement

Provide the circuit breaker between power source and the

unit as shown by

CAUTION

According to the confirmation of the above conditions, pre-pare the wiring as follows.

1. Never fail to have an individual power circuit specifically for

the air conditioner. As for the method of wiring, be guided

by the circuit diagram posted on the inside of control cover.

2. The screw which fasten the wiring in the casing of electrical

fittings are liable to become loose from vibrations to which

the unit is subjected during the transportation. Check them

and make sure that They all are tightly fastened. (If they

are loose, it could cause burn-out of the wires.)

3. Specification of power source.

4. Confirm that electrical capacity is sufficient.

5. See that the starting voltage is maintained at more than 90

percent of the rated voltage marked on the name plate.

6. Confirm that the cable thickness is as specified in the

power source specification.

(Particularly note the relation between cable length and

thickness.

7. Always install an earth leakage circuit breaker in a wet or

moist area.

8. The following would be caused by voltage drop.

- Vibration of a magnetic switch, which will damage the

contact point, fuse breaking, disturbance of the normalfunction of the overload.

9. The means for disconnection from a power supply shall be

incorporated in the fixed wiring and have an air gap contact

separation of at least 3mm in each active(phase) conduc-

tors.

CAUTION

Cover control

Connecting

cable

1(L) 2(N) 3 4

CASE 1

1(L) 2(N) 3

CASE 3

1(L) 2(N) 3 4

CASE 2

The earth wire shouldhe earth wire should

be longer than thee longer than the

common wires.ommon wires

The earth wire shouldbe longer than thecommon wires.

Over5mm

Round pressureterminal

Power wire

The earth wire should

be longer than the

common wires

AirConditioner

Main power source

Circuit BreakerUse a circuit breakeor time delay fuse.

Circuit

Breaker (A)

Capacity [kW (kBtu/h)]

5.3 (18) 7.0 (24)

20 30


38/45

38

SR-6RMG2-01A


Installation

To check the drainage.

1. Pour a glass of water on the evaporator.

2 Ensure the water flows through the drain hose of the

indoor unit without any leakage and goes out the drain

exit.

Drain piping

1. The drain hose should point downward for easy drain flow.

2. Do not set the drain hose like the following.


Drain Pan

DrainHose

LeakageChecking

Connecting areadrain hose

Leakagechecking

Downward slope

Do not raiseAccumulateddrain water

Tip of drain hosedipped in water

Air

WavingWaterleakage

Waterleakage Ditch

Less than50mm gap

Waterleakage

13.9 Checking the Drainage


39/45

39

SR-6RMG2-01A


Installation

13.10 Forming the Piping

Form the piping by wrapping the connecting por-tion of the indoor unit with insulation material andsecure it with two kinds of vinyl tapes.

- If you want to connect an additional drain hose, theend of the drain outlet should be routed above theground. Secure the drain hose appropriately.

In cases, where the outdoor unit is installed belowthe Indoor unit, perform the following.

1. Tape the piping, drain hose and connecting cablefrom down to up.

2. Secure the tapped piping along the exterior wallusing saddle or equivalent.

In cases, where the outdoor unit is installed abovethe Indoor unit, perform the following.

1. Tape the piping and connecting cable from down to up.

2. Secure the taped piping along the exterior wall. Form a

trap to prevent water entering the room.

3. Fix the piping onto the wall using saddle or equivalent

Drain hoseVinyl tape(narrow)

Pipe

Wrap withvinyl tape(wide)

Taping

Saddle

Drain hose

PipingsConnecting cable

Seal small openingsaround pipings with agum type sealant.

Trap is required to prevent waterfrom entering into electrical parts.

Seal a small openingaround the pipingswith gum type sealant.

Trap

Trap


40/45

40

SR-6RMG2-01A


Installation

13.11 Air Purging

The air and moisture remaining in the refrigerant system have undesirable effects as indicated below.1. Pressure in the system rises.

2. Operating current rises.

3. Cooling(or heating) efficiency drops.

4. Moisture in the refrigerant circuit may freeze and block capillary tubing.

5. Water may lead to corrosion of parts in the refrigeration system.

Therefore, after evacuating the system, take a leak test for the piping and tubing between the indoor and outdoor unit.

Air purging with vacuum pump

1. Preparation Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have been properly connected and all

wiring for the test run has been completed. Remove the service valve caps from both the gas and the liquid side on the outdoor unit.

Note that both the liquid and the gas side service valves on the outdoor unit are kept closed at this stage.

2. Leak test Connect the manifold valve(with pressure gauges) and dry nitrogen gas cylinder to this service port with charge hoses.

Be sure to use a manifold valve for air purging. If it is not available, use a stop valve for this purpose. The knob of the 3-way

valve must always be kept close.

- Pressurize the system to maximum 250 P.S.I.G. (R-22 model) or 400 P.S.I.G (R-410A model) with dry Nitrogen gas and

close the cylinder valve when the gauge reading reaches 250 P.S.I.G (R-22 model) or 400 P.S.I.G (R-410A model). Next

step is leak test with liquid soap.

To avoid nitrogen entering the refrigerant system in a liquid state, the top of the cylinder must be higher than its bottom when

you pressurize the system. Usually, the cylinder is used in a vertical standing position.

There is a risk of fire and explosion.

Inert gas (nitrogen) should be used when you check plumbing leaks, cleaning or repairs of pipes etc.

If you are using combustible gases including oxygen, product may have the risk of fires and explosions.

1. Do a leak test of all joints of the tubing(both indoor and out-

door) and both gas and liquid side service valves.

Bubbles indicate a leak. Be sure to wipe off the soap with a

clean cloth.

2. After the system is found to be free of leaks, relieve the nitro-

gen pressure by loosening the charge hose connector at the

nitrogen cylinder. When the system pressure is reduced tonormal, disconnect the hose from the cylinder.

*The feature can be changed according a type of model.

CAUTION

CAUTION

WARNING

Lo Hi

Outdoor unit

Manifold valve

Charge hose

Nitrogen gascylinder(in verticalstanding position)

Pressuregauge

Indoor unit


41/45

41

SR-6RMG2-01A


Installation

Soap water method

1. Remove the caps from the 2-way and 3-way valves.

2. Remove the service-port cap from the 3-way valve.

3. Apply a soap water or a liquid neutral detergent on the

indoor unit connection or outdoor unit connections by a

soft brush to check for leakage of the connecting points of

the piping.4. If bubbles come out, the pipes have leakage

Evacuation

1. Connect the charge hose end described in the preceding

steps to the vacuum pump to evacuate the tubing and indoorunit.

Confirm the "Lo" knob of the pressure Gauge is open. Then,

run the vacuum pump.

The operation time for evacuation varies with tubing length

and capacity of the pump. The following table shows the timerequired for Evacuation.

2. When the desired vacuum is reached, close the knob of the 3-way valve and stop the vacuum pump.

Finishing the Job

1. With a service valve wrench, turn the valve of liquid sidecounter-clockwise to fully open the valve

2. Turn the valve of gas side counter clockwise to fully open the

valve

3. Loosen the charge hose connected to the gas side service

port slightly to release the pressure, then remove the hose.

4. Replace the flare nut and its bonnet on the gas side serviceport and fasten the flare nut securely with an adjustable

wrench. This process is very important to prevent leakage

from the system.

5. Replace the valve caps at both gas and liquid side service

valves and fasten them tight.This completes air purging with a vacuum pump.

6. Replace the pipe cover to the outdoor unit by one screw

Now the air conditioner is ready for test run.


Outdoor unitGas side

Liquid side

Cap

3-way or2-way valve

3-way valve

Outdoor unit

Lo Hi

Manifold valve

Vacuum pump

Pressuregauge

Open Close

Indoor unit

Required time for Evacuation when 30 gal/h vacuumpump is used

If tubing length is less than10m (33 ft)

If tubing length is longerthan 10m (33 ft)

10 min. or more 15 min. or more


42/45

42

SR-6RMG2-01A


Installation

If the actual pressure is higher than shown, the system is most likely over-charged, and charge should be removed. If the

actual pressure are lower than shown, the system is most likely undercharged, and charge should be added.

NOTE

Pump downThis is performed when the unit is relocated or the refrigerant circuit is serviced.

Pump Down means collecting all refrigerant into the outdoor unit without the loss of refrigerant.

Be sure to perform Pump Down procedure in the cooling mode.

Pump Down Procedure1. Connect a low-pressure gauge manifold hose to the charge port on the gas side service valve.

2. Open the gas side service valve halfway and purge the air in the manifold hose using the refrigerant.

3. Close the liquid side service valve(all the way).

4. Turn on the unit's operating switch and start the cooling operation.

5. When the low-pressure gauge reading becomes 1 to 0.5kg/cm2 G(14.2 to 7.1 P.S.I.G.), fully close the gas side valve and

then quickly turn off the unit. Now Pump Down procedure is completed, and all refrigerant is collected into the outdoor unit.

CAUTION

Settlement of outdoor unit1. Fix the outdoor unit with a bolt and nut(10mm) tightly and

horizontally on a concrete or rigid mount.

2. When installing on the wall, roof or rooftop, anchor the

mounting base securely with a nail or wire assuming the

influence of wind and earthquake.

3. If the vibration of the unit is transmitted to the pipe, securethe unit with an anti-vibration rubber.

Evaluation of the performanceOperate the unit for 15~20 minutes, then check the system

refrigerant charge:

1. Measure the pressure of the gas side service valve.

2. Measure the air temperature from inlet and outlet of air

conditiioner.

3. Ensure the difference between the inlet and outlet temper-

ature is more than 8C.

4. For reference; the gas side pressure at optimum condition

is shown on table (cooling)

The air conditioner is now ready to use.

*The feature can be changed according a type of model.

Bolt

Tubing connection

Dischargetemperature

Discharge air

Intake temperature

Refrigerant

Outside

ambient

TEMP.

The pressure of the

gas side service valve.

R22 35C (95F)4~5kg/cm2G

(56.8~71.0 P.S.I.G.)

R410A 35C(95F)8.5~9.5kg/cm2G

(120~135 P.S.I.G.)


43/45

43

SR-6RMG2-01A


Installation

13.12 Installation of filters

1. Pull out the triple filter and allergy free filter from the separately

packed plastic bag.

2. Insert the triple filter into the left case and insert the allergy free

filter into the right case.

3. Detach two nitto tapes from the plasma filter.


Virus & Allergy Safe Filter+ Triple Filter

CyclotronPlasma Filter

13.13 Test Running

- Check that all tubing and wiring are properly connected.

- Check that the gas and liquid side service valves are fully open.

Prepare remote controller

Insert batteries before using the remote control. The batterytype used is AAA (1.5 V).

1. Remove the battery cover.

2. Insert the new batteries and make sure that the + and - ter-

minals of the batteries are installed correctly.

3. Reattach the battery cover.

Use 2 AAA(1.5volt) batteries. Do not use rechargeable

batteries.

Remove the batteries from the remote controller if the sys-tem is not used for a long time

NOTE


44/45

44

SR-6RMG2-01A


Installation

13.14 Installation Guide at the Seaside

Air conditioners should not be installed in areas where corrosive gases, such as acid or alkaline gas, are produced.

Do not install the product where it could be exposed to sea wind (salty wind) directly. It can result corrosion on the product.

Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or inefficient performance.

If outdoor unit is installed close to the seaside, it should avoid direct exposure to the sea wind. Otherwise it needs addition-

al anticorrosion treatment on the heat exchanger.

CAUTION

Selecting the location(Outdoor Unit)

1. If the outdoor unit is to be installed close to the seaside, direct exposure to the sea wind should be avoided. Install the out-

door unit on the opposite side of the sea wind direction.

2. In case, to install the outdoor unit on the seaside, set up a windbreak not to be exposed to the sea wind.

It should be strong enough like concrete to prevent the

sea wind from the sea.

The height and width should be more than 150% of theoutdoor unit.

More than 70cm(s) of space should be kept between

outdoor. Unit and windbreak for easy air flow.

Select a well-drained place.

Sea wind Sea wind

Sea wind

Windbreak

1. If you cant meet above guide line in the seaside installation, please contact LG Electronics for the additionalanticorrosion.

2. Periodic ( more than once/year ) cleaning of the dust or salt particles stuck on the heat exchanger by usingwater


45/45

P/No.: MFL67839902

Air Conditioner20 Yeouido-dong, Yeongdeungpo-gu,

Yeouido P.O.Box 335 Seoul,

150-721, Korea.

http://www.lgeaircon.com

pdb saudi split (titan gold plus)

Documents