Block Diagram

Overview PAN-3UVPX-ZYNQ+ is a 3U OpenVPX module based on the Zynq UltraScale+

MPSoC from Xilinx.

The Zynq UltraScale+ integrates a Quad-core ARM Cortex-A53 based Application

Processing Unit (APU), a Dual-core ARM Cortex-R5 based Real-Time Processing

Unit (RPU), a ARM Mali based Graphic Processing Unit (GPU) and an UltraScale+

Programmable Logic (PL) in a single device.

It also include on-chip memory, external memory interfaces, and a rich set of pe-

ripheral connectivity interfaces.

The first version of the board is equipped with a XCZU9EG-1FFVC900 device tightly

coupled to 2/4GB of 64-bit + 8-bit ECC of DDR4 PS memory.

For I/O interface, a on-board FMC slot compliant with the Vita 57.1 HPC standard

with 58 LVDS and 10 GTH, allowing a wide range of applications such as SDR, Video

CODECs, DSPs and multi-axes motors controller.

© PanaTeQ June 2016 Version 1.2

Key Features 3U OpenVPX Compliant

Xilinx Zynq UltraScale+ MPSoC

2/4GB DDR4 64-bit PS Memory with 8-bit ECC

FMC Slot HPC with 58x LVDS 10x GTH

On-board PCIe Switch for up to 8x PCIe x1 Gen2 VPX-P1 links

eMMC up to 64GB

MRAM 512KB

1x Display Port Video Out

1x SATA 3.1

4x USB 2.0

2x RS-232/422/485

Module Management Controller

Air Cooled and Coneduction Cooled version

PAN-3UVPX-ZYNQ+ 3U VPX Xilinx Zynq UltraScale+ MPSoC with FMC slot

www.panateq.com

Typical Applications Video and Signal Processing

Software Defined Radio (SDR)

Electronic Warfare

Radar / Sonar

Encrypted Networking

4DSP FMC 120 JESD204B ADC/DAC

4DSP FMC 424 Dual QSFP+

Processing System PS

DDR4-2400

2/4GB

72-bit DDR

DDR4

Memory

Ctl

Quad-Core A53

DP1

CP (UP)

PCIe Gen2

Switch

16-Lanes 16-PortsDP2

VPX-P1

1x PCIe x4 or x4 PCIex1

1x PCIe x4 or x4 PCIex1

MMC

VITA 46.11

2x UARTs

DP

USB 2.0

Switch

IC

2x 1000BT

NAND

FLASH

8-64GB

eMMC

2x PHYs

Magnetics

4x GTH

LVDS

HB[0:21]

QSPI

FLASH

SerDes

10x GTH

SPIVPX_P0

GPU

MALI

LVDS

HA[0:23]

LVDS

LA[0:33]

RS-232

R-422

RS-485

HDMI

TxVPX-P2

3x USB 2.0

2x SATA 3.1

GPIO[0-7]

FMC-J1 HPC Connector

1x PCIex1 Gen2

MRAM

HDMI

2x RGMII

1x USB 2.01x USB 2.0

2x SATA

3.1

2x CAN4x GTR

PCIe

X4 Gen2

RC/EP

2x UART

2x USB

2x CAN

Programable

Logic PL

UltraScale+

10x

GTH

4x

GTH

Dual-Core R5

4x GETH

MAC2x

GTH

Xilinx ZCU9G-FFVC900

4DSP FMC 432 Dual 1000BaseT

Board Specifications

3U VPX Interfaces3U VPX Interfaces

VITA 46.0 VPX Specifications compliant

On-board PCIe Gen2 Switch 2x PCIe x4 Gen1 or 8x PCIe x1 link RC/EP connected to Zynq Processing System

4x SerDes GTH @16.3 Gb/s directly connected to ZynQ Programming Logique

2x1000BASE-BX links towards Switching Fabric

2x1000BASE-TX, 2x RS-232/422/485, 4x USB 2.0, 1x SATA 3.1

1x Display Port Video Out

8x GPIO

Module Management Control (MMC) Interface implemeting IPMI for temperature monitoring

JTAG

Xilinx Zynq UltraScale+ MPSoC (16nm Technology)Xilinx Zynq UltraScale+ MPSoC (16nm Technology)

Supported Devices:XVZU6EG-1FFVC900 / XCZU9EG-1FFVC900 / XCZU15EG-1FFVC900

Processing System : Quad-Core ARM A53, Dual-Core ARM R5, GPU Mali-400, 2x SATA, 2x USB, 4x GETH MACs

Programmable Logic: 214K LUTs (ZU6EG) / 274K LUTs (ZU9EG) / 341K LUTs (ZU15EG)

On-Chip Memories: 25.1Mb (ZU6EG) / 32Mb (ZU9EG) / 57.7Mb (ZU15EG)

DSP Slices: 1973 (ZU6EG) / 2520 (ZU9EG) / 3528 (ZU15EG)

SerDes: 24 full duplex, high performance, GTH multi-gigabit SerDes tranceivers @ 16.3 Gb/s

2x 10-bit, 1MSPS ADCs for System Monitoring

Supported by PanaTeQ’s FPGA Development Kit (PAN-FDK)

External MemoriesExternal Memories

2GB DDR4-2400 Processor System memory, 64-bits data, 8-bit ECC 2x 512Mb of QSPI NOR Flash memory for booting FPGA Zynq and Firmware 512KB of SPI MRAM (NVRAM) eMMC for up to 64GB NAND Flash memory

VITA 57 FMC SlotVITA 57 FMC Slot

Fully compliant to VITA 57.1. High Pin Count (HPC) connector 10x high-performance GTH SerDes @16.3 Gb/s to/from FPGA Zynq 58x LVDS pairs to/from FPGA Zynq 2x clocks to FPGA Zynq 2x clocks from FPGA Zynq

Pre-Ordering Information

PAN-3UVPX-ZYNQ+B : Air Cooled

PAN-3UVPX-ZYNQ+BCC : Conduction Cooled

PanaTeQ Engineering At Your Service

© PanaTeQ

Contact Information

info@panateq.com

www.panateq.com

Xilinx Zynq UltraScale+ MPSoC Processing System Highlights

Applications processing unit (APU) with quad-core ARM® Cortex™-A53 processors:

Next-generation ARMv8 architecture supporting 32- or 64-bit data widths

Ideal for Linux and bare-metal SMP/AMP application systems

Real-time processing unit (RPU) with dual-core ARM Cortex-R5 processors:

Low-latency, highly deterministic performance APU offloading

New integrated hardened multimedia blocks:

Graphics processing unit (GPU) [ARM Mali™-400MP2]

4Kx2K 60fps video encoder/decoder (VCU) [in select devices]

4Kx2K 30fps DisplayPort interface

New integrated high-speed peripherals:

PCIe® Gen1 or Gen2 root complex and integrated Endpoint block in x1, x2, and x4 lanes

USB 3.0/2.0 with host, device, and OTG modes

Gigabit Ethernet with jumbo frames and precision time protocol

SATA 3.1 host

Dedicated quad transceivers up to 6Gb/s

General and boot peripherals:

CAN, I2C, QSPI, SD, eMMC, and NAND flash interfaces

GPIO, UART, and trace ports

6-port DDR controller with ECC, supporting x32 and x64 DDR3, DDR3L, LPDDR3, LPDDR4, DDR4

Integrated platform management unit (PMU) supporting multiple power domains

Integrated configuration security unit (CSU)

TrustZone support

Peripheral and memory protection

PanaTeQ Engineering At Your Service

© PanaTeQ www.panateq.com